GemTek Technology WIXS-165 WiMAX Indoor CPE User Manual User s manual
Gemtek Technology Co., Ltd. WiMAX Indoor CPE User s manual
Manual
User Manual Gemtek WiMAX Modem Manual Version: 1.1 Manual Date: Feb. 20 2009 Software Version: R4.6.0.0-17743-v5.7.0 Software Date: Feb. 20 2009 CONTENTS Chapter 1 Overview ..................................................................1-1 1.1. Indoor CPE............................................................................................. 1-1 1.2. Outdoor CPE.......................................................................................... 1-2 Chapter 2 WEB-GUI.................................................................2-3 2.1. System Configuration Login.................................................................. 2-3 2.2. 2.3. 2.4. 2.5. System Logout ....................................................................................... 2-6 Account .................................................................................................. 2-7 Date ........................................................................................................ 2-8 Language................................................................................................ 2-9 2.6. Scanner................................................................................................. 2-10 2.7. 2.8. 2.9. 2.10. Authentication...................................................................................... 2-12 Bridge Mode ........................................................................................ 2-14 NAT Mode ........................................................................................... 2-15 Firewall ................................................................................................ 2-16 2.11. 2.12. 2.13. 2.14. DHCP Server........................................................................................ 2-18 NAT ALG............................................................................................. 2-20 Port Forwarding ................................................................................... 2-21 Port Trigger .......................................................................................... 2-22 2.15. DDNS................................................................................................... 2-23 2.16. TR-069 ................................................................................................. 2-25 2.17. SNMP................................................................................................... 2-27 2.18. Log ....................................................................................................... 2-28 2.19. Upgrade................................................................................................ 2-29 2.20. 2.21. Recovery .............................................................................................. 2-31 Reboot .................................................................................................. 2-32 FIGURES Figure 1-1 Figure 1-2 Figure 2-1 Indoor CPE Front Panel LED ............................................... 1-1 Outdoor CPE installation ...................................................... 1-2 Login Page ............................................................................ 2-3 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 WiMAX Status ...................................................................... 2-4 WiMAX Status-Service Flow ............................................... 2-4 Network Status ...................................................................... 2-5 Device Status......................................................................... 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Logout ................................................................................... 2-6 Account ................................................................................. 2-7 Date ....................................................................................... 2-8 Language ............................................................................... 2-9 Figure 2-10 Scanner with Bandwidth range 6~10MHz........................ 2-10 Figure 2-11 Scanner with Bandwidth range 3~5MHz ...........................2-11 Figure 2-12 Authentication ................................................................... 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Authentication-View Certificates...................................... 2-13 Bridge Mode...................................................................... 2-14 NAT Mode......................................................................... 2-15 Firewall ............................................................................. 2-16 Figure 2-17 Figure 2-18 Figure 2-19 Figure 2-20 Firewall Filter.................................................................... 2-17 DHCP Server Enabled....................................................... 2-18 DHCP Server Disabled...................................................... 2-19 NAT ALG .......................................................................... 2-20 Figure 2-21 Figure 2-22 Figure 2-23 Figure 2-24 Figure 2-25 Port Forwarding ................................................................ 2-21 Port Trigger ....................................................................... 2-22 DDNS Enabled.................................................................. 2-23 DDNS Disabled................................................................. 2-24 TR-069 .............................................................................. 