Ge Appliances 26934 Users Manual

26934 to the manual 6f1525af-8944-4517-acf2-ab027cd3b295

2015-01-23

: Ge-Appliances Ge-Appliances-26934-Users-Manual-253840 ge-appliances-26934-users-manual-253840 ge-appliances pdf

Open the PDF directly: View PDF .
Page Count: 2

INTRODUCTION

CAUTION: When using telephone equipment,

there are basic safety instructions that should

always be followed. Refer to the IMPORTANT

SAFETY INSTRUCTIONS provided with this

product and save them for future reference.

Your Caller ID phone stores and displays specific

information, provided by your local telephone company, to

subscribers of Caller ID or similar caller identification

services.

Your Caller ID phone enables you to:

•Identify callers before you answer the phone.

•View the time and date of each incoming call.

•Record up to 40 Caller ID messages sequentially.

•Know who called while you were away.

To get the most from your new phone, we suggest that

you take a few minutes right now to read through this

user's guide.

IMPORTANT: In order to use all of the features of this

phone, you must subscribe to either the standard

Name/Number Caller ID Service or Call Waiting

Caller ID Service. To know who is calling while you are

on the phone, you must subscribe to Call Waiting

Caller ID Service.

IMPORTANT: Because cordless phones operate on

electricity, you should have at least one phone in your

home that isn’t cordless, in case the power in your

home goes out.

BEFORE YOU BEGIN

PARTS CHECKLIST

Make sure your package includes the items shown here.

INSTALLATION

DESKTOP INSTALLATION

NOTE : The handset can be charged facing up or down.

1. Set the RINGER switch (on the handset) to ON and place

the handset in the cradle on the base.

2. Plug the power supply into the power jack on the

bottom of the base and the other end into an electrical

outlet. The in use/charge indicator comes on, verifying

the battery is charging.

Allow the phone to charge for 12 hours prior to first use.

If you don't properly charge the phone, battery

performance will be compromised.

NOTE: DO NOT connect the telephone line to the

modular jack until the phone has charged for 12 hours.

3. Plug the telephone line cord into the PHONE LINE jack

on the bottom of the base and into a modular jack.

CAUTION: Use only the ATLINKS USA, Inc.

5-2559(black) and 5-2558(white) power supply

that came with this unit. Using other power

supplies may damage the unit.

NOTE: The phone automatically defaults to touch-

tone dialing. To change to pulse (rotary) dialing, see

"TONE/PULSE DIALING." If you don't know which

type of service you have, check with your local

telephone company.

WALL MOUNT INSTALLATION

Because it is necessary to charge the handset for 12 hours

prior to connecting the phone for use the first time, it is

better to leave the unit on a flat surface during initial

charge before attempting to hang it on the wall.

1. Set the RINGER switch (on the handset) to ON and place

the handset in the cradle on the base.

2. Plug the power supply into the power jack on the

bottom of the base and the other end into an electrical

outlet. The in use/charge indicator comes on, verifying

the battery is charging.

Allow the phone to charge for 12 hours prior to first use.

If you don't properly charge the phone, battery

performance will be compromised.

NOTE: DO NOT connect the telephone line to the

modular jack until the phone has charged for 12 hours.

3. Plug the telephone line cord into the PHONE LINE jack on the

bottom of the base and the other end into a modular jack.

4. Slip the mounting holes on the bracket over the wall

plate posts and firmly slide the unit down into place

(wall plate not included).

5. Place the handset in the cradle.

NOTE: If desired, gather the extra line cord together,

and fasten with a wire tie.

NOTE: The phone automatically defaults to touch-

tone dialing. To change to pulse (rotary) dialing,

see "TONE/PULSE DIALING." If you don't know

which type of service you have, check with the

phone company.

CAUTION: Use only the ATLINKS USA, Inc.

5-2559(black) and 5-2558(white) power supply

that came with this unit. Using other power

supplies may damage the unit.

SET UP

There are three programmable menus available: Language,

Tone/Pulse Dialing and Area Code.

LANGUAGE SETTING

1. Make sure the phone is OFF (not in TALK mode).

2. Press the flash/program button until “ 1ENG 2FRA 3ESP”

shows in the display. “1ENG” is the default setting.

