Garrett Metal Detectors PPATZ Pro-Pointer AT Z-Lynk User Manual 1538820 ProPointer AT ZLynk Manual indd

Garrett Metal Detectors Pro-Pointer AT Z-Lynk 1538820 ProPointer AT ZLynk Manual indd

User Manual

®OWNER’S MANUAL1538820.ProPointer_AT_ZLynk_Manual.indd 1 3/8/2018 10:18:00 AM
2(Reverse side of pinpointer)FEATURES ON/OFF, Retune, Adjust Button Pinpointing Tip 360° Side-Scan Area Exclusive Scraping Blade LED Flashlight Waterproof Speaker Lanyard Attachment Loop Sealed Battery Cover Ruler in Inches and Centimeters Internal Wireless Transmitter1538820.ProPointer_AT_ZLynk_Manual.indd 2 3/8/2018 10:18:02 AM
3Powering On Press and release the button () while holding the detector away from any metallic objects. You will hear 2 beeps and the LED () will remain on. Powering OffPress and hold the button for a half second until you hear a single beep (or single vibration in Silent Mode), indicating power down.Changing SettingsThe Pro-Pointer AT Z-Lynk has three Sensitivity settings and two detection settings: Audio-plus-Vibrate or Vibrate-only (silent). To enter adjustment mode, press and hold the button () for 2 seconds—indicated by a single beep followed by a dual-tone beep and flashing LED. (Note: In Silent Mode, beeps are replaced by vibration pulses.) The first button press after entering adjustment mode indicates the current setting. Repeatedly press the button to cycle through the 6 settings: 1 beep = minimum Sensitivity, with audio 2 beeps = medium Sensitivity, with audio (Default setting) 3 beeps = maximum Sensitivity, with audio 1 vibrate = minimum Sensitivity/Silent 2 vibrate = medium Sensitivity/Silent 3 vibrate = maximum Sensitivity/Silent To exit adjustment mode, press and hold the button for 2 seconds—indicated by a dual-tone beep (dual vibrate in Silent Mode), or wait 5 seconds for automatic exit.1538820.ProPointer_AT_ZLynk_Manual.indd 3 3/8/2018 10:18:02 AM
4 Notes: • Lower Sensitivity settings are recommended to prevent detection of highly mineralized grounds. • Detection remains operable during the adjustment mode. • Settings will be remembered when the unit is switched off and back on.Wireless Operation Reconnecting: Once paired, the pinpointer will instantly reconnect to the last paired receiver. The receiver must be powered on first. The pinpointer’s external audio will switch off when paired. Pairing: This product can be be paired wirelessly with any Garrett Z-Lynk receiver using the following steps. 1. First, switch on the receiver (i.e. Garrett MS-3 Wireless Headphones or Garrett WR-1 Z-Lynk device). 2. Hold the pinpointer within 6 inches (15cm) of the headphone or the WR-1 device. 3. Switch the pinpointer on and wait (approximately 3 seconds) for the light on the headphones (or WR-1) to go from blinking to steady. 4. If the units do not pair, switch the pinpointer off and then on again. Note: If you have trouble pairing, make sure that the receiver is on first, and that the two devices are within six inches of each other. Also, be sure that a previously paired headphone or WR-1 is not powered on in the vicinity (20 to 50 feet). 1538820.ProPointer_AT_ZLynk_Manual.indd 4 3/8/2018 10:18:02 AM
5A solid red light on the MS-3 Wireless Headphones or WR-1 Z-Lynk receiver indicates proper pairing with the pinpointer.Solid red light indicates pairing.Solid red light indicates pairing.1538820.ProPointer_AT_ZLynk_Manual.indd 5 3/8/2018 10:18:03 AM
Fast Retune for Mineralized GroundTo tune out the detection of saltwater, wet sand or highly mineralized ground, hold the tip of the Pro-Pointer AT Z-Lynk to the water, sand or soil and quick-press the button () for an instant Retune. If necessary, repeat this Fast Retune to further eliminate any environmental response. Note: An alternate means of eliminating the ground response is to reduce Sensitivity.Fast Retune feature quickly tunes out mineralized ground, saltwater, wet sand, and other challenging environments.Precisely Pinpointing Large TargetsSlowly scan toward the object until the response increases to full/constant alarm. Then quick-press the button to instantly retune and narrow the detection field. Continue scanning toward the object to find its precise location. Repeat this Fast Retune to further narrow detection field as needed.Lost Pinpointer AlarmAfter 5 minutes of being ON without a button press, the Pro-Pointer AT Z-Lynk will begin emitting progressively faster warning chirps for 60 minutes. Press the power button to reset. 61538820.ProPointer_AT_ZLynk_Manual.indd 6 3/8/2018 10:18:03 AM
