Geophysical Survey Systems 50200HS 200HS HyperStacking Antenna With HS Module 50200HS User Manual GSSI Antennas Manual

Download:
Mirror Download [FCC.gov]
Document ID	4156188
Application ID	f/uwti1negmQU99uNfouUw==
Document Description	User Manual updated
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.64kB (983013 bits)
Date Submitted	2019-01-31 00:00:00
Date Available	2019-02-04 00:00:00
Creation Date	2019-01-31 08:23:49
Producing Software	Microsoft® Word for Office 365
Document Lastmod	2019-01-31 08:23:49
Document Title	GSSI Antennas Manual
Document Creator	Microsoft® Word for Office 365
Document Author:	Kirsten Vargas

Copyright © 2009-2019 Geophysical Survey Systems, Inc.
All rights reserved
including the right of reproduction
in whole or in part in any form
Published by Geophysical Survey Systems, Inc.
40 Simon Street
Nashua, New Hampshire 03060-3075 USA
Printed in the United States
SIR, RADAN and UtilityScan are registered trademarks of Geophysical Survey Systems, Inc.
Geophysical Survey Systems, Inc.
Antenna Manuals
Limited Warranty, Limitations Of Liability And
Restrictions
Geophysical Survey Systems, Inc. hereinafter referred to as GSSI, warrants that for a period of
24 months from the delivery date to the original purchaser this product will be free from defects in
materials and workmanship. EXCEPT FOR THE FOREGOING LIMITED WARRANTY, GSSI
DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. GSSI's obligation is limited to
repairing or replacing parts or equipment which are returned to GSSI, transportation and insurance prepaid, without alteration or further damage, and which in GSSI's judgment, were defective or became
defective during normal use.
GSSI ASSUMES NO LIABILITY FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR INJURIES CAUSED BY PROPER OR IMPROPER OPERATION
OF ITS EQUIPMENT, WHETHER OR NOT DEFECTIVE.
Before returning any equipment to GSSI, a Return Material Authorization (RMA) number must be
obtained. Please call the GSSI Customer Service Manager who will assign an RMA number. Be sure to
have the serial number of the unit available
Regulatory Information
The use of GSSI antennas is governed by different regulatory agencies around the world. Specific
antenna models must be certified for legal operation in your country. Please read and understand the
following regulatory passages that pertain to your antenna. A listing of certified antennas by region can
be found www.geophysical.com/regulatoryinformation.htm.
Notice
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of the
device.
Survey Wheels
All of GSSI’s antennas are designed to operate with survey wheels. Some antennas have built-in survey
wheels, including the 62000 Palm Antenna and the Mini-SIR. The series of concrete antennas, including
the 5100, 5101 and 52600, have survey wheels built in to their special carts, the 614 and 615. The larger
antennas, including the 3101D, 5103, 50400 and 5104 are used in the larger carts, the 623 and 643, which
have survey wheels built in to them. Various sizes of survey wheels can also be attached directly to these
antennas. This includes the 611, 620 and 622. For highway surveys we use the 630 Distance measuring
Instrument (DMI).
Geophysical Survey Systems, Inc.
Antenna Manuals
Garantie limitée, limites de responsabilité et restrictions
Geophysical Survey Systems, Inc, ci-après dénommé GSSI, garantit à l'acheteur original de ce produit
que, pendant une période de 24 mois à compter de la date de livraison, ce dernier sera exempt de défauts
de matériaux et de fabrication. EXCEPTE POUR CETTE GARANTIE LIMITÉE, GSSI REJETTE
TOUTE GARANTIE, EXPLICITE OU IMPLICITE, Y COMPRIS TOUTE GARANTIE DE QUALITE
MARCHANDE OU D'ADEQUATION A UN USAGE PARTICULIER. L’obligation de GSSI est limitée
à la réparation ou le remplacement de pièces ou équipements qui sont retournés à GSSI, transport et
assurance prépayés, sans altération ni d'autres dommages, et qui, d’après GSSI, étaient défectueux ou sont
devenus défectueux lors d’une utilisation normale.
