Garnet Systems Co GAN1021 ADSL Modem User Manual 2222

Garnet Systems Co Ltd ADSL Modem 2222

users manual

GAN-1021 ADSL MODEM INSTALL GUIDE GARNET SYSTEMS CO.LTD
Scaleable ADSL Modem Installation Guide Before you start Step 1 – Gather system and service connection information System 1 Determining your Operating System 1Determining your Internet service protocol Determining your connection address and service configuration Step 2 – Install the ADSL modem card Hardware installation Step 3 – Install the drivers and establish an Internet service connection ADSL Connection mode selection Driver installation and Internet service connection. RFC 2364 - Point to Point Protocol over ATM Windows 98, 98SE. Windows 2000. RFC 1483 - Bridged Ethernet over ATM Windows 98, 98SE Windows 2000 Appendix Appendix A – Editing RFC 2364 Internet service connection Appendix B – Editing RFC 1483 Internet service connection Appendix C – Removing drivers Windows 98 Windows 2000 Appendix D – Diagnostic tools Accessing the diagnostic tools . Advanced diagnostic tools. Connector pin-out Appendix E – ADSL Configuration. Appendix F – System requirements
Before you Start! The Installation Guide tells you everything you need to know to install and use the GAN-1021 ADSL modem card. This guide is designed to walk you through the installation of the GAN-1021 card and drivers, and then through the establishment of an Internet service connection. This is a (3) step process. Step 1 – Gather system and service connection information Step 2 – Install the ADSL modem card Step 3 – Install the drivers and establish an Internet service connection ! If you’re a beginner to the Internet – or if you’re experienced but have never installed an ADSL PCI card before – Start at the beginning and work your way carefully through the instructions. It is important to gather all the information required before you actually install the PCI card and ADSL drivers. ! If you’re familiar with installing PCI cards and drivers - you may be able to browse the chapters to get the basics - However, it is still important to gather all the information required before you actually install the PCI card and ADSL drivers. Step 1 – Gather system and service connection information SYSTEM REQUIRMENTS Make sure your PC system meets ALL of the following requirements: Hardware: " IBM PC/AT or compatible " Pentium 500Mhz or faster " 30Mbytes available hard disk space or more " 2x CD-ROM drive or better " 32Mbyte available system memory or more Software: Your Operating System must be one of the following: Microsoft Windows 98, 98SE, 2000 DETERMINING YOUR OPERATING SYSTEM You will need to know the exact version of Microsoft Windows installed in your computer. If you do not know or are unsure, please proceed as follows to determine your version of the Microsoft Operating System. On the desktop, right click My Computer. Then select Properties. The version number of the Microsoft Windows Operating System installed in your computer will be displayed on the General tab. Refer to the following table for more detailed information.
Version System Description Release Name Win 98 4.10.1998 Window 98 Win 98A 4.10.2222A 2 nd Edition Windows 98 2 nd Edition Win 5.00.2195 Windows 2000. DETERMINING YOUR INTERNET SERVICE PROTOCOL Your Internet service protocol will be one of the following. Contact your ADSL service provider if you are unsure of your service type. RFC 1483 Bridged Ethernet over ATM RFC 2364 Point-to-Point Protocol over ATM DETERMINING YOUR CONNECTION ADDRESS AND CONFIGURATION You will need to know the connection address and configuration for your Internet service. Find your Internet Service Protocol below and proceed gathering the connection address and configuration. If you are unsure or do not have all the information, please contact your ADSL service provider. ! RFC1483 - Bridged Ethernet over ATM service requires the following information: IP Address . . . Subnet Mask . . . Gateway . . . (Domain Name Service) DNS Host DNS Domain DNS Server . . . VPI value VCI value VPI = ____ (Default VPI=0) VCI = ____ (Default VCI=35) ADSL Mode Type " ANSI T1.413 Issue 2 " ITU G.992.2 Annex A (G.lite) " ITU G.992.1 Annex A (G.dmt)