3. Use the CID/VOL left (-) or right (+) arrow button to

scroll to 1ENG 2FRA 3ESP, or use the touch tone

pad on the handset to enter the desired setting. For

example, to choose English, press the number 1 key.

1ENG is the default setting.

4. Press flash/program to store selection. You will hear a

confirmation tone.

TONE/PULSE DIALING

1. Make sure the phone is OFF (not in TALK mode).

2. Press the flash/program button until “ 1TONE 2PULSE”

shows in the display. “1TONE” is the default setting.

3. Use the CID/VOL left (-) or right (+) arrow button to

scroll to 1TONE or 2PULSE, or use the touch tone

pad on the handset to enter the desired setting. For

example, to choose TONE dialing, press the number 1

key.

1TONE is the default setting.

4. Press flash/program to store selection. You will hear a

confirmation tone.

AREA CODE SETTING

1. Make sure the phone is OFF (not in TALK mode).

2. Press the flash/program button until “- - - SET AREA

CODE” shows in the display. “

- - -”

is the default setting.

3. Use the handset number pad to enter your three digit

area code.

4. Press flash/program to store selection. You will hear a

confirmation tone.

CORDLESS PHONE BASICS

MAKING A CALL

To make a call, press the TALK button before you dial and

press it again to hang up.

REDIAL

While the phone is on, press the redial button to redial the

last number you dialed (up to 32 digits). If you get a busy

signal, and want to keep dialing the number, just press redial

again (you don't have to turn the phone off and back on).

FLASH

Use the flash/program button to activate custom calling

services such as call waiting or call transfer, which

are available through your local phone company.

TIP: Don’t use the TALK button to activate custom

calling services such as call waiting, or you’ll hang up

the phone.

IN USE INDICATOR LIGHT

The in use indicator is lit when the handset is charging in

the cradle on the base or when the phone is ON. It flashes

when you receive a call or when the PAGE button is

pressed.

CHANNEL BUTTON

While talking, you might need to manually change the

channel in order to get rid of static. Press and release the

channel/delete button to advance to the next channel. The

current channel number appears on the left side of the

display.

TEMPORARY TONE

This feature enables pulse (rotary) service phone users to

access touch-tone services offered by banks, credit card

companies, etc., by pressing the *tone/cancel button to

temporarily make the phone touch-tone compatible. To get

information about your bank account, for example, you would:

1. Call the bank’s information line.

2. Press the *tone/cancel button after your call is answered.

3. Follow the voice instructions to complete your transaction.

4. Hang up when finished. The phone returns to Pulse

(rotary) service.

CANCEL

Press the *tone/cancel button to cancel any command you

initiated.

FINDING THE HANDSET

This feature helps to locate a misplaced handset.

Press the page button on the base. The handset beeps

continuously for about two minutes or until you press any

button on the handset. You may also press page to cancel.

NOTE: The ringer does not have to be ON for this

feature to work.

RINGER SWITCH

The ringer switch must be ON for the handset to ring

during incoming calls.

VOLUME

While talking, press the VOLUME buttons (left and right

arrows) to adjust the listening level of the handset's

earpiece. There are four volume levels. Press the right

arrow (+) button to increase the volume level, and press

the left arrow (-) button to decrease. VOL 1 is the lowest

level and VOL 4 is the loudest.

CALL TIMER

While you are talking on the phone, the total talk time is

displayed on the bottom line of the display.

CALLER ID FEATURES

This unit receives and displays information transmitted by

your local phone company. This information can include

the phone number, date, and time;

the name, phone

number, date, and time. The unit can store up to 40 calls

for later review.

CALLER ID WITH CALL WAITING

Provided you subscribe to Caller ID with Call Waiting

service from your phone company, you are able to see who

is calling when you hear the call waiting beep. The caller

identification information appears in the display after you

hear the tone.

•Press the flash/program button to put the current person

on hold so that you can answer the incoming call.

IMPORTANT: In order to use the Caller ID functions

with this unit, you must subscribe to either the

standard Name/Number Caller ID Service or Call

Waiting Caller ID Service. To know who is calling while

you are on the phone, you must subscribe to Call

Waiting Caller ID Service.

