GPD Technology GPD-WIN WIN User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3192044
Application ID	fLMcZQtYVvraWf14hq1g1A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	120.51kB (1506364 bits)
Date Submitted	2016-11-10 00:00:00
Date Available	2016-11-10 00:00:00
Creation Date	2016-09-30 15:55:24
Producing Software	Adobe Acrobat Pro 9.0.0
Document Lastmod	2016-09-30 15:55:24
Document Title	User Manual
Document Creator	Adobe Acrobat Pro 9.0.0
Document Author:	zkh

User manual
Model:GPD WIN
Brand:GPD
One. To Start( start up)
1. Press power button
to start.
2. The computer enter power-on self-test and system guide
3. Enter Windows 10 interface, like picture below:
 Two Lay out (power off)
1. Click system tray bottom left logo
2. Click “power” selection
3. Click the “power off” when popup a dialog box, like below pitcture:
 Three Mouse operation
The device provide joystick and mouse mode switch, when switch to mouse mode, you
need slip the button to the middle. Like below:

Left joystick is taken as rolling button of mouse, to use to rolling up or down the
pages.

L1 L2 is taken as left button of mouse

R1 R2 is taken as right button of mouse
 How to adjust the mouse double click speed and pointer movi
ng speed below:

First step: double click the control panel, like below picture:

Second step: Click” Check device and printer”

The third step: Click right on the mouse icon, select “mouse setting”, start “mous
e” attribute dialog box.

The fourth step: adjust on the “speed” line.

The fifth step: Click “Pointer Options” label, adjust pointer movement speed.
 Four Joystick operation
GPD WIN support Dinput and Xinput two joystick modes, they matches Direct Input a
nd Xbox Input mode.
 Switch Dinput mode
Switch joystick mode to Dinput mode, need to move the button to left side, like below
picture:
To test the effectiveness of each button :

The first step: Double click control panel

The second step: click “check device and printer”

The third step: right click joystick icon, choose “Controller for PC”

The fourth step: Click the “attribute” when popup the dialog box

The fifth step: When popup” Controller for PC attribute “dialog box, please press
the cross button/joystick/shoulder button/function buttons to test the effectiveness.
 Switch to Xinput mode
Switch joystick mode to Dinput mode, need to move the button to left side, like below
picture:
On how to test the effectiveness of the buttons is blow:

The first step: double click the control panel

The second step: “Check device and printer”

The third step: Right click joystick icon, click “Controller for Windows”

The fourth step: Click the “attribute” when popup a dialog box.

The fifth step: When popup a dialog box” Controller for Windows attribute”, pleas
e press the cross button and joystick/shoulder button/function buttons to test the eff
ectiveness.
 Use the keyboard
The keyboard is a integrated highly QWERTY keyboard. The default output for first ro
w is number keys. If you want to switch to F1-F12 button/ special character just need
to press the Fn/Ctrl at the same time.
PgUp/Home/PgDn/End and     buttons overlap, the default output is   
, press the Fn button to switch to PgUp/Home/PgDn/End modes.
 Six Networking operation

The first step: Click the Wi-Fi logo on bottom right corner of the system tray

The second step: Click to connect

The third step: Input the pass words

The fourth step: When the system tray display
, that means connect successfull
y.
 Seven Connect to Bluetooth device operation

The first step: Click the Start menu system

The second step: Click the setting

The third step: When popup the “setting”, click the “device” icon.

The fourth step: Click the “Bluetooth”, start the “manage Bluetooth device”

The fifth step: If there is Bluetooth device within 10 meters around, the computer
can recognize automatically, click and enter the passwords to finish Wi-Fi connecti
on.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: GPD-WIN
(FCC ID: 2AJQ5GPD-WIN) has also been tested against this SAR limit. The highest SAR value reported
under this standard during product certification for use at the Wrist is 0.962W/kg and when properly worn
on the body is 0.640W/kg. This device was tested for typical body-worn operations with the back of the
handset kept 0mm/10mm from the body. To maintain compliance with FCC RF exposure requirements,
use accessories that maintain a 0mm/10mm separation distance between the user's body and the back
of the handset. The use of belt clips, holsters and similar accessories should not contain metallic
components in its assembly. The use of accessories that do not satisfy these requirements may not
comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a
minimum separation distance of 0mm/10mm must be maintained between the user’s body and the
handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this
device should not contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be avoided. Use only the
supplied or an approved antenna.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : zkh
Create Date                     : 2016:09:30 15:55:24+08:00
Modify Date                     : 2016:09:30 15:55:24+08:00
Has XFA                         : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2016:09:30 15:55:24+08:00
Creator Tool                    : Adobe Acrobat Pro 9.0.0
Format                          : application/pdf
Creator                         : zkh
Document ID                     : uuid:29cb4f8c-5a56-4fba-bf8a-53c7f69230f2
Instance ID                     : uuid:55ed3efa-c020-4f45-816f-d2082e5ddc0b
Producer                        : Adobe Acrobat Pro 9.0.0
Page Count                      : 19

EXIF Metadata provided by EXIF.tools