! RFC2364 – Point-to-Point Protocol over ATM User Name Password Logon Domain VPI value VCI value VPI = ____ (Default VPI=0) VCI = ____ (Default VCI=35) ADSL Mode Type " ANSI T1.413 Issue 2 " ITU G.992.2 Annex A (G.lite) " ITU G.992.1 Annex A (G.dmt). Step 2 – Install the ADSL modem card HARDWARE INSTALLATION WARNING! To avoid possible damage to your GAN-1021 card you need to use an anti-static grounding device or hold onto the metal chassis of the PC to provide anti-static grounding. 1. Shut down the system and switch the power off. 2. Unplug the AC power cable from the PC. 3. Remove the cover from the PC chassis. 4. Unscrew the “slot cover bracket” from an unused PCI slot. 5. Insert the card into an empty PCI slot. 6. Firmly press the GAN-1021 card into the slot and secure the card to the chassis with the chassis bracket screw. 7. Connect one end of a phone cable to the RJ-11 port on the GAN-1021 card and plug the other end of the cable into the ADSL data service. 8. Replace the cover of the PC chassis. ! Before you plug the power cable back into the PC system and turn the power on, go to Step 3 and determine the section/page you need to be on to install the drivers.
Step 3 – Install the drivers and establish an Internet service connection ADSL CONNECTION MODE SELECTION The GAN-1021 Multi-Mode Drivers will automatically determine the ADSL connection mode supplied by your ADSL service provider. If for any reason you require a mode setting different from the automatic default setting, you can manually set the mode as required. Please refer to Appendix E – ADSL Configuration – Select Protocol/Mode. The connection mode is one of the following: " ITU G.992.1 (G.dmt) ………....referred to as G.dmt " ITU G.992.2 (G.lite)……….......referred to as G.lite " ANSI T1.413 ………..................referred to as ANSI DRIVER INSTALLATION AND INTERNET SERVICE CONNECTION Refer to the following chart and locate your connection protocol with your corresponding Operating System (OS). Then proceed to the appropriate section/page. ! NOTE: You may need the Microsoft Windows Operating System installation files (CAB files) to complete the installation. The CAB files are contained in the Microsoft’s system CD-ROM. Some systems may have already installed the CAB files to the hard drive, but you should have the Microsoft Windows CD-ROM handy just in case.. RFC 2364 – POINT TO POINT PROTOCOL OVER ATM – WINDOWS 98, 98A system and turn the power on. 1. The Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. 2. Still in the Add New Hardware Wizard. You will be asked “What do you want Windows to do?” Select “Search for the best driver for your device”, then click Next. 3. Insert the CD labeled GARNET SYSTEMS CO.LTD. GAN-1021 Drivers into your systems CD-ROM drive. 4. Then select Specify a location and in the text entry bar type in your systems CD drive location letter ( D for example ), followed by a colon ( : ), then a back slash ( \ ), followed by the RFC 2364 driver for Windows 98 (2364w9x). For example, type in: D:\2364w9x Then click Next. 5. The Add New Hardware Wizard will appear and indicate the GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021. Click Next. 6. When the Service Option window appears, click Advanced.
