Garmin 02579 Digital Transmission System Transmitter User Manual
Garmin International Inc Digital Transmission System Transmitter
Garmin >
Contents
- 1. User Manual
- 2. User Manual 1
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2526148 |
| Application ID | UKo1ZQ2CfCUTKkbO9NPV6g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 348.51kB (4356356 bits) |
| Date Submitted | 2015-02-06 00:00:00 |
| Date Available | 2015-02-06 00:00:00 |
| Creation Date | 2017-10-19 00:04:01 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-19 00:04:01 |
| Document Title | User Manual |
| Document Creator | AH Formatter V5.3 MR3 (5,3,2011,1116) for Windows (x64) |
TI AL M5APGT00 FI EN Owner’s Manual December 2014 Printed in Taiwan 190-01841-00_0A All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product. Garmin , the Garmin logo, BlueChart , g2 Vision , GPSMAP , and MapSource are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. echoMAP™GMR™, GRID™, GXM™, HomePort™, and SmartMode™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. ® ® ® ® ® The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. iOS is a registered trademark of Cisco Systems, Inc. used under license by Apple Inc. The SDHC logo is a trademark of SD-3C, LLC. NMEA , NMEA 2000 , and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. SiriusXM is a registered trademark of SiriusXM Radio Inc. Wi‑Fi is a registered mark of Wi-Fi Alliance Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. All other trademarks and copyrights are the property of their respective owners. ® ® ® ® ® ® FI EN TI AL ® Introduction.....................................................................1 Front View ................................................................................... 1 Accessing Owner's Manuals on the Chartplotter ........................ 1 Downloading the Manuals .......................................................... 1 Getting More Information ............................................................ 1 Software Update ......................................................................... 1 Loading the New Software on a Memory Card ...................... 1 Updating the Device Software ............................................... 1 GPS Satellite Signals .................................................................. 1 Selecting the GPS Source ..................................................... 1 Customizing the Chartplotter........................................ 1 Home Screen .............................................................................. 1 Adding an Item to Favorites ................................................... 2 Customizing the Layout of a SmartMode or Combination Page .......................................................................................2 Adding a SmartMode Layout ................................................. 2 Adding a Custom Combination Screen .................................. 2 Resetting the Station Layouts ................................................ 2 Setting the Vessel Type .............................................................. 2 Adjusting the Backlight ............................................................... 2 Adjusting the Color Mode ........................................................... 2 Charts and 3D Chart Views........................................... 2 FI EN Navigation Chart and Offshore Fishing Chart ............................. 3 Zooming In and Out Using the Touchscreen ......................... 3 Selecting a Map ..................................................................... 3 Measuring a Distance on the Chart ....................................... 3 Chart Symbols ....................................................................... 3 Showing a Different Chart ...................................................... 3 Creating a Waypoint on the Chart ......................................... 3 Viewing Location and Object Information on a Chart ............ 3 Viewing Details about Navaids .............................................. 4 Navigating to a Point on the Chart ......................................... 4 Premium Charts .......................................................................... 4 Viewing Tide Station Information ........................................... 4 Showing Satellite Imagery on the Navigation Chart .............. 5 Viewing Aerial Photos of Landmarks ..................................... 5 Automatic Identification System .................................................. 5 AIS Targeting Symbols .......................................................... 5 Heading and Projected Course of Activated AIS Targets ...... 5 Showing AIS and MARPA Vessels on a Chart or on a 3D Chart View ............................................................................. 5 Activating a Target for an AIS Vessel .................................... 6 Viewing a List of AIS and MARPA Threats ............................ 6 Setting the Safe-Zone Collision Alarm ................................... 6 AIS Distress Signals .............................................................. 6 Turning Off AIS Reception ..................................................... 6 Chart and 3D Chart View Settings .............................................. 6 Navigation and Fishing Chart Setup ...................................... 7 Waypoints and Tracks Settings on the Charts and Chart Views ..................................................................................... 7 Chart Appearance Settings .................................................... 7 Other Vessels Settings on the Charts and Chart Views ........ 7 Laylines Settings .................................................................... 7 Fish Eye 3D Settings ............................................................. 7 Creating a Waypoint at a Different Location .......................... 8 Marking an SOS Location ...................................................... 9 Viewing a List of all Waypoints .............................................. 9 Editing a Saved Waypoint ...................................................... 9 Moving a Saved Waypoint ..................................................... 9 Browsing for and Navigating to a Saved Waypoint ................ 9 Deleting a Waypoint or an MOB ............................................ 9 Deleting All Waypoints ........................................................... 9 Setting and Following a Direct Course Using Go To ............. 9 Routes ........................................................................................ 9 Creating and Navigating a Route From Your Present Location ................................................................................. 9 Creating and Saving a Route ............................................... 10 Viewing a List of Routes ...................................................... 10 Editing a Saved Route ......................................................... 10 Browsing for and Navigating a Saved Route ....................... 10 Browsing for and Navigating Parallel to a Saved Route ...... 10 Deleting a Saved Route ....................................................... 10 Deleting All Saved Routes ................................................... 10 Auto Guidance .......................................................................... 10 Setting and Following an Auto Guidance Path .................... 10 Creating and Saving an Auto Guidance Path ...................... 10 Adjusting a Saved Auto Guidance Path ............................... 11 Canceling an Auto Guidance Calculation in Progress ......... 11 Setting a Timed Arrival ......................................................... 11 Auto Guidance Line Configurations ..................................... 11 Tracks ....................................................................................... 12 Showing Tracks ................................................................... 12 Setting the Color of the Active Track ................................... 12 Saving the Active Track ....................................................... 12 Viewing a List of Saved Tracks ............................................ 12 Editing a Saved Track .......................................................... 12 Saving a Track as a Route ................................................... 12 Browsing for and Navigating a Recorded Track .................. 12 Deleting a Saved Track ........................................................ 12 Deleting All Saved Tracks .................................................... 12 Retracing the Active Track ................................................... 12 Clearing the Active Track ..................................................... 12 Managing the Track Log Memory During Recording ........... 12 Configuring the Recording Interval of the Track Log ........... 12 Stopping Navigation ................................................................. 12 Synchronizing User Data Across the Garmin Marine Network . 12 Deleting All Saved Waypoints, Routes, and Tracks ................. 12 TI AL Table of Contents Navigation with a Chartplotter...................................... 8 Basic Navigation Questions ........................................................ 8 Destinations ................................................................................ 8 Searching for a Destination by Name .................................... 8 Selecting a Destination Using the Navigation Chart .............. 8 Searching for a Marine Services Destination ......................... 8 Searching for a Volvo Penta® Dealer .................................... 8 Waypoints ................................................................................... 8 Marking Your Present Location as a Waypoint ...................... 8 Table of Contents Sailing Features............................................................ 13 Setting the Vessel Type ............................................................ 13 Sail Racing ................................................................................ 13 Starting Line Guidance ........................................................ 13 Setting the Starting Line ...................................................... 13 Using the Starting Line Guidance ........................................ 13 Starting the Race Timer ....................................................... 13 Stopping the Race Timer ..................................................... 13 Setting the Distance between the Bow and the GPS Antenna ................................................................................13 Laylines Settings ....................................................................... 13 Setting the Keel Offset .............................................................. 13 Sailboat Autopilot Operation ..................................................... 14 Wind Hold ............................................................................ 14 Tack and Gybe ..................................................................... 14 Sonar............................................................................. 14 Sonar Views .............................................................................. 14 Traditional Sonar View ......................................................... 14 DownVü Sonar View ............................................................ 15 SideVü Sonar View .............................................................. 15 Split-Zoom Sonar View ........................................................ 15 Split-Frequency Sonar View ................................................ 15 Changing the Sonar View .................................................... 15 TI AL Enabling Shadow Drive™ .................................................... 23 Engaging the Autopilot ............................................................. 23 Adjusting the Heading with the Helm ................................... 24 Adjusting the Heading with the Chartplotter in Step Steering Mode .................................................................................... 24 Steering Patterns ...................................................................... 24 Following the U-Turn Pattern ............................................... 24 Setting Up and Following the Circles Pattern ...................... 24 Setting Up and Following the Zigzag Pattern ...................... 24 Following the Williamson Turn Pattern ................................ 24 Following an Orbit Pattern ................................................... 24 Setting Up and Following the Cloverleaf Pattern ................. 24 Setting Up and Following a Search Pattern ......................... 24 Cancelling a Steering Pattern .............................................. 24 Digital Selective Calling............................................... 24 Networked Chartplotter and VHF Radio Functionality .............. 24 Turning On DSC ....................................................................... 25 DSC List .................................................................................... 25 Viewing the DSC List ........................................................... 25 Adding a DSC Contact ......................................................... 25 Incoming Distress Calls ............................................................ 25 Navigating to a Vessel in Distress ....................................... 25 Man-Overboard Distress Calls Initiated from a VHF Radio . 25 Man-Overboard and SOS Distress Calls Initiated from the Chartplotter .......................................................................... 25 Position Tracking ...................................................................... 25 Viewing a Position Report .................................................... 25 Navigating to a Tracked Vessel ........................................... 25 Creating a Waypoint at the Position of a Tracked Vessel .... 25 Editing Information in a Position Report .............................. 25 Deleting a Position-Report Call ............................................ 25 Viewing Vessel Trails on the Chart ...................................... 25 Individual Routine Calls ............................................................ 26 Selecting a DSC Channel .................................................... 26 Making an Individual Routine Call ....................................... 26 Making an Individual Routine Call to an AIS Target ............ 26 EN Creating a Waypoint on the Sonar Screen ............................... 15 Pausing the Sonar Display ....................................................... 15 Viewing Sonar History .............................................................. 15 Sonar Sharing ........................................................................... 15 Selecting a Sonar Source .................................................... 16 Renaming a Sonar Source .................................................. 16 Adjusting the Level of Detail ..................................................... 16 Adjusting the Color Intensity ..................................................... 16 Adjusting the Range of the Depth or Width Scale .................... 16 Setting the Zoom Level on the Sonar Screen ........................... 16 Setting the Scroll Speed ........................................................... 16 Sonar Frequencies ................................................................... 17 Selecting Frequencies ......................................................... 17 Creating a Frequency Preset ............................................... 17 Turning On the A-Scope ........................................................... 17 Selecting the Transducer Type ................................................. 17 Sonar Setup .............................................................................. 17 Sonar Settings ..................................................................... 17 Sonar Noise Rejection Settings ........................................... 17 Sonar Appearance Settings ................................................. 18 Sonar Alarm Settings ........................................................... 18 Advanced Sonar Settings .................................................... 18 Transducer Installation Settings .......................................... 18 Sonar Recordings ..................................................................... 18 Recording the Sonar Display ............................................... 18 Stopping the Sonar Recording ............................................. 18 Deleting a Sonar Recording ................................................. 18 Playing Sonar Recordings ................................................... 19 Radar ............................................................................. 19 FI Radar Display Modes ............................................................... 19 Changing the Radar Mode ....................................................... 19 Transmitting Radar Signals ...................................................... 19 Adjusting the Radar Range ...................................................... 19 Tips for Selecting a Radar Range ........................................ 19 Zooming In and Out of the Radar Screen ................................. 19 Marking a Waypoint on the Radar Screen ................................ 19 Sentry Mode ............................................................................. 19 Enabling Timed Transmit ..................................................... 19 Setting the Standby and Transmit Times ............................. 20 Enabling a Guard Zone ........................................................ 20 Defining a Circular Guard Zone ........................................... 20 Defining a Partial Guard Zone ............................................. 20 Radar Targeting and MARPA ................................................... 20 MARPA Targeting Symbols ................................................. 20 Assigning a MARPA Tag to an Object ................................. 20 Viewing a List of AIS and MARPA Threats .......................... 20 Showing AIS Vessels on the Radar Screen ........................ 20 VRM and EBL ...................................................................... 20 Radar Overlay ........................................................................... 21 Radar Overlay and Chart Data Alignment ........................... 21 Showing the Radar Overlay ................................................. 21 Setting a Custom Park Position ................................................ 21 Enabling and Adjusting a Radar No Transmit Zone ................. 21 Stopping the Transmission of Radar Signals ........................... 21 Optimizing the Radar Display ................................................... 21 Radar Gain and Clutter ........................................................ 21 Echo Trails ........................................................................... 22 Radar Display Settings ........................................................ 22 Radar Appearance Settings ................................................. 23 Front-of-Boat Offset ............................................................. 23 Selecting a Different Radar Source .......................................... 23 Autopilot........................................................................ 23 Opening the Autopilot Screen ................................................... 23 Autopilot Screen ....................................................................... 23 Adjusting the Step Steering Increment ................................ 23 Setting the Power Saver ...................................................... 23 ii Gauges and Graphs..................................................... 26 Viewing the Gauges ................................................................. 26 Changing the Data Shown in a Gauge ................................ 26 Customizing Engine Gauge and Fuel Gauge Limits ............ 26 Viewing Engine and Fuel Gauges ............................................ 26 Selecting the Number of Engines Shown in Gauges ........... 26 Customizing the Engines Shown in Gauges ........................ 26 Enabling Status Alarms for Engine Gauges ........................ 26 Enabling Some Engine Gauge Status Alarms ..................... 26 Setting the Fuel Alarm .............................................................. 26 Setting the Fuel Capacity of the Vessel ............................... 26 Synchronizing the Fuel Data with the Actual Vessel Fuel ... 27 Viewing the Wind Gauges ........................................................ 27 Configuring the Sailing Wind Gauge .................................... 27 Configuring the Speed Source ............................................. 27 Configuring the Heading Source of the Wind Gauge ........... 27 Customizing the Close-Hauled Wind Gauge ....................... 27 Viewing Trip Gauges ................................................................ 27 Resetting Trip Gauges ......................................................... 27 Viewing Graphs ........................................................................ 27 Setting the Graph Range and Time Scales ......................... 27 Tide, Current, and Celestial Information.................... 27 Tide Station Information ............................................................ 27 Current Station Information ....................................................... 27 Celestial Information ................................................................. 27 Viewing Tide Station, Current Station, or Celestial Information for a Different Date ................................................................... 28 Viewing Information for a Different Tide or Current Station ...... 28 Viewing Almanac Information from the Navigation Chart ......... 28 Table of Contents Viewing Messages .................................................................... 28 Sorting and Filtering Messages ................................................ 28 Saving Messages to a Memory Card ........................................ 28 Clearing all of the Messages .................................................... 28 Media Player................................................................. 28 Device Configuration................................................... 34 Turning On the Chartplotter Automatically ............................... 34 System Settings ........................................................................ 34 Station Settings .................................................................... 34 Viewing System Software Information ................................. 34 Viewing the Event Log ......................................................... 34 Preferences Settings ................................................................ 34 Units Settings ....................................................................... 35 Navigation Settings .............................................................. 35 Communications Settings ......................................................... 36 NMEA 0183 Settings ............................................................ 36 NMEA 2000 Settings ............................................................ 36 Garmin Marine Network ....................................................... 36 Setting Alarms .......................................................................... 36 Navigation Alarms ................................................................ 36 System Alarms ..................................................................... 36 Setting the Fuel Alarm ......................................................... 36 Setting Weather Alarms ....................................................... 36 My Vessel Settings ................................................................... 36 Setting the Keel Offset ......................................................... 36 Setting the Water Temperature Offset ................................. 37 Calibrating a Water Speed Device ....................................... 37 Setting the Vessel Type ....................................................... 37 Other Vessels Settings ............................................................. 37 Restoring the Original Chartplotter Factory Settings ................ 37 EN Opening the Media Player ........................................................ 28 Icons .................................................................................... 28 Selecting the Media Source ...................................................... 28 Playing Music ............................................................................ 28 Browsing for Music ............................................................... 28 Setting a Song to Repeat ..................................................... 28 Setting All Songs to Repeat ................................................. 28 Setting Songs to Shuffle ...................................................... 28 Listening to the Radio .......................................................... 28 Opening the MTP Source .................................................... 29 Adjusting the Volume ................................................................ 29 Enabling and Disabling Zones ............................................. 29 Muting the Media Volume .................................................... 29 Scanning VHF Channels .......................................................... 29 Adjusting the VHF Squelch ....................................................... 29 SiriusXM® Satellite Radio ........................................................ 29 Locating a SiriusXM Radio ID .............................................. 29 Activating a SiriusXM Subscription ...................................... 29 Customizing the Channel Guide .......................................... 29 Saving a SiriusXM Channel to the Presets List ................... 29 Unlocking SiriusXM Parental Controls ................................. 29 Setting the Device Name .......................................................... 30 Networked Video Devices ......................................................... 33 Using Video Presets on Networked Video Cameras ........... 33 Camera Settings .................................................................. 33 Video Settings ...................................................................... 33 Associating the Camera to a Video Source ......................... 33 Video Camera Movement Control ........................................ 33 Creating a Combination with Video Functions .......................... 34 Configuring the Video Appearance ........................................... 34 Configuring the PC Display ....................................................... 34 Exiting PC Display Mode ..................................................... 34 TI AL Warning Manager......................................................... 28 SiriusXM Weather......................................................... 30 FI SiriusXM Equipment and Subscription Requirements .............. 30 Weather Data Broadcasts ......................................................... 30 Changing the Weather Chart .................................................... 30 Viewing Precipitation Information ............................................. 30 Precipitation Views ............................................................... 30 Storm Cell and Lightning Information ....................................... 30 Hurricane Information ............................................................... 30 Weather Warnings and Weather Bulletins ................................ 30 Forecast Information ................................................................. 31 Viewing Forecast Information for Another Time Period ....... 31 Weather Fronts and Pressure Centers ................................ 31 Viewing a Marine Forecast or an Offshore Forecast ........... 31 City Forecasts ...................................................................... 31 Viewing Sea Conditions ............................................................ 31 Surface Winds ...................................................................... 31 Wave Height, Wave Period, and Wave Direction ................ 31 Viewing Forecast Sea Conditions Information for Another Time Period .......................................................................... 31 Viewing Fishing Information ...................................................... 31 Surface Pressure and Water Temperature Data ................. 31 Forecasting Fish Locations .................................................. 32 Changing the Sea Surface Temperature Color Range ........ 32 Visibility Information .................................................................. 32 Viewing Forecast Visibility Information for Another Time Period ................................................................................... 32 Viewing Buoy Reports .............................................................. 32 Viewing Local Weather Information near a Buoy ................. 