Garmin 536 M Gsd 20 Manual Installation Guide 190 00255 00_0E
GSD-20 GSD20_InstallationGuide
GSD-20 to the manual e63480d2-068c-4fd2-8fa3-a038b7074966
2014-07-05
: Garmin 536-M-Gsd-20-Manual-Installation-Guide 536-m-gsd-20-manual-installation-guide garmin pdf
Open the PDF directly: View PDF .
Page Count: 12
GSD 20
Sounder
Module
installation instructions
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded, or stored in any
storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto
a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed
copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content
without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and
supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, DCG®, and See-Thru® are a registered trademark of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin.
Safety Information
WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
This Notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our Web
site at http://www.garmin.com/prop65.
Limited Warranty
This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its
sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor,
provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to installation errors, abuse, misuse, accident, or
unauthorized alteration or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR
STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING
FROM THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not allow the exclusion of
incidental or consequential damages, so the above limitations may not apply to you.
Garmin retains the exclusive right to repair or replace the product or offer a full refund of the purchase price at its sole discretion. SUCH REMEDY SHALL BE
YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.
Products sold through online auctions are not eligible for rebates or other special offers from Garmin. Online auction confirmations are not accepted for warranty
verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from
any package purchased through an online auction.
To obtain warranty service, contact your local Garmin authorized dealer or call Garmin Product Support for shipping instructions and an RMA tracking number. The
product should be securely packed with the tracking number clearly written on the outside of the package. The product should then be sent, freight charges prepaid, to
any Garmin warranty service station. A copy of the original sales receipt is required as the proof of purchase for warranty repairs.
July 2005 Part Number 190-00225-00 Rev. E Printed in Taiwan
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, U.S.A.
Tel. 913/397.8200 or 800/800.1020
Fax 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle,
Abbey Park Industrial Estate,
Romsey, SO51 9DL, U.K.
Tel. 44/0870.8501241
Fax 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
© Copyright 2004, 2005 Garmin Ltd. or its subsidiaries
1GSD 20 Sonar Module
INTRODUCTION
Thank you for choosing the Garmin GSD 20. The GSD 20 is an intelligent, remote sounder module designed to include powerful features
as found in other Garmin sounders, including Depth Control Gain (DCG®) and See-Thru® technology. When used with compatible Garmin
chartplotters, it provides full-featured depth sounder functions. It may interface to multiple head units, providing for complete sounder control
from multiple stations, including transmit frequency, range, and gain adjustments. To get successful results from your GSD 20, take time to read
through this installation guide. If any items are missing, please contact your Garmin dealer immediately.
Included Equipment:
• GSD 20 Sounder Module
• 30’ (9.1 m) Power/Data Cable
• Installation Guide for the GSD 20
Optional Transducers
The transducer acts as the eyes and ears of your new sonar. The transducer transmits sound waves toward the bottom in a cone shape. The larger
the cone angle, the larger the coverage area at a given depth.
Proper transducer selection and installation are critical to the operation of your unit. Since mounting locations vary, see your local dealer or
contact Garmin Product Support for further information. A full list of transducers can be found at www.garmin.com.
INTRODUCTION
Power/Data
Connector
LED Status Indicator
Transducer
Connector
Mounting Holes
2
GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
The GSD 20 must be properly installed according to the following instructions to get the best possible performance. To complete the
installation, you need the appropriate fasteners. If you experience difficulty with the installation, contact Garmin Product Support.
The module should be mounted in an out-of-the-way location that is dry and well ventilated. Avoid mounting the module where it can be
submerged in liquids or exposed to extreme temperatures. Be sure to mount the module so that the LED is visible.
To install the GSD 20 module:
1. Once the location is chosen, place the unit. Be sure to allow enough clearance for attaching the cables. Using the module as a template,
mark the location of the four mounting holes. If needed, additional mounting holes may be drilled in the side mounting flanges of the
module.
