GRAUPNER 16006700 Computer System Graupner HoTT User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2879859
Application ID	o2zZd6Zd++rZ6f2q0qvP7w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	95.17kB (1189588 bits)
Date Submitted	2016-01-21 00:00:00
Date Available	2016-01-21 00:00:00
Creation Date	2015-12-17 15:20:07
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2016-01-13 16:30:06
Document Title	User Manual
Document Creator	Microsoft® Office Word 2007
Document Author:	해외영업부

P1
mz-8 HoTT
◎ GRAUPNER
8th F, 202 Dong, Chunui Techno-Park II, 202,ChunuiDong, Wonmi-Gu,
⑦ 2.4GHz Quad with 6-Axis Gyro
Bucheon-Si, Gyeonggi-do, SOUTH KOREA.
⑧ You can attach camera and video module by
TEL: 070-7863-3675 FAX : 070-7863-3670
choosing option. You can take a video on the radio
E-mail: service@openhobby.com
using Photo & Video button.
mz-8
FUNCTION
Frequency band
2400MHz ~2483.5 MHz
Modulation
FHSS
Transmission output
about 1mW
Temperature range
-10 … +55 ℃
Antenna
Monopole Antenna
Battery
AA Size x 3 pcs
Operating voltage
3.6 … 4.8V
② SPEED : Attitude mode / Rate mode
Output voltage
about 50mA
-> CH5
Dimension
151 x 134 x 63.7 mm
Weight
about 260g (Incl. battery)
Main function and Channel
Basic 4 Channels and added 6 Channels.
6 Channel is as below.
① LED : ON / OFF
-> CH8
1100us / 1900us
1100us / 1900us
③ SNAP : Taking pictures
-> CH9
1100us (1500us nothing)
④ RECORD : Film movies
-> CH9
1900us
⑤ FLIP : Use the button on top left of image (360° FLIP)
-> CH10
1100us / 1900us
now channel 10, later channel 7, (Alpha 150 not active
in autopilot mode as soon as GPS is connected it will be
channel 6 coming home function)
⑥ 3D / EASY : Use the button on top right of image
(180° revolution and additional function)
-> CH6
1100us / 1900us
CH6, when AKRO3D is adjusted in the receiver, for
normal flight mode with GPS (Alpha 150) it will be
autopilot function
P2
Transmitter manual
Operating transmitter
- Power on : Pull Slide switch up
- Power off : Pull Slide switch down
1) Flip Function
3D function is for 180 degrees flight. To operate, use
If you push Flip button, buzzer will ring with 0.5 seconds
same function with Flip.
intervals.
3) Attitude Function
To rotate a full 360 degrees, push Flip button and when
When you push Function button, one short sound rings.
buzzer starts ringing, move stick of transmitter to
This function is attitude control of general quad copters.
maximum position quickly.
4) Rate Function
2) 3D & Easy Function
When you push Function button, two short sound rings.
When you push 3D button, buzzer will ring twice with 1
You can do rotation and normal flight on 3D flight mode
second intervals.
with transmitter. Function is same with 3D helicopter.
Flip Button
MZ-8
3D / Easy Button
Status & Function
Led
Trim
Trim
Speed Button
Camera Snep
Button
Camera Record Button
Light Button
Power Switch
P3
LED Function
Status
Discription
Bind status (No
Buzzer
low beep(1)
Bind Success,
on
low beep(2)
RX receive OK
on
Range Test
fast blinking
Bind range
1) LIGHT ON / OFF Function
Low Voltage
Yellow Led
① When the lights are off, LED stay OFF condition.
low beep(2)
/2sec
High beep(4)
fast blinking
/2sec
High beep(3)
Sensor Warring
② When the lights are on, LED stay ON condition.
Rx Voltage,
Error
（default status）
Green LED
blinking (1s)
bind)
< LED arrangement of transmitter >
Red LED
Temp Error
Receive rate
low, No RX
/2sec
High beep(2)
fast blinking
/2sec
High beep(1)
slow blinking
/2sec
Low beep(1)
Factory Error
2) SPEED Attitude and Rate Function
/2sec
Red Led
① Attitude mode : LED stay ON condition. （ default
status）
Normal
② Rate mode :
LED blinks with one second intervals.
