Garmin 01398 LOW POWER COMMUNICATIONS TRANSMITTER User Manual

Garmin International Inc LOW POWER COMMUNICATIONS TRANSMITTER Users Manual

Users Manual

Heart Rate Monitorsubtitle if neededinstructions (EN)Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. ANT™ and ANT+™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Other trademarks and trade names are those of their respective owners.IMAGE January 2009 Printed in Taiwan Part Number 190-00972-91 Rev. A© 2009 Garmin Ltd. or its subsidiaries
EN–2 Heart Rate Monitor InstructionsEN WARNING: See the Important Safety and Product Information in the Garmin product box for product warnings and other important information.Positioning the Heart Rate Monitor The heart rate monitor is on standby and ready to send data. Wear the heart rate monitor directly on your skin, just below your breastplate. It should be snug enough to stay in place during your run.1. Snap one side of the strap to the heart rate monitor module.2. Wet both electrodes on the back of the heart rate monitor strap to create a strong connection between your chest and the transmitter.3. Wrap the strap around your chest, and snap it to the other side of the module. NOTE: The Garmin logo should be right-side up.Heart Rate Monitor Module (Front)Heart Rate Monitor Module (Back)SnapsHeart Rate Monitor Strap (Back)Electrodes
Heart Rate Monitor Instructions EN–3EN4. Turn on the Garmin compatible product, and bring it within range (3 m) of the heart rate monitor. NOTE: If the heart rate data is erratic or does not appear, you may have to tighten the strap on your chest or warm up for 5–10 minutes. Pairing the Heart Rate Monitor Pairing is the connecting of ANT+™ wireless sensors, like your heart rate monitor, with a Garmin compatible product. After you pair the rst time, your Garmin product automatically recognizes your heart rate monitor each time it is activated. NOTE: The pairing instructions differ for each Garmin compatible product. See your owner’s manual.Linking to Fitness EquipmentANT+ technology links your heart rate monitor to tness equipment so you can view your heart rate on the equipment console. Look for the ANT+ Link Here logo on compatible tness equipment. See www something for more linking instructions.
EN–4 Heart Rate Monitor InstructionsENCaring for the Heart Rate Monitor NOTE: Unsnap the module before cleaning the strap.To prolong the life of your heart rate monitor, rinse the strap after every use.Hand wash the strap in cold water with a mild detergent after every ve uses. Do not put the strap in a washing machine or a dryer. Battery InformationWARNING: Do not use a sharp object to remove user-replaceable batteries. Contact your local waste disposal department to properly recycle the batteries.1. Use a small Phillips screwdriver to remove the four screws on the back of the module.2. Remove the cover and replace the battery with the positive side facing up. NOTE: Be careful not to damage or lose the O-ring gasket. 3. Replace the back cover and the four screws.
Heart Rate Monitor Instructions EN–5ENTechnical SpecicationsPhysical size: W × H × D: 11.5 × 1.4 × 0.5 in. (29.3 × 36.5 × 12.5 mm)Weight: 1.6 oz. (45 g)Water resistance: 98 ft. (30 m)Transmission range: approximately 9.8 ft. (3 m) Battery: user-replaceable CR2032 (3 volts) Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste /perchlorate.Battery life: approximately 4.5 years (1 hour per day)Operating temperature: from 23°F to 122°F (from -5°C to 50°C)Radio frequency/protocol: 2.4 GHz ANT wireless communications protocolSystem Compatibility: ANT+Limited WarrantyGarmin’s standard limited warranty applies to this accessory. For more information, see the Important Safety and Product Information in the Garmin product box. This device complies with part 15 of the FCC Rules. Operation is subject to the following two (2) conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received including interference that may cause undesired operation.

Navigation menu