Garmin 296 M Ghp 10 Marine Autopilot System Manual Installation Instructions

2014-07-05

: Garmin 296-M-Ghp-10-Marine-Autopilot-System-Manual-Installation-Instructions 296-m-ghp-10-marine-autopilot-system-manual-installation-instructions garmin pdf

Open the PDF directly: View PDF .
Page Count: 26

Download
Open PDF In Browser	View PDF

Important Safety Information

GHP™ 10 Installation Instructions
To obtain the best possible performance and to avoid damage to your
boat, install the Garmin® GHP 10 marine autopilot system according
to the following instructions. Professional installation of the autopilot
system is highly recommended.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation, contact
Garmin Product Support.
NOTE: There is an installation checklist on the last page of these
instructions. Remove the last page and refer to the checklist as you
proceed through the GHP 10 installation.

‹ Warnings
You are responsible for the safe and prudent operation of your
vessel. The GHP 10 is a tool that will enhance your capability to operate
your boat. It does not relieve you from the responsibility of safely
operating your boat. Avoid navigational hazards and never leave the
helm unattended.
Always be prepared to promptly regain manual control of your boat.
Learn to operate the GHP 10 on calm and hazard-free open water.
Use caution when operating the GHP 10 near hazards in the water, such
as docks, pilings, and other boats.
See the Important Safety and Product Information guide in the product
box for product warnings and other important information.

Registering Your Device

‹ caution
Equipment to be connected to this product should have a fire enclosure
or be provided with a fire enclosure.

• Go to http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to each
component of your GHP 10 system in the spaces provided on page 3.
The serial numbers are located on a sticker on each component.

Always wear safety goggles, ear protection, and a dust mask when
drilling, cutting, or sanding.

Help us better support you by completing our online registration today.

Notice
When drilling or cutting, always check the opposite side of the surface.
Be aware of fuel tanks, electrical cables, and hydraulic hoses.

Contacting Garmin

Contact Garmin Product Support if you have any questions while using
your GHP 10.
In the USA, go to www.garmin.com/support, or contact Garmin USA
by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to www.garmin.com/support and click Contact Support
for in-country support information, or contact Garmin (Europe) Ltd. by
phone at +44 (0) 870.8501241.

GHP 10 Installation Instructions

Table of Contents
GHP™ 10 Installation Instructions....................................1

Registering Your Device............................................................... 1
Contacting Garmin....................................................................... 1
Important Safety Information........................................................ 1

GHP 10 Package Contents and Tools Needed................3
Main Components........................................................................ 3

CCU....................................................................................................3
ECU....................................................................................................3
Hydraulic Pump and Motor.................................................................3
Shadow Drive.....................................................................................3
GHC 10...............................................................................................3

Cables and Connectors................................................................ 4

CCU/ECU Interconnect Cable............................................................4
Alarm..................................................................................................4
ECU Power Cable...............................................................................4
GHC 10 NMEA 0183 Data Cable........................................................4
NMEA 2000 Cables and Connectors..................................................4
External Tachometer Filter..................................................................4

Tools Needed............................................................................... 4

Installation Preparation....................................................5
Mounting and Connection Considerations................................... 5

Shadow Drive Mounting Considerations.............................................5
ECU Mounting Considerations...........................................................5
ECU Connection Considerations........................................................5
Hydraulic Considerations for Avoiding ECU Drive Circuit Overload...5
CCU Mounting Considerations...........................................................5
CCU Connection Considerations........................................................5
Alarm Mounting Considerations . .......................................................5
Alarm Connection Considerations......................................................5
NMEA 2000 Connection Considerations............................................6
GHC 10 Mounting Considerations......................................................6
GHC 10 Connection Considerations...................................................6
Speed Source Connection Considerations.........................................6

General Connections Diagram..................................................... 7
Single-helm Layout Guidelines..................................................... 8
Dual-helm Layout Guidelines....................................................... 9

Building a Basic NMEA 2000 Network for the GHC 10 and the
CCU............................................................................................13

Connecting Optional Devices to the GHP 10 Autopilot
System..................................................................................... 14

NMEA 0183 Connection Considerations..........................................14
Connecting an Optional NMEA 0183-compatible Device to the
GHC 10.......................................................................................14

Configuring the GHP 10..................................................14

About the Dockside Wizard........................................................ 14
Starting the Dockside Wizard..................................................... 14
Performing the Dockside Wizard................................................ 14
Calibrating Lock-to-Lock Turns.........................................................14
Calibrating Helm Displacement........................................................14
Testing the Steering Direction...........................................................14
Selecting the Speed Source.............................................................15
Verifying the Tachometer..................................................................15
Reviewing the Results of the Dockside Wizard................................15

About the Sea Trial Wizard......................................................... 15
Important Sea Trial Wizard Considerations................................ 15
Starting the Sea Trial Wizard...................................................... 15
Performing the Sea Trial Wizard................................................ 15
Configuring the Planing RPM...........................................................15
Configuring the Planing Speed.........................................................15
Configuring the High RPM Limit.......................................................15
Configuring the Maximum Speed.....................................................15
Calibrating the Compass..................................................................16
Performing the Autotune Procedure.................................................16
Setting North.....................................................................................16
Setting the Fine Heading Adjustment...............................................16

Evaluating the Results of the Autopilot Configuration................ 16

Testing and Adjusting the Autopilot Configuration.............................16
Adjusting the Acceleration Limiter Settings.......................................16
Adjusting the Autopilot Gain Settings................................................17
Reducing the Risk of ECU Drive Circuit Overload............................17
Adjusting the Rudder Rate Limiter....................................................17

Advanced Configuration Procedure........................................... 17
Enabling the Advanced Configuration Procedure.............................17

Advanced Configuration Settings............................................... 17

Installation Procedures...................................................10

Manually Running the Automated Configuration Procedures...........17
Manually Running the Dockside and Sea Trial Wizards...................17
Manually Defining Individual Configuration Settings.........................17

Connecting the Shadow Drive to the Hydraulics..............................10
Connecting the Shadow Drive..........................................................10

Appendix..........................................................................18

Shadow Drive Installation........................................................... 10

ECU Installation.......................................................................... 10
ECU on a 24 Vdc System.................................................................10
Mounting the ECU............................................................................10
Connecting the ECU to Power..........................................................10

CCU Installation......................................................................... 10

Installing the CCU Mounting Bracket................................................10
Securing the CCU in the CCU Bracket............................................. 11
Connecting the CCU......................................................................... 11
Connecting the GHP to the Tachometer........................................... 11

Alarm Installation.........................................................................11

NMEA 0183 Connection Diagrams............................................. 18
Specifications............................................................................. 18
NMEA 2000 PGN Information.................................................... 19

CCU..................................................................................................19
GHC 10.............................................................................................19

NMEA 0183 Information............................................................. 20
GHP 10 Configuration Settings.................................................. 20
Error and Warning Messages..................................................... 22
CCU Mounting Template............................................................ 23
GHP 10 Installation Checklist..................................................... 25

Mounting the Alarm........................................................................... 11
Connecting the Alarm....................................................................... 11

GHC 10 Installation.....................................................................11
Mounting the GHC 10....................................................................... 11
Connecting the GHC 10....................................................................12
Multiple GHC 10 Considerations......................................................12

Connecting the Devices to a NMEA 2000 Network.................... 12
Connecting the GHC 10 to an Existing NMEA 2000 Network...........12
Connecting the CCU to an Existing NMEA 2000 Network................13

GHP 10 Installation Instructions

GHP 10 Package Contents and Tools
Needed
The GHP 10 autopilot system consists of multiple components.
Familiarize yourself with all of the components before beginning
installation. You must know how the components operate together in
order to correctly plan the installation on your boat.
As you familiarize yourself with the GHP 10 components, confirm
that your package includes the items listed below. All the components,
except the hydraulic pump, are included in the GHP 10 core box. If any
parts are missing, contact your Garmin dealer immediately.

Hydraulic Pump and Motor
The hydraulic pump (and motor) steers your boat by interacting with
the hydraulic steering system, based on commands you enter using the
GHC 10. The pump is not included in the GHP 10 core package box
because the type of pump you use with your GHP 10 is determined
by the size and type of steering system on your boat. The pump is
in a separate box. For information on installing the pump, see the
installation instructions included in the pump box.
Serial Number

Shadow Drive

Record the serial number of each component in the space provided.

Main Components

The GHP 10 autopilot system consists of five main components: the
Electronic Control Unit (ECU), the Course Computer Unit (CCU), a
hydraulic pump, the Shadow Drive™, and the GHC™ 10 user control
interface.
CCU

The Shadow Drive is a sensor you install in the hydraulic steering
lines of your boat. While the GHP 10 is engaged, the Shadow Drive
temporarily disengages the autopilot when you manually take control of
the helm. When you establish a new straight line heading, the Shadow
Drive automatically reengages the autopilot.
Serial Number

GHC 10
The CCU acts as the brain of the GHP 10. The CCU contains the
sensory equipment used to determine heading. The CCU connects to the
ECU and to the GHC 10 with a single cable. The CCU also connects
to a NMEA 2000® network to communicate with the GHC 10, and to
optional NMEA 2000-compatible GPS devices (page 12).
Serial Number

ECU

The GHC 10 is the primary interface used to operate the GHP 10
autopilot system. Using the GHC 10, you engage and steer the GHP 10.
You also set up and customize the GHP 10 using the GHC 10.
The GHC 10 connects to a NMEA 2000 network to communicate
with the CCU. The GHC 10 also connects with optional NMEA
2000-compatible devices such as a GPS device, to use advanced
features of the GHP 10. If NMEA 2000-compatible devices are
not available, you can connect the GHC 10 to optional NMEA
0183-compatible devices instead.
Serial Number

The ECU connects to the CCU and to the drive unit. The ECU controls
the drive unit based on information from the CCU. The ECU powers
both the CCU and the drive unit.
Serial Number

GHP 10 Installation Instructions

Cables and Connectors

The GHP 10 autopilot system includes multiple cables. These cables
connect the components to power, to each other, to an alarm, and to
optional devices.
CCU/ECU Interconnect Cable
This cable connects the CCU to the ECU. A portion of this cable
contains color-coded wires with bare ends. These wires connect the
CCU to the alarm and to the yellow wire from the GHC 10.

NMEA 2000 Cables and Connectors
The NMEA 2000 cables connect the CCU and the GHC 10 to the
NMEA 2000 network. Either connect the CCU and the GHC 10 to an
existing NMEA 2000 network using the included T-connectors and drop
cables, or use all of the included NMEA 2000 cables and connectors to
build a NMEA 2000 network on your boat if needed (page 12).

➊
➋

CCU/ECU Interconnect Extension Cables

➌

When installing the GHP 10 system, you may need to mount the
CCU farther than 16 ft. (5 m) from the ECU. Garmin offers optional
replacement or extension cables for purchase if this is necessary.
Type
Replacement
Replacement
Extension
Extension
Extension

Length
32 ft. (10 m)
66 ft. (20 m)
16 ft. (5 m)
50 ft (15 m)
82 ft. (25 m)

Contact your local Garmin dealer or Garmin Product Support for
ordering information.
Alarm
The alarm provides audible alerts from the GHP 10 (page 11).

ECU Power Cable
This cable powers the ECU (page 10).

➊
➋
➌
➍
➎

➍

➎

NMEA 2000 drop cable, 6 ft. (2 m) (×2)
NMEA 2000 power cable
NMEA 2000 T-connector (×3)
NMEA 2000 terminator, male
NMEA 2000 terminator, female

NMEA 2000 Extension Cables

NMEA 2000 extension cables are available if needed. Contact
your local Garmin dealer or Garmin Product Support for ordering
information.
External Tachometer Filter
If your tachometer source is a direct alternator connection or other
signal larger than 12 Vdc, or if you sporadically receive tachometer
errors, install an external tachometer filter (Garmin part number: 01011399-00), not included. Contact your local Garmin dealer or Garmin
product support for ordering information.

Tools Needed

GHC 10 NMEA 0183 Data Cable
Included in the GHC 10 box, this cable connects the GHC 10 to the
yellow wire of the CCU, and to the same ground as the ECU (page
12). This cable can also be used to connect the GHC 10 to optional
NMEA 0183-compatible devices (page 14).

•
•
•
•
•
•
•

Safety glasses
Drill and drill bits
3 1/2 in. (90 mm) hole saw
Wire cutters/strippers
Phillips and flat screwdrivers
Cable ties
Waterproof wire connectors (wire nuts) or heat-shrink tubing and a
heat gun
• Marine sealant
• Portable or handheld compass (to test for magnetic interference
when determining the best location to install the CCU)
• Anti-seize lubricant (optional)
Note: Mounting screws are provided for the GHC 10, for the
CCU, for the ECU, and for the pump. If the provided screws are not
appropriate for the mounting surface, you must provide the correct
types of screws.

GHP 10 Installation Instructions

Installation Preparation
Before installing the GHP 10 autopilot system, you must plan where all
the components will be located on your boat. Temporarily place all the
components where you intend to install them. Read these considerations
and consult the diagrams on pages 7–9 before you begin planning your
installation.
NOTE: There is an installation checklist on the last page of these
instructions. Remove the last page and refer to the checklist as you
proceed through the GHP 10 installation.

Mounting and Connection Considerations

The GHP 10 components connect to each other and to power using the
included cables. Ensure that the correct cables reach each component
and that each component is in an acceptable location before mounting
or connecting any components.
Shadow Drive Mounting Considerations
• Mount the Shadow Drive horizontally and as level as possible, using
cable ties to firmly secure it in place.
• Mount the Shadow Drive at least 12 in. (0.3 m) away from
magnetic material such as speakers and electric motors,
including the autopilot pump.
• Install the Shadow Drive closer to the helm than to the pump.
• Install the Shadow Drive lower than the helm, but higher than the
pump.
• Avoid making loops in the hydraulic lines.
• Do not install the Shadow Drive directly to the fittings at the back of
the helm. Install a length of hose between the fitting at the helm and
the Shadow Drive.
• Do not install the Shadow Drive directly to a hydraulic T-connector
in the hydraulic line. Install a length of hose between a
T-connector and the Shadow Drive.
• In a single-helm installation, do not install a T-connector
between the helm and the Shadow Drive.
• In a dual-helm installation, install the Shadow Drive between
the pump and the lower helm, closer to the helm than to the
pump.
• Install the Shadow Drive in either the starboard steering line or the
port steering line. Do not install the Shadow Drive in the return
line.
• Do not use Teflon tape on any hydraulic fitting. Use an appropriate
thread sealant such as Loctite Pro Lock Tight multipurpose
anaerobic gel, part number 51604, or equivalent, on all pipe threads
in the hydraulic system.
ECU Mounting Considerations
• The ECU can be mounted on a flat surface facing any direction.
• Mounting screws are included with the ECU, but you may need to
provide different screws if the supplied screws are not suitable for
the mounting surface.
• The ECU must be located within 19 in. (0.5 m) of the drive unit.
• The ECU must not be mounted in a location where it will be
submerged or exposed to wash-down.

