Ge Appliances Edw4000 Users Manual 49 55031

EDW5000 Dispatcher?RequestType=PDF&Name=49-55031

GLD6000 to the manual 0a5043dd-676e-4791-8242-959720b09973

: Ge-Appliances Ge-Appliances-Edw4000-Users-Manual-254229 ge-appliances-edw4000-users-manual-254229 ge-appliances pdf

Open the PDF directly: View PDF .
Page Count: 16

EDW4000 Series

EDW5000 Series

EDW6000 Series

GHDA400 Series

GHDA600 Series

GLD4000 Series

GLD5000 Series

GLD6000 Series

HLD4000 Series

Owner’s Manual

Dishwashers

165D4700P350 49-55031 03-07 JR

Safety Instructions . . . . . . 2, 3

Operating Instructions

Care and Cleaning . . . . . . . . . . . . 12

Control Panel and Settings . . . 4–7

Loading Place Settings . . . . . . . . 11

Loading the Racks . . . . . . . . . . . . 10

Optional Accessories . . . . . . . . . .11

Using the Dishwasher . . . . . . . .8, 9

Troubleshooting Tips . . 13, 14

Consumer Support

Consumer Support . . . . .Back Cover

Warranty . . . . . . . . . . . . . . . . . . . . 15

ge.com

Write the model and serial

numbers here:

Model # __________________

Serial # __________________

You can find them on the tub wall

just inside the door.

2

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING —

SAVE THESE INSTRUCTIONS

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire

or explosion, electric shock, and to prevent property damage, personal injury, or death.

WATER HEATER SAFETY

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation

Instructions before it is used. If you did not receive an Installation Instructions sheet with

your dishwasher, you can receive one by visiting our website at ge.com.

■Contents washed in Anti-bacterial mode, if

available, may be hot to the touch. Use care

before handling.

■Using a detergent that is

not specifically designed

for dishwashers will cause

the dishwasher to fill with

suds.

■If your dishwasher is connected to a

wall switch, ensure that the switch is

on prior to use.

■On dishwashers with electronic controls,

if you choose to turn the switch off

between wash cycles, allow 5-10

seconds after turning the switch on before

touching START/RESET to allow the control to

reboot.

■Non-Dishware Items: Do not wash items such

as electronic air cleaner filters, furnace filters and

paint brushes in your dishwasher. Damage to

dishwasher and discoloration or staining of

dishwasher may result.

■Close supervision is necessary if this appliance

is used by or near children.

■Load light, plastic items so they will not

become dislodged and drop to the bottom

of the dishwasher—they might come into

contact with the heating element and be

damaged.

■Connect to a grounded metal, permanent wiring

system; or run an equipment-grounding

conductor with the circuit conductors and

connect to the equipment-grounding terminal

or lead of the appliance.

■Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

■Dispose of discarded appliances and shipping

or packing material properly.

■Do not attempt to repair or replace any part

of your dishwasher unless it is specifically

recommended in this manual. All other servicing

should be referred to a qualified technician.

■To minimize the possibility of electric shock,

disconnect this appliance from the power supply

before attempting any maintenance.

NOTE: Turning the dishwasher off does not

disconnect the appliance from the power supply.

We recommend having a qualified technician

service your appliance.

WARNING!

CAUTION: To prevent minor injury or property damage

Under certain conditions hydrogen gas may be produced in a water heater that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury

by turning on all hot water faucets and allow them to run for several minutes. Do this before using any

electrical appliance which is connected to the hot water system. This simple procedure will allow any built-

up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance

during this process.

3

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are

dangerous…even if they will sit for “just a

few days.” If you are getting rid of your old

dishwasher, please follow the instructions

below to help prevent accidents.

Before You Throw Away Your Old

Dishwasher:

■Take off the door of the washing compartment

or remove the door latch keeper (as shown).

WARNING! RISK OF CHILD ENTRAPMENT

Door latch keeper

READ AND FOLLOW THIS SAFETY INFORMATION

CAREFULLY.

SAVE THESE INSTRUCTIONS

■Use this appliance only for its intended purpose

as described in this Owner's Manual.

■Use only powder, tabs, liquid detergents or rinse

agents recommended for use in a dishwasher and

keep them out of the reach of children. Cascade®,

Cascade®Complete and Electrasol®Automatic

Dishwashing Detergents, and Jet-Dry®and

Cascade Rinse Aid®rinse agents have been

approved for use in all GE dishwashers.

