GemTek Technology WMDD209 Lora module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3369811
Application ID	WMHfoNgTvOq1hAmHC9IT2g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	74.34kB (929230 bits)
Date Submitted	2017-04-25 00:00:00
Date Available	2017-04-26 00:00:00
Creation Date	2017-10-26 03:15:26
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-26 03:15:26
Document Title	Users Manual

WMDD-209 LoRa Module User
Manual
Version : 1.0.1
Release History
Release date
Release version
2017/04/24
1.0.1
Main Delta
1. Initialize the document
Arthur
Owen Hsu
1. Hardware Figure
The following are the hardware picture and its pin definition.
(Figure 1)
(Figure 2)
Before using the module, you must have power supply, you can have a power supply
by connecting usb like following picture.
(Figure 3)
After power on, the user can access the module by AT command.
In WMDD-209, the user have to use UART1 to send / receive data to / from
the node You can refer to the following pic and figure 2 to connect UART for
using the console.
(Figure 4)
2.
Configuration setting and related
command
ABP mode:
In ABP mode, the user needs to configure 3 parameters, which are
device address, network session key, application session key.
The following AT commands are for end user to set the 3
parameters on WMDD-209.
AT+ECHO=1
/*show the
characters user input*/
AT+CMODE=1
/*set node to ABP mode*/
AT+CDEVADDR=
/*set device address*/
AT+CNWKSKEY= /*set network session
key*/ AT+CAPPSKEY= /*set
application session key*/
AT&W
/*save the
configuration*/
ATZ
/*reboot the node*/
If the gateway is set well too, users can follow the instruction to
send packets.
AT+DTTX
device address*/
/*quick send, the message is
AT+DTX=, AT+DTX=2,"Hi"
AT+DTX=11,"Hello World"
OTAA mode:
In OTAA mode, the user needs to prepare 3 parameters,
which are application EUI, device EUI and application key.
The following AT commands are for end user to set the 3
parameters above on WMDD-209.
AT+ECHO=1
/*show the
characters user input*/
AT+CMODE=0
/*set node to OTAA
mode*/ AT+CDEVEUI= /*set device address*/
AT+CAPPEUI=
/*set network session
key*/ AT+CAPPKEY= /*set application session
key*/ AT&W
/*save the
configuration*/
ATZ
/*reboot the node*/
If the gateway is set well too, users can follow the instruction to
send packets.
AT+DTTX
device address*/
or
AT+DTX=, AT+DTX=2,"Hi"
AT+DTX=11,"Hello World"
/*quick send, the message is
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the
US/CANADA
Operation of this device is restricted to indoor use only
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna,
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC
ID:”MXF-WMDD209”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:68b7b674-9c53-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:08 23:40:44Z
Create Date                     : 2017:07:08 23:40:44Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:68b7b674-9c53-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled

EXIF Metadata provided by EXIF.tools