RECEIVING AND STORING CALLS

When you receive a call, the information is transmitted by

the phone company to your Caller ID telephone between

the first and second ring.

When the memory is full, a new call automatically replaces

the oldest call in memory.

NEW

appears in the display for

calls received that have not been reviewed. REPT indicates

that a new call from the same number was received more

than once.

NOTE: Check with your local phone company

regarding name service availability.

REVIEWING RECORDS

As calls are received and stored, the display is updated to

let you know how many calls have been received.

•Press the CID/VOL (-) arrow button to scroll through the

call records from the most recent to the oldest.

•Press the CID/VOL (+) arrow button to scroll through the

call records from the oldest to the newest.

TRANSFERRING CID RECORDS TO

MEMORY

You may transfer a Caller ID record to your phone’s memory.

NOTE: It is important that you format CID records

correctly before storing in memory. It is not possible to

re-format CID records stored in memory.

1. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to

scroll to the desired record.

2. Press the memory button.

3. Press the desired memory location. You will hear a

confirmation tone. Example, press the number 1 key to

store the record in memory location 1.

To replace a CID record stored in a memory location

with a new CID record:

1. Repeat steps 1 through 3.

2. Press the memory button and REPLACE MEMO? shows

in the display.

3. Press *tone/cancel to exit, or press memory again and

the new CID record replaces the old CID record in that

memory location. You will hear a confirmation tone.

DELETING RECORDS

Use the channel/delete button to erase the record currently

shown in the display or all records.

DELETING THE CURRENT RECORD

1. Make sure the phone is OFF (not in TALK mode).

2. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to

display the desired Caller ID record.

3. Press channel/delete. The display shows DELETE?

4. Press channel/delete again to erase the record. You will

hear a confirmation tone. The display shows DELETED.

Then the next Caller ID record shows in the display.

DELETING ALL RECORDS

1. Make sure the phone is OFF (not in TALK mode).

2. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to

display any Caller ID record.

3. Press and hold channel/delete button until the unit

beeps and DELETE ALL?

shows in the display.

4. Press channel/delete again to erase all records. You will hear a

confirmation tone, and the display shows NO CALLS.

DIALING A CALLER ID NUMBER

1. Make sure the phone is OFF (not in TALK mode).

2. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to

display the desired Caller ID record.

3. Press TALK/callback button. The number dials

automatically.

CHANGING THE CID NUMBER FORMAT

The format button lets you change the format of the

displayed CID number. The available formats are as follows.

7-digit 7-digit telephone number.

10-digit 3-digit area code + 7-digit telephone number.

11-digit long distance code “1” + 3-digit area code +

7-digit telephone number.

1. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to

scroll to the number you want to call back.

2. If the number will not dial as shown, press the format

button. Repeat if necessary, until the correct number of

digits are shown.

3. Press TALK/callback button. The number dials

automatically.

MEMORY

Store up to 10 24-digit numbers in memory for quick

dialing. This memory feature is in addition to the 40 Caller

ID records that can be stored in the Caller ID memory log.

STORING A NAME AND NUMBER IN

MEMORY

1. Make sure the phone is OFF (not in TALK mode).

2. Press the memory button.

3. Press the desired memory location (0 through 9).

4. Press the memory button again. The display shows

ENTER NAME (up to 15 characters).

NOTE: If you don't want to enter the name, skip step 5.

For example, to enter the name Bill Smith, press the two

key twice for the letter B, press the four key three times

for the letter I, and press the five key three times for the

letter L. After one second, press the five key three times

again for the second letter L and press the one key to

insert a space between the letter L and S. Press the

seven key four times for the letter S, press the six key

once for the letter M, press the four key three times for

the letter I, press the eight key once for the letter T, and

press the four key twice for the letter H.

NOTE: If you enter a wrong letter, press channel/

delete button to backspace.

26934

40-Channel 900 MHz Caller ID with

Call Waiting Cordless Telephone

User's Guide

We bring good things to life.

ATLINKS USA, Inc.