32 Creating a Waypoint on a Weather Chart ................................. 32 Weather Overlay ....................................................................... 32 Turning On the Weather Overlay on a Chart ....................... 32 Weather Overlay Settings on the Navigation Chart ............. 32 Weather Overlay Settings on the Fishing Chart .................. 32 Viewing Weather Subscription Information ............................... 32 Viewing Video............................................................... 32 Selecting a Video Source ......................................................... 33 Alternating Among Multiple Video Sources ......................... 33 Table of Contents Communication with Wireless Devices...................... 37 Setting Up the Wi‑Fi® Wireless Network .................................. 37 Connecting a Wireless Device to the Chartplotter .................... 37 Changing the Wireless Channel ............................................... 38 Changing the Wi‑Fi Host ........................................................... 38 Wireless Remote Control .......................................................... 38 Pairing the Wireless Remote Control With the Chartplotter .......................................................................... 38 Turning On and Off the Remote Backlight ........................... 38 Disconnecting the Remote from All Chartplotters ................ 38 Using the Garmin Helm Application with the Chartplotter ........ 38 Chartplotter Data Management ................................... 38 Copying Waypoints, Routes, and Tracks from HomePort to a Chartplotter ............................................................................... 38 Selecting a File Type for Third-Party Waypoints and Routes ... 38 Copying Data from a Memory Card .......................................... 38 Copying Waypoints, Routes, and Tracks to a Memory Card .... 38 Copying Waypoints, Routes, and Tracks to or from all Chartplotters on the Network .................................................... 38 Copying Built-In Maps to a Memory Card ................................. 38 Backing Up Data to a Computer ............................................... 38 Restoring Backup Data to a Chartplotter .................................. 39 Saving System Information to a Memory Card ......................... 39 Appendix....................................................................... 39 Registering Your Device ........................................................... 39 Digital Switching ....................................................................... 39 Rotating the GRID Joystick ....................................................... 39 Cleaning the Screen ................................................................. 39 Screenshots .............................................................................. 39 Capturing Screenshots ........................................................ 39 iii Copying Screenshots to a Computer ................................... 39 Troubleshooting ........................................................................ 39 My device will not acquire GPS signals ............................... 39 My device will not turn on or keeps turning off ..................... 39 My device is not creating waypoints in the correct location ................................................................................. 40 NMEA 0183 Information ........................................................... 40 NMEA 2000 PGN Information ................................................... 40 Software License Agreement ................................................... 40 FI EN TI AL Index.............................................................................. 42 iv Table of Contents Introduction Software Update The Garmin website at www.garmin.com presents up-to-date information about your product. The support pages will provide answers to frequently asked support questions, and you can download software and chart updates. There is also contact information to Garmin support should you have any questions. ® Front View You may need to update the device software when you install the device or add an accessory to the device. Loading the New Software on a Memory Card 1 Insert a memory card into the card slot on the computer. 2 Go to www.garmin.com/support/software/marine.html. 3 Select Download next to Garmin Marine Network with SD card. Read and agree to the terms. Select Download. Select Run. Select the drive associated with the memory card, and select Next > Finish. TI AL WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Updating the Device Software Power key Automatic backlight sensor Beeper SD or microSD™* memory card slot Touchscreen *Seven-inch models have microSD card slots. FI 1 Select Info > Owner's Manual. 2 Select a manual. 3 Select Open. Accessing Owner's Manuals on the Chartplotter EN À Á Â Ã Ä Downloading the Manuals You can get the latest owner's manual and translations of manuals from the web. TIP: To quickly open this web page, scan this code: 2 Download the manual. Getting More Information If you have any questions about your device, you can contact Garmin Product Support. The website, www.garmin.com/support, offers many different troubleshooting tips to help resolve most issues and answer most questions. • Frequently-asked questions (FAQs) • Software updates • Owner's and installation manuals • Service alerts • Video • Contact numbers and addresses Introduction Before you can update the software, you must obtain a software-update memory card or load the latest software onto a memory card. 1 Turn on the chartplotter. 2 After the home screen appears, insert the memory card into the card slot. NOTE: In order for the software update instructions to appear, the device must be fully booted before the card is inserted. 3 Follow the on-screen instructions. 4 Wait several minutes while the software update process completes. The device returns to normal operation after the software update process is complete. 5 Remove the memory card. NOTE: If the memory card is removed before the device restarts fully, the software update is not complete. GPS Satellite Signals When you turn on the chartplotter, the GPS receiver must collect satellite data and establish the current location. When the chartplotter acquires satellite signals, appears at the top of the Home screen. When the chartplotter loses satellite signals, disappears and a flashing question mark appears over on the chart. For more information about GPS, go to www.garmin.com /aboutGPS. Selecting the GPS Source You can select your preferred source for GPS data, if you have more than one GPS source. 1 Select Settings > System > GPS > Source. 2 Select the source for GPS data. Customizing the Chartplotter Home Screen The chartplotter home screen provides access to all of the features in the chartplotter. The features are dependant on the accessories you have connected to the chartplotter. You may not have all of the options and features discussed in this manual. The categories along the right of the screen provide quick access to the main features of your chartplotter. For example, the Sonar category displays the views and pages related to the sonar feature. You can save items you commonly access to the Favorites category. Adding an Item to Favorites 1 From the home screen, select a category from the right. 2 Hold a button. Customizing the Layout of a SmartMode or Combination Page FI You can customize the layout and data shown in the combination pages and SmartMode layouts. When you change the layout of a page in a display you are interacting with, the change appears only on that display, except for the SmartMode name and symbol. When you change the SmartMode name or symbol for the layout, the new name or symbol appears on all displays in the station. 1 Open a page to customize. 2 Select Menu. 3 Select Edit Layout or Edit Combo. 4 Select an option: • To change the name, select Name or Name & Symbol > Name, enter a new name, and select Done. • To change the SmartMode symbol, select Name & Symbol > Symbol, and select a new symbol. • To change the number of functions shown, select Functions, and select a number. • To change the function of the portion of the screen, select the area to change, and select a function from the list on the right. • To change the vertical or horizontal split orientation of a multi-function display, select Split, and select an option. • To change how data appears on the page, select Overlays, and select an option. • To change the type of data shown, select Overlays, select a data field, and select the new data type. Adding a SmartMode Layout You can add SmartMode layouts to suit your needs. Each customization made to one SmartMode layout for the home screen in a station appears on all displays in the station. 1 From the home screen, select SmartMode™ > Menu > Add Layout. 2 Select an option: • To change the name, select Name & Symbol > Name, enter a new name, and select Done. Adding a Custom Combination Screen You can create a custom combination screen to suit your needs. 1 Select Combos > Menu > Add Combo. 2 Select an option: • To change the name, select Name, enter a new name, and select Done. • To change the number of functions shown, select Functions, and select a number. • To change the function of the portion of the screen, select the area to change, and select a function from the list on the right. • To change the vertical or horizontal split orientation of a multi-function display, select Split, and select an option. • To change how data appears on the page, select Overlays, and select an option. • To change the type of data shown, select Overlays, select a data field, and select the new data type. EN The item is added to the Favorites home screen category. • To change the symbol, select Name & Symbol > Symbol, and select a new symbol. • To change the number of functions shown, select Functions, and select a number. • To change the function of the portion of the screen, select the area to change, and select a function from the list on the right. • To change the vertical or horizontal split orientation of a multi-function display, select Split, and select an option. • To change how data appears on the page, select Overlays, and select an option. • To change the type of data shown, select Overlays, select a data field, and select the new data type. TI AL All of the options along the bottom of the home screen are visible on all other screens, except for the Settings button. The Settings button is accessible only from the home screen. When viewing another screen, you can return to the home screen by selecting Home. When multiple displays are installed on the Garmin Marine Network, you can group them together into a station. A station enables the displays to work together, instead of as several separate displays. When you select Home on one display, each display in the station returns to the home screen. You can customize the layout of the pages on each display, making each page different on each display. When you change the layout of a page in one display, the changes appear on only that display. When you change the name and symbol of the layout, those changes appear on all displays in the station, to maintain a consistent appearance. The SmartMode™ items are geared toward an activity, such as cruising or docking. When a SmartMode button is selected from the home screen, each display in the station can show unique information. For example, when Cruising is selected from the home screen, one display can show the navigation chart and another display can show the radar screen. Resetting the Station Layouts You can restore the factory default layouts for all stations. Select Settings > System > Station Information > Reset Stations. Setting the Vessel Type You can select your boat type to configure the chartplotter settings and to use features customized for your boat type. 1 Select Settings > My Vessel > Vessel Type. 2 Select Powerboat or Sailboat. Adjusting the Backlight 1 Select Settings > System > Beeper and Display > Backlight. TIP: Press from any screen to open the backlight settings. 2 Select an option: • Adjust the backlight level. • Select Auto. Adjusting the Color Mode 1 Select Settings > System > Beeper and Display > Color Mode. TIP: Press from any screen to access the color settings. 2 Select an option. Charts and 3D Chart Views The charts and 3D chart views that are available depend on the map data and accessories used. You can access the charts and 3D chart views by selecting Charts. Charts and 3D Chart Views • When you are offshore, select BlueChart® g2. Measuring a Distance on the Chart 1 From a chart or the Radar overlay, select a location. 2 Select Measure Distance. A push pin appears on the screen at your present location. The distance and angle from the pin is listed in the upper-left corner. TIP: To reset the pin and measure from the current location of the cursor, select Set Reference. Chart Symbols This table contains some of the common symbols you might see on the detailed charts. Description TI AL Icon Buoy Information Marine services Tide station Current station Overhead photo available Perspective photo available Other features common to most charts include depth contour lines, intertidal zones, spot soundings (as depicted on the original paper chart), navigational aids and symbols, obstructions, and cable areas. EN Navigation Chart: Shows navigation data available on your preloaded maps and from supplemental maps, if available. The data includes buoys, lights, cables, depth soundings, marinas, and tide stations in an overhead view. Perspective 3D: Provides a view from above and behind the boat (according to your course) and provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and is beneficial when trying to identify entry and exit routes in unfamiliar harbors or anchorages. Mariner’s Eye 3D: Shows a detailed, three-dimensional view from above and behind the boat (according to your course) and provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and when trying to identify entry and exit routes in unfamiliar harbors or anchorages. NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are available with premium charts, in some areas. Fish Eye 3D: Provides an underwater view that visually represents the sea floor according to the chart information. When a sonar transducer is connected, suspended targets (such as fish) are indicated by red, green, and yellow spheres. Red indicates the largest targets and green indicates the smallest. Fishing Chart: Provides a detailed view of the bottom contours and depth soundings on the chart. This chart removes navigational data from the chart, provides detailed bathymetric data, and enhances bottom contours for depth recognition. This chart is best for offshore deep-sea fishing. NOTE: The offshore Fishing chart is available with premium charts, in some areas. Radar Overlay: Superimposes radar information on the Navigation chart or the Fishing chart, when the chartplotter is connected to a radar. This feature is not available with all models. Navigation Chart and Offshore Fishing Chart FI NOTE: The offshore Fishing chart is available with premium charts, in some areas. The Navigation and Fishing charts allow you to plan your course, view map information, and follow a route. The Fishing chart is for offshore fishing. To open the Navigation chart, select Charts > Nav Chart. To open the Fishing chart, select Charts > Fishing Chart. Zooming In and Out Using the Touchscreen You can quickly zoom in and out of many screens, such as the charts and sonar views. • Pinch two fingers together to zoom out. • Spread two fingers apart to zoom in. Selecting a Map If your product has both BlueChart g2 and LakeVü™ HD built-in maps, you can select which map to use. Not all models have both types of built-in maps. 1 From the Navigation chart, select Menu > Built-In Map. 2 Select an option: • When you are on an inland lake, select LakeVü™ HD. Charts and 3D Chart Views ® Showing a Different Chart 1 From a combination screen or SmartMode layout with a chart, select Menu > Chart Menu > Change Chart. 2 Select a chart or 3D chart view. Creating a Waypoint on the Chart 1 From a chart or a 3D chart view, select a location or object. A list of options appears along the right side of the chart. The options that appear vary based on the location or object you selected. 2 Select Create Waypoint. Viewing Location and Object Information on a Chart You can view information about a location or an object on the Navigation chart or the Fishing chart. NOTE: The offshore Fishing chart is available with premium charts, in some areas. 1 From the Navigation chart or Fishing chart, select a location or object. A list of options appears along the right side of the chart. The options that appear vary based on the location or object you selected. 2 Select an option: • To navigate to the selected location, select Navigate To. • To mark a waypoint at the cursor location, select Create Waypoint. • To view the distance and bearing of the object from your current location, select Measure Distance. The distance and bearing appear on the screen. Select Select to measure from a location other than your current location. • To view tide, current, celestial, chart notes, or local services information near the cursor, select Information. From the Navigation chart, Fishing chart, Perspective 3D chart view, or Mariner’s Eye 3D chart view, you can view details about various types of navigation aids, including beacons, lights, and obstructions. NOTE: The offshore Fishing chart is available with premium charts, in some areas. NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are available with premium charts, in some areas. 1 From a chart or 3D chart view, select a navaid. 2 Select the name of the navaid. Navigating to a Point on the Chart CAUTION The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. Viewing Tide Station Information on the chart indicates a tide station. You can view a detailed graph for a tide station to help predict the tide level at different times or on different days. NOTE: This feature is available with premium charts, in some areas. 1 From the Navigation chart or Fishing chart, select a tide station. Tide direction and tide level information appear near . 2 Select the station name. FI EN NOTE: The offshore Fishing chart is available with premium charts, in some areas. NOTE: Auto Guidance is available with premium charts, in some areas. 1 From the Navigation chart or Fishing chart, select a location. 2 If necessary, select Select. 3 Select Navigate To. 4 Select an option: • To navigate directly to the location, select Go To. • To create a route to the location, including turns, select Route To. • To use Auto Guidance, select Auto Guidance. 5 Review the course indicated by the magenta line. NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height. 6 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. Fishing Charts: Shows the chart with enhanced bottom contours and without navigational data. This chart works well for offshore deep-sea fishing. High Resolution Satellite Imagery: Provides high-resolution satellite images for a realistic view of the land and water on the Navigation chart (Showing Satellite Imagery on the Navigation Chart). Aerial Photos: Shows marinas and other navigationally significant aerial photos to help you visualize your surroundings (Viewing Aerial Photos of Landmarks). Detailed Roads and POI data: Shows detailed road and point of interest (POI) data, which includes highly detailed coastal roads and POIs such as restaurants, lodging, and local attractions. Auto Guidance: Uses specified safe depth, safe height, and chart data to determine the best course to your destination. Auto Guidance is available when you navigate to a destination using Guide To. TI AL Viewing Details about Navaids Premium Charts CAUTION The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. NOTE: Not all models support all charts. Optional premium charts, such as BlueChart g2 Vision , allow you to get the most out of your chartplotter. In addition to detailed marine charting, premium charts may contain these features, which are available in some areas. Mariner’s Eye 3D: Provides a view from above and behind the boat for a three-dimensional navigation aid. Fish Eye 3D: Provides an underwater, three-dimensional view that visually represents the sea floor according to the information on the chart. ® Animated Tide and Current Indicators NOTE: This feature is available with premium charts, in some areas. You can view indicators for animated tide station and current direction on the Navigation chart or the Fishing chart. You must also enable animated icons in the chart settings (Showing and Configuring Tides and Currents). An indicator for a tide station appears on the chart as a vertical bar graph with an arrow. A red arrow pointing downward indicates a falling tide, and a blue arrow pointing upward indicates a rising tide. When you move the cursor over the tide station indicator, the height of the tide at the station appears above the station indicator. Current direction indicators appear as arrows on the chart. The direction of each arrow indicates the direction of the current at a specific location on the chart. The color of the current arrow indicates the range of speed for the current at that location. When you move the cursor over the current direction indicator, the specific current speed at the location appears above the direction indicator. Color Current Speed Range Yellow 0 to 1 knot Orange 1 to 2 knots Red 2 or more knots Showing and Configuring Tides and Currents NOTE: This feature is available with premium charts, in some areas. You can show static or animated tide and current station indicators on the Navigation chart or Fishing chart. 1 From the Navigation or Fishing chart, select Menu > Chart Menu > Chart Setup > Tides & Currents. 2 Select an option: • To show current station indicators and tide station indicators on the chart, select On. • To show animated tide station indicators and animated current direction indicators on the chart, select Animated. Charts and 3D Chart Views NOTE: This feature is available with premium charts, in some areas. You can overlay high-resolution satellite images on the land or on both land and sea portions of the Navigation chart. NOTE: When enabled, high-resolution satellite images are present only at lower zoom levels. If you cannot see highresolution images in your optional chart region, you can select to zoom in. You also can set the detail level higher by changing the map zoom detail. 1 From the Navigation chart, select Menu > Chart Menu > Chart Setup > Satellite Photos. 2 Select an option: • Select Land Only to show standard chart information on the water, with photos overlaying the land. • Select Photo Map to show photos on both the water and the land at a specified opacity. Use the slider bar to adjust the photo opacity. The higher you set the percentage, the more the satellite photos cover both land and water. Viewing Aerial Photos of Landmarks Target is lost. A green X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost target symbol disappears from the chart or the 3D chart view. Dangerous target in range. The target flashes while an alarm sounds and a message banner appears. After the alarm has been acknowledged, a solid red triangle with a red line attached to it indicates the location and the heading of the target. If the safe-zone collision alarm has been set to Off, the target flashes, but the audible alarm does not sound and the alarm banner does not appear. If the AIS transmission from the vessel is lost, a message banner appears. Dangerous target is lost. A red X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost dangerous target symbol disappears from the chart or the 3D chart view. The location of this symbol indicates the closest point of approach to a dangerous target, and the numbers near the symbol indicate the time to the closest point of approach to that target. NOTE: Vessels being tracked with the Blue Force Tracking feature are indicated with a blue-green color regardless of their status. Heading and Projected Course of Activated AIS Targets Automatic Identification System EN Before you can view aerial photos on the Navigation chart, you must turn on the Satellite Photos setting in the chart setup. NOTE: This feature is available with premium charts, in some areas. You can use aerial photographs of landmarks, marinas, and harbors to help orient yourself to your surroundings or to acquaint yourself with a marina or a harbor prior to arrival. 1 From the Navigation chart, select a camera icon: • To view an overhead photo, select • To view a perspective photo, select . The photo was taken from the location of the camera, pointed in the direction of the cone. 2 Select Aerial Photo. Symbol Description TI AL Showing Satellite Imagery on the Navigation Chart FI The Automatic Identification System (AIS) enables you to identify and track other vessels, and alerts you to area traffic. When connected to an external AIS device, the chartplotter can show some AIS information about other vessels that are within range, that are equipped with a transponder, and that are actively transmitting AIS information. The information reported for each vessel includes the Maritime Mobile Service Identity (MMSI), location, GPS speed, GPS heading, time that has elapsed since the last position of the vessel was reported, nearest approach, and time to the nearest approach. Some chartplotter models also support Blue Force Tracking. Vessels being tracked with Blue Force Tracking are indicated on the chartplotter with a blue-green color. AIS Targeting Symbols Symbol Description AIS vessel. The vessel is reporting AIS information. The direction in which the triangle is pointing indicates the direction in which the AIS vessel is moving. Target is selected. Target is activated. The target appears larger on the chart. A green line attached to the target indicates the heading of the target. The MMSI, speed, and direction of the vessel appear beneath the target, if the details setting has been set to Show. If the AIS transmission from the vessel is lost, a message banner appears. Charts and 3D Chart Views When heading and course over ground information are provided by an activated AIS target, the heading of the target appears on a chart as a solid line attached to the AIS target symbol. A heading line does not appear on a 3D chart view. The projected course of an activated AIS target appears as a dashed line on a chart or a 3D chart view. The length of the projected course line is based on the value of the projected heading setting. If an activated AIS target is not transmitting speed information, or if the vessel is not moving, a projected course line does not appear. Changes in the speed, course over ground, or rate of turn information transmitted by the vessel can impact the calculation of the projected course line. When course over ground, heading, and rate of turn information are provided by an activated AIS target, the projected course of the target is calculated based on the course over ground and the rate of turn information. The direction in which the target is turning, which is also based on the rate of turn information, is indicated by the direction of the barb at the end of the heading line. The length of the barb does not change. When course over ground and heading information are provided by an activated AIS target, but rate of turn information is not provided, the projected course of the target is calculated based on the course over ground information. Showing AIS and MARPA Vessels on a Chart or on a 3D Chart View Before you can show AIS vessels on a chart, you must have an external AIS device and active transponder signals from other vessels. Mini Automatic Radar Plotting Aid (MARPA) functionality works with radar. You can configure how other vessels appear on a chart or on a 3D chart view. The display range and MARPA settings configured for one chart or one 3D chart view are applied only to that chart or to that 3D chart view. The details, projected heading, and trails settings configured for one chart or one 3D chart view are applied to all charts and to all 3D chart views. > Other Vessels > Display Setup. 2 Select an option: • To indicate the distance from your location in which AIS vessels appear, select Display Range, and select a distance. • To show MARPA-tagged vessels, select MARPA > Show. • To show details about AIS-activated and MARPA-tagged vessels, select Details > Show. • To set the projected heading time for AIS-activated and MARPA-tagged vessels, select Proj. Heading, and enter the time. • To show the tracks of AIS vessels, select the length of the track that appears using a trail, select Trails, and select the length. Activating a Target for an AIS Vessel 1 From a chart or a 3D chart view, select an AIS vessel. 2 Select AIS Vessel > Activate Target. Viewing a List of AIS and MARPA Threats 1 From a chart or a 3D chart view, select Menu > Other Vessels > List > Show. Setting the Safe-Zone Collision Alarm 2 Select the type of threats to include in the list. FI Before you can set a collision alarm, you must have a compatible chartplotter connected to an AIS device or radar. The safe-zone collision alarm is used only with AIS and MARPA. MARPA functionality works with radar. The safe zone is used for collision avoidance and can be customized. 