8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 69763 |
| Application ID | gBcLwgW6RPAZ0NNMARBM4g== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 27.95kB (349344 bits) |
| Date Submitted | 1999-11-15 00:00:00 |
| Date Available | 1998-09-24 00:00:00 |
| Creation Date | 2001-05-15 17:52:12 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-05-15 17:52:13 |
| Document Title | 8 |
15” XGA Active Matrix LCD Monitor CrystalPro TFT LCD Monitor User’s Manual Far, lD: DF4LI Ff’iXA Precautions Read all of these instmctions and save them for later use. Follow all warnings and instructions on the product. Product Do not cover or block the vent holes in the case. Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots. They may cause accident fire, electric shock or failure. Disconnect the power plug from the AC outlet if you will not use it for an indefinite period of time. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks, the Do not touch the screen directly with your fingers You may damage screen, and oil from your skin is difficult to move, - Do not apply pressure to the screen. The LCD is very delicate. Power - Use the type of power indicated on the marking label. Plugs - Do not remove any of the prongs of the monitor's three-pronged power plug. » Disconnect the power plug from the AC outlet under following conditions: 0 If you will not use it for an indefinite period timer 0 When the power cord or plug is damaged or frayed, 0 If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. 0 If the product has been dropped or the cabinet has been damaged. 0 If the product exhibits a distinct change in performance, indicating a need for service, Power and extension cords Do not allow anything to rest on the power cord Do not locate this product where persons will walk on the cord. Use the proper power cord with correct attachment plug type, If the power source is 120 V AC, use a power cord that has UL and C-UL approvals If the power source is a 240 V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country's safety regulations, such as VDE for Germany. Do not overload wall outlets or power cords. Ensure that the total of all units plugged into the wall outlet does not exceed 10 arnperes. Ensure that the total ampere ratings on all units plugged into the extension cord is not above the cord's rating. If the power supply cord, which came with your monitor, is to be connected to the PC instead of the wall outlet, this equipment is to be used with UL/TUV approved computers with receptacle rated 100~240V AC, 50/60Hz, 2.0A (minimum). Environment Place the monitor on a flat and leveled surface. Place the monitor in a well-ventilated place. Keep the monitor away from: overly hot, cold or humid places, places directly under sunlight, dusty surroundings, equipment that generate strong magnetic fields Federal Communication Commission Radio Frequency International Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation, This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more the following measures: ~ Reorient / Relocate the receiving antenna, - Increase the separation between the equipment and receiver, ~ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ~ Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 ofthe FCC Rules. Operation is subject to the following two conditions: (i) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice (optional): l The use of non-shielded interface with this equipment is prohibited. 2. A shielded AC power cord must be used with this equipment. If necessary, the user should consult the dealer or an experienced radio / television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful. This booklet is available from the US. Government Printing Office Washington DC, 20402, Stock No‘ 0040007003454, The manufacture is not responsible for any radio or TV interference caused by unauthorized modification of this equipment. It is the responsibility of the user to correct such interference. Caution: To meet FCC limits for a Class B computing device, a shielded signal cable should be used. 1. If you find some parts of the monitor display discolored due to magnetic fields generated by electrical facilities or appliances, turn ofi” the monitor for at least 15 minutes, The degaussing circuit of the monitor will elimina/e the discoloration, 2 Do not remove the monitor on its swivel bore while the power is an, or it may cause discoloration lf discoloration occurs, follow the above mentioned procedure for adjustment. Canadian Department Of Communications Compliance Statement This equipment does not exceed Class B limits per radio noise emissions for a digital apparatus, set out in the Radio Interference Regulation of the Canadian Department of Communications. Operation in a residential area may cause unacceptable interference to radio and TV reception requiring the owner or operator to take whatever steps necessary to correct the interference. Product Description Congratulations on your purchasing this new generation of monitor. Your LCD monitor incorporates high quality display into a small light weighted module. It