101 West 103rd Street

Indianapolis, IN 46290

Trademark(s) ® Registered

Marca(s) ® Registrada(s)

Model 26934

16226400 (Rev. 0 DOM E)

03-19

Printed in China

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

CAUTION:

US NUMBER IS LOCATED ON THE CABINET BOTTOM

REN NUMBER IS LOCATED ON THE CABINET BOTTOM

TELEPHONE JACK REQUIREMENTS

To use this phone, you need an

RJ11C type modular telephone jack,

which might look like the one

pictured here, installed in your

home. If you don’t have a modular

jack, call your local phone company

to find out how to get one installed.

INSTALLATION NOTE: Some cordless telephones

operate at frequencies that may cause interference to

nearby TVs, microwave ovens, and VCRs. To minimize

or prevent such interference, the base of the cordless

telephone should not be placed near or on top of a

TV, microwave ovens, or VCR. If such interference

continues, move the cordless telephone farther away

from these appliances.

DIGITAL SECURITY SYSTEM

Your cordless phone uses a digital security system to

provide protection against false ringing, unauthorized

access, and charges to your phone line.

When you place the handset in the base, the unit verifies

its security code. After a power outage or battery

replacement, you should place the handset in the base for

about 20 seconds to reset the code.

in use/charge

page

CID/VOL

TALK

redial memory format

delete ringer

channel

off on

flash

abc

jkl

tuv

oper

def

mno

wxyz

ghi

pqrs

callback

program

tone

cancel

pause

Base Handset AC power

supply Telephone

line cord

CID/VOL

TALK

redial memory format

delete ringer

channel

off on

flash

abc

jkl

tuv

oper

def

mno

wxyz

ghi

pqrs

callback

program

tone

cancel

pause

CID/VOL

TALK

redial memory format

delete ringer

channel

off on

flash

abc

jkl

tuv

oper

def

mno

wxyz

ghi

pqrs

callback

program

tone

cancel

pause

CID/VOL

TALK

redial memory format

delete ringer

channel

off on

flash

abc

jkl

tuv

oper

def

mno

wxyz

ghi

pqrs

callback

program

tone

cancel

pause

redial

button

memory

button

channel/

delete

button ringer switch

left arrow/-

volume button right arrow/+

volume button

TALK/

callback

button

format

button

flash/

program

button

display

* tone/

cancel

button

# pause

button

NEW CALL #

Caller ID nameCaller ID phone number

Time Date New call

Belt Clip

EQUIPMENT APPROVAL INFORMATION

Your telephone equipment is approved for connection to the Public Switched Telephone

Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the

Technical Requirements for Telephone Terminal Equipment published by ACTA.

1Notification to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other information, the US

number and Ringer Equivalence Number (REN) for the equipment. You must, upon

request, provide this information to your telephone company.

The REN is useful in determining the number of devices you may connect to your

telephone line and still have all of these devices ring when your telephone number is

called. In most (but not all) areas, the sum of the RENs of all devices connected to one

line should not exceed 5. To be certain of the number of devices you may connect to

your line as determined by the REN, you should contact your local telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted

by the ACTA. A compliant telephone cord and modular plug is provided with this

product. It is designed to be connected to a compatible modular jack that is also

compliant. See installation instructions for details.

Notes

•This equipment may not be used on coin service provided by the telephone

company.

•Party lines are subject to state tariffs, and therefore, you may not be able to use

your own telephone equipment if you are on a party line. Check with your local

telephone company.

•Notice must be given to the telephone company upon permanent disconnection of

your telephone from your line.

•If your home has specially wired alarm equipment connected to the telephone line,

ensure the installation of this product does not disable your alarm equipment. If you

have questions about what will disable alarm equipment, consult your telephone

company or a qualified installer.

2Rights of the Telephone Company

Should your equipment cause trouble on your line which may harm the telephone network,

the telephone company shall, where practicable, notify you that temporary discontinuance

of service may be required. Where prior notice is not practicable and the circumstances

warrant such action, the telephone company may temporarily discontinue service

immediately. In case of such temporary discontinuance, the telephone company must: (1)

promptly notify you of such temporary discontinuance; (2) afford you the opportunity to

correct the situation; and (3) inform you of your right to bring a complaint to the Commission

pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.