ECU Connection Considerations
• The ECU power cable connects to the boat battery, and it can be
extended if needed (page 10).
• ECU units with a serial number prior to 19E002748 are only
compatible with 12 Vdc systems.
ECU units with a serial number of 19E002748 or later are
compatible with both 12 Vdc and 24 Vdc systems.
• The cables connecting the pump to the ECU cannot be extended.
Hydraulic Considerations for Avoiding ECU Drive Circuit
Overload
• Ensure the appropriate pump has been correctly installed on your
boat.
NOTE: If you have questions about the appropriate pump for your boat,
contact your local Garmin dealer or Garmin Product Support for more
information.
• If possible, use larger inside diameter hydraulic hoses on your
steering system.
• Mount the pump closer to the cylinder to limit the length of the hose
runs.
• Eliminate unneeded hydraulic fittings in the hydraulic fittings.
CCU Mounting Considerations
• The CCU must be mounted in the forward half of the boat, no
higher than 10 ft. (3 m) above the waterline.
• The CCU must not be mounted in a location where it will be
submerged or exposed to wash-down.
• The CCU must not be mounted near magnetic material,
magnets (speakers and electric motors), or high-current wires.
• The CCU must be mounted at least 24 in. (0.6 m) away from
movable or changing magnetic disturbances such as anchors, anchor
chain, wiper motors, and tool boxes.
• A handheld compass should be used to test for magnetic interference
in the area where the CCU is to be mounted.
If the handheld compass does not point north when you hold it in
the location where you intend to mount the CCU, there is magnetic
interference. Choose another location, and test again.
• The CCU can be mounted below the waterline if it is not in a
location where it will be submerged or exposed to wash-down.
• The CCU bracket must be mounted on a vertical surface or under a
horizontal surface, so that the connected wires hang straight down.
• Mounting screws are included with the CCU, but you may need to
provide different screws if the supplied screws are not suitable for
the mounting surface.
CCU Connection Considerations
• The CCU/ECU interconnect cable connects the CCU to the ECU
and is 16 ft. (5 m) long.
◦◦ If the CCU cannot be mounted within 16 ft. (5 m) of the ECU,
replacement and extension cables are available (page 4).
◦◦ The CCU/ECU interconnect cable must not be cut.
• The CCU/ECU interconnect cable connects the CCU to the GHC 10
with a single yellow signal wire (page 11). The autopilot system
does not power on if this connection is not made.
Alarm Mounting Considerations
• The alarm should be mounted near the helm station.
• The alarm can be mounted under the dashboard.
Alarm Connection Considerations
• If needed, the alarm wires can be extended with 28 AWG (.08 mm2)
wire.

GHP 10 Installation Instructions

NMEA 2000 Connection Considerations
• The CCU and the GHC 10 connect to the NMEA 2000 network.
If your boat does not have a NMEA 2000 network, one can be built
using the included NMEA 2000 cables and connectors
(page 13).
• To use advanced features of the GHP 10, optional NMEA
2000-compatible devices, such as a GPS device, can be connected to
the NMEA 2000 network.
GHC 10 Mounting Considerations
• The mounting location should provide optimal viewing as you
operate your vessel.
• The mounting location should allow easy access to the keys on the
GHC 10.
• The mounting surface must be strong enough to support the weight
of the GHC 10 and protect it from excessive vibration or shock.
• The area behind the surface must allow room for the routing and
connection of the cables.
There should be at least a 3-inch (8 cm) clearance behind the case of
the GHC 10.
• The location must be at least 91/2 in. (0.24 m) from a magnetic
compass, to avoid interference.
• The location must be in an area that is not exposed to extreme
temperature conditions (page 19).
GHC 10 Connection Considerations
• You must connect the GHC 10 to the NMEA 2000 network.
• For the autopilot to function, you must correctly connect two wires
from the GHC 10 data cable:
◦◦ The yellow wire from the GHC 10 data cable must be connected
to the yellow wire of the CCU/ECU interconnect cable.
◦◦ The black wire from the GHC 10 data cable must be connected
to the same ground as the ECU.
• Optional NMEA 0183-compatible devices, such as a GPS device,
can be connected to the GHC 10 data cable (page 14).

Speed Source Connection Considerations
For optimal performance in all conditions, Garmin recommends
connecting to a NMEA 2000 or analog tachometer speed source. Each
speed source in the table is listed in order of best to least in terms of
autopilot performance.
Speed
Source

Appropriate Connection

NMEA 2000 • If your engine supports NMEA 2000 engine data,
Engine
and is connected to the same NMEA 2000 network
Data
as the GHC 10 and the CCU, no other tachometry
connection is necessary. For more information on
the NMEA 2000 network, see page 12.
Note: Mercury and Volvo offer add-on NMEA
2000 gateways to share Mercury and Volvo engine
information over the NMEA 2000 network. If you
have a Mercury or Volvo engine, these adapters
provide the easiest installation and the most reliable
engine data transfer. See your marine dealer for
more details.
Tachometer • If your engine does not support NMEA 2000 engine
data, you can connect the GHP 10 autopilot system
to the tachometer of your boat using the bare-wire
portion of the CCU/ECU interconnect cable. In most
cases, this connection can be made behind the
dashboard at the tachometer display.
• Refer to the owner’s manual or shop manual
for your engine to identify the color codes and
location of the tachometer connections on your
boat.
• For a list of common engine tachometry
connections, visit www.garmin.com/ghp10/ and click
the manuals quick link.
Note: If your boat uses an electrical system that
provides more than 12 Vdc, or if you sporadically
receive tachometer errors, install an external
tachometer filter (010-11399-00). Contact your local
Garmin dealer or Garmin product support for more
information.
GPS

• GPS data can be used when tachometer data is
unavailable or unusable.
Note: GPS speed source data is supported only
with GHC 10 software version 3.00 or higher when
used with GHP 10 software version 3.30 or higher.
• When connected to the GHC 10, GPS data can be
sent to the GHP 10 by connecting the device to a
NMEA 2000 or NMEA 0183 network.

None

• Although it is not recommended; some boats, such
as displacement hulls, can be configured to use no
speed source.
• No connections are necessary when the selected
speed source is ‘None’.

GHP 10 Installation Instructions

General Connections Diagram

Refer to this diagram for component-interconnection reference only. Follow the detailed installation instructions for each component.

➊

➋

➍
➌

➎

}

➏

➐
POWER
CCU

DRIVE
FEEDBACK

➑

➒
GHP 10 General Connection Outline

Item Description
GHC 10
➊
➋

➌

➍

➎
➏
➐
➑

➒

Important Considerations

GHC 10 data cable

In order for the autopilot to turn on, the yellow wire from this cable must be connected to the yellow wire from
the CCU/ECU interconnect cable, and the black wire from this cable must be connected to the same ground
as the ECU (page 12).
NMEA 2000 power cable
This cable should be installed only if you are building a NMEA 2000 network. Do not install this cable if there is
an existing NMEA 2000 network on your boat (page 13).
The NMEA 2000 power cable must be connected to a 9–16 Vdc power source.
NMEA 2000 network
The GHC 10 and the CCU must be connected to the NMEA 2000 network using the included T-connectors
(page 12).
If there is not an existing NMEA 2000 network on your boat, you can build one using the supplied cables and
connectors (page 13).
CCU
Mount the CCU with the cables pointing straight down (page 10).
Boat Tachometer
For tachometer connection, see page 11.
ECU
The ECU can be mounted in any orientation.
ECU power cable
The ECU can be connected to a 12–24 Vdc power source. To extend this cable, use the correct wire gauge
(page 10).
The black wire from the GHC 10 data cable must be connect to the same ground as this cable (page 12).
CCU/ECU interconnect cable In order for the autopilot to turn on, the yellow wire from this cable must be connected to the yellow wire from
the GHC 10 data cable.
To extend this cable to reach the ECU, purchase the necessary extensions (page 4).
The red and blue wires from this cable must be connected to the alarm (page 11).

GHP 10 Installation Instructions

Single-helm Layout Guidelines

➊

➋

➌
➎

➍
NMEA 2000 network

NOTE: This diagram is for planning purposes only. Specific connection diagrams are included in the detailed installation instructions for each
component. Hydraulic connections are not shown in this diagram.
Item Description
GHC 10
➊

➋
➌

➍
➎

Important Considerations
In order for the autopilot to turn on, the yellow wire from the GHC 10 data cable must be connected to the yellow wire
from the CCU/ECU interconnect cable, and the black wire from the GHC 10 data cable must be connected to the
same ground as the ECU (page 12).
CCU
The CCU must be installed in the front half of the boat, no higher than 10 ft. (3 m) above the waterline.
NMEA 2000 network The GHC 10 and the CCU must be connected to the NMEA 2000 network using the included T-connectors (page 12).
If there is not an existing NMEA 2000 network on your boat, you can build one using the supplied cables and
connectors (page 13).
12-24 Vdc battery
The ECU can be connected to a 12–24 Vdc power source.
The NMEA 2000 power cable must be connected to a 9–16 Vdc power source.
ECU
The ECU can be connected to either a 12 or a 24 Vdc battery.

GHP 10 Installation Instructions

Dual-helm Layout Guidelines

➊

➊
➋

➍

➌

➎

➋
➌

➍
➎

Important Considerations
In order for the autopilot to turn on, the yellow wire from the GHC 10 data cable must be connected to the yellow wire
from the CCU/ECU interconnect cable, and the black wire from the GHC 10 data cable must be connected to the
same ground as the ECU (page 12).
CCU
The CCU must be installed in the front half of the boat, no higher than 10 ft. (3 m) above the waterline.
NMEA 2000 network The GHC 10 and the CCU must be connected to the NMEA 2000 network using the included T-connectors (page 12).
If there is not an existing NMEA 2000 network on your boat, you can build one using the supplied cables and
connectors (page 13).
ECU
The ECU can either be connected to a 12 or a 24 Vdc battery.
12-24 Vdc battery
The ECU can be connected to a 12–24 Vdc power source.
The NMEA 2000 power cable must be connected to a 9–16 Vdc power source.

GHP 10 Installation Instructions

Installation Procedures

Connecting the ECU to Power

After you have completely planned the GHP 10 installation on your
boat, and have satisfied all the hydraulic, mounting, and connection
considerations for your particular installation, you can begin mounting
and connecting the components.

Notice
Do not remove the in-line fuse holder from the battery cable when
connecting to the battery. If you remove the in-line fuse holder, you will
void the GHP 10 warranty and possibly damage the GHP 10 autopilot
system.

Shadow Drive Installation

You should connect the ECU power cable directly to the boat battery
if possible. Although it is not recommended, if you connect the power
cable to a terminal block or other source, connect it through a 40 A fuse.

Connecting the Shadow Drive to the Hydraulics
Before you can install the Shadow Drive, you must select a location at
which to connect the Shadow Drive to the hydraulic steering of your
boat, after you have read and followed the mounting and connection
considerations (page 5). For more information, consult the hydrauliclayout diagrams found in the installation instructions included in the
pump box.

If you plan to route the ECU through a breaker or a switch near the
helm, consider using an appropriately sized relay and control wire
instead of extending the ECU power cable.

To install the Shadow Drive, connect it to the hydraulic steering line of
your boat and connect it to the CCU/ECU interconnect cable.

Use the included connectors to install the Shadow Drive in the
hydraulic line.
Connecting the Shadow Drive
When connecting the Shadow Drive to the hydraulic system, follow the
important considerations (page 5).

1. Route the connector-terminated end of the ECU power cable to the
ECU, but do not connect it to the ECU.
2. Route the bare-wire end of the ECU power cable to the boat battery.
If the wire is not long enough, it can be extended.
3. Determine the correct wire gauge for an extended run, based on the
table below.
Length of the Extension
10 ft. (3 m)
15 ft. (4.5 m)
20 ft. (6 m)
25 ft. (7.5 m)

To connect the Shadow Drive, connect it to the CCU/ECU interconnect
cable.
1. Route the bare-wire end of the CCU/ECU interconnect cable to the
Shadow Drive.
If the cable is not long enough, extend the appropriate wires with 28
AWG wire.
2. Connect the cables, based on the table below.
Shadow Drive Wire Color CCU/ECU Interconnect Cable Wire
Color
Red (+)

Brown (+)

Black (-)

3. Solder and cover all bare-wire connections.

ECU Installation

To install the ECU, mount it to your boat (page 10), connect it to the
pump and to the CCU (page 11), and connect it to the boat battery
(page 10).
ECU on a 24 Vdc System
The ECU hardware has been updated to function with 24 Vdc electrical
systems, though older ECU units run on only 12 Vdc electrical systems.
To determine if your ECU is compatible with a 24 Vdc system, examine
the serial number on the ECU (page 5).

4.
5.
6.

Recommended Wire Gauge
12 AWG (3.31 mm2)
10 AWG (5.26 mm2)
10 AWG (5.26 mm2)
8 AWG (8.36 mm2)

Connect the black wire (-) to the negative (-) terminal of the battery.
Connect the red wire (+) to the positive (+) terminal of the battery.
Do not connect the ECU power cable to the ECU.
Connect the power cable to the ECU only after you install all of
the other GHP 10 components.

CCU Installation

To install the CCU, you must mount it to your boat (page 10), connect
it to the ECU (page 11), connect it to a NMEA 2000 network (page 12),
and connect it to the alarm (page 11) and to the yellow CCU signal wire
on the GHC 10 (page 11).
Installing the CCU Mounting Bracket
Before you can mount the CCU, you must select a location and
determine the correct mounting hardware (page 5).
The CCU bracket has two portions, the mounting portion and the
securing portion.
1. Cut out the mounting template provided on page 23.
2. Tape the template to the mounting location.
If you are installing the CCU on a vertical surface, install the
mounting portion of the bracket with an opening ➊ at the bottom.