■Locate sharp items so that they are not likely

to damage the door seal.

■Load sharp knives with the handles up to reduce

the risk of cut-type injuries.

■Do not wash plastic items unless marked

dishwasher safe or the equivalent. For plastic

items not so marked, check the manufacturer's

recommendations.

■Do not touch the heating element during or

immediately after use.

■Do not operate your dishwasher unless all

enclosure panels are properly in place.

■Do not tamper with controls.

■Do not abuse, sit on or stand on the door or dish

rack of the dishwasher.

■Do not allow children to play around dishwasher

when opening or closing door due to the possibility

of small fingers being pinched in door.

■Do not discard a dishwasher without first removing

the door of the washing compartment.

■Do not store or use combustible materials, gasoline

or other flammable vapors and liquids in the

vicinity of this or any other appliance.

■Do not allow children to play with, on or inside this

appliance or any discarded appliance.

WARNING! When using your dishwasher, follow basic precautions,

including the following:

4

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

About the dishwasher control panel. (For models with sensor: EDW6000 Series,

GHDA600 Series, GLD6000 Series)

You can locate your model number on the tub wall just inside the door.

Throughout this manual, features and

appearance may vary from your model.

Control Settings

Status Indicator Lights

The Status display tells you what’s happening while the dishwasher is in operation and may flash, indicating a

malfunction (see page 8). The lights will come ON indicating the sequence of operation the dishwasher is in.

SENSING Displayed while the sensor is measuring the amount of soil and temperature of water.

(on some models) The dishwasher will adjust the selected cycle to achieve optimal performance.

WASHING Displayed during prewash and main wash periods.

(on some models)

RINSING Displayed during rinse periods.

(on some models)

DRYING Displayed during HEATED DRY.

(on some models)

SANITIZED Displayed when cycle has met sanitization conditions. Light remains ON until door is opened.

CLEAN Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are

clean until the door is relatched or until another cycle is selected.

Time Remaining Display (on some models)

During operation, the display shows the minutes remaining until the cycle is complete. The display may adjust the

remaining time while the sensing light is on. The time displayed at the start of each cycle may change from the

factory setting as the unit customizes itself to home use. During a delay start, the display will show hours of time

remaining until the cycle starts.

Cycles

The light above the selected pad will be ON to indicate which cycle has been selected.

This dishwasher is equipped with a dirt and temperature sensor. Cycle length and time will vary depending on the

soil level and temperature.

ANTI-BACTERIA Heavy 8.5 gal., 84 min.

or SANI WASH Medium 7.3 gal., 78 min.

Light 6.1 gal., 75 min.

This cycle raises the water temperature in the final rinse to sanitize your dishware. The cycle

length will vary depending on the temperature of your inlet water.

NOTE: The Anti-Bacteria cycle is monitored for sanitization requirements. If the cycle is

interrupted during or after the main wash portion or if the incoming water temperature is so low

that adequate water heating cannot be achieved, the sanitizing conditions may not be met. In

these cases, the sanitized light will not illuminate at the end of the cycle.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

POTS Heavy 10.9 gal., 102 min.

& PANS Medium 8.5 gal., 78 min.

Light 7.3 gal., 73 min.

This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-on soils.

Everyday dishes are safe to be used in this cycle.

NORMAL WASH Heavy 8.5 gal., 65 min.

Medium 7.3 gal., 60 min.

Light 4.9 gal., 49 min.

This cycle is for medium/heavily soiled dishes and glassware

.

1

1

53 2

3

2

4

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

SPEED CYCLE 7.3 gal., 35 min.

or This cycle is for everyday dishes and glassware.

SPEED WASH

(on some models)

CHINA CRYSTAL 7.3 gal., 48 min.

(on some models) This cycle is for lightly soiled china and crystal.

RINSE ONLY 2.5 gal., 12 min.

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

NOTE: Only the Anti-Bacteria cycle has been designed to meet the requirements of Section 6, NSF 184 for

soil removal and sanitization efficacy.

Options

The light above the selected pad will be ON to indicate which option has been selected.

PRE SCRUB For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected PRIOR to

(on some models) starting the cycle. This option adds 16 minutes to the cycle time. NOTE: Cannot be selected with

RINSE ONLY cycle.

HEATED DRY Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry,

Light OFF you can prop the door open after the CLEAN light illuminates.

HEATED DRY Turns the heater on for fast drying. This will extend the total run time by 8 minutes for the SPEED

Light ON CYCLE, 38 minutes for NORMAL and POTS/PANS, and 30 minutes for all other cycles.