3) Camera function
mode
start
/click
1 blink
low beep(1)
Program mode
Green Led
（default status）
② When movie button is pressed, LED blinks with one
second intervals.
low beep(1)
exit
① When power is switched on, stay On condition.
Program
Servo Reverse
1 blink
(Normal)
(5times)
Servo Reverse
2 blink
(Reverse)
(5times)
ATV 100%
low beep(1)
low beep(2)
High beep(1)
mode
--> Video mode
4) Binding and Transmitter status function.
Red Led
/click
High beep(1)
Trim 0%
Program mode
（Optional feature）
--> Photograph mode
low beep(1)
Trim inc/dec
Fail Safe mode
start
（Status Led）
① Show Power and Binding
② If device is not bound, LED blinks with 0.5 second
2 blink
low beep(2)
Fail safe (trim
1 blink
dn, hold)
(5times)
Fail safe (trim
2 blink
up, fail)
(5times)
low beep(1)
High beep(1)
intervals.
③ If device is bound, LED stay ON condition.
Calibration
mode start
Stick
Calibration
Stick move done
Dead range set
3 blink
3 blink
3 blink
(3times)
(3times)
Dead
blink/3sec
low beep(2)
P4
Program Mode (workable only at Binding condition)
Normal Mode
(1) Condition of Basic Operation
Enter to Program mode : Press two Stick Switch
simultaneously for 2sec.
(1) Basic Operation
- When Power on, the last used memory will be bound to
Receiver.
- In case of No Receiver connection, if you press the
button of left stick for 1sec, it will search Receiver.
- if Receiver is not searched, it will be repeated until find
Receiver, and you can bind with new Receiver by
pressing BIND/LED Switch.
(2) BIND mode
In case of no having receiver, which is already saved in
Release Program mode : Press two Stick Switch
simultaneously for a second.
Indication of Program mode :
once per a second interval
Red Led will be blinked
Program mode : Blink once per a second interval
(2) Saving Data
50pcs of last used Data could be saved.
memory, then you can bind with new receiver by
pressing BIND Switch.
(3) Adjustment of Servo End Position
If Receive Signal is normal, RED LED will be turned On.
In case of Stick Calibration, Default will be 100%. At this
In case of Waiting Receiver or Range warning, RED
value, Customer can adjust trim as below way.
LED will be slow blinked.
- 100% --> 1100us ~ 1900us
At Max. or Min. Position of Stick, adjust Trim Switch
(3) Range Test mode
Range of Trim is available 0% ~ 100% ~ 150%.
Functional switch:
If move to 100% position, High Beep sound will be
Press shortly button of SPEED +
SNAP once.
occurred once.
After Binding with Receiver, if you shortly press this
functional Switch, Range Test mode will operate for
- Red Led will be blinked once per a second interval
90sec.
While operating Range mode, if you shortly press this
Program mode : Blink once per a second interval
switch, Range test mode will be ended.
At Range mode operation, RED LED will blink quickly
(4) Servo Reverse Set
and make buzzer sound.
This is used when change Servo direction.
After 90sec, Beep sound will be occurred one time, and
All sticks are on neutral position, and move the trim
enter to Main Mode.
switch to Max. or Min. Position.
If press Power switch with pressed trim switch to Max. or
(4) Low Battery Voltage warning
Min. position, Normal mode and Reverse mode will be
RED LED will do fast blinking. ( RED LED indicate State)
changed.
At under 3200V, Warning will be announced and at
- Indication of Servo Receiver mode : Red Led will be
3300V, warning will be removed.
blinked once per a second interval
3Cell Alkaline Battery will be used.
- Normal mode : Green LED will be blinked once per a
second interval.
Important Point :
While Binding, Transmitter should always have distance
from the Receiver. At least 1m should have.