1 Select Settings > Alarms > AIS > Collision Alarm > On. A message banner appears and an alarm sounds when a MARPA-tagged object or an AIS-activated vessel enters the safe-zone area around your boat. The object is also labeled as dangerous on the screen. When the alarm is off, the message banner and audible alarm are disabled, but the object is still labeled as dangerous on the screen. 2 Select Range. 3 Select a distance for the safe-zone radius around your vessel. 4 Select Time To. 5 Select a time at which the alarm will sound if a target is determined to intersect the safe zone. For example, to be notified of a pending intersection 10 minutes before it will likely occur, set Time To to 10, and the alarm will sound 10 minutes before the vessel intersects the safe zone. AIS Distress Signals Self-contained AIS distress signal devices transmit emergency position reports when activated. The chartplotter can receive signals from Search and Rescue Transmitters (SART), Emergency Position Indicating Radio Beacons (EPIRB), and other man overboard signals. Distress signal transmissions are different than standard AIS transmissions, so they appear differently on the chartplotter. Instead of tracking a distress AIS Distress Signal Device Targeting Symbols Symbol Description AIS distress signal device transmission. Select to see more information about the transmission and begin navigation. Transmission lost. Transmission test. Appears when a vessel initiates a test of their distress signal device, and does not represent a true emergency. Enabling AIS Transmission Test Alerts To avoid a large number of test alerts and symbols in crowded areas such as marinas, you can select to receive or ignore AIS test messages. To test an AIS emergency device, you must enable the chartplotter to receive test alerts. 1 Select Settings > Alarms > AIS. 2 Select an option: • To receive or ignore Emergency Position Indicating Radio Beacon (EPRIB) test signals, select AIS-EPIRB Test. • To receive or ignore Man Overboard (MOB) test signals, select AIS-MOB Test. • To receive or ignore Search and Rescue Transponder (SART) test signals, select AIS-SART Test. EN Deactivating a Target for an AIS Vessel Navigating to a Distress Signal Transmission When you receive a distress signal transmission, a distress signal alarm appears. Select Review > Go To to begin navigation to the transmission. Transmission test lost. Viewing Information about a Targeted AIS Vessel You can view the AIS signal status, MMSI, GPS speed, GPS heading, and other information that is reported about a targeted AIS vessel. 1 From a chart or a 3D chart view, select an AIS vessel. 2 Select AIS Vessel. 1 From a chart or a 3D chart view, select an AIS vessel. 2 Select AIS Vessel > Deactivate. signal transmission for collision avoidance, you track a distress signal transmission to locate and assist a vessel or person. TI AL 1 From a chart or a 3D chart view, select Menu > Chart Menu Turning Off AIS Reception AIS signal reception is turned on by default. Select Settings > Other Vessels > AIS > Off. All AIS functionality on all charts and 3D chart views is disabled. This includes AIS vessel targeting and tracking, collision alarms that result from AIS vessel targeting and tracking, and the display of information about AIS vessels. Chart and 3D Chart View Settings NOTE: Not all settings apply to all charts and 3D chart views. Some options require premium maps or connected accessories, such as radar. These settings apply to the charts and 3D chart views, except the radar overlay and Fish Eye 3D (Fish Eye 3D Settings). From a chart or a 3D chart view, select Menu > Chart Menu. Waypoints and Tracks: See Waypoints and Tracks Settings on the Charts and Chart Views. Other Vessels: See Other Vessels Settings on the Charts and Chart Views. Surface Radar: Shows surface radar details on the Perspective 3D or Mariner's Eye 3D chart views. Weather Radar: Shows weather radar imaging on the Perspective 3D or Mariner's Eye 3D chart views. Navaids: Shows navigational aids on the Fishing chart. Laylines: Adjusts the laylines, when in sailing mode (Laylines Settings). Chart Setup: See Navigation and Fishing Chart Setup. Chart Appearance: See Chart Appearance Settings. This might appear in the Chart Setup menu. Charts and 3D Chart Views World Map: Uses either a basic world map or a shaded relief map on the chart. These differences are visible only when zoomed out too far to see the detailed charts. Spot Depths: Turns on spot soundings and sets a dangerous depth. Spot depths that are equal to or more shallow than the dangerous depth are indicated by red text. Safety Shading: Sets the shades from the shoreline to the specified depth. Depth Range Shading: Specifies an upper and lower depth to shade between. Symbols: Shows and configures the appearance of various symbols on the chart, such as the vessel icon, navaid symbols, land POIs, and light sectors. Inset Map: Shows a map zoomed in on the vessel's location in the corner of the main map. Style: Sets how the chart appears over 3D terrain. Hazard Colors: Shows shallow water and land with a color scale. Blue indicates deep water, yellow is shallow water, and red is very shallow water. Safe Depth: Sets the appearance of a safe depth for Mariner’s Eye 3D. NOTE: This setting affects only the appearance of hazard colors in Mariner’s Eye 3D. It does not affect the safe water depth Auto Guidance setting or the sonar shallow water alarm setting. Range Rings: Shows and configures the appearance of range rings, which help you to visualize distances in some chart views. Lane Width: Specifies the width of the navigation lane, which is the magenta line in some chart views that indicates the course to your destination. EN NOTE: Not all settings apply to all charts and 3D chart views. Some settings require external accessories or applicable premium charts. From the Navigation chart or Fishing chart, select Menu > Chart Menu > Chart Setup. Satellite Photos: Shows high-resolution satellite images on the land or on both land and sea portions of the Navigation chart, when certain premium maps are used (Showing Satellite Imagery on the Navigation Chart). Water Overlay: Enables relief shading, which shows the gradient of the bottom with shading, or sonar imagery, which helps identify the density of the of the bottom. This feature is available only with some premium maps. Tides & Currents: Shows current station indicators and tide station indicators on the chart (Showing and Configuring Tides and Currents) and enables the tides and current slider, which sets the time for which tides and currents are reported on the map. Roses: Shows a compass rose around your boat, indicating compass direction oriented to the heading of the boat. A true wind direction or apparent wind direction indicator appears if the chartplotter is connected to a compatible marine wind sensor. When in sailing mode, true and apparent wind are shown on the wind rose. Lake Level: Sets the present water level of the lake. This feature is available only with some premium maps. Inset Map: Shows a small map centered on your present location. Weather: Sets which weather items are shown on the chart, when the chartplotter is connected to a compatible weather receiver with an active subscription. Requires a compatible, connected antenna and an active subscription. Chart Appearance: See Chart Appearance Settings. TI AL Navigation and Fishing Chart Setup Waypoints and Tracks Settings on the Charts and Chart Views FI From a chart or a 3D chart view, select Menu > Chart Menu > Waypoints and Tracks. Tracks: Shows tracks on the chart or 3D chart view. Waypoints: Shows the list of waypoints (Viewing a List of all Waypoints). Create Waypoint: Creates a new waypoint. Waypoint Display: Sets how to display waypoints on the chart. Active Tracks: Shows the active track options menu. Saved Tracks: Shows the list of saved tracks (Viewing a List of Saved Tracks). Tracks Display: Sets which tracks to display on the chart based on track color. Chart Appearance Settings You can adjust the appearance of the different chart views. Each setting is specific for the type of chart view that you are in. NOTE: Not all settings apply to all charts and 3D chart views and chartplotter models. Some options require premium maps or connected accessories, such as radar. From a chart or 3D chart view, select Menu > Chart Menu > Chart Setup > Chart Appearance. Orientation: Sets the perspective of the map. Detail: Adjusts the amount of detail shown on the map, at different zoom levels. Heading Line: Shows and adjusts the heading line, which is a line drawn on the map from the bow of the boat in the direction of travel, and sets the data source for the heading line. Charts and 3D Chart Views Other Vessels Settings on the Charts and Chart Views NOTE: These options require connected accessories, such as an AIS receiver or VHF radio. From a chart or a 3D chart view, select Menu > Chart Menu > Other Vessels. List: Shows a list of AIS and MARPA vessels. DSC: Shows the DSC list and sets the DSC trails on the chart. Collision Alarm: Sets the safe-zone collision alarm (Setting the Safe-Zone Collision Alarm). Display Setup: See Showing AIS and MARPA Vessels on a Chart or on a 3D Chart View. Laylines Settings When in sailing mode (Setting the Vessel Type), you can display laylines on the navigation chart. Laylines can be very helpful when racing. From the navigation chart, select Menu > Chart Menu > Sailing > Laylines. Display: Sets how the laylines and vessel are shown on the chart, and sets the length of the laylines. Sailing Ang.: Allows you to select how the device calculates laylines. The Actual option calculates the laylines using the measured wind angle from the wind sensor. The Manual option calculates the laylines using manually entered windward and leeward angles. Tide Correction: Corrects the laylines based on the tide. Fish Eye 3D Settings NOTE: This feature is available with premium charts, in some areas. From the Fish Eye 3D chart view, select Menu > Chart Menu. View: Sets the perspective of the 3D chart view. Tracks: Shows tracks. Navigation with a Chartplotter CAUTION If your vessel has an autopilot system, a dedicated autopilot control display must be installed at each steering helm in order to disable the autopilot system. The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. Answer How do I make the device guide me to a location while avoiding charted obstacles? Build a multi-leg route and navigate it using Route To. See Creating and Navigating a Route From Your Present Location. How do I make the device steer my automatic pilot? Navigate using Route To. See Creating and Navigating a Route From Your Present Location. Can the device create a path for me? If you have premium maps that support Auto Guidance and are in an area covered by Auto Guidance, navigate using Auto Guidance. See Setting and Following an Auto Guidance Path. How do I change the Auto See Auto Guidance Line Guidance settings for my boat? Configurations. Destinations You can select destinations using various charts and 3D chart views or using the lists. Searching for a Destination by Name You can search for saved waypoints, saved routes, saved tracks, and marine services destinations by name. 1 Select Info > Services > Search by Name. 2 Enter at least a portion of the name of your destination. 3 If necessary, select Done. The 50 nearest destinations that contain your search criteria appear. 4 Select the destination. FI EN NOTE: Auto Guidance is available with premium charts, in some areas. NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are available with premium charts, in some areas. NOTE: The offshore Fishing chart is available with premium charts, in some areas. To navigate, you must choose a destination, set a course or create a route, and follow the course or route. You can follow the course or the route on the Navigation chart, Fishing chart, Perspective 3D chart view, or Mariner’s Eye 3D chart view. You can set and follow a course to a destination using one of three methods: Go To, Route To, or Auto Guidance. Go To: Takes you directly to the destination. This is the standard option for navigating to a destination. The chartplotter creates a straight-line course or navigation line to the destination. The path may run over land and other obstacles. Route To: Creates a route from your location to a destination, allowing you to add turns along the way. This option provides a straight-line course to the destination, but allows you to add turns into the route to avoid land and other obstacles. Auto Guidance: Creates a path to a destination using Auto Guidance. This option is available only when using a compatible premium chart in a compatible chartplotter. It provides a turn-by-turn navigation line to the destination, avoiding land and other obstacles. The navigation line is based on the chart data and the safe depth, safe height, and shoreline distance user-defined chartplotter settings. Using these settings and chart data, the chartplotter creates a navigation line that avoids all areas that cannot be navigated between the present location and the destination. When you are using a compatible Garmin autopilot connected to the chartplotter using NMEA 2000 , the autopilot follows the Auto Guidance route. Question TI AL Sonar Cone: Shows a cone that indicates the area covered by the transducer. Fish Symbols: Shows suspended targets. ® Basic Navigation Questions Question Answer How do I make the chartplotter Navigate using Go To. See Setting point me in the direction in and Following a Direct Course Using which I want to go (bearing)? Go To. How do I make the device guide me along a straight line (minimizing cross track) to a location using the shortest distance from the present location? Build a single-leg route and navigate it using Route To. See Creating and Navigating a Route From Your Present Location. Selecting a Destination Using the Navigation Chart From the Navigation chart, select a destination. Searching for a Marine Services Destination NOTE: This feature is available with premium charts, in some areas. The chartplotter contains information for thousands of destinations offering marine services. 1 Select Info > Services. 2 Select Offshore Services or Inland Services. 3 If necessary, select the marine service category. The chartplotter shows a list of the nearest locations and the distance and bearing to each. 4 Select a destination. You can select Next Page or Previous Page to view additional information or to show the location on a chart. Searching for a Volvo Penta Dealer ® Select Info > Services > Volvo Penta Dealers. Waypoints Waypoints are locations you record and store in the device. Marking Your Present Location as a Waypoint From any screen, select Mark. Creating a Waypoint at a Different Location 1 Select Info > User Data > Waypoints > Create Waypoint. 2 Select an option: • To create the waypoint by entering position coordinates, select Enter Coordinates, and enter the coordinates. • To create the waypoint using a chart, select Use Chart, select the location, and select Select. Navigation with a Chartplotter Marking an SOS Location You can mark an SOS location. When a Garmin VHF radio is connected using NMEA 2000, you can select different SOS types, such as Man Overboard and Piracy. 1 From the Home screen, select SOS. 2 Select the SOS type. 3 If necessary, select OK to navigate to the man overboard location. If you selected OK, the chartplotter sets a direct course back to the location. If you selected another type of SOS, the call details are sent to the VHF radio. You must send the call using the radio. Viewing a List of all Waypoints Setting and Following a Direct Course Using Go To FI • To move the waypoint while using the chart, select Use Chart, select a new location on the chart, and select Move Waypoint. • To move the waypoint using coordinates, select Enter Coordinates, and enter the new coordinates. Browsing for and Navigating to a Saved Waypoint CAUTION The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. NOTE: Auto Guidance is available with premium charts, in some areas. Before you can navigate to a waypoint, you must create a waypoint. 1 Select Info > User Data > Waypoints. 2 Select a waypoint. 3 Select Navigate To. 4 Select an option: • To navigate directly to the location, select Go To. • To create a route to the location, including turns, select Route To. • To use Auto Guidance, select Auto Guidance. 5 Review the course indicated by the magenta line. CAUTION When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. You can set and follow a direct course from your current location to a selected destination. 1 Select a destination (Destinations). 2 Select Navigate To > Go To. A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your current location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course. 3 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. 4 If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line (direct course). EN To add a name, select Name, and enter a name. To change the symbol, select Symbol. To change the depth, select Depth. To change the water temperature, select Water Temp.. To change the comment, select Comment. Navigation with a Chartplotter Deleting All Waypoints TI AL Editing a Saved Waypoint 1 Select Info > User Data > Waypoints. 2 Select a waypoint. 3 Select Review > Edit. 4 Select an option: Moving a Saved Waypoint 1 Select Info > User Data > Waypoints. 2 Select a waypoint. 3 Select Review > Move. 4 Indicate a new location for the waypoint: Deleting a Waypoint or an MOB 1 Select Info > User Data > Waypoints. 2 Select a waypoint or an MOB. 3 Select Review > Delete. Select Info > User Data > Clear User Data > Waypoints > All. Select Info > User Data > Waypoints. • • • • • NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height. 6 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. Routes Creating and Navigating a Route From Your Present Location You can create and immediately navigate a route on the Navigation chart or the Fishing chart. This procedure does not save the route or the waypoint data. NOTE: The offshore Fishing chart is available with premium charts, in some areas. 1 From the Navigation chart or Fishing chart, select a destination. 2 Select Navigate To > Route To. 3 Select the location of the last turn before the destination. 4 Select Add Turn. 5 If necessary, repeat step 3 and 4 to add additional turns, working backward from the destination to the present location of your vessel. The last turn you add should be the first turn you make, starting from your present location. It should be the turn closest to your vessel. 6 If necessary, select Menu. 7 Select Navigate Route. 8 Review the course indicated by the magenta line. 9 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. 6 Viewing a List of Routes Select Info > User Data > Routes & Auto Guidance Paths. Editing a Saved Route Browsing for and Navigating a Saved Route FI Before you can browse a list of routes and navigate to one of them, you must create and save at least one route. 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Navigate To. 4 Select an option: • To navigate the route from the starting point used when the route was created, select Forward. • To navigate the route from the destination point used when the route was created, select Backward. A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your present location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course. 5 Review the course indicated by the magenta line. 6 Follow the magenta line along each leg in the route, steering to avoid land, shallow water, and other obstacles. 7 If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line (direct course). Browsing for and Navigating Parallel to a Saved Route Before you can browse a list of routes and navigate to one of them, you must create and save at least one route. 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Navigate To. 4 Select Offset to navigate parallel to the route, offset from it by a specific distance. 5 Indicate how to navigate the route: 10 Deleting a Saved Route 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Review > Delete. EN You can change the name of a route or change the turns the route contains. 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Review > Edit Route. 4 Select an option: • To change the name, select Name, and enter the name. • To select a waypoint from the turn list, select Edit Turns > Use Turn List, and select a waypoint from the list. • To select a turn using the chart, select Edit Turns > Use Chart, and select a location on the chart. • To navigate the route from the starting point used when the route was created, to the left of the original route, select Forward – Port. • To navigate the route from the starting point used when the route was created, to the right of the original route, select Forward – Starboard. • To navigate the route from the destination point used when the route was created, to the left of the original route, select Backward – Port. • To navigate the route from the destination point used when the route was created, to the right of the original route, select Backward – Starboard. If necessary, select Done. A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your present location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course. Review the course indicated by the magenta line. Follow the magenta line along each leg in the route, steering to avoid land, shallow water, and other obstacles. If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line (direct course). TI AL Creating and Saving a Route This procedure saves the route and all the waypoints in it. The starting point can be your present location or another location. 1 Select Info > User Data > Routes & Auto Guidance Paths > New > Use Chart. 2 Select the starting location of the route. 3 Select Add Turn. 4 Select the location of the next turn on the chart. 5 Select Add Turn. The chartplotter marks the location of the turn with a waypoint. 6 If necessary, repeat steps 4 and 5 to add more turns. 7 Select the final destination. Deleting All Saved Routes Select Info > User Data > Clear User Data > Routes & Auto Guidance Paths. Auto Guidance CAUTION The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. NOTE: Auto Guidance is available with premium charts, in some areas. You can use Auto Guidance to plot the best path to your destination. Auto Guidance uses your chartplotter to scan chart data, such as water depth and known obstacles, to calculate a suggested path. You can adjust the path during navigation. Setting and Following an Auto Guidance Path 1 Select a destination (Destinations). 2 Select Navigate To > Auto Guidance. 3 Review the path, indicated by the magenta line. 4 Select Start Navigation. 5 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height. Creating and Saving an Auto Guidance Path 1 Select Info > User Data > Routes & Auto Guidance Paths > New > Auto Guidance. 2 Select a starting point, and select Next. Navigation with a Chartplotter • To view a hazard and adjust the hazard path, select Hazard Review. • To adjust the path, select Adjust Path, and follow the onscreen instructions. • To delete the path, select Cancel Auto Guidance. • To save the path, select Done. Adjusting a Saved Auto Guidance Path 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a path, and select Review > Edit > Adjust Path. TIP: When navigating an Auto Guidance path, select the path on the navigation chart, and select Adjust Path. Select a location on the path. Drag the point to a new location. If necessary, select a point, and select Remove. Select Done. Canceling an Auto Guidance Calculation in Progress From the Navigation chart, select Menu > Cancel. TIP: You can select Back to quickly cancel the calculation. Setting a Timed Arrival Adjusting the Distance from Shore The Shoreline Distance setting indicates how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for the Shoreline Distance setting are relative, not absolute. To ensure the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway. 1 Dock your vessel or drop the anchor. 2 Select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Normal. Select a destination that you have navigated to previously. 4 Select Navigate To > Auto Guidance. 5 Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. 6 Select an option: • If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. • If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Far. • If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Near. 7 If you selected Near or Far in step 6, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 8 Select an option: • If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. • If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Farthest. • If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Nearest. 9 If you selected Nearest or Farthest in step 8, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 10 Repeat steps 3 through 9 at least once more, using a different destination each time, until you are familiar with the functionality of the Shoreline Distance setting. Auto Guidance Line Configurations EN You can use the Timed Arrival feature on a route or an Auto Guidance path to get feedback regarding when you should arrive at a selected point. This allows you to time your arrival at a location, such as a bridge opening or a race starting line. 1 From the Navigation chart, select Menu. 2 If necessary, select Navigation Options. 3 Select Timed Arrival. TIP: You can quickly open the Timed Arrival menu by selecting a point on the Auto Guidance path. Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway (Adjusting the Distance from Shore). TI AL 3 Select a destination, and select Next. 4 Select an option: FI CAUTION The Safe Depth and Safe Height settings influence how the chartplotter calculates an Auto Guidance line. If an area has an unknown water depth or an unknown obstacle height, the Auto Guidance line is not calculated in that area. If an area at the beginning or the end of an Auto Guidance line is shallower than the safe water depth or lower than the safe obstacle height, the Auto Guidance line is not calculated in that area. On the chart, the course through those areas appears as a gray line. When your boat enters one of those areas, a warning message appears. NOTE: Auto Guidance is available with premium charts, in some areas. You can set the parameters the chartplotter uses when calculating an Auto Guidance line. Safe Depth: Sets the minimum depth (chart depth datum) the chartplotter uses when calculating an Auto Guidance line. NOTE: The minimum safe depth for the premium charts is 3 feet. If you enter a Safe Depth value of less than 3 feet, the charts only use depths of 3 feet for Auto Guidance route calculations. Safe Height: Sets the minimum height (chart height datum) of a bridge that your boat can safely travel under. Shoreline Distance: Sets how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for this setting are relative, not absolute. To ensure that the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Navigation with a Chartplotter 11 Tracks 2 Select an option: Showing Tracks From a chart or a 3D chart view, select Menu > Chart Menu > Waypoints and Tracks > Tracks > On. A trailing line on the chart indicates your track. Setting the Color of the Active Track 1 Select Info > User Data > Tracks > Active Track Options > Track Color. 2 Select a track color. Saving the Active Track The track currently being recorded is called the active track. 1 Select Info > User Data > Tracks > Save Active Track. 2 Select an option: • Select the time the active track began. • Select Entire Log. 3 Select Save. Viewing a List of Saved Tracks Editing a Saved Track 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Edit Track. 4 Select an option: • Select Name, and enter the new name. • Select Track Color, and select a color. FI Saving a Track as a Route 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Select > Edit Track > Save Route. Browsing for and Navigating a Recorded Track Before you can browse a list of tracks and navigate to them, you must record and save at least one track (Tracks). 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Follow Track. 4 Select an option: • To navigate the track from the starting point used when the track was created, select Forward. • To navigate the track from the destination point used when the track was created, select Backward. 5 Review the course indicated by the colored line. 6 Follow the line along each leg in the route, steering to avoid land, shallow water, and other obstacles. Deleting a Saved Track 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Select > Delete. Deleting All Saved Tracks Select Info > User Data > Clear User Data > Saved Tracks. Retracing the Active Track The track currently being recorded is called the active track. 1 Select Info > User Data > Tracks > Follow Active Track. 12 Clearing the Active Track Select Info > User Data > Tracks > Clear Active Track. The track memory is cleared, and the active track continues to be recorded. Managing the Track Log Memory During Recording 1 Select Info > User Data > Tracks > Active Track Options. 