Note: The GHP 10 system software (CCU software) must be version
2.70 or newer in order to support 24 Vdc installations.
Mounting the ECU
Before you can install the ECU, you must select a mounting location
and determine the correct mounting hardware (page 5).
1.
2.
3.
4.

Cut out the mounting template provided on page 23.
Tape the template to the mounting location.
Drill pilot holes at the four mounting locations.
Use screws to mount the ECU.

➋

➊
3. Drill pilot holes at the three mounting locations.
4. Use screws ➋ to secure the mounting portion of the CCU bracket.

GHP 10 Installation Instructions

Securing the CCU in the CCU Bracket
1. Connect the CCU/ECU
➌
interconnect cable and the NMEA
2000 drop cable to the CCU.
2. Place the CCU in the mounting
portion of the CCU bracket with
the wires hanging straight down
➊.
3. Place the securing portion of the
bracket over the ball and snap
it into the mounting portion of
➋
the bracket, starting with the
two arms ➋ that do not have the
thumbscrew ➌.
➊
4. With the cables hanging straight
down, connect the arm with the thumbscrew.
The cables must hang straight down for the CCU to accurately read
your heading.
5. Hand-tighten the thumbscrew until the CCU is held firmly in the
bracket.
Do not overtighten the thumbscrew.

Alarm Installation

Connecting the CCU
1. Route the six-pin connector end of the CCU/ECU interconnect cable
to the ECU and make the connection.
2. Route the wires from the bare-wire portion of the cable to the CCU/
ECU interconnect cable.
• Route the red and blue wires to the location where you plan to
install the alarm (page 11).
If the cable is not long enough, extend the appropriate wires with
28 AWG (.08 mm2) wire.
• Route the yellow wire to the location where you plan to install
the GHC 10 (page 11).
If the cable is not long enough, extend the yellow wire with 22
AWG (.33 mm2) wire.
3. Cut and tape the remaining bare wires; they are not used.

3. Solder and cover all bare-wire connections.

Connecting the GHP to the Tachometer
1. If you are connecting analog tachometry, identify the location and
connection assignments for the tachometer (or tachometers) on your
boat.
2. Route the bare-wire end of the CCU/ECU interconnect cable to the
tachometer (or tachometers).
If the cable is not long enough, extend the wires with twisted pair,
22 AWG wire.
3. Connect the cables, based on the table below.
Engine
Configuration

Tachometer

Ground

Single engine

Green and violet (twist
together)

White and grey (twist
together)

Dual engines

Port engine = violet

Port engine = grey

Starboard engine = green

Starboard engine =
white

4. Connect the tachometer wire or wires from the CCU/ECU
interconnect cable to the tachometer sensor wire or wires from the
engine (or engines). Connect the ground wires to a clean ground.
Note: For three or more outboard engines, connect to the
outermost port and starboard engines, according to the table.
5. Solder and cover all bare-wire connections.
GHP 10 Installation Instructions

The alarm audibly alerts you to important GHP 10 events.
To install the alarm, you must mount it to your boat (page 10), connect
it to the CCU (page 10), and connect it to the yellow CCU signal wire
on the GHC 10 (page 11).
Mounting the Alarm
Before you can mount the alarm, you must select a mounting location
(page 5).
Secure the alarm with cable ties or other appropriate mounting
hardware (not included).
Connecting the Alarm
1. Route the alarm-cable to the bare-wire end of the CCU/ECU
interconnect cable.
If the cable is not long enough, extend the appropriate wires with 28
AWG (.08 mm2) wire.
2. Connect the cables, based on the table below.
Alarm Wire Color CCU/ECU Interconnect Cable Wire Color
White (+)
Red (+)
Black (-)
Blue (-)

GHC 10 Installation

Install the GHC 10 by flush-mounting it in the dashboard near the helm,
connecting it to the yellow wire from the CCU/ECU interconnect cable,
and connecting it to a NMEA 2000 network.
To use advanced features of the GHP 10, optional NMEA
2000-compatible or NMEA 0183-compatible devices, such as a GPS
device, can be connected to the NMEA 2000 network or connected to
the GHC 10 through NMEA 0183.
Mounting the GHC 10
Notice
The temperature range for the GHC 10 is from 5°F to 158°F (from
-15°C to 70°C). Extended exposure to temperatures outside of this
range (in storage or operating conditions) may cause failure of the
LCD screen or other components. This type of failure and related
consequences are not covered by the manufacturer’s limited warranty.
If you are mounting the GHC 10 in fiberglass, when drilling the
four pilot holes, it is recommended to use a countersink bit to drill a
clearance counterbore through only the top gel-coat layer. This will
help to avoid any cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass and
overtightened. Garmin recommends applying an anti-galling, stainless
anti-seize lubricant to the screws before installing them.
Before you can mount the GHC 10, you must select a mounting location
(page 5).
1. Trim the flush-mount template and ensure it will fit in the location
where you plan to mount the GHC 10.
The flush-mount template is included in the product box, not in
these instructions.
The flush-mount template has adhesive on the back.
2. Remove the protective liner from the adhesive on the back of the
template and apply it to the location where you plan to mount the
GHC 10.

3. If you will be cutting the hole with a jigsaw instead of a 317/32 in. (90
mm) hole saw, use a 3/8 in. (10 mm) drill bit to drill a pilot hole as
indicated on the template to begin cutting the mounting surface.
4. Using the jigsaw or the 3.5 in. (90 mm) hole saw, cut the mounting
surface along the inside of the dashed line indicated on the flushmount template.
5. If necessary, use a file and sandpaper to refine the size of the hole.
6. Place the GHC 10 into the cutout to confirm that the four mounting
holes are correct.
7. Select an option:
• If the mounting holes are correct, proceed to step 8.
• If the mounting holes are not correct, mark the correct locations
of the four mounting holes.
8. Remove the GHC 10 from the cutout.
9. Drill the four 1/8 in. (3.2 mm) pilot holes.
If you are mounting the GHC 10 in fiberglass, use a countersink bit
as advised in the notice.
10. Remove the remainder of the template.
11. Place the GHC 10 into the cutout.
12. Securely fasten the GHC 10 to the mounting surface using the
supplied screws.
If you are mounting the GHC 10 in fiberglass, use a anti-galling
lubricant as advised in the notice.
13. Snap the mounting covers ➊ into place.

you turn it off, and the autopilot remains on until turned off by
the primary GHC 10.

Connecting the Devices to a NMEA 2000
Network
Notice
If you have an existing NMEA 2000 network on your boat, it should
already be connected to power. Do not connect the included NMEA
2000 power cable to an existing NMEA 2000 network, because only
one power source should be connected to a NMEA 2000 network.
You can connect the GHC 10 to the CCU through an existing NMEA
2000 network. If you do not have an existing NMEA 2000 network on
your boat, all the parts needed to build one are supplied in the GHP 10
package (page 13).
To use advanced features of the GHP 10, optional NMEA
2000-compatible devices, such as a GPS device, can be connected to
the NMEA 2000 network.
For more information on NMEA 2000, go to www.garmin.com.
Connecting the GHC 10 to an Existing NMEA 2000
Network
1. Determine where to connect the GHC 10 ➊ to your existing NMEA
2000 backbone ➋ (page 5).

➊
➊
Connecting the GHC 10
For the autopilot system to function correctly, you must connect two
wires from the GHC 10 data cable (yellow and black).
1. Connect the yellow wire from the GHC 10 data cable to the yellow
wire from the CCU/ECU interconnect cable.
If the cable is not long enough, extend the yellow wire with 22
AWG (.33 mm2) wire.
2. Connect the black wire from the GHC 10 data cable to the same
ground location as the ECU.
If the cable is not long enough, extend the black wire with 22 AWG
(.33 mm2) wire.
3. Solder and cover all bare-wire connections.
Multiple GHC 10 Considerations
You can install multiple GHC 10 devices (sold separately) to control the
autopilot from different locations on the boat.
• All additional GHC 10 devices must be at software version 3.0 or
later.
• All additional GHC 10 devices must be connected to the
NMEA 2000 network (page 12).
• To use an additional GHC 10 to turn on the autopilot, connect the
yellow and black wires from the additional GHC 10 to the same
wires as the primary GHC 10.
◦◦ If you connect additional GHC 10 devices to turn on the
autopilot, you must turn them all off to turn off the autopilot.
◦◦ If you do not connect an additional GHC 10 to turn on the
autopilot, then the additional GHC 10 enters standby mode when
12

➍
➌
➋
2. Disconnect one side of a NMEA 2000 T-connector from the
network.
3. If necessary, to extend the NMEA 2000 network backbone, connect
a NMEA 2000 backbone extension cable (not included) to the side
of the disconnected T-connector.
4. Add the included T‑connector ➌ for the GHC 10 to the NMEA
2000 backbone by connecting it to the side of the disconnected
T‑connector or backbone extension cable.
5. Route the included drop cable ➍ to the bottom of the T-connector
added in step 4, and connect it to the T-connector.
If the included drop cable is not long enough, you can use a drop
cable up to 20 ft. (6 m) long (not included).
6. Connect the drop cable to the to the GHC 10.

GHP 10 Installation Instructions

7. Connect the drop cable to the T-connector you added in step 3, and
to the GHC 10.
NOTE: In order for the autopilot to turn on, the yellow wire from
the GHC 10 data cable be connected to the yellow wire from the
CCU/ECU interconnect cable, and the black wire from the GHC 10
data cable must be connected to the same ground as the ECU
(page 12).

Building a Basic NMEA 2000 Network for the GHC 10 and
the CCU

Connecting the CCU to an Existing NMEA 2000 Network
1. Determine where to connect the CCU ➊ to your existing NMEA
2000 backbone ➋ (page 5).

1. Connect the three T-connectors ➊ together by their sides.

Notice
You must connect the included NMEA 2000 power cable to the boat
ignition switch, or through another in-line switch. The GHC 10 will
drain your battery if the NMEA 2000 power cable is connected to the
battery directly.

➏

➊

➐

➍
+

➌
➊

➎
➋

➍
➑
➌
➋
2. Disconnect one side of a NMEA 2000 T-connector from the
network.
3. If necessary, to extend the NMEA 2000 network backbone, connect
a NMEA 2000 backbone extension cable (not included) to the side
of the disconnected T-connector.
4. Add the included T‑connector ➌ for the CCU to the NMEA
2000 backbone by connecting it to the side of the disconnected
T‑connector or backbone extension cable.
5. Route the included drop cable ➍ to the bottom of the T-connector
added in step 4, and connect it to the T-connector.
If the included drop cable is not long enough, you can use a drop
cable up to 20 ft. (6 m) long (not included).
6. Connect the drop cable to the to the CCU.

GHP 10 Installation Instructions

➑

2. Connect included NMEA 2000 power cable ➋ to a 12 Vdc power
source ➌ through a switch.
Connect to the ignition switch ➍ of the boat if possible, or through
an in-line switch (not included).
3. Connect the NMEA 2000 power cable to one of the T-connectors.
4. Connect one of the included NMEA 2000 drop cables ➎ to one of
the T-connectors and to the GHC 10 ➏.
5. Connect the other included NMEA 2000 drop cable to the other
T-connector and to the CCU ➐.
6. Connect the male and female terminators ➑ to each end of the
combined T-connectors.
NOTE: The GHC 10 must connect to the CCU with the yellow
CCU signal wire in the GHC 10 data cable. The black wire must
connect to ECU ground (page 12).

Connecting Optional Devices to the GHP 10
Autopilot System

To use advanced features of the GHP 10, optional NMEA
2000-compatible or NMEA 0183-compatible devices, such as a GPS
device, can be connected to the NMEA 2000 network or to the GHC 10
through NMEA 0183.
NMEA 0183 Connection Considerations
• To identify the Transfer (Tx) A(+) and B(-) wires for your NMEA
0183-compatible device, consult the installation instructions for
your device.
• When connecting NMEA 0183 devices with two transmitting and
two receiving lines, it is not necessary for the NMEA 2000 bus and
the NMEA 0183 device to connect to a common ground.
• When connecting a NMEA 0183 device with only one transmitting
(Tx) line or with only one receiving (Rx) line, the NMEA 2000
bus and the NMEA 0183 device must be connected to a common
ground.
Connecting an Optional NMEA 0183-compatible Device to
the GHC 10
1. Determine the NMEA 0183 connection assignments of your NMEA
0183-compatible device.
2. Connect your NMEA 0183-compatible device to the GHC 10, based
on the table below.
GHC 10 Data Cable Wire Color
Black
Yellow
Blue
White
Brown
Green

Function
CCU signal ground
CCU signal
Tx/A (+)
Tx/B (-)
Rx/A (+)
Rx/B (-)

Three examples of various connection situations are provided in the
appendix (page 18).
3. If necessary, use 22 AWG (.33 mm2) twisted-pair wire for extended
runs of wire.
4. Solder and cover all bare-wire connections.

Configuring the GHP 10
The GHP 10 must be configured and tuned to your boat dynamics and
motor configuration. Use the Dockside Wizard and the Sea Trial Wizard
on the GHC 10 to configure the GHP 10. These wizards walk you
through the necessary configuration steps.

About the Dockside Wizard
Notice
If you perform the Dockside Wizard while your boat is out of the water,
provide rudder-movement clearance to avoid damage to the rudder or
other objects.
You can complete the Dockside Wizard while your boat is in or out
of the water. If your boat in the water, it must be stationary while you
complete the wizard.

Starting the Dockside Wizard

1. Turn on the GHP 10.
The first time you turn on the GHP 10, you are prompted to
complete a short setup sequence on the GHC 10.
2. If necessary, complete the setup sequence.
3. After you complete the initial setup, select an option:
• If the Dockside Wizard starts automatically, proceed to step 4.
• If the Dockside Wizard does not start automatically, select
Menu > Setup > Dealer Autopilot Configuration > Wizards >
Dockside Wizard.
4. Select Begin.