Otherwise, it might be connected to Return channel, and
do malfunction.
P5
How to do Stick Calibration
-Reverse mode : Green LED will be blinked twice per a
(1) Enter to Stick Calibration Mode
second interval.
Turn On the Radio, in state of pressing left stick switch.
If enter to Mode, RED LED will blink 3 times.
Program mode : Blink once per a second interval
Stick calibration mode : Blink 3 times per a second
interval
Normal mode : Blink once per a second interval
(Repetition 5times)
(2) Set Stick Calibration
Reverse mode : Blink twice per a second interval
Move all sticks from side to Side and back to middle
(Repetition 5times)
position.
After operated last stick, hold it to middle position for
(5) Fail Safe Set
3Seconds.
Press right stick switch for a second at Program mode.
If Set is done, Red and Green LED will blink 3Times at
Press trim button per channels and select Fail pos mode
same time.
and Hold it.
Whenever press Trim button, Setting-condition will be
Stick calibration mode
transferred to Receiver.
Blink 3 Times per a second interval
If press right-stick switch for a second, Fail safe setting
mode will be ended.
Stick move done
※ after that, it is moved to Dead Range set mode
automatically.
- Indication of Fail Safe mode : RED LED will be blinked
twice per a second interval.
- Pos mode :
If Trim is UP, it is a Fail safe mode, and
(3) Dead range set
This is for keep Neutral position, in case of they have no
Green LED will be blinked twice per a second interval.
accurate Neutral value.
(Repetition 5times)
Dead range set about Neutral position, is set by trim
- Hold mode :
If Trim is Down, it is a Hold mode, and
switch up and down.
Green LED will be blinked once per a second interval.
It can be settable from 1 to 6 steps. ( 0, 2, 4, 6, 8, 10% )
(Repetition 5times)
※ in case of Throttle CH1, there is no spring, Do not set.
( only set for CH2, CH3, CH4 )
Green LED will blink depends on Neutral set steps.
Program mode (Failsafe mode): Blink twice per a
For example, if you set Dead range to 6%, LED will
second interval
blink 4times per a second interval.
Hold mode : Blink once per a second interval (Repetition
Dead range mode
5times)
Blink 3times per a sec interval.
Pos mode : Blink twice per a second interval (Repetition
5times)
Dead range set
Blinks depends of setting value (6 steps)
If set is done, press left stick button for 2 sec.
P6
•
안전규격
(1) KC 인증
Graupner
mz-8 Transmitter
KCC인증번호: MSIP-CRM-sjr-16006700
◎ Notes on environmental protection
This symbol on the product, user
manual or packaging indicates that this
product must not be disposed of with
(2) Conformite Europeenne
Product(s): Graupner
other household waste at the end of its
mz-8 Transmitter,
life. It must be handed over
to the applicable collection point for the
recycling of electrical and electronic
equipment.
(3) FCC Information
The materials are recyclable as marked. By recycling,
Graupner mz-8 Transmitter
material reusing or other forms of scrap usage you are
FCC ID: SNL-16006700
making an important contribution to environmental
FCC Statement
1. This device complies with Part 15 of the FCC
protection.
Batteries and accumulators must be removed from the
Rules. Operation is subject to the following two conditions:
device and disposed of at an appropriate collection point.
(1) This device may not cause harmful interference.
Please inquire if necessary from the local authority for
(2) This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate
the equipment.
• NOTE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- _Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
the appropriate disposal site.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Create Date                     : 2015:12:17 15:20:07+09:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2016:01:13 16:30:06+08:00
Metadata Date                   : 2016:01:13 16:30:06+08:00
Format                          : application/pdf
Creator                         : 해외영업부
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:86e67c6f-523f-40fa-a06e-ee9228b6cd08
Instance ID                     : uuid:8ca19ee2-69a4-4e36-b475-35adb15683c6
Page Count                      : 6
Language                        : ko-KR
Author                          : 해외영업부

EXIF Metadata provided by EXIF.tools