2. Attach the GSD 20 to the mounting location using the appropriate fasteners.
3. Mount the transducer according to the instructions provided with the transducer.
4. Route the cables to the mounting location of the display unit. Use the appropriate tie-wraps, fasteners, and sealant to secure the cable
along the route and through any bulkhead or deck.
5. Once the GSD 20 module has been installed, connect the power/data and transducer cables to the appropriate receptacle.
6. Refer to the following wiring diagrams for connecting the GSD 20 to compatible Garmin units.
NOTE: You can extend the wiring of the GSD 20 power/data cable up to 100’ (30 m) total length. Use 22 AWG, 4-conductor shielded cable for data
cable and 18 AWG for power. Transducer cable extensions are available through your Garmin dealer.
3GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
WIRE
COLOR
GARMIN GSD 20
SOUNDER MODULE
BLACK
ORANGE
RED
WHITE/BLUE
BLACK
RED
WHITE/BLUE
WHITE/BROWN WHITE/BROWN
WIRE
COLOR
5 A
FUSE
ORANGE
2 A
FUSE
TO
TRANSDUCER
BATTERY
10-35 VOLTS DC
BASIC WIRING FOR THE GARMIN GSD 20 TO A SINGLE
GPSMAP 2006/2006C/2010/2010C/3005C/3006C/3010C
Notes:
1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs over 30’ (9.1 m).
2. Refer to the GPSMAP 2006/2006C/2010/2010C/3005C/3006C/3010C Installation Instructions for wiring the GPS 17 sensor and other devices.
3. For runs over 30’ (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the end of the shield drain wire.
4. When multiple GPSMAP 3005C/3006C/3010C units are in use, only wire the GSD 20 to one unit. The GSD 20 information is transmitted to all
units connected to the Garmin Marnine Network.
4
GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
BATTERY
10-35 VOLTS DC
BASIC WIRING FOR THE GARMIN GSD 20 TO A DUAL GPSMAP 2006/2006C/2010/2010C
*This diagram does not apply to the GPSMAP 3005C/3006C/3010C. Refer to Note 4 on the Single GPSMAP
2006/2006C/2010/2010C/3005/C3006C/3010C diagram.
Notes:
1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs over 30’ (9.1 m).
2. Refer to the GPSMAP 2006/2006C/2010/2010C Installation Instructions for wiring the GPS 17 sensor and other devices.
3. For runs over 30’ (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the end of the shield drain wire.
4. Use unit #1 to update the GSD 20 software.
5GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
WIRE
COLOR
GARMIN GSD 20
SOUNDER MODULE
BLACK
ORANGE
RED
WHITE/BLUE
BLACK
RED
BLUE
YELLOW WHITE/BROWN
WIRE
COLOR
FUSE
1.5A
FUSE
2A
TO
TRANSDUCER
ON
OFF
SEE NOTE 3
OPTION 1
ON
OFF
SEE NOTE 3
OPTION 2
BATTERY
10-35 VOLTS DC
BASIC WIRING FOR THE GARMIN GSD 20 TO A SINGLE GPSMAP 276C/296/376C/396
Notes:
1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs
over 30’ (9.1 m).
2. For runs over 30’ (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the
end of the shield drain wire.
3. The Orange wire must be pulled low (-) in order for the GSD 20 to power on.
Option 1: If the GSD 20 is wired to a circuit that is switched on the Red (+) wire, connect the Orange wire to ground.
The GSD 20 and the GPSMAP 276C/296/376C/396 turn on/off when power is applied/removed to the Red wire.
Option 2: If the Red (+) wire is applied directly to a power source, install a switch between the Orange wire and ground.
The GSD 20 turns on/off when ground is applied/removed to the Orange wire.
6
GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
BASIC WIRING FOR THE GARMIN GSD 20 TO A SINGLE GPSMAP 182/182C/192C/232
WIRE
COLOR
GARMIN GSD 20
SOUNDER MODULE
BLACK
ORANGE
RED
WHITE/BLUE
BLACK
RED
BLUE
BROWN WHITE/BROWN
WIRE
COLOR
FUSE
1.5A
FUSE
2A
TO
TRANSDUCER
ON
OFF
SEE NOTE 3
OPTION 1
BATTERY
10-35 VOLTS DC
ON
OFF
SEE NOTE 3
OPTION 2
Notes:
1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs over 30’ (9.1 m).
