Gantner Electronic GEA1150002A Access Control Terminal, Access Control Terminal with Biometry User Manual

Gantner Electronic GmbH Access Control Terminal, Access Control Terminal with Biometry GAT Access 6100 Handbuch EN

a href="https://usermanual.wiki/Gantner-Electronic" itemprop="url"> Gantner Electronic >

Contents

User Manual

   GAT Access 6100 GAT Access 6100 F BIO GAT Access 6100 F Enrollment Station GAT TimeAxx 6150 Entry Control and Shower Control Terminals                                       Installation, Operation, Configuration Document version 1.2 GAT Access 6100 GAT Access 6100 F BIO (GAT Access 6100 F + GAT FR 055) GAT Access 6100 F Enrollment Station GAT TimeAxx 6150
GAT Access 6100, GAT Access 6100 F BIO, GAT Access 6100 F Enrollment Station, GAT TimeAxx 6150  www.gantner.com  HB_GAT-ACCESS6100--EN_12 3  General Warning and Safety Instructions  Dear customer, We congratulate you on having selected a product (appliance or software) from GANTNER Electronic GmbH. Our aim is to ensure that our product operates with safety and to your complete satisfaction. To achieve this aim we take this opportunity to familiarize you with the following guidelines:    1.  Installation,  commissioning,  operation  and  maintenance  of  the  purchased  product  must  be  carried  out  in  accordance  with  the instructions, i.e., in accordance with the technical conditions of operation as described in the corresponding product documentation.  2.  Before installation, commissioning, operation or maintenance it is therefore essential that you read the corresponding chapter of this manual and observe its instructions.  3.  If there are still some points on which you are not entirely clear, please do not take a chance. All queries can be clarified by your Gantner company representative, or by ringing the GANTNER Electronic GmbH hotline.  4.  Where not otherwise specifically documented, the appropriate installation, commissioning, operation and maintenance of the product is the customer’s responsibility.  5.  Directly on receipt of the goods, inspect both the packaging and the product itself for any signs of damage. Additionally, check that the delivery is complete and includes all accessories, documentation, auxiliary devices, etc.  6.  If the packaging or product has been damaged in transport, or should you suspect that it may have a fault, the product must not be put into service. In this case, contact your Gantner company representative. They will make every effort to resolve the problem as quickly as possible.  7.  Installation, commissioning and servicing of  our appliances must only be  carried out  by suitably trained  personnel. In particular, electrical connections must only be made by correspondingly qualified specialists. Here, the appropriate installation provisions in accordance with the relevant national Electrical Engineers construction regulations (e.g., ÖVE, [Austrian] VDE, [German]...) must be observed.  8.  Where not otherwise stated, installation and maintenance work on our appliances must be carried out when disconnected from the power supply. This applies in particular to appliances that are normally supplied by low-voltage current.  9.  It is prohibited to alter the device or to remove protective shields and covers.  10.  Do not attempt yourself to repair an appliance after a defect, failure or damage, or to put it back into operation again. In such cases, it is essential you contact either your Gantner company representative or the GANTNER Electronic GmbH hotline.  11.  GANTNER Electronic GmbH accepts no responsibility for any injuries or damage caused as a result of improper use.  12.  Although every care is taken and we are continuously aiming for improvement, we cannot completely exclude the possibility of errors appearing in our documentation. GANTNER Electronic GmbH therefore accepts no responsibility for the completeness or the accuracy of this manual. The right is reserved to make alterations, and we may carry out alterations at any time without giving prior notice.  13.  Should you discover any fault with the product or in its accompanying documentation, or have any suggestions for improvement, you may confidently approach either your Gantner company representative or GANTNER Electronic GmbH directly.  14.  We especially look forward to hearing from you if you just want to tell us that everything is functioning perfectly.  We wish you a successful experience with our product and look forward to welcoming you again as a customer soon.  Contact address / manufacturer: GANTNER Electronic GmbH Montafonerstrasse 8 A - 6780 Schruns/Austria Tel.:   +43 5556 73784 - 0 Fax:   +43 5556 73784 - 8000 Email:   info@gantner.com  Website:    www.gantner.com
Download:
Mirror Download [FCC.gov]
Document ID2733567
Application IDPP37ZG2zteOhweVeEdzhuw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize393.92kB (4923983 bits)
Date Submitted2015-08-31 00:00:00
Date Available2016-02-28 00:00:00
Creation Date2015-08-27 17:56:26
Producing SoftwareMicrosoft® Word 2013
Document Lastmod2015-08-27 17:56:26
Document TitleGAT Access 6100 Handbuch, EN
Document CreatorMicrosoft® Word 2013
Document Author: Roland Weg
FCC ID Filing: NC4-GEA1150002A

Navigation menu