GSSI N'ASSUME AUCUNE RESPONSABILITE POUR LES DOMMAGES DIRECTS, INDIRECTS,
SPÉCIAUX, INCIDENTS OU CONSEQUENTS OU BLESSURES CAUSEES PAR UNE BONNE OU
MAUVAISE UTILISATION DE SON EQUIPEMENT DÉFECTUEUX OU NON.
Avant de retourner tout équipement à GSSI, une autorisation de retour matériel (RMA) doit être obtenue.
Appelez s'il vous plaît le service clientèle GSSI qui attribuera un numéro de RMA. Soyez sûr d'avoir le
numéro de série de l'unité.
Informations réglementaires
L'utilisation des antennes GSSI est régie par différents organismes de réglementation à travers le monde.
Certains modèles d'antenne spécifiques doivent être certifiés pour un fonctionnement légal dans votre
pays. Merci de lire et comprendre les passages suivants de réglementation qui s'appliquent à votre
antenne. Une liste des antennes certifiées par région peut être trouvée sur www.geophysical.com /
regulatoryinformation.htm.
Avis
La mise en œuvre est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer
d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent
causer un fonctionnement non désiré de l'appareil.
Roues codeuses – Odomètres
Toutes les antennes GSSI sont conçus pour fonctionner avec des roues codeuses. Certaines antennes,
comprenant l'antenne 62000 Palm et le Mini-SIR, intègrent directement les roues codeuses. La série
d'antennes pour le béton, comprenant les 5100, 5101 et 52600, ont des roues codeuses intégrées à leurs
chariots spéciaux, les 614 et 615. Les antennes plus grandes, telles que la 3101D, 5103, 50400 et 5104
sont utilisées dans les chariots plus grands, les 623 et 643, qui ont des roues codeuses intégrées.
Différentes tailles de roues codeuses peuvent être également être fixées directement sur ces antennes,
comprenant les 611, 620 et 622. Pour les auscultations de chaussées nous utilisons l’odomètre 630 (DMI :
Distance Measuring Instrument).
Geophysical Survey Systems, Inc.
Antenna Manuals
FCC Notice (for U.S. Customers):
This device complies with part 15, class F of the FCC Rules:
Operation is subject to the following conditions:
1. This device many not cause harmful interference, and
2. This device must accept any interference received, Including interference that may cause
undesired operation
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Operation of this device is restricted to law enforcement, fire and rescue officials, scientific research
institutes, commercial mining companies, construction companies and private parties operating on behalf
of these groups. Operation by any other party is a violation of 47 U.S.C. § 301 and could subject the
operator to serious legal penalties.
Coordination Requirements
(a) UWB imaging systems require coordination through the FCC before the equipment may be used. The
operator shall comply with any constraints on equipment usage resulting from this coordination.
(b) The users of UWB imaging devices shall supply detailed operational areas to the FCC Office of
Engineering and Technology who shall coordinate this information with the Federal Government through
the National Telecommunications and Information Administration. The information provided by the
UWB operator shall include the name, address and other pertinent contact information of the user, the
desired geographical area of operation, and the FCC ID number and other nomenclature of the UWB
device. This material shall be submitted to the following address:
Frequency Coordination Branch, OET
Federal Communications Commission
445 12th Street, SW
Washington, D.C. 20554
ATTN: UWB Coordination
(d) Users of authorized, coordinated UWB systems may transfer them to other qualified users and to
different locations upon coordination of change of ownership or location to the FCC and coordination
with existing authorized operations.
(e) The NTIA/FCC coordination report shall include any needed constraints that apply to day-to-day
operations. Such constraints could specify prohibited areas of operations or areas located near authorized
radio stations for which additional coordination is required before operation of the UWB equipment. If
additional local coordination is required, a local coordination contact will be provided.
