Getac Technology 015 CA27 Notebook Computer with Wireless LAN User Manual CA27 0
Getac Technology Corp. CA27 Notebook Computer with Wireless LAN CA27 0
Contents
- 1. Users Manual CA27
- 2. Users Manual LAN Card
Users Manual CA27
CA-27
Operation Manual
MITAC Technology Corporation
(April 2004)
TRADEMARKS
All brand and product names are trademarks or registered trademarks of their
respective companies.
NOTE
Information in this manual is subject to change without notice.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or peripheral devices) any changes or modifications
not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Regulations Information
Class B Regulations
USA
Federal Communications Commission Radio Frequency Interference Statement
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
? Reorient or relocate the receiving antenna.
? Increase the separation between the equipment and receiver.
? Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
? Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Please note:
The use of a non-shielded interface cable with this equipment is prohibited.
Canada
Canadian Department of Communications
Radio Interference Regulations Class B Compliance Notice
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
About the Battery
Caution Texts Concerning Lithium Batteries
DANISH
ADVARSEL!
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.
NORWEGIAN
ADVARSEL:
Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en
tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til
fabrikantens instruksjoner.
SWEDISH
VARNING:
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens
instruktion.
FINNISH
VAROITUS:
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan
suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
ENGLISH
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the equipment manufacturer. Discard used batteries
according to manufacturer's instructions.
DEUTSCH
VORSICHT:
Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben
oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter
Batterien nach Angaben des Herstellers.
FRENCH
ATTENTION:
II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer
uniquement avec une batterie du même type ou d’un type équivalent recommandé par le
constructeur. Mettre au rebut les batteries usagées conformément aux instructions du
fabricant.
Attention (for USA Users)
The product that you have purchased contains a rechargeable battery. The battery is
recyclable. At the end of its useful life, under various state and local laws, it may be illegal
to dispose of this battery into the municipal waste stream. Check with your local solid
waste officials for details in your area for recycling options or proper disposal.
About the Modem
Caution
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
5. Avoid using the telephone function during an electrical storm. There may be a remote
risk of electric shock from lightning.
6. Do not use the telephone function to report a gas leak in the vicinity of the leak.
Caution (for USA Users)
To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
i
Table of Contents
Preface .................................................................................................. v
Chapter 1 Getting Started............................................................1-1
Getting the Computer Running.............................................1-2
Unpacking.....................................................................1-2
Before You Begin .........................................................1-3
Connecting to AC Power...............................................1-4
Positioning the Tablet PC...............................................1-5
Using the Wireless Keyboard (option).............................1-6
Turning On and Off the Computer..................................1-7
Taking a Look at the Computer............................................1-9
Right-side Components ..................................................1-9
Left-side Components..................................................1-10
Rear Components........................................................1-11
Front Components .......................................................1-12
Bottom-side Components .............................................1-14
Where to Go from Here....................................................1-15
Chapter 2 Operating Your Tablet PC ........................................2-1
Starting and Stopping the Computer......................................2-2
Starting the Computer....................................................2-2
ii
Stopping the Computer...................................................2-2
Using the Wireless Keyboard (option)..................................2-4
Mouse-control Buttons...................................................2-4
Typewriter Keys ...........................................................2-5
Cursor-control Keys ......................................................2-5
Numeric Keypad...........................................................2-6
Euro Symbol.................................................................2-6
Windows Keys..............................................................2-7
Function Keys...............................................................2-7
Using the Touchscreen.......................................................2-8
Configuring the Touchscreen..........................................2-9
Using the Floppy Disk Drive (option) ................................. 2-10
Connecting the Floppy Disk Drive ................................ 2-10
Inserting and Ejecting Floppy Disks .............................. 2-12
Using the Hard Disk Drive................................................ 2-13
Using the CD/DVD Drive (option) .................................... 2-14
Connecting the CD/DVD Drive ................................... 2-14
Inserting and Removing a CD ...................................... 2-15
Using the Video Features.................................................. 2-17
Configuring the Display Modes..................................... 2-17
Using the Audio Features.................................................. 2-20
Connecting Audio Devices........................................... 2-21
Using the Communication Features.................................... 2-22
Using the Modem........................................................ 2-22
Chapter 3 Managing Power ........................................................3-1
AC and Car Adapter ..........................................................3-2
Battery Pack......................................................................3-3
Charging the Battery Pack.............................................3-3
Initializing the Battery Pack............................................3-4
Checking the Battery Level............................................3-4
Replacing the Secondary Battery Pack...........................3-5