Performing the Dockside Wizard

1. Start the Dockside Wizard (page 14).
2. Select the vessel type.
3. Select the number turns it takes for your helm to go from lock to
lock (page 14).
4. Select the helm displacement (page 14).
5. Test the steering direction (page 14).
6. Select the speed source (page 15).
7. If necessary, verify the tachometer (page 15).
8. Review the wizard results (page 15).
Calibrating Lock-to-Lock Turns
1. Count the number of turns it takes your helm to go from lock to lock
(fully turned port to fully turned starboard).
2. Use the arrows on the GHC 10 to enter the turns you counted (the
default is 4.5).
3. Select Done.
Calibrating Helm Displacement
The helm displacement is usually written on the body of the helm
pump. If you are unsure, consult the manufacturer of your boat for the
helm displacement value.
1. Use the arrows on the GHC 10 to enter the helm displacement value
(the default is 1.7 in3).
2. Select Done.
Testing the Steering Direction
1. Use the arrows on the GHC 10 to test the steering direction.
When you select the right arrow, the rudder should turn so that the
boat would steer to the right, and when you select the left arrow, the
rudder should turn so that the boat would steer to the left.

GHP 10 Installation Instructions

2. Select Continue.
3. Select an option:
• If the steering test turns the boat in the correct direction, select
Yes.
• If the steering test turns the boat in the opposite direction, select
No.
4. If you selected No in step 3, repeat steps 1–2.
NOTE: If it is incorrect, the steering direction can also be changed
during the autotune procedure (page 16).
Selecting the Speed Source
Select an option:
• If you connected a NMEA 2000-compatible engine (or engines)
to the NMEA 2000 network, select NMEA 2000.
• If you did not connect a NMEA 2000-compatible engine (or
engines), select the engine (or engines) to which you connected
the tachometer sensor from the CCU.
◦◦ For a single-engine boat, select Port.
• If tachometer data is unavailable or unusable, select GPS data as
a speed source.
◦◦ When GPS data is used as a speed source, the maximum
speed for all vessel types must be configured.
• If you did not connect a speed source, select None.
◦◦ If the autopilot does not perform well using None as the
speed source, Garmin recommends connecting a tachometer
or GPS as the speed source.
Verifying the Tachometer
This procedure does not appear if GPS or None is selected as the speed
source.
1. With the engine (or engines) running, compare the RPM readings on
the GHC 10 with the tachometer (or tachometers) on the dashboard
of your boat.
2. If the values do not match, use the arrows to adjust the Pulses Per
Rev values.
NOTE: When you adjust the Pulses Per Rev with the arrows, there
is a delay before the new RPM readings appear on the GHC 10.
Ensure you wait until the GHC 10 adjusts to the new reading for
each adjustment.

• Ensure your boat is not significantly affected by the wind.
• Keep the weight on your boat balanced. DO NOT move around
on the boat while completing any of the steps in the Sea Trial
Wizard.

Starting the Sea Trial Wizard

Before you start the Sea Trial Wizard, you must drive to an open area of
calm water.
1. Turn on the GHP 10.
2. Select an option:
• If the Sea Trial Wizard starts automatically, proceed to step 3.
• If the Sea Trial Wizard does not start automatically, select Menu
> Setup > Dealer Autopilot Configuration > Wizards > Sea
Trial Wizard.
3. Select Begin.

Performing the Sea Trial Wizard

1. Drive your boat to an open area of calm water.
2. Start the Sea Trial Wizard (page 15).
3. If necessary, configure the planing RPM (page 15).
4. If necessary, configure the planing speed (page 15).
5. If necessary, configure the high RPM limit (page 15).
6. If necessary, configure the maximum speed (page 15).
7. Calibrate the compass (page 16).
8. Perform the autotune procedure (page 16).
9. Set north (page 16).
10. If necessary, set the fine heading adjustment (page 16).
Configuring the Planing RPM
NOTE: This procedure does not appear if you select displacement hull
as your vessel type, or if you select None as the speed source.
1. Note the RPM reading from the tachometer on the dashboard of
your boat at the point your boat transitions from displacement to
planing speed.
2. If the tachometer value does not match the value on the GHC 10,
use the arrows to adjust the value.
3. Select Done.

Reviewing the Results of the Dockside Wizard
The GHC 10 displays the values you chose when you ran the Dockside
Wizard.

Configuring the Planing Speed
NOTE: This procedure appears only when GPS is selected as the speed
source and Planing Hull is selected as the vessel type.

1.
2.
3.
4.
5.

1. Use the arrows on the GHC 10 to adjust the value.
2. Select Done.

Examine the results of the Dockside Wizard.
Select any incorrect value and select Select.
Correct the value.
Repeat steps 2 and 3 for all incorrect values.
When you are finished reviewing the values, select Done.

About the Sea Trial Wizard

The Sea Trial Wizard configures the fundamental sensors on the
autopilot, and it is extremely important to complete the wizard in
conditions appropriate for your boat.

Important Sea Trial Wizard Considerations

Complete the Sea Trial Wizard in calm water. The nature of calm water
is relative to the size and shape of your boat.

Configuring the High RPM Limit
NOTE: This procedure appears only when GPS is selected as the speed
source.
1. Use the arrows on the GHC 10 to adjust the value.
2. Select Done.
Configuring the Maximum Speed
NOTE: The procedure appears only when GPS is selected as the speed
source.
1. Use the arrows on the GHC 10 to adjust the value.
2. Select Done.

• Ensure your boat does not rock while sitting still or moving very
slowly.
GHP 10 Installation Instructions

Calibrating the Compass
1. Drive your boat at cruising speed in a straight line.
2. Select Begin, and continue to drive in a straight line.
3. When instructed, turn the boat slowly clockwise, taking care to
make the turn as steady and flat as possible.
Turn slowly so that the boat DOES NOT list.
After you successfully complete the calibration, the GHC 10
displays a completion message.
4. Select an option:
• If the calibration completes successfully, select Done.
• If the calibration fails, select Retry and repeat steps 1–3.
Performing the Autotune Procedure
Before you can perform the autotune procedure, you must have a large
stretch of open water available.
1. If you have a non-planing vessel, adjust the throttle so the boat
travels at a typical cruising speed that provides responsive steering.
If you have a planing vessel, adjust the throttle so the boat travels
below planing speed.
2. Select Begin.
The boat performs a number of zigzag motions while the Autotuning
is in progress.
The GHC 10 displays a completion message.
3. Select an option:
• If the autotune completed successfully, select Done and take
manual control of the boat.
• If the autotune failed, adjust the throttle and select Retry
Autotune.
• If the autotune failed, and the rudder went hard over or the boat
went in a circle, select Reverse Steering Dir. and Retry.
• If you receive an Error: ECU Drive Circuit Overload. See
manual for tips on reducing load error message, see the tips on
page 17.
4. If autotune fails again, repeat steps 1–3 until the autotune completes
successfully.
5. If the autotune procedure continues to fail after you reach maximum
cruising speed, reduce your speed to the initial autotune speed
and select Alternate Autotune to begin an alternate autotuning
procedure.
Setting North
Before you can set north, you must have at least 45 seconds of hazardfree, open water available.
This procedure appears if you connect an optional GPS device to the
GHP 10 (page 14), and the device has acquired a GPS position. If you
do not have a GPS device connected, you are prompted to set the fine
heading adjustment (page 16).
1. Drive the boat in a straight line at cruising speed, and select Begin.
The GHC 10 displays a completion message when the calibration is
compete.
2. Select an option:
• If the calibration completed successfully, select Done.
• If the calibration failed, repeat steps 1–2.

1. Using a handheld compass, identify north.
2. Adjust the fine heading setting until it matches north on the
magnetic compass.
3. Select Done.

Evaluating the Results of the Autopilot
Configuration

1. Test the autopilot at a slow speed.
2. If necessary, adjust the gain setting (page 17).
3. If you receive an Error: ECU Drive Circuit Overload. See manual
for tips on reducing load error message, see the tips on page 17.
4. Test the autopilot at a higher speed (normal operating conditions).
5. If necessary, adjust the gain and acceleration limiter settings.
Testing and Adjusting the Autopilot Configuration
1. Drive the boat in one direction with the autopilot engaged (heading
hold).
The boat should not oscillate significantly; however, a small amount
of oscillation is normal.
2. Turn the boat in one direction using the autopilot and observe the
behavior.
The boat should turn smoothly, not too quickly or too slowly.
When you turn the boat using the autopilot, the boat should
approach and settle on the desired heading with minimal overshoot
and oscillation.
3. Select an option:
• If the boat turns too quickly or too sluggishly, adjust the
autopilot acceleration limiter (page 16).
• If the heading hold oscillates significantly or the boat does not
correct when turning, adjust the autopilot gain (page 17).
• If you receive an Error: ECU Drive Circuit Overload. See
manual for tips on reducing load error message, see the tips on
page 17.
• If the boat turns smoothly, the heading hold oscillates only
slightly or not at all, and the boat adjusts the heading correctly,
proceed to step 5.
4. Repeat steps 2 and 3 until the boat turns smoothly the heading hold
oscillates only slightly or not at all, and the boat adjusts the heading
correctly.
5. For planing vessels, repeat steps 1–4 at faster speeds (page 16).
Adjusting the Acceleration Limiter Settings
NOTE: When you manually adjust the acceleration limiter, make
relatively small adjustments. Test the change before making additional
adjustments.
1. Enable the advanced configuration procedure (page 17).
2. On the GHC 10, select Menu > Setup > Dealer Autopilot
Configuration > Autopilot Tuning > Acceleration Limiter.
3. Select an option:
• Increase the setting if the autopilot turns too quickly,
• Decrease the setting if the autopilot turns too slowly.
4. Test the autopilot configuration.
5. Repeat steps 2 and 3 until the GHP 10 performance is satisfactory.

Setting the Fine Heading Adjustment
This procedure appears only if you do not have an optional GPS device
connected to the GHP 10 (page 14). If you do have a GPS device
installed on your boat that has acquired a GPS position, are prompted to
set north instead (page 16).
16

GHP 10 Installation Instructions

Adjusting the Autopilot Gain Settings
NOTE: When you manually adjust the rudder gain (or counter gain),
make relatively small adjustments, and adjust only one value at a time.
Test the change before making additional adjustments.
1. Enable the advanced configuration procedure (page 17).
2. On the GHC 10, select Menu > Setup > Dealer Autopilot
Configuration > Autopilot Tuning > Rudder Gains.
3. Select an option:
• Select Low Speed or High Speed and use the arrows on the
GHC 10 to adjust how tightly the rudder holds the heading and
makes turns at low speed or high speed.
If you set this value too high, the autopilot may be overactive,
attempting to constantly adjust the heading at the slightest
deviation. An overactive autopilot can cause excess wear and
tear on the drive unit, and drains the battery at a faster-thannormal rate.
• Select Low Speed Counter or High Speed Counter to adjust
how tightly the rudder corrects the turn overshoot. If you set this
value too high, the autopilot can overshoot the turn again when
attempting to counter the original turn.
4. Test the autopilot configuration.
5. Repeat steps 2 and 3 until the GHP 10 performance is satisfactory.

5. Select Done.
6. Test the rudder rate limiter settings.
7. Repeat steps 2–6 until rudder rate limiter performance is
satisfactory.
8. Perform the autotune procedure.

Advanced Configuration Procedure

Advanced configuration options are not available on the GHC 10 under
normal conditions. To access the advanced configuration settings of the
GHP 10, enable the advanced configuration procedure.
Enabling the Advanced Configuration Procedure
1. From the heading screen, select Menu > Setup > System > System
Information.
2. Press and hold the center soft key ➊ for 5 seconds.
Dealer Mode appears.

➊

Reducing the Risk of ECU Drive Circuit Overload
If you receive an Error: ECU Drive Circuit Overload. See manual
for tips on reducing load error message, use these tips to help reduce
the load:

3. Press Back > Back.
If the option for Dealer Autopilot Configuration is available on the
Setup screen, the advanced configuration procedure is enabled.

• Ensure the appropriate pump has been correctly installed on your
boat.
• If possible, use larger inside diameter hydraulic hoses on your
steering system.
• Mount the pump closer to the cylinder to limit the length of the hose
runs.
• Eliminate unneeded hydraulic fittings in the hydraulic fittings.
• If overloading occurs during the autotune procedure, skip the
procedure and manually tune the autopilot.
• Increase the rudder rate limiter setting to slow the fluid rate.
• Reduce rudder gain to limit pump activity.

Advanced Configuration Settings

Adjusting the Rudder Rate Limiter
If the ECU Drive Circuit Overload. See manual for tips on reducing
load error message continues to appear, you may need to adjust the
rudder rate limiter.
NOTE: Complete rudder rate adjustments only at the dock or while
your boat is not moving.
NOTE: If you adjust the rudder rate limiter, you must perform the
autotune procedure.
1. Enable the advanced configuration procedure (page 17).
2. On the GHC 10, select Menu > Setup > Dealer Autopilot
Configuration > Autopilot Tuning > Rudder Rate Limiter.
3. Select Continue.
Autopilot takes control of the rudder.
4. Use the arrows on the GHC 10 to adjust the speed of the limiter.
• 0% is the is the default speed for the rudder rate limiter.
• Lower rudder rate limiter numbers allow the rudder to move
faster between the right rail and left rail.
• Lower rudder rate limiter numbers increase the running current.
• Higher rudder rate limiter numbers decrease the running current.
GHP 10 Installation Instructions

You can run the Autotune automated configuration process, calibrate the
compass, and define north on the GHP 10 through the GHC 10 without
running the wizards. You can also define each setting individually,
without running the configuration processes.
Manually Running the Automated Configuration
Procedures
1. Enable the advanced configuration procedure (page 17).
2. From the Heading screen, select Menu > Setup > Dealer Autopilot
Configuration > Automated Setup.
3. Select Autotune, Calibrate Compass, or Set North.
4. Follow the on-screen instructions (page 14).
Manually Running the Dockside and Sea Trial Wizards
The Dockside Wizard and the Sea Trial Wizard allow you to quickly
define all of the important configuration settings on the GHP 10. After
running the wizards, if you do not feel the GHP 10 is working correctly,
you can run the wizards again at any time. To access the wizards, enable
the advanced configuration procedure (page 17).
Manually Defining Individual Configuration Settings
1. Enable the advanced configuration procedure (page 17).
2. From the Heading screen, select Menu > Setup > Dealer Autopilot
Configuration.
3. Select the setting category.
4. Select a setting to configure.
Descriptions of each setting are available in the appendix (page 20).
5. Configure the value of the setting.
NOTE: Configuring certain settings in the advanced configuration
procedure may require you to modify other settings. Review the GHP
10 Configurations Settings section (page 20) prior to modifying any
settings.
17

Appendix

Wire

NMEA 0183 Connection Diagrams

➊

The following three connection diagrams are examples of different
situations you may encounter when connecting your NMEA 0183
device to the GHC 10.
Example One of Three: Two-way NMEA 0183 Communication

➌

>
>

➊
➋

>
>

➍

>
>

➎

Example Three of Three: Only One Transmitting Wire

If your NMEA 0183-compatible device has only one transmitting
wire (Tx), connect it to the brown wire (Rx/A) from the GHC 10, and
connect the green wire (Rx/B) from the GHC 10 to NMEA ground.