NOTE: Cannot be selected with RINSE ONLY cycle.

LOCK You can lock the controls to prevent any selections from being made. Or you can lock the controls

after you have started a cycle.

Children cannot accidentally start dishwasher by touching pads with this option selected.

To LOCK the dishwasher control, touch and hold the HEATED DRY pad for 3 seconds. The light

below the HEATED DRY pad will turn on. To UNLOCK the dishwasher control, touch and hold the

HEATED DRY pad for 3 seconds. The LOCK light will turn off.

ADDED When selected, the cycle will run longer with the heating element on to improve both wash and

HEAT dry performance. NOTE: Cannot be selected with RINSE ONLY cycle.

DELAY HOURS You can delay the start of a wash cycle for up to 9 hours. Touch the DELAY HOURS pad to choose

the number of hours you want to delay the start of the cycle; then touch START/RESET one time.

The dishwasher will count down and start automatically at the correct time. Touching

START/RESET a second time will cancel the DELAY START selection.

RESET To change a cycle after washing starts, touch the START/RESET pad to cancel the cycle. The

START/RESET light will flash while the water is pumped out if needed. This takes approximately

90 seconds. When the light stops flashing, the dishwasher can be reprogrammed and restarted.

Start

Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the START/RESET pad

once to begin the cycle. Water begins to fill the dishwasher, and approximately 60 seconds later the wash action

begins. Touching the START/RESET pad a second time will cancel the cycle and cause the water to drain out. This will

take approximately 2 minutes.

NOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher

door is fully closed, the control panel lights will display the last settings you selected.

If you don’t want to change any of the settings, simply touch the START/RESET pad once to begin the cycle.

If the door is closed, the indicator lights will turn off if the START/RESET pad is not pressed within two minutes.

To activate the display, open and close the door or touch any pad.

Also, if a power failure occurs, NORMAL and HEATED DRY will automatically be programmed.

4

ge.com

5

5

6

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

About the dishwasher control panel. (For models without a sensor: EDW4000 Series,

EDW5000 Series, GHDA400 Series, GLD4000 Series, GLD5000 Series and HLD4000 Series)

You can locate your model number on the tub wall just inside the door.

Throughout this manual, features and

appearance may vary from your model.

Control Settings

Status Indicator Lights

The Status display tells you what’s happening while the dishwasher is in operation and may flash,

indicating a malfunction (see page 8). The lights will come ON indicating the sequence

of operation the dishwasher is in.

SANITIZED Displayed when cycle has met sanitization conditions. Light remains ON until

(on some door is opened.

models)

CLEAN Displayed when a wash cycle is complete. The light stays ON as a reminder that

(on some the dishes are clean until the door is opened or until another cycle is selected.

models)

Cycles

The light above the selected pad will be ON to indicate which cycle has been selected.

SANI WASH 7.3 gal., 97 min.

(on some This cycle raises the water temperature in the final rinse to sanitize your dishware.

models) The cycle length will vary depending on the temperature of your inlet water.

NOTE: The SANI-WASH cycle is monitored for sanitization requirements. If the

cycle is interrupted during or after the main wash portion or if the incoming water

temperature is so low that adequate water heating cannot be achieved, the

sanitizing conditions may not be met. In these cases, the sanitized light will not

illuminate at the end of the cycle.

NOTE: NSF certified residential dishwashers are not intended for licensed food

establishments.

POTS & PANS 8.5 gal., 89 min.

or HEAVY This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-

WASH on soils. Everyday dishes are safe to be used in this cycle.

NORMAL WASH 5.9 gal., 56 min.

This cycle is for medium/heavily soiled dishes and glassware.

LIGHT WASH 6.1 gal., 36 min.

(on some This cycle is for everyday dishes and glassware.

models)

CHINA CRYSTAL 6.1 gal., 39 min.

(on some This cycle is for lightly soiled china and crystal.

models)

RINSE ONLY 1.2 gal., 6 min.

For rinsing partial loads that will be washed later. Do not use detergent with

this cycle.

NOTE: Only the SANI-WASH cycle has been designed to meet the requirements of Section 6,

NSF 184 for soil removal and sanitization efficacy.

1

1

3

4

2

2

7

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Options

The light above the selected pad will be ON to indicate which OPTION has been selected.

HOT START For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be

(on some selected PRIOR to starting the cycle. This option will improve both wash and dry

models) performance. This option adds 20 minutes to the cycle time.