2. For runs over 30’ (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the end of the shield
drain wire.
3. The Orange wire must be pulled low (-) in order for the GSD 20 to power on.
Option 1: If the GSD 20 is wired to a circuit that is switched on the Red (+) wire, connect the Orange wire to ground. The GSD 20 and
the GPSMAP 182/182C/192C/232 turns on/off when power is applied/removed to the Red wire.
Option 2: If the Red (+) wire is applied directly to a power source, install a switch between the Orange wire and ground. The GSD 20
turns on or off when ground is applied or removed to the Orange wire.
7GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
WIRE
COLOR
GARMIN GSD 20
SOUNDER MODULE
BLACK
ORANGEORANGE
RED
WHITE/BLUE
BLACK
RED
BLUE
BROWN WHITE/BROWN
WIRE
COLOR
FUSE
5A
FUSE
2A
TO
TRANSDUCER
BATTERY
10-35 VOLTS DC
BASIC WIRING FOR THE GARMIN GSD 20 TO A SINGLE GPSMAP 172/172C
Notes:
1. Power and ground wires require 18 AWG. All other wires require 22 AWG. Use 4-conductor, shielded wiring for runs over 30’ (9.1 m).
2. Refer to the GPSMAP 172/172C Owner’s Manual for wiring the GPS 17 sensor and other devices.
3. For runs over 30’ (9.1 m), the drain wire must be connected to the shielding of the extension run. Do not terminate the end of the shield drain wire.
8
GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
Blink Codes
Once the unit is installed, it switches on when the display unit is powered on (or the GSD remote power line is pulled low, with power applied).
The two-color (Green/Red) LED on the GSD 20 indicates the current operational status of the module. Codes are:
Code Status
Green blinking, on for 1 second, off for 1/2 second (slow blink) GSD 20 is servicing one directly wired connection and the display
device is operating properly.
The user should see sonar data on the display unit.
Green blinking, on for 1/2 second, off for 1/4 second (fast blink) GSD 20 is servicing two dirctly wired connections and the two display
devices are operating properly.
The user should see sonar data on both display units.
Red blinking, on for 1 second, off for 1/2 second (slow blink) GSD 20 is powered on but is waiting to connect to a display device. In
this state, the GSD 20 does not transmit any sonar signals and is not
sending out any sonar information to display units. If a display unit is
connected and this code persists, check the wiring.
Solid Red (no blink) Software failure - Call Garmin Product Support. If the cause is a
software error, the display unit can show the error. Power must be
cycled to clear the error.
Red blinking, on for 1/10 second, off for 1/10 second
(very fast blink)
System alarm. The display device gives a message indicating the type
of failure. After the alarm condition is fixed, power must be cycled on
the GSD 20 to clear the alarm.
9GSD 20 Sonar Module
INSTALLATION INSTRUCTIONS
Physical Specifications
Size: 6.75” L x 4.75” W x 2.00” H
(17.2cm x 12.1cm x 5.1cm)
Weight: 1.5 lbs. (.680Kg)
Case: Fully gasketed, high-impact plastic and aluminum alloy, waterproof to IEC 529-IPX-7
Temp Range: 5°F to 158°F (-15°C to 70°C)
Power
Source: 10-35 Vdc
Usage: 18 watts max.
Fuse: AGC/3AG - 2.0 Amp
Sonar
Sounder Power: 500 watts (RMS)
4000 watts (peak to peak)
Frequency: 50/200 kHz
Depth: 1500 foot max depth*
* Depth capacity is dependent on water salinity, bottom type, and other water conditions.
Data Output
Source: Proprietary Garmin data format.
© Copyright 2004, 2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00255-00 Rev. E