Notice: Use of this device as a wall imaging system is prohibited by FCC regulations.
Geophysical Survey Systems, Inc.
Antenna Manuals
For U.S. Customers
Ground Penetrating Radar Coordination Notice And Equipment Registration
Note: This form is only for Domestic United States users. The Federal Communications Commission
(FCC) requires that all users of GPR who purchased antennas after July 15th, 2002 register their
equipment and areas of operation. It is required that you fill out this form and fax or mail to the FCC.
Failure to do this is a violation of Federal law.
1.
Date:
2.
Company name:
3.
Address:
4.
Contact Information [contact name and phone number]:
5.
Area Of Operation [state(s)]:
---Continued on next page.
Geophysical Survey Systems, Inc.
6.
Antenna Manuals
Equipment Identification:
Brand Name: Geophysical Survey Systems, Inc.
Antenna Model No. (center frequency): List all antennas being registered.
Model
7.
Frequency
FCC ID (QF7 followed by
Model #)
Receipt Date Of Equipment:
Fax this form to the FCC at: 202-418-1944
Or
Mail to:
Frequency Coordination Branch, OET
Federal Communications Commission
445 12th Street, SW
Washington, D.C. 20554
ATTN: UWB Coordination
Do not send this information to GSSI.
Geophysical Survey Systems, Inc.
Antenna Manuals
Canadian Requirements for RSS-220
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Geophysical Survey Systems, Inc.
Antenna Manuals
Canadian Requirements of RSS-220 for Ground
Antennas
This Ground Penetrating Radar Device shall be operated only when in contact with or within 1 m of the
ground.
This Ground Penetrating Radar Device shall be operated only by law enforcement agencies, scientific
research institutes, commercial mining companies, construction companies, and emergency rescue or
firefighting organizations.
Cet appareil de radar de sol (ou géoradar) ne doit être utilisé qu’en contact avec le sol ou à 1 m maximum
au dessus du sol.
Cet appareil de radar de sol ne doit être utilisé que par les forces de l’ordre, les instituts de recherche
scientifiques, les sociétés minières, les sociétés de construction, et les organisations de secours d’urgence
ou de combat du feu.
Geophysical Survey Systems, Inc.
Antenna Manuals
Declaration of CE Conformance
Geophysical Survey Systems, Inc. hereby confirms that the following named
products have been tested and meet the requirements of the European standards as indicated:
Models:
62000, 62300-XT, MINILT, MINIXT, LLTRx, 41000SA, 42000S, 50400S, 50270S,
D50300/800, 350HS, 50350US, 50200US
Description: Ground Penetrating Radar Antennas
European Standards: ETSI EN 301 489-32 V1.1.1 (2005-09), ETSI EN 301 489-1 V1.6.1
(2005-09), ETSI EN 301 489-1 V1.9.2 (2011-09), ETSI EN 302 066-1 V1.1.1(2005-09),
ETSI EN302 066-2 V1.1.1 (2005-09), ETSI EN 302 066-1 V1.2.1(2008-02), ETSI EN302
066-2 V1.2.1 (2008-02), ECC/DEC/(06)08
Place and Date of Issue: Intertek – ETL SEMCO 07.02.07, 03.11.09, 10.13.09, 11.18.09
Compliance Worldwide 03.23.12 09.25.12 04.14.14 10.12.15 11.10.15 11.13.15 09.30.16
12.20.16 05.09.18
Model:
Profiler™ EMP-400
Description: Electromagnetic Induction System
European Standards: EN61326:1997 + A1:1998 + A2:2001
Place and Date of Issue: Intertek – ETL SEMCO 08.29.06
Models:
SIR® 30, SIR® 30E
Description: Ground Penetrating Radar Data Acquisition System
European Standards: EN61000-6-4: 2007 per EN 55011:2009 + A1:2010
Place and Date of Issue: Compliance Worldwide 07.10.12, 07.11.12
Model:
SIR® 4000
Description: Ground Penetrating Radar Data Acquisition System
European Standards: EN61000-6-4: 2007 per EN 55011:2009 + A1:2010
Place and Date of Issue: Compliance Worldwide 04.14.14
Chris Plumlee
05.29.18
Name of authorized person
Geophysical Survey Systems, Inc.
