Ge Rotary Control Valves Masoneilan 39003 Series Technical Specifications

Ge-Rotary-Control-Valves-Masoneilan-39003-Series-Technical-Specifications-656455 ge-rotary-control-valves-masoneilan-39003-series-technical-specifications-656455

2015-03-11

: Ge Ge-Rotary-Control-Valves-Masoneilan-39003-Series-Technical-Specifications-656455 ge-rotary-control-valves-masoneilan-39003-series-technical-specifications-656455 ge pdf

Open the PDF directly: View PDF PDF.
Page Count: 24

Technical Specifications
07/2014
GE Oil & Gas
39003 Series
Masoneilan* High Performance Butterfly Valves
(HPBV)
2 | GE Oil & Gas
39003 Series High Performance Butterfly Valves (HPBV) | 3
Table of Contents
GE’s Masoneilan 39003 Series High Performance Butterfly Valve
(HPBV) is a heavy duty automatic throttling control valve that
incorporates the two basic features of the HPBV types. These
features differentiate the the Masoneilan* 39003 Series HPBV
from the conventional swing-through butterfly valve in regards to
sealing method and operational characteristics. Specifically, the
two basic features are: (1) A PTFE, RTFE, or metal seal ring instead
of a liner, and (2) The employment of double offset (eccentric
operation). Each of these features contributes to the improved
performance of HPBV’s compared to conventional butterfly valves.
The use of a seal ring (PTFE, RTFE, or metal) eliminates the inherent
problems of high sealing forces, due to interference fit, and the
resultant high wear rates due to scraping and scuffing of liners.
Also, due to the design of the seal itself, which is a dynamic pres-
sure-assisted member, ANSI Class VI shutoff rates are available
throughout the full range of ANSI Class 150, 300 and 600 ratings
(soft-sealed constructions only).
The double offset (eccentric) operating principles of both seal off-
set (the seal ring centerline is offset from the shaft centerline – see
Figure 1) and shaft offset (the shaft centerline is offset from the
valve centerline – see Figure 1) allows the disc to get off the seal
quickly due to the camming rotation with respect to the valve/seal
centerlines. This results in minimal sliding (friction producing) con-
tact between the disc and the seal ring with complete separation
after only a few degrees of rotation.
The overall characteristics of the Masoneilan* 39003 Series Valve
are listed below:
• Long seal life – Offset (eccentric) operation gets the disc off the
seal quickly, minimizing sliding contact and friction, resulting
in reduced seal wear and lower breakaway and seating torque
requirements.
• Fast/dynamic operation – Offset (eccentric) operation elim-
inates disc-to-seal friction throughout the operating range
resulting in fast response to input signals. Also, the disc tends to
move in the direction of flow, assisting the valve and actuator to
maximize the allowable operating pressures.
• Excellent flow characteristics – the offset (eccentric) disc design
provides an approximate equal percentage flow characteristic
through its full travel of 90° rotation yielding a Cv ratio of 100:1.
• Extra heavy shafts with keyed ends for actuator mounting –
precise and accurate positioning without lost motion or back-
lash.
PTFE-lined low-friction bearing – Reduces operating torque and
promotes fast response to valve and actuator action. The triple
bearing support of the shaft prevents deflection of the shaft due
to side-loading.
Field replaceable components – Unlike most competitive valves,
shaft and disc need not be purchased as a set. The Masoneilan*
39003 Series Valve uses tapered pins to attach the shaft and disc
positively, yet provide component interchangeability.
Trade names noted throughout are for reference only. GE reserves
the right to supply trade named material or its equivalent.
Foreward
Foreword ....................................................................................................................3
Features .....................................................................................................................4
Numbering System ...............................................................................................5
General Data ............................................................................................................7
Pressure/Temperature Ratings ........................................................................ 8
Body Assembly Data ......................................................................................... 10
Actuator Data ....................................................................................................... 11
Rated Flow Coefficients (CV) and Pressure Recovery Coefficients (FL) ....... 12
Standard Valve Components ......................................................................... 14
Allowable Pressure Drops ................................................................................ 16
Weights ................................................................................................................... 17
Dimensions ............................................................................................................ 19
GE Sales Offices ................................................................................. Back Cover
4 | GE Oil & Gas
Features
GE’s Masoneilan 39003 Series HPBV includes unique valve seal designs for
metal, soft seal, and fire-safe configurations.
Metal Seal Design
The metal seal design incorporates an Inconel seal for higher tensile strength,
a 300 series stainless steel back-up ring in the seal cavity for axial seal
support, and a disc that is case hardened by nitriding.
The Inconel seal, by its dynamic and flexible design, applies enough force per
linear inch against the disc edge (Rockwell Hardness of C66 to C70) to obtain
an optimum sealing characteristic while controlling the loads between the
metal surfaces.
The metal seal design can be utilized for temperatures up to 900˚F, in
compliance with ANSI B16.34 pressure/temperature specifications. Leakage
is rated at Class IV per ANSI FCI 70-2.
