Garmin Edge 305 With Cadence Sensor Quick Start Manual 190 00580 01_0D

Garmin-Edge-205-Quick-Start-Guide-785287 garmin-edge-205-quick-start-guide-785287

766-M-Edge-205-Manual-Quick-Start-Guide 766-m-edge-205-manual-quick-start-guide

768-M-Edge-305-Manual-Quick-Start-Guide 768-m-edge-305-manual-quick-start-guide

Edge 305 - Quick Start Manual EDGE_205_305_QSG_EN Free User Guide for Garmin GPS, Manual - page1

: Garmin Garmin-Edge-305-With-Cadence-Sensor-Quick-Start-Manual-722491 garmin-edge-305-with-cadence-sensor-quick-start-manual-722491 garmin pdf

Open the PDF directly: View PDF .
Page Count: 2

2. Attach the bike mount securely using two cable ties.

Note: Make sure the cable ties are threaded through both parts

of the bike mount.

3. Align the Edge with the bike mount so that the unit is vertical.

4. Slide the unit left until it snaps into place.

To release the unit:

Press down on the release lever, and slide the unit to the right.

➊

Charge the Battery

1. On the back of the Edge, pull up the weather cap from the

mini-USB port. Make sure that this area is completely dry to

prevent corrosion.

2. Plug the mini-USB end of the charger into the mini-USB port on

the unit.

3. Plug the A/C charger into a standard wall outlet. Charge the

Edge for at least 3 hours before using. When the battery is

completely charged, it can run for approximately 12 hours

before recharging.

➌

Configure the Edge

When you first turn on your Edge, the following setup screens appear.

Follow the on-screen instructions.

To configure your Edge:

➋

Mount the Edge

You can install the bike mount to the stem or handlebars. The stem

installation (shown here) provides a more sturdy location. Make sure

that the Edge is facing up for the best GPS reception.

To install the Edge on your bike stem:

1. Place the wedge on the bike stem, and then place the bike

mount on the wedge. Make sure the release lever is on the left.

For horizontal bars: Separate and remove the top part of the

mount, turn it 90 degrees, and replace. Continue with step 2.

For bars with a diameter less than 1 in (25.4 mm): Place

the additional rubber pad under the bike mount to increase the

diameter of the bar. The rubber pad also keeps the mount from

slipping. Continue with step 2.

Getting Started

1

power

• Press and hold to turn unit on/off.

• Press to turn backlight on/off.

2

mode

• Press to switch modes.

• Press to return to the previous page.

3

reset/lap

• Press and hold to reset the timer.

• Press to create a new lap.

4

start/stop

Press to start/stop the timer.

5

up/down

• Press to highlight options.

• Press to scroll through menus and data fields.

• Press to adjust contrast when on the Satellite page.

6

enter

Press to select options and to acknowledge messages.

Note: If the Edge locks up, press mode and reset/lap simultaneously

to reset the unit.











































































1

2

34

65

mini-USB port under

weather cap

➍

Acquire Satellites

Acquiring satellite signals may take 30–60 seconds. For

troubleshooting information, refer to the owner’s manual.

To acquire satellite signals:

Go outdoors to an open area. Press and hold the

Power button to turn on the Edge.

On the Satellite page, the available satellites are

flashing while the Edge searches for satellite

signals. Acquired satellites and each corresponding

bar below change to solid. The GPS accuracy

appears at the top of the page.

Wait while the Edge searches for satellites. For best

reception, make sure the Edge is facing up. Stand

still in an open area, and do not begin moving until

the Satellite page disappears. After the Satellite

page disappears, you can begin your ride.

Screens 4 and 5

apply to Edge 305

only.

123

45

release lever wedge

(optional)

bike mount



release lever

cable ties

3. Place the heart rate monitor directly on your skin, just below the

breastplate. Wrap the strap around your chest and attach the

strap to the other side of the heart rate monitor.

4. Adjust the strap so it stays in place during your ride.

5. When positioned correctly, verify that your Edge is receiving

data. The heart rate icon changes from flashing to constant

. If not, go to Main Menu > Settings > System >

Accessories to activate your heart rate monitor or restart scan.

For more information about the heart rate monitor, refer to the

owner’s manual.

Install the Heart Rate Monitor

The Edge 305 with heart rate includes a wireless heart rate monitor

that you wear directly on your skin, just below the breastplate.

To position the heart rate monitor:

1. Push one tab on the strap through the slot in the heart rate

monitor. Press the tab down.

sensors

2. Wet both sensors on the back of the heart rate monitor to

create a strong connection between your pulse and the

transmitter.

Install the GSC10™ Sensor

The Edge 305 with cadence includes a wireless speed and cadence

sensor. Both magnets must be aligned with their respective indication

line and be within 5 mm of the GSC10 for the Edge to receive data.

1. Place the GSC10 on the rear chain stay (the side opposite of

the drive train). Loosely attach the GSC10 using two cable ties.

2. Attach the pedal magnet to the crank arm using the adhesive

mount and a cable tie. Make sure the indication line on the

pedal magnet lines up with the indication line on the GSC10.

3. Unscrew and attach the spoke magnet. Make sure it is aligned

with the sensor arm indication line.

4. Unscrew and move the GSC10 sensor arm to within 5 mm of

the spoke magnet.

5. Press the Reset button on the GSC10. The LED turns red, then

green. Pedal to test the sensor alignment. The red LED blinks

each time the crank arm passes the sensor, and the green LED

blinks each time the wheel magnet passes the sensor arm.

6. When everything is aligned and working correctly, tighten

the cable ties, sensor arm, and spoke magnet. For more

information about the GSC10, see the owner’s manual.

Set Your Profiles

To set your user profile:

1. Press mode to access the Main Menu.

2. Select Settings > User Profile.

3. Specify your Gender, Birth Date, and

Weight using the arrows and the

enter button.

To set your bike profile:

1. Press mode to access the Main

Menu.

2. Select Settings > Bike Profile.

3. Specify your Bike profile

(configure up to three bikes) and

Weight.

4. If you are using a GSC10, select

Sensor Mounted. Then you can

specify Wheel Size and Tire Size.

May 2006 190-00580-01 Rev. D Printed in Taiwan

Garmin Training Center™

Use the Garmin Training Center software on your personal

computer to plan your advanced workouts and courses before

you ride and analyze them afterwards. Install Garmin Training

Center from the installation disk in the product box. For help

using Garmin Training Center, click the Help menu in the

software or press F1 on your keyboard.

reset button

cable ties

indication

line

GSC10 on rear chain stay

1

cable tie

Pedal magnet on crank arm

indication

line

2

sensor arm

indication

line

Spoke magnet on wheel

spoke

magnet

3

pedal

magnet

Quick Reference Guide

Edge™ 205/305

GPS-enabled computer for cyclists