Generac Power Systems 0H7699 Generator Monitor Module User Manual Module Data Sheet V1

Download:
Mirror Download [FCC.gov]
Document ID	1388379
Application ID	WqA2hExR/ejh28cT9ukrFw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.65kB (120646 bits)
Date Submitted	2010-12-09 00:00:00
Date Available	2010-12-09 00:00:00
Creation Date	2010-11-02 16:45:09
Producing Software	Acrobat Distiller 9.4.0 (Windows)
Document Lastmod	2010-11-02 16:45:09
Document Title	Microsoft Word - Module Data Sheet V1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ahauck

Generac 0H7699 Wireless Module: Data Sheet/Manual
0H7699 module with connector for external antenna (see approved antennas listed below).
0H7699 module for wire antenna (see approved antennas listed below).
November 2, 2010
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
FCC Interference Statement (Part 15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general
population / uncontrolled exposure.
 Page 2
November 2, 2010
Section 7.1.5 of RSS-GEN
Operation is subject to the following two conditions:
1) this device may not cause interference, and
2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Section 7.1.4 of RSS-GEN
This device has been designed to operate with the antenna(s) listed below, and having a
maximum gain of 2.0 dB. Antennas not included in this list or having a gain greater than
2.0 dB are strictly prohibited for use with this device. The required antenna impedance is
50 ohms.
List of all Antennas Acceptable for use with the Transmitter
20AWG Insulated tinned-Cu wire 3.82in (97.0mm).
Nearson S467AH-915 (SMA rev polarity).
Section 7.1.5 of RSS-GEN
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that permitted for successful communication.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
 Page 3
November 2, 2010
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
INDUSTRY CANADA STATEMENTS
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that permitted for successful communication.
This device has been designed to operate with the antennas listed below, and having a
maximum gain of 2.0 dB. Antennas not included in this list or having a gain greater than
2.0 dB are strictly prohibited for use with this device. The required antenna impedance is
50 ohms.
List of all Antennas Acceptable for use with the Transmitter


20AWG Insulated tinned-Cu wire 3.82in (97.0mm).
Nearson S467AH-915 (SMA rev polarity).
OEM Responsibilities to comply with FCC and Industry Canada Regulations
The 0H7699 Module has been certified for integration into products only by OEM integrators
under the following conditions:
1. The transmitter module must not be co-located or operating in conjunction with
any other antenna or transmitter.
As long as the two conditions above are met, further transmitter testing will not be
required. However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain
configurations or co-location with another transmitter), then the FCC and Industry
Canada authorizations are no longer considered valid and the FCC ID and IC
 Page 4
November 2, 2010
Certification Number cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC and Industry Canada authorization.
End Product Labeling
The 0H7699 Module is labeled with its own FCC ID and IC Certification Number. If the FCC
ID and IC Certification Number are not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display a
label referring to the enclosed module. In that case, the final end product must be labeled in a
visible area with the following:
“Contains Transmitter Module FCC ID: VDE-0H7699”
“Contains Transmitter Module IC: 8036A-0H7699”
or
“Contains FCC ID: VDE-0H7699”
“Contains IC: 8036A-0H7699”
The OEM of the 0H7699 Module must only use the approved antenna(s) listed above, which
have been certified with this module.
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module or change RF related parameters in the user
manual of the end product.
 Page 5
November 2, 2010
Specifications
Performance:
Operating Frequency
Outdoor RF line-of-sight range
Outdoor to Indoor (through wall) range
Transmit Power Output
Throughput Data rate
Receiver Sensitivity
ISM Band 902-928MHz
External dipole antennas: 430 ft (131 m)
100 ft to wall, 100 ft inside building (typical).
Range inside building will vary according to:
 Distance of outdoor transceiver from
outdoor/indoor interface (wall).
 Type of interface i.e. brick, aluminum
siding, stone, tinted windows using
metalized tint.
 Orientation of transceiver antennas (to
each other).
 Number and type of internal walls,
between transceivers, within building.
Internal antenna: -2.8 dBm
External dipole antenna -5.3 dBm
2400 baud
-102 dBm
Power Requirements:
Supply Voltage (Regulated)
Receive Current
Transmit Current
Standby Current
3 ± 0.15Vdc
13.6mA
25.4mA
< 500nA
General:
Dimensions
Weight
without SMA connector
with SMA connector
without SMA connector
Antenna Options
with SMA connector
Operating Temperature
1.25in x 1.05in x 0.16in
(32.0mm x 26.5mm x 4.2mm)
0.2oz (6g)
0.3oz (9g)
Insulated tinned-Cu wire 3.82in (97.0mm),
stripped 0.12in (3.0mm).
Nearson S467AH-915 (SMA rev polarity)
-40°C to +85°C
Agency Approvals:
FCC Part 15.249
Industry Canada (IC)
 Page 6
VDE-0H7699
8036A-0H7699

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : ahauck
Create Date                     : 2010:11:02 16:45:09-05:00
Modify Date                     : 2010:11:02 16:45:09-05:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.4.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - Module Data Sheet V1
Creator                         : ahauck
Document ID                     : uuid:2560af23-4b59-4f2d-937b-bc3b2d66a21e
Instance ID                     : uuid:2628b3f9-4e3d-4ffc-ba9f-310838a6068c
Page Count                      : 6

EXIF Metadata provided by EXIF.tools