Soft Seal Design
The soft seal design provides a bi-directional bubble tight shutoff (zero
leakage) through the use of a patented seal. This unique seal design creates a
self-energized seal in vacuum-to-low pressure applications.
Under higher pressure conditions, the seal is also designed to confine and
direct movement of the soft seal against the disc edge, up to the full ANSI
Class 150, 300 and 600 Cold Working Pressures.
The soft seal is designed for high services with minimal wear and low torque.
Seal replacement is a simple procedure requiring no special tools.
Fire-Safe Seal Design
The fire-safe seal design incorporates two patented seals which function
together to seal off pipeline flow. In normal operation, the soft seal provides a
bi-directional “bubble tight” shutoff (zero leakage); the metal seal provides bi-
directional shutoff in the event of a fire, in conformance to industry fire-safe
requirements.
With little or no pressure, the fire-safe seal creates a self-energized seal
against the disc. Higher line pressures act on the geometry of both seals
to dynamically load them against the disc, creating higher sealing forces in
either direction.
The metal seal is made of Inconel material which is shaped by a proprietary
hydroforming process into its unique, patented design. Stainless steel outer
bearings are included for post-fire disc and shaft alignment. Fireproof
packing is used to prevent external shaft leakage.
Disc/Nitrided
300 Series Stainless
Steel Backup Ring
Inconel Seal
Disc
Seal
“O” Ring
Disc
Metal Seal
Soft Seal
“O” Ring
Metal Seal Gasket
39003 Series High Performance Butterfly Valves (HPBV) | 5
Numbering System
—
1st 2nd 1st 2nd 3rd 4th 5th
3 3 3 9 3
Actuator Type
33 Spring Diaphragm
(Air to extend action
only with or without
auxilliary handwheel)
Body
Series
39
Actuator Mounting
(Type 25 Only)
0. Undefined
1. Horizontal above center. Valve
opens on stem extension (air-
to-open action)
2. Horizontal above center. Valve
closes on stem extension (air-
to-close action)
*3. Vertical above center. Valve
opens on stem extension (air-
to-open action)
*4. Vertical above center. Valve
closes on stem extension (air-
to-close action)
5. Horizontal below center. Valve
opens on stem extension (air-
to-open action)
6. Horizontal below center. Valve
closes on stem extension (air-
to-close action)
7. Vertical above center. Valve
opens on stem extension (air-
to-open action)
8. Vertical above center. Valve
closes on stem extension (air-
to-close action)
Seat
Material
1. PTFE or
RTFE Seal
Ring
2. Inconel
Seal Ring
3. Fire-Safe
Seal Ring
Not Assigned
3
—
*Standard Actuator Mounting Arrangement
Note 1: Looking at valve from actuator and
bracket end, valve would not be visible.
Note 2: Positions 1, 2, 5 and 6 shown dotted
and obtained by rotating the valve 180° about
its shaft axis.
Caution: The valve must not be installed
with the actuator mounted vertically below
center.
Figure 2
6 | GE Oil & Gas
Numbering System
—
1st 2nd 1st 2nd 3rd 4th 5th
3 4 3 9 3
Actuator Type
34 Double acting or
spring return piston
actuator
Body
Series
39
Actuator Mounting
(Type 25 Only)
0. Undefined
*1. Parallel to pipe. Air to open
action.
*2. Parallel to pipe. Air to close
action.
3. Perpendicular to pipe. Air to
open action.
4. Perpendicular to pipe. Air to
close action.
5. Parallel to pipe. Air to open
action.
6. Parallel to pipe. Air to close
action.
7. Perpendicular to pipe. Air to
open action.
8. Perpendicular to pipe. Air to
close action.
Seat
Material
1. PTFE or
RTFE Seal
Ring
2. Inconel
Seal Ring
3. Fire-Safe
Seal Ring
Not Assigned
3
—
*Standard Actuator Mounting Arrangement
Figure 3
39003 Series High Performance Butterfly Valves (HPBV) | 7
General Data
Flow Characteristic: equal percentage
Flow Direction: bi-directional
Seal Leakage: per ANSI FCI 70-2 Class VI,
PTFE, RTFE
Class IV, metal seals
Cv Ratio: 100:1
Valve Sizes ANSI Class
inches mm 150 Carbon
& St. St.
300 Carbon
& St. St.
600(1)
Carbon &
St. St.
2 50 •••
3 80 •••
4 100 •••
6 150 •••
8 200 •••
10 250 •••
12 300 •••
14 350 •••
16 400 •••
18 450 • •
20 500 • •
24 600 • •
30 750 • •
36 900 •
42 1050 •
48 1200 •
1. ANSI Class 600 rating available in soft seat constructions only. Consult
GE for fire-safe or metal seat requirements.
8 | GE Oil & Gas
Pressure/Temperature Ratings
Soft and Fire-Safe Seal
As temperature increases, the pressure retaining capability of
materials decreases. The graph below illustrates the pressure/
temperature ratings for ANSI Class 150, Class 300 and Class 600.