has power-saving capabilities and emits no X-ray radiation. You will certainly benefit from this monitor in lots of ways; to name some of them, comfort, safety, health, and environmental protection. This LCD monitor incorporates 15" true color active matrix thin-film- transistor (TFT) liquid crystal display to provide superior display performance. A maximum resolution of XGA 1024x768 is ideal for displaying complex graphics and high definition images. Other outstanding designs that enhance this LCD monitor’s performance are Plug & Play compatibility, high performance audio system, USB supporting, portrait display and OSD (On Screen Display) controls Package Contents Included with your LCD monitor are following items: 0 15” TFT liquid crystal monitor with video signal cable 0 A pair of high perfomiance speakers 0 AC power cable 0 Audio cable - Microphone cable - Disk with portrait display sofiware - USB cable 0 User’s manual Product Features High contrast color TFT LCD display support resolution up to XGA 1024x768. Compatible with IBM VGA, VESA, and Macintosh standards High-end detachable audio system provide 3D and base sound performance. Omnidirectional microphone for multimedia usage. Landscape / Portrait display modes provide versatile ways to View the screen image. Power management system conform to VESA DPMS standard. Embedded universal power system. Support DDCl/2B for Plug 84 Play compatibility. Ergonomic identify design for OSD control panel and keyboard space saving. USB (Universal Serial Bus) supporting with 2 downstream ports. Equipped with TCO92 and TCO95 selection, Taking a Look Front View 1. Microphone This is the builtAin microphone. 2. Menu Pressing this button pops up the OSD menus on the screen, and used to select the OSD control options select the OSD function on the screen 3. Reset Pressing this button to reset all OSD control setting back to factory setting. 4. Soft Power Switch When Main Power Switch (on rear side) turns on, this switch control the display system power on or entering Monitor Sleep Mode. 5. + This button is used to adjust the increasing value of the selected OSD control option, 6. — This button is used to adjust the decreasing value of the selected OSD control option. 7. Power LED This LED indicates different status when this unit operates in different modes. 8. Volume Control This is for adjusting the sound volume. 9. Speaker Power LED This indicator illuminates when the audio system power is turned on. 10. Speaker Power Switch This turns the audio system power on or off 1 1. Bass This turns the bass sound effect on or off 12. 3D This turns the surrounding sound effect on or off. 13. Earphone Plug This is for connecting the earphone. Rear View 9959 Main Power Switch This turns the monitor main power on or off. Power Connector This is for connecting the power cable Mic Out This can be connected to the mic-in connector of the computer. USB Up This upstream port is for connecting a USB hub. USB Down Each of these two downstream ports are for connecting a USB device. Audio In This can be connected to the audio-out connector of the computer. Signal Cable This can be connected to the signal connector of the computer. Setting Up WARNING When you disconnect the cord/cables, be sure to hold the connector instead of the wire part. 10 if t . Connect one end of the power cord to the monitor and the other end to the AC outlet. (0) Connect one end of the signal cable to the rear side of computer. Tighten by turning clockwise the two thumb screws to ensure proper grounding (8) Connect either end of the audio cable to the Audio [n connector on the monitor and the other end to the audio-out connector of your computer (9) Connect either end of the other audio cable to the Min: Out connector on the monitor and the other end to the mic-in connector of your computer. (0) Tom on the monitor by pressing the Main Power Switch to the on position (-) (9). Then, turn on the computer. NOTE You have to press the “Sofl Power Switch” on front control side (as section Front View item 4 described) to turn on the LCD monitor. If the display is unsatisfactory, refer to the Controls andAdjustmenzs section 1. if you have USB device need to work, you should connect one end of the USB cable to USB Up port on the monitor and the other end to the USB port of your computer first(©), then connect the USB device to one of the USB Down ports(0). 2. USB Down (0) have 2 ports to support 2 USB devices Display Angle Tilting For viewing clarity, you can tilt the LCD forward (up to 5 degrees) or backward (up to 15 degrees.) CAUTION In order to protect the LCD, be sure to hold the base when you adjust the LCD, and, do not touch the screen 11 Rotating You can change the orientation of the LCD: Landscape in Portrai/ Tilt the LCD fully backward (15 degrees) and rotate it clockwise until it clips into place. Purlrail 10 Landrcape Tilt the LCD fully backward (15 degrees) and rotate it counter clockwise until it clips into place. 