2 Select Record Mode. 3 Select an option: • To record a track log until the track memory is full, select Fill. • To continuously record a track log, replacing the oldest track data with new data, select Wrap. Configuring the Recording Interval of the Track Log You can indicate the frequency at which the track plot is recorded. Recording more frequent plots is more accurate but fills the track log faster. The resolution interval is recommended for the most efficient use of memory. 1 Select Info > User Data > Tracks > Active Track Options > Interval > Interval. 2 Select an option: • To record the track based on a distance between points, select Distance > Change, and enter the distance. • To record the track based on a time interval, select Time > Change, and enter the time interval. • To record the track plot based on a variance from your course, select Resolution > Change, and enter the maximum error allowed from the true course before recording a track point. EN Select Info > User Data > Tracks > Saved Tracks. • Select the time the active track began. • Select Entire Log. 3 Review the course indicated by the colored line. 4 Follow the colored line, steering to avoid land, shallow water, and other obstacles. TI AL A track is a recording of the path of your boat. The track currently being recorded is called the active track, and it can be saved. You can show tracks in each chart or 3D chart view. Stopping Navigation While navigating, from the Navigation or Fishing chart, select an option: • Select Menu > Stop Navigation. • When navigating with Auto Guidance, select Menu > Navigation Options > Stop Navigation. Synchronizing User Data Across the Garmin Marine Network NOTICE Before you synchronize the user data across the network, you should backup your user data to prevent possible data loss. See Backing Up Data to a Computer. You can share waypoints, tracks, and routes with all compatible devices connected to the Garmin Marine Network (Ethernet) automatically. NOTE: This feature is not available on all models. Select Settings > Preferences > User Data Sharing > On. If a change is made to a waypoint, track, or route on one chartplotter, that data is synchronized automatically across all chartplotters on the Ethernet network. Deleting All Saved Waypoints, Routes, and Tracks Select Info > User Data > Clear User Data > All > OK. Navigation with a Chartplotter Sailing Features 4 Select Back. 5 Start the racing timer (Starting the Race Timer). You can select your boat type to configure the chartplotter settings and to use features customized for your boat type. 1 Select Settings > My Vessel > Vessel Type. 2 Select Powerboat or Sailboat. Sail Racing You can use the device to increase the likelihood that your boat will cross the start line of a race exactly when the race begins. When you synchronize the race timer with the official race countdown timer, you are alerted at one-minute intervals as the race start approaches. When you combine the race timer with the virtual start line, the device measures your speed, bearing, and remaining time on the countdown timer. The device uses this data to indicate whether your boat will cross the start line before, after, or at the correct time to start the race. Starting Line Guidance The race timer is added to the Sail Racing combination screen by default. 1 From the Sail Racing combination screen, select Start. NOTE: You can also access this from the Sailing SmartMode screen and the navigation chart. 2 When necessary, select Sync to synchronize with the official race timer. Stopping the Race Timer From the Sail Racing combination screen, select Stop. Setting the Distance between the Bow and the GPS Antenna You can enter the distance between the bow of your boat and the location of your GPS antenna. This helps ensure the bow of your boat crosses the starting line at the precise start time. 1 From a navigation chart, select Sailing > Start Line > GPS Bow Offset. 2 Enter the distance. 3 Select Done. Laylines Settings When in sailing mode (Setting the Vessel Type), you can display laylines on the navigation chart. Laylines can be very helpful when racing. From the navigation chart, select Menu > Chart Menu > Sailing > Laylines. Display: Sets how the laylines and vessel are shown on the chart, and sets the length of the laylines. Sailing Ang.: Allows you to select how the device calculates laylines. The Actual option calculates the laylines using the measured wind angle from the wind sensor. The Manual option calculates the laylines using manually entered windward and leeward angles. Tide Correction: Corrects the laylines based on the tide. Setting the Starting Line FI EN Sailing start line guidance is a visual representation of the information you need to cross the start line at the optimal time and speed. After you set the starboard and port start line pins, and the target speed and time, and after you start the race timer, a predictor line appears. The predictor line extends from your current location toward the start line and the laylines that extend from each pin. The end point and color of the predictor line indicate where the boat will be when the timer expires, based on your current boat speed. When the end point is before the start line, the line is white. This indicates the boat must increase speed to reach the start line on time. When the end point is past the start line, the line is red. This indicates the boat must reduce speed to avoid a penalty for reaching the start line before the timer expires. When the end point is on the start line, the line is white. This indicates the boat is moving at an optimal speed to reach the start line when the timer expires. By default, the start line guidance window and the race timer window appear in the Sail Racing combination screen. Starting the Race Timer TI AL Setting the Vessel Type The start line guidance window is added to the Sail Racing combination screen by default. 1 From the Sail Racing combination screen, select Menu > Start Line Guidance > Start Line. 2 Select an option: • To mark the port and starboard starting line marks as you sail past them, select Ping Marks. • To mark the port and starboard starting line marks by entering their coordinates, select Enter Coordinates. • To switch the position of the port and starboard marks after you have set them, select Swap Port & Starbd. Marks. Setting the Keel Offset You can enter a keel offset to compensate the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location. Enter a positive number to offset for a keel. You can enter a negative number to compensate for a large vessel that may draw several feet of water. 1 Complete an action, based on the location of the transducer: • If the transducer is installed at the water line À, measure the distance from the transducer location to the keel of the boat. Enter this value in steps 3 and 4 as a positive number. • If the transducer is installed at the bottom of the keel Á, measure the distance from the transducer to the water line. Enter this value in steps 3 and 4 as a negative number. Using the Starting Line Guidance You can use the starting line guidance feature to help get you cross the start line, at the optimal speed during a sailing race. 1 Mark the starting line (Setting the Starting Line). 2 From the Sail Racing combination screen, select Menu > Start Line Guidance > Target Speed, and select your target speed when crossing the starting line. 3 Select Target Time, and select the target time to cross the starting line. Sailing Features 13 Tacking and Gybing from Heading Hold 1 Engage heading hold (Engaging the Autopilot). 2 Select Menu > Autopilot Menu > Tack Gybe. 3 Select a direction. The autopilot steers your boat through a tack or gybe. Setting a Tack and Gybe Delay The tack and gybe delay allows you to delay steering a tack and gybe after you initiate the maneuver. 1 From the autopilot screen, select Menu > Autopilot Menu > Autopilot Setup > Sailing Setup > Tack Delay. 2 Select the length of the delay. 3 If necessary, select Done. 2 Select Settings > My Vessel > Keel Offset. 3 Select or based on the location of the transducer. 4 Enter the distance measured in step 1. Sailboat Autopilot Operation In addition to heading hold, you can use the autopilot to maintain a wind hold. You can also use the autopilot to control the rudder while tacking and gybing. Wind Hold You can set the autopilot to maintain a specific bearing relative to the current wind angle. Your device must be connected to a NMEA 2000 or NMEA 0183 compatible wind sensor to perform a wind hold or a wind-based tack or gybe. ® FI Setting the Wind Hold Type Before you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot. For advanced autopilot configuration, see the installation instructions included with your autopilot. 1 From the autopilot screen, select Menu > Autopilot Menu > Autopilot Setup > Wind Hold Type. 2 Select Apparent or True. Engaging Wind Hold Before you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot. When the autopilot is in standby mode, select Wind Hold. Engaging Wind Hold from Heading Hold Before you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot. With heading hold engaged, select Menu > Wind Hold. Adjusting the Wind Hold Angle with the Autopilot You can adjust the wind hold angle on the autopilot when wind hold is engaged. • To adjust the wind hold angle in increments of 1°, select or • To adjust the wind hold angle in increments of 10°, hold or You can set the autopilot to perform a tack or gybe while heading hold or wind hold is engaged. 14 Enabling the Gybe Inhibitor NOTE: The gybe inhibitor does not prevent you from manually performing a gybe using the helm or step steering. The gybe inhibitor prevents the autopilot from performing a gybe. 1 Select Menu > Autopilot Menu > Autopilot Setup > Sailing Setup > Gybe Inhibitor. 2 Select Enabled. EN CAUTION When engaged, the autopilot controls only the rudder. You and your crew remain responsible for the sails while the autopilot is engaged. Tack and Gybe TI AL Tacking and Gybing from Wind Hold Before you can engage wind hold, you must have a wind sensor installed. 1 Engage wind hold (Engaging Wind Hold). 2 Select Menu > Tack Gybe. 3 Select Tack or Gybe. The autopilot steers your boat through a tack or gybe, and information about the progress of the tack or gybe appears on the screen. Sonar When properly connected to a compatible transducer, your chartplotter can be used as a fishfinder. Different sonar views can help you view the fish in the area. The adjustments you can make to each sonar view vary depending on the view you are in and the chartplotter model and transducer you have connected. Sonar Views The sonar views available vary depending on the type of transducer and optional sounder module connected to the chartplotter. For example, you can view the Split Frequency view only if you have a dual-frequency transducer connected. There are four basic styles of sonar views available: a fullscreen view, a split-screen view that combines two or more views, a split-zoom view, and a split-frequency view that displays two different frequencies. You can customize the settings for each view in the screen. For example, if you are viewing the split-frequency view, you can adjust the gain for each of the frequencies separately. If you do not see an arrangement of sonar views to suit your needs, you can create a custom screen (Adding a Custom Combination Screen). Traditional Sonar View There are several full-screen views available, depending on the equipment connected. The full-screen Traditional sonar view show a large image of the sonar readings from a transducer. The range scale along the right side of the screen shows the depth of detected objects as the screen scrolls from the right to the left. Sonar À Á  Depth information Suspended targets or fish Bottom of the body of water NOTE: Not all models support DownVü sonar technology and transducers. NOTE: To receive DownVü scanning sonar, you need a compatible chartplotter or fishfinder and a compatible transducer. DownVü high-frequency sonar provides a clearer picture below the boat, providing a more detailed representation of structures the boat is passing over. Traditional transducers emit a conical beam. The DownVü scanning sonar technology emits a narrow beam, similar to the shape of the beam in a copying machine. This beam provides a clearer, picture-like image of what is beneath the boat. FI NOTE: Not all models support SideVü sonar and scanning transducers. NOTE: To receive SideVü scanning sonar, you need a compatible chartplotter and a compatible transducer. SideVü scanning sonar technology shows you a picture of what lies to the sides of the boat. You can use this as a search tool to find structures and fish. Left side of the boat Right side of the boat The transducer on your vessel Trees Old tires Logs À Á Â Ã Ä Å Æ Distance from the side of the boat SideVü/DownVü Scanning Technology Instead of a more common conical beam, the SideVü/DownVü transducer uses a flat beam to scan the water and ground to the sides of your boat. Sonar Split-Zoom Sonar View The split-zoom sonar view shows a full-view graph of sonar readings, and a magnified portion of that graph, on the same screen. Split-Frequency Sonar View In the split-frequency sonar view, one side of the screen shows a full-view graph of high frequency sonar data, and the other side of the screen shows a full-view graph of lower frequency sonar data. NOTE: The split-frequency sonar view requires the use of a dual-frequency transducer. Changing the Sonar View 1 From a combination screen or SmartMode layout with sonar, EN SideVü Sonar View TI AL DownVü Sonar View select the window to change. 2 Select Menu > Change Sonar. 3 Select a sonar view. Creating a Waypoint on the Sonar Screen 1 From a sonar view, select a location. 2 Select New Wpt. 3 If necessary, edit the waypoint information. Pausing the Sonar Display From a sonar view, select . Viewing Sonar History You can scroll the sonar display to view historical sonar data. 1 From a sonar view, select Menu > Sonar Menu > . 2 Drag the screen. Sonar Sharing This feature may not be available on all chartplotter models. You can view the sonar data from all compatible sources on the Garmin Marine Network. You can view sonar data from a compatible external sonar module, such as a GCV™ sonar module. In addition, you can view the sonar data from other chartplotters that have a built-in sonar module. Each chartplotter on the network can display sonar data from every compatible sonar module and transducer on the network, no matter where the chartplotters and transducers are mounted on your boat. For example, from a transducer with DownVü mounted at the back of the boat, you can view the sonar data using the GPSMAP 7407xsv mounted at the front of your boat. Chartplotters can display only compatible types of sonar. For example, GPSMAP 547 models can display traditional and DownVü data, but not SideVü data. When sharing sonar data, the values of some sonar settings, such as Range and Gain, are synchronized across the devices on the network. The values of other sonar settings, such as the 15 Selecting a Sonar Source This feature may not be available with all models. When you are using more than one sonar data source for a particular sonar view, you can select the source to use for that sonar view. For example, if you have two sources for DownVü, you can select the source to use from the DownVü sonar view. 1 Open the sonar view for which you will change the source. 2 Select Menu > Sonar Menu > Sonar Setup > Source. 3 Select the source for this sonar view. Renaming a Sonar Source Adjusting the Level of Detail FI You can control the level of detail and noise shown on the sonar screen either by adjusting the gain for traditional transducers, or by adjusting the brightness for DownVü and SideVü/DownVü transducers. If you want to see the highest intensity signal returns on the screen, you can lower the gain or brightness to remove lower intensity returns and noise. If you want to see all return information, you can increase the gain or brightness to see more information on the screen. This also increases noise, and can make it more difficult to recognize actual returns. 1 From a sonar view, select Menu > Sonar Menu. 2 Select Gain or Brightness. 3 Select an option: • To increase or decrease the gain or brightness manually, select Up or Down. • To allow the chartplotter to adjust the gain or brightness automatically, select an automatic option. Adjusting the Color Intensity You can adjust the intensity of colors and highlight areas of interest on the sonar screen by adjusting the color gain for traditional transducers or the contrast for DownVü and SideVü/ DownVü transducers. This setting works best after you have adjusted the level of detail shown on the screen using the gain or brightness settings. If you want to highlight smaller fish targets or create a higher intensity display of a target, you can increase the color gain or contrast setting. This causes a loss in the differentiation of the high intensity returns at the bottom. If you want to reduce the intensity of the return, you can reduce the color gain or contrast. 1 From a sonar view, select Menu > Sonar Menu. 2 Select an option: • While in the DownVü or SideVü sonar view, select Contrast. • While in another sonar view, select Sonar Setup > Advanced > Color Gain. 16 • To increase or decrease the color intensity manually, select Up or Down. • To use the default setting, select Default. Adjusting the Range of the Depth or Width Scale You can adjust the range of the depth scale traditional and DownVü sonar views and the range of the width scale for the SideVü sonar view. Allowing the device to adjust the range automatically keeps the bottom within the lower or outer third of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes. Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The bottom can appear on the screen as long as it appears within the range you have set. 1 From a sonar view, select Menu > Sonar Menu > Range. 2 Select an option: • To allow the chartplotter to adjust the range automatically, select Auto. • To increase or decrease the range manually, select Up or Down. TIP: From the sonar screen, you can select or to manually adjust the range. TIP: When viewing multiple sonar screens, you can select Select to choose the active screen. EN You can rename a sonar source to easily identify that source. For example, you use "Bow" as the name of the transducer on the bow of your boat. The source is renamed for the present view only. For example, to rename the DownVü sonar source, you must open the DownVü sonar view. 1 From the sonar view, select Menu > Sonar Menu > Sonar Setup > Source > Rename Sources. 2 Enter the name. 3 Select an option: TI AL Appearance settings, are not synchronized and should be configured on each individual device. In addition, the scroll rates of the various traditional and DownVü sonar views are synchronized to make the split views more cohesive. NOTE: Using multiple transducers simultaneously can create cross talk, which can be removed by adjusting the Interference sonar setting. Setting the Zoom Level on the Sonar Screen 1 From a sonar view, select Menu > Sonar Menu > Zoom. 2 Select an option: • To zoom in on the sonar data from the bottom depth, select Bottom Lock. • To set the depth range of the magnified area manually, select Set Zoom, select View Up or View Down to set the depth range of the magnified area, and select Zoom In or Zoom Out to increase or decrease the magnification of the magnified area. • To set the depth and zoom automatically, select Set Zoom > Auto. • To cancel the zoom, select No Zoom. Setting the Scroll Speed You can set the rate at which the sonar image moves across the screen. A higher scroll speed shows more detail, especially while moving or trolling. A lower scroll speed displays sonar information on the screen longer. Setting the scroll speed on one sonar view applies to all the sonar views. 1 From a sonar view, select Menu > Sonar Menu > Sonar Setup > Scroll Speed. 2 Select an option: • To adjust the scroll speed automatically using speed-overground or water speed data, select Auto. The Auto setting selects a scroll rate to match the boat speed, so targets in the water are drawn with the correct aspect ratio and appear less distorted. When viewing DownVü or SideVü sonar views, it is recommend to use the Auto setting. • To use a very fast scroll speed, select Ultrascroll®. The Ultrascroll option quickly scrolls new sonar data, but with a reduced image quality. For most situations, the Fast Sonar Selecting the Transducer Type Sonar Frequencies Sonar Setup NOTE: Not all options and settings apply to all models and transducers. Sonar Settings From a sonar view, select Menu > Sonar Menu > Sonar Setup. Scroll Speed: Sets the rate at which the sonar scrolls from right to left (Setting the Scroll Speed). In shallow water, you can select a slower scroll speed to extend the length of time the information is displayed on screen. In deeper water, you can select a faster scroll speed. Automatic scroll speed adjusts the scrolling speed to the speed the boat is traveling. Noise Reject: Reduces the interference and the amount of clutter shown on the sonar screen (Sonar Noise Rejection Settings). Appearance: Configures the appearance of the sonar screen (Sonar Appearance Settings). Alarms: Sets sonar alarms (Sonar Alarm Settings). Advanced: Configures various sonar display and data source settings (Advanced Sonar Settings). Installation: Configures the transducer (Transducer Installation Settings). EN NOTE: The frequencies available depend on the chartplotter, sounder modules, and transducer being used. Adjusting the frequency helps adapt the sonar for your particular goals and the present depth of the water. Higher frequencies use narrow beam widths, and are better for high-speed operation and rough sea conditions. Bottom definition and thermocline definition can be better when using a higher frequency. Lower frequencies use wider beam widths, which can let the fisherman see more targets, but could also generate more surface noise and reduce bottom signal continuity during rough sea conditions. Wider beam widths generate larger arches for fish target returns, making them ideal for locating fish. Wider beam widths also perform better in deep water, because the lower frequency has better deep water penetration. Chirp frequencies allow you to sweep each pulse through a range of frequencies, resulting in better target separation in deep water. Chirp can be used to distinctly identify targets, like individual fish in a school, and for deep water applications. Chirp generally performs better than single frequency applications. Because some fish targets may show up better using a fixed frequency, you should consider your goals and water conditions when using Chirp. Some sonar black boxes and transducers also provide the ability to customize preset frequencies for each transducer element, which enables you to change the frequency quickly using the presets as the water and your goals change. Viewing two frequencies concurrently using the split-frequency view allows you to see deeper with the lower frequency return and, at the same time, see more detail from the higher frequency return. Before you can select the transducer type, you must know what kind of transducer you have. If you are connecting a transducer that was not included with the chartplotter, you may need to set the transducer type to make the sonar function properly. If the device automatically detected your transducer, this option does not appear. 1 From a sonar view, select Menu > Sonar Setup > Installation > Transducer Type. 2 Select an option: • If you have a 200/77 kHz, dual-beam transducer, select Dual Beam (200/77 kHz). • If you have a 200/50 kHz, dual-frequency transducer, select Dual Frequency (200/50 kHz). • If you have another type of transducer, select it from the list. TI AL option provides a good balance between a quickly scrolling image and targets that are less distorted. Selecting Frequencies FI NOTE: You cannot adjust the frequency for all sonar views and transducers. You can indicate which frequencies appear on the sonar screen. 1 From a sonar view, select Menu > Sonar Menu > Frequency. 2 Select a frequency suited to your needs and water depth. For more information on frequencies, see Sonar Frequencies. Creating a Frequency Preset NOTE: Not available with all transducers. You can create a preset to save a specific sonar frequency, which allows you to change frequencies quickly. 1 From a sonar view, select Menu > Sonar Menu > Frequency. 2 Select Manage Frequencies > New Preset. 3 Enter a frequency. Turning On the A-Scope NOTE: This feature is not available in all sonar views. The a-scope is a vertical flasher along the right side of the fullscreen sonar view. This feature expands the most recently received sonar data so that it is easier to see. It can also be helpful for detecting fish that are close to the bottom. From a sonar view, select Menu > Sonar Menu > Sonar Setup > Appearance > A-Scope > On. Sonar Sonar Noise Rejection Settings From a sonar view, select Menu > Sonar Menu > Sonar Setup > Noise Reject. Interference: Adjusts the sensitivity to reduce the effects of interference from nearby sources of noise. The lowest interference setting that achieves the desired improvement should be used to remove interference from the screen. Correcting installation issues that cause noise is the best way to eliminate interference. Color Limit: Hides part of the color palette to help eliminate fields of weak clutter. By setting the color limit to the color of the undesired returns, you can eliminate the display of undesired returns on the screen. Smoothing: Removes noise that is not part of a normal sonar return, and adjusts the appearance of returns, such as the bottom. When smoothing is set to high, more of the low-level noise remains than when using the interference control, but the noise is more subdued because of averaging. Smoothing can remove speckle from the bottom. Smoothing and interference work well together to eliminate low-level noise. You can adjust the interference and smoothing settings incrementally to remove undesirable noise from the display. 17 Sonar Appearance Settings Sonar Alarm Settings FI NOTE: Some settings require external accessories. Select Settings > Alarms > Sonar. Shallow Water: Sets an alarm to sound when the depth is less than the specified value. Deep Water: Sets an alarm to sound when the depth is greater than the specified value. Water Temp.: Sets an alarm to sound when the transducer reports a temperature that is 2°F (1.1°C) above or below the specified temperature. Contour: Sets an alarm to sound when the transducer detects a suspended target within the specified depth from the surface of the water and from the bottom. Fish Alarm: Sets an alarm to sound when the transducer detects a suspended target within the specified depth range and the specified color range. Advanced Sonar Settings From a sonar view, select Menu > Sonar Menu > Sonar Setup > Advanced. Transmit: Stops the transducer from transmitting. Shift: Allows you to set the depth range on which the sonar is focused. This allows you to zoom in a higher resolution in the focused depth. When using shift, bottom tracking may not work effectively, because the sonar looks for data within the depth range of the focused area, which may not include the bottom. Using shift also can impact the scroll speed, because data outside the depth range of the focused area is not processed, which reduces the time required to receive and display the data. You can zoom in to the focused area, which enables you to evaluate target returns more closely at a higher resolution than just zooming alone. 