The telephone company may make changes in its communications facilities, equipment,

operations or procedures where such action is required in the operation of its business and

not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the

use or performance of your telephone equipment, the telephone company must give you

adequate notice, in writing, to allow you to maintain uninterrupted service.

HEARING AID COMPATIBILITY (HAC)

This telephone system meets FCC standards for Hearing Aid Compatibility.

Modular

telephone

line jack

Wall plate

RECEIVING A CALL

1. Check the display to see who is calling.

2. Press the TALK button.

5. Press the memory button to save the name. The display

shows ENTER TEL NUMBR.

6. Use the number keypad to enter the telephone number

you want to store (up to 24 digits).

7. Press memory again to store the number. You will hear a

confirmation tone.

CHANGING A STORED NUMBER

1. Repeat steps 1 through 7 in Storing a Name and

Number in Memory.

2. Press the memory button and REPLACE MEMO? shows

in the display.

3. Press *tone/cancel to exit, or press the memory button

to store the number. You will hear a confirmation tone.

STORING A REDIAL NUMBER

1. Repeat steps 1 through 6 in Storing a Name and Number

in Memory.

2. Press the redial button.

3. Press the memory button to store the number. You will

hear a confirmation tone.

To replace an old redial number stored in a memory

locations with a new redial number:

1. Repeat steps 1 through 6 in Storing a Name and

Number in Memory.

2. Press the memory button and REPLACE MEMO? shows

in the display.

3. Press *tone/cancel to exit, or press the memory button

again and the new redial number replaces the old redial

number in that memory location. You will hear a

confirmation tone.

DIALING A STORED NUMBER

1. Make sure the phone is ON by pressing the TALK/

callback button.

2. Press memory button.

3. Press the number (0-9) for the desired memory location.

The number dials automatically.

- OR -

1. Make sure the phone is OFF (not in TALK mode).

2. Press memory button.

3. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to

scroll through the numbers stored in memory until the

desired number is shown.

4. Press TALK/callback. The numbers dial automatically.

IMPORTANT: If you make test calls to emergency

numbers stored in memory, remain on the line and

briefly explain the reason for the call to the dispatcher.

Also, it’s a good idea to make these calls in off-peak

hours, such as early morning or late evening.

INSERTING A PAUSE IN THE DIALING

SEQUENCE

When storing information in memory, press the # pause

button twice within one second to insert a delay in the

dialing sequence of a stored telephone number when a

pause is needed to wait for a dial tone (for example after

you dial 9 for an outside line, or to wait for a computer

access tone). PAUSE shows on the display as a

“

Each

pause counts as 1 digit in the dialing sequence.

REVIEWING AND DELETING STORED

NUMBERS

1. Press memory, then use the CID/VOL (-) arrow or CID/

VOL (+) arrow button to view the entry.

2. While the entry is displayed, press channel/delete button

to delete the entry. The display shows DELETE?

3. Press channel/delete again to delete the entry. DELETED

shows in the display.

CHAIN DIALING FROM MEMORY

Use this feature to make calls which require a sequence of

numbers such as using a calling card for a frequently

called long distance number. Basically, you dial each part

of the sequence from memory. The following example

shows how you can use chain dialing to make a call

through a long distance service:

The Number For Memory Location

Long distance access number 7

Authorization code 8

Frequently called long distance number 9

1. Make sure the phone is ON.

2. Press memory and then press 7.

3. When you hear the access tone, press memory again

and then press 8.

4. At the next access tone, press memory and then 9.

TIP: Wait for the access tones between pressing the

memory button, or your call might not go through.

HEADSET AND BELT CLIP

OPERATION

CONNECTING

AN OPTIONAL

HEADSET TO

THE HANDSET

For hands free

conversation, connect

the headset (optional)

to the HEADSET jack

as shown. The handset

receiver and

microphone are

disabled when the

headset is connected.

TIP: To order a headset, please refer to the accessory

order form at the end of this user’s guide.

Adjust the headset to

rest comfortably on top

of your head and over

your ear. Move the

microphone to

approximately 2 to 3

inches from your mouth.

•Press the TALK button

to answer or place a

call before using the headset.

CONNECTING THE BELT CLIP

There are two slots, one on each side of the handset.

•Attach the belt clip by inserting the sides of the belt clip

into the slots. Snap the ends of the belt clip into place.

