General Infinity BXH-300 Bluetooth stereo headset User Manual BEC3100 QIG
General Infinity Ltd Bluetooth stereo headset BEC3100 QIG
User Manual
Antec BXH-300 QIG
Bluetooth™ Stereo Headset
BXH-300 is a headset that supports
wireless music streaming with
SBC and apt-X codec. By
connecting the headset to the PC
via a Bluetooth USB audio dongle,
the user can listen to music in
streaming mode. Also, the user can
listen to music by connecting the headset to the MP3 via a Bluetooth audio
adapter. The sports design of the headset with its light headband allow user to
enjoy sheer and unsurpassed comfort. It is perfect for travel entertainment or as
an add-on for your home entertainment system. People can switch to mobile
phone automatic or manually when there is an incoming call headset connect
with your cellular phone(with Bluetooth™ function) give you a safety way to
none stop communication in driving.
1 Headset Features
1: Backward button 2: Play/Pause
3: Forward button 4: Microphone
5: Volume up 6: Volume down
7: Power button (MFB) 8: micro USB
9: Phone button 10. Line-in Jack
1
2
3
5
6
4
4
5
4
7
5
8
5
9
5
10
05
Function Keys
Location
Keys
Function
Volume up
Volume up function
Volume down
Volume down function
Forward button
Play next song for AVRCP function
Backward button
Play previous song for AVRCP function
Play/Pause button
MFB button
Power on / off / three way call function
Phone button
General phone call function
LED indicators
Color
LED Status
Function
Blue
Status LED lights up steady
Standby(no connection )
Status LED flashes
Linked
Status LED and Charging LED
Flash alternative
Pairing state
Red
Charging LED flashes slowly
Low battery
Charging LED lights up steady
Charging (Indicator turns off when
charging is completed.)
2 Charge your headset
After opening the package, please make sure to do the following steps full charge
the headset by charge it at least 4 hours. The Red LED will be steady on when
charging. The LED will go off when battery is fully charged.
3 Power on or off your headset
Press MFB key about 3 seconds to power on the headset. When the headset
power on the blue led will flash 3 times and you can hear a rising tone. When
headset already power on, press MFB key about 3~5 seconds will power off the
headset. When the headset power off the red led will flash 3 times and you can
hear a falling tone.
4 Pairing device with your headset
Pairing headset to your Bluetooth™ mobile phone or other Bluetooth™ devices
for the first time only. The headset will remember paired device, so you don’t
need pair it every time. To put headset into pairing mode, press and hold the
MFB button for six seconds to wait for the Blue and red led flash alternative that
indicates the headset is into the paring mode. Operate your Bluetooth™ mobile
phone or other Bluetooth™ device to start Bluetooth™ function. Find the
headset “pulse”, press the pairing code “0000” The blue LED is start flashing,
the headset is in connected mode
5 Working in AV mode
When your headset connects a device with A2DP profile, you can listen to stereo
music from transmitter side to your headset. You can connect a USB dongle or
AV transmitter or cellular phone with A2DP profile supported. Almost A2DP
source device support AVRCP that can use play/pause, next track and pre track
function. If you use AV transmitter with 3.5mm audio jack then it doesn’t support
AVRCP function. Working in AV connection mode, you can
Short press Play/Pause key to toggle play/pause action
Short press Vol+ or Vol- to adjust volume
Short press forward or backward button to change songs
6 Working in headset mode
When your headset connect a device like cellular phone or a Bluetooth USB
dongle working with Bluetooth PC stack. Your headset can working in headset
mode. Working in headset mode, your headset can using 8 KHz channel to
transmit and receive voice data? You can use it as a Bluetooth mono headset to
talk phone call wirelessly. You also can connect PC with a USB dongle running
skype or massager talking with your headset.
Standby mode:
Short press MFB button key to init voice dial function
Double MFB button key to init last number redial function
Long press volume up and backward button to clear paired.
Incoming call (ring) mode:
Short press Phone button key to accept phone call
Long press Phone button key when hear a beep tone to reject call
In call active mode:
Short press Vol+ or Vol- to adjust volume
Long press Phone button key when hear a beep tone to toggle call
between headset and cellular phone
Short press MFB key to end call
Short press Vol+ or Vol- key to toggle mute microphone
7 Led statuses
POWER ON
Blue led flash 3 times
POWER OFF
Red led flash 3 times
PAIRING
Blue and red led flash alternatively
STANDBY MODE
Blue led steady On
AV ACTIVE MODE
Blue led flash twice every 2 seconds
HEADSET ACTIVE MODE
Blue led flash once every 2 seconds
LOW BATTERY INDICATION
Red led flash once 2 sec continuous
AUTO SHUTDOWN
Red led flash 3 times and power off (5 minutes no any
connection)
8 Troubleshooting
If the Bluetooth Headset does not work, try the following:
-Ensure connecting devices are charged
-Turn off all devices and then turn them on in order to shown in this guide
-Ensure devices are within 10 meter range
-Ensure the Headset is connected by check the blue LED flash
Note 1: Some A2DP source like 3.5mm interface transmitter cannot support
AVRCP profile, so it cannot do remote control function.
Note 2: Only cellular phone supports hands free profile can use voice dial, last
number redial, call transfer function
9 Statement
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power if such
function is available.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power if such
function is available.
Déclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour
les Etats-Unis et le Canada établies pour un environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction
aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que
possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie
la plus faible si une telle fonction est disponible.
For Taiwan 警語：
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法
規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用
電波輻射性電機設備之干擾。