7. The Service Options window now displays the Connection Address. Enter in the VPI, VCI and Framing values provided by your ADSL service provider. Click OK. NOTE: The default Framing setting is VC MUX. However, some ADSL service providers require LLC/SNAP. GARNET SYSTEMS CO.LTD. drivers also support LLC/SNAP. Please consult your ADSL service provider if you are unsure of the Framing setting or require more information. 8. The previous Service Option window will appear, click Next. 9. If prompted to insert your Windows CD do so at this time then click OK. Enter the <CD drive Letter> and then :\Win98 (e.g. D:\Win98) and click OK. 10. At the conclusion of the GARNET SYSTEMS CO.LTD. GAN-1021 driver installation, the Add New Hardware Wizard window appears and displays you new GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021. Click Finish. 11. The System Settings Change window appears. For the PC system to set up the GARNET SYSTEMS CO.LTD. GAN-1021 Drivers, a system Restart is required. Click Yes. NOTE: After restarting the system, the Diagnostic Tool icon (See Appendix D) is active and monitoring connectivity. 12. You must now make a dial-up network connection. At the Task bar, click on Start, and then select Programs, Accessories, Communications, followed by Dial-Up Networking. 13. The Dial-Up Networking window appears. Double-click the Make New Connection icon. 14. The Make New Connection window appears. The default name for the computer you are dialing is My Connection. However, you can name the connection anything you wish. In the Select a device bar, use the scroll down menu to locate the GARNET SYSTEMS CO.LTD. GAN-1021 ADAPTER, then click Next. 15. A new Make New Connection window appears. Enter in the Host Name or IP Address provided by your ADSL service provider, otherwise enter (0) zero, and click Next. 16. Another Make New Connection window appears. It will indicate that You have successfully created a new Dial-Up Networking connection called “My Connection”. Click Finish.. 17. The new “My Connection” will appear in the Dial-Up Networking window. Double-click the new “My Connection” icon to begin a Dial-Up session. 18. The Connect To window appears indicating “My Connection”. Type in the User name and Password supplied by your Internet Service Provider (ISP). Click Connect. 19. The Connection Established window will appear indicating You are connected to “My Computer”. Click Close and the Diagnostic tool icon appears on the task bar.
RFC 2364 – POINT TO POINT PROTOCOL OVER ATM – WINDOWS 2000 After installing the ADSL modem card, plug the power cable back into the PC system and turn the power on. 1. After installing the ADSL modem card, power on the PC system. After start-up, the Found New Hardware Wizard will appear. Click Next. 2. Still in the Found New Hardware Wizard, select Search for a Suitable Device…Click Next. 3. Next you will be prompted to software drivers. Select Specify a location. Click Next. 4. Insert the GARNET SYSTEMS CO.LTD. ADSL Driver CD into the System CD-ROM drive. Click Browse to locate the : 2364w2k driver on your CD-ROM then Click OK. 5. The Found New Hardware Wizard will then Find the GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021. ClickNext. 6. The Digital Signature Not Found window appears. You will be asked; Do you want to continue installation? Click Yes 7. When the Service Option window appears, click Advance. 8. The Advance Service Option appears. In the Network Protocol and the PVC Settings section, enter the VPI/VCI and Framing values supplied by your ADSL service provider. 9. In the Select ADSL Mode Section, select the modes(s) recommended by your ADSL Service provider. Click on the mode(s) required and then click OK NOTE: The Service mode type will be one of the following: " ITU G.992.1 (G.dmt) ………....referred to as G.dmt " ITU G.992.2 (G.lite)………......referred to as G.lite " ANSI T1.413 ……….................referred to as ANSI 10. The Previous Service Option window will appear. Click Next. 11. The Found New Hardware Wizard will prompt that windows has finished installing the software for this device. Click Finish. NOTE: You may be asked if you want to restart your computer, if so click Yes. Otherwise you will need to manually restart your computer at this time. 12. On your desktop double-click My Computer, Control Panel, and then Network and Dial-up Connections. 13. The Network and Dial-up Connections window appears. Double click on Make a New Connection. 14. The Network Connection Wizard window appears. Click Next 15. Set the Connection option to Dial-up to Private Network, and then click Next.
