Ge Appliances General Electric Washer Dryer Wbsr3140 Users Manual 49 90212

WHDRR418 to the manual b04c5036-e62b-43c4-a2f4-53de41a555bd

2015-01-23

: Ge-Appliances Ge-Appliances-General-Electric-Washer-Dryer-Wbsr3140-Users-Manual-258456 ge-appliances-general-electric-washer-dryer-wbsr3140-users-manual-258456 ge-appliances pdf

Open the PDF directly: View PDF PDF.
Page Count: 16

www.GEAppliances.com
WBSR3140
WCSR4170
WJSR4160
WHDRR418
WHDSR315
WHDSR417
WJRR4170
Owner’s Manual
Washers
175D1807P482 49-90212 08-04 JR
Safety Information . . . . . . . 2, 3
Operating Instructions
Control Panels
and Settings . . . . . . . . . . . . . 4–7
Features . . . . . . . . . . . . . . . . .7, 8
Loading and Using
the Washer . . . . . . . . . . . . . .9, 10
Troubleshooting Tips
Before You Call
For Service . . . . . . . . . . . . 11–14
Consumer Support
Consumer Support . . Back Cover
Warranty . . . . . . . . . . . . . . . . . 15
Write the model and serial
numbers here:
Model # __________________
Serial # __________________
You can find them in the upper
right corner on the back of your
washer.
2
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
WATER HEATER SAFETY
Under certain conditions hydrogen gas may be produced in a water heater that has not been used for
two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by
turning on all hot water faucets and allowing them to run for several minutes. Do this before using any
electrical appliance which is connected to the hot water system. This simple procedure will allow any
built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or
appliance during this process.
PROPER INSTALLATION
■Keep the area underneath and around your
appliances free of combustible materials such
as lint, paper, rags, chemicals, etc.
■Close supervision is necessary if this appliance is
used by or near children. Do not allow children
to play on, with or inside this or any other
appliance.
YOUR LAUNDRY AREA
This washer must be properly installed and located in accordance with the Installation Instructions
before it is used. If you did not receive an Installation Instructions sheet, you can receive one by visiting
www.GEAppliances.com, or by calling 800.GE.CARES (800.432.2737).
■Install or store where it will not be exposed
to temperatures below freezing or exposed to
the weather, which could cause permanent
damage and invalidate the warranty.
■Properly ground washer to conform with all
governing codes and ordinances. Follow details
in Installation Instructions.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
3
Use this
appliance
only for its
intended
purpose as
described in
this Owner’s
Manual.
www.GEAppliances.com
SAVE THESE INSTRUCTIONS
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
■Turn off water faucets to relieve pressure on
hoses and valves and to minimize leakage if
a break or rupture should occur. Check the
condition of the fill hoses; they should be
replaced every 5 years.
■Before discarding a washer, or removing it
from service, remove the washer lid to prevent
children from hiding inside.
■Do not attempt to repair or replace any part of
this appliance unless specifically recommended
in this Owner’s Manual, or in published user-
repair instructions that you understand and
have the skills to carry out.
■Do not tamper with controls.
WHEN NOT IN USE
■Never reach into washer while it is moving.
Wait until the machine has completely stopped
before opening the lid.
■Do not mix chlorine bleach with ammonia or
acids such as vinegar and/or rust remover.
Mixing different chemicals can produce a toxic
gas which may cause death.
■Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.). These substances give
off vapors that may ignite or explode. Do not
add these substances to the wash water. Do not
use or place these substances around your
washer or dryer during operation.
■
The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
wash and care instructions.
■To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
NOTE: Turning the Cycle Selector knob to an
off position does NOT disconnect the appliance
from the power supply.
■Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a
damaged cord or plug.
WHEN USING THE WASHER
4
Model WBSR3140
Model WCSR4170
• Add detergent
• Add diluted fabric
softener (on models
with a fabric
softener dispenser)
• Add clothes
• Select load size and
other wash options
• Select wash cycle • Close lid
• Pull knob
You can locate your model number on the back of your washer.
About the washer control panel.
Quick Start Guide
www.GEAppliances.com
Model WJSR4160
Model WHDSR315
Model WHDSR417
Model WHDRR418
5
6
Control settings.
Load Size
Loosely load clothes no higher than the top row of holes in the washer basket. The water level should just cover the
clothes. Adjust the load size accordingly.