➋
+

➊

NMEA 0183-Compatible Device Wire
Function
Power
NMEA 0183 ground
Rx/A (+)
Rx/B (-)
Tx/A (+)
Tx/B (-)

NOTE: When connecting NMEA 0183 devices with two transmitting
and two receiving lines, it is not necessary for the NMEA 2000 bus and
the NMEA 0183 device to connect to a common ground.
If your NMEA 0183-compatible device has only one receiving wire
(Rx), connect it to the blue wire (Tx/A) from the GHC 10, and leave the
white wire (Tx/B) from the GHC 10 unconnected.

➋
+

➊

➍
>
>

➌
➌
➎
➏

>
>
>

➊
➋
➌
➍

➌
➋
➌
➍
➎

➊
>
>

➍

GHC 10
NMEA 2000 network (provides power to the GHC 10)
12 VDC power source
NMEA 0183-compatible device

Wire
➊
➋

Example Two of Three: Only One Receiving Wire

➍

GHC 10
NMEA 2000 network (provides power to the GHC 10)
12 VDC power source
NMEA 0183-compatible device

Wire GHC 10 Wire
Color - Function
N/A
➊
N/A
➋
Blue - Tx/A (+)
➌
White - Tx/B (-)
➍
Brown - Rx/A (+)
➎
Green - Rx/B (-)
➏

➊
➋
➌
➍

➌

NMEA 0183-Compatible Device
Wire Function
Power
NMEA 0183 ground
Rx
N/A
Tx/A (+)
Tx/B (-)

NOTE: When connecting a NMEA 0183 device with only one
receiving (Rx) line, the NMEA 2000 bus and the NMEA 0183 device
must be connected to a common ground.

➌
➍
➎
➏

>
>

➊
➋
➌
➍

➋

➏

➋

➊

GHC 10 Wire
Color - Function
N/A
N/A
Blue - Tx/A (+)
White - unconnected
Brown - Rx/A (+)
Green - Rx/B (-)

➌
➍
➎

GHC 10 Wire
Color - Function
N/A
Green - Rx/B - connect
to NMEA 0183 ground
Blue - Tx/A (+)
White - Tx/B (-)
Brown - Rx/A (+)

NMEA 0183-Compatible Device
Wire Function
Power
NMEA 0183 ground
Rx/A (+)
Rx/B (-)
Tx/A (+)

NOTE: When connecting a NMEA 0183 device with only one
transmitting (Tx) line, the NMEA 2000 bus and the NMEA 0183 device
must be connected to a common ground.

➊
➋

>
>
>

GHC 10
NMEA 2000 network (provides power to the GHC 10)
12 VDC power source
NMEA 0183-compatible device

➍

Specifications
Device
ECU

Specification Measurement
Dimensions
(W × H × D) 6 19/32 × 4 19/32 × 2 in.
(167.6 × 116.8 × 50.8 mm)
Weight
1.5 lb. (0.68 kg)
Temperature From 5°F to 131°F (from -15°C to 55°C)
range
Case material Fully gasketed, high-impact aluminum
alloy, waterproof to IEC 529 IPX7
standards
Power cable
9 ft. (2.7 m)
length
Input power
11.5–30 Vdc
Fuse
40 A, blade-type
Main power
1 A (not including the drive unit)
usage
GHP 10 Installation Instructions

Device
CCU

Alarm

GHC 10

Specification
Dimensions
Weight
Temperature
range
Case material
CCU/ECU
interconnect
cable length
NMEA 2000
LEN
Dimensions
Weight
Temperature
range
Cable length
Dimensions
Weight
Cables

Measurement
3 19/32 in. diameter (91.4 mm)
5.6 oz. (159 g)
From 5°F to 131°F (from -15°C to 55°C)

059392

ISO Acknowledgment

059904

ISO Request

060928

ISO Address Claim

126208

NMEA - Command/Request/Acknowledge
Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

127250

Vessel Heading

Type

PGN

Description

Receive

059392

ISO Acknowledgment

059904

ISO Request

060928

ISO Address Claim

126208

NMEA - Command/Request/Acknowledge
Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

127245

Rudder Data

127250

Vessel Heading

127488

Engine Parameters - Rapid Update

128259

Water Speed

129025

Position - Rapid Update

129029

GNSS Position Data

129283

Cross-Track Error

129284

Navigation Data

129285

Navigation - Route/WP information

130306

Wind Data

130576

Small Craft Status

059392

ISO Acknowledgment

059904

ISO Request

060928

ISO Address Claim

126208

NMEA - Command/Request/Acknowledge
Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

128259

Water Speed

129025

Position - Rapid Update

129026

COG & SOG - Rapid Update
Cross Track Error

Fully gasketed, high-impact aluminum
alloy, waterproof to IEC 529 IPX7
standards
16 ft. (5 m)

GHC 10

2 (100 mA)
(L × Diameter) / × 1 in. (23 × 25 mm)
2.4 oz. (68 g)
From 5°F to 131°F (from -15°C to 55°C)
29 32

10 ft. (3.0 m)
4 5/16 × 4 3/8 × 1 29/32 in. (109 × 111 × 48
mm)
9.6 oz. (272 g)
NMEA 0183 data cable – 6 ft. (1.8 m)
NMEA 2000 drop cable and power cable –
6 1/2 ft. (2 m)
From 5°F to 158°F (from -15°C to 70°C)

Temperature
range
Compass-safe 9 1/2 in. (241 mm)
distance
Case material Fully gasketed, high-impact aluminum
alloy, waterproof to IEC 529 IPX7
standards
GHC 10 power 2.5 W max.
usage
NMEA 2000
9–16 Vdc
input voltage
NMEA 2000
6 (300 mA)
LEN

NMEA 2000 PGN Information
CCU

Transmit

Type

PGN

Description

Receive

059392

ISO Acknowledgment

059904

ISO Request

060928

ISO Address Claim

126208

NMEA - Command/Request/Acknowledge
Group Function

Transmit

126464

Transmit/Receive PGN List Group Function

129283

126996

Product Information

129284

Navigation Data

127258

Magnetic Variation

129540

GNSS Sats in View

127488

Engine Parameters - Rapid Update

130306

Wind Data

129025

Position - Rapid Update

129026

COG & SOG - Rapid Update

129283

Cross Track Error

129284

Navigation Data

GHP 10 Installation Instructions

The GHP 10 and the GHC 10 are NMEA 2000 certified.

NMEA 0183 Information

When connected to optional NMEA 0183-compatible devices, the
GHC 10 uses the following NMEA 0183 sentences.
Type
Receive

Transmit

Sentence
wpl
gga
grme
gsa
gsv
rmc
bod
bwc
dtm
gll
rmb
vhw
mwv
xte
hdg

Category

Setting

Description

Rudder Gains

High Speed
Gain

Allows you to set the rudder
gain for high speeds.
This setting applies to the
vessel when operating above
planing speed.
If you set this value too
high, the autopilot may be
overactive, attempting to
constantly adjust the heading
at the slightest deviation.
An overactive autopilot can
cause excess wear and tear
on the drive unit (page 17).

Steering System
Setup

Verify Steering
Direction

This setting tells the autopilot
which direction the rudder
must move to turn the vessel
to port and to starboard.
You can test and reverse
the steering direction if
necessary.

Steering System
Setup

Lock-to-Lock
Turns

Allows you to adjust the
number of turns it takes
your helm to go from lock to
lock (fully turned port to fully
turned starboard).

Steering System
Setup

Helm
Displacement

Allows you to calibrate helm
displacement.

Steering System
Setup

Linkage
Compensation

Allows you to adjust the
linkage compensation if the
steering is loose or sloppy.
The higher you set this
value, the more the autopilot
compensates for loose or
sloppy steering. Use this
setting with caution.

Rudder Gains

High Speed
Counter

Allows you to set the rudder
gain counter-correction for
high speeds.
This setting applies to the
vessel when operating above
planing speed.
If you set this value too
high, the autopilot may be
overactive, attempting to
constantly adjust the heading
at the slightest deviation.
An overactive autopilot can
cause excess wear and tear
on the drive unit (page 17).

NMEA Setup

NMEA
Checksum

If the connected NMEA
0183 GPS unit incorrectly
calculates checksums, you
may still be able to use it
if you turn this setting off.
When set to off, data integrity
is compromised.

NMEA Setup

Reversed XTE

If the connected NMEA 0183
GPS unit sends the incorrect
steering direction with the
cross track error signal. You
can use this setting to correct
the steering direction.

Navigation Setup

Navigation
Gain

Allows you to adjust how
aggressively the autopilot
eliminates cross-track error
while following a Route-To
pattern.
If this value is too high, the
autopilot can oscillate back
and forth across the course
line over long distances.
If this value is too low, the
autopilot may respond slowly
in eliminating cross-track
error.

Navigation Setup

Navigation
Trim Gain

Allows you to adjust the
acceptable amount of long
term cross-track error while
following a Route-To pattern.
Only adjust this setting after
the navigation gain has been
set.
If this value is too high, the
autopilot will overcompensate
for cross-track error.
If this value is too low, the
autopilot will allow a large
long term cross-track error.

GHP 10 Installation Instructions

NOTE: Advanced configuration settings are available when using
the advanced configuration procedure (page 17). Other settings are
available during normal operation of the GHP 10. See the configuration
section of the GHC 10 Owner’s Manual for more information.

Error and Warning Messages
Error Message
ECU voltage is low

Cause
The ECU supply voltage
goes below 10 Vdc for
longer than 6 seconds.
Autopilot is not
The autopilot is no
receiving navigation longer receiving valid
data. Autopilot placed navigation data.
in heading hold.
This message will
also be shown if
navigation is stopped
on a chartplotter prior
to disengaging the
autopilot.
The GHC lost
Connection with
autopilot lost
connection with CCU.
Low GHC supply
The supply voltage
voltage
level is below the value
specified in the low
voltage alarm menu.
Error: ECU high
The ECU supply voltage
voltage
goes above a certain
threshold:
• 12v system: 20 volts
• 24v system: 36 volts

Autopilot Action
• Alarm sounds
• Continues in
normal operation
• Alarm sounds
• Autopilot
transitions to
heading hold

N/A
N/A

• Alarm sounds
• Drive unit is
disabled
• GHC 10 begins a
countdown timer
that automatically
powers off the
autopilot after 60
seconds
Error: ECU high
The ECU temperature • Alarm sounds
• Drive unit is
temperature
rises above 212°F
disabled
(100°C).
• GHC 10 begins a
countdown timer
that automatically
powers off the
autopilot after 60
seconds
• Alarm sounds
The average ECU
Error: ECU Drive
• Drive unit is
Circuit Overload. See current value rises
disabled
above 16 A.
manual for tips on
• Autopilot switches
reducing load.
to standby
• Alarm sounds
Communication
Error: Lost
between the CCU and • GHC 10 begins a
communication
countdown timer
the ECU has timed out.
between ECU and
that automatically
CCU
powers off the
autopilot after 60
seconds
• Autopilot switches
Lost GPS as a speed GPS signal is lost.
source
to heading hold.
• Occurs when GPS
is selected as the
speed source.

GHP 10 Installation Instructions

ECU Mounting Template

CCU Mounting Template

➊

Up, when installing on a
vertical surface

GHP 10 Installation Instructions

GHP 10 Installation Checklist

Detach this checklist from the installation instructions and use it during the GHP 10 installation process.
Read all installation instructions before installing the GHP 10. Contact Garmin Product Support if you have any questions during the installation
process.
Refer to the diagram on page 7 and notes on page 5 to understand the necessary electrical and data connections.
Lay out all of the components and check the cable lengths. Obtain extensions if necessary.
Install the drive unit according to the instructions provided with the drive unit.
Mount the ECU (page 10). The ECU must be located within 191/2 in. (0.5 m) of the drive unit.
Connect the drive unit to the ECU.
ount the CCU (page 10) in a location free of magnetic interference. Use a handheld compass to test for magnetic interference in the area.
M
Mount the CCU in the bracket so that the wires hang straight down.
Mount the GHC 10 (page 11).
Connect the yellow wire on the GHC 10 data cable to the yellow wire on the CCU/ECU interconnect cable, and connect the black wire on the
GHC 10 data cable to CCU ground (page 11).
Connect the GHC 10 and the CCU to a NMEA 2000 network (page 12).
Connect any optional NMEA 2000-compatible devices to the NMEA 2000 network (page 14), or connect any optional NMEA 0183-compatible
devices to the GHC 10 if a NMEA 2000-compatible GPS device is not available (page 14).
Connect the ECU to the boat battery (page 10).
Configure the GHP 10 system by completing the Dockside Wizard and the Sea Trial Wizard (page 14).
Test and adjust the autopilot configuration.

GHP 10 Installation Instructions

© 2011 Garmin Ltd. or its subsidiaries
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose
without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed
and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided
further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any
person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and supplemental information concerning the use and operation of this
and other Garmin products.
Garmin®, the Garmin logo, and GPSMAP® are registered trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GHP™, GHC™, myGarmin™, and Shadow Drive™
are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Mercury® Verado® is a registered trademark of the Brunswick
Corporation. NMEA 2000® is a registered trademark of the National Marine Electronics Association. Loctite® and Pro Lock Tight® are registered trademarks of Henkel Corporation.

For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin Web site at www.garmin.com.

