GRAUPNER 16007400 2.4GHz transmitter User Manual mz 4 Manual EN

Download:
Mirror Download [FCC.gov]
Document ID	3204118
Application ID	0Cf3nVVYQcGgbnlmFSJUGw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.37kB (304654 bits)
Date Submitted	2016-11-22 00:00:00
Date Available	2016-11-22 00:00:00
Creation Date	2016-11-18 10:24:59
Document Lastmod	2016-11-18 10:24:59
Document Title	mz-4 Manual_EN
Document Creator	Doro PDF Writer [2.04] [http://j.mp/the_sz]

P1
mz-4 HoTT
◎ GRAUPNER
8th F, 202 Dong, Chunui Techno-Park II, 202,Chunui-Dong, Wonmi-Gu,
Bucheon-Si, Gyeonggi-do, SOUTH KOREA.
TEL: 070-7863-3675 FAX : 070-7863-3670
E-mail: service@openhobby.com
Main function and Channel
FUNCTION
Basic 4 Channels and added 6 Channels.
6 Channel is as below.
1.
LED : ON / OFF
-> CH8
2.
1100us / 1900us
2.4GHz
Mz-4 spec.
Frequency band
Modulation
Transmission output
Temperature range
Antenna
Battery
Operating voltage
Output voltage
Dimension
Weight
2400MHz ~2483.5 MHz
FHSS
about 1mW
-10 … +55 ℃
Monopole Antenna
AAA Size x 3 pcs
3.6 … 4.8V
about 50mA
151 x 134 x 63.7 mm
about 260g (Incl. battery)
P2
Transmitter manual
Operating transmitter
- Power on : Pull Slide switch up
- Power off : Pull Slide switch down
1)Attitude Function
When
hen you push Function button, one short sound rings.
This function is attitude control of general quad copters.
2) Rate Function
When
hen you push Function button, two short sound rings.
You
ou can do rotation and normal flight on 3D flight mode
with transmitter. Function is same with 3D helicopter
Power SW
Trim Button
Status & Function
Bind Switch
P3
LED Function
Status
1) LIGHT ON / OFF Function
Yellow Led
① When the lights are off, LED stay OFF condition.
② When the lights are on, LED stay ON condition.
（default status）
Discription
Red LED
Green LED
Bind status (No
bind)
blinking (1s)
low beep(1)
Bind Success,
on
low beep(2)
RX receive OK
on
Range Test
fast blinking
Low Voltage
fast blinking
Bind range
low beep(2)
/2sec
High beep(4)
/2sec
High beep(3)
/2sec
High beep(2)
/2sec
High beep(1)
/2sec
Low beep(1)
/2sec
2) SPEED Attitude and Rate Function
Red Led
① Attitude mode : LED stay ON condition.（default
condition.
status）
② Rate mode : LED blinks with one second intervals.
Buzzer
Sensor Warring
Error
Rx Voltage,
Temp Error
Receive rate low,
No RX
fast blinking
slow blinking
Factory Error
3) Binding and Transmitter status function.
Red Led （Status Led）
）
① Show Power and Binding
② If device is not bound,
nd, LED blinks with 0.5 second
intervals.
③ If device is bound, LED stay ON condition.
condition
low beep(1)
/click
High beep(1)
/click
Trim inc/dec
Normal mode
Trim 0%
Program mode
start
Program mode
exit
Servo Reverse
(Normal)
Servo Reverse
(Reverse)
Program
mode
low beep(1)
low beep(1)
1 blink
(5times)
2 blink
(5times)
ATV 100%
Fail Safe mode
start
Fail safe (trim dn,
hold)
Fail safe (trim up,
fail)
Stick
Calibration
1 blink
low beep(2)
High beep(1)
2 blink
low beep(2)
1 blink
(5times)
2 blink
(5times)
Calibration mode
start
3 blink
Stick move done
3 blink
(3times)
Dead range set
low beep(1)
3 blink
(3times)
Dead
blink/3sec
low beep(1)
High beep(1)
low beep(2)
(workable
workable only at Binding condition)
condition
P4
Program Mode
Normal Mode
(1) Condition of Basic Operation
(1) Basic Operation
Enter to Program mode : Press two Stick Switch
simultaneously for 2sec.
- When Power on, the
he last used memory will be bound to
Receiver.
- In case of No Receiver connection, if you press the
button of left stick for 1sec, it will search Receiver.
- if Receiver is not searched, it will be repeated until find
Receiver, and you can bind with new Receiver by
pressing BIND/LED Switch.
(2) BIND mode
In case of no having receiver, which is already saved in
memory, then you can bind with new receiver by
pressing BIND Switch.
If Receive Signal is normal, RED LED will be turned On.
In case of Waiting Receiver or Range warning, RED
LED will be slow blinked.
(3) Range Test mode
Functional switch: Press shortly button of SPEED +
SNAP once.
After Binding with Receiver,
eceiver, if you shortly press this
functional Switch, Range Test mode will operate for
90sec.
While operating Range mode, if you shortly press this
switch, Range test mode will be ended.
Att Range mode operation, RED LED will blink quickly
and make buzzer sound.
After 90sec, Beep sound will be occurred one time, and
enter to Main Mode.
(4) Low Battery Voltage warning
RED LED will do fast blinking. ( RED LED indicate State)
At under 3200V, Warning will be announced and at
3300V, warning will be removed.
3Cell Alkaline Battery will be used.
Important Point :
While Binding, Transmitter should always have distance
from the Receiver. At least 1m should have.
Otherwise, it might be connected to Return channel, and
do malfunction.
Release Program mode : Press two Stick Switch
simultaneously for a second.
Indication of Program mode :
once per a second interval
Red Led will be blinked
Program mode : Blink once per a second interval