2-26 Figure 2-26 Figure 2-27 Figure 2-28 TR-069-Certificate File Upload ........................................ 2-26 SNMP enabled................................................................... 2-27 SNMP disabled.................................................................. 2-27 Figure 2-29 Figure 2-30 Figure 2-31 Figure 2-32 Figure 2-33 Log .................................................................................... 2-28 Web/FTP Upgrade............................................................. 2-29 Web Upgrade Summary .................................................... 2-30 TFTP Upgrade................................................................... 2-30 Recovery ........................................................................... 2-31 ii Figure 2-34 Figure 2-35 Reboot Button ................................................................... 2-32 Reboot Confirmation......................................................... 2-33 iii Chapter 1 Overview This chapter describes the panel function and installation procedure for the CPE. 1.1. Indoor CPE Front Panel LED Power LED: ON: power on LAN LED: ON: connect OFF: power fail OFF: disconnect Blinking: data transmit When the CPE powers on, the LED indicates the CPE states as follow. Only Red LED is Blinking: synchronization Only Yellow LED is Blinking: authentication Only Green LED is Blinking: DHCP client negotiation After the CPE has connected to the base station, the signal strength LED are defined as follow. Only Red LED is ON: the signal is weak. (CINR<8dB) Yellow LED is ON: the signal strength is medium. (8dB≤CINR<15dB) Green LED is ON: the signal strength is good. (15dB≤CINR) Figure 1-1 Indoor CPE Front Panel LED 1-1 Rear Panel Power jack: DC 12V / 1.5A LAN port: 10/100Base-TX Reset button: To reboot the CPE 1.2. Outdoor CPE Power Injector – Power Over Ethernet 802.3af compliant LAN port: 10/100Base-TX Figure 1-2 Outdoor CPE installation 1-2 Chapter 2 WEB-GUI This chapter describes how to configure the CPE in order to connect to the base station. 2.1. System Configuration Login The CPE will enable a DHCP server by default. Computers or network devices connected to its LAN side can get IP address automatically from CPE. If you disable CPE’s DHCP server by yourself, set the IP address, netmask, and gateway as following. IP address: 10.1.1.x, 1 ≤ x ≤ 253 Netmask: 255.255.255.0 Gateway: 10.1.1.254 Connect to http://10.1.1.254/ with a browser, and you will see a webpage such as the one shown in Figure 2-1. The administrator username and password are as shown below: Username: admin Password: admin Gemtek CPE also support multi-level user login. Please contact with Gemtek to define multi-user features. Figure 2-1 Login Page 2-3 If there is no error, the user can login into the Status Page, and WiMAX Status, Network Status, and Device Status are as shown in Figure 2-2, Figure 2-3, Figure 2-4, and Figure 2-5. Figure 2-2 Figure 2-3 WiMAX Status WiMAX Status-Service Flow 2-4 Figure 2-4 Figure 2-5 Network Status Device Status 2-5 2.2. System Logout Press the “Logout” button as shown in Figure 2-6 to logout of the system and go back to the “Login” page as shown in Figure 2-1. Figure 2-6 2-6 Logout 2.3. Account Personalization Account The Account page is used for changing the password of the WEB-UI account as shown in Figure 2-7. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and the new configurations will take effect. Figure 2-7 2-7 Account 2.4. Date Personalization Date If the system date is not in the valid duration of the uploaded certificate file, the CPE will not pass the authentication from the base station. The system date of a CPE can be synchronized with the PC that is connected to its LAN side by clicking the “Synchronize with PC” button. The system date of a CPE can also be automatically updated by synchronizing time with an NTP server assigned manually by the user or from the DHCP server. The selection of different time zone and daylight saving option are available as well for different regions. Please refer to Figure 2-8 for more detail. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-8 2-8 Date 2.5. Language Personalization Language The Language page allows users to select one of the languages in the drop-down list for viewing the WEB-GUI as shown in Figure 2-9. After selecting the desired language, press the “Apply” button to view the WEB-GUI in the selected language. Figure 2-9 Language 2-9 2.6. Scanner WiMAX Scanner (can only be accessed by administrator) The Scanner page allows users to stop or start WiMAX connection with a BS by simply clicking the “start” or “stop” button in the “Start/Stop WiMAX” section. The “Channel Table” section lists all the channels that are stored in the channel table along with channel status associated to the channel used to connect the CPE to a BS. Users are allowed to add, remove, and edit channels in the channel table. Please refer to Figure 2-10 and Figure 2-11 for more detail. After changing the channel table, press the “Apply” button to write the new configurations into the CPE. If the “Bandwidth range” of the channel table is changed, then press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect; otherwise, just simply restart the system by using the “start” and “stop” button in the “Start/Stop WiMAX” section. Please note that when the CPE is connected to a BS, a green check will appear on the “Active” of the linked frequency in the “Channel Table” section as well as beside the small CPE icon on the top banner; otherwise, a red x will appear beside the small CPE icon on the top banner. Figure 2-10 Scanner with Bandwidth range 6~10MHz 2-10 Figure 2-11 Scanner with Bandwidth range 3~5MHz 2-11 2.7. Authentication WiMAX Authentication (can only be accessed by administrator) Users can enable or disable the authentication by selecting one of the two methods supported, EAP-TLS and EAP-TTLS, or by selecting none in “Phase 1” field. Users can also choose one of five key encoding methods listed in “Phase 2”. Identity, username, and password should be entered respectively as agreed upon with the BS, if authentication is required. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Certificates required for authentication can be uploaded in the “Certificate File Upload” section. Contents of the certificates that are currently in the CPE can be viewed in details by clicking “View CA Certificate” as shown in Figure 2-13. Note that the only certificate format supported is PEM (Privacy Enhanced Mail, Base64 encoded DER certificate). Please confirm the format before uploading. Certificates in the CPE can also be deleted by pressing the “Delete” button. Please refer to Figure 2-12 for more details. Figure 2-12 Authentication 2-12 Figure 2-13 Authentication-View Certificates 2-13 2.8. Bridge Mode Networking Bridge/NAT Mode Bridge mode is enabled by simply selecting “Bridge Mode” as shown in Figure 2-14. By selecting “Static” IP type, users can manually assign the “IP address” and “netmask”. The “IP address” and “netmask” can also be automatically assigned by the DHCP server by selecting “DHCP” IP type. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and go to “Management Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-14 Bridge Mode 2-14 2.9. NAT Mode Networking Bridge/NAT Mode NAT mode is enabled by simply selecting “NAT Mode” as shown in Figure 2-15. By selecting “Static” WAN IP type, users can manually assign the “WAN IP address”, “WAN netmask”, and “WAN gateway”. The “WAN IP address”, “WAN netmask”, and “WAN gateway” can also be automatically assigned by the DHCP server by selecting “DHCP” WAN IP type. Users can also configure “LAN IP address”, “LAN netmask”, and “MTU”, which should be between 68 and 1500. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and go to “Management Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-15 NAT Mode 2-15 2.10. Firewall Networking Firewall (can only be accessed by administrator) The “CPE Access Control” section of this page gives users the ability to allow or deny web/telnet access from WAN. By enabling and identifying a DMZ host, an external attacker only has access to the DMZ host, rather than the entire private network at the CPE’s back end. Furthermore, the redirection of ICMP can also be enabled. The “Firewall Filter” section of this page is used to filter incoming network traffic based on MAC, IP, protocol, TCP/UDP port and interface. Please refer to Figure 2-16 and Figure 2-17 for more details. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-16 2-16 Firewall Figure 2-17 Firewall Filter 2-17 2.11. DHCP Server Networking DHCP Server DHCP server will automatically start up when the CPE is powered on if “DHCP server” is enabled. If enabled, this page shows the previous configuration of the DHCP server as shown in Figure 2-18; otherwise, it shows that the DHCP server is disabled as shown in Figure 2-19. Note that “Primary DNS” and “Domain Name” are required for DHCP server settings, and “Max lease time (seconds)” is between 1 and 99999999. Specific IP address can also be assigned to a specific MAC address in “Permanent Host Configuration” as shown in Figure 2-18. Please note that DHCP server is only applicable when the CPE is in NAT mode. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-18 DHCP Server Enabled 2-18 Figure 2-19 DHCP Server Disabled 2-19 2.12. NAT ALG Networking NAT ALG (can only be accessed by administrator) By selecting or deselecting the checkbox, users can enable or disable BSID authorization of SIP ALG as shown in Figure 2-20. With it enabled, BSID can be used in SIP authentication to decide if the ATA is within the service area. Please note that NAT ALG is only applicable when the CPE is in NAT mode. After changing the configuration, press the “Apply” button to write the new configuration into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-20 NAT ALG 2-20 2.13. Port Forwarding Networking Port Forwarding Port forwarding redirects incoming network traffic from pre-defined “WAN Port” range to pre-defined “LAN IP Address” and “LAN Port” range. Users are allowed to add, remove, edit, enable, and disable port forwarding rules here as shown in Figure 2-21. Please note that port forwarding is only applicable when the CPE is in NAT mode. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-21 Port Forwarding 2-21 2.14. Port Trigger Networking Port Trigger Port trigger dynamically opens port forwarding from a pre-defined WAN “Forwarding Port” range to a pre-defined LAN “Forwarding Port” range when a client on the local network makes an outgoing connection to a predetermined “Trigger Port” range. Users are allowed to add, remove, edit, enable, and disable port trigger mappings here as shown in Figure 2-22. Please note that port trigger is only applicable when the CPE is in NAT mode. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-22 Port Trigger 2-22 2.15. DDNS Networking DDNS By selecting or deselecting the checkbox, users can enable or disable DDNS as shown in Figure 2-23 and Figure 2-24. To enable DDNS, registration with at least one of the seven service providers is required, and can be done by clicking the “Sign Up” hyperlink and following the procedures. Enter the hostname, username, and password you have registered with the service provider and press the “Apply” button to save the changes into the CPE. The CPE will be able to notify the selected domain name server to change the active DNS configuration of its configured hostnames and addresses in real time by using the Internet Protocol Suite after pressing “Reboot” as shown in Figure 2-35. Figure 2-23 DDNS Enabled 2-23 Figure 2-24 DDNS Disabled 2-24 2.16. TR-069 Management TR-069 (can only be accessed by administrator) TR-069 client will automatically start up when the CPE is operational if the “TR-069 Active Flag” is enabled. The “ACS Server URL” is the URL used by TR-069 client to connect to the ACS server, and TR-069 client uses the “ACS Username” and “ACS Password” to login the ACS Server. When the “Inform Enable” is enabled, TR-069 client will periodically query the ACS server according to the “Inform Interval”. The ACS server can also use the “Connection Request Username” and “Connection Request Password” to connect to the CPE and get/set parameter via connection request mechanism. Nevertheless, all of the above parameters will be overwritten if Option-43 is activated. However, the parameters changed by Option-43 will not be saved into the CPE. In other words, all of the above parameters will be restored when the CPE reboots. TR-069 certificates required for HTTPS protocol can be uploaded in the “TR-069 Certificate File Upload” section. Note that the only certificate format supported is PEM (Privacy Enhanced Mail, Base64 encoded DER certificate). Please confirm the format before uploading. Please refer to Figure 2-25 and Figure 2-26 for more details. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE. If only the “Inform Enable” and/or “Inform Interval” have been changed, then do nothing and the change will take effect in the next inform interval; otherwise press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. 2-25 Figure 2-25 Figure 2-26 TR-069 TR-069-Certificate File Upload 2-26 2.17. SNMP Management SNMP (can only be accessed by administrator) This page is used to enable disable SNMP server as shown in Figure 2-27 and Figure 2-28. When SNMP is enabled, the community string of the SNMP server can be changed. After setting the configurations of these fields, press the “Apply” button to write the new configurations into the CPE and press “Reboot” as shown in Figure 2-35, to reboot the system in order for the new configurations to take effect. Figure 2-27 SNMP enabled Figure 2-28 SNMP disabled 2-27 2.18. Log Management Log (can only be accessed by administrator) This page displays the system message log as shown in Figure 2-29. Figure 2-29 2-28 Log 2.19. Upgrade Management Upgrade (can only be accessed by administrator) To perform web upgrade, press the “Brows…” button to choose the firmware file in the computer in the “Web Upgrade” section, and press the “Upload” button to upload the file into the CPE. Please refer to Figure 2-30 for more details. After the firmware file is uploaded, the summary will be displayed as shown in Figure 2-31. Then press the “Apply” button to upgrade the firmware. This upgrade procedure takes about 3 minutes and reboots the CPE afterwards automatically. To perform FTP upgrade, input the FTP server IP address, FTP username and password, firmware file path, and firmware file name. Press the “Upgrade” button in the “FTP Upgrade” section and the CPE will start to download the firmware from the FTP server and upgrade. The CPE will automatically reboot itself afterwards. Please refer to Figure 2-30 for more details. To perform TFTP upgrade, input the TFTP server IP address and the firmware file path and press the “Upgrade” button in the “TFTP Upgrade” section. It takes about 3 minutes for a CPE to download the firmware from a TFTP server and upgrade it. The CPE automatically reboots itself afterwards. Please refer to Figure 2-32 for more details. Figure 2-30 Web/FTP Upgrade 2-29 Figure 2-31 Web Upgrade Summary Figure 2-32 TFTP Upgrade 2-30 2.20. Recovery Management Recovery (can only be accessed by administrator) Both current firmware version and previous firmware version are shown in the “Firmware Rollback” section. Firmware rollback can be performed by pressing the “Rollback” button. Device configuration file that includes files such as, .configdb and ddns.conf, can be uploaded from PC to CPE as well as downloaded from CPE to PC. To restore a CPE back to factory default settings, just press the “Factory Default” button in the “Factory Default Settings” section. Please refer to Figure 2-33 for more details. Figure 2-33 2-31 Recovery 2.21. Reboot Press the “Reboot” and “Yes” buttons to reboot the system. Please refer to Figure 2-35 and Figure 2-35 for more details. Figure 2-34 Reboot Button 2-32 Figure 2-35 Reboot Confirmation Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this 2-33 equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Due to the essential high output power natural of WiMAX device, use of this device with other transmitter at the same time may exceed the FCC RF exposure limit and such usage must be prohibited (unless such co-transmission has been approved by FCC in the future). 2-34
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : 3.1-701 About : a1434727-8d68-11de-0000-715f92e9cc94 Producer : GPL Ghostscript 8.63 Keywords : Modify Date : 2009:08:17 17:51:42+08:00 Create Date : 2009:08:17 17:04:18+08:00 Creator Tool : PDFCreator Version 0.9.7 Metadata Date : 2009:08:17 17:51:42+08:00 Document ID : a1434727-8d68-11de-0000-715f92e9cc94 Instance ID : uuid:4c963a26-9f45-4891-b1d9-4363e427bb74 Format : application/pdf Title : User's manual Creator : Joy Description : Page Count : 38 Subject : Author : JoyEXIF Metadata provided by EXIF.tools