Gama Electronics KF340-3 Remote Control Transmitter User Manual 571906

Download:
Mirror Download [FCC.gov]
Document ID	571906
Application ID	ZoluTy7DLnXqri2/zhibSg==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	5.99kB (74883 bits)
Date Submitted	2005-08-16 00:00:00
Date Available	2005-08-16 00:00:00
Creation Date	2005-08-16 11:11:05
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-08-16 11:11:05
Document Title	Microsoft Word - 571906.DOC
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

KF340-3 RF Transmitter
Introduction. Model KF340-3 is a hand held, battery operated, Radio Frequency (RF)
transmitter which operates in conjunction with RF receiver modules. The remote has
momentary switches that upon activation provide relay contact closures on a
receiver/control module. This enables the system to control individual circuits/functions.
Each KF340-3 remote is addressable so that the system can be operated in close
proximity to other systems without interference or cross talk.
Channels:
Frequency:
Operating Temperature Range:
Power Source:
340 MHz
-20 Degrees C to 120 Degrees C
12-Volt DC Battery
Specifications subject to change without notice.
YOU DO NOT NEED AN FCC LICENSE TO OPERATE THIS DEVICE.
HOWEVER, ANY CHANGES OR MODIFICATIONS TO THIS DEVICE WILL
VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.
OPERATION OF THIS DEVICE IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
CAUTION
Batteries. All batteries can cause bodily injury such as burns and/or equipment damage
if conductive material such as jewelry, keys or beaded chains touches the exposed
terminals. These objects may complete an electrical circuit (short circuit) and become
quite hot. Exercise care in handling any charged battery, particularly when placing it
inside a pocket, purse or other container with metal objects.
Care and Safety. To clean the remote, wipe with a soft cloth dampened with water. Do
not use cleaners or solvents on the remote, they can harm the body and leak inside,
causing permanent damage. Battery contacts may be wiped with a dry, lint-free cloth.
If the remote gets wet, remove the battery immediately; dry battery compartment with a
soft cloth to minimize potential damage. Leave housing cover off until the remote is
completely dry. Do not use the remote until it is completely dry.
Installation. Perform the following steps to install the battery and set the unique address
of the remote.
Battery Installation. Using a Phillips-tip screwdriver, remove the one screw from the
remote. Carefully pry apart the front and back housing. Locate the battery compartment
at the bottom of the remote. Install the battery with the negative side towards the spring.
Put the front and back housings together and install the screw.
Code Learning Instructions. Perform the followings steps to program the remote for
the particular receiver/control module.
1. Verify that the DC input power is connected to the receiver.
2. Depress and hold the “LEARN” pushbutton switch on the receiver. Verify that
the “LEARN” LED illuminates, then release the switch.
3. Depress and hold any pushbutton switch on the remote. Verify that the LEARN
LED flashes ON and OFF, and then stays ON, then release the switch on the
remote. This verifies that the receiver has identified the remote being used.
4. After 5-seconds the LEARN LED will extinguish.
5. The system is ready for operation; depress any switch on the remote to verify the
operation.
Operation. The range of the remote will vary depending upon ambient conditions but a
typical range of 20-feet around the receiver can be expected. The remote should be held
in an upright vertical position with the keypad towards the user. For the best possible
reception the user should be facing towards the receiver. There are three switch positions
that are activated by pressing the individual switch positions. As each switch position is
pressed the corresponding relay on the receiver will transfer its contacts. Releasing the
switch position will interrupt the transmission and return the relay of the receiver to the
normal state. During operation, if the reception is intermittent the remote should be
repositioned by moving it to the left or right, up or down, or by the user changing
locations until the optimum reception is achieved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2005:08:16 11:11:05-04:00
Modify Date                     : 2005:08:16 11:11:05-04:00
Page Count                      : 2
Creation Date                   : 2005:08:16 15:11:05Z
Mod Date                        : 2005:08:16 15:11:05Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Administrator
Metadata Date                   : 2005:08:16 15:11:05Z
Creator                         : Administrator
Title                           : Microsoft Word - 571906.DOC

EXIF Metadata provided by EXIF.tools