NOTE: Cannot be selected with RINSE ONLY cycle.

HEATED DRY Shuts off the drying heat option. Dishes air dry naturally and energy is saved.

Light OFF For faster air dry you can prop the door open after the CLEAN light illuminates.

HEATED DRY Turns the heater on for fast drying. This will extend the total run time by 38 minutes.

Light ON NOTE: Cannot be selected with RINSE ONLY cycle.

LOCK You can lock the controls to prevent any selections from being made. Or you can lock

the controls after you have started a cycle.

(on some Children cannot accidentally start dishwasher by touching pads with this option

models) selected.

To LOCK the dishwasher control, touch and hold the HEATED DRY pad for 3 seconds. The light below

the HEATED DRY pad will turn on. To UNLOCK the dishwasher control, touch and hold the HEATED

DRY pad for 3 seconds. The LOCK light will turn off.

HOT WASH When selected, the cycle will run longer with the heating element on to improve both

wash and dry performance. NOTE: Cannot be selected with RINSE ONLY cycle.

DELAY HOURS You can delay the start of a wash cycle for 2, 4 or 8 hours (delay time options may

vary by model). Touch the DELAY HOURS pad to choose the number of hours you want

to delay the start of the cycle; then touch START/RESET one time. The dishwasher will

count down and start automatically at the correct time. Touching START/RESET a

second time will cancel the DELAY START selection.

RESET To change a cycle after washing starts, touch the START/RESET pad to cancel the

cycle. The START/RESET light will flash while the water is pumped out if needed. This

takes approximately 90 seconds. When the light stops flashing, the dishwasher can be

reprogrammed and restarted.

Start

Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the

START/RESET pad once to begin the cycle. Water begins to fill the dishwasher, and approximately 60

seconds later the wash action begins. Touching the START/RESET pad a second time will cancel the

cycle and cause the water to drain out. This will take approximately 2 minutes.

NOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When

the dishwasher door is fully closed, the control panel lights will display the last settings you selected.

If you don’t want to change any of the settings, simply touch the START/RESET pad once to begin

the cycle.

If the door is closed, the indicator lights will turn off if the START/RESET pad is not pressed within two

minutes. To activate the display, open and close the door or touch any pad.

Also, if a power failure occurs, NORMAL and HEATED DRY will automatically be programmed.

3

ge.com

4

Dish Preparation Prior to Loading

■No pre-rinsing of normal food soil is required.

■Scrape off hard soils, including bones,

toothpicks, skins and seeds.

■Remove large quantities of any remaining

food.

■Remove leafy vegetables, meat trimmings

and excessive amounts of grease or oil.

■Remove acidic food soils that can discolor

stainless steel.

8

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

Using the dishwasher.

Check the Water Temperature

Use Jet-Dry®or Cascade Crystal Clear®Rinse Agent

Jet-Dry®or Cascade Crystal Clear®rinse agents remove spots and prevent new film buildup on

your dishes, glasses, flatware, cookware and plastic.

Filling the Dispenser

The rinse agent dispenser holds 100 ml (3.5 fl. oz.) of rinse agent. Under

normal conditions, this will last approximately one month. Try to keep it

full, but do not overfill.

Make sure the dishwasher door is fully open.

Turn the dispenser cap to the left and lift it out.

Add rinse agent until the indicator window looks full.

Clean up any spilled rinse agent with a damp cloth.

Replace the dispenser cap.

Rinse Aid Setting

The amount of rinse agent released into the final wash can be adjusted.

The factory setting is at the midpoint. If there are rings of calcium (hard

water) spots on dishes, try a higher setting. If you see foam in the

dishwasher, move the indicator to a lower setting.

To adjust the setting

Remove the dispenser cap; then turn the adjuster counterclockwise to

increase the amount of rinse agent, clockwise to reduce the amount of rinse agent.

5

4

3

2

1

The entering water should be at least 120°F

and not more than 150°F, for effective cleaning

and to prevent dish damage. Check the water

temperature with a candy or meat thermometer.

Turn on the hot water faucet nearest the

dishwasher, place the thermometer in a glass

and let the water run continuously into the

glass until the temperature stops rising.

Indicator

window Dispenser cap

Rinse

agent

adjuster

Use only detergent specifically made for use

in dishwashers. Cascade®and Electrasol®

Automatic Dishwashing Detergents have been

approved for use in all GE dishwashers. Keep

your detergent fresh and dry. Don’t put powder

detergent into the dispenser until you’re ready

to wash dishes.