The heavy lines define the ratings of the carbon steel and stainless
steel valve body (or “shell”) in conformance to ANSI B16.34. The
shaded areas define the ratings of the PTFE and RTFE Seal materi-
als (Soft Seal).
Seal ratings are based on differential pressure with the disc in the
fully closed position.*
Steam Service (Soft Seal only)
PTFE sealed valves are rated for 50 psi saturated steam.
Valves with “O” seal configuration (RTFE seal/AFLAS O-ring) are
rated to 100 psi steam service.
ANSI B16.34 Body and Flowseal Soft Seat Pressure - Temperature Ratings
* Valves with 316SS shafts are rated for maximum pressure differentials of 150 psi for Class 150, 300 psi for Class 300, and 600 psi for
Class 600.
39003 Series High Performance Butterfly Valves (HPBV) | 9
Pressure/Temperature Ratings
Metal Seal
As temperature increases, the pressure retaining capability of
materials decreases. The graph below illustrates the pressure/
temperature ratings for ANSI Class 150, Class 300 and Class 600.
The heavy lines define the ratings of the carbon steel and stainless
steel valve body (or “shell”) in conformance to ANSI B16.34. The
shaded areas define the ratings of the metal seal.
Seal ratings are based on differential pressure with the disc in the
fully closed position.*
ANSI B16.34 Body and Flowseal Metal Seat Pressure - Temperature Rating
* Valves with 316SS shafts are rated for maximum pressure differentials of 150 psi for Class 150, 300 psi for Class 300, and 600 psi for
Class 600.
10 | GE Oil & Gas
Body Assembly Data
Body
Type:
wafer or lug with integral bonnet
Sizes:
2”, 3”, 4”, 6”, 8”, 10”, 12”, 14”, 16”, 18”, 20”, 24”, 30”, 36”, 42”,
48” (50 mm-1200 mm)
Materials:
carbon steel
ASTM A216 Gr WCB or ASTM A105
stainless steel
ASTM A351 Gr CF8M or ASTM A182-F316
Connections:
flangeless
clamped between ANSI Class 150, 300 or 600 line flanges
single flanged
bolts between ANSI Class 150, 300 or 600 line flanges
Ratings:
ANSI Class 150
carbon steel and stainless steel 2” - 48” sizes (50 mm-
1200 mm)
ANSI Class 300
carbon steel and stainless steel 2” - 30” sizes (50 mm-
750 mm)
ANSI Class 600
carbon steel and stainless steel 2” - 16” sizes (50 mm-
400 mm)
Seal:
PTFE, RTFE or Inconel with 304 stainless steel O-Ring
Disc
Type:
offset eccentric disc
Materials:
stainless steel ASTM A351 Gr CF8M or ASTM A182-F316
Nitrided
Shaft
Type:
Keyed on outboard end
Materials:
17-4 PH stainless steel A564 Gr 630 (others optional)
Valve Bearings:
PTFE-lined fiberglass
bronze (up to 750° F)
stainless steel (above 750° F)
Packing Box:
bolted
Packing
PTFE V-ring
graphite (optional)
39003 Series High Performance Butterfly Valves (HPBV) | 11
Actuator Data
(Model 33) – Sizes 3” – 8”
(80mm – 200mm)
Type:
spring-diaphragm, floating stem pneumatic actuator
Action:
increasing air extends stem
Bench Range:
B size 7-16 psig (48-110 kPa) size 9-16 psig (62-110 kPa)
Connection:
1/4” NPT
Fail Safe Action:
field reversible
Yoke:
carbon steel
Bracket:
cast iron
Handwheel:
(optional) push type tilting, rising stem, permanently
lubricated materials: 17-4 PH and AISI 416 stainless steel
adjustable limit stops
Bracket Bearing:
a sealed, permanently lubricated ball bearing
(Model 34) – Sizes 3” – 48”
(80mm – 1200mm)
Type:
Spring-return, or double-acting scotch yoke piston
Body:
Extruded aluminum, anodized finish sizes 210 to 280 &
88
Ductile Iron sizes 90 and 100
Seals:
Buna-N
Pressure rating:
150 psi (1034 kPa) maximum working pressure
Manual Override:
Declutchable direct mount sizes 210 to 280
Hydraulic size 88
Bevel Gear sizes 90 and 100
Optional Construction:
Low temperature or high temperature seals, low
pressure hydraulic.
Actuator
Size
Valve Size Effective Area Travel
in. mm. sq. in. sq. cm in. mm
B3 80 70 452 2.625 66.5
4 100 70 452 2.625 66.5
C
6 150 140 903 2.625 66.5
8 200 140 903 2.625 66.5
optional
3 80 140 903 2.625 66.5
4 100 140 903 2.625 66.5
12 | GE Oil & Gas
Rated Flow Coefficients (CV) and Pressure Recovery Coefficients (FL)
Rated Flow Coefficients (CV)
The values shown are for the valve installed in the seal upstream (“SUS”) position.