© 2011 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK
Garmin Corporation
No. 68, Zhangshu 2nd Road, Xizhi Dist., New Taipei City, 221, Taiwan (R.O.C.)
www.garmin.com
May 2011

190-01331-02 Rev. B

Printed in Taiwan

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract, Print high-res
Create Date                     : 2011:05:03 09:07:05-05:00
Creator                         : Adobe InDesign CS4 (6.0.5)
Modify Date                     : 2011:05:03 09:14:41-05:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2011:05:03 09:14:41-05:00
Creator Tool                    : Adobe InDesign CS4 (6.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8660 bytes, use -b option to extract)
Instance ID                     : uuid:9bb68733-7023-4fe2-a191-060abe56966b
Document ID                     : xmp.did:B2AD24A6D748E011A6DBF85D62A0565D
Original Document ID            : xmp.did:CEDE82A18F29E0118BF0823DBFAE3BC4
Rendition Class                 : proof:pdf
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:CEDE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:CFDE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:D0DE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:D1DE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:D2DE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:D3DE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:D4DE82A18F29E0118BF0823DBFAE3BC4, xmp.iid:FF1B039E262AE0119397E123E8B33299, xmp.iid:001C039E262AE0119397E123E8B33299, xmp.iid:79EB854C8B29E01197A78460B44485DA, xmp.iid:7AEB854C8B29E01197A78460B44485DA, xmp.iid:7BEB854C8B29E01197A78460B44485DA, xmp.iid:B0C773DD4C2AE01197A78460B44485DA, xmp.iid:B1C773DD4C2AE01197A78460B44485DA, xmp.iid:B2C773DD4C2AE01197A78460B44485DA, xmp.iid:B3C773DD4C2AE01197A78460B44485DA, xmp.iid:B4C773DD4C2AE01197A78460B44485DA, xmp.iid:B5C773DD4C2AE01197A78460B44485DA, xmp.iid:B6C773DD4C2AE01197A78460B44485DA, xmp.iid:B7C773DD4C2AE01197A78460B44485DA, xmp.iid:B8C773DD4C2AE01197A78460B44485DA, xmp.iid:B9C773DD4C2AE01197A78460B44485DA, xmp.iid:1FD32A32682AE01197A78460B44485DA, xmp.iid:20D32A32682AE01197A78460B44485DA, xmp.iid:21D32A32682AE01197A78460B44485DA, xmp.iid:22D32A32682AE01197A78460B44485DA, xmp.iid:23D32A32682AE01197A78460B44485DA, xmp.iid:24D32A32682AE01197A78460B44485DA, xmp.iid:25D32A32682AE01197A78460B44485DA, xmp.iid:26D32A32682AE01197A78460B44485DA, xmp.iid:27D32A32682AE01197A78460B44485DA, xmp.iid:28D32A32682AE01197A78460B44485DA, xmp.iid:29D32A32682AE01197A78460B44485DA, xmp.iid:495EF4F8022BE01197A78460B44485DA, xmp.iid:4A5EF4F8022BE01197A78460B44485DA, xmp.iid:4B5EF4F8022BE01197A78460B44485DA, xmp.iid:4C5EF4F8022BE01197A78460B44485DA, xmp.iid:4D5EF4F8022BE01197A78460B44485DA, xmp.iid:4E5EF4F8022BE01197A78460B44485DA, xmp.iid:4F5EF4F8022BE01197A78460B44485DA, xmp.iid:505EF4F8022BE01197A78460B44485DA, xmp.iid:515EF4F8022BE01197A78460B44485DA, xmp.iid:525EF4F8022BE01197A78460B44485DA, xmp.iid:C7A179604B2DE011843380736FE9D94A, xmp.iid:C8A179604B2DE011843380736FE9D94A, xmp.iid:C9A179604B2DE011843380736FE9D94A, xmp.iid:CAA179604B2DE011843380736FE9D94A, xmp.iid:CBA179604B2DE011843380736FE9D94A, xmp.iid:CCA179604B2DE011843380736FE9D94A, xmp.iid:CDA179604B2DE011843380736FE9D94A, xmp.iid:CEA179604B2DE011843380736FE9D94A, xmp.iid:CFA179604B2DE011843380736FE9D94A, xmp.iid:D0A179604B2DE011843380736FE9D94A, xmp.iid:E7CF5A3C692DE011843380736FE9D94A, xmp.iid:E8CF5A3C692DE011843380736FE9D94A, xmp.iid:EACF5A3C692DE011843380736FE9D94A, xmp.iid:EBCF5A3C692DE011843380736FE9D94A, xmp.iid:EECF5A3C692DE011843380736FE9D94A, xmp.iid:EFCF5A3C692DE011843380736FE9D94A, xmp.iid:F0CF5A3C692DE011843380736FE9D94A, xmp.iid:F1CF5A3C692DE011843380736FE9D94A, xmp.iid:BF1D68F37B2DE011843380736FE9D94A, xmp.iid:C01D68F37B2DE011843380736FE9D94A, xmp.iid:C11D68F37B2DE011843380736FE9D94A, xmp.iid:C21D68F37B2DE011843380736FE9D94A, xmp.iid:C31D68F37B2DE011843380736FE9D94A, xmp.iid:C41D68F37B2DE011843380736FE9D94A, xmp.iid:C51D68F37B2DE011843380736FE9D94A, xmp.iid:C61D68F37B2DE011843380736FE9D94A, xmp.iid:C71D68F37B2DE011843380736FE9D94A, xmp.iid:C81D68F37B2DE011843380736FE9D94A, xmp.iid:C91D68F37B2DE011843380736FE9D94A, xmp.iid:9B59F9468B2DE011843380736FE9D94A, xmp.iid:9C59F9468B2DE011843380736FE9D94A, xmp.iid:71AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:72AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:73AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:74AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:75AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:76AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:77AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:78AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:79AD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:7AAD3DFA122EE0119B21A1A4C70DCB47, xmp.iid:CE23AA46212EE0119B21A1A4C70DCB47, xmp.iid:CF23AA46212EE0119B21A1A4C70DCB47, xmp.iid:D023AA46212EE0119B21A1A4C70DCB47, xmp.iid:D123AA46212EE0119B21A1A4C70DCB47, xmp.iid:D223AA46212EE0119B21A1A4C70DCB47, xmp.iid:D323AA46212EE0119B21A1A4C70DCB47, xmp.iid:D423AA46212EE0119B21A1A4C70DCB47, xmp.iid:D523AA46212EE0119B21A1A4C70DCB47, xmp.iid:D623AA46212EE0119B21A1A4C70DCB47, xmp.iid:E800B816382EE0118F01E31E7188A1B9, xmp.iid:E900B816382EE0118F01E31E7188A1B9, xmp.iid:EA00B816382EE0118F01E31E7188A1B9, xmp.iid:EB00B816382EE0118F01E31E7188A1B9, xmp.iid:EC00B816382EE0118F01E31E7188A1B9, xmp.iid:ED00B816382EE0118F01E31E7188A1B9, xmp.iid:EE00B816382EE0118F01E31E7188A1B9, xmp.iid:EF00B816382EE0118F01E31E7188A1B9, xmp.iid:F000B816382EE0118F01E31E7188A1B9, xmp.iid:F100B816382EE0118F01E31E7188A1B9, xmp.iid:8129EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8229EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8329EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8429EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8529EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8629EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8729EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8829EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8929EAD53F2EE0118F01E31E7188A1B9, xmp.iid:8A29EAD53F2EE0118F01E31E7188A1B9, xmp.iid:EF6BF3B6142FE011B8879BC6DD9AF2A8, xmp.iid:796160CD7130E011B8879BC6DD9AF2A8, xmp.iid:54C93A80DC32E011B8879BC6DD9AF2A8, xmp.iid:72573D0DF232E011B8879BC6DD9AF2A8, xmp.iid:73573D0DF232E011B8879BC6DD9AF2A8, xmp.iid:79573D0DF232E011B8879BC6DD9AF2A8, xmp.iid:C725A7ADF732E011B8879BC6DD9AF2A8, xmp.iid:FB07E7B0FF32E011B8879BC6DD9AF2A8, xmp.iid:FC07E7B0FF32E011B8879BC6DD9AF2A8, xmp.iid:FD07E7B0FF32E011B8879BC6DD9AF2A8, xmp.iid:BC2396409233E011B8879BC6DD9AF2A8, xmp.iid:BD2396409233E011B8879BC6DD9AF2A8, xmp.iid:BE2396409233E011B8879BC6DD9AF2A8, xmp.iid:BF2396409233E011B8879BC6DD9AF2A8, xmp.iid:C02396409233E011B8879BC6DD9AF2A8, xmp.iid:C12396409233E011B8879BC6DD9AF2A8, xmp.iid:C22396409233E011B8879BC6DD9AF2A8, xmp.iid:4B6C0DACA233E011B8879BC6DD9AF2A8, xmp.iid:4E6C0DACA233E011B8879BC6DD9AF2A8, xmp.iid:E17C9F6C8834E011B8879BC6DD9AF2A8, xmp.iid:E27C9F6C8834E011B8879BC6DD9AF2A8, xmp.iid:E37C9F6C8834E011B8879BC6DD9AF2A8, xmp.iid:86674F723735E011B8879BC6DD9AF2A8, xmp.iid:87674F723735E011B8879BC6DD9AF2A8, xmp.iid:89674F723735E011B8879BC6DD9AF2A8, xmp.iid:8A674F723735E011B8879BC6DD9AF2A8, xmp.iid:8B674F723735E011B8879BC6DD9AF2A8, xmp.iid:8C674F723735E011B8879BC6DD9AF2A8, xmp.iid:8D674F723735E011B8879BC6DD9AF2A8, xmp.iid:8F674F723735E011B8879BC6DD9AF2A8, xmp.iid:408D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:438D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:458D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:468D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:478D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:488D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:498D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:4A8D594C4C35E011B8879BC6DD9AF2A8, xmp.iid:2428BB806235E011B8879BC6DD9AF2A8, xmp.iid:2528BB806235E011B8879BC6DD9AF2A8, xmp.iid:2628BB806235E011B8879BC6DD9AF2A8, xmp.iid:2728BB806235E011B8879BC6DD9AF2A8, xmp.iid:2828BB806235E011B8879BC6DD9AF2A8, xmp.iid:2A28BB806235E011B8879BC6DD9AF2A8, xmp.iid:2B28BB806235E011B8879BC6DD9AF2A8, xmp.iid:2C28BB806235E011B8879BC6DD9AF2A8, xmp.iid:2D28BB806235E011B8879BC6DD9AF2A8, xmp.iid:2E28BB806235E011B8879BC6DD9AF2A8, xmp.iid:0331F1B60836E011B8879BC6DD9AF2A8, xmp.iid:0431F1B60836E011B8879BC6DD9AF2A8, xmp.iid:0531F1B60836E011B8879BC6DD9AF2A8, xmp.iid:0631F1B60836E011B8879BC6DD9AF2A8, xmp.iid:0A31F1B60836E011B8879BC6DD9AF2A8, xmp.iid:0B31F1B60836E011B8879BC6DD9AF2A8, xmp.iid:E36248041636E011B8879BC6DD9AF2A8, xmp.iid:E46248041636E011B8879BC6DD9AF2A8, xmp.iid:E56248041636E011B8879BC6DD9AF2A8, xmp.iid:E96248041636E011B8879BC6DD9AF2A8, xmp.iid:EA6248041636E011B8879BC6DD9AF2A8, xmp.iid:EC6248041636E011B8879BC6DD9AF2A8, xmp.iid:ED6248041636E011B8879BC6DD9AF2A8, xmp.iid:4951698F2036E011B8879BC6DD9AF2A8, xmp.iid:4A51698F2036E011B8879BC6DD9AF2A8, xmp.iid:4B51698F2036E011B8879BC6DD9AF2A8, xmp.iid:9967413A4438E011B97FCB79A79A5B06, xmp.iid:E45020BC4139E0118714E5C7E05FA241, xmp.iid:C5305033DF39E0118714E5C7E05FA241, xmp.iid:C6305033DF39E0118714E5C7E05FA241, xmp.iid:F6105D6BAC3AE011B6AACC231B2C42CD, xmp.iid:628B1A60D73AE011B6AACC231B2C42CD, xmp.iid:638B1A60D73AE011B6AACC231B2C42CD, xmp.iid:648B1A60D73AE011B6AACC231B2C42CD, xmp.iid:668B1A60D73AE011B6AACC231B2C42CD, xmp.iid:688B1A60D73AE011B6AACC231B2C42CD, xmp.iid:698B1A60D73AE011B6AACC231B2C42CD, xmp.iid:6A8B1A60D73AE011B6AACC231B2C42CD, xmp.iid:6B8B1A60D73AE011B6AACC231B2C42CD, xmp.iid:3F6950EFE53