18 Transducer Installation Settings From a sonar view, select Menu > Sonar Menu > Sonar Setup > Installation. Transmit Rate: Sets the length of time between sonar pings. Increasing the transmit rate increases the scroll speed, but it may also increase self-interference. Reducing the transmit rate increases the spacing between transmit pulses and can resolve self-interference. Transmit Power: Reduces transducer ringing near the surface. A lower transmit power value reduces transducer ringing. Filter Width: Defines the edges of the target. A shorter filter defines the edges of the targets, but may allow more noise. A longer filter creates softer target edges, and may also reduce noise. Transducer Diagnostics: Shows details about the transducer. Flip Left/Right: Changes the SideVü view orientation from left to right. EN NOTE: Not all options and settings apply to all models and transducers. From a Sonar view, select Menu > Sonar Menu > Sonar Setup > Appearance. Color: Sets the color scheme and color gain. Overlay Data: Sets the data shown on the sonar screen. A-Scope: Displays a vertical flasher along the right side of the screen that shows instantaneously the range to targets along a scale. Depth Line: Shows a quick-reference depth line. Edge: Highlights the strongest signal from the bottom to help define the hardness or softness of the signal. Pic. Advance: Allows the sonar picture to advance faster by drawing more than one column of data on the screen for each column of sounder data received. This is especially helpful when you are using the sounder in deep water, because the sonar signal takes longer to travel to the water bottom and back to the transducer. The 1/1 setting draws one column of information on the screen per sounder return. The 2/1 setting draws two columns of information on the screen per sounder return, and so on for the 4/1 and 8/1 settings. Echo Stretch: Adjusts the size of the echoes on the screen to make it easier to see separate returns on the screen. When targets are difficult to see, echo stretch makes the target returns more pronounced and easier to see on the screen. If the echo stretch value is too high, the targets blend together, and if the value is too low, the targets might be small and difficult to see. You can use echo stretch and filter width together to obtain the preferable resolution and noise reduction. With echo stretch and filter width set to low, the display has the highest resolution, but is the most susceptible to noise. With echo stretch set to high and filter width set to low, the display has a lower resolution, but has wider targets. With echo stretch and filter width set to high, the display has the lowest resolution, but is the least susceptible to noise. It is not recommended to set echo stretch to low and filter width to high. Bottom Track: Sets the frequency used for determining depth. The bottom tracking control allows you to select the specific channel that is used to track the bottom. For example, you can set the bottom tracking for the low frequency for deep water operation. Temp. Source: Sets the channel for the water temperature log when more than one water-temperature sensor or temperature-capable transducer is connected. TI AL Surface Noise: Hides surface noise to help reduce clutter. Wider beam widths (lower frequencies) can show more targets, but can generate more surface noise. TVG: Adjusts the time varying gain, which can reduce noise. This control is best used for situations when you want to control and suppress clutter or noise near the water surface. It also allows for the display of targets near the surface that are otherwise hidden or masked by surface noise. Sonar Recordings Recording the Sonar Display NOTE: Not all models support sonar recording. 1 Insert a memory card into the card slot. 2 From a sonar view, select Menu > Sonar Setup > Sonar Recording > Record Sonar. 15 minutes of sonar recording uses approximately 200 MB of space of the inserted memory card. You can record sonar until the card reaches capacity. Stopping the Sonar Recording Before you can stop recording sonar, you must begin recording it (Recording the Sonar Display). From a sonar view, select Menu > Sonar Setup > Sonar Recording > Stop Recording. Deleting a Sonar Recording 1 Insert a memory card into the card slot. 2 From a sonar view, select Menu > Sonar Setup > Sonar Recordings > View Recordings. 3 Select a recording. 4 Select Delete. Sonar Before you can play back the sonar recordings, you must download and install the HomePort™ application and record sonar data onto a memory card. 1 Remove the memory card from the device. 2 Insert the memory card into a card reader attached to a computer. 3 Open the HomePort application. 4 Select a sonar recording from your device list. 5 Right-click the sonar recording in the lower pane. 6 Select Playback. Radar WARNING The marine radar transmits microwave energy that has the potential to be harmful to humans and animals. Before beginning radar transmission, verify that the area around the radar is clear. The radar transmits a beam approximately 12° above and below a line extending horizontally from the center of the radar. When the radar is transmitting, do not look directly at the antenna at close range; eyes are the most sensitive part of the body to electromagnetic energy. NOTE: As a safety feature, the radar enters standby mode after it warms up. This gives you an opportunity to verify the area around the radar is clear before beginning radar transmission. 1 With the chartplotter off, connect your radar as described in the radar installation instructions. 2 Turn on the chartplotter. The radar warms up and a countdown alerts you when the radar is ready. 3 Select Radar. 4 Select a radar mode. A countdown message appears while the radar is starting up. 5 Select Menu > Transmit Radar. Adjusting the Radar Range The range of the radar signal indicates the length of the pulsed signal transmitted and received by the radar. As the range increases, the radar transmits longer pulses in order to reach distant targets. Closer targets, especially rain and waves, also reflect the longer pulses, which can add noise to the Radar screen. Viewing information about longer-range targets can also decrease the amount of space available on the Radar screen for viewing information about shorter-range targets. • Select to decrease the range. • Select to increase the range. EN NOTE: Not all models support radar. When you connect your compatible chartplotter to an optional Garmin marine radar, such as a GMR™ 1226 xHD2 or a GMR 24 HD, you can view more information about your surroundings. The GMR transmits a narrow beam of microwave energy as it rotates to a 360° pattern. When the transmitted energy contacts a target, some of that energy is reflected back to the radar. Transmitting Radar Signals TI AL Playing Sonar Recordings Radar Display Modes FI NOTE: Not all modes are available with all radar devices and all chartplotters. Select Radar. Cruising Mode: Shows a full-screen image of the gathered radar information. Harbor Mode: Intended for use in inland waters, this mode works best with short-range signals (2 nm or less). Offshore Mode: Intended for use in open waters, this mode works best with long-range signals. Sentry Mode: Allows you to put the radar into timed-transmit mode, in which you can configure a radar transmit and standby cycle to conserve power. You can also enable a guard zone in this mode, which identifies a safe zone around your boat. If you switch from Sentry mode to another mode, the radar switches to full-time transmission and disables all guard zones. Radar Overlay Mode: Shows a full-screen image of the gathered radar information on top of the Navigation chart. The Radar overlay displays data based on the most recently used radar mode. Dual Range Mode: Provides a side-by-side view of both shortrange and long-range radar data. Changing the Radar Mode 1 From a combination screen or SmartMode layout with radar, select Menu > Radar Menu > Change Radar. 2 Select a radar mode. Tips for Selecting a Radar Range • Determine what information you need to see on the Radar screen. For example, do you need information about nearby weather conditions or targets and traffic, or are you more concerned about distant weather conditions? • Assess the environmental conditions where the radar is being used. Especially in inclement weather, longer-range radar signals can increase the clutter on the Radar screen and make it more difficult to view information about shorter-range targets. In rain, shorter-range radar signals can enable you to view information about nearby objects more effectively, if the rain clutter setting is configured optimally. • Select the shortest effective range, given your reason for using radar and the present environmental conditions. Zooming In and Out of the Radar Screen • Pinch two fingers together to zoom out. • Spread two fingers apart to zoom in. • Drag the screen to pan, and then select necessary. or to zoom, if Marking a Waypoint on the Radar Screen 1 From a Radar screen or the Radar overlay, select a location. 2 Select Create Waypoint. Sentry Mode Sentry mode allows you to put the radar into timed-transmit mode, in which you can configure a radar transmit and standby cycle to conserve power. You can also enable a guard zone in this mode, which identifies a safe zone around your boat and sounds an alarm when a radar object enters the zone. Sentry mode works with all Garmin GMR model radars. Enabling Timed Transmit From the sentry screen, select Menu > Radar Menu > Sentry Setup > Timed Transmit > On. Radar 19 Enabling a Guard Zone Dangerous target is in range. A red ring flashes from the target while an alarm sounds and a message banner appears. After the alarm has been acknowledged, a solid red dot with a dashed red line attached to it indicates the location and the projected course over ground or the GPS heading of the target. If the safezone collision alarm has been set to Off, the target flashes, but the audible alarm does not sound and the alarm banner does not appear. Assigning a MARPA Tag to an Object Before you can use MARPA, you must have a heading sensor connected and an active GPS signal. The heading sensor must provide the NMEA 2000 parameter group number (PGN) 127250 or the NMEA 0183 HDM or HDG output sentence. 1 From the Harbor, Offshore, or Cruising Radar screen, select an object or location. Select Acquire Target > MARPA Target. EN Before you can define the boundaries of the guard zone, you must enable a guard zone (Enabling a Guard Zone). You can define a circular guard zone that completely encompasses your boat. 1 From the sentry screen, select Menu > Radar Menu > Sentry Setup > Adjust Guard Zone > Adjust Guard Zone > Circle. 2 Select the location of the outer guard zone circle. 3 Select the location of the inner guard zone circle to define the width of the guard zone. FI You can define the boundaries of a guard zone that does not completely encompass your boat. 1 From the sentry screen, select Menu > Radar Menu > Sentry Setup > Adjust Guard Zone > Adjust Guard Zone > Corner 1. 2 Touch and drag the location of the outer guard-zone corner À. 3 Select Corner 2. 4 Touch the location of the inner guard-zone corner Á to define the width of the guard zone. Target has been acquired. A solid green ring indicates the location of a target that the radar has locked onto. A dashed green line attached to the circle indicates the projected course over ground or the GPS heading of the target. Closest point of approach and time to closest point of approach to a dangerous target. Defining a Circular Guard Zone Radar Targeting and MARPA Acquiring a target. Concentric, dashed green rings radiate from the target while the radar is locking onto it. Target has been lost. A solid green ring with an X through it indicates that the radar could not lock onto the target. From the sentry screen, select Menu > Radar Menu > Sentry Setup > Enable Guard Zone. Defining a Partial Guard Zone MARPA Targeting Symbols TI AL Setting the Standby and Transmit Times Before you can set the standby and transmit times, you must enable timed transmit (Enabling Timed Transmit). To help conserve power, you can indicate the radar standby time and the transmit time to implement periodic radar signal transmissions at set intervals. 1 From the sentry screen, select Menu > Radar Menu > Sentry Setup. 2 Select Stdby Time. 3 Enter the time interval between radar signal transmissions. 4 Select Transmit Time. 5 Enter the duration of each radar signal transmission. Radar targeting enables you to identify and track objects. Mini-automatic radar plotting aid (MARPA) is primarily used for collision avoidance. To use MARPA, you assign a MARPA tag to a target. The radar system automatically tracks the tagged object and provides you with information about the object, including the range, bearing, speed, GPS heading, nearest approach, and time to nearest approach. MARPA indicates the status of each tagged object (acquiring, lost, tracking, or dangerous), and the chartplotter can sound a collision alarm if the object enters your safe zone. Viewing Information about a MARPA-tagged Object You can view the range, bearing, speed, and other information about a MARPA-tagged object. 1 From a radar screen, select a targeted object. 2 Select MARPA Target. Removing a MARPA Tag from a Targeted Object 1 From the Radar screen, select a MARPA target. 2 Select MARPA Target > Remove. Viewing a List of AIS and MARPA Threats From any Radar screen or the Radar overlay, you can view and customize the appearance of a list of AIS and MARPA threats. 1 From a Radar screen, select Menu > Radar Menu > Other Vessels > List > Show. 2 Select the type of threats to include in the list. Showing AIS Vessels on the Radar Screen AIS requires the use of an external AIS device and active transponder signals from other vessels. You can configure how other vessels appear on the Radar screen. If any setting (except the AIS display range) is configured for one radar mode, the setting is applied to every other radar mode. The details and projected heading settings configured for one radar mode are applied to every other radar mode and to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu > Radar Menu > Other Vessels > Display Setup. 2 Select an option: • To indicate the distance from your location within which AIS vessels appear, select Display Range, and select a distance. • To show details about AIS-activated vessels, select Details > Show. • To set the projected heading time for AIS-activated vessels, select Proj. Heading, and enter the time. VRM and EBL The variable range marker (VRM) and the electronic bearing line (EBL) measure the distance and bearing from your boat to a 20 Radar Showing the VRM and the EBL The VRM and the EBL configured for one mode are applied to other radar modes. NOTE: The VRM and the EBL cannot be changed in sentry mode. From a Radar screen, select Menu > Radar Menu > Show VRM/EBL. Adjusting the VRM and the EBL Before you can adjust the VRM and the EBL, you must show them on the Radar screen (Showing the VRM and the EBL). You can adjust the diameter of the VRM and the angle of the EBL, which moves the intersection point of the VRM and the EBL. The VRM and the EBL configured for one mode are applied to all other radar modes. 1 From a Radar screen, select a new location for the intersection point of the VRM and the EBL. 2 Select Drop VRM/EBL. 3 Select Stop Pointing. Radar Overlay FI When you connect your chartplotter to an optional Garmin marine radar, you can use the Radar overlay to overlay radar information on the Navigation chart or on the Fishing chart. The Radar overlay superimposes radar information on the Navigation chart or the Fishing chart. Data appears on the Radar overlay based on the most recently used radar mode (such as Harbor, Offshore, or Sentry), and all settings configurations applied to the Radar overlay are also applied to the last-used radar mode. For example, if you use Harbor mode and then you switch to the Radar overlay, the Radar overlay would show Harbor mode radar data. If you changed the gain setting using the Radar overlay menu, the gain setting for Harbor mode would change automatically. Radar Overlay and Chart Data Alignment When using the Radar overlay, the chartplotter aligns radar data with chart data based on the boat heading, which is based by default on data from a magnetic heading sensor connected using a NMEA 0183 or NMEA 2000 network. If a heading sensor is not available, the boat heading is based on GPS tracking data. GPS tracking data indicates the direction in which the boat is moving, not the direction in which the boat is pointing. If the boat is drifting backward or sideways due to a current or wind, the Radar overlay may not perfectly align with the chart data. This situation should be avoided by using boat-heading data from an electronic compass. If the boat heading is based on data from a magnetic heading sensor or an automatic pilot, the heading data could be compromised due to incorrect setup, mechanical malfunction, magnetic interference, or other factors. If the heading data is compromised, the Radar overlay may not align perfectly with the chart data. Radar Setting a Custom Park Position If you have more than one radar on your boat, you must be viewing the radar screen for the radar you want to adjust. By default, the antenna is stopped perpendicular to the pedestal when it is not spinning. You can adjust this position. 1 From the radar screen, select Menu > Radar Setup > Antenna Configuration > Park Position. 2 Use the slider bar to adjust the position of the antenna when stopped, and select Back. Enabling and Adjusting a Radar No Transmit Zone You can indicate an area within which the radar scanner does not transmit signals. NOTE: This feature is not available on all radar and chartplotter models. 1 From a radar screen, select Menu > Radar Menu > Radar Setup > Enable No Transmit Zone. The no-transmit zone is indicated by a shaded area on the radar screen. 2 Select Adjust No Transmit Zone > Move No Transmit Zone. 3 Select Angle 1, and select the new location for the first angle. 4 Select Angle 2, and select the new location for the second angle. 5 Select Done. EN Measuring the Range and Bearing to a Target Object Before you can adjust the VRM and the EBL, you must show them on the Radar screen (Showing the VRM and the EBL). 1 From a Radar screen, select the target location. 2 Select Measure Distance. The range and the bearing to the target location appear in the upper-left corner of the screen. Showing the Radar Overlay The radar overlay displays data based on the most recently used radar mode. Select Charts > Radar Overlay. The radar picture appears in orange and overlays the navigation chart. TI AL target object. On the Radar screen, the VRM appears as a circle that is centered on the present location of your boat, and the EBL appears as a line that begins at the present location of your boat and intersects the VRM. The point of intersection is the target of the VRM and the EBL. Stopping the Transmission of Radar Signals From a Radar screen, select Menu > Radar Menu > Radar To Standby. TIP: Press from any screen to quickly stop radar transmission. Optimizing the Radar Display You can adjust the radar display settings for reduced clutter and increased accuracy. NOTE: You can optimize the radar display for each radar mode. 1 Select a radar range (Adjusting the Radar Range). 2 Restore the default value of the gain setting (Adjusting Gain on the Radar Screen Automatically). 3 Adjust the gain setting manually (Adjusting Gain on the Radar Screen Manually). Radar Gain and Clutter Adjusting Gain on the Radar Screen Automatically The automatic gain setting for each radar mode is optimized for that mode, and may differ from the automatic gain setting used for another mode. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. NOTE: Not all options and settings are available on all radar and chartplotter models. 1 From a radar screen or the radar overlay, select Menu > Radar Menu > Gain. 21 • To set the gain automatically once, based on average conditions, the range of the radar signal, and the selected radar mode, select Auto. The chartplotter does not adjust the gain automatically in response to changing conditions. • To adjust the gain automatically for changing conditions, select Auto Low or Auto High. • To adjust the gain automatically to show birds over the surface of the water, select Auto Bird. Adjusting Rain Clutter on the Radar Screen You can adjust the appearance of clutter caused by rain. Reducing the radar range also can minimize rain clutter (Zooming In and Out of the Radar Screen). The rain clutter setting affects the appearance of nearby rain clutter and targets more than it affects the appearance of distant rain clutter and targets. A higher rain clutter setting reduces the appearance of clutter caused by nearby rain, but it can also reduce or eliminate the appearance of nearby targets. NOTE: Depending upon the radar in use, the rain clutter settings configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu > Radar Menu > Noise Rejection > Rain Clutter. 2 Select Up or Down to decrease or increase the appearance of nearby rain clutter until other targets are clearly visible on the Radar screen. Clutter caused by rain may still be visible. EN Adjusting Gain on the Radar Screen Manually For optimal radar performance, you can manually adjust the gain. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu > Radar Menu > Gain. 2 Select Up to raise the gain, until light speckles appear across the Radar screen. Data on the Radar screen is refreshed every few seconds. As a result, the effects of manually adjusting the gain may not appear instantly. Adjust the gain slowly. Select Down to lower the gain until the speckles disappear. 4 If boats, land, or other targets are within range, select Down to lower the gain until the targets begin to blink. 5 Select Up to raise the gain until the boats, land, or other targets appear steadily lit on the Radar screen. 6 Minimize the appearance of nearby large objects, if necessary. 7 Minimize the appearance of side-lobe echoes, if necessary. NOTE: Depending upon the radar in use, the sea clutter setting configured for use in one radar mode may or may not be applied to other radar modes or to the radar overlay. NOTE: Not all options and settings are available on all radar and chartplotter models. 1 From a radar screen or the radar overlay, select Menu > Radar Menu > Noise Rejection > Sea Clutter. 2 Select Presets or Auto. 3 Select a setting that reflects the present sea conditions. When using a compatible radar model, the chartplotter adjusts the sea clutter based on the sea conditions automatically. TI AL 2 Select an applicable option for the connected radar: FI Minimizing Nearby Large-Object Interference Nearby targets of significant size, such as jetty walls, can cause a very bright image of the target to appear on the Radar screen. This image can obscure smaller targets located near it. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu > Radar Menu > Gain. 2 Select Down to lower the gain until the smaller targets are clearly visible on the Radar screen. Reducing the gain to eliminate nearby large-object interference may cause smaller or distant targets to blink or disappear from the Radar screen. Minimizing Side-Lobe Interference on the Radar Screen Side-lobe interference may appear to streak outward from a target in a semi-circular pattern. Side-lobe effects can be avoided by reducing the gain or reducing the radar range. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu > Radar Menu > Gain. 2 Select Down to lower the gain until the semi-circular, streaked pattern disappears from the Radar screen. Reducing the gain to eliminate side-lobe interference may cause smaller or distant targets to blink or disappear from the Radar screen. Adjusting Sea Clutter on the Radar Screen Automatically You can set the chartplotter to automatically adjust the appearance of clutter caused by choppy sea conditions. 22 Reducing Cross Talk Clutter on the Radar Screen You can reduce the appearance of clutter caused by interference from another nearby radar source, when the cross talk reject setting is on. NOTE: Depending upon the radar in use, the cross talk reject setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. From a Radar screen or the Radar overlay, select Menu > Radar Menu > Noise Rejection > Crosstalk Rej.. Echo Trails The echo trails feature enables you to track the movement of vessels on the radar display. You can change the length of time the trail is displayed. NOTE: Depending upon the radar in use, the settings configured for use in one radar mode may or may not be applied to other radar modes or to the radar overlay. NOTE: Not all options and settings are available on all radar and chartplotter models. Turning on Echo Trails From a radar screen or the radar overlay, select Menu > Radar Menu > Radar Setup > Echo Trails > Display. Adjusting the Length of the Echo Trails 1 From a radar screen or the radar overlay, select Menu > Radar Menu > Radar Setup > Echo Trails > Time. 2 Select the length of the trail. Clearing the Echo Trails You can remove the echo trails from the radar screen to reduce the clutter the screen. From a radar screen or the radar overlay, select Clear Trails. Radar Display Settings From any Radar screen or the Radar overlay, select Menu > Radar Menu > Radar Setup. Radar Radar Appearance Settings From a Radar screen, select Menu > Radar Menu > Radar Setup > Appearance. NOTE: These settings do not apply to the Radar overlay. Color Scheme: Sets the color scheme. Look-Ahead Speed: Shifts your present location toward the bottom of the screen automatically as your speed increases. Enter your top speed for the best results. Heading Line: Shows an extension from the bow of the boat in the direction of travel on the radar screen. Rings: Shows the range rings that help you to visualize distances on the radar screen. Nav Lines: Shows the navigation lines that indicate the course you have set using Route To, Guide To, or Go To. Waypoints: Shows waypoints on the radar screen. safely operating your boat. Avoid navigational hazards and never leave the helm unattended. Always be prepared to promptly regain manual control of your boat. Learn to operate the autopilot on calm and hazard-free open water. Use caution when operating the autopilot near hazards in the water, such as docks, pilings, and other boats. The autopilot system continuously adjusts the steering of your boat to maintain a constant heading (heading hold). The system also allows manual steering and several modes of automaticsteering functions and patterns. Opening the Autopilot Screen TI AL Orientation: Sets the perspective of the radar display. The orientation setting applies to every radar mode. This setting does not apply to the Radar overlay. Appearance: Sets the color scheme, look-ahead speed, and navigation appearance. Front of Boat: Compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. Before you can open the autopilot screen, you must have a compatible autopilot installed and configured. Select A/V, Gauges, Controls > Autopilot. Autopilot Screen Front-of-Boat Offset EN The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. FI Measuring the Potential Front-of-Boat Offset The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. 1 Using a magnetic compass, take an optical bearing of a stationary target located within viewable range. 2 Measure the target bearing on the radar. 3 If the bearing deviation is more than +/- 1°, set the front-ofboat offset. Setting the Front-of-Boat Offset Before you can set the front-of-boat offset, you must measure the potential front-of-boat offset. The front-of-boat offset setting configured for use in one radar mode is applied to every other radar mode and to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu > Radar Menu > Radar Setup > Front of Boat. 2 Select Up or Down to adjust the offset. Selecting a Different Radar Source 1 Select an option: • From a radar screen or the radar overlay, select Menu > Radar Menu > Radar Setup > Source. • Select Settings > Communications > Preferred Data Source > Radar. 2 Select the radar source. Autopilot WARNING You can use the autopilot feature only at a station installed next to a helm, throttle, and helm control device. You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of Autopilot À Á  Actual heading à Rudder position indicator (This functionality is available only when a rudder sensor is connected.) Intended heading (heading the autopilot is steering toward) Actual heading (when in standby mode) Intended heading (when engaged) Adjusting the Step Steering Increment 1 From the Autopilot screen, select Menu > Autopilot Setup > Steering Mode > Step Turn Size. 2 Select an increment. Setting the Power Saver You can adjust the level of rudder activity. 1 From the Autopilot screen, select Menu > Autopilot Menu > Autopilot Setup > Power Saver. 2 Select a percentage. Selecting a higher percentage reduces rudder activity at the expense of heading performance. The higher the percentage, the more the course deviates before the autopilot corrects it. TIP: In choppy conditions at low speeds, increasing the Power Saver percentage reduces rudder activity. Enabling Shadow Drive™ NOTE: The Shadow Drive feature is available only on hydraulic steering systems. From the Autopilot screen, select Menu > Autopilot Menu > Autopilot Setup > Shadow Drive > Enabled. Engaging the Autopilot When you engage the autopilot, the autopilot takes control of the helm and steers the boat to maintain your heading. From any screen, select Engage. 23 Adjusting the Heading with the Helm NOTE: You must enable the Shadow Drive feature before you can adjust the heading using the helm (Enabling Shadow Drive™). With the autopilot engaged, manually steer the boat. The autopilot activates Shadow Drive mode. When you release the helm and manually maintain a specific heading for a few seconds, the autopilot resumes a heading hold at the new heading. Adjusting the Heading with the Chartplotter in Step Steering Mode Before you can steer your boat using the keys at the bottom of the autopilot screen, you must engage the autopilot (Engaging the Autopilot). • Select <1° or 1°> to initiate a single 1° turn. • Select <<10° or 10°>> to initiate a single 10° turn. • Hold <1° or 1°> to initiate a rate-controlled turn. The boat continues to turn until you let go of the key. • Hold <<10° or 10°>> to initiate a sequence of 10° turns. Steering Patterns The autopilot can steer the boat in preset patterns for fishing, and it can also perform other specialty maneuvers such as Uturns and Williamson turns. Following the U-Turn Pattern FI You can use the u-turn pattern to turn the boat around 180° and maintain the new heading. 1 Form the autopilot screen, select Menu > Autopilot Menu > Pattern Steering > U-Turn > Engage. 2 Select Engage Port or Engage Starboard. Setting Up and Following the Circles Pattern You can use the circles pattern to steer the boat in a continuous circle, in a specified direction, and at a specified time interval. 