Valve Size ANSI Class
Degree Open/% Full CV
10° 20° 30° 40° 50° 60° 70° 80° 90°
1.5% 6% 14% 25.2% 38% 55% 75% 97% 100%
2
150 1.5 6 14 25 39 56 76 99 102
300 1.4 6 13 24 36 52 71 95 100
600 1.4 5 13 23 35 51 70 90 93
3
150 3.4 14 32 57 87 125 141 221 228
300 3.2 13 30 53 81 117 159 212 223
600 3.1 12 29 52 79 114 156 202 208
4
150 6.8 27 63 114 171 248 338 437 451
300 6.2 25 58 104 157 228 310 414 435
600 5.8 23 54 98 147 213 290 375 387
6
150 15.5 66 154 278 419 607 827 1070 1103
300 14.9 60 139 250 377 546 744 992 1041
600 14.7 59 137 247 372 538 734 950 979
8
150 30.9 124 289 520 784 1135 1584 2002 1064
300 27.3 109 255 459 692 1001 1365 1820 1911
600 26.8 107 250 451 679 983 1341 1734 1788
10
150 52.8 211 492 886 1336 1934 2638 3411 3817
300 45.6 183 26 767 1156 1673 2282 3042 3194
600 41.2 165 384 692 1044 1511 2060 2665 2747
12
150 72.6 290 677 1219 1838 2660 3628 4690 4837
300 63.3 253 590 1063 1602 2319 3163 4217 4428
600 58.4 233 545 981 1479 5140 2918 3774 3891
14
150 90 392 914 1646 2481 3592 4898 6530 6857
300 81 326 760 1368 2063 2986 4072 4530 5702
600 73 292 682 1228 1838 2680 3655 4727 4873
16
150 132 531 1230 2229 3361 4865 6634 8845 9287
300 109 435 1015 1827 2755 3988 5438 7850 8243
600 96 385 899 1619 2423 3533 4818 6231 6424
18 150 171 684 1596 3873 4332 6270 8550 11270 11400
300 139 555 1295 2331 3515 5088 6938 9250 9712
20 150 207 828 1932 3478 3244 7590 10350 13800 14420
300 158 630 1470 2646 3990 5775 7875 10150 10658
24 150 315 1260 2940 5292 7890 11550 15750 21000 22050
300 242 966 2254 4057 6118 8855 12075 16100 16205
30 150 491 1965 4585 8253 12445 18012 24563 32750 34388
300 404 1614 3769 6779 10222 14795 20175 26900 28245
36 150 707 2830 6602 1184 17920 25938 35370 45745 47160
42 150 963 3851 8987 16176 24392 35304 48143 62264 64190
48 150 1258 5030 11738 21128 31859 46111 62881 81324 83840
Pressure Recovery Coefficients (FL)
Disc Degree Opening
15o20o25o30o35o40o45o50o55o60o65o70o75o80o85o90o
Seal Upstream .95 .91 .84 .81 .78 .80 .77 .74 .74 .73 .70 .66 .63 .60 .57 .53
Seal Downstream .94 .89 .84 .82 .80 .77 .75 .72 .69 .66 .63 .30 .58 .55 .54 .53
39003 Series High Performance Butterfly Valves (HPBV) | 13
Standard Valve Components
End Seal Variation
The ANSI 150 14” through 24” sizes feature a two-piece shaft
design. The lower shaft utilizes an end seal in the body to prevent
external leakage. The component parts include an end seal, an
end cap and end cap bolts.
Lower Packing Variation
The ANSI 150 30” through 48”; ANSI 300 14” through 30”; ANSI
600 10” through 16” sizes feature a two-piece shaft design which
utilizes a lower packing seal in the valve body to prevent external
leakage. The component parts are of the same design used in the
packing assembly in the top of the valve body neck.
14 | GE Oil & Gas
Standard Materials of Construction
Metal Seal Design
Item
Number Description -20°F to +450°F
(-29°C to +232°C)
+451°F to +750°F
(+233°C to +399°C)
+751°F to +800°F
(+400°C to +427°C)
2 Shaft 17-4 PH Stainless Steel ASTM A564 Gr 630
5 Packing PTFE Graphite
6 Bearings Glass-Backed PTFE Bronze 316 Stainless Steel Nitrided
10 Body Carbon Steel A216 Gr WCB or A105
12 Disc 316 Stainless Steel A351 CF8M or A182 F316 Nitrided
14 Seal Inconel
Carbon Steel Construction
Item
Number Description -100°F to +450°F
(-73°C to +232°C)
+451°F to +750°F
(+233°C to +399°C)
+751°F to +900°F
(+400°C to +482°C)
2 Shaft 17-4 PH Stainless Steel ASTM A564 Gr 630 316 Stainless* Steel
ASTM A479 Gr 316
5 Packing PTFE Graphite
6 Bearings Glass-Backed PTFE Bronze 316 Stainless Steel Nitrided
10 Body 316 Stainless Steel A351 CF8M or A182 F316
12 Disc 316 Stainless Steel A351 CF8M or A182 F316 Nitride
14 Seal Inconel
* Metal seal valves with 316 SS shafts have reduced pressure differential ratings. Monel, Nitronic 50 and Inconel (718 or X750) may be
substituted for higher differential pressures and elevated temperatures. Please consult GE for application assistance.