Temperature
Select the water temperature for the wash and rinse cycles. Always follow fabric manufacturer’s care label or
instructions when laundering.
Wash Cycle
The wash cycle controls the length of the washing process. The chart below will help you match the wash cycle setting
with your clothing.
COTTONS For heavy to lightly soiled cottons, household linens, work and play clothes.
EASY CARE For wrinkle-free and permanent press items, and knits.
DELICATES For lingerie and special-care fabrics with light to normal soil.
POWER WASH For heavily soiled and heavy-duty fabrics. This cycle provides a longer agitation.
POWER RINSE Provides an automatic, second deep rinse to thoroughly remove detergent or bleach from your clothes.
15 MIN/30 MIN For very soiled clothes. Begins with a brief agitation, soaks for a specified period of time, then moves through the rest
AUTO SOAK of the cycle automatically.
PREWASH Use to wash heavily soiled clothes twice with detergent in each cycle. Automatically advances into
the COTTONS wash cycle.
To deliver extra detergent:
Liquid Detergent–Place in fabric softener dispenser for use in second wash. DO NOT use dispenser for fabric softener.
Powder Detergent–Place extra detergent in tub for use in first wash (approximately 11⁄2times normal
amount recommended).
About the washer control panel.
Model WJRR4170
7
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
The Agitator Cap or Fabric Softener Dispenser (depending on model)
The agitator cap fits into the top of the
agitator. If it accidentally comes off, simply
put it back on.
The fabric softener dispenser automatically
releases liquid fabric softener at the
proper time during the cycle.
Do not stop the washer during the first spin.
This will cause the dispenser to empty too soon.
To use, follow these steps:
Make sure dispenser is securely
attached to agitator.
Use only liquid fabric softener.
Pour into dispenser, using amount
recommended on package.
Never pour fabric softener directly on clothes.
It may stain them.
Add water to dispenser until it reaches
the maximum fill line.
3
2
1
Do not pour anything into the agitator if the
agitator cap or dispenser is removed.
About the washer features.
NOTE: Not all features are available on all washer models. www.GEAppliances.com
2nd Rinse Option (on some models)
When you use extra detergent or bleach
to clean heavily soiled clothes, you may
want to use the 2nd Rinse option. It
provides a second deep cold rinse. On
some models, this option can be found on
the cycle selector knob.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
8
Cleaning the Fabric Softener Dispenser (on some models)
Remove the dispenser from the top of the agitator.
Separate the dispenser cup from the cover by grasping the top and pushing down
on the inside of the cup with your fingers. Dispenser cup will pop free from the
cover.
To clean the dispenser, soak both the dispenser cup and the dispenser cover in the
following solution:
■1 US gallon (3.8 liters) warm water
■ 1/4 cup (60 ml) heavy duty liquid detergent
■1 cup (240 ml) bleach
If necessary, loosen buildup with a clean, soft cloth after soaking. Do not use a stiff
brush; you may roughen the surface of the dispenser.
Rinse and reassemble dispenser. Place dispenser back on the agitator.
5
4
3
2
1
Separate for cleaning.
Liquid Bleach Dispenser (on some models)
The dispenser dilutes liquid chlorine bleach before it reaches your wash load.
Check clothing care labels for special instructions.
Measure liquid bleach carefully, following instructions on the bottle.
■ Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket.
■ Do not pour powdered bleach into bleach dispenser.
Before starting the washer, pour measured amount of bleach directly into bleach
dispenser. Avoid splashing or over-filling dispenser. If you prefer to use powdered
bleach, add it into the wash basket with your detergent.
■ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing can produce a toxic gas which may cause death.
3
2
1
About the washer features.
NOTE: Not all features are available on all washer models.
9
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Sorting Wash Loads
Proper Use of Detergent
Add detergent and start the washer before adding
clothes so that the detergent can work effectively.
Using too little or too much detergent is a common
cause of laundry problems.
You can use less detergent if you have soft water,
a smaller load or a lightly soiled load.
Loading the Washer
Load dry items loosely, no higher than the top
row of holes in the washer basket. When loading
wet items make sure you set the load/water level
high enough to allow the items to move freely.
Water level should just cover the clothes. To add
items after washer has started, push in Cycle
knob and submerge additional items next to the
agitator. Close the lid and pull Cycle knob out
to restart.
■Do not wrap long items like sheets or pants
around the agitator.
■Do not wash fabrics containing flammable
materials (waxes, cleaning fluids, etc.).