1 From the Autopilot screen, select Menu > Autopilot Menu > Pattern Steering > Circles. 2 If necessary, select Time, and select a time for the autopilot to steer one complete circle. Select Engage Port or Engage Starboard. Setting Up and Following the Zigzag Pattern You can use the zigzag pattern to steer the boat from port to starboard and back, over a specified time and angle, across your present heading. 1 From the Autopilot screen, select Menu > Autopilot Menu > Pattern Steering > Zigzag. 2 If necessary, select Amplitude, and select a degree. 3 If necessary, select Period, and select a length of time. 4 Select Engage Zigzag. Following the Williamson Turn Pattern You can use the Williamson turn pattern to steer the boat around with the intent of running alongside the location where the Williamson turn pattern was initiated. The Williamson turn pattern can be used in man overboard situations. 24 Pattern Steering > Williamson Turn. 2 Select Engage Port or Engage Starboard. Following an Orbit Pattern You can use the orbit pattern to steer the boat in a continuous circle around the active waypoint. The size of the circle is defined by your distance from the active waypoint when you begin the orbit pattern. 1 From the Autopilot screen, select Menu > Autopilot Menu > Pattern Steering > Orbit. 2 Select Engage Port or Engage Starboard. Setting Up and Following the Cloverleaf Pattern You can use the cloverleaf pattern to steer the boat to repeatedly pass over an active waypoint. When you begin the cloverleaf pattern, the autopilot drives the boat toward the active waypoint and begins the cloverleaf pattern. You can adjust the distance between the waypoint and the location where the autopilot turns the boat for another pass over the waypoint. The default setting turns the boat at a range of 1000 ft. (300 m) from the active waypoint. 1 From the Autopilot screen, select Menu > Autopilot Menu > Pattern Steering > Cloverleaf. 2 If necessary, select Length, and select a distance. 3 Select Engage Port or Engage Starboard. Setting Up and Following a Search Pattern EN WARNING You are responsible for the safe operation of your boat. Do not begin a pattern until you are certain that the water is clear of obstacles. 1 From the Autopilot screen, select Menu > Autopilot Menu > TI AL Your intended heading shows in the center of the Autopilot screen. You can use the search pattern to steer the boat in increasingly larger circles outward from the active waypoint, forming a spiral pattern. When you begin the search pattern, the autopilot drives the boat to the active waypoint and begins the pattern. You can adjust the distance between each circle in the spiral. The default distance between circles is 50 ft. (20 m). 1 From the Autopilot screen, select Menu > Autopilot Menu > Pattern Steering > Search. 2 If necessary, select Search Spacing, and select a distance. 3 Select Engage Port or Engage Starboard. Cancelling a Steering Pattern • Physically steer the boat. NOTE: Shadow Drive must be enabled to cancel a steering pattern by physically steering the boat. • Select or to cancel a pattern using step steering mode. • Select Standby. Digital Selective Calling Networked Chartplotter and VHF Radio Functionality If you have a NMEA 0183 VHF radio or a NMEA 2000 VHF radio connected to your chartplotter, these features are enabled. • The chartplotter can transfer your GPS position to your radio. If your radio is capable, GPS position information is transmitted with DSC calls. • The chartplotter can receive digital selective calling (DSC) distress and position information from the radio. • The chartplotter can track the positions of vessels sending position reports. If you have a Garmin NMEA 2000 VHF radio connected to your chartplotter, these features are also enabled. • The chartplotter allows you to quickly set up and send individual routine call details to your Garmin VHF radio. Digital Selective Calling Turning On DSC Select Settings > Other Vessels > DSC. DSC List The DSC list is a log of the most recent DSC calls and other DSC contacts you have entered. The DSC list can contain up to 100 entries. The DSC list shows the most recent call from a boat. If a second call is received from the same boat, it replaces the first call in the call list. Viewing the DSC List Before you can view the DSC list, the chartplotter must be connected to a VHF radio that supports DSC. Select Info > DSC List. Adding a DSC Contact Incoming Distress Calls FI If your compatible chartplotter and VHF radio are connected using NMEA 0183 or NMEA 2000, your chartplotter alerts you when your VHF radio receives a DSC distress call. If position information was sent with the distress call, that information is also available and recorded with the call. designates a distress call in the DSC list and marks the position of the vessel on the Navigation chart at the time of the DSC distress call. Navigating to a Vessel in Distress designates a distress call in the DSC list and marks the position of a vessel on the Navigation chart at the time of the DSC distress call. 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Navigate To. 4 Select Go To or Route To. Man-Overboard Distress Calls Initiated from a VHF Radio When the chartplotter is connected to a compatible VHF radio with NMEA 2000, and you initiate a man-overboard DSC distress call from the radio, the chartplotter shows the manoverboard screen and prompts you to navigate to the manoverboard point. If you have a compatible autopilot system connected to the network, the chartplotter prompts you to start a Williamson’s turn to the man-overboard point. If you cancel the man-overboard distress call on the radio, the chartplotter screen prompting you to activate navigation to the man-overboard location disappears. Man-Overboard and SOS Distress Calls Initiated from the Chartplotter When your chartplotter is connected to a Garmin NMEA 2000 compatible radio and you mark an SOS or man-overboard location, the radio shows the Distress Call page so you can quickly initiate a distress call. Digital Selective Calling Position Tracking When you connect the chartplotter to a VHF radio using NMEA 0183, you can track vessels that send position reports. This feature is also available with NMEA 2000, when the vessel sends the correct PGN data (PGN 129808; DSC Call Information). Every position report call received is logged in the DSC list (DSC List). Viewing a Position Report 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review. 4 Select an option: • To switch to a Navigation chart marking the location, select Next Page. • To view the position report details, select Previous Page. Navigating to a Tracked Vessel 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Navigate To. 4 Select Go To or Route To. EN You can add a vessel to your DSC list. You can make calls to a DSC contact from the chartplotter. 1 Select Info > DSC List > Add Contact. 2 Enter the Maritime Mobile Service Identity (MMSI) of the vessel. 3 Enter the name of the vessel. For information on placing distress calls from your radio, see the VHF radio owner’s manual. For information about marking an MOB or SOS location, see Marking an SOS Location. TI AL • When you initiate a man-overboard distress call from your radio, the chartplotter shows the man-overboard screen and prompts you to navigate to the man-overboard point. • When you initiate a man-overboard distress call from your chartplotter, the radio shows the Distress Call page to initiate a man-overboard distress call. Creating a Waypoint at the Position of a Tracked Vessel 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Create Waypoint. Editing Information in a Position Report 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Edit. To enter the name of the vessel, select Name. To select a new symbol, select Symbol, if available. To enter a comment, select Comment. To show a trail line for the vessel if your radio is tracking the position of the vessel, select Trail. • To select a color for the trail line, select Trail Line. • • • • Deleting a Position-Report Call 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Clear Report. Viewing Vessel Trails on the Chart You can view trails for all tracked vessels on some chart views. By default, a black line indicates the path of the vessel, a black dot indicates each previously reported position of a tracked vessel, and a blue flag indicates the last reported position of the vessel. 1 From a chart or 3D chart view, select Menu > Chart Setup > Other Vessels > DSC > DSC Trails. 2 Select the number of hours to show tracked vessels on the chart. For example, if you select 4 Hours, all trail points that are less than four hours old appear for all tracked vessels. 25 Selecting a DSC Channel NOTE: The selection of a DSC channel is limited to those channels that are available in all frequency bands. The default channel is 72. If you select a different channel, the chartplotter uses that channel for subsequent calls until you call using another channel. 1 Select Info > DSC List. 2 Select a vessel or a station to call. 3 Select Review > Call with Radio > Channel. 4 Select an available channel. Making an Individual Routine Call • To set the minimum value of the standard operating range, select Rated Min.. • To set the maximum value of the standard operating range, select Rated Max.. • To set the lower limit of the gauge lower than the rated minimum, select Scale Min.. • To set the upper limit of the gauge higher than the rated maximum, select Scale Max.. Select the limit value. 6 Repeat steps 4 and 5 to set additional gauge limits. Viewing Engine and Fuel Gauges Before you can view engine and fuel gauges, you must be connected to a NMEA 2000 network capable of sensing engine and fuel data. See the installation instructions for details. Select A/V, Gauges, Controls > Engines. Selecting the Number of Engines Shown in Gauges You can show information for up to four engines. 1 From the engine gauges screen, select Menu > Gauge Setup > Engine Selection > Num. Engines. 2 Select an option: • Select the number of engines. • Select Auto Configure to automatically detect the number of engines. EN NOTE: When initiating a call from the chartplotter, if the radio does not have an MMSI number programmed, the radio will not receive call information. 1 Select Info > DSC List. 2 Select a vessel or a station to call. 3 Select Review > Call with Radio. 4 If necessary, select Channel, and select a new channel. 5 Select Send. The chartplotter sends information about the call to the radio. 6 On your Garmin VHF radio, select Call. 3 Select Mode > Custom. 4 Select an option: TI AL Individual Routine Calls When you connect the chartplotter to a Garmin VHF radio, you can use the chartplotter interface to set up an individual routine call. When setting up an individual routine call from your chartplotter, you can select the DSC channel on which you want to communicate. The radio transmits this request with your call. Making an Individual Routine Call to an AIS Target 1 From a chart or 3D chart view, select an AIS target. 2 Select AIS Vessel > Call with Radio. 3 If necessary, select Channel, and select a new channel. 4 Select Send. FI The chartplotter sends information about the call to the radio. On your Garmin VHF radio, select Call. Gauges and Graphs The gauges and graphs provide various information about the engine and environment. To view the information, a compatible transducer or sensor must be connected to the network. Viewing the Gauges 1 Select A/V, Gauges, Controls. 2 Select a gauge. 3 Select or to view a different gauge page. Changing the Data Shown in a Gauge 1 From a gauges screen, hold a gauge. 2 Select a data type. 3 Select the data to display. Customizing Engine Gauge and Fuel Gauge Limits You can configure the upper and lower limits and the range of desired standard operation of a gauge. When a value exceeds the range of standard operation, the gauge becomes red. NOTE: Not all options are available for all gauges. 1 From the engine gauges screen, select Menu > Gauge Setup > Set Gauge Limits. 2 Select a gauge. 26 Customizing the Engines Shown in Gauges Before you can customize how the engines are shown in the gauges, you must manually select the number of engines (Selecting the Number of Engines Shown in Gauges). 1 From the engine gauges screen, select Menu > Gauge Setup > Engine Selection > Edit Engines. 2 Select First Engine. 3 Select the engine to display in the first gauge. 4 Repeat for the remaining engine bars. Enabling Status Alarms for Engine Gauges You can enable the chartplotter to display engine status alarms. From the engine gauges screen, select Menu > Gauge Setup > Status Alarms > On. When an engine alarms is triggered, a gauge status alarm message appears and the gauge may become red depending on the type of alarm. Enabling Some Engine Gauge Status Alarms 1 From the engine gauges screen, select Menu > Gauge Setup > Status Alarms > Custom. 2 Select one or more engine gauge alarms to turn on or off. Setting the Fuel Alarm Before you can set a fuel level alarm, a compatible fuel flow sensor must be connected to the NMEA 2000 network. You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify. 1 Select Settings > Alarms > Fuel > Fuel Level Alarm > On. 2 Enter the remaining amount of fuel that triggers the alarm. Setting the Fuel Capacity of the Vessel 1 Select Settings > My Vessel > Fuel Capacity. 2 Enter the combined total capacity of the fuel tanks. Gauges and Graphs You can synchronize the fuel levels in the chartplotter with the actual fuel in the vessel when you add fuel to your vessel. 1 Select A/V, Gauges, Controls > Engines > Menu. 2 Select an option: • After you have filled up all the fuel tanks on the vessel, select Fill Up All Tanks. The fuel level is reset to maximum capacity. • After you have added less than a full tank of fuel, select Add Fuel to Boat, and enter the amount added. • To specify the total fuel in the vessel tanks, select Set Total Fuel Onboard, and enter the total amount of fuel in the tanks. Viewing the Wind Gauges Before you can view wind information, you must have a wind sensor connected to the chartplotter. Select A/V, Gauges, Controls > Wind. Configuring the Sailing Wind Gauge Configuring the Speed Source FI You can specify whether the vessel speed data displayed on the gauge and used for wind calculations is based on water speed or GPS speed. 1 From the wind gauge, select Menu > Compass Gauge > Speed Display. 2 Select an option: • To calculate the vessel speed based on data from the water-speed sensor, select Water Speed. • To calculate the vessel speed based on GPS data, select GPS Speed. Configuring the Heading Source of the Wind Gauge You can specify the source of the heading displayed on the wind gauge. Magnetic heading is the heading data received from a heading sensor, and GPS heading is calculated by your chartplotter GPS (course over ground). 1 From the wind gauge, select Menu > Compass Gauge > Heading Source. 2 Select GPS Hdg. or Magnetic. NOTE: When moving at low speeds or when stationary, the magnetic compass source is more accurate than the GPS source. Customizing the Close-Hauled Wind Gauge You can specify the range of the close-hauled wind gauge for both the upwind scale and the downwind scale. 1 From the wind gauge, select Menu > Compass Gauge > Gauge Type > Close Hauled Gauge. 2 Select an option: • To set the maximum and minimum values that appear when the upwind close-hauled wind gauge appears, select Change Upwind Scale, and set the angles. • To set the maximum and minimum values that appear when the downwind close-hauled wind gauge appears, select Change Downwind Scale, and set the angles. Tide, Current, and Celestial Information Viewing Trip Gauges Trip gauges show information for odometer, speed, time, and fuel for your present trip. Select Info > Trip & Graphs > Trip. Resetting Trip Gauges 1 Select Info > Trip & Graphs > Trip. 2 Select an option: • To set all the readings for the present trip to zero, select Reset Trip. • To set the maximum speed reading to zero, select Reset Maximum Speed. • To set the odometer reading to zero, select Reset Odometer. • To set all the readings to zero, select Reset All. Viewing Graphs Before you can view graphs of various environmental changes, such as temperature, depth, and wind, you must have an appropriate transducer or sensor connected to the network. Select Info > Trip & Graphs > Graphs. Setting the Graph Range and Time Scales You can indicate the amount of time and the range of depth that appear in the depth and water temperature graphs. 1 From a graph, select Graph Setup. 2 Select an option: • To set a time-elapsed scale, select Duration. The default setting is 10 minutes. Increasing the time-elapsed scale allows you to view variations over a longer period of time. Decreasing the time-elapsed scale allows you to view more detail over a shorter period of time. • To set the graph scale, select Scale. Increasing the scale allows you to view more variation in readings. Decreasing the scale allows you to view more detail in the variation. EN You can configure the sailing wind gauge to show true or apparent wind speed and angle. 1 From the wind gauge, select Menu > Sailing Wind Gauge. 2 Select an option: • To show true or apparent wind angle, select Needle, and select an option. • To show true or apparent wind speed, select Wind Speed, and select an option. • To view true or apparent wind, select Wind, and select an option. TI AL Synchronizing the Fuel Data with the Actual Vessel Fuel Tide, Current, and Celestial Information Tide Station Information You can view information about a tide station for a specific date and time, including the tide height, and when the next high and low tides will occur. By default, the chartplotter shows tide information for the most recently viewed tide station and for the present date and time. Select Info > Tides & Currents > Tides. Current Station Information NOTE: Current station information is available with certain detailed maps. You can view information about a current station for a specific date and time, including the current speed and level of the current. By default, the chartplotter shows current information for the most recently viewed current station and for the present date and time. Select Info > Tides & Currents > Currents. Celestial Information You can view information about sunrise, sunset, moonrise, moonset, moon phase, and the approximate sky view location of the sun and moon. The center of the screen represents the sky 27 overhead, and the outermost rings represent the horizon. By default, the chartplotter shows celestial information for the present date and time. Select Info > Tides & Currents > Celestial. Viewing Tide Station, Current Station, or Celestial Information for a Different Date 1 Select Info > Tides & Currents. 2 Select Tides, Currents, or Celestial. 3 Select an option. Opening the Media Player Before you can open the media player, you must connect a compatible device to the chartplotter. Select A/V, Gauges, Controls > Media. NOTE: Not all devices have these icons. Viewing Almanac Information from the Navigation Chart 1 From a chart or 3D chart view, select a location. 2 Select Information. 3 Select Tides, Currents, or Celestial. Description Saves or deletes a channel as a preset Repeats all songs TI AL Select Info > Tides & Currents. Select Tides or Currents. Select Nearby Stations. Select a station. Icon Repeats one song Searches for stations or skips songs Shuffles Selecting the Media Source When you have multiple media devices connected on a network, such as the NMEA 2000 network, you can select the media source you want to control from your chartplotter. NOTE: You can play media only from sources that are connected to the device. NOTE: Not all features are available on all media sources. 1 From the media screen, select Source. NOTE: The source menu appears only for devices that support multiple media sources. 2 Select a source. EN Viewing Information for a Different Tide or Current Station FI Warning Manager Viewing Messages ® Icons • To view information for a different date, select Change Date > Manual, and enter a date. • To view information for today, select Change Date > Current. • If available, to view information for the day after the date shown, select Next Day. • If available, to view information for the day before the date shown, select Previous Day. chartplotter and iPod can be connected using a FUSION-Link capable stereo. 1 Select Info > Warning Manager. 2 Select a message. 3 Select Review. Sorting and Filtering Messages Playing Music Browsing for Music 1 From the media screen, select Browse or Menu > Browse. 2 Select Select or select an option. Enabling Alphabetical Search You can enable the alphabetical search feature to find a song or album in a large list. From the media screen, select Menu > Media Menu > Installation > Alpha Search. Setting a Song to Repeat 1 While playing a song, select Menu > Media Menu > Repeat. 2 If necessary, select Single. Saving Messages to a Memory Card Setting All Songs to Repeat Clearing all of the Messages Setting Songs to Shuffle 1 From the media screen, select Menu > Media Menu > 1 Select Info > Warning Manager > Sort/Filter. 2 Select an option to sort or filter the message list. 1 Insert a memory card into the card slot. 2 Select Info > Warning Manager > Save to Card. Select Info > Warning Manager > Clear Warning Manager. Media Player NOTE: The media player feature is not compatible with all chartplotter models. If you have a FUSION-Link™ capable stereo connected to the NMEA 2000 network, you can control the stereo using the chartplotter. The chartplotter should automatically detect the media player when it is first connected. You can play media from sources connected to the media player and sources connected to the NMEA 2000 network. Your 28 From the media screen, select Menu > Media Menu > Repeat > All. Shuffle. 2 If necessary, select an option. Listening to the Radio Saving a Channel as a Preset You can save up to 15 AM stations and 15 FM stations as presets. 1 From the AM, FM, or VHF page, tune the device to a channel. 2 Select Presets > Add Current Channel. Removing a Channel Preset 1 Tune the device to a channel. Warning Manager Channel. Changing the Tuning Mode You can change how you select a station for some media types, such as FM or AM radio. NOTE: Not all tuning modes are available for all media sources. 1 From the media screen, select Menu > Media Menu > Tuning Mode. Select an option. 3 If necessary, select Select. Setting the Tuner Region 1 From the media screen, select Menu > Media Menu > Installation > Tuner Region. 2 Select an option. Opening the MTP Source Before you can open the MTP source, you must connect your MTP device to a compatible media device. You can access music on your Media Transfer Protocol (MTP) device, such as an Android™ device. You can also charge your phone or media player while it is connected and playing music. 1 Connect your MTP source through USB, such as the stereo, the external USB plug, or an external dock. 2 From the media screen, select Source > MTP. Enabling and Disabling Zones FI If you have wired your vessel's speakers into zones, you can enable needed zones and disable unused zones. 1 From the media screen, select Menu > Media Menu > Audio Levels > Enable/Disable Zones. 2 Select a zone. Muting the Media Volume 1 From the media screen, select 2 If necessary, select Select. Scanning VHF Channels Before you can scan VHF channels, you must set the source to VHF. You can monitor VHF channels saved as presets for activity and automatically switch to an active channel. From the VHF media screen, select Scan. Adjusting the VHF Squelch NOTE: Your media player must support VHF radio to use this feature. 1 From the VHF source page, select Menu > Media Menu > Squelch. 2 Use the slider bar to adjust the VHF squelch. SiriusXM Satellite Radio ® When you have a FUSION-Link capable stereo and SiriusXM Connect Tuner installed and connected to the chartplotter, you may have access to SiriusXM satellite radio, depending on your subscription. Locating a SiriusXM Radio ID Before you can activate your SiriusXM subscription, you must have the radio ID of your SiriusXM Connect Tuner. You can locate the SiriusXM Radio ID on the back of the SiriusXM Connect Tuner, on the back of its packaging, or by tuning your chartplotter to channel 0. 1 Select Media > Source > SiriusXM. Media Player The SiriusXM radio ID does not include the letters I, O, S, or F. Activating a SiriusXM Subscription Before you can activate the SiriusXM subscription, you must have the Radio ID (Locating a SiriusXM Radio ID). 1 With the SiriusXM source selected, tune to channel 1. You should be able to hear the preview channel. If not, check the SiriusXM Connect Tuner and antenna installation and connections, and try again. 2 Tune to channel 0 to locate the Radio ID. 3 Contact SiriusXM listener care by phone at (866) 635-2349 or go to www.siriusxm.com/activatenow to subscribe in the United States. Contact SiriusXM by phone at (877) 438-9677 or go to www.siriusxm.ca/activatexm to subscribe in Canada. 4 Provide the Radio ID. The activation process usually takes 10 to 15 minutes, but can take up to an hour. For the SiriusXM Connect Tuner to receive the activation message, it must be turned on and receiving the SiriusXM signal. 5 If the service is not activated within the hour, go to http://care.siriusxm.com/refresh or contact SiriusXM by phone at 1-855-MYREFRESH (697-3373). Customizing the Channel Guide SiriusXM radio channels are grouped in categories. You can select the categories of channels that appear in the channel guide. NOTE: This feature is available with a GXM™ 52 antenna. 1 Select Media > Category. 2 Select a category. EN Adjusting the Volume 2 Tune to channel 0. TI AL 2 Select Menu > Media Menu > Presets > Remove Current Saving a SiriusXM Channel to the Presets List You can save your favorite channels to the presets list. 1 Select Media. 2 Select the channel you want to save as a preset. 3 Select Menu > Presets > Add Current Channel. Unlocking SiriusXM Parental Controls 1 From the media screen, select Browse > Parental > Unlock. 2 Enter your passcode. The default passcode is 0000. Setting Parental Controls on SiriusXM Radio Channels Before you can set parental controls, the parental controls must be unlocked. The parental control feature allows you to limit access to any SiriusXM channels, including those with mature content. When enabled, the parental control feature requires you to enter a passcode to tune to the locked channels. Select Browse > Parental > Lock/Unlock. A list of channels appears. A checkmark indicates a locked channel. NOTE: When you view the channels after setting parental controls, the display changes: indicates a locked channel. • • indicates an unlocked channel. Changing a Parental Passcode on a SiriusXM Radio Before you can change the passcode, the parental controls must be unlocked. 1 From the media screen, select Browse > Parental > Change PIN. 2 Enter your passcode and select Done. 3 Enter a new passcode. 29 Restoring Default Parental Control Settings Values This process deletes all the settings information you have entered. When you restore the parental control settings to their default values, the passcode value is reset to 0000. 1 From the media menu, select Installation > Factory Defaults. 2 Select Yes. Clearing All Locked Channels on a SiriusXM Radio Before you can clear all locked channels, the parental controls must be unlocked. 1 From the media screen, select Browse > Parental > Clear All Locked. 2 Enter your passcode. Setting the Device Name Changing the Weather Chart 1 From a combination screen or SmartMode layout with a weather chart, select Menu > Weather Menu > Change Weather. 2 Select a weather chart. Viewing Precipitation Information Precipitation ranging from very light rain and snow, up to strong thunderstorms, is indicated in varying shades and colors. Precipitation is shown either independently or with other weather information. Select Charts > Precipitation. The time stamp in the upper-left corner of the screen indicates the elapsed time since the weather data provider last updated the information. TI AL 4 Confirm the new passcode. Precipitation Views 1 From the media screen, select Menu > Media Menu > Installation > Set Device Name. 2 Enter a device name. 3 Select Select or Done. SiriusXM Weather EN WARNING The weather information provided through this product is subject to service interruptions and may contain errors, inaccuracies, or outdated information, and consequently should not be relied upon exclusively. Always use common sense while navigating, and check alternate weather information sources prior to making safety-related decisions. You acknowledge and agree that you shall be solely responsible for use of the weather information and all decisions taken with respect to navigating in weather. Garmin will not be responsible for any consequences of using SiriusXM weather information. From the precipitation weather chart, select Menu > Weather Menu. Radar Loop: Shows precipitation information as an image of the latest update or as an animated loop of the latest updates. The time stamp indicates the elapsed time since the service provider generated the weather radar frame currently displayed on the screen. Cloud Cover: Shows cloud cover data. Waypoints: Shows waypoints. Legend: Shows the weather legend. FI NOTE: SiriusXM data is not available in all regions. A Garmin SiriusXM satellite weather receiver and antenna receives satellite weather data and shows it on various Garmin devices, including the Navigation chart on a compatible chartplotter. The weather data for each feature comes from reputable weather data centers such as the National Weather Service and the Hydrometeorological Prediction Center. For more information, go to www.siriusxm.com/sxmmarine. SiriusXM Equipment and Subscription Requirements To use satellite weather, you must have a compatible satellite weather receiver. To use SiriusXM satellite radio, you must have a compatible satellite radio receiver. Go to www.garmin.com for more information. You must also have a valid subscription to receive satellite weather and radio. For more information, refer to the instructions for your satellite weather and radio equipment. Weather Data Broadcasts Weather data is broadcast at different intervals for each weather feature. For example, radar is broadcast at five-minute intervals. When the Garmin receiver is turned on, or when a different weather feature is selected, the receiver must receive new data before it can be shown. You might experience a delay before weather data or a different feature appears on the chart. NOTE: Any weather feature can change in appearance if the source that provides the information changes. 