Stainless Steel Construction
39003 Series High Performance Butterfly Valves (HPBV) | 15
Standard Materials of Construction
Item
Number Description -100°F to +400°F
(-73°C to +204°C)
+400°F to +500°F
(+204°C to +260°C)
2 Shaft 17-4 PH Stainless Steel ASTM A564 Gr 630
Optional: 316 SS, Inconel 718/750, Monel, Alloy 20, Nitronic 50, Hastelloy C, and Others
5 Packing TFE
Optional: Graphite
6 Bearings Glass-Backed PTFE
Optional: 316 SS Backed TFE, Hastelloy C Backed TFE
10 Body
Carbon Steel A216 Gr WCB or A105
Optional: 316 SS ASTM A351 CF8M or A182 F316, Monel,
Alloy 20, Aluminum Bronze, or Hastelloy C
12 Disc 316 Stainless Steel A351 CF8M or A182 F316
Optional: Monel, Alloy 20, Aluminum Bronze, or Hastelloy C
14 Seal PTFE
Optional: RTFE, Polyethylene (UHMWPE)
Soft Seal Design
Item
Number Description -100°F to +400°F
(-73°C to +204°C)
+400°F to +500°F
(+204°C to +260°C)
2 Shaft 17-4 PH Stainless Steel ASTM A564 Gr 630
Optional: 316 Stainless Steel
5 Packing Fire-Safe
6 Bearings Fire-Safe (Garfil & 316 SS)
10 Body Carbon Steel A216 Gr WCB or A105
Optional: 316 SS ASTM A351 CF8M or A182 F316, Monel, Alloy 20, or Hastelloy C, and Others
12 Disc 316 Stainless Steel A351 CF8M or A182 F316 - ENP
Consult Factory for Optional Materials
14 Seal Fire-Safe (TFE & Inconel) RTFE & Inconel
Optional: TFE & Monel, TFE & Hastelloy C RTFE & Monel, RTFE & Hastelloy C
Fire-Safe Design
16 | GE Oil & Gas
Allowable Pressure Drops
GE has created a simple actuator sizing and selection program,
which allows for quick and accurate actuator sizing based on
the specific service conditions. This program is designed to run
in Microsoft® Excel®, and is available from your local GE sales
representative.
The opening screen of the sizing program is shown below.
Operating variables can be selected from a number of pull-
down menus. The program will then provide an actuator
recommendation, along with calculations for the required torque
(with safety margins) for valve seating, unseating, and throttling
conditions.
This program covers standard product construction only. Please
consult with your local GE sales representative, or with the factory,
for applications and conditions not covered by this program.
39003 Series High Performance Butterfly Valves (HPBV) | 17
Weights (lbs.)
Actuator Type Valve
Wt
Brack-
et WT
RC210 RC220 RC230 RC240 RC250 RC260 RC270 RC280 RC88 RCI90 RCG100 33 Actuator
Valve
Size
Type DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR Yoke
Wt
DA DA
3.1 4 4 5.85 810.4 10.6 15.5 20.4 26.8 27 40 69 69 89 142 162 330 618 772 684 1102 32 85
2 WAFER 8 12 23.1 24 24 25.85 28 30.4 30.4 35.5 24 64 117
LUG 11 12 26.1 27 2 28.85 31 33.4 33.4 38.5 24 67 120
3 WAFER 11 12 26.1 27 27 28.85 31 33.4 33.4 38.5 24 67 120
LUG 13 12 28.1 29 29 30.85 33 35.4 35.6 40.5 24 69 122
4 WAFER 17 12 32.1 33 33 34.85 37 39.4 39.6 44.5 24 73 126
LUG 25 2 40.1 41 41 42.85 45 47.4 47.6 52.5 24 81 134
6 WAFER 30 12 50 52.4 52.6 57.5 62.4 68.8 69 82 24 139
LUG 35 12 55 57.4 57.6 62.5 67.4 73.8 74 87 24 144
8 WAFER 44 12 72.5 76.4 82.8 83 96 125 125 24 153
LUG 48 12 75.5 80.4 86.8 87 100 129 129 24 157
10 WAFER 71 14 105.4 111.8 112 125 154 154 174 227
LUG 191 14 125.4 131.8 132 145 174 174 194 247