16. The Network Connection Wizard appears. You will be prompted for a phone number. Enter the phone number provided by your ADSL service provider. Click Next. 17. You will be prompted to select your user configuration, typically only for myself. Click Next. 18. The Network Connection Wizard appears. You will be prompted to name your Network Connection. The default is Dial-up Connection. Rename the connection as you choose and then click Finish..GAN-1021 Installation Guide 19. The Connect My Connection window will appear. Enter your User Name and Password supplied by your ADSL service provider. You are now ready to make a network connection. Click Dial. 20. The Connection complete window appears, click OK. RFC 1483 – BRIDGED ETHERNET OVER ATM – WINDOWS 98, 98A After installing the GARNET SYSTEMS CO.LTD. GAN-1021 card, plug the power cable back into the PC system and turn the power on. 1. The Add New Hardware Wizard will detect the GARNET SYSTEMS CO.LTD. GAN-1021 as a PCI Network Controller, click Next. 2. Still in the Add New Hardware Wizard you will be prompted What do you want Windows to do? Select the Search for the best driver for your device. Click Next. 3. Again in the Add New Hardware Wizard, select the Specify a location option and then type in your systems CD drive location letter ( D for example ), followed by a colon ( : ), then a back slash ( \ ), followed by the RFC1483 driver for Windows 98 (1483w9x). For example, type in: D:\1483w9x Then click Next. 4. The Add New Hardware Wizard will then find the GARNET SYSTEMS CO.LTD. ADSL PC NIC-GAN-1021, click Next. 5. When the Service Option window appears, click Advanced. 6. The Service Options window now displays the Connection Address. Enter in the VPI and VCI values provided by your ADSL service provider. Make sure the Framing is set to LLC/SNAP. Click OK. NOTE: The default Framing setting is LLC/SNAP. However, some ADSL service providers require VC MUX. GARNET SYSTEMS CO.LTD. drivers also support VC MUX. Please consult your ADSL service provider if you are unsure of the Framing setting or require more information.
7. The previous Service Option window will appear, click Next. NOTE: During the installation process you may be asked to insert your Windows 98 CD. Insert the Windows 98 CD into your systems CD drive and click OK. If during the file copying process a file is reported as “not found” enter the path <CD Drive letter> and :\Win98 (e.g. D:\Win98) 8. The Add New Hardware Wizard appears, click Finish. 9. When the System Settings Change window appears and asks; Do you want to restart your computer now? Click Yes. NOTE: You must now make an Internet connection 10. Double click My Computer, Control Panel, and then Network. 11. In the Network window, select the Configuration tab. 12. Scroll through the installed network components list. Highlight the TCP/IP-> GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021 and click Properties. 13. The TCP/IP Properties window appears. Select IP Address tab. Select Specify an IP address. The IP address and Subnet Mask will turn from gray to clear. Enter your IP Address and Subnet Mask provided by your ADSL service provider. 14. Select the Gateway tab. Enter your gateway information provided by your ADSL service provider into the New gateway box and click Add. If you have more than one gateway number, repeat this step. 15. Select DNS Configuration tab. Select the Enable DNS option. NOTE: You now need to have available the Host, Domain and DNS settings provided by your ADSL service provider. 16. Enter your host name into Host: box. 17. Enter your domain name into Domain: box. 18. Enter DNS number into DNS Server Search Order box and click Add. If you have more than one DNS numbers, repeat this step. 19. After setting all the necessary TCP/IP properties, click OK. 20. The Network window appears. Click OK. 21. The System Setting Change window appears. You will be asked if you want to restart your computer. Click Yes.