CHANGING THE BATTERY

Make sure the telephone is OFF before

you replace battery.

1. Remove the battery compartment

door.

2. Disconnect the battery plug from the

jack in the handset battery

compartment and remove the battery

pack.

3. Insert the new battery pack and

connect the cord into the jack inside

the handset.

4. Put the battery compartment door

back on.

5. Place handset in the base to charge. Allow the handset

battery to properly charge (for 12 hours) prior to first use

or when you install a new battery pack. If you do not

properly charge the phone, battery performance will be

compromised.

CAUTION: To reduce the risk of fire or personal

injury, use only the battery 5-2461.

BATTERY SAFETY PRECAUTIONS

•Do not burn, disassemble, mutilate, or puncture. Like

other batteries of this type, toxic materials could be

released which can cause injury.

•To reduce the risk of fire or personal injury, use only the

battery listed in the User’s Guide.

•Keep batteries out of the reach of children.

•Remove batteries if storing over 30 days.

GENERAL PRODUCT CARE

To keep your telephone working and looking good, follow

these guidelines:

•Avoid putting the phone near heating appliances and

devices that generate electrical noise (for example,

motors or fluorescent lamps).

•DO NOT expose to direct sunlight or moisture.

•Avoid dropping and other rough treatment to the phone.

•Clean with a soft cloth.

•Never use a strong cleaning agent or abrasive powder

because this will damage the finish.

•Retain the original packaging in case you need to ship

the phone at a later date.

CAUSES OF POOR RECEPTION

•Aluminum siding.

•Foil backing on insulation.

•Heating ducts and other metal construction can shield

radio signals.

•You’re too close to appliances such as microwaves,

stoves, computers, etc.

•Atmospheric conditions, such as strong storms.

•Base is installed in the basement or lower floor of

the house.

•Base is plugged into an AC outlet with other

electronic devices.

•Baby monitor is using the same frequency.

•Handset battery is low.

•You’re out of range of the base.

DISPLAY MESSAGES

The following indicators show the status of a message or

of the unit.

INCOMPLETE DATA Caller information has been

interrupted during transmission or

the phone line is excessively noisy.

ENTER NAME Prompt telling you to enter the

name for one of the 10 memory

locations.

ENTER TEL NUMBR Prompt telling you to enter the

telephone number for one of the

10 memory locations.

DELETE? Prompt asking if you want to erase

Caller ID records or one of the 10

numbers stored in the phone’s

outgoing memory.

DELETE ALL? Prompt asking if you want to erase

all Caller ID records.

DELETED Prompt confirming the Caller ID /

Memory record is erased.

END OF LIST Indicates that there is no

additional information in Caller ID

memory.

NEW Indicates call or calls have not

been reviewed.

UNKNOWN NAME/ The incoming call is from

CALLER/NUMBER an area not serviced by Caller ID

or the information was not sent.

PAGING Someone has pressed the page

button on the base.

BLOCKED CALL The person is calling from a

number that has been blocked

from transmission.

BLOCKED NAME The person’s name is blocked

from transmission.

REPT Repeat call message. Indicates

that a new call from the same

number was received more than

once.

NO DATA No Caller ID information was

received.

EMPTY Indicates a memory location is

vacant.

NO CALLS Indicates no CID records have

been stored.

MESSAGE WAITING Indicates a message is available.

HANDSET SOUND SIGNALS

Signal Meaning

A long warbling tone Signals an incoming call

(with ringer on)

Two long beeps Confirmation Tone

One short and one long beep Page signal

One short beep Low battery warning

every seven seconds

TROUBLESHOOTING TIPS

CALLER ID

No Display

•Is battery fully charged? Try replacing the battery. Make

sure the battery is properly installed and connected.

•If you are using AC power, make sure that the unit is

connected to a non-switched electrical outlet.

Disconnect the unit from the plug and plug it in again.

•Did you order Caller ID service from your local

telephone company?

Caller ID Error Message

•The unit displays this message if it detects anything

other than valid Caller ID information during the silent

period after the first ring. This message indicates the

presence of noise on the line.

TELEPHONE

No dial tone

•Check installation:

— Is the base power cord connected to a working outlet?