12 WAFER 110 14 157 170 199 199 219 272
LUG 127 14 174 187 216 216 236 289
14 WAFER 135 16 182 195 224 224 244 297
LUG 183 16 230 243 272 272 292 345
16 WAFER 182 20 271 271 291 344 364 532
LUG 250 20 339 339 359 412 432 600
18 WAFER 234 20 323 323 343 396 416 584 872 1026 938
LUG 305 20 394 394 414 467 487 655 943 1097 1009
20 WAFER 320 20 429 482 502 670 958 1112 1024
LUG 414 20 523 576 596 764 1052 1206 1118
24 WAFER 505 25 692 860 1148 1302 1214 1632
LUG 702 25 889 1057 1345 1499 1411 1829
30 WAFER 925 25 1112 1280 1568 1722 1634 2052
LUG 1130 25 1317 1485 1773 1927 1839 2257
36 WAFER 1630 25 1985 2273 2427 2339 2757
LUG 1890 25 2245 2533 2687 2599 3017
42 WAFER 2475 25 2830 3118 3272 3184 3602
LUG 2700 25 3055 3343 3497 3409 3827
48 WAFER 2815 25 3170 3458 3612 3524 3942
LUG 3085 25 3440 3728 3882 3794 4212
NOTES: 1. The weights of actuators are without handwheel
2. DA = Double Acting / SR = Spring Return
150 Class Assemblies
Actuator Type
RC210
DA/SR
RC220
DA/SR
RC230
DA/SR
RC240
DA/SR
RC250
DA/SR
RC260
DA/SR
RC270
DA/SR
RC280
DA/SR
RC88
DA/SR
RC90 &
100 DA
RC90 &
100 SR
33
Actuator
1.5 1.5 2.5 2.5 6.5 6.5 26 26 250 185 66 22
Handwheel Weights
18 | GE Oil & Gas
Actuator Type Valve
Wt
Brack-
et WT
RC210 RC220 RC230 RC240 RC250 RC260 RC270 RC280 RC88 RCI90 RCG100 33 Actuator
Valve
Size
Type DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR Yoke
Wt
DA DA
3.1 4 4 5.85 810.4 10.6 15.5 20.4 26.8 27 40 69 69 89 142 162 330 618 772 684 1102 32 85
2 WAFER 8 12 23.1 24 24 25.85 28 30.4 30.6 35.5 24 64 117
LUG 11 12 26.1 27 27 28.85 31 33.4 33.6 38.5 24 67 120
3 WAFER 11 12 27.1 28 28 29.85 32 34.4 34.6 39.5 24 68 121
LUG 13 12 32.1 33 33 34.85 37 39.4 39.6 44.5 24 73 126
4 WAFER 17 12 33 34.85 37 39.4 39.6 44.5 24 73 126
LUG 25 2 40 41.85 44 46.4 46.6 51.5 24 80 133
6 WAFER 30 12 50 52.4 52.6 57.5 62.4 68.8 69 82 24 139
LUG 35 12 69 71.4 71.4 76.5 81.4 87.8 88 101 24 158
8 WAFER 44 12 79.5 84.4 90.8 91 104 133 133 24 161
LUG 48 12 107.5 112.4 118.8 119 132 161 161 24 189
10 WAFER 71 14 122.4 128.8 129 142 171 171 191 244
LUG 191 14 149.4 155.8 156 169 198 198 218 271
12 WAFER 110 14 194 207 236 236 256 309
LUG 127 14 240 253 282 282 302 355
14 WAFER 135 16 328 341 370 370 390 443 463 631
LUG 183 16 367 380 409 409 429 482 502 370
16 WAFER 182 20 425 425 445 498 518 686 974 1128 1040 1458
LUG 250 20 490 490 510 563 583 751 1039 1193 1105 1523
18 WAFER 234 20 482 482 502 555 575 743 1031 1185 1097 1515
LUG 305 20 606 606 626 679 699 867 1155 1309 1221 1639
20 WAFER 320 20 619 672 692 860 1148 1302 1214 1632
LUG 414 20 844 897 917 1085 1373 1527 1439 1857
24 WAFER 505 25 847 900 920 1088 1376 1530 1442 1860
LUG 702 25 1134 1187 1207 1375 1663 1817 1729 2147
30 WAFER 925 25 1932 2100 2388 2542 2454 2872
LUG 1130 25 2332 2500 2788 2942 2854 3272
300 Class Assemblies
Weights (lbs)
Actuator Type Valve
Wt
Brack-
et WT
RC210 RC220 RC230 RC240 RC250 RC260 RC270 RC280 RC88 RCI90 RCG100 33 Actuator
Valve
Size
Type DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR DA SR Yoke
Wt
DA DA
3.1 4 4 5.85 810.4 10.6 15.5 20.4 26.8 27 40 69 69 89 142 162 330 618 772 684 1102 32 85
2 WAFER 8 12 26.1 27 27 28.85 31 33.4 33.6 38.5 24 67 120