(2) Saving Data
50pcs of last used Data could be saved.
(3) Adjustment of Servo End Position
In case of Stick Calibration, Default will be 100%. At this
value, Customer can adjust trim as below way.
- 100% -->> 1100us ~ 1900us
At Max. or Min. Position
on of Stick, adjust Trim Switch
Range of Trim is available 0% ~ 100% ~ 150%.
150%
Iff move to 100% position, High Beep sound will be
occurred once.
- Red Led will be blinked once per a second interval
Program mode : Blink once per a second interval
(4) Servo Reverse Set
This is used when change Servo direction.
Allll sticks are on neutral position,
pos
and move the trim
switch to Max. or Min. Position.
tion.
Iff press Power switch with pressed trim switch to Max. or
Min. position, Normal mode and Reverse mode will be
changed.
- Indication of Servo Receiiver mode : Red Led will be
blinked once per a second interval
- Normal mode : Green LED will be blinked once per a
second interval.
P5
-Reverse mode : Green LED will be blinked twice per a
second interval.
How to do Stick Calibration
(1) Enter to Stick Calibration Mode
Turn On the Radio,, in state of pressing left stick switch.
Iff enter to Mode, RED LED will blink 3 times.
Program mode : Blink once per a second interval
Stick calibration mode : Blink 3 times per a second
interval
Normal mode : Blink once per a second interval
(Repetition 5times)
Reverse mode : Blink twice per a second interval
(Repetition 5times)
(5) Fail Safe Set
Press right stick switch for a second at Program mode.
Press trim button per channels and select Fail pos mode
and Hold it.
Whenever press Trim button, Setting-condition
condition will be
transferred to Receiver.
If press right-stick
stick switch for a second, Fail safe setting
mode will be ended.
- Indication of Fail Safe mode : RED LED will be blinked
twice per a second interval.
- Pos mode : If Trim is UP, it is a Fail safe mode, and
Green LED will be blinked twice
ce per a second interval.
(Repetition 5times)
- Hold mode : If Trim is Down, it is a Hold mode, and
Green LED will be blinked once per a second interval.
(Repetition 5times)
Program mode (Failsafe mode): Blink twice per a
second interval
Hold mode : Blink once per a second interval (Repetition
5times)
Pos mode : Blink twice per a second interval (Repetition
5times)
(2) Set Stick Calibration
Move all sticks from side to Side and back to middle
position.
After
fter operated last stick, hold it to middle position for
3Seconds.
If Set is done, Red and Green LED will blink 3Times at
same time.
Stick calibration mode
Stick move done
Blink 3 Times per a second interval
※ after that, it is moved to Dead Range set mode
automatically.
(3) Dead range set
This is for keep Neutral position,
position in case of they have no
accurate Neutral value.
Dead range set about Neutral position, is set by trim
switch up and down.
It can be settable from 1 to 6 steps. ( 0, 2, 4, 6, 8, 10% )
※ in case of Throttle CH1,, there is no spring, Do not set.
( only set for CH2, CH3, CH4 )
Green LED will blink depends on Neutral set steps.
For
or example, if you set Dead range to 6%, LED will
blink 4timess per a second interval.
Dead range mode
Blink 3times per a sec interval.
Dead range set
Blinks depends of setting value (6 steps)
Iff set is done, press left stick button for 2 sec.
• FCC radiation exposure statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment.
P6
안안안안
(1) KC 인증
Graupner mz-8 Transmitter
인인인인
KCC
: MSIP-CRM-sjr-16006700
(2) Conformite Europeenne
Product(s): Graupner mz-8 Transmitter,
(3) FCC Information
Graupner mz-8 Transmitter
FCC ID: SNL-16006700
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate
the equipment.
• NOTE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- _Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
◎ Notes on environmental protection
This symbol on the product, user
manual or packaging indicates that this
product must not be disposed of with
other household waste at the end of its
life. It must be handed over
to the applicable collection point for the
recycling of electrical and electronic
equipment.
The materials are recyclable as marked. By recycling,
material reusing or other forms of scrap usage you are
making an important contribution to environmental
protection.
Batteries and accumulators must be removed from the
device and disposed of at an appropriate collection point.
Please inquire if necessary from the local authority for
the appropriate disposal site.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 6
Creator                         : Doro PDF Writer [2.04] [http://j.mp/the_sz]
Create Date                     : 2016:11:18 10:24:59+08:00
Modify Date                     : 2016:11:18 10:24:59+08:00
Title                           : mz-4 Manual_EN
Subject                         : mz-4 Manual_EN
Author                          : 
Producer                        : 
Keywords                        : mz-4, Manual_EN

EXIF Metadata provided by EXIF.tools