270 MHz Antenna
Model 50270S
Table Of Contents
FCC Notice (for U.S. Customers)
Canadian Requirements for RSS-220
Declaration of CE Conformance
200 MHz Antenna ................................................................................................................... 5
200 MHz Antenna
50200HS HyperStacking Antenna
6
Geophysical Survey Systems, Inc.
1 GHz Horn Antenna
Model 41000SA
200 MHz Antenna
The 50200HS HyperStacking antenna has greatly improved resolution performance over previous GSSI
mid-frequency antennas, such as the Model 5106/A (200 MHz). The 50200HS can be used in continuous,
survey wheel or static stacking modes.
System Setup - Standard Settings
Shallow Profiling:
Range/Depth is approximately 7m assuming a dielectric constant of 9.
Setup Mode: Manual
System Run Mode: Survey Wheel (recommended) or Continuous
Range:150 ns
Number of Gain Points: 5
Vertical Low Pass Filter: 400 MHz
Vertical High Pass Filter: 30 MHz
Samples per Scan: 512
Bits per Sample: 16
Scans per Second: Set to the maximum scan rate allowed by the SIR System used.
Deep Profiling:
Range/Depth is approximately 15m assuming a dielectric
Setup Mode: Manual
System Run Mode: Survey Wheel (recommended) or Continuous
Range: 300 ns
Number of Gain Points: 5
Vertical Low Pass Filter: 400 MHz
Vertical High Pass Filter: 30 MHz
Samples per Scan: 1024
Bits per Sample: 16
Scans per Second: Set to the maximum scan rate allowed by the SIR System used.
MN30-903 Rev G
Geophysical Survey Systems, Inc.
1 GHz Horn Antenna
Model 41000SA
Signal Position
Place the antenna on the ground and use the Automatic Signal Position selection. The system will servo
and place the direct coupling pulse at the top of the time range window.
To test that you have the correct position, raise the antenna off the ground and you will observe on your
system that the antenna transmit pulse will separate from the reflection from the ground. The higher that
you raise the antenna, the further apart will be the two pulses.
To assure that the direct coupling pulse (time zero) is recorded the user should place the signal Position
servo in the manual mode. The signal should then be moved down in the time range window until the
entire surface pulse is visible and there is some ‘dead time’ or flat trace visible above the direct coupling
pulse in the time range window.
Gain Check
The surface pulse should be about 2/3 the width of the screen. If it is greater, reduce the Gains manually.
If the signal appears too small you can manually increase the Gains, but the first gain point should never
exceed 10dB, the last gain point should not exceed 65dB.
Specifications
Center frequency: 200 MHz
Pulse duration: 5 ns
Depth of penetration: 0-30 ft depending on dielectric permittivity
Size of sensor: 12x12x6.5 inches (60x60x30cm)
Weight of sensor: 39 lbs (17.72 kg)
MN30-903 Rev G

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 15
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word for Office 365
Title                           : GSSI Antennas Manual
Creator                         : Kirsten Vargas
Creator Tool                    : Microsoft® Word for Office 365
Create Date                     : 2019:01:31 08:23:49-05:00
Modify Date                     : 2019:01:31 08:23:49-05:00
Document ID                     : uuid:04BEB50E-B723-42BD-9DDA-E8B9DDE45CCF
Instance ID                     : uuid:04BEB50E-B723-42BD-9DDA-E8B9DDE45CCF
Author                          : Kirsten Vargas

EXIF Metadata provided by EXIF.tools