LUG 11 12 28.1 29 29 30.85 33 35.4 35.6 40.5 24 69 122
3 WAFER 11 12 28.1 29 29 30.85 33 35.4 35.6 40.5 24 69 122
LUG 13 12 33.1 34 34 35.85 38 40.4 40.6 45.5 24 74 127
4 WAFER 17 12 46 47.85 50 52.4 52.6 57.5 24 86 139
LUG 25 2 68 69.85 72 74.4 74.6 79.5 24 108 161
6 WAFER 30 12 62 64.4 64.6 69.5 74.4 80.8 81 94 24 151
LUG 35 12 105 107.4 107.6 112.5 117.4 123.8 1224 137 24 194
8 WAFER 44 12 99.5 104.4 110.8 111 124 153 153 24 181
LUG 48 12 154.5 159.4 165.8 166 197 208 208 24 236
10 WAFER 71 14 204.4 210.8 211 224 253 253 273 326 346 514 802 956 868 1286
LUG 191 14 267.4 273.8 274 274 316 315 336 389 409 577 865 1019 931 1349
12 WAFER 110 14 286 299 328 328 348 401 421 589 877 1031 943 1361
LUG 127 14 420 433 462 462 482 535 555 723 1011 1165 1077 1495
16 WAFER 182 20 1255 1255 1275 1328 1348 1516 1804 1958 1870 2288
LUG 250 20 1255 1255 1275 1328 1348 1516 1804 1958 1870 2288
NOTES: 1. The weights of actuators are without handwheel
2. DA = Double Acting / SR = Spring Return
600 Class Assemblies
39003 Series High Performance Butterfly Valves (HPBV) | 19
Dimensions
Model 34 (RC) Actuators - Dimensional Dat
Double Acting
Sizes 210 thru 280
Spring Return
Sizes 210/230/250/270
Spring Return
Sizes 220/240/260/280
Double Acting
Size 100
Spring Return
Sizes 100
Double Acting
Size 88
Spring Return
Sizes 88
20 | GE Oil & Gas
39003 Series High Performance Butterfly Valves (HPBV) | 21
Model 39003 Butterfly Valve Table
Valve
Size
Wafer Lug B C D
Thread
Size
# of
Holes
Bolt
Circle
A* A** E F G**
ANSI Class 150
2 3.00 3.00 10.25 1.75 1.06 5/8-11 4 4.75
3 3.00 3.38 11.00 1.92 1.20 5/8-11 4 6.00
4 3.50 4.13 11.75 2.13 1.26 5/8-11 8 7.50
6 4.88 5.12 13.00 2..31 1.38 5/8-11 8 9.50
8 5.88 6.01 14.13 2.50 1.49 5/8-11 8 11.75
10 6.88 7.88 14.88 2.81 1.70 3/4-10 12 14.25
12 9.50 9.50 16.63 3.23 1.86 3/4-10 12 17.00
14 11.07 11.07 17.25 3.62 2.19 7/8-9 12 18.75
16 12.05 12.05 22.69 4.00 2.31 7/8-9 16 21.25
18 13.18 13.18 24.00 4.50 2.45 1-8 16 22.75
20 13.94 13.94 25.13 5.00 2.94 1-8 20 25.00
24 16.44 16.44 27.25 6.06 3.12 11/8-8 20 29.50
30 22.73 22.73 3.62 6.75 3.53 11/8-8 28 36.00
36 32.11 32.11 38.50 8.38 4.34 11/4-8 32 42.75
42 35.62 35.62 44.00 9.25 5.03 11/4-8 36 49.50
48 38.25 38.25 47.25 10.62 5.62 11/4-8 44 56.00
ANSI Class 300
2 3.00 3.00 1025 1.75 1.06 5/8-11 8 5.00
3 3.00 3.38 11.00 1.92 1.20 3/4-10 8 6.63
4 3.50 4.12 11.75 2.13 1.25 3/4-10 8 7.88
6 5.12 5.50 13.00 2.29 1.38 3/4-10 12 10.63
8 5.88 7.28 14.14 2.88 1.54 7/8-9 12 13.00
10 7.38 7.88 15.38 3.25 1.70 1-8 16 15.25
12 10.50 10.50 21.00 3.62 1.86 11/8-8 16 17.75
14 14.57 14.57 22.38 4.62 2.48 11/8-8 20 20.25
16 16.32 16.32 24.00 5.25 2.59 11/4-8 20 22.50
18 17.26 17.26 25.13 5.88 3.03 11/4-8 24 24.75
20 18.49 18.49 26.39 6.31 3.24 11/4-8 24 27.00
24 21.67 21.67 29.38 7.19 3.62 11/2-8 24 32.00
30 30.50 30.50 38.88 8.88 4.39 13/4-8 28 39.25
ANSI Class 600
3 3.00 3.00 11.00 2.12 1.20 3/4-10 8 6.63
4 4.62 4.62 12.00 2.50 1.40 7/8-9 8 8.50
6 5.56 6.75 13.62 3.06 1.66 1-8 12 11.50
8 7.38 8.03 15.13 4.00 1.85 11/8-8 12 13.75
10 13.25 13.25 19.00 4.62 2.00 11/4-8 16 17.00
12 14.67 14.67 22.63 5.50 2.53 11/4-8 20 19.25
16 - 18.87 30.00 7.00 3.50 11/2-8 20 23.75
