Gentex MUAHL5 Universal Garage Door Opener User Manual

Gentex Corporation Universal Garage Door Opener Users Manual

Users Manual

 Programming and Information Guide Information on compatible products and video programming instructions are available at www.homelink.com Only press the transmitter button on the integrated garage door opener if there are no persons or objects present within the sweep of the garage door. People could otherwise be injured by the movement of the door. 1234 Integrated garage door opener on the rear-view miof this integrated garage door opener. rror Garage door remote control 5 is not part atteries in garage door remote control 5 before programming. e programming, clear all HomeLink memory by following the instructions in the "clearing memory" section (page 333) the ignition lock. ed garage door opener. Indicator lamp 1 lights up yellow. ntrol 5 towards buttons 2 to 4 on the rear-view mirror at a distance of 2 to 8 inches (5 to 20 cm). tton 6 on remote control 5 until indicator lamp 1 lights up green. If the indicator lamp 1 does not turn green, reposition the remote control 5 and repeat this step. To achieve the best result, insert new b•► For first tim•► Turn the SmartKey to position 2 in •► Press and release one of buttons 2 to 4 on the integrat•► Point remote co•► Press and hold buHomeLinkandtheHomeLinkhouseareregisteredtrademarksofGentexCorporation.
•► Release button 6 on remote control 5. •► Firmly press, and release the programmed button 2, 3, or 4 of the integrated garage door e the device. If the device activates, programming is complete. If the device does not activate, continue with "Synchronizing the Rolling Code." Your vehicle must be within range of the garage or gate opener drive. Make sure that neither cts are present within the sweep of the door or gate. A ladder and/or second person may simplify the following steps. •► Turn the SmartKey to position 2 in the ignition lock. •► At the garage door opener receiver (motor-head unit) in the garage, locate the “Learn” or e motor-head unit (see the Garage Door Opener manual to identify the “Learn Button”). •► Press the previously programmed transmitter button 2, 3, or 4 of the integrated garage door the device activates, programming is complete. Canadian radio frequency laws require a "break" (or interruption) of the transmission signals nals may not therefore last long enough for the integrated garage door opener to recognize the signal during programming. Comparable with follows: r a •► Press button 6 of the garage door remote control 5 for two seconds, then release it for two opener up to three separate times to activatSynchronizing the rolling code your vehicle nor any persons/objeObserve the safety notes when performing the rolling code synchronization. “Smart” Button. This can usually be found directly on thThere are typically 30 seconds to complete the next step. opener up to three separate times to activate the device. If Notes on programming the remote control after broadcasting for a few seconds. These sigCanadian law, some U.S. garage door openers also feature a “break.” If you live in Canada or have difficulties programming the garage door opener (regardless of where you live) when using the programming steps above, proceed as •► Press and hold one of transmitter buttons 2 to 4 of the integrated garage door opener. Afteshort time, indicator lamp 1 lights up yellow. •► Release the button. Indicator lamp 1 flashed yellow. seconds. •► Repeat this sequence on button 6 of remote control 5 until indicator lamp 1 lights up green.HomeLinkandtheHomeLinkhouseareregisteredtrademarksofGentexCorporation.
•► Continue with the other programming steps (see above). Problems when programming If you are experiencing problems programming the integrated garage door opener on the rear-view mirror, take note of the following instructions: 5. This increases the likelihood that garage door remote control 5 will transmit a strong and precise signal to the integrated garage door ote control 5 at varying distances and angles from the button you are programming. Try various angles at a distance between 0 and 8 inches (0 to 20 cm) or at the me garage door drive is available, repeat the same programming steps with this remote control. Before you perform the steps, make sure that new nt of time (the indicator lamp on the remote control goes out). Press button 6 on remote control again before transmission ends. reception/transmission. pening / closing the garage door egrated garage door opener performs the function of the garage door system's remote control. Please also read the operating instructions for the garage martKey to position 2 in the ignition lock. operate the garage door. ressed. The transmission is halted after a maximum of ten seconds and indicator lamp 1 lights up yellow. to position 2 in the ignition lock. llow. - Replace the batteries in garage door remote controlopener in the rear-view mirror. - When programming, hold remsame angle but at varying distances. - If another remote control for the sabatteries have been installed in the garage door remote control 5. - Note that some remote controls only transmit for a limited amou - Extend the antenna cable of the garage door opener unit. This can improve signal OAfter it has been programmed, the intdoor system. •► Turn the S•► Press button 2, 3 or 4 which you have programmed toThe transmitter will transmit a signal for as long as the transmitter button is being pPress button 2, 3, or 4 again if necessary. Clearing the memory •► Turn the SmartKey •► Press buttons 2 and 4. The indicator lamp lights up yeHomeLinkandtheHomeLinkhouseareregisteredtrademarksofGentexCorporation.
HomeLinkandtheHomeLinkhouseareregisteredtrademarksofGentexCorporation. green. nual, as part of Homologation regulations globally if applicable. l shall be written in the native language of the ountry of use. be mounted in the vehicle with only the button side of the device exposed to the nd user. ) and IC (Canada): ules part 15 and Industry Canada RSS-210. Operation is subject the following two conditions: (1) This device may not cause harmful interference, and (2) This limits set forth for an uncontrolled nvironment. End Users must follow the specific operating instructions for satisfying RF co-at Industry Canada technical specifications were met. •► Press and hold buttons 2 and 4 until the indicator lamp turnsThe following is required text to be included in the Vehicle Owner’s Ma *A general requirement is that the Owner’s Manuac The device is to e FCC (USA This device complies with FCC rtodevice must accept any interference that may be received including interference that may cause undesired operation. WARNING: The transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. This equipment complies with FCC radiation exposureeexposure compliance. This transmitter must be at least 20 cm from the user and must not belocated or operating in conjunction with any other antenna or transmitter. The term “IC:” before the certification/registration number only signifies th

Navigation menu