iii
Battery Low Signals and Actions....................................3-6
Power Management............................................................3-8
Suspend-to-Disk (Suspend mode) ...................................3-8
Power-Saving Tips............................................................3-10
Chapter 4 Expanding Your Computer......................................4-1
Connecting a Serial Device..................................................4-2
Connecting a USB Device...................................................4-3
Connecting an IR Device ....................................................4-5
Using PC Cards..................................................................4-7
ZV and CardBus Support...............................................4-7
Inserting and Removing a PC Card.................................4-7
System Memory Upgrade....................................................4-9
Chapter 5 SCU (Setup Configuration Utility)..........................5-1
When and How to Use the SCU Program............................5-2
When to Use.................................................................5-2
Starting SCU.................................................................5-2
Moving Around and Making Selections ...........................5-4
Main Menu.........................................................................5-5
Advanced Menu.................................................................5-8
Security Menu..................................................................5-15
Power Menu ....................................................................5-18
Exit Menu ........................................................................5-22
Chapter 6 Installing Software Drivers.......................................6-1
How to Use the CD............................................................6-2
Installing Drivers for Windows 98........................................6-4
Touchscreen Driver.......................................................6-5
Installing Drivers for Windows 2000.....................................6-6
Touchscreen Driver.......................................................6-7
Installing Drivers/Utility for Windows NT 4.0.......................6-9
Touchscreen Driver.....................................................6-10
iv
Modem Driver ............................................................ 6-10
Other Drivers and Utilities................................................. 6-12
OVMAKFIL Utility..................................................... 6-12
Chapter 7 Caring for the Tablet PC...........................................7-1
Protecting the Computer .....................................................7-2
Using the Password.......................................................7-2
Using an Anti-Virus Strategy .........................................7-2
Taking Care of the Tablet PC..............................................7-3
Location Guidelines .......................................................7-3
General Guidelines.........................................................7-3
Cleaning Guidelines .......................................................7-4
Battery Pack Guidelines.................................................7-4
When Traveling..................................................................7-5
Chapter 8 Troubleshooting.........................................................8-1
Preliminary Checklist..........................................................8-2
Solving Common Problems..................................................8-3
Battery Problems ..........................................................8-4
CD/DVD Drive Problems..............................................8-4
Display Problems ..........................................................8-5
Floppy Disk Drive Problems...........................................8-7
Hardware Device Problems...........................................8-8
Hard Disk Drive Problems.............................................8-8
Infrared Problems .........................................................8-9
Keyboard and Mouse Problems......................................8-9
LAN Problems............................................................ 8-10
Modem Problems ........................................................ 8-10
PC Card Problems ...................................................... 8-11
Power Management Problems (for Windows)............... 8-11
Printer Problems ......................................................... 8-12
Software Problems...................................................... 8-12
Sound Problems .......................................................... 8-13
v
Startup Problems .........................................................8-13
Other Problems ...........................................................8-14
Resetting the Computer.....................................................8-15
Appendix A Specifications.......................................................... A-1
vi
Preface
This manual contains information that will help you operate the computer.
It is divided into 8 chapters and an appendix.
?? Chapter 1, Getting Started, takes you through the process of setting
up the computer and identifying its external components.
?? Chapter 2, Operating Your Computer, tells you how to use the
computer’s components and features.
?? Chapter 3, Managing Power, provides information on power.
?? Chapter 4, Expanding Your Computer, provides information on
installing and using peripheral devices.
?? Chapter 5, SCU (Setup Configuration Utility), describes the SCU
program that configures the computer’s BIOS settings.
?? Chapter 6, Installing Software Drivers, describes how to install the
drivers and utilities supplied with the computer.
?? Chapter 7, Caring for the Computer, gives you tips in care and
maintenance.
?? Chapter 8, Troubleshooting, gives solutions to common problems
you may encounter when using the computer.
?? Appendix A, Specifications, gives a brief specification of the
computer.
vii
Notational Conventions
Throughout this manual, the following conventions are used to distinguish
elements of text.
NOTE: identifies additional information that requires special attention.
CAUTION: identifies important information which, if not followed, may result in loss of data or
damage to the computer.
Keyboard keys are shown in a bold typeset. For example:
Press Enter to complete.
When keys are joined by a plus sign (+), press the first key, and, while
keeping the first key down, press the remaining keys, finally release all the
keys. When necessary, keys are also shown in graphics.
A title, command, setup item, or button that you can see on the screen is
shown in boldface. A value or an option that you can select for a setup
item is shown in italic. For example:
Select Power Management, set it to Enabled, and then click the
OK button.
CHAPTER
1