— Is the telephone line cord connected to the base unit

and the wall jack?

•Disconnect the base from the wall jack and connect

another phone to the same jack. If there is no dial tone

in the second phone, the problem might be your wiring

or local service.

•Is the handset out of range of the base?

•Make sure the battery is properly charged (12 hours).

•Is the battery pack installed correctly?

•Did the handset beep when you pressed the TALK/

callback button? Did the display indicator turn on? The

battery may need to be charged.

Dial tone is OK, but can't dial out

• Make sure the tone/pulse setting is programmed

correctly.

Handset does not ring

•Make sure the ringer switch on the handset is turned

to ON.

•You may have too many extension phones on your line.

Try unplugging some phones.

•See solutions for “No dial tone.”

In use/charge indicator on the base flashes

•Provided your phone company offers voice messaging

service and you subscribe to it, the in use/charge

indicator on the base flashes when the phone is not in

use to indicate there is a message waiting. It stops

flashing after the message has been reviewed.

CUSTOMER: CUT ALONG DOTTED LINE. ✂

DESCRIPTION MODEL NO. TOTAL

QTY.

PRICE*

Belt clip $10.85

Headset $36.35

$9.95

Replacement battery

ACCESSORY ORDER FORM

5-2557

5-2601

5-2461

Please make sure that this form has been filled out completely.

To order, call 1-800-338-0376 (for accessories only) or

complete this order form.

Copy your complete account number from your

Master Card or Discover.

____________________________________________________________________

Authorized Signature

My card expires:

Copy the number above your

name on the Master Card.

For credit card purchases

Your complete charge card number, its expiration date and your

signature are necessary to process all charge card orders.

Copy your complete account number from your VISA card.

My card expires:

*Prices are subject to change without notice.

Total Merchandise.........................................$_______________

Sales Tax........................................................$_______________

We are required by law to collect the appropriate sales tax for each individual state,

county, and locality to which the merchandise is being sent. Duties will apply for

shipments to Canada.

Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.

currency only. No COD or Cash. All accessories are subject to availability. Where

applicable, we will ship a superseding model.

Shipping/Handling....................................... $_______________

Total Amount Enclosed.................................$_______________

Mail order form and money order or check (in U.S. currency)

made payable to Thomson to:

Thomson

Mail Order Department

P. O . Box 8419

Ronks, PA 17573-8419

Name_______________________________________________________

Address_____________________________________ Apt.____________

City ________________________State________ ZIP_________________

Daytime Phone Number ( )_______________________________

$5.00

$24.95

Power supply 5-2559

You experience static, noise, or fading in and out

•Change channels

•Is handset out of range? Move closer to the base.

•Does the base need to be relocated?

•Charge battery.

•Make sure base is not plugged into an outlet with

another household appliance.

Unit beeps

•Place handset in base for 20 seconds to reset the

security code. If that doesn’t work, charge battery for 12

hours.

•See solutions for “No dial tone.”

•Replace battery.

Memory Dialing

•Did you program the memory location keys correctly?

•Did you follow proper dialing sequence?

•Make sure the tone/pulse setting is programmed correctly.

•Did you reprogram numbers into memory after power

outage or battery replacement?

ERVICE

If trouble is experienced with this equipment, for repair or

warranty information, please contact customer service at

1-800-448-0329. If the equipment is causing harm to the

telephone network, the telephone company may request that

you disconnect the equipment until the problem is resolved.

This product may be serviced only by the manufacturer or

its authorized service agents. Changes or modifications not

expressly approved by ATLINKS USA, Inc. could void the

user’s authority to operate this product. For instructions on

how to obtain service, refer to the warranty included in this

guide or call customer service at 1-800-448-0329.

Or refer inquiries to:

ATLINKS USA, Inc.

Manager, Consumer Relations

P O Box 1976

Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference

or jot down the date this product was purchased or

received as a gift. This information will be valuable if

service should be required during the warranty period.

Purchase date _________________________________________

Name of store _________________________________________

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference; and (2)

This device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

•Reorient or relocate the receiving antenna (that is, the

antenna for radio or television that is “receiving” the

interference).