The amount of detergent to use depends on

whether your water is hard or soft. With hard

water, you need extra detergent. With soft water,

you need less detergent.

Protect your dishes and dishwasher by

contacting your water department and asking

how hard your water is. Twelve or more grains

is extremely hard water. A water softener is

recommended. Without it, lime can build up

in the water valve, which could stick while open

and cause flooding. Too much detergent with

soft water can cause a permanent cloudiness

of glassware, called etching.

Use the information in the table below as a

guideline to determine the amount of automatic

dishwasher detergent to place in the dispenser.

For heavily-soiled loads, use the Pots and Pans or

Heavy Wash cycle and add a little extra detergent.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically

designed for dishwashers will cause the dishwasher

to fill with suds. During operation, these suds will spill

out of the dishwasher vents, covering the kitchen

floor and making the floor wet.

Because so many detergent containers look alike,

store the dishwasher detergent in a separate space

from all other cleaners. Show anyone who may use

the dishwasher the correct detergent and where

it is stored.

While there will be no lasting damage to the

dishwasher, your dishes will not get clean using a

dishwashing detergent that is not formulated to

work with dishwashers.

MAIN WASH

PRE

WASH

Soft

Medium

Soft

Medium

Hard

Extremely

Hard

A forgotten dish can be added any time before

the main wash.

Squeeze the door latch to release the door.

Do not open the door until the water spray

action stops. Steam may rise out of the

dishwasher.

Add forgotten dishes.

Close the door.

4

3

2

1

9

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Using the dishwasher. ge.com

Proper Use of Detergent

Forget to Add a Dish?

Detergent Cups to Fill

Fill cup to first line

Fill cup to second line

Fill main wash cup

Fill both Main Wash and

Pre Wash cup

Number

of Grains

Less than 4

4 to 8

8 to 12

Greater

than 12

10

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

Loading the dishwasher racks.

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack

Although the upper rack is for glasses, cups and

saucers, pots and pans can be placed in this rack

for effective cleaning. Cups and glasses fit best

along the sides. This is also a secure place for

dishwasher-safe plastics.

The utility shelf (on some models) may be placed in

the up or down position to add flexibility. A wine

glass holder (on some models) secures wine

glasses for best washability. Because wine glasses

come in various sizes, after loading, slowly push

in the rack to make sure they will clear the top of

the dishwasher.

The upper rack is good for all kinds of odd-shaped

utensils. Saucepans, mixing bowls and other items

should be placed face down. Fold-down tines (on

some models) provide flexibility for extra-large and

hard-to-fit items.

Secure larger dishwasher-safe plastics over 2 tines

when possible.

Make sure small plastic items are secure so they

can’t fall onto the heater.

Be sure that items do not protrude through

the bottom of the rack and block rotation of the

middle spray arm. This could result in poor wash

performance for items in the upper rack.

Check to make

sure that no items

will block rotation

of the wash arms.

Lower Rack

The lower rack is best used for plates, saucers and

cookware. Large items such as broiler pans and

baking racks should go along the left-hand side.

Load platters, pots and bowls along the sides, in

corners or in the back. The soiled side of items

should face the center of the rack. If necessary,

oversized glasses and mugs can be placed in the

lower rack to maximize loading flexibility.

Also, be careful not to let a portion of an item such

as a pot or dish handle extend through the bottom

rack. This could block the wash arm and cause

poor washing results.

Fold-down tines (on some models) provide

flexibility for extra-large and hard-to-fit items. The

tines may be left in the up position or folded down

to customize the lower rack.

Do not let any item

extend through the

bottom of the silverware

basket. Items that

extend through the rack

could prevent the spray

arm from turning and

cause poor wash

performance.

Silverware Basket

To load flatware, simply push the adjustable

handle to either side (on some models). Put

flatware in the removable basket with fork and

knife handles up to protect your hands. Place

spoons in the basket with handles down. Mix

knives, forks and spoons so they don’t nest

together. Distribute evenly. Small plastic items,

such as measuring spoons and lids from small

containers should go in the bottom of the

silverware basket with the silverware on top.

The one-piece silverware basket (on some models)

can be placed in the front, right side or back of the

lower rack.

A variety of options is available regarding the

three-piece silverware basket (on some models)

in your dishwasher. The complete basket is

designed to fit on the right side of the lower rack.

Additionally, each end of the basket is removable

to add loading flexibility to accommodate flatware

and lower rack capacity needs.

