GUANGZHOU U and I TECHNOLOGY BS121FE TRUE WIRELESS EARBUDS User Manual
GUANGZHOU U&I; TECHNOLOGY COMPANY LIMITED TRUE WIRELESS EARBUDS Users Manual
User Manual
BS121FE Structure Sketch BS121FE should Wearing Steps: Step① TRUE WIRELESS EARBUDS User Manual TRUE WIRELESS EARBUDS should be used with the compatible devices which support Bluetooth wireless technology. This allows you to make two calls and enjoy the music streaming at any time freely. Please read this user manual carefully before using the EARBUDS, and also read your device’s user manual regarding the Bluetooth function, and pay attention to those important safety and maintenance information. Please keep the headset away from children. Erect headset and place them into the cochlea Step② Slightly rotate headset until it firm 1)MFB(multifunction button) 2)Indicator light and MIC 3)Speaker 4)The charging contact point 5)ON/OFF 6)Charging indicator 7)Micro USB charging port Step③ Specifications V4.2 Bluetooth Version: Bluetooth Profiles Supported: HSP, HFP, A2DP, AVRCP, TWS Audio Decoding Protocol: SBC, AAC Transmission Power: Class 2 Operation Range: Up to 10 meters Frequency Range: 2.4GHz-2.48GHz Battery of Headset: 45mAH Li-polymer Battery X2 Charging Voltage of Headset: 5V Charging Time of Headset: Make the headset to cochlear edge tightly. Status No. Status Headset Performance The Single Pairing The indicator light of headset(R) flashes red and blue alternately. TWS Pairing After TWS pairing successed, the indicator light of right headset alternately flashing red and blue, when the right headset pairing successful with mobile phone, the indicator light flashes blue once every 5 seconds Standby Mode The indicator light of right headset flashes blue once every 5 seconds Call State When in a call, the indicator light of right headset flashes red every 5 seconds Headset Charging State The indicator light of headset is red when being charged, and will turn off automatically after being fully charged Charging Base Charging State About 1hour The indicator light of charging base is red when being charged, and will turn off automatically after being fully charged The indicator light flashes blue for 3 times and then flashes red once every 5 seconds Battery of Base: 460mAH Li-polymer Battery Charging Voltage of Base: 5V Power On State Charging Time of Base: About 2 hours Power Off State 4-5times Low Voltage Alarm The indicator light flashes red once every 20 seconds State Charging Headset Times from Charging Base : Charging Base Supply Power for Headset Music Play Time: About 10 hours Music Playing Time: Up to 2.5 hours Talk Time: Up to 3 hours Standby Time: Up to 100 hours Dimensions of Charging Base(mm): L69×W30×H29.5 Identify according to L&R and wear the EARBODS EARBUDS (R) and EARBUDS EARBODS (L) respectively : About 4.6g Total Weight : About 28.5g *The time mentioned above may vary due to user's operation mode and device settings. Earbuds Headset (L) Note 1: Check the charging device is suit to the headset or not. Note 2: Use only the supplied charger to charge the headset, if use other device may violate the validation or the maintenance article of this product and may cause danger. Note 3: Do not attempt to force open the built-in battery as this could damage the headset. Note 4: A fully charged headset will lose its power automatically if left unused. It is recommended to charge the headset each three months. Note 5: Do not leave the headset in a too hot or too cold condition (best between -10℃ and 50℃) which may affect the headset's operations although it is fully charged. r. Note 6: Do not dispose of the headset into fire or wate Note 7: Please take out of the headsets from the charging base and store it separately if not to use for a long time . Method In OFF MODE, press and hold MFB for 2 seconds to turn on. In ON MODE, press and hold MFB for 5 seconds to turn off. Charging Ways of Earbuds Headset The indicator light of headset is red when being charged, and will turn off automatically after being fully charged Put the headset (L) (R) to the corresponding position in the bottom of the charging base, close the charging base tightly. Charging Ways of Charging Base Use the USB charging cable to charge Earbuds (R) Use the USB cable to connect with mobile phone charger Turning ON/OFF The indicator light flashes red for three times. Dimensions of Headset(mm) : L23.5×W17.1×H22.4 Weight(one headset) Use the USB cable to connect with computer The indicator light of charging base is red when being charged, and will turn off automatically after being fully charged Micro USB charging port Method Pick up the headsets from the charging base to turn on automatically. Put them back and close the charging base to turn off automatically. Music Pause/Playing TWS Pairing 2s On OFF state, press MFB key for 2 seconds to power on and waiting for 10 seconds , the two headsets will enter pairing mode automatically. Two headsets connected with each other after few seconds, the headset (R) alternately flashing red and blue, and then open the phone's bluetooth device to search. Pick up the two headsets from the charging base to power on and waiting for 10 seconds , the two headsets will enter pairing mode automatically. Two headsets connected with each other after few seconds, the headset (R) alternately flashing red and blue, and then open the phone's bluetooth device to search. Do as the above ways: 1 or 2 , after TWS successfully paired: left headset prompts "left channel" and right headset prompts "right channel-pairing" Cell phone begines to search for bluetooth devices (see the user guide of your phone for instructions). Mobile phone to search Bluetooth ON for “BS121FE-R” and select the BS121FE-R “BS121FE-R”. Delete Pairing Records on the Headset On standby mode, shortly press MFB to play music. On music playing state, shortly press MFB to PLAY music, press MFB again to PAUSE music. Maintenance Answering /Ending a Call Headset(R) On standby state or call state, you can