RFC 1483 – BRIDGED ETHERNET OVER ATM – WINDOWS 2000 After installing the ADSL modem card, plug the power cable back into the PC system and turn the power on. 1. After installing the ADSL modem card, power on the PC system. After start-up, the Found New Hardware Wizard will appear. Click Next. 2. Still in the Found New Hardware Wizard, select Search for a Suitable Device…Click Next. 3. Next you will be prompted to software drivers. Select Specify a location. Click Next. 4. Insert the ADSL Driver CD into the System CD-ROM drive. Click Browse to locate the : 2364w2k driver on your CD-ROM then Click OK. 5. The Found New Hardware Wizard will then Find the GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021. Click Next. 6. The Digital Signature Not Found window appears. You will be asked; Do you want to continue installation? Click Yes 7. When the Service Option window appears Click Advance. 8. The Advance Service Option appears. In the Network Protocol and the PVC Settings section, enter the VPI/VCI and Framing values supplied by your ADSL service provider. 9. In the Select ADSL Mode Section, select the modes(s) recommended by your ADSL Service provider. Click on the mode(s) required and then click OK NOTE: The Service mode type will be one of the following: " ITU G.992.1 (G.dmt) ………....referred to as G.dmt " ITU G.992.2 (G.lite)………......referred to as G.lite " ANSI T1.413 ……….................referred to as ANSI 10. The Previous Service Option window will appear. Click Next. 11. The Found New Hardware Wizard will prompt that windows has finished installing the software for this device. Click Finish. NOTE: You may be asked if you want to restart your computer, if so click Yes. Otherwise you will need to manually restart your computer at this time. 12. On Desktop Double-click My Computer, Control Panel, and then Network and Dial-up Connections. 13. The Network and Dial-up Connections window appears. Right-click on the Local Area Connection for your GARNET SYSTEMS CO.LTD. ADSL PCI NIC- GAN-1021. 14. The Local Area Connection window appears. Click on the Internet Protocol (TCP/IP), then click Properties.
15. The Internet Protocol (TCP/IP) window appears. Under the General tab, enable Use the following IP address. The default settings for IP configurations will turn from gray to clear. Enter the IP address, Subnet Mask, and the Default Gateway supplied by your ADSL service provider. Click OK. 16. The previous General Tab window appears. Click OK.GAN-1021 Installation Guide 17. The Network and Dial-up Connection window appears. Close this window and your connection is complete. APPENDIX A - EDITING RFC 2364 INTERNET SERVICE CONNECTION W98, 2000 1. To view or edit the ADSL connection service address, right-click the Diagnostic Tool icon (located on the Taskbar), and select the Configuration option. 2. The PVC Setup (Permanent Virtual Connection) window displays the connection service address. Click Close to exit window. 3. To edit the connection service address, select and enter the VPI and VCI address in the field shown and click PVC Setting. 4. To accept a Connection Address that has been changed (Restart the PC system) click Yes. APPENDIX B - EDITING RFC 1483 INTERNET SERVICE CONNECTION W98 NOTE: This section includes the IP configuration specifics for Windows 98, 98SE. Windows 98 is slightly different from that of Windows 98SE. Other than minor screen differences, the process for editing the IP address settings is the GAN-1021e for Windows 98 and Windows 98SE. 1. At the desktop, double click My Computer, then double click Control Panel to view the contents of the control panel. In the Control Panel window, double click the Network icon. NOTE: The Network window shortcut is a right-click the Network Neighborhood on your desktop then left-click Properties. 2. Select the Protocols tab of the network window. Select TCP/IP Protocol and click Properties. 3. Select the IP address option and note that the IP Address and Subnet Mask regions will turn from gray to active. 4. Enter the IP Address (e.g. 192.168.4.39) and subnet mask (e.g. 255.255.255.0). 5. The Default Gateway is also entered in this window. NOTE: Please refer to your ADSL service provider and enter (or edit) the following fields: 6. Enter the Host Name (e.g. GAN-1021) and Domain (e.g. pacbell.net).
NOTE: To enter the Domain search (DNS) entries, click Add then enter the address. Click Add to save the address. Repeat the process for additional DNS entries. 7. Click OK to update the changes. EDITING RFC 1483 INTERNET SERVICE CONNECTION W2000 1. At the Desktop, Right Click My Network Places, select and click on Properties. 2. The Network and Dial-up Connections window appears, Right click on the Local area Connection and select Properties. 3. Select the Protocols tab of the network window. Select TCP/IP Protocol and Click Properties. 4. Select the IP address option and note that the IP Address and Subnet Mask regions will turn from Gray to active. 5. Enter the IP Address (e.g. 192.168.4.39) and then the Subnet mask (e.g. 255.255.255.0). 6. The Default Gateway is also enter in this window. 7. Enter the Preferred Domain address (DNS) server, and Alternate (DNS) server, provided by your ADSL service provider, Click OK to update the Changes.. APPENDIX C – REMOVING DRIVERS WINDOWS 98 1. To Delete GARNET SYSTEMS CO.LTD. GAN-1021 drivers; on the desktop, right-click on My Computer, then select Properties, click on the Device Manager tab, then double click Network adapters. 2. Select the GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021, then click on the Remove button. 3. A warning message “You are about to remove this device from your system” will appear. Click OK to remove drivers or click Cancel to abort the driver removal. 4. The PC system must be restarted for the changes to take effect. Click Yes. WINDOWS 2000 1. On the desktop, right click on My Computer. 2. Select Properties, the system window appears. 3. Select the Hardware Tab, and click on the Device Manager button. 4. Double click on Network Adapters. 5. Select the GARNET SYSTEMS CO.LTD. ADSL PCI NIC-GAN-1021, right click on it and select uninstall.