•Reorient or relocate and increase the separation

between the telecommunications equipment and

receiving antenna.

•Connect the telecommunications equipment into an

outlet on a circuit different from that to which the

receiving antenna is connected.

•Consult the dealer or an experienced radio/TV technician

for help.

If these measures do not eliminate the interference, please

consult your dealer or an experienced radio/television

technician for additional suggestions. Also, the Federal

Communications Commission has prepared a helpful

booklet, “How To Identify and Resolve Radio/TV

Interference Problems.” This booklet is available from the

U.S. Government Printing Office, Washington, D.C. 20402.

Please specify stock number 004-000-00345-4 when

ordering copies.

LIMITED WARRANTY

What your warranty covers:

•Defects in materials or workmanship.

For how long after your purchase:

•One year, from date of purchase.

(The warranty period for rental units begins with the

first rental or 45 days from date of shipment to the

rental firm, whichever comes first.)

What we will do:

•Provide you with a new or, at our option, a refurbished

unit. The exchange unit is under warranty for the

remainder of the original product’s warranty period.

How you get service:

•Properly pack your unit. Include any cables, etc., which

were originally provided with the product. We

recommend using the original carton and packing

materials.

•”Proof of purchase in the form of a bill of sale or

receipted invoice which is evidence that the product is

within the warranty period, must be presented to obtain

warranty service.” For rental firms, proof of first rental

is also required. Also print your name and address and

a description of the defect. Send via standard UPS or its

equivalent to:

ATLINKS USA, Inc.

c/o Thomson

11721 B Alameda Ave.

Socorro, Texas 79927

•Pay any charges billed to you by the Exchange Center

for service not covered by the warranty.

•Insure your shipment for loss or damage. ATLINKS

accepts no liability in case of damage or loss.

•A new or refurbished unit will be shipped to you freight

prepaid.

What your warranty

does not

cover:

•Customer instruction. (Your Owner’s Manual provides

information regarding operating instructions and user

controls. Any additional information, should be

obtained from your dealer.)

•Installation and setup service adjustments.

•Batteries.

•Damage from misuse or neglect.

•Products which have been modified or incorporated

into other products.

•Products purchased or serviced outside the USA.

•Acts of nature, such as but not limited to lightning

damage.

Product Registration:

•Please complete and mail the Product Registration Card

packed with your unit. It will make it easier to contact

you should it ever be necessary. The return of the card

is not required for warranty coverage.

Limitation of Warranty:

•THE WARRANTY STATED ABOVE IS THE ONLY

WARRANTY APPLICABLE TO THIS PRODUCT. ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR

WRITTEN INFORMATION GIVEN BY ATLINKS USA,

INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A

GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF

THIS WARRANTY.

•REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE EXCLUSIVE REMEDY OF THE

CONSUMER. ATLINKS USA, INC. SHALL NOT BE

LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS

PRODUCT OR ARISING OUT OF ANY BREACH OF ANY

EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.

THIS DISCLAIMER OF WARRANTIES AND LIMITED

WARRANTY ARE GOVERNED BY THE LAWS OF THE

Headset jack

Headset plug

Slot for

belt clip

Slot for

belt clip

black white

5-2556

n/a

5-2461

5-2558

NOTE: The RBRC seal on the battery

used in your ATLINKS USA, Inc.

product indicates that we are

participating in a program to collect

and recycle Nickel Cadmium batteries

throughout the United States. Please

call 1-800-8-BATTERY for information

or contact your local recycling center.

Ni-Cd

RBRC

STATE OF INDIANA. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED

TO THE APPLICABLE WARRANTY PERIOD SET FORTH

ABOVE.

How state law relates to this warranty:

•Some states do not allow the exclusion nor limitation of

incidental or consequential damages, or limitations on

how long an implied warranty lasts so the above

limitations or exclusions may not apply to you.

•This warranty gives you specific legal rights, and you

also may have other rights that vary from state to state.

If you purchased your product outside the USA:

•This warranty does not apply. Contact your dealer for

warranty information.

Ge Appliances 26934 Users Manual

26934 to the manual 6f1525af-8944-4517-acf2-ab027cd3b295

Navigation menu

Versions of this User Manual:

Views

Navigation