answer/end the call by shortly press MFB of the headset(R). Headset(R) Rejecting a call Headset(R) Press and hold MFB of headset(R) for 2 seconds to reject the call, the speaker prompts “beep” twice and “call reject”. The Last Number Redialing Headset(R) Connect Method1: Press and hold MFB for 2 seconds to power on→wait for few seconds, the two headsets connected automatically→the headset paired with the mobile phone that has ever paired after few seconds →reconnected successfully. Method2: Pick up the headsets from charging base to power on→wait for few seconds, the two headsets connected automatically→the headset paired with the mobile phone that has ever paired after few seconds →reconnected successfully. Note: The headset(R)(L)will prompt "connected", left headset prompts "left channel", the right headset prompts "right channel". After connected with mobile phone successfully, the right headset prompts "second device connected”. • Do not use abrasive cleaning solvents to clean the headset. • Do not allow the headset to touch with any sharp objects as this will cause scratching and damage • Please keep headset away from high-temperature, humidity and dust. Common Faults and Exclusion On standby state or call state, shortly press MFB twice to redial the last phone number. The speaker will prompt "beep" twice and "redial". TWS Reconnected On OFF MODE state, press MFB button for 10 seconds (OFF MODE→ON MODE(2 seconds)→Delete pairing records (10 seconds), until hearing the Beep voice for 3 times, and the red/blue light flashes twice at the same time. Two-call Handling Headset(R) (Only support the mobile phone who have function of handling two phones.) When you are answering a call, there is another call coming : 1. Press and hold MFB of headset(R) for 2 seconds to end the current call and answer another one. 2. Shortly press MFB of headset(R) once to answer another call and hold on the current one . 3. After the above operation “2” settled, shortly press MFB of headset(R) to transfer one call to another. Note: All the above operations have to respect the precondition that Phone supported Bluetooth hands free profile V1.5 and Phones are running under call holding function (Network services) from telecom. Faults Reasons Solutions Can not turn on low battery protection Charging headsets for 1 hour Can not turn on by picking up the headset /No indicator light when headset being charged Charging base low battery protection Charging both the headsets and charging base for 1-2 hours No sounds pairing Wrong pairing Pairing again Too many pairing records Delete pairing records according to user manual Charging base without DC power supply doesn’t indicator light when output power charging Check whether the micro USB charging line is plugged or the power switch is on Headsets without indicator light when charging The headsets couldn’t being charged in charging base 1)Checking headset charging interface whether has touched to POGO PIN of charging base and the location is correct or not. 2)Charging for charging base Turning off automatically Low battery Charging headset for 2-3 hours Headset echo Volume is too loud environment is noisy after The two headsets TWS pairing failure/TWS paired successful but can not find the headset(R) or Adjust the volume at phone or change a place Environmental interference Change a place or move to caused or distance between close the headset and mobile headset and mobile is too far Adjusting wearing position of Low voive of the calling Wearing headset is wrong headset party The headset reconnected The charging base without Charging for charging base with mobile phone after put power, the headset will auto turn back to the charging base on and paired Noise in call NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : 3.1-701 Format : application/pdf Title : BS121FE英文说明书(未转曲)2017.3.14(1) Metadata Date : 2017:05:04 13:37:45+08:00 Modify Date : 2017:05:04 13:37:45+08:00 Create Date : 2017:03:16 10:21:12+09:00 Creator Tool : Adobe Illustrator CS6 (Windows) Thumbnail Width : 172 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 16479 bytes, use -b option to extract) Instance ID : uuid:918ab752-d4c1-49a5-bb8b-3e883a22c609 Document ID : xmp.did:CB55DEA7ED09E7119555F54FF51E345D Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : uuid:7a145e79-17d5-4c87-9a66-2351ac24747a Derived From Document ID : xmp.did:C755DEA7ED09E7119555F54FF51E345D Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:BDAD87ABC2C1E111BED484D3A664D8C3, xmp.iid:CB55DEA7ED09E7119555F54FF51E345D History When : 2012:06:29 16:16:04+08:00, 2017:03:16 10:21:10+08:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CS6 (Windows) History Changed : /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 296.999959 Max Page Size H : 209.999929 Max Page Size Unit : Millimeters Font Name : ArialNarrow, ArialMT, Arial-BoldMT, Arial-BoldItalicMT, SimHei, AdobeSongStd-Light Font Family : Arial, Arial, Arial, Arial, 黑体, Adobe 宋体 Std Font Face : Narrow, Regular, Bold, Bold Italic, Regular, L Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type Font Version : Version 2.37, Version 5.06, Version 5.06, Version 5.06, Version 5.01, Version 5.016;PS 5.002;hotconv 1.0.67;makeotf.lib2.5.33168 Font Composite : False, False, False, False, False, False Font File Name : ARIALN.TTF, arial.ttf, arialbd.ttf, ARIALBI.TTF, simhei.ttf, AdobeSongStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black, HKS 92 K, HKS 93 K Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Swatch Groups Colorants Swatch Name: HKS 93 K Swatch Groups Colorants Type : SPOT Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Cyan : 25.000000 Swatch Groups Colorants Magenta : 0.000000 Swatch Groups Colorants Yellow : 10.000600 Swatch Groups Colorants Black : 80.000298 Producer : Adobe PDF library 10.01 Page Count : 3 Creator : Adobe Illustrator(R) 16.0 For : Administrator, Bounding Box : 0 -659 842 604 Container Version : 11 Creator Version : 16EXIF Metadata provided by EXIF.tools