6. A warning message window appears " You are about to remove this device from your system", click OK to remove drivers or click Cancel to abort the driver Removal.. APPENIDX D - DIAGNOSTIC TOOLS ACCESSING THE DIAGNOSTIC TOOLS: The diagnostic tools allow the user to monitor the ADSL connectivity, setup the service connection address, and run diagnostic tests. The Diagnostic Tools icon is displayed on the task bar as shown. By positioning the mouse cursor over the icon, the upstream and downstream line rates of the ADSL connection are displayed. The Diagnostic Tools icon consists of two lights side by side. The left light indicates data is being transmitted whereas the right light indicates data is being received. The state of the connection can be determined as follows: COLOR CODE DESCRIPTION Red, Red No ADSL connection and or handshaking. Check your cable connections. Black/Yellow flashing ADSL Handshaking – Connection not established. Black, Black ADSL connection established – no data traffic or idle connection Black, Green ADSL connection established – receiving data (TX/off, RX/on) Green, Black ADSL connection established – transmitting data (TX/on, RX/off) Green, Green Connection established – transmitting and receiving data (TX/on, RX/on) Disconnected or a driver problem exists. Try using Connect command in Diagnostic Tools. If persists, restart the PC system and/or last reload drivers. ADVANCED DIAGNOSTICS TOOLS Right-click the Diagnostic Tools icon on the right hand side of the status bar to display the menu, then Click Open. The ADSL Diagnostic Tools window appears on the desktop. The three tabs of the Diagnostic Tools are ADSL Status, ATM / ADSL Statistics and Diagnosis.
ADSL STATUS window displays the current state of the GARNET SYSTEMS CO.LTD. ADSL connection, including current ADSL State, ADSL rotocol in use and the net data rates for upstream and downstream data. NOTE: ADSL protocols supported by the GARNET SYSTEMS CO.LTD. drivers are T1.413, G.dmt and G.lite. The protocol must be supported also by the ADSL equipment located at the central office. The GARNET SYSTEMS CO.LTD. drivers use the protocol that results in the most efficient ADSL connection.. ATM / ADSL STATISTIC window keeps tabs on errors that might affect overall system performance. The counts are reset whenever the PC system is restarted. Re-training Count tracks the number of ADSL connections performed. Due to unexpected line condition changes, the GARNET SYSTEMS CO.LTD. drivers can retrain the connection causing the Re-training Count total to increment. The Diagnostic Tool icon will flash yellow while reconnecting. . ADSL implements Reed Solomon (RS) error checking: . FEC Count tracks the forward error correction count. . CRC Count tracks the accuracy of correcting data errors over each 17msec. . ATM HEC Count (header error check) errors are recorded as an indication of ATM packet accuracy. . As a measure of packet transfer performance, the Packet Errors are counted and tracked against the total number of Packets Received. An error rate of less than 0.1% is reasonable under clean ADSL line conditions. . If you have Bad Received Packets and are concerned about your service, multiply the Bad Received Packets count by 1000 and compare the result with the total Packets Received count. If the number is smaller than the total Packets Received count, then the board is operating normally. DIAGNOSIS window is used to verify the GAN-1021 card functionality. Running the Diagnosis program will disconnect the NIC from the ADSL line. Close all Dial-up sessions and close all files before running the Diagnostic program. Right-click the Diagnosis Tool icon (located on the Taskbar), then select the Diagnosis option. Product Information, e.g. driver revisions, are displayed by clicking the Product Infotab. Click Run Diagnostics to run the diagnostic program that will test PC functionality and report the status.