30 Storm Cell and Lightning Information on the weather precipitation Storm cell are represented by chart. They indicate both the present position of a storm and the projected path of that storm in the immediate future. Red cones appear with a storm cell icon, and the widest part of each cone points in the direction of the projected path of the storm cell. The red lines in each cone indicate where the storm will most likely be in the near future. Each line represents 15 minutes. Lightning strikes are represented by . Lightning appears on the weather precipitation chart if strikes were detected within the last seven minutes. The ground-based lightning detection network detects cloud-to-ground lightning only. NOTE: This feature is not available on all devices and in all subscriptions. Hurricane Information The weather Precipitation chart can show the present position of a hurricane , a tropical storm, or a tropical depression. A red line stemming from a hurricane icon indicates the projected path of the hurricane. Darkened dots on the red line indicate the projected locations through which the hurricane will pass, as received from the weather data provider. Weather Warnings and Weather Bulletins When a marine weather warning, weather watch, weather advisory, weather bulletin, or other weather statement is issued, shading indicates the area to which the information applies. The aqua lines on the chart indicate the boundaries of marine forecasts, coastal forecasts, and offshore forecasts. Weather bulletins may consist of either weather watches or weather advisories. To view information about the warning or bulletin, select the shaded area. Color Marine Weather Group Cyan Flash Flood Blue Flood SiriusXM Weather Color Marine Weather Group Red Marine Yellow Severe Storm Red Tornado Symbol Weather Viewing Forecast Information for Another Time Period 1 Select Charts > Forecast. 2 Select an option: • To view the weather forecast for the next 48 hours, in 12hour increments, select Next Forecast multiple times. • To view the weather forecast for the previous 48 hours, in 12-hour increments, select Previous Forecast multiple times. Weather Fronts and Pressure Centers Weather fronts appear as lines that indicate the leading edge of an air mass. Description Cold front Occluded front Trough Pressure-center symbols often appear near weather fronts. FI Indicates a low-pressure center, which is a region of relatively lower pressure. Moving away from a lowpressure center results in increased pressure. Winds flow counterclockwise around low-pressure centers in the northern hemisphere. Indicates a high-pressure center, which is a region of relatively higher pressure. Moving away from a highpressure center results in decreased pressure. Winds flow clockwise around high-pressure centers in the northern hemisphere. Viewing a Marine Forecast or an Offshore Forecast 1 Select Charts > Forecast. 2 Pan the chart to an offshore location. The Marine Forecast or Offshore Forecast options appear when forecast information is available. 3 Select Marine Forecast or Offshore Forecast. City Forecasts City forecasts appear as weather symbols. The forecast is viewed in 12-hour increments. Symbol Weather Partly cloudy Fair (sunny, hot, clear) Cloudy Rain (drizzle, sleet, showers) Windy Foggy SiriusXM Weather Wind Barb Wind Speed Wind Barb Wind Speed Calm 20 knots 5 knots 50 knots 10 knots 65 knots EN Stationary front Symbol Weather Surface Winds Surface wind vectors appear on the Sea Conditions chart using wind barbs that indicate the direction from which the wind is blowing. A wind barb is a circle with a tail. The line or flag attached to the tail of the wind barb indicates the wind speed. A short line represents 5 knots, a long line represents 10 knots, and triangle represents 50 knots. 15 knots Warm front Description Viewing Sea Conditions The Sea Conditions feature shows information about surface conditions, including winds, wave height, wave period, and wave direction. Select Charts > Sea Conditions. TI AL The Forecast chart shows city forecasts, marine forecasts, warnings, hurricane warnings, METARS, county warnings, weather fronts and pressure centers, surface pressure, and weather buoys. PressureCenter Symbol Snow (snow showers, flurries, blizzard, blowing snow, sleet, freezing rain, freezing drizzle) Smoke (dusty, hazy) Forecast Information Front Symbol Symbol Weather Thunderstorms Wave Height, Wave Period, and Wave Direction Wave heights for an area appear as variations in color. Different colors indicate different wave heights, as shown in the legend. The wave period indicates the time (in seconds) between successive waves. Wave period lines indicate areas that have the same wave period. Wave directions appear on the chart using red arrows. The direction of each arrow pointer indicates the direction in which a wave is moving. Viewing Forecast Sea Conditions Information for Another Time Period 1 Select Charts > Sea Conditions. 2 Select an option: • To view forecasted sea conditions for the next 36 hours, in 12-hour increments, select Next Forecast multiple times. • To view the forecasted sea conditions for the previous 36 hours, in 12-hour increments, select Previous Forecast multiple times. Viewing Fishing Information The weather Fishing chart shows present water temperature, present surface pressure conditions, and fishing forecasts. Select Charts > Fishing. Surface Pressure and Water Temperature Data Surface-pressure information appears as pressure isobars and pressure centers. Isobars connect points of equal pressure. Pressure readings can help to determine weather and wind conditions. High-pressure areas are generally associated with fair weather. Low-pressure areas are generally associated with clouds and the chance of precipitation. Isobars packed closely together show a strong pressure gradient. Strong pressure gradients are associated with areas of stronger winds. Pressure units are shown in millibars (mb), inches of Mercury (inHg), or hectopascals (hPa). Colored shading indicates the surface temperature of the water, as shown in the legend in the corner of the display. 31 Changing the Sea Surface Temperature Color Range Visibility Information FI Visibility is the forecast maximum horizontal distance that can be seen at the surface, as shown in the legend on the left of the screen. Variations in the visibility shading show the forecast change in surface visibility. NOTE: This feature is not available on all devices and in all subscriptions. Select Charts > Visibility. Viewing Forecast Visibility Information for Another Time Period 1 Select Charts > Visibility. 2 Select an option: • To view the visibility forecast for the next 36 hours, in 12hour increments, select Next Forecast multiple times. • To view the visibility forecast for the previous 36 hours, in 12-hour increments, select Previous Forecast multiple times. Viewing Buoy Reports Report readings are taken from buoys and coastal observation stations. These readings are used to determine air temperature, dew point, water temperature, tide, wave height and period, wind direction and speed, visibility, and barometric pressure. 1 From a weather chart, select . 2 Select Buoy. Viewing Local Weather Information near a Buoy You can select an area near a buoy to view forecast information. 1 From a weather chart, select a location on the chart. 2 Select Local Weather. 3 Select an option: • To view present weather conditions from a local weather service, select Current Cond.. 32 Creating a Waypoint on a Weather Chart 1 From a weather chart, select a location. 2 Select Create Waypoint. Weather Overlay The weather overlay superimposes weather and weather-related information on the Navigation chart, the Fishing chart, and the Perspective 3D chart view. The Navigation chart and the Fishing chart can show weather radar, height of cloud tops, lightning, weather buoys, county warnings, and hurricane warnings. The Perspective 3D chart view can show weather radar. Weather overlay settings configured for use on one chart are not applied to another chart. The weather overlay settings for each chart must be configured separately. NOTE: The offshore Fishing chart is available with premium charts, in some areas. Turning On the Weather Overlay on a Chart From the Navigation chart or Fishing chart, select Menu > Chart Setup > Weather > Weather > On. EN You can change the color range dynamically to view higher resolution sea surface temperature readings. 1 From the weather Fishing chart, select Menu > Weather Menu > Sea Temperature. 2 Select an option: • To allow the chartplotter to adjust the temperature range automatically, select Auto Configure. The chartplotter automatically finds the lower and upper limits for the current screen, and updates the temperaturecolor scale. • To enter the lower and upper limits for the temperature range, select Lower Limit or Upper Limit, and enter the lower or upper limit. • To view a local weather forecast, select Forecast. • To view surface wind and barometric pressure information, select Sea Surface. • To view wind and wave information, select Marine Bulletin. TI AL Forecasting Fish Locations You can show areas that contain optimal weather conditions for specific species of fish. NOTE: This feature is not available on all devices and in all subscriptions. 1 From the weather Fishing chart, select Menu > Weather Menu > Fish Species. 2 Select a species of fish. 3 Select On. 4 Repeat steps 2 and 3 to show areas with optimal weather conditions for additional species of fish. Shaded areas indicate optimal fishing areas. If you have selected more than one species of fish, you can select a shaded area to view the fish species that are included in the shaded area. Weather Overlay Settings on the Navigation Chart From the Navigation chart, select Menu > Chart Setup > Weather. Weather: Turns on and off the weather overlay. Precipitation: Shows precipitation data. Cloud Cover: Shows cloud cover data. Visibility: Shows visibility data. Buoys: Shows weather buoys. Legend: Shows the weather legend. Weather Overlay Settings on the Fishing Chart NOTE: Available settings depend on the receiver connected to your device. From the Fishing chart, select Menu > Chart Setup > Weather. Precipitation: Shows precipitation radar. Fish Species: Shows locations of a specific species of fish. Sea Temperature: Shows sea temperature data. Buoys: Shows weather buoys. Legend: Shows the weather legend. Viewing Weather Subscription Information You can view information about the weather services you have subscribed to and how many minutes have passed since the data for each service was updated. From a weather chart, select Menu > Weather Subscription. Viewing Video Before you can view video, you must connect to a compatible source. Compatible devices include video devices connected to the ports on the chartplotter, as well as supported network (IPbased) video cameras, encoders, and thermal cameras. Select A/V, Gauges, Controls > Video. Viewing Video 1 From the video screen, select Menu > Source. 2 Select the source of the video feed. Alternating Among Multiple Video Sources If you have two or more video sources, you can alternate between them using a specific time interval. 1 From the video screen, select Menu > Source > Alternate. 2 Select Time, and select the amount of time each video appears. 3 Select Source, and select the video sources to add to the alternating sequence. Networked Video Devices NOTICE A Garmin Power over Ethernet (PoE) Isolation Coupler (P/N 010-10580-10) must be used when connecting a PoE device, such as a FLIR camera, to a Garmin Marine Network. Connecting a PoE device directly to a Garmin Marine Network chartplotter damages the Garmin chartplotter and may damage the PoE device. ® Video Settings Some cameras provide additional setup options. NOTE: Not all options are available on all camera models and chartplotter models. You may need to update the camera software to use this feature. From the video screen, select Menu > Video Setup. Set Input: Associates the camera with a video source. Mirror: Reverses the image like a rearview mirror. Standby: Places the camera in standby mode to conserve power and protect the lens when not in use. Home Position: Sets the home position of the camera. Scan Speed: Sets how quickly the camera moves during a scan. Scan Width: Sets the width of the image captured by the camera during a scan. Name: Allows you to enter a new name for this camera. FLIR™ Menu: Provides access to the settings for the camera. EN Before you can view and control video devices such as IP cameras, encoders, and thermal cameras using your chartplotter, you must have a compatible video device connected to your chartplotter, and you must have a marine network cable Power over Ethernet (PoE) isolation coupler. Go to www.garmin.com for a list of compatible devices or to purchase a PoE Isolation Coupler. You can connect multiple supported video cameras and up to two video encoders to the Garmin Marine Network. You can select and view up to four video sources at once. Chartplotters with multiple composite built-in video inputs can display a single built-in video input only. When the cameras are connected, the network detects them automatically and displays them in the source list. available features. You may need to update the camera software to use this feature. From the infrared video screen, select Menu. IR/Visible: Displays an infrared or visible camera image. Scan: Surveys the surrounding area. Freeze: Pauses the camera image. Change Colors: Selects the color scheme of the infrared image. Change Scene: Selects the infrared image mode, such as day, night, MOB, or docking. Video Setup: Opens more video options. TI AL Selecting a Video Source Using Video Presets on Networked Video Cameras FI You can save, name, and activate video presents for each networked video source. Saving Video Presets on a Networked Video Camera 1 From a video screen, touch the screen. The video controls appear on the screen. 2 Hold a video preset button. A green light indicates the setting is stored. Naming Video Presets on a Networked Video Camera 1 From a video screen, select Menu > Video Setup > Presets. 2 Select a preset. 3 Select Rename. 4 Enter preset name. Activating Video Presets on a Networked Video Camera You can quickly return networked cameras to preset values. 1 From a video screen, touch the screen. The video controls appear on the screen. 2 Select a video preset. The camera restores the video settings saved for that preset. TIP: You can also save and activate presets using the video menu. Camera Settings Some cameras provide additional options to control the camera view. NOTE: Not all options are available on all camera models and chartplotter models. Refer to the camera manual for a list of Viewing Video Associating the Camera to a Video Source You may need to associate the camera with a video source. 1 From the video screen, select Menu > Video Menu > Source. 2 Select the camera. 3 Select Video Setup > Set Input. 4 Select the video input. Video Camera Movement Control NOTICE Do not aim the camera at the sun or extremely bright objects. Damage to the lens may occur. Always use the chartplotter controls or buttons to pan and tilt the camera. Do not manually move the camera unit. Manually moving the camera may damage the camera. NOTE: This feature is available only when a compatible camera is connected. You may need to update the camera software to use this feature. You can control the movements of the connected video cameras that support panning, tilting, and zooming. Controlling Video Cameras Using On-Screen Controls On-screen controls allow you to control pan-tilt-zoom (PTZ) cameras. Refer to the camera manual for a list of available features. 1 From a video screen, touch the screen. The video controls appear on the screen. 2 Select an option: • To zoom in and out, use the zoom button. • To pan or tilt the camera, use the compass rose. TIP: Hold in the compass rose to continue to move the camera in the desired direction. 33 Creating a Combination with Video Functions Configuring the Video Appearance FI NOTE: Not all options are available on all camera models and chartplotter models. 1 From the video screen, select Menu > Video Setup. 2 Select an option: • To show the video using a stretched aspect ratio, select Aspect > Stretch. The video cannot be stretched beyond the dimensions provided by the connected video device, and it may not fill the entire screen. • To show the video using a standard aspect ratio, select Aspect > Standard. • To adjust the brightness, select Brightness, and select Up, Down, or Auto. • To adjust the color saturation, select Saturation, and select Up, Down, or Auto. • To adjust the contrast, select Contrast, and select Up, Down, or Auto. • To allow the chartplotter to automatically select the source format, select Standard > Auto. Configuring the PC Display Before you can configure the PC display mode, you must set the video source to analog or digital PC. 1 When in PC display mode, select anywhere on the screen. 2 Select an option: • To adjust the screen brightness, select the brightness arrows. • To adjust the screen contrast, select the contrast arrows. 34 The video source changes to Video 1. Device Configuration Turning On the Chartplotter Automatically You can set the chartplotter to turn on automatically when the power is applied. Otherwise, you must turn on the chartplotter by pressing . Select Settings > System > Auto Power Up. NOTE: When Auto Power Up is On, and the chartplotter is turned off using , and power is removed and reapplied within less than two minutes, you may need to press to restart the chartplotter. System Settings Select Settings > System. Simulator: Turns the simulator on or off and allows you to set the time, date, speed, and simulated location. Beeper and Display: Adjusts the display and sound settings. GPS: Provides information about the GPS satellites and settings. System Information: Provides information about the devices on the network and the software version. Station Information: Adjusts the setup of the station. Auto Power Up: Turns the device on automatically when power is applied. EN You can include up to four video functions in a custom combination screen. If your device has multiple built-in video connections, you can use one built-in source for one function within each combination. NOTE: The video source displays all connected, supported video devices. You can select Show All to see a list of all possible video inputs or video encoder channels that are not connected to a video input source. 1 Select Combos > Menu > Add Combo. 2 Select Functions, and select a number. 3 Select an area to assign a function to, select Video, and select a video source. 4 Repeat step 3 for all video functions in the combination screen. 5 If necessary, customize the combination screen (Adding a Custom Combination Screen). Exiting PC Display Mode 1 When in PC display mode, select anywhere on the screen. 2 Select the display mode icon in the upper-left corner. TI AL Controlling a Video Camera Using Gestures When a networked video camera supports gesture responses, you can control pan-tilt-zoom cameras using gestures directly on the chartplotter screen. Check your camera user manual for a list of available features. TIP: Using gestures allows video control without displaying the video controls. 1 From a video screen, touch the screen. 2 Select an option: • To zoom in and out with the camera, use pinch and zoom gestures. • To pan or tilt the camera, swipe the screen in the desired direction. Station Settings Select Settings > System > Station Information. Change Station: Sets the entire station to a new set of defaults based on the location of this station. You can also select to use this display as a stand-alone, individual display, instead of grouping it with other displays to make a station. GRID™ Pairing: Allows you to pair a GRID™ remote input device with this station. Display Order: Sets the order of the displays, which is important when using a GRID remote input device. Reset Stations: Restores the factory default layouts for all displays in the station. Viewing System Software Information You can view the software version, the basemap version, any supplemental map information (if applicable), the software version for an optional Garmin radar (if applicable), and the unit ID number. You may need this information to update the system software or to purchase additional map data information. Select Settings > System > System Information. Viewing the Event Log The event log shows a list of system events. Select Settings > System > System Information > Event Log. Preferences Settings Select Settings > Preferences. Units: Sets units of measure. Language: Sets the on-screen text language. Navigation: Sets navigation preferences. Keyboard Layout: Arranges the keys on the on-screen keyboard. Device Configuration Units Settings Navigation Settings FI NOTE: Some settings and options require additional charts or hardware. Select Settings > Preferences > Navigation. Route Labels: Sets the type of labels shown with route turns on the map. Turn Transition: Adjusts how the chartplotter transitions to the next turn or leg or the route. You can set the transition to be based on time or distance before the turn. You can increase the time or distance value to help improve the accuracy of the autopilot when navigating a route or an Auto Guidance line with many frequent turns or at higher speeds. For straighter routes or slower speeds, lowering this value can improve autopilot accuracy. Auto Guidance: Sets the measurements for the Safe Depth, Safe Height, and Shoreline Distance, when you are using some premium maps. Route Start: Selects a starting point for route navigation. Auto Guidance Line Configurations CAUTION The Safe Depth and Safe Height settings influence how the chartplotter calculates an Auto Guidance line. If an area has an unknown water depth or an unknown obstacle height, the Auto Guidance line is not calculated in that area. If an area at the beginning or the end of an Auto Guidance line is shallower than the safe water depth or lower than the safe obstacle height, the Auto Guidance line is not calculated in that area. On the chart, the course through those areas appears as a gray line. When your boat enters one of those areas, a warning message appears. NOTE: Auto Guidance is available with premium charts, in some areas. You can set the parameters the chartplotter uses when calculating an Auto Guidance line. Safe Depth: Sets the minimum depth (chart depth datum) the chartplotter uses when calculating an Auto Guidance line. NOTE: The minimum safe depth for the premium charts is 3 feet. If you enter a Safe Depth value of less than 3 feet, the Device Configuration Adjusting the Distance from Shore The Shoreline Distance setting indicates how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for the Shoreline Distance setting are relative, not absolute. To ensure the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway. 1 Dock your vessel or drop the anchor. 2 Select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Normal. 3 Select a destination that you have navigated to previously. 4 Select Navigate To > Auto Guidance. 5 Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. 6 Select an option: • If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. • If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Far. • If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Near. 7 If you selected Near or Far in step 6, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 8 Select an option: • If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. • If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Farthest. • If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Nearest. 9 If you selected Nearest or Farthest in step 8, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to EN Select Settings > Preferences > Units. System Units: Sets the unit format for the device. Variance: Sets the magnetic declination, the angle between magnetic north and true north, for your present location. North Reference: Sets the direction references used in calculating heading information. True sets geographic north as the north reference. Grid sets grid north as the north reference (000º). Magnetic sets the magnetic north as the north reference. Position Format: Sets the position format in which a given location reading appears. Do not change this setting unless you are using a map or chart that specifies a different position format. Map Datum: Sets the coordinate system on which the map is structured. Do not change this setting unless you are using a map or chart that specifies a different map datum. Time: Sets the time format, time zone, and daylight saving time. charts only use depths of 3 feet for Auto Guidance route calculations. Safe Height: Sets the minimum height (chart height datum) of a bridge that your boat can safely travel under. Shoreline Distance: Sets how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for this setting are relative, not absolute. To ensure that the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway (Adjusting the Distance from Shore). TI AL Screenshot Capture: Allows the device to save images of the screen. User Data Sharing: Allows you to share waypoints and routes over the Garmin Marine Network. All chartplotters that share waypoints and routes must have this setting turned on. Menu Bar Display: Shows or automatically hides the menu bar when it is not needed. 35 Communications Settings NMEA 0183 Settings Setting Alarms Navigation Alarms Select Settings > Alarms > Navigation. Arrival: Sets an alarm to sound when you are within a specified distance or time from a turn or a destination. Anchor Drag: Sets an alarm to sound when you exceed a specified drift distance while anchored. Off Course: Sets an alarm to sound when you are off course by a specified distance. System Alarms Alarm Clock: Sets an alarm clock. Unit Voltage: Sets an alarm to sound when the battery reaches a specified low voltage. GPS Accuracy: Sets an alarm to sound when the GPS location accuracy falls outside the user-defined value. Setting the Fuel Alarm Before you can set a fuel level alarm, a compatible fuel flow sensor must be connected to the NMEA 2000 network. You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify. 1 Select Settings > Alarms > Fuel > Fuel Level Alarm > On. 2 Enter the remaining amount of fuel that triggers the alarm. EN Select Settings > Communications > NMEA 0183 Setup. Port Types: See Setting the Communication Format for Each NMEA 0183 Port. Output Sentences: See Configuring NMEA 0183 Output Sentences. Position Precision: Adjusts the number of digits to the right of the decimal point for transmission of NMEA output. XTE Precision: Adjusts the number of digits to the right of the decimal point for NMEA crosstalk error output. Waypoint IDs: Sets the device to transmit waypoint names or numbers via NMEA 0183 while navigating. Using numbers may resolve compatibility issues with older NMEA 0183 autopilots. Defaults: Restores the NMEA 0183 settings to the original factory defaults. Diagnostics: Displays NMEA 0183 diagnostic information. Network to receive data from and share data with other Garmin Marine Network-compatible devices and chartplotters. TI AL Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 10 Repeat steps 3 through 9 at least once more, using a different destination each time, until you are familiar with the functionality of the Shoreline Distance setting. Configuring NMEA 0183 Output Sentences You can enable and disable NMEA 0183 output sentences. 1 Select Settings > Communications > NMEA 0183 Setup > Output Sentences. 2 Select an option. 3 Select one or more NMEA 0183 output sentences, and select Back. 4 Repeat steps 2 and 3 to enable or disable additional output sentences. FI Setting the Communication Format for Each NMEA 0183 Port You can configure the communication format for each internal NMEA 0183 port when connecting your chartplotter to external NMEA 0183 devices, a computer, or other Garmin devices. 