AE011B6AACC231B2C42CD, xmp.iid:416950EFE53AE011B6AACC231B2C42CD, xmp.iid:426950EFE53AE011B6AACC231B2C42CD, xmp.iid:456950EFE53AE011B6AACC231B2C42CD, xmp.iid:466950EFE53AE011B6AACC231B2C42CD, xmp.iid:486950EFE53AE011B6AACC231B2C42CD, xmp.iid:496950EFE53AE011B6AACC231B2C42CD, xmp.iid:458C0F68833BE011B6AACC231B2C42CD, xmp.iid:4B8C0F68833BE011B6AACC231B2C42CD, xmp.iid:4C8C0F68833BE011B6AACC231B2C42CD, xmp.iid:4E8C0F68833BE011B6AACC231B2C42CD, xmp.iid:FADE986B9F3BE011B6AACC231B2C42CD, xmp.iid:FBDE986B9F3BE011B6AACC231B2C42CD, xmp.iid:FCDE986B9F3BE011B6AACC231B2C42CD, xmp.iid:FDDE986B9F3BE011B6AACC231B2C42CD, xmp.iid:01DF986B9F3BE011B6AACC231B2C42CD, xmp.iid:02DF986B9F3BE011B6AACC231B2C42CD, xmp.iid:03DF986B9F3BE011B6AACC231B2C42CD, xmp.iid:04DF986B9F3BE011B6AACC231B2C42CD, xmp.iid:3F4CA698D93DE011B6AACC231B2C42CD, xmp.iid:414CA698D93DE011B6AACC231B2C42CD, xmp.iid:424CA698D93DE011B6AACC231B2C42CD, xmp.iid:434CA698D93DE011B6AACC231B2C42CD, xmp.iid:444CA698D93DE011B6AACC231B2C42CD, xmp.iid:A82A059EF73DE011B6AACC231B2C42CD, xmp.iid:A92A059EF73DE011B6AACC231B2C42CD, xmp.iid:AA2A059EF73DE011B6AACC231B2C42CD, xmp.iid:AB2A059EF73DE011B6AACC231B2C42CD, xmp.iid:AC2A059EF73DE011B6AACC231B2C42CD, xmp.iid:AD2A059EF73DE011B6AACC231B2C42CD, xmp.iid:AE2A059EF73DE011B6AACC231B2C42CD, xmp.iid:AF2A059EF73DE011B6AACC231B2C42CD, xmp.iid:B02A059EF73DE011B6AACC231B2C42CD, xmp.iid:B12A059EF73DE011B6AACC231B2C42CD, xmp.iid:CA7350C3C33EE011B6AACC231B2C42CD, xmp.iid:CB7350C3C33EE011B6AACC231B2C42CD, xmp.iid:CC7350C3C33EE011B6AACC231B2C42CD, xmp.iid:CD7350C3C33EE011B6AACC231B2C42CD, xmp.iid:CE7350C3C33EE011B6AACC231B2C42CD, xmp.iid:CF7350C3C33EE011B6AACC231B2C42CD, xmp.iid:D07350C3C33EE011B6AACC231B2C42CD, xmp.iid:D17350C3C33EE011B6AACC231B2C42CD, xmp.iid:D27350C3C33EE011B6AACC231B2C42CD, xmp.iid:D37350C3C33EE011B6AACC231B2C42CD, xmp.iid:D47350C3C33EE011B6AACC231B2C42CD, xmp.iid:7C64F84A733FE011B6AACC231B2C42CD, xmp.iid:7D64F84A733FE011B6AACC231B2C42CD, xmp.iid:7E64F84A733FE011B6AACC231B2C42CD, xmp.iid:7F64F84A733FE011B6AACC231B2C42CD, xmp.iid:8064F84A733FE011B6AACC231B2C42CD, xmp.iid:8164F84A733FE011B6AACC231B2C42CD, xmp.iid:8264F84A733FE011B6AACC231B2C42CD, xmp.iid:8364F84A733FE011B6AACC231B2C42CD, xmp.iid:DCC230003B40E0118D78FBA2C7548016, xmp.iid:DDC230003B40E0118D78FBA2C7548016, xmp.iid:DEC230003B40E0118D78FBA2C7548016, xmp.iid:6D7DE6584940E0118D78FBA2C7548016, xmp.iid:6E7DE6584940E0118D78FBA2C7548016, xmp.iid:6F7DE6584940E0118D78FBA2C7548016, xmp.iid:707DE6584940E0118D78FBA2C7548016, xmp.iid:717DE6584940E0118D78FBA2C7548016, xmp.iid:727DE6584940E0118D78FBA2C7548016, xmp.iid:737DE6584940E0118D78FBA2C7548016, xmp.iid:747DE6584940E0118D78FBA2C7548016, xmp.iid:757DE6584940E0118D78FBA2C7548016, xmp.iid:767DE6584940E0118D78FBA2C7548016, xmp.iid:A05D448E6540E0118D78FBA2C7548016, xmp.iid:A25D448E6540E0118D78FBA2C7548016, xmp.iid:A35D448E6540E0118D78FBA2C7548016, xmp.iid:A45D448E6540E0118D78FBA2C7548016, xmp.iid:A55D448E6540E0118D78FBA2C7548016, xmp.iid:A65D448E6540E0118D78FBA2C7548016, xmp.iid:A75D448E6540E0118D78FBA2C7548016, xmp.iid:A85D448E6540E0118D78FBA2C7548016, xmp.iid:A95D448E6540E0118D78FBA2C7548016, xmp.iid:AA5D448E6540E0118D78FBA2C7548016, xmp.iid:09E12591F240E0118D78FBA2C7548016, xmp.iid:0BE12591F240E0118D78FBA2C7548016, xmp.iid:949C806F0741E011A6DBF85D62A0565D, xmp.iid:9A9C806F0741E011A6DBF85D62A0565D, xmp.iid:9B9C806F0741E011A6DBF85D62A0565D, xmp.iid:9C9C806F0741E011A6DBF85D62A0565D, xmp.iid:9D9C806F0741E011A6DBF85D62A0565D, xmp.iid:14B7B9BA3041E011A6DBF85D62A0565D, xmp.iid:15B7B9BA3041E011A6DBF85D62A0565D, xmp.iid:16B7B9BA3041E011A6DBF85D62A0565D, xmp.iid:17B7B9BA3041E011A6DBF85D62A0565D, xmp.iid:18B7B9BA3041E011A6DBF85D62A0565D, xmp.iid:19B7B9BA3041E011A6DBF85D62A0565D, xmp.iid:1AB7B9BA3041E011A6DBF85D62A0565D, xmp.iid:1BB7B9BA3041E011A6DBF85D62A0565D, xmp.iid:1CB7B9BA3041E011A6DBF85D62A0565D, xmp.iid:1DB7B9BA3041E011A6DBF85D62A0565D, xmp.iid:1EB7B9BA3041E011A6DBF85D62A0565D, xmp.iid:321FCF225B43E011A6DBF85D62A0565D, xmp.iid:331FCF225B43E011A6DBF85D62A0565D, xmp.iid:341FCF225B43E011A6DBF85D62A0565D, xmp.iid:351FCF225B43E011A6DBF85D62A0565D, xmp.iid:361FCF225B43E011A6DBF85D62A0565D, xmp.iid:3B1FCF225B43E011A6DBF85D62A0565D, xmp.iid:4BA263AA8043E011A6DBF85D62A0565D, xmp.iid:50A263AA8043E011A6DBF85D62A0565D, xmp.iid:53A263AA8043E011A6DBF85D62A0565D, xmp.iid:465144422244E011A6DBF85D62A0565D, xmp.iid:475144422244E011A6DBF85D62A0565D, xmp.iid:4E5144422244E011A6DBF85D62A0565D, xmp.iid:505144422244E011A6DBF85D62A0565D, xmp.iid:0BE99D48DF44E011A6DBF85D62A0565D, xmp.iid:0CE99D48DF44E011A6DBF85D62A0565D, xmp.iid:0DE99D48DF44E011A6DBF85D62A0565D, xmp.iid:0EE99D48DF44E011A6DBF85D62A0565D, xmp.iid:10E99D48DF44E011A6DBF85D62A0565D, xmp.iid:15E99D48DF44E011A6DBF85D62A0565D, xmp.iid:B2E9A245F444E011A6DBF85D62A0565D, xmp.iid:9E79095E0645E011A6DBF85D62A0565D, xmp.iid:568C25541045E011A6DBF85D62A0565D, xmp.iid:588C25541045E011A6DBF85D62A0565D, xmp.iid:598C25541045E011A6DBF85D62A0565D, xmp.iid:5B8C25541045E011A6DBF85D62A0565D, xmp.iid:5E8C25541045E011A6DBF85D62A0565D, xmp.iid:141901BBD445E011A6DBF85D62A0565D, xmp.iid:151901BBD445E011A6DBF85D62A0565D, xmp.iid:171901BBD445E011A6DBF85D62A0565D, xmp.iid:191901BBD445E011A6DBF85D62A0565D, xmp.iid:1A1901BBD445E011A6DBF85D62A0565D, xmp.iid:1C1901BBD445E011A6DBF85D62A0565D, xmp.iid:ED417943CC48E011A6DBF85D62A0565D, xmp.iid:EE417943CC48E011A6DBF85D62A0565D, xmp.iid:EF417943CC48E011A6DBF85D62A0565D, xmp.iid:F0417943CC48E011A6DBF85D62A0565D, xmp.iid:F1417943CC48E011A6DBF85D62A0565D, xmp.iid:F2417943CC48E011A6DBF85D62A0565D, xmp.iid:F3417943CC48E011A6DBF85D62A0565D, xmp.iid:F4417943CC48E011A6DBF85D62A0565D, xmp.iid:F5417943CC48E011A6DBF85D62A0565D, xmp.iid:F6417943CC48E011A6DBF85D62A0565D, xmp.iid:F7417943CC48E011A6DBF85D62A0565D, xmp.iid:ACAD24A6D748E011A6DBF85D62A0565D, xmp.iid:ADAD24A6D748E011A6DBF85D62A0565D, xmp.iid:AFAD24A6D748E011A6DBF85D62A0565D, xmp.iid:B0AD24A6D748E011A6DBF85D62A0565D, xmp.iid:B1AD24A6D748E011A6DBF85D62A0565D, xmp.iid:B2AD24A6D748E011A6DBF85D62A0565D, xmp.iid:50D3A51AED61E0118534DA6229037472, xmp.iid:51D3A51AED61E0118534DA6229037472, xmp.iid:C40A60884964E0119593E7A9F9FF3D5B, xmp.iid:FEE5E4835A72E011B4E6FFB92FC803BB, xmp.iid:59D95BEB7972E011930AB7BA5D16C706, xmp.iid:5AD95BEB7972E011930AB7BA5D16C706, xmp.iid:5BD95BEB7972E011930AB7BA5D16C706
History When                    : 2011:01:26 15:02:48-06:00, 2011:01:26 15:09:27-06:00, 2011:01:26 15:09:27-06:00, 2011:01:26 15:10:49-06:00, 2011:01:26 15:10:49-06:00, 2011:01:26 15:12:10-06:00, 2011:01:26 15:12:10-06:00, 2011:01:27 10:01:59-06:00, 2011:01:27 10:01:59-06:00, 2011:01:27 11:11:47-06:00, 2011:01:27 11:11:47-06:00, 2011:01:27 13:26:31-06:00, 2011:01:27 13:37:32-06:00, 2011:01:27 14:03:45-06:00, 2011:01:27 14:37:46-06:00, 2011:01:27 14:43:55-06:00, 2011:01:27 14:47:04-06:00, 2011:01:27 14:52:05-06:00, 2011:01:27 15:36:51-06:00, 2011:01:27 15:53:01-06:00, 2011:01:27 16:07:21-06:00, 2011:01:27 16:11:07-06:00, 2011:01:27 16:53:02-06:00, 2011:01:27 16:59:31-06:00, 2011:01:28 08:58:36-06:00, 2011:01:28 09:00:58-06:00, 2011:01:28 09:33:53-06:00, 2011:01:28 09:44:31-06:00, 2011:01:28 09:47:20-06:00, 2011:01:28 09:51:58-06:00, 2011:01:28 09:58:25-06:00, 2011:01:28 11:14:49-06:00, 2011:01:28 11:20:17-06:00, 2011:01:28 11:20:58-06:00, 2011:01:28 11:24:43-06:00, 2011:01:28 13:13:36-06:00, 2011:01:28 13:24:56-06:00, 2011:01:28 13:25:17-06:00, 2011:01:28 14:17:21-06:00, 2011:01:28 14:30:15-06:00, 2011:01:28 14:35:01-06:00, 2011:01:28 16:32:40-06:00, 2011:01:28 16:56:10-06:00, 2011:01:31 09:04:18-06:00, 2011:01:31 10:11:22-06:00, 2011:01:31 10:56:40-06:00, 2011:01:31 11:08:17-06:00, 2011:01:31 11:09:45-06:00, 2011:01:31 11:10:08-06:00, 2011:01:31 11:21:50-06:00, 2011:01:31 11:42:31-06:00, 2011:01:31 11:49:24-06:00, 2011:01:31 12:35-06:00, 2011:01:31 12:38:02-06:00, 2011:01:31 12:50:15-06:00, 2011:01:31 13:23:14-06:00, 2011:01:31 13:25:17-06:00, 2011:01:31 13:54:44-06:00, 2011:01:31 14:11:24-06:00, 2011:01:31 14:13:26-06:00, 2011:01:31 14:46:14-06:00, 2011:01:31 14:52-06:00, 2011:01:31 14:54:18-06:00, 2011:01:31 14:54:31-06:00, 2011:01:31 14:55:01-06:00, 2011:01:31 14:56:08-06:00, 2011:01:31 15:44:39-06:00, 2011:01:31 15:44:58-06:00, 2011:01:31 15:48:47-06:00, 2011:01:31 16:00:24-06:00, 2011:01:31 16:19:54-06:00, 2011:01:31 16:41:09-06:00, 2011:01:31 16:41:43-06:00, 2011:01:31 16:46:56-06:00, 2011:02:01 08:53:06-06:00, 2011:02:01 09:00:53-06:00, 2011:02:01 09:10:01-06:00, 2011:02:01 09:21:24-06:00, 2011:02:01 09:48:06-06:00, 2011:02:01 09:50:14-06:00, 2011:02:01 10:12:01-06:00, 2011:02:01 10:14:55-06:00, 2011:02:01 10:24:06-06:00, 2011:02:01 10:28:09-06:00, 2011:02:01 10:35:27-06:00, 2011:02:01 10:46:58-06:00, 2011:02:01 11:02:23-06:00, 2011:02:01 11:32:34-06:00, 2011:02:01 11:40:13-06:00, 2011:02:01 11:48:52-06:00, 2011:02:01 11:55:52-06:00, 2011:02:01 11:58:51-06:00, 2011:02:01 12:53:32-06:00, 2011:02:01 13:18:45-06:00, 2011:02:01 13:21:14-06:00, 2011:02:01 13:24:33-06:00, 2011:02:01 13:34:20-06:00, 2011:02:01 13:42:50-06:00, 2011:02:01 13:47:38-06:00, 2011:02:01 13:57:11-06:00, 2011:02:01 14:02:42-06:00, 2011:02:01 14:03:46-06:00, 2011:02:01 14:08:16-06:00, 2011:02:01 14:14:12-06:00, 2011:02:01 14:15:05-06:00, 2011:02:01 14:26:13-06:00, 2011:02:01 14:38:12-06:00, 2011:02:01 14:45-06:00, 2011:02:01 14:48:57-06:00, 2011:02:01 14:53:17-06:00, 2011:02:01 14:55:58-06:00, 2011:02:01 15:04:57-06:00, 2011:02:01 15:08:47-06:00, 2011:02:03 09:50:56-06:00, 2011:02:04 11:26:12-06:00, 2011:02:07 11:24:43-06:00, 2011:02:07 13:41:26-06:00, 2011:02:07 13:47:24-06:00, 