Gemel Italia S p A TXSHS User Manual 33217

Download:
Mirror Download [FCC.gov]
Document ID	33217
Application ID	SFDH+a30s2vfysV6un2bWQ==
Document Description	8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.98kB (112193 bits)
Date Submitted	1999-04-20 00:00:00
Date Available	1999-04-29 00:00:00
Creation Date	2001-06-28 14:19:02
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-06-28 14:19:07
Document Title	33217.pdf
Document Author:	VicodinES /CB /TNN

FCC ID: F6QTXSHS
EXHIBIT 4
OPERATING INSTRUCTIONS
FOUR (4) PAGES OF OPERATING INSTRUCTIONS
FOLLOW THIS SHEET
OPERATING INSTRUCTIONS
FCC ID: FGQTXSHS
EXHIBIT 4
Q xanppe
W of 036
For every amtlng cycle. the alarms ere Ilrnrmd h e meximun number oi:
6 Interventions due to each on the tollowing ceuen: '
~ eaddle protection (PS)
- saddlebeg protection (PB)
- stand protection (PC)
- Ignition attempt (T A)
- voltage drop. when elenn B armed (CA)
3 Interventions tor:
~ position control sensor (SP) (npfionei)
ALABMSLQBAEE
Afler disarming the alarm. the LED will ilash a number oi lime;
indicafing that one or more acoustic elerrne have occurred during
your absence To identify the alarm cause reier tr; both this note
and the abbreviations In the previous section The alarm wil store
these signals until either the Ignition Ie tumed on or the alarm Ie
reamed,
The alarm has Internal batteries and sounds It the battery wires are an or disconnected.
When the battery Is recomected. the sound will stop within an seoende after being connected.
The eutoieed cycle is 30 maids on and to eeconde oft. whim Ie repeated tor 5 minuiee.
In autoiead mode. which is only ecn‘vated when the alarm is armed. the direction indicators do not
work
During the arming period (the tlrsi ts Ms), any lack of voltage is indicated by the buzzer
reputedly giving oil a monotone sound until It rune down, alter which the alarm will give off a two-
tone sotmdr
WW
Automatic arming means that the motorcycle le protected even when the user targets to arm the
alarm. Ttie to required by a number of Hemdegetion bodies, and it is possible to erm and dieenn
using a remote-correct. These tell into two categories — passive engine Immebilisetien - passive
engine Immoblllsation and alarm system,
_(it 00an end enabled by programming)
After having removed the Ignition key. engine irrwnoolllsatton occurs emometiceity after 15 socerlde.
so prev-"find erry Illicit attempt at starting up the engine. By way of oontlrrmtion that the alarm Ie
armed them will be:
- one tlesh oi the direction Indicators
~ the huuervrill lound once
-ttte LED lightwilcome 0n- .
To disarm the alarm. touch the LED reader with the tip of the electronic key or press button A on the
remote control twice or:
Imert the Ignition key and touch the LED reader with the tip or the eiectronlc key or press Button A on
the remote oorrtfoL
(It enebled by programming)
After having removed the ignition key. engine Irnmohlllsation occurs amaman‘cally aiter15 seconds,
By way of confinmtion that the alarm he: been ermed there will be:
- one flash oi the direction Indicators
- the buzzerwill sound once
- the LED light wt! 90 out.
Peg. 9
Met a Miner 15 seconds. the alarm will be armed which will be oonllnned by:
- Mo flashes oithe direction hdlcetors
- Mo eounde oi the buzzard
At Ihll stage the engine inwnobilsetion and alarm system are armed. alter a turner t5 uoond: the
alarm wll be operative and the LED light will mnlv flesh. To disarm, touch the LED reader with the
tip at the electronic key or press button A on the remote-comet.
Passive arming is a function which is required by the homologelion bodies In various European
countries It is possible however to exclude. lotluet one cycle. the automatic aierrn arming Iunction In
accordance with personal requirements. To disable the passive arming Iellow this procedure:
- Remove the Ignition key within to seconds making the yellow wire negative.
- Arm and disarm the alarm using the electronic key.
Automatic arming will be restored the next time the alarm is armed using the electronic key or remote-
oontrei. or alter having turned the ignition key Irom ON to OFF.
MB. Engine tmmobillsation however. will be armed alter 15 seconds.
Note: WITH MOTORCYCLES THAT HAVE A POSITION “R" ON THE IGNITIONv IT IS SUFFICIENT
TO LEAVE THE KEV IN THAT POSITION TO PREVENT AUTOMATIC ARMING.
Wm
Frees button (A). Conflmretion that the alarm has been armed wil be Indicated by:
a Mo flashes oi the direction indicators;
- Mo eounda oi the bun-r
- the LED light will come on (Mar 15 seconds).
N.B. The acoustic alarm will be operative rs awards alter the alarm Is armed, during which time. it