1 Select Settings > Communications > NMEA 0183 Setup > Port Types. 2 Select an input or output port. 3 Select a format: • To support the input or output of standard NMEA 0183 data, DSC, and sonar NMEA input support for the DPT, MTW, and VHW sentences, select NMEA Std.. • To support the input or output of standard NMEA 0183 data for most AIS receivers, select NMEA High Speed. • To support the input or output of Garmin proprietary data for interfacing with Garmin software, select Garmin. 4 Repeat steps 2–3 to configure additional input or output ports. NMEA 2000 Settings Select Settings > Communications > NMEA 2000 Setup. Device List: Displays the devices connected to the network. Label Devices: Changes the labels for available connected devices. Garmin Marine Network The Garmin Marine Network allows you to share data from Garmin peripheral devices with the chartplotters quickly and easily. You can connect a chartplotter to a Garmin Marine 36 Setting Weather Alarms Before you can set weather alarms, you must have a compatible chartplotter connected to a weather device, such as a GXM device, and have a valid weather subscription. 1 Select Settings > Alarms > Weather. 2 Turn on alarms for specific weather events. My Vessel Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > My Vessel. Keel Offset: Offsets the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location (Setting the Keel Offset). Temperature Offset: Compensates for the water temperature reading from a NMEA 0183 water-temperature sensor or a temperature-capable transducer (Setting the Water Temperature Offset). Calibrate Water Speed: Calibrates the speed-sensing transducer or sensor (Calibrating a Water Speed Device). Fuel Capacity: Sets the combined fuel capacity of all the fuel tanks on your vessel (Setting the Fuel Capacity of the Vessel). Vessel Type: Enables some chartplotter features based on the boat type. Setting the Keel Offset You can enter a keel offset to compensate the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location. Enter a positive number to offset for a keel. You can enter a negative number to compensate for a large vessel that may draw several feet of water. 1 Complete an action, based on the location of the transducer: • If the transducer is installed at the water line À, measure the distance from the transducer location to the keel of the Device Configuration boat. Enter this value in steps 3 and 4 as a positive number. • If the transducer is installed at the bottom of the keel Á, measure the distance from the transducer to the water line. Enter this value in steps 3 and 4 as a negative number. Setting the Vessel Type You can select your boat type to configure the chartplotter settings and to use features customized for your boat type. 1 Select Settings > My Vessel > Vessel Type. 2 Select Powerboat or Sailboat. Other Vessels Settings Setting the Water Temperature Offset Restoring the Original Chartplotter Factory Settings FI Before you can set the water temperature offset, you must have a NMEA 0183 water-temperature sensor or a temperaturecapable transducer to measure water temperature. The temperature offset compensates for the temperature reading from a temperature sensor. 1 Measure the water temperature using the temperature sensor or temperature-capable transducer that is connected to the chartplotter. 2 Measure the water temperature using a different temperature sensor or a thermometer that is known to be accurate. 3 Subtract the water temperature measured in step 1 from the water temperature measured in step 2. This is the temperature offset. Enter this value in step 5 as a positive number if the sensor connected to the chartplotter measures the water temperature as being colder than it actually is. Enter this value in step 5 as a negative number if the sensor connected to the chartplotter measures the water temperature as being warmer than it actually is. 4 Select Settings > My Vessel > Temperature Offset. 5 Enter the temperature offset calculated in step 3. Calibrating a Water Speed Device If you have a speed-sensing transducer connected to the chartplotter, you can calibrate that speed-sensing device to improve the accuracy of water-speed data displayed by the chartplotter. 1 Select Settings > My Vessel > Calibrate Water Speed. 2 Follow the on-screen instructions. If the boat is not moving fast enough or the speed sensor is not registering a speed, a message appears. 3 Select OK, and safely increase the boat speed. 4 If the message appears again, stop the boat, and ensure the speed-sensor wheel is not stuck. 5 If the wheel turns freely, check the cable connections. 6 If you continue to get the message, contact Garmin product support. Communication with Wireless Devices NOTE: This will delete all settings information you have entered. Select Settings > System > System Information > Factory Settings > Reset. EN 2 Select Settings > My Vessel > Keel Offset. 3 Select or based on the location of the transducer. 4 Enter the distance measured in step 1. TI AL When your compatible chartplotter is connected to an AIS device or VHF radio, you can set up how other vessels are displayed on the chartplotter. Select Settings > Other Vessels. AIS: Enables and disables AIS signal reception. DSC: Enables and disables digital selective calling (DSC). Collision Alarm: Sets the collision alarm (Setting the Safe-Zone Collision Alarm). AIS-EPIRB Test: Enables test signals from Emergency Position Indicating Radio Beacons (EPRIB). AIS-MOB Test: Enables test signals from man overboard (MOB) devices. AIS-SART Test: Enables test transmissions from Search and Rescue Transponders (SART). Communication with Wireless Devices The chartplotters can create a wireless network to which you can connect wireless devices. Connecting wireless devices allows you to use Garmin apps, including BlueChart Mobile and Garmin Helm™. See www.garmin.com for more information. Setting Up the Wi‑Fi Wireless Network ® The chartplotters can create a Wi‑Fi network to which you can connect wireless devices. The first time you access the wireless network settings, you are prompted to set up the network. 1 Select Settings > Communications > Wi-Fi® Network > Wi-Fi® > On > OK. 2 If necessary, enter a name for this wireless network. 3 Enter a password. You will need this password to access the wireless network from a wireless device. The password is case-sensitive. Connecting a Wireless Device to the Chartplotter Before you can connect a wireless device to the chartplotter wireless network, you must configure the chartplotter wireless network (Setting Up the Wi‑Fi Wireless Network). You can connect multiple wireless devices to the chartplotter to share data. 1 From the wireless device, turn on the Wi‑Fi technology and search for wireless networks. 2 Select the name of your chartplotter wireless network (Setting Up the Wi‑Fi Wireless Network). 3 Enter the network password. ® ® 37 Changing the Wireless Channel Selecting a File Type for Third-Party Waypoints and Routes You can change the wireless channel if you have trouble finding or connecting to a device, or if you experience interference. 1 Select Settings > Communications > Wi-Fi® Network > Advanced > Channel. 2 Enter a new channel. You do not need to change the wireless channel of devices connected to this network. You can import and export waypoints and routes from third-party devices. 1 Select Info > User Data > Data Transfer > File Type. 2 Select GPX. To transfer data with Garmin devices again, select the ADM file type. Changing the Wi‑Fi Host Copying Data from a Memory Card Wireless Remote Control Pairing the Wireless Remote Control With the Chartplotter Turning On and Off the Remote Backlight Turning off the remote backlight can significantly increase the battery life. 1 On the chartplotter, select Settings > Communications > Wireless Devices > Wireless Remote > Backlight. Follow the on-screen instructions. FI Disconnecting the Remote from All Chartplotters 1 On the chartplotter, select Settings > Communications > Wireless Devices > Wireless Remote > Disconnect All. 2 Follow the on-screen instructions. Using the Garmin Helm Application with the Chartplotter Before you can control the chartplotter with the Garmin Helm application, you must download and install the application, and connect the chartplotter to a Wi‑Fi router. 1 Select Settings > Communications > Wireless Devices > Helm App. 2 Select an option. 3 Use the application to view or control the chartplotter. Chartplotter Data Management Copying Waypoints, Routes, and Tracks from HomePort to a Chartplotter Before you can copy data to the chartplotter, you must have the latest version of the HomePort software program loaded on your computer and a memory card installed in the chartplotter. Copy the data from HomePort to the prepared memory card. For more information, see the HomePort help file. 38 Insert a memory card into a card slot. Select Info > User Data > Data Transfer. If necessary, select the memory card to copy data to. Select an option: • To transfer data from the memory card to the chartplotter and combine it with existing user data, select Merge from Card. • To transfer data from the memory card to the chartplotter and overwrite existing user data, select Replace from Card. 5 Select the file name. Copying Waypoints, Routes, and Tracks to a Memory Card EN Before you can use the wireless remote control with a chartplotter, you must pair the remote with the chartplotter. You can connect a single remote to multiple plotters, and then press the pairing key to switch between the chartlotters. 1 Select Settings > Communications > Wireless Devices > Wireless Remote. 2 Select New Connection. 3 Follow the on-screen instructions. TI AL You can change which chartplotter is serving as the Wi‑Fi host. The can be helpful if you are having trouble with Wi‑Fi communications. Changing the Wi‑Fi host allows you to select a chartplotter that is physically closer to your mobile device. 1 Select Settings > Communications > Wi-Fi® Network > Advanced > Wi-Fi Host. 2 Follow the on-screen instructions. Insert a memory card into the card slot. Select Info > User Data > Data Transfer > Save to Card. If necessary, select the memory card to copy data to. Select an option: • To create a new file, select Add New File, and enter a name. • To add the information to an existing file, select the file from the list. Copying Waypoints, Routes, and Tracks to or from all Chartplotters on the Network You can transfer information for waypoints, routes, and tracks from one chartplotter connected to the Garmin Marine Network to every other chartplotter connected to the network. The transfer may take a long time, depending on the number of waypoints being transferred. 1 Select Info > User Data > Data Transfer > Network. 2 Select an option: • To transfer data from the chartplotter to the other chartplotters connected to the network, select Clone User Data. Existing data is overwritten on those chartplotters. • To transfer data between all the chartplotters connected to the network, select Merge User Data. Unique data is combined with existing data on every chartplotter. Copying Built-In Maps to a Memory Card You can copy maps from the chartplotter to a memory card for use with HomePort. 1 Insert a memory card into the card slot. 2 Select Info > User Data > Data Transfer. 3 Select Copy Built-In Map. Backing Up Data to a Computer Insert a memory card into the card slot. Select Info > User Data > Data Transfer > Save to Card. Select a file name from the list, or select Add New File. Select Save to Card. Chartplotter Data Management attached to a computer. 6 Open the Garmin\UserData folder on the memory card. 7 Copy the backup file on the card and paste it to any location on the computer. Restoring Backup Data to a Chartplotter 1 Insert a memory card into a card reader that is attached to the computer. 2 Copy a backup file from the computer to the memory card, into a folder named Garmin\UserData. 3 Insert a memory card into the card slot. 4 Select Info > User Data > Data Transfer > Replace from Card. Screenshots You can capture a screenshot of any screen shown on your chartplotter as a bitmap (.bmp) file. You can transfer the screenshot to your computer. Capturing Screenshots 1 Insert a memory card into the card slot. 2 Select Settings > Preferences > Screenshot Capture > On. 3 Go to a screen you want to capture. 4 Hold Home for at least six seconds. Copying Screenshots to a Computer 1 Remove the memory card from the chartplotter, and insert it into a card reader that is attached to a computer. 2 From Windows Explorer, open the Garmin\scrn folder on the memory card. 3 Copy a .bmp file from the card and paste it to any location on the computer. TI AL 5 Remove the memory card, and insert it into a card reader ® Saving System Information to a Memory Card Appendix Registering Your Device FI Help us better support you by completing our online registration today. • Go to http://my.garmin.com. • Keep the original sales receipt, or a photocopy, in a safe place. Digital Switching Your chartplotter can be used to monitor or control circuits when a compatible system is connected. For example, you can control the interior lights and navigation lights on the vessel. You can also monitor live well circuits. To access the digital switching controls, select Info > Circuit Control. For more information about purchasing and configuring a digital switching system, contact your Garmin dealer. Rotating the GRID Joystick For certain installation situations, you can rotate the orientation of the GRID joystick. 1 Select Settings > Communications > Marine Network. 2 Select the GRID device. Cleaning the Screen NOTICE Cleaners containing ammonia will harm the anti-reflective coating. The device is coated with a special anti-reflective coating which is very sensitive to skin oils, waxes, and abrasive cleaners. 1 Apply an eyeglass lens cleaner specified as safe for antireflective coatings to the cloth. 2 Gently wipe the screen with a soft, clean, lint-free cloth. Appendix Troubleshooting My device will not acquire GPS signals If the device is not acquiring satellite signals, there could be few causes. If the device has moved a large distance since the last time it has acquired satellites or has been turned off for longer than a few weeks or months, the device may not be able to acquire the satellites correctly. • Ensure the device is using the latest software. If not, update the device software (Updating the Device Software). • If the device is using an internal GPS antenna, make sure the device has a clear view of the sky so that the internal antenna can receive the GPS signal. If it is mounted inside of a cabin, it should be close to a window so it can receive the GPS signal. If the device is mounted inside a cabin and cannot be placed in a location where the device can acquire satellites, use an external GPS antenna. • If the device is using an external GPS antenna, make sure the antenna is connected to the chartplotter or the NMEA network. • If the device has more than one GPS antenna source, select a different source (Selecting the GPS Source). EN You can save system information to a memory card as a troubleshooting tool. A product support representative may ask you to use this information to retrieve data about the network. 1 Insert a memory card into the card slot. 2 Select Settings > System > System Information > Garmin Devices > Save to Card. 3 If necessary, select the memory card to save system information to. 4 Remove the memory card. My device will not turn on or keeps turning off Devices erratically turning off or not turning on could indicate an issue with the power supplied to the device. Check these items to attempt to troubleshoot the cause of the power issue. • Make sure the power source is generating power. You can check this several ways. For example, you can check whether other devices powered by the source are functioning. • Check the fuse in the power cable. The fuse should be located in a holder that is part of the red wire of the power cable. A 3 Amp fuse is used in this power cable. Check the fuse to make sure there is still a connection inside of the fuse. You can test the fuse using a multimeter. If the fuse is good, the multimeter reads 0 ohms. • Check to make sure the device is receiving is at least 10 volts, but 12 volts is recommended. To check the voltage, measure the female sockets 8 (power) and 2 (ground) of the power cable for DC voltage. If the voltage is less than 10 volts, the device will not turn on. • If the device is receiving enough power but does not turn on, contact Garmin product support at www.garmin.com/support. 39 You can manually enter a waypoint location to transfer and share data from one device to the next. If you have manually entered a waypoint using coordinates, and the location of the point does not appear where the point should be, the map datum and position format of the device may not match the map datum and position format originally used to mark the waypoint. Position format is the way in which the GPS receiver's position appears on the screen. Commonly displayed as latitude/ longitude in degrees and minutes, with options for degrees, minutes and second, degrees only, or one of several grid formats. Map datum is a math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum. 1 Find out which map datum and position format was used when the original waypoint was created. If the original waypoint was taken from a map, there should be a legend on the map that lists the map datum and position format used to create that map. Most often this is found near the map key. NMEA 0183 Information Sentence Description Transmit GPAPB APB: Heading or track controller (autopilot) sentence "B" Meteorological composite MWV Wind speed and angle VDM AIS VHF data-link message NMEA 2000 PGN Information Type PGN Transmit and receive 059392 ISO acknowledgment Description 059904 ISO request 060928 ISO address claim 126208 NMEA: Command, request, and acknowledge group function 126464 Transmit and receive PGN list group function 126996 Product information 129026 COG and SOG : Rapid update 129029 GNSS position data 129540 GNSS satellites in view 130306 Wind data 130312 Temperature Transmit 127250 Vessel heading 127258 Magnetic variance 128259 Speed: Water referenced 128267 Water depth 129025 Position: Rapid update 129283 Cross track error 129284 Navigation data 129285 Navigation route and waypoint info GPBWC BWC: Bearing and distance to waypoint GPGGA GGA: Global positioning system fix data GPGLL GLL: Geographic position (latitude and longitude) 127488 Engine parameters: Rapid update GPGSA GSA: GNSS DOP and active satellites 127493 Transmission parameters: Dynamic GPGSV GSV: GNSS satellites in view 127505 Fluid level GPRMB RMB: Recommended minimum navigation information 128259 Speed: water referenced GPRMC RMC: Recommended minimum specific GNSS data 129025 Position: rapid update GPRTE RTE: Routes GPVTG VTG: Course over ground and ground speed GPWPL WPL: Waypoint location GPXTE XTE: Cross track error PGRME E: Estimated error PGRMM M: Map datum PGRMZ Z: Altitude SDDBT DBT: Depth below transducer SDDPT DPT: Depth FI BOD: Bearing (origin to destination) MTW: Water temperature SDVHW VHW: Water speed and heading SDMTW Receive DPT DBT 40 MDA GPBOD Type Sentence Description EN 2 On the chartplotter, select Settings > Preferences > Units. 3 Select the correct map datum and position format settings. 4 Create the waypoint again. Type TI AL My device is not creating waypoints in the correct location Depth Depth below transducer MTW Water temperature VHW Water speed and heading WPL Waypoint location DSC Digital selective calling information DSE Expanded digital selective calling HDG Heading, deviation, and variation HDM Heading, magnetic MWD Wind direction and speed Receive 126992 System time 127250 Vessel heading 127489 Engine parameters: Dynamic 128267 Water depth 129038 AIS class A position report 129039 AIS class B position report 129040 AIS class B extended position report 129539 GNSS DOPs 129794 AIS class A static and voyage related data 129809 AIS class B "CS" static data report, part 129810 AIS class B "CS" static data report, part 130310 Environmental parameters 130311 Environmental parameters 130313 Humidity 130314 Actual pressure Software License Agreement BY USING THE DEVICE, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin Ltd. and its subsidiaries (“Garmin”) grant you a limited license to use the software embedded in this device (the “Software”) in binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property Appendix TI AL FI EN rights in and to the Software remain in Garmin and/or its thirdparty providers. You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and international copyright treaties. You further acknowledge that the structure, organization, and code of the Software, for which source code is not provided, are valuable trade secrets of Garmin and/or its third-party providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America or the export control laws of any other applicable country. Appendix 41 Index current stations 27, 28 indicators 4 camera configuration 33 controlling 33 home position 33 pausing 33 standby 33 celestial information 27, 28 charts 2–4, 6, 7 appearance 7 built-in 3 details 3 heading, line 7 measuring distance 3 navigation 4, 5 selecting 3 symbols 3 circuits 39 clock 36 alarm 36 collision alarm 6, 37 color mode 2 combinations, customizing 2, 34 compass, rose 7 courses 8 42 jibing. See tacking and gybing joystick 39 EN EBL 20 adjusting 21 measuring 21 showing 21 engine gauges 26 configuring 26 status alarms 26 EPIRB 6 event log 34 hazard colors 7 heading 24 adjusting 24 heading hold 14 holding 23 Shadow Drive 24 helm application 38 help. See product support home screen 1 customizing 2 TI AL factory settings 37 stations 2 favorites 2 Fish Eye 3D sonar cone 7 suspended targets 7 tracks 7 fishing chart 3, 32 setup 7 fuel alarm 26, 36 fuel capacity 26, 36 fuel gauges 26 status alarm 26, 36 synchronizing with actual fuel 27 fuel onboard 36 backlight 2, 38 buoy reports 32 data backup 38, 39 copying 38 data management 38 dealer 8 deleting, all user data 12 depth log 27 destinations navigation chart 8 selecting 8 device cleaning 39 registration 39 digital selective calling 24, 25 channels 26 contacts 25 individual routine call 26 turning on 25, 37 digital switching 39 distress call 25 distress signal device 6 DownVü 15 DSC. See digital selective calling FI aerial photos 5 AIS 5–7 distress signal device 6 radar 20 SART 6 targeting 5, 6 threats 6, 20 turning on 37 alarms 36 anchor drag 36 arrival 36 collision 6, 37 deep water 18 engine 26 gauges 26 navigation 36 off course 36 shallow water 18 sonar 18 water temperature 18 weather 36 anchor drag alarm 36 animated currents, tides 4 antenna, GPS 1 arrival alarm 36 Auto Guidance 8, 10, 11, 35 line 11, 35 paths 10, 11 shoreline distance 11, 35 autopilot 23 adjusting the heading 24 circles pattern 24 cloverleaf pattern 24 engaging 23 orbit pattern 24 pattern steering 24 power saver 23 reducing rudder activity 23 search pattern 24 Shadow Drive 23 steering increment 23 steering patterns 24 u-turn pattern 24 Williamson turn pattern 24 zigzag pattern 24 gybing. See tacking and gybing Garmin Marine Network 12, 36 Garmin product support, contact information 1 gauges 26 engine 26 fuel 26, 27 limits 26 status alarms 26 trip 27 wind 27 Go To 9 GPS 39 signals 1 source 1 GPS accuracy 36 graphs air temperature 27 atmospheric pressure 27 configuring 27 depth 27 water temperature 27 wind angle 27 wind speed 27 GRID 39 GRID pairing 34 keel offset 13, 36 keyboard 34 lane width 7 language 34 man overboard 9, 24, 25 manual viewer 1 marine services 8 mark location 8 MARPA 5 navigation chart 7 tagged object 20 targeting 20 threats 6, 20 measuring distance, charts 3 media player 28 alphabetical search 28 Android device 29 device name 30 FUSION-Link 28, 29 iPod 28 MTP 29 muting 29 preset 28, 33 radio 28, 29 repeating 28 shuffling 28 SiriusXM Satellite Radio 29 source 28 tuner region 29 tuning mode 29 VHF 29 Windows phone 29 zones 29 memory card 38, 39 detailed maps 38 MOB, device 6 music player 28–30. See media player navaids 4 navigation alarms 36 navigation chart 3, 5, 8, 32 aerial photos 7 marine service points 8 MARPA 7 radar overlay 21 setup 7 vessel trails 7, 25 networking. See Marine Network NMEA 0183 24, 36 NMEA 2000 24, 36 off course alarm 36 offset, front of boat 23 other vessels AIS 7 trails 7 Index Perspective 3D 32 photos, aerial 5 position, tracking 25 position report 25 power key 34 powerboat 2, 13, 37 preferred data source 23 premium charts 4, 5, 7 aerial photos 5 Fish Eye 3D 7 tide and current indicators 4 product registration 39 product support 1 contact information 1 FI radar 19–21 AIS 20 bird mode 21 clutter 22 color scheme 23 custom park position 21 echo trails 22 field of view 23 front-of-boat offset 23 gain 21, 22 MARPA 6 optimizing display 22 overlay screen 21 range 19 range rings 23 sentry mode 19 source 23 timed transmit 19 transmitting 19 waypoints 19, 23 zoom scale 19 radar overlay 21 radio, SiriusXM 29, 30 range rings 7 registering the device 39 remote control 38 disconnecting 38 resetting settings 30 station layouts 2 Route To 8 routes copying 38 creating 9, 10 deleting 10 editing 10 navigating 10 navigating parallel to 10 synchronizing 12 viewing list of 10 waypoints 38 safe depth 35 safe height 35 safe-zone collision alarm 6, 37 sailboat 2, 13, 37 sailing 7, 13 race timer 13 starting line 13 sailing gauges 27 sailingstarting line 13 SART 6 satellite imagery 5 satellite signals, acquiring 1 screen, brightness 2 screenshots 39 capturing 39 sentry mode 19 guard zone 20 timed transmit 19, 20 settings 34–36 radar display 22 Index EN system information 34 Shadow Drive, enabling 23 shoreline distance 11, 35 SideVü 15 SiriusXM 30 Satellite Radio 29 SiriusXM Satellite Radio 29, 30 software updates 1 updating 1 software license agreement 40 sonar 14, 15, 18 a-scope 17, 18 alarms 18 appearance 18 bottom lock 16 color gain 16 color rejection 18 cone 7 depth 16 depth scale 16 DownVü 15 frequencies 17 gain 16 interference 17 noise 16 recording 18, 19 scroll speed 17 sharing 15, 16 SideVü 15 source 15, 16 surface noise 17 suspended targets 18 views 14, 15 waypoint 15 whiteline 18 zoom 16 SOS 9, 25 stations 1 changing the station 34 customizing the home screen of 2 ordering the displays 34 restoring the layout 2, 34 suspended targets 7 symbols 5 synchronizing, user data 12 system information 34, 39 tacking and gybing 14 heading hold 14 wind hold 14 targeting 20 temperature log 27 tide stations 4, 27, 28 indicators 4 tracks 12 clearing 12 copying 38 deleting 12 editing 12 list 12 navigating 12 recording 12 saving 12 saving as route 12 showing 7, 12 transducer 14, 17, 18 trip gauges 27 troubleshooting 39, 40 vessel trails 7, 25 VHF radio 24 calling an AIS target 26 distress calls 25 DSC channel 26 individual routine call 26 video 32–34 configuring 33, 34 source 33, 34 viewing 33 voltage 36 Volvo Penta dealer 8 VRM 20 adjusting 21 measuring 21 showing 21 TI AL warning manager 28 messages 28 water speed 37 temperature log 27 temperature offset 37 waypoints 8, 40 copying 38 creating 3, 8, 32 deleting 9 editing 9 man overboard 9 navigating to 9 radar 19 showing 7 sonar 15 synchronizing 12 tracked vessel 25 viewing list of 9 weather 32 weather 7, 30, 31 alarms 36 broadcasts 30 charts 30, 32 fishing 31, 32 fishing chart 32 forecast 30–32 navigation chart 32 overlay 32 precipitation 30 sea conditions 31 subscription 30, 32 surface pressure 31 visibility 32 water temperature 31, 32 wave information 31 winds 31 Wi‑Fitechnology 37 wind angle graph 27 wind gauges 27 wind hold 14 adjusting 14 wind speed graph 27 wireless devices 37, 38 connecting a wireless device 37, 38 network configuration 37, 38 zoom chart 3 radar 19 sonar 16 unit ID 34 units of measure 35 updates, software 1 user data deleting 12 synchronizing 12 43 0800 770 4960 1-866-429-9296 +385 1 5508 272 +385 1 5508 271 +420 221 985466 +420 221 985465 + 45 4810 5050 + 358 9 6937 9758 + 331 55 69 33 99 + 39 02 36 699699 (+52) 001-855-792-7671 0800 0233937 +47 815 69 555 00800 4412 454 +44 2380 662 915 (+35) 1214 447 460 +386 4 27 92 500 0861 GARMIN (427 646) +27 (0)11 251 9999 +34 93 275 44 97 + 46 7744 52020 +886 2 2642-9199 ext 2 +49 (0)180 6 427646 20 ct./Anruf. a. d. deutschen Festnetz, Mobilfunk max. 60 ct./Anruf 913-397-8200 1-800-800-1020 FI 0808 238 0000 +44 (0) 870 8501242 EN + 32 2 672 52 54 +43 (0) 820 220230 TI AL www.garmin.com/support © 2014 Garmin Ltd. or its subsidiaries
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Extract Create Date : 2014:12:22 10:34:52-06:00 Creator : AH Formatter V5.3 MR3 (5,3,2011,1116) for Windows (x64) Modify Date : 2015:01:15 08:51:54-06:00 Type : Info Has XFA : No Language : Tagged PDF : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : AH Formatter V5.3 MR3 (5,3,2011,1116) for Windows (x64) Metadata Date : 2015:01:15 08:51:54-06:00 Producer : Antenna House PDF Output Library 2.6.0 (Windows (x64)) Trapped : False Format : application/pdf Document ID : uuid:afcb6704-e7c3-4afa-8b69-c744b7b97c9b Instance ID : uuid:ff5e21dd-9123-4d3b-8614-cc37db88fd7b Page Layout : SinglePage Page Mode : UseOutlines Page Count : 50EXIF Metadata provided by EXIF.tools