2011:02:07 14:13:53-06:00, 2011:02:07 14:39:29-06:00, 2011:02:08 08:42:29-06:00, 2011:02:08 08:45:23-06:00, 2011:02:08 08:46:46-06:00, 2011:02:08 08:46:46-06:00, 2011:02:08 08:48:14-06:00, 2011:02:08 08:56:50-06:00, 2011:02:08 09:01:38-06:00, 2011:02:08 09:13:38-06:00, 2011:02:08 09:19:52-06:00, 2011:02:08 09:22:08-06:00, 2011:02:08 10:46:40-06:00, 2011:02:08 14:19:21-06:00, 2011:02:10 10:11:19-06:00, 2011:02:10 10:20:35-06:00, 2011:02:10 10:48:51-06:00, 2011:02:10 11:01:47-06:00, 2011:02:10 11:04:12-06:00, 2011:02:10 11:20:02-06:00, 2011:02:10 11:21:58-06:00, 2011:02:10 11:51:11-06:00, 2011:02:10 12:00:57-06:00, 2011:02:10 13:04:58-06:00, 2011:02:10 13:14:51-06:00, 2011:02:10 13:31:03-06:00, 2011:02:10 14:20:52-06:00, 2011:02:10 14:31:15-06:00, 2011:02:10 14:37:21-06:00, 2011:02:10 14:38:25-06:00, 2011:02:10 14:52:28-06:00, 2011:02:10 15:07:46-06:00, 2011:02:10 15:25:13-06:00, 2011:02:10 16:10-06:00, 2011:02:10 16:20:43-06:00, 2011:02:10 16:27:35-06:00, 2011:02:10 16:59:18-06:00, 2011:02:10 16:59:41-06:00, 2011:02:11 09:10:33-06:00, 2011:02:11 09:17:29-06:00, 2011:02:11 09:28:23-06:00, 2011:02:11 09:33-06:00, 2011:02:11 11:22:47-06:00, 2011:02:11 11:59:47-06:00, 2011:02:11 13:02:11-06:00, 2011:02:11 13:06:50-06:00, 2011:02:11 13:08:33-06:00, 2011:02:11 13:21:36-06:00, 2011:02:11 13:22:16-06:00, 2011:02:11 13:35:01-06:00, 2011:02:11 13:46:45-06:00, 2011:02:11 13:47:01-06:00, 2011:02:11 13:59:33-06:00, 2011:02:11 14:01:28-06:00, 2011:02:11 14:15:42-06:00, 2011:02:11 14:47:48-06:00, 2011:02:11 15:13:39-06:00, 2011:02:11 15:16:59-06:00, 2011:02:11 16:49:25-06:00, 2011:02:14 14:43:40-06:00, 2011:02:15 16:59:39-06:00, 2011:02:16 10:08:06-06:00, 2011:02:16 10:13:53-06:00, 2011:02:17 14:18:32-06:00, 2011:02:17 14:49:12-06:00, 2011:02:17 15:18:42-06:00, 2011:02:17 15:45:22-06:00, 2011:02:17 16:00:48-06:00, 2011:02:17 16:02:21-06:00, 2011:02:17 16:06:04-06:00, 2011:02:17 16:22:10-06:00, 2011:02:17 16:25:45-06:00, 2011:02:17 16:33:25-06:00, 2011:02:17 16:36:01-06:00, 2011:02:17 16:37:46-06:00, 2011:02:17 16:41:10-06:00, 2011:02:18 08:17:52-06:00, 2011:02:18 08:25:20-06:00, 2011:02:18 09:34:51-06:00, 2011:02:18 11:29:16-06:00, 2011:02:18 14:20:57-06:00, 2011:02:18 14:26:45-06:00, 2011:02:18 14:28:47-06:00, 2011:02:18 14:41:11-06:00, 2011:02:18 14:42:29-06:00, 2011:02:18 14:44:07-06:00, 2011:02:18 14:52:15-06:00, 2011:02:18 16:45:12-06:00, 2011:02:18 16:46:09-06:00, 2011:02:21 10:18:33-06:00, 2011:02:21 10:32:11-06:00, 2011:02:21 10:42:39-06:00, 2011:02:21 11:44:52-06:00, 2011:02:21 13:10:05-06:00, 2011:02:21 13:27:58-06:00, 2011:02:21 13:28:53-06:00, 2011:02:21 15:05:04-06:00, 2011:02:22 08:34:19-06:00, 2011:02:22 08:52:07-06:00, 2011:02:22 09:48:25-06:00, 2011:02:22 09:52:23-06:00, 2011:02:22 10:32:31-06:00, 2011:02:22 11:04:17-06:00, 2011:02:22 11:43:29-06:00, 2011:02:22 12:57:18-06:00, 2011:02:22 13:25:37-06:00, 2011:02:22 14:38:53-06:00, 2011:02:22 16:02:23-06:00, 2011:02:22 16:30:10-06:00, 2011:02:22 16:41:25-06:00, 2011:02:22 16:47:57-06:00, 2011:02:23 09:46:40-06:00, 2011:02:23 09:54:23-06:00, 2011:02:23 10:14:58-06:00, 2011:02:23 10:26:50-06:00, 2011:02:23 11:14:12-06:00, 2011:02:23 11:20:37-06:00, 2011:02:23 11:35:23-06:00, 2011:02:23 13:15:20-06:00, 2011:02:23 13:33:34-06:00, 2011:02:23 13:36:25-06:00, 2011:02:23 13:46:39-06:00, 2011:02:23 13:57:19-06:00, 2011:02:23 13:59:29-06:00, 2011:02:23 14:03:57-06:00, 2011:02:24 12:39:04-06:00, 2011:02:24 13:01:33-06:00, 2011:02:24 13:05:48-06:00, 2011:02:24 13:17:16-06:00, 2011:02:24 13:32:01-06:00, 2011:02:24 13:49:49-06:00, 2011:02:24 13:52:34-06:00, 2011:02:24 13:56:32-06:00, 2011:02:24 14:58:38-06:00, 2011:02:24 15:03:06-06:00, 2011:02:24 15:10:21-06:00, 2011:02:24 16:18:49-06:00, 2011:02:24 16:25:43-06:00, 2011:02:24 16:29:34-06:00, 2011:02:24 16:37:34-06:00, 2011:02:24 16:41:07-06:00, 2011:02:24 16:48:01-06:00, 2011:02:25 08:00:28-06:00, 2011:02:25 08:01:41-06:00, 2011:02:25 08:38:22-06:00, 2011:02:25 08:58:39-06:00, 2011:02:25 09:16:49-06:00, 2011:02:25 09:18:43-06:00, 2011:02:25 09:18:58-06:00, 2011:02:25 09:55:02-06:00, 2011:02:25 11:48:21-06:00, 2011:02:25 16:11:07-06:00, 2011:02:25 16:19:10-06:00, 2011:02:25 16:25:29-06:00, 2011:02:25 16:30:23-06:00, 2011:02:25 16:43:56-06:00, 2011:02:25 16:48:56-06:00, 2011:02:28 08:32:25-06:00, 2011:02:28 08:50:58-06:00, 2011:02:28 08:58:02-06:00, 2011:02:28 09:26:18-06:00, 2011:02:28 09:28:32-06:00, 2011:02:28 10:02:10-06:00, 2011:02:28 10:04:05-06:00, 2011:02:28 10:13:58-06:00, 2011:02:28 10:21:25-06:00, 2011:02:28 10:52:32-06:00, 2011:02:28 10:54:59-06:00, 2011:02:28 10:58:10-06:00, 2011:02:28 11:09:04-06:00, 2011:02:28 13:08:59-06:00, 2011:02:28 14:46:22-06:00, 2011:02:28 15:21:11-06:00, 2011:03:01 08:56:58-06:00, 2011:03:01 10:06:22-06:00, 2011:03:01 10:37:55-06:00, 2011:03:01 11:07:14-06:00, 2011:03:01 16:26:28-06:00, 2011:03:02 08:54:19-06:00, 2011:03:02 09:11-06:00, 2011:03:02 09:13:17-06:00, 2011:03:02 09:16:14-06:00, 2011:03:02 09:22:42-06:00, 2011:03:02 09:57:45-06:00, 2011:03:02 11:19:37-06:00, 2011:03:02 13:20:17-06:00, 2011:03:02 14:19:02-06:00, 2011:03:02 15:02:05-06:00, 2011:03:02 15:08:25-06:00, 2011:03:03 09:25:02-06:00, 2011:03:03 10:53:30-06:00, 2011:03:03 12:52:42-06:00, 2011:03:04 09:21:46-06:00, 2011:03:04 11:31:36-06:00, 2011:03:04 11:33:41-06:00, 2011:03:04 13:13:38-06:00, 2011:03:04 14:12:17-06:00, 2011:03:07 08:51:16-06:00, 2011:03:07 09:04:56-06:00, 2011:03:07 09:12:01-06:00, 2011:03:07 09:18:25-06:00, 2011:03:07 09:20:55-06:00, 2011:03:07 09:25:57-06:00, 2011:03:07 09:53:56-06:00, 2011:03:07 09:55:35-06:00, 2011:03:07 09:57-06:00, 2011:03:07 09:57:45-06:00, 2011:03:07 10:04:50-06:00, 2011:03:07 10:12:52-06:00, 2011:03:07 10:26:26-06:00, 2011:03:07 10:29:16-06:00, 2011:03:07 10:42:50-06:00, 2011:03:07 10:42:59-06:00, 2011:03:07 10:43:22-06:00, 2011:03:07 10:43:22-06:00, 2011:04:08 09:33-05:00, 2011:04:08 09:38:11-05:00, 2011:04:11 09:39:40-05:00, 2011:04:29 09:02:12-05:00, 2011:05:03 08:57:20-05:00, 2011:05:03 09:06:26-05:00, 2011:05:03 09:06:30-05:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /metadata, /;/metadata, /metadata, /;/metadata, /, /metadata, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /;/metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /
Derived From Instance ID        : xmp.iid:B1AD24A6D748E011A6DBF85D62A0565D
Derived From Document ID        : xmp.did:BC2396409233E011B8879BC6DD9AF2A8
Derived From Original Document ID: xmp.did:CEDE82A18F29E0118BF0823DBFAE3BC4
Derived From Rendition Class    : default
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:BB25CA097255DD11B22F90F22C99F3D5, uuid:4ab9b30c-1a69-4c5a-9e72-7462d44b079e, uuid:ff7f945b-f337-4ea5-875b-bf0cd7df0f23, uuid:99b24a62-e740-4ee7-a2ec-1a0ed7805720, uuid:5cd202ac-9f31-4105-a649-105fb9eb8441, uuid:845fe744-f40c-4075-97ed-4d7c65d99aff, uuid:e6410d7f-da9b-4701-9561-7de04e35419b, uuid:96a6aa67-33e8-474f-a419-2b500e752fbd, uuid:a3010310-8ea1-4f2e-9a09-110bdbeae3f8, uuid:bb7df659-30c1-4438-b074-d4656ea9df7b, uuid:0688c8cb-4ced-4cca-9f33-54f8c28d1c58, uuid:73afdab2-f54e-42df-9f6b-2991dc483b21, uuid:2b09e43f-342e-43bb-a771-505aad6bc21f, uuid:866090f0-c901-40dc-97a6-20d8bd430c43, uuid:b3982d8a-d3e8-45bf-bb30-213408feaf8e, uuid:a7414193-602e-4edf-9960-6ec1bed2b0be, uuid:9f9dcd53-b82f-41b0-b85f-4e3862bdf130, uuid:b1c355c6-80ad-4092-b3d1-57ced693055f, uuid:ce780455-3a41-42cc-ac2a-d93f092b2ac0, uuid:81eccbbe-b68c-41a4-9385-2a15a6d66d79, uuid:2C685C2B420ADD11AC48F989BC8FF98B, uuid:c791d78d-c294-42b0-aa9c-c3324a73ccca, uuid:c791d78d-c294-42b0-aa9c-c3324a73ccca, uuid:da88a700-80ee-46f6-a135-f53935517732, uuid:86957363030BDD11AB6CCEB26A05387A, uuid:3a3fcaa9-cf2d-46a1-ba69-38d071151c5c, uuid:0f98e694-1329-4c48-a072-d9786263fc78, uuid:19f64601-62d5-4421-b54a-90f641cee376, uuid:252925b9-5dd1-407d-9949-614d758eb87d, uuid:eaf65b0a-5b8e-4772-b50b-00bd52b128fe, uuid:BB25CA097255DD11B22F90F22C99F3D5
Manifest Reference Document ID  : uuid:BA25CA097255DD11B22F90F22C99F3D5, uuid:C2CB221E05F5DC119107D052357E24FF, uuid:C4CB221E05F5DC119107D052357E24FF, uuid:4C6E62A3DCF5DC1184E8B85148CFEDA0, uuid:607C256C6CF4DC11812AA4E7C5C7C262, uuid:C6CB221E05F5DC119107D052357E24FF, uuid:FDCFB04798F6DC118ADBB7E3A4350DB1, uuid:C8CB221E05F5DC119107D052357E24FF, uuid:D37B97B9CDF5DC1184E8B85148CFEDA0, uuid:6B6D11D65586DC1189C49818A04F1B54, uuid:696D11D65586DC1189C49818A04F1B54, uuid:6DF85C6DC1F5DC11BE15D87EED573CFA, uuid:0F04C36D9993DC11855290FE929EC2CA, uuid:CF6F9090EC86DC118848E92939804024, uuid:CC6F9090EC86DC118848E92939804024, xmp.did:1C9D0143DA3AE011AB79E978778EDAD1, uuid:9BB638BC4D5EDD1190EC9B961C633D12, uuid:0D9920D4145FDD1181B0C0A34054BD20, uuid:1FC0909005F5DC119107D052357E24FF, uuid:1DC0909005F5DC119107D052357E24FF, uuid:2B685C2B420ADD11AC48F989BC8FF98B, xmp.did:9529CB178213E011BB30C7D6729F47DD, xmp.did:9529CB178213E011BB30C7D6729F47DD, uuid:CC6A70ACACFADC1189A6D7249CED6769, uuid:85957363030BDD11AB6CCEB26A05387A, xmp.did:F24C55D2B012E011950CFB9036575DA4, uuid:C393CC3891E9DE11BBA2BA274E66F6DB, uuid:D2FFE3D675F9DE11923AA600D92DDD11, uuid:C40EA7A880FADC11A05AF03F4AB03A56, uuid:C20EA7A880FADC11A05AF03F4AB03A56, uuid:BA25CA097255DD11B22F90F22C99F3D5
Doc Change Count                : 75855
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Layout                     : SinglePage
Page Mode                       : UseOutlines
Page Count                      : 26

EXIF Metadata provided by EXIF.tools

Garmin 296 M Ghp 10 Marine Autopilot System Manual Installation Instructions

Navigation menu

Versions of this User Manual:

Views

Navigation