■Agitation will not start with the lid up.
Sort by color (whites, lights, colors), soil level,
fabric type (sturdy cottons, easy care, delicates)
and whether the fabric produces lint (terry cloth,
chenille) or collects lint (velveteen, corduroy).
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering. www.GEAppliances.com
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
10
Care and Cleaning of the Washer
Wash Basket: Leave the lid open after washing to
allow moisture to evaporate. If you want to clean the
basket, use a clean soft cloth dampened with liquid
detergent, then rinse. (Do not use harsh or gritty
cleaners.)
Fill Hoses: Hoses connecting washer to faucet
should be replaced every 5 years.
Exterior: Immediately wipe off any spills. Wipe with
damp cloth. Try not to hit surface with sharp objects.
Moving and Storage: Ask the service technician to
remove water from drain pump and hoses. See the
Installation Instructions packed with product for
information on how to reinstall the shipping rod to
keep the tub stationary when moving the washer.
For more information, visit www.GEAppliances.com,
or call 800.GE.CARES (800.432.2737). Do not store
the washer where it will be exposed to the weather.
Long Vacations: Be sure water supply is shut off at
faucets. Drain all water from hoses if weather will
be below freezing.
Fabric Care Labels
Machine
wash
cycle Normal Permanent Press/
wrinkle resistant
Gentle/
delicate Hand wash Do not wash Do not wring
Water
temperature Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
Tumble
dry
Dry Normal Permanent Press/
wrinkle resistant
Gentle/
delicate Do not tumble dry
Do not dry
(used with
do not wash)
Heat
setting
High Medium Low No heat/air
Bleach
symbols Any bleach
(when needed) Only non-chlorine bleach
(when needed)
Do not bleach
WASH LABELS
DRY LABELS
BLEACH LABELS
Below are fabric care label “symbols” that affect the clothing you will be laundering.
Loading and using the washer. Always follow fabric manufacturer’s care label when laundering.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
WATER Possible Causes What To Do
Too many suds Type of detergent •Switch to a lower sudsing detergent brand and follow
instructions on package.
Soft water •Try less detergent.
Too much detergent •Measure your detergent carefully. Use less soap if you
have soft water, a smaller load or a lightly soiled load.
Water leaks Fill hoses or drain hose is •Make sure hose connections are tight at faucets and
improperly connected rubber washers are installed. Make sure end of drain
hose is correctly inserted in and secured to drain facility.
The drain hose should be inserted into the washer and
the collar or clip should be screwed in. Remove any kinks
from the drain hose. Make sure that the hose connection
is not strained when the washer is pushed close to the
wall.
Household drain may be clogged •Check household plumbing. You may need to call a
plumber.
Constant water pressure to the fill •Tighten hoses at the faucets and turn the water off after
hoses at the water source each use.
•Check condition of the fill hoses; they should be replaced
every 5 years.
Using too much detergent in •Use less detergent. Use less soap if you have soft water, a
washer smaller load or a lightly soiled load.
Fill hoses, washers and screens •Check that the rubber washers and screens have been
installed correctly. Fill hoses, washers and screens should
be replaced every 5 years.
Overloading the washer •Loosely load clothes no higher than the top row of holes
in the washer basket. The level of the water should be just
above the clothes.
Water temperature
Cooler water temperatures provide
•New laundry detergents have been formulated to
eems incorrect improved energy efficiency work with cooler water temperatures without affecting
wash performance.
Control is not set properly •Check water temperature control (on some models) or
Cycle knob and adjust.
Water supply is turned off •Turn both hot and cold faucets fully on and make sure
or improperly connected hoses are connected to correct faucets.
Water valve screens are •Turn off the water source and remove the water
stopped up connection hoses from the upper back of the washer. Use
a brush or toothpick to clean the screens in the machine.
Reconnect the hoses and turn the water back on.
House water heater is •Make sure house water heater is delivering water
not set properly at 120°F–140°F (48°C–60°C).
Water won’t drain Drain hose is kinked or •Straighten drain hose and make sure washer is not sitting
improperly connected on it.
•Top of drain outlet should be less than 8 ft. (2.5 m)
above floor.
11
Troubleshooting Tips
Save time and money! Review the charts on the following
pages, or visit www.GEAppliances.com. You may not need
to call for service.
Before you call for service… www.GEAppliances.com
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
PERFORMANCE Possible Causes What To Do
Colored spots Incorrect use of fabric •Check fabric softener package for instructions and follow
softener directions for using dispenser.