the alarm Is activated tor any reason, the buzzer will sound onoe.
WW
To disarm the alarm. press button (A) Confirmation that the alarm has been disarrned will be
Indicated or
- one llnh oi the dlreclion Indicators:
- one sound of the buzzer
~ the LED Hm will go out.
MW
(acoustic alarm only)
This function to activated for 10 seconds by pressing button (B) 15 seconds alter armhg or dinnnlng
the alarm. It can be deactivated by pressing button (B) once again without altering the condition at the
alarm.
Wm
In accordance with current regulations or where parking motorcycles within hotel or hospital grounds
or where mooning “id motorcycles by terry, it to possible to arm the alarm and exclude the eiren.
To activate this function ioltow this procedure:
- With the ignition on. press button (A) on the remote-eentrot tor about 2 seconds (the LED will iiaah
anon)
- Turn oil the ignition within 10 seconds (alter which the lunctlon wil not be stored).
At title stage. alter arming, the siren will be excluded Iortha entire ON cycle. On disarming the alarm.
the lunctien will be automatically restored.
Page to
grammes
It is poeaible to disconnect the siren iunction Mdaarrnlnq the elem To do so, prose bulton (B).
TNellmtionddeanctaltertheccrmmoitt-ealam.
mm
In case of lose at the transmitter it la possible to disarm the alarm by using lira stored electronic key,
WW
To exclude the position control aaneor inflow this procedure:
- arm the alann.dur1ng which time (the tiral t5 seconds) piece button (B) on the tame-control.
- Confirmation that the exclulon hu occurred will be hdlcahd by:
4 3 flashes ot the direction lrrdioetora;
- 3 sounds ottha buzzer.
- 3 Hashes oi the LED llght.
The lent the battery is low may be Indicated In two ways.
- on dsarmlng the alarm, Instead of the normal buzzer Impulsee. they will be less awte,
- the LED on the remote-control will only light up tor a split aeoond (20 male). after Mitch it will not
light up again even it you go on pressing. ‘
WW
when tha battery Ia dead do not treat It as normal waste, but dlapaaa oi It In the spatial contain-re.
It is important that you replace the battery ‘n cloa- proxlnity to the motorcycle.
when repladnu IL remove the screws on the back and separate the two halves of
the case. Take out the dead battery and replace it with a new one.
when replachn batteries. the CR 2012 SV model Ia advisable (code 22120050).
~ Remove the screws on the back and the separate 1m two halves oi the case.
- When putting the new battery in place, make sure that the battery does NOT
come Into contact with any ot the remote-control! electrical components.
When you have replaced the battery, the LED on the remote-canoot will light up,
Carry out the reaynchronisetion procedure (see relevant paragraph).
BESINQHBQNLSAIJQM
It the remote-comm button is pressed for more than 256 time consecutively out oi the alerrn's
maximum capacity range, it will be necessary In carry out the reeynohroniaatlon procedure.
- press buttons (A) and (B) at the some time until the LED light goes out (approximately 10 seconds);
- release them and check to see that the LED light has come on and stays on;
- linaly, press any button within the range at the alarm.
You remote-control shoud now be raaynchronleed with your alarm.
ALAEILSXSEMIEQHNJSZMQJEKZAIIQNS
~ Arming time 15 second:
- Alarm time 30 seconds
- Manning time between one alarm and another 5 seconds
- Working temperature 40‘0 + BS'C
- Average rennin-control transmission distance to metres
~Tranamitter range > 25 Kb: (wide band)
amuse
~ Particular attention muat laken when washing the motorcycle. In auclr caaaa, protecting the alarm
from any direct waters lets is advisable.
- Do not molest the remote-control to any excessive sources at heat. water or knocke
- Installation and electrical connections must he carried out In accordance with the Instructions
aupplled by the manufacturer: furthermore, calling In an Installer er pmleaalonai la advisable tar
assembling the alarm.
Fag. It
FCC ID: FGQTXSHS
EXHIBIT 5
BLOCK DIAGRAM & CIRCUIT DESCRIPTION
Saw Filter
DESCRIPTION:
Digital encoder ICl keys SAW (SWFl) stabilized oscillator T1.
Low pass filter couples T1 to antenna formed as etched—circuit
track.
BLOCK DIAGRAHS & CIRCUIT
DESCRIPTIONS
FCC ID: F6QTXSHS
EXHIBIT 5
ws/ptlS/bmwalarm

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:06:28 14:19:02
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : VicodinES /CB /TNN
Title                           : 33217.pdf
Modify Date                     : 2001:06:28 14:19:07-04:00
Page Count                      : 5

EXIF Metadata provided by EXIF.tools