7Auto-Off FeatureAfter one hour of warning chirps, the Pro-Pointer AT Z-Lynk will power off automatically. Scraping BladeThis rugged edge is ideal for sifting through dirt while searching for the target. The Pro-Pointer AT’s 360º-side-scan detection allows the detector to alarm when the blade is passed in close proximity to a metallic target.Lanyard Attachment ClipUse to attach the Pro-Pointer AT to your belt, digging pouch or your detector (if desired).HolsterSecure to any standard size belt. A metal snap within the holster will cause the pinpointer to alarm if put away while powered on.RulerThe Pro-Pointer AT has a ruler molded into its exterior to measure a target’s depth in either centimeters or inches.Low Battery AlarmWhen the battery becomes low, the detector will sound an alternating dual-tone alarm. Replace the 9V battery as soon as possible.1538820.ProPointer_AT_ZLynk_Manual.indd 7 3/8/2018 10:18:03 AM
8Battery ReplacementSimply rotate the battery cover counterclockwise to remove and clockwise to tighten by hand. To properly install the 9V battery, match the larger battery terminal to the larger opening in the compartment. Remove the battery when the unit is to be stored more than 30 days.Please dispose of used batteries in accordance with local codes and regulations. Consult your local environmental control or disposal agency for further details.Operational Information and Tips• Operation is completely automatic. All metals will be detected including ferrous and non-ferrous. • When a target is detected, the Pro-Pointer AT Z-Lynk will produce an audio and/or vibration alert. The rate of the pulsing audio and vibrations increase proportionately as the pinpointer is moved closer to a metallic target. • Maximum detection of very small targets is obtained against the side about ½” from the tip.• To avoid cancelling out a target, do not turn on the Pro-Pointer AT while it is adjacent to the target.• Because the Pro-Pointer AT is a static, non-motion detector, optimum operation is achieved when the unit is switched off between uses.• Avoid using the Pro-Pointer AT as a digging or prying tool. It is designed for flat side-scanning and precise pinpointing with its tip. It is not intended to be used with excessive force.1538820.ProPointer_AT_ZLynk_Manual.indd 8 3/8/2018 10:18:03 AM
9• For water use, do not exceed 20 feet (6 meters) depth. Make sure the battery cap threads are free of sand, sediment, etc. and that O-ring is periodically lubricated with silicone grease to maintain a tight seal.• Radio signals do not transmit through water, so if you will be hunting fully submerged, you must rely upon the Pro-Pointer’s vibration and audio alerts without the benefit of headphones.• To remove dried dirt, mud or other debris from the unit, simply hand wash it with soap, water, and a soft cloth. Do not use any type of abrasive or chemical cleaners which could scratch or erode its surface.1538820.ProPointer_AT_ZLynk_Manual.indd 9 3/8/2018 10:18:04 AM
10RegulatoryThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Ce produit est conforme aux normes RSS exemptes de licence d’Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) ce dispositif ne peut pas provoquer d’interférences et (2) ce dispositif doit accepter toute interférence, y compris celles pouvant entraîner un dysfonctionnement. Wireless Transmitter SpecificationsAudio Delay: 17 milliseconds (6x faster than Bluetooth®)Audio Bandwidth: 30-18,000 HzOperating Frequency: 2406–2476 MHzTransmit Power: 8.0 dBm EIRPCertications: FCC, CE, IC, AS/NZ1538820.ProPointer_AT_ZLynk_Manual.indd 10 3/8/2018 10:18:04 AM
The Garrett Pro-Pointer AT Z-Lynk is manufactured in the United States of America and in accordance with Garrett’s ISO 9001 internationally certified Quality Management System and meets the following international standards: • FCC • CE • RoHS • ICNIRP • IEC 529-IP 68SPECIFICATIONSModel Name: Garrett Pro-Pointer®AT Z-LynkOperating Temperatures: -4ºF (-20ºC) to 130ºF (54ºC) Operating Frequency: 11.5 kHzWaterproof Rating: 20 foot (6 meter) maximum depth; IP 68 Tuning: Automatic or manual retuneIndicators: Proportional audio/vibration pulse rateControls: Power, Retune, Adjust switchDimensions: Length: 9” (22.9 cm) Thickness: 1.5” (3.8 cm) tapered to .875” (2.2 cm)Weight: 6.5 oz. (0.2 kg.), with batteryBattery: Single 9V (included). Alkaline batteries are recommended to achieve longest operating life.Warranty: 2 Years, Limited Parts/LaborPatent Information: US 7,575,065; D583,261 and patents pendingGarrett Metal Detectors, garrett.com, Z-Lynk, and PRO-POINTER are trademarks and registered trademarks of Garrett Electronics Inc. © 2018 Garrett Metal Detectors. 1538820.A.0318MADE INTHE USA1538820.ProPointer_AT_ZLynk_Manual.indd 11 3/8/2018 10:18:04 AM

Navigation menu