12 Controls and Adjustment Adjusting with the OSD Control 0 To Display and Select the BSD Functions: Pressing Menu once pops up the first OSD function. Pressing Menu a second time shows the next OSD control option. Q; - Ta Adjust the Value ofthe Control Option: Pressing + / - button changes the value of the selected OSD control option. After adjusting values, the monitor will automatically save the changes. NOTE The OSD screen will disappear if no input activities are detected for 5 seconds. 13 OSD Control Options - BRIGHTNESS Adjust the brightness using + and — buttons. - CONTRAST Adjust the contrast using + and — buttons. o CLOCK This item is used to decrease the vertical interference. l . Select one display pattern from your computer. Example : Select the pattern from Desktop of Control Panel, and set the Wallpaper item to Field Effect. 2. Use + and 7 buttons on the LCD monitor to decrease the vertical interference to get the optimal display. 3. Reload the pattern and wallpaper settings if needed. o PHASE This item is used to decrease the horizontal interference. 1. Select one display pattern from your computer. Example : Select the pattern from Desktop of Control Panel, and set the Wallpaper item to Field Effect. 14 2, Use + and — buttons on the LCD monitor to decrease the horizontal interference to get the optimal display, 3. Reload the pattern and wallpaper settings if needed. VERTICAL POSITION Pressing + moves the image upward; Pressing — moves the image downward. HORIZONTAL POSITION Pressing + moves the image to the right; Pressing e moves the image to the lefi. RESET Pressing RESET key over 2 seconds to reset all OSD control setting back to the factory setting. 15 Power LED Display & Power Saving General Power Saving Mode When both the Main Power Switch on the rear side and the Soft Power Switch on the front control panel are switch on, this LED lights in green. The LED indicates the different power status with altered LED colors when monitor operates in different modes (see following table). Soft Power Switch & Monitor Sleep Mode The LCD monitor provide the Soft Power Switch feature for users to manually control monitor itself : - Entering sleep mode - Waking up from sleep mode When the LCD monitor on Pic/are Display situation, if you push the Soft Power Switch, the monitor will enter Monitor Sleep Mode (picture will become all dark) immediately Vice versa, when the LCD monitor on Mani/or SIeep Mode, if you push the Soft Power Switch, the monitor will wake up from Monitor Sleep Mode immediately, and display the picture as normal situation, The LED also indicate the Soft Power Switch control status (see following table) 16 Green Action Action Yellow No Action Action No Signal No Action No Action No Signal No Action No Action Troubleshooting The monitor does not respond after you turn on the system. - Check ifthe Main Power Switch and Soft Power Switch ofmonitor are both turned on . 0 Turn off the power and check the monitor’s power cord and signal cable for proper connection, The characters on the screen are dim. - Refer to the Controls and Aafiustmem: section to adjust the brightness. The screen is blank. 0 During operation, the monitor screen may automatically turn off as a result of Power Saving feature. Press any key to see if the screen comes back ~ Refer to the Con/rols and Adjustments section to adjust the brightness. The screen flashes when it‘s initialized. c Tum offthe monitor and tum it on again. WARNING Do not disassemble the monitor. Contact your dealer if needed. I 17 Specifications Type Configuration L5MX»TA-NCO LCD Display 15l0" TFT Active Matrix Panel Display Size 304(H) x 228W) mm PLvel Pitch 10.297(H) x 0.297(V) mm Display Mode 640 x 480 (V: 70Hz. H: 3 I .47KHz) 640 x 480 (V: 75Hz, H: 37.50KHz) 800 x 600 (V: 75Hz, H: 46.88KHZ) 1024 x 768 (V: 75Hz, H: 60.00KHZ) fi—i Max. Resolution XGA 1024 x [68 NJ, Contrast Ratio [50 ' 1 (Typical) Brightness 200 0:va (Typical) Response Time JSO ms Display Color 16M —r Viewing Angle +50“ N -50" (UK), +30“ ~ 40" (U/D) Input Signal Video R.G.B. Analog 0.7V ”km _I sync TTL Positive or Negative Signal Connector 15 Pin Mini D-Sub Front Control Sofi Power Switch, Menu, Reset, Adjust (+, -) Rear Control Main Power Switch OSD Brightness, Contrast, Clock, Phase, H-Posiuon, V-Pnsitiun, Reset Rotation 900 Clockwise Rotate For Portrait Display Plug & Play DDCI / 213 —l 18 Audio System |Speaker 3W / Per Channel |Canrml _IAudio Power Switch, Volume, 3D, Bass Jiunneetw Earphone Plug, Audio—In Microphone Imbedded Omnidirectional Mic. USB 1 Upstream Port, 2 Downstream Ports Power lmbedded AC Input, Universal 90 ~ 264 V J Operating Conditions Temperature (PC ~ 40“C (32°F ~ 104°F) Humidioz ]0% ~ 80% (No Condensation) Altitude Tc 10,000 Feet Storage Candiliarrs Temperature -20°C ~ 60“C (-4“F ~ 140°F) Humidity 10% N 80°41 (N0 Ccndensation) Dimensions 408.6 x 385 x 230.7 mm (Wiih Audio System, Width is 4266 mm) Weight (Net) Efi Certificalmns UL, C UL, FCC-B, TUV/GS, CE, MFR II, EPA, D.N.S.F., lSO924I-3, 1509241-8, TC092/95 (Option) 19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:05:15 17:52:12 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:05:15 17:52:13-04:00 Page Count : 20EXIF Metadata provided by EXIF.tools