The lids of both end and middle baskets

(on some models) can be closed to contain small

items. Long items can be placed on the utility shelf

in the upper rack.

The accessory

basket (on some

models) can hold

small items such

as: baby bottle

nipples, plastic lids,

corn cob holders, etc.

To remove end baskets, grasp the

basket at opposite corners and slide

apart.

Three-piece basket (on some models)

One-piece basket (on some models)

Single basket (on some models)

11

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Follow these guidelines for loading 10 place settings. Features and appearance of racks and silverware baskets

may vary from your model.

Upper Rack—10 place settings Lower Rack—10 place settings Lower Rack—10 place settings

Follow these guidelines for loading 12 place settings. Features and appearance of racks and silverware baskets

may vary from your model.

Upper Rack—12 place settings Lower Rack—12 place settings

You can change the appearance of your

dishwasher by adding a custom panel trim kit.

Wood panel trim kit—This accessory contains

trim and instructions for you to supply and install

a 1/4″thick decorative wood door:

■GPF525B (Black)

■GPF525W (White)

■GPF525C (Bisque)

Trimless wood panel kit—This accessory

contains parts and instructions for you to supply

and install a 3/4″thick decorative wood door:

■GPF575

Non-wood countertop bracket kit—This is for

installations which have non-wood countertops

and includes side-mounting brackets and

instructions for securing the dishwasher.

■GPF65

These accessories are available at extra cost from

GE. Call 800.626.2002 to order. Visa, Mastercard

or Discover cards are accepted.

Specify accessory number when ordering.

Optional accessories.

Loading place settings… ge.com

12

If your dishwasher is left in an unheated

place during the winter, ask a service

technician to:

Cut off electrical power to the

dishwasher. Remove fuses or trip

circuit breaker.

Turn off the water supply and

disconnect the water inlet line from

the water valve.

Drain water from the water inlet line

and water valve. (Use a pan to catch

the water.)

Reconnect the water inlet line to the

water valve.

4

3

2

1

Caring for the dishwasher.

Cleaning the Door Panel

Before cleaning the front panel, make sure

you know what type of panel you have.

Refer to the last two letters of your model

number. You can locate your model

number on the left-hand tub wall just

inside the door. If your model number ends

with BB, WW, CC, SA or BG, then you have

a Painted Door panel. If your model

number ends with SS, then you have a

Stainless Steel Door panel. If your model

number ends with CS, then you have a

CleanSteel Door panel.

Follow the instructions below for cleaning

the door panel for your specific model.

Painted Door Panel (model numbers

ending in BB–black, WW–white, CC–bisque,

SA–silver metallic, BG–graphite metallic or

GS–silver)

Use a clean, soft, lightly dampened cloth,

then dry thoroughly. You may also use a

good appliance wax or polish.

Stainless Steel Door Panel (model

numbers ending in SS)

The stainless steel panels can be cleaned

with Stainless Steel Magic or a similar

product using a clean, soft cloth. Do not

use appliance wax, polish, bleach or

products containing chlorine on Stainless

Steel doors.

You can order Stainless Steel Magic

#WX10X15 through GE Parts by calling

800.626.2002.

CleanSteel Door Panel (model numbers

ending in CS)

Use a clean, soft, lightly dampened cloth,

then dry thoroughly. Do not use appliance

wax, polish or any chemical agent on

CleanSteel doors.

Do not wipe the dishwasher with a soiled

dish cloth or wet towel. These may leave

a residue. Do not use scouring pads or

powdered cleaners because these

products can scratch the finish.

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

Cleaning the Control Panel

To clean the control panel, use a lightly

dampened cloth. Then dry thoroughly.

Protect Against Freezing

Check the air gap any time

your dishwasher isn’t draining

well.

An air gap protects your dishwasher

against water backing up into it if a drain

clogs. The air gap is not a part of the

dishwasher. It is not covered by your

warranty. Not all plumbing codes require

air gaps, so you may not have one.

The air gap is easy to clean.

Turn off the dishwasher and lift off the

cover.

Remove the plastic cap and clean with

a toothpick.

2

1

Air gap Does Your Dishwasher Have an Air Gap?

Problem Possible Causes What To Do

Dishes and flatware Low inlet water temperature • Make sure inlet water temperature is correct (see page 8). Turn on

not clean the hot water faucet nearest the dishwasher, let run until the water

temperature stops rising. Then start the dishwasher and turn off

the faucet. This insures the entering water is hot.

Water pressure is temporarily low • Turn on a faucet. Is water coming out more slowly than usual?

If so, wait until pressure is normal before using your dishwasher.

Air gap or disposer is clogged • Clean the air gap or flush the disposer.

Improper rack loading • Make sure large dishware does not block the detergent dispenser

or the wash arms. See the Loading the dishwasher racks section.

No air gap or high drain loop • Verify that you have an air gap or a high drain loop. Refer to

the Installation Instructions.

Spots and filming •Use Jet-Dry ®or Cascade Crystal Clear®rinse agents to remove spots and

on glasses and prevent new film buildup.

flatware •To remove stubborn spots and pre-existing film from glassware:

1Remove all metal utensils from the dishwasher.

2Do not add detergent.

3Select the POTS & PANS or HEAVY WASH cycle.

4Start the dishwasher and allow to run for 18 to 22 minutes. Dishwasher

will now be in the main wash.

5Open the door and pour 2 cups (500 ml) of white vinegar into the

bottom of the dishwasher.

6Close the door and allow to complete the cycle. If vinegar rinse doesn’t

work: Repeat as above, except use 1/4 cup (60 ml) of citric acid crystals

instead of vinegar.

Cloudiness on Combination of soft water and • This is called etching and is permanent. To prevent this from happening,

glassware too much detergent use less detergent if you have soft water. Wash glassware in the shortest

cycle that will get them clean.

Water temperature entering • This could be etching. Lower the water heater temperature.

the dishwasher exceeds 150°F

Suds in the tub Wrong detergent • Use only automatic dishwasher detergents to avoid sudsing.

Cascade®and Electrasol®Automatic Dishwashing Detergents

have been approved for use in all GE dishwashers.

•To remove suds from the tub, open the dishwasher and let

suds dissipate. Close and latch the dishwasher. Pump out water

by touching the START/RESET pad once; then 30 seconds later,

touch the START/RESET pad again. Repeat if necessary.

Rinse agent was spilled • Always wipe up rinse agent spills immediately.

Error Messages Possible Causes What To Do

START/RESET status You have pressed the • Press the START/RESET pad only when you want to restart the

indicator light flashing START/RESET pad while the dishwasher.

dishwasher is running. This will

cancel the cycle. The light will stop

flashing after the dishwasher drains

(about 90 seconds).

Dishwasher BEEPS This is a reminder that your • Close and latch the door after opening it mid-cycle.

once every 30 seconds dishwasher door has been left

open during operation. It will

continue beeping until you close

the door.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions

Before you call for service… ge.com

Troubleshooting Tips

Save time and money! Review the charts on the following

pages, or visit ge.com. You may not need to call for service.

13

Extremely hard water

Low inlet water temperature

Overloading the dishwasher

Improper loading

Old or damp powder detergent

Rinse agent dispenser empty

Too little detergent

Operating Instructions Safety Instructions

Consumer Support Troubleshooting Tips

Before you call for service…

14

Problem Possible Causes What To Do

Detergent left in Dishes are blocking the • Reposition the dishes, so the water from the lower spray arm can

dispenser cups detergent cup flush the detergent cup. See the Loading the dishwasher section.

Black or gray Aluminum utensils have • Remove marks with a mild, abrasive cleaner.

marks on dishes rubbed against dishes

Dishes don’t dry Low inlet water temperature • Make sure inlet water temperature is at least 120°F.

•Select HEATED DRY.

•Use HOT START, HOT WASH or ADDED HEAT options.

•Select a higher cycle, such as ANTI-BACTERIA, SANI WASH, POTS & PANS

or HEAVY WASH.

Rinse agent dispenser is empty • Check the rinse agent dispenser and fill as required.

Control panel responded Door latch may not be properly • Make sure the door is firmly closed.

to inputs but dishwasher seated

never filled with water Water valve may be turned off • Make sure water valve (usually located under the sink) is turned on.

Stained tub interior Some tomato-based foods can • Use of the RINSE ONLY cycle after adding the dish to the load

cause reddish stains can decrease the level of staining. GE recommends Cascade®

Plastic Booster to help remove these types of stains.

Tea or coffee stains • Remove the stain by hand, using a solution of 1/2 cup bleach

and 3 cups warm water.

WARNING

Before cleaning interior, wait at least 20 minutes after a cycle for the

heating elements to cool down. Failure to do so can result in burns.

An overall yellow or brown film can

•A special filter in the water supply line is the only way to correct

be caused by iron deposits in water

this problem. Contact a water softener company.

White film on inside surface— • GE recommends Jet-Dry ®or Cascade Crystal Clear®to help

hard water minerals prevent hard water mineral deposits from forming.

•Run dishwasher with citric acid to remove mineral deposits. Citric acid

(Part number: WD35X151) can be ordered through GE Parts. See back

cover for ordering information.

Dishwasher won’t run Fuse is blown or circuit breaker • Replace fuse or reset circuit breaker. Remove any other appliances from

is tripped the circuit.

Power is turned off • In some installations, the power to the dishwasher is provided through a

wall switch, often located next to the disposer switch. Make sure it is on.

Control panel is locked • Unlock control panel. See page 5 or 7.

Reboot your control • Turn off power to the dishwasher (circuit breaker or wall switch) for

30 seconds; then turn back on.

Control panel lights Time too long between • Each pad must be touched within 30 seconds of the others.

go off when you’re touching of selected pads To relight, touch any pad again, or unlock and relatch door.

setting controls

Water standing in This is normal • A small amount of clean water around the outlet on the tub

the bottom of the tub bottom at the back of the tub keeps the water seal lubricated.

Water won’t pump Drain is clogged • If you have an air gap, clean it. See page 12.

out of the tub •If the dishwasher drains into a disposer, run disposer clear.

•Check to see if your kitchen sink is draining well. If not, you

may need a plumber.

Steam This is normal • Warm, moist air comes through the vent by the door latch during drying

and when water is being pumped out. This is necessary for drying.

Sanitized light does The door was opened and the • Do not interrupt the cycle anytime during or after main wash.

not illuminate at the cycle was interrupted during

end of the cycle or after the main wash portion

(Anti-Bacteria The incoming water • Raise the water heater temperature to between 120°F and 140°F.

cycle only) temperature was too low

Noise Normal operating sounds • Detergent cup opening.

•Water entering dishwasher.

•The motor stops and starts at various times during the cycle.

•Drain pump sounds during the pump out.

Rattling dishes when the spray • Make sure dishes are properly loaded. See the Loading the

arm rotates dishwasher racks section.

Warrantor: General Electric Company. Louisville, KY 40225

What GE Will Not Cover:

For The Period Of: GE Will Replace:

One Year Any part of the dishwasher which fails due to a defect in materials or workmanship. During this

From the date of the limited one-year warranty, GE will also provide, free of charge, all labor and related service to

original purchase replace the defective part.

15

GE Dishwasher Warranty.

■Service trips to your home to teach you how to use

the product.

■Improper installation, delivery or maintenance.

■Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

■Replacement of house fuses or resetting of circuit

breakers.

■Damage to the product caused by accident, fire, floods

or acts of God.

■Incidental or consequential damage caused by possible

defects with this appliance.

■Cleaning or servicing of the air gap device in the

drain line.

■Damage caused after delivery.

■Product not accessible to provide required service.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for

home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not

available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE

Service location for service. Proof of original purchase date is needed to obtain service under the warranty. In

Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know

what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care®technician. To schedule

service, on-line, 24 hours a day, visit us at ge.com, or call

800.GE.CARES (800.432.2737). Please have serial number

and model number available when calling for service.

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular

purpose, are limited to one year or the shortest period allowed by law.

Consumer Support.

GE Appliances Website ge.com

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,

any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,

order parts or even schedule service on-line.

Schedule Service ge.com

Expert GE repair service is only one step away from your door. Get on-line and schedule your service at

your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.

Real Life Design Studio ge.com

GE supports the Universal Design concept—products, services and environments that can be used by

people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and

mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design ideas

for people with disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC

(800.833.4322).

Extended Warranties ge.com

Purchase a GE extended warranty and learn about special discounts that are available while your warranty

is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.

GE Consumer Home Services will still be there after your warranty expires.

Parts and Accessories ge.com

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at

800.626.2002 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

Contact Us ge.com

If you are not satisfied with the service you receive from GE, contact us on our Website with all the details

including your phone number, or write to: General Manager, Customer Relations

GE Appliances, Appliance Park

Louisville, KY 40225

Register Your Appliance ge.com

Register your new appliance on-line—at your convenience! Timely product registration will allow for

enhanced communication and prompt service under the terms of your warranty, should the need arise.

You may also mail in the pre-printed registration card included in the packing material, or detach and

use the form in this Owner’s Manual.

Printed in the United States

Printed on Recycled Paper