Model 34 (RC) Actuator Table
Size H J K L M N P Q
Spring Return
RC210 1.8 5.7 3.7 11.4 7.1 2.3 2.9 1.3
RC220 5.7 5.7 3.7 11.4 7.1 2.3 2.9 1.3
RC230 2.6 7.7 5.0 13.4 7.9 2.9 4.1 1.9
RC240 7.7 7.7 5.0 13.4 7.9 2.9 4.1 1.9
RC250 3.5 11.2 6.9 19.7 12.6 3.8 5.7 2.7
RC260 11.2 11.2 6.9 19.7 12.6 3.8 5.7 2.7
RC270 5.7 20.1 10.9 31.5 15.7 6.1 8.7 4.3
RC280 20.5 20.5 10.9 31.5 15.7 6.1 8.7 4.3
RC88 20.5 37.9 19.5 9.1 19.5 39.8 8.7 4.3
RC100 33.5 33.5 19.0 58.0 31.5 10.7 13.8 6.9
Double Acting
RC210 1.8 3.9 3.7 11.4 7.1 2.3 2.9 1.3
RC220 3.9 3.9 3.7 11.4 7.1 2.3 2.9 1.3
RC230 2.6 5.3 5.0 13.4 7.9 2.9 4.1 1.9
RC240 5.3 5.3 5.0 13.4 7.9 2.9 4.1 1.9
RC250 3.5 7.5 6.9 19.7 12.6 3.8 5.7 2.7
RC260 7.5 7.5 6.9 19.7 12.6 3.8 5.7 2.7
RC270 5.7 11.8 10.9 31.5 15.7 6.1 8.7 4.3
RC280 12.2 12.2 10.9 31.5 23.6 6.1 8.7 4.3
RC88 12.2 29.6 19.5 9.1 19.5 39.8 8.7 4.6
RC100 20.5 20.5 19.0 58.0 31.5 10.7 13.8 6.9
Model 33 Actuator Table
Size H J K L M N P Q
CL 150
3 13.00 11.50 - - - - - -
4 13.00 11.50 - - - - - -
6 17.50 15.20 - - - - - -
8 17.50 15.20 - - - - - -
CL 300
313.00 11.50 - - - - - -
4 13.00 11.50 - - - - - -
6 17.50 15.20 - - - - - -
8 17.50 15.20 - - - - - -
* - Dimensions apply to wafer valves only
** - Dimensions apply to lugged valves only
Dimensions
Model 33 Actuator - Dimensional Data
22 | GE Oil & Gas
Notes
39003 Series High Performance Butterfly Valves (HPBV) | 23
Notes
* Trademark of General Electric Company
Other company names and product names used in this document are the registered trademarks
or trademarks of their respective owners.
© 2014 General Electric Company. All rights reserved.
BELGIUM
Phone: +32-2-344-0970
Fax: +32-2-344-1123
BRAZIL
Phone: +55-11-2146-3600
Fax: +55-11-2146-3610
CHINA
Phone: +86-10-5689-3600
Fax: +86-10-5689-3800
FRANCE
Courbevoie
Phone: +33-1-4904-9000
Fax: +33-1-4904-9010
GERMANY
Ratingen
Phone: +49-2102-108-0
Fax: +49-2102-108-111
INDIA
Mumbai
Phone: +91-22-8354790
Fax: +91-22-8354791
New Delhi
Phone: +91-11-2-6164175
Fax: +91-11-5-1659635
ITALY
Phone: +39-081-7892-111
Fax: +39-081-7892-208
JAPAN Chiba
Phone: +81-43-297-9222
Fax: +81-43-299-1115
KOREA
Phone: +82-2-2274-0748
Fax: +82-2-2274-0794
MALAYSIA
Phone: +60-3-2161-0322
Fax: +60-3-2163-6312
MEXICO
Phone: +52-55-3640-5060
THE NETHERLANDS
Phone: +0031-15-3808666
Fax: +0031-18-1641438
RUSSIA
Veliky Novgorod
Phone: +7-8162-55-7898
Fax: +7-8162-55-7921
Moscow
Phone: +7 495-585-1276
Fax: +7 495-585-1279
SAUDI ARABIA
Phone: +966-3-341-0278
Fax: +966-3-341-7624
SINGAPORE
Phone: +65-6861-6100
Fax: +65-6861-7172
SOUTH AFRICA
Phone: +27-11-452-1550
Fax: +27-11-452-6542
SOUTH and CENTRAL
AMERICA and the CARIBBEAN
Phone: +55-12-2134-1201
Fax: +55-12-2134-1238
SPAIN
Phone: +34-93-652-6430
Fax: +34-93-652-6444
UNITED ARAB EMIRATES
Phone: +971-4-8991-777
Fax: +971-4-8991-778
UNITED KINGDOM
Wooburn Green
Phone: +44-1628-536300
Fax: +44-1628-536319
UNITED STATES
Massachusetts
Phone: +1-508-586-4600
Fax: +1-508-427-8971
Corpus Christi, Texas
Phone: +1-361-881-8182
Fax: +1-361-881-8246
Deer Park, Texas
Phone: +1-281-884-1000
Fax: +1-281-884-1010
Houston, Texas
Phone: +1-281-671-1640
Fax: +1-281-671-1735
DIRECT SALES OFFICE LOCATIONS
GEA20238A 07/2014

Navigation menu