A warning message pops up that the ADSL service will disconnect before performing the Diagnostic test. If connected to the Internet at this time, disconnect any Dial-up sessions. Click Yes to begin the diagnostic program or click No to exit diagnostic program. The iagnostic program performs a brief hardware check and displays the hardware status. If the GAN-1021 fails the Diagnostic tests (shown below), then record the test result and contact customer support.. CONNECTOR PIN-OUT The GARNET SYSTEMS CO.LTD. GAN-1021 card is equipped with a RJ-11 jack for connection to the ADSL data port. The center two pins, pins 3 and 4, are used for ADSL data. For the GAN-1021 card to make a proper ADSL connection, the installed ADSL data port should also use pins 3 and 4 for data. If the ADSL data port installation uses pins 2 and 5 for data, then a wiring converter will be required. Do not alter or remove the wiring converter if present. Consult with your ADSL provider before attempting any wiring changes.. APPENDIX E – ADSL CONFIGURATION 1. On the task bar on the right hand side locate the GARNET SYSTEMS CO.LTD. ADSL Diagnostic Tool icon. Right click on the Diagnostic Tool icon, then click Configuration. 2. The Configuration window appears. From the Configuration window the PVC Setup, Protocol /Mode and Rate can all be set as required by your ADSL service provider. PVC SETUP NOTE: Your ADSL PVC settings are typically set through the Systems Options window of the driver installation wizard. However, the values can easily be changed as follows: 1. Enter in the VPI and VCI and Framing values provided by your ADSL service provider, then click the Setting button. 2. Verify that the Protocol/Mode and Rate settings are correct and the click Close. ! SELECT PROTOCOL/MODE NOTE: The GAN-1021 Multi-Mode Drivers will automatically determine the ADSL connection mode supplied by your ADSL service provider. The priority of selection is G.lite, G.dmt, and T1.413. If for any reason you require a mode setting different from the automatic default setting, you can manually set the mode(s) as required. To change the ADSL connection mode setting proceed as follows:
1. In the Select Protocol & Rate section you shall find the ADSL Mode selection options. Select the ADSL mode(s) you require, by clicking in the selection box(s). " ITU G.992.1 (G.dmt) ………....referred to as G.dmt " ITU G.992.2 (G.lite)………......referred to as G.lite " ANSI T1.413 ……….................referred to as ANSI 2. After you select and check the mode(s) you require, click Set Protocol & Rate. Your new ADSL Mode settings are now in effect. 3. Verify that the PVC and Rate settings are correct and the click Close. ! SELECT RATE NOTE: The default downstream rate of 1.5Mbps is recommended, as the majority of service providers today supply 1.5Mbps. This allows for video streaming of about 1Mbps resulting in A CPU utilization of under 30% @ 300 MHz. However, for higher speed ADSL service and /or CPU’s, the rate can be increased. The rates can be easily be changed as follows: 1. To change the rate settings enter in the Downstream Rate and Upstream Rate required, then click the Set Protocol & Rate button. 2. Verify that the Protocol/Mode and PVC settings are correct and the click Close.. APPENDIX F - SYSTEM REQUIREMENTS Power Requirements  0.75A Max @ +5V ± 5%, 0.1A max @ ± 12V, ± 5% Environmental Requirements  Operating Temperature: 0 °C to 70C with airflow  Non-operating Temperature: -10 °C to 85 °C  Operating Humidity: 10% to 90% non-condensing  Non-operating storage humidity: 5% to 95% non-condensing

Navigation menu