•Pretreat stain and rewash.
Dye transfer •Sort whites or lightly colored items from dark colors.
OPERATION Possible Causes What To Do
Washer pauses during This is normal •The washer may pause during the spin cycle to remove
spin cycle soapy water more efficiently.
Washer won’t operate Washer is unplugged •Make sure cord is plugged securely into a working outlet.
Water supply is turned off •Turn both hot and cold faucets fully on.
Controls are not set •Check controls and make sure Cycle knob is pulled out
properly to ON position.
Lid is open—safety feature •Close lid and reset cycle, to the beginning if necessary.
prevents agitation and spinning
when lid is up
Circuit breaker/fuse is •Check house circuit breakers/fuses. Replace fuses or
tripped/blown reset breaker. Washer should have separate outlet.
Before you call for service…
12
WATER Possible Causes What To Do
Water fills and drains Siphoning •If your standpipe or drain for the washer is less than 3
at the same time feet off the floor, the water will drain from the tub while
it is filling. Lifting the drain hose at least 3 feet off the
floor will allow the water to remain in the tub until the
pump drains it out. The anti-siphon clip will lift the drain
hose high enough to do this. The anti-siphon clip is
included with the installation parts package for your
washer.
•Another way siphoning can occur is if the standpipe is
stuffed with rags or other items that prevent air from
escaping with the water. Air flow is needed to break the
suction.
•Check to make sure only the straight part of the drain
hose is inserted into the standpipe; no ribs of the drain
hose should be in the standpipe or drain pipe.
•The washer drain must be 3 feet or more off of the floor
to prevent the washer from draining during fill. If your
washer drain is less than 3 feet above the floor, use the
anti-siphon clip shipped with your washer to attach the
drain hose to the back of your washer. The clip will hold
the drain hose in place and ensure that the washer does
not self-drain during fill. See installation instructions for
details.
•Only the straight top portion of the drain hose should be
inserted into the drain. Inserting the ribbed section of
the hose may create a siphon, and cause the washer to
drain as it fills.
•If the drain opening is excessively tight around the drain
hose, or if the opening around the hose is closed with
rags or other material, a siphon may occur, and the
washer will drain as it fills. To avoid this problem, ensure
that there is open area around the end of the drain hose
to allow air to flow into the drain as water is pumped out
of the washer.
PERFORMANCE (cont.) Possible Causes What To Do
Grayed or yellowed Not enough detergent •Use more detergent (especially with larger loads). Be
clothes sure to follow detergent manufacturer’s directions.
Hard water •Use a water conditioner like Calgon brand or install
a water softener.
Water is not hot enough •Make sure water heater is delivering water at
120°F–140°F (48°C–60°C).
Washer is overloaded •Select load size to match clothes load.
Detergent is not •Add detergent as wash basket fills with water before
dissolving you load clothes.
Dye transfer •Sort clothes by color. If fabric label states wash separately,
unstable dyes may be indicated.
Lint or residue on Clothes are air or line dried •If you do not dry your clothes with a clothes dryer, your
clothes clothes may retain more lint.
Incorrect sorting •Separate lint producers from lint collectors.
Washing too long •Wash small loads for a shorter time than larger loads.
Detergent not dissolving •Add detergent as wash basket fills with water, before you
load clothes.
•Try a liquid detergent.
•Use warmer water temperature.
Overloading •Load clothes no higher than the top row of holes in the
washer basket.
•Make sure load size selected matches clothes load size.
Incorrect use of fabric softener •Check fabric softener package for instructions and follow
directions for using dispenser.
Pilling Result of normal wear on •While this is not caused by the washer, you can slow the
poly-cotton blends and pilling process by washing garments inside out.
fuzzy fabrics
Snags, holes, tears, rips Pins, snaps, hooks, sharp •Fasten snaps, hooks, buttons and zippers.
or excessive wear buttons, belt buckles, •Remove loose items like pins, objects in pockets
zippers and sharp objects and sharp buttons.
left in pockets •Turn knits (which snag easily) inside out.
Undiluted chlorine bleach •Check bleach package instructions for proper amount.
•Never add undiluted bleach to wash or allow clothes
to come in contact with undiluted bleach.
Chemicals like hair bleach •Rinse items that may have chemicals on them before
or dye, permanent wave washing.
solution
Wrinkling Improper sorting •Avoid mixing heavy items (like work clothes) with
light items (like blouses).
•Try a fabric softener.
Overloading or •Load your washer so clothes have enough room
incorrect water level to move freely with water covering all of the clothes.
Incorrect wash and •Match Cycle selection to the type of fabric you are
dry cycles washing (especially for easy care loads).
Repeated washing in •Wash in warm or cold water.
water that is too hot
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
www.GEAppliances.com
13
14
Before you call for service…
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
OTHER Possible Causes What To Do
Labels on the exterior Occasionally the adhesive •Use a hair dryer set at the lowest heat setting, directing
of the washer will not used on the labels does the air at the label for a short amount of time. This will
peel off cleanly not release cleanly release the adhesive easily, without damaging the surface
of the washer.
NOISE Possible Causes What To Do
Washer is noisy Washer is uneven •To level the front of the washer, adjust the front leveling
legs by rotating the individual leg in the proper direction
for up or down. To level back of washer, lift back of
machine 4″(11 cm) and set down.
Washer load is •Push the Cycle knob in to stop the washer, open the lid
unbalanced and redistribute the load evenly. Close the lid and restart.
Shipping rod is still assembled •To remove shipping rod from washer, pull yellow tag and
in unit attached rod from the bottom right hand side of washer.
Washer is sitting too close •Pull washer away from the wall; about 4″(11 cm) is
to wall (causes knocking needed.
during cycle)
Whistle or knock during fill •Normal sounds during fill include the water filling
in through the house plumbing. As the water pressure
goes up and down, a knock or hammer can develop.
Make sure the water faucets are fully turned on.
Clanking or clunking •Many washers have features such as pulse agitation and
pauses during rinse and spin for reduced clothes wear
and to reduce likelihood of soap residue. These short
pauses of less than 1 minute are normal and will reduce
clothing wear and increase water extraction. Sounds such
as a metallic knock, double knock or metallic clunk
occur when the washer transitions from a stop or paused
state to running or spinning. They occur several times
per cycle after speed changes or pauses.
•Normal sounds during fill include the sound of water
flowing through your hosehold pipes. Additionally, a
knock, or hammering sound may also occur when the
washer water valves turn off. To reduce this noise, make
sure that the washer fill faucets are fully opened.
•Your washer will pause between the various wash, rinse,
spin and drain portions of the wash cycle. It may also
pause during agitation if a Pulsed Agitation cycle is
selected. Sounds such as metallic knocks or clinking may
occur during these transitions from running to stopped
or from stopped to running. They may also occur if your
machine changes speeds or brakes during a wash cycle.
For The Period Of: We Will Replace:
One Year Any part of the washer which fails due to a defect in materials or workmanship. During this
From the date of the full one-year warranty, we will also provide, free of charge, all labor and related service to replace
original purchase the defective part.
Second through The transmission, suspension rod and spring assembly if any of these parts should fail due to a defect
Fifth Year in materials or workmanship. GE will also replace the washer lid or cover, if they should rust
From the date of the under operating conditions. During this additional four-year limited warranty, you will be
original purchase responsible for any labor or related service costs.
Second through The washer tub, if it should fail due to a defect in materials or workmanship. During this
Tenth Year additional nine-year limited warranty, you will be responsible for any labor or related service costs.
From the date of the
original purchase
Second through The washer basket, if it should fail due to a defect in materials or workmanship. During this
Twentieth Year additional nineteen-year limited warranty, you will be responsible for any labor or related
From the date of the service costs.
original purchase
What Is Not Covered:
15
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
All warranty service provided by our Factory Service Centers,
or an authorized Customer Care®technician. To schedule service,
on-line, 24 hours a day, visit us at www.GEAppliances.com,
or call 800.GE.CARES (800.432.2737).
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the
warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or
your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
■Service trips to your home to teach you how to use
the product.
■Improper installation, delivery or maintenance.
■Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
■Replacement of house fuses or resetting of circuit
breakers.
■Products which are not defective or broken, or which are
working as described in the Owner’s Manual.
■Damage to the product caused by accident, fire, floods or
acts of God.
■Incidental or consequential damage caused by possible
defects with this appliance.
■Defects or damage due to operation in freezing
temperatures.
■Damage caused after delivery.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
GE Washer Warranty.
Printed in the United States
GE Appliances Website www.GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service www.GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio www.GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties www.GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories www.GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us www.GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance www.GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Consumer Support.

Navigation menu