GUANGZHOU BOSMA TECHNOLOGY DS0001 DOOR & WINDOW DETECTOR User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3996783
Application ID	298VPuyDONrxzVZUnWHcDQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.05kB (250567 bits)
Date Submitted	2018-09-09 00:00:00
Date Available	2018-09-09 00:00:00
Creation Date	2018-08-17 06:02:34
Producing Software	Microsoft® Word 2016
Document Lastmod	2018-08-17 06:02:34
Document Title	Users Manual
Document Creator	Microsoft® Word 2016

Door Sensor
Quick Install Guide
Introduction
DS0001 is a wireless magnetic door sensor developed by BOSMA. It has
real-time detection of door and window opening/closing. Modern
design, smooth lines, very good with home decoration. High sensitivity
within 100 meters distance of the host has a very high sensitivity. There
is a code setting between the door magnetic sensor and the host, and its
unique address code is learned to the host when the code is aligned. This
sensor is a separate trigger type. When the location of the magnet and
the emitter moves more than 2cm, the emitter will immediately send an
alarm signal to the alarm host, which will be pushed to the mobile phone
to inform the user, In case the intruder who tries to sneak in from doors
and Windows.
Parameter
Type: DS0001
Wireless range (open area): 200 m
Radio Frequency: 915MHZ
Static Voltage: DC 3.0V (Use a button battery)
Current consumption: Static Current≤10μA
Alarm Current≤25mA
Work Temperature: -10℃ ～ +50℃
Appearance specifications: 60.2*45.7*12mm
Color: White
Feature
Sens
Magnets
or
This product use the principle of magnetic adsorption. When the sensor and the magnet are
separated beyond a certain distance (about 2cm), the associated equipment will receive an
alarm message.
Install Guide
1. Add device
* First, Set up the device with gateway (BOSMA-X1) according to its
instructions and APP guidance to ensure that it is in working state.
⚫
Tap “+”button at the top-right corner to add device
⚫
Wake up equipment, long press the door magnetic switch (pictured).
⚫
Follow the instruction inside the application to bind the device to
your account.
2. Matters needing attention
* Please pay attention to the following situations before installation, so
as to avoid failure use after installation.
⚫
Don not install in the outdoor easily damaged location.
⚫
Do not install to the base is not strong.
⚫
Do not install near the magnetic.
2. Select the installation location
Suit door, window, Drawer and so on that most place is prevented, at
the same time door magnet prevents lampblack, moisture, also apply
to kitchen and toilet.
Tear off the foam tape, then sticker the door magnet to the selected
position, as shown in the figure below.
Caution:
The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 4
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2018:08:17 06:02:34+00:00
Modify Date                     : 2018:08:17 06:02:34+00:00
Document ID                     : uuid:11758AC3-333B-46BF-B24A-A2DC839C5296
Instance ID                     : uuid:11758AC3-333B-46BF-B24A-A2DC839C5296
Creator                         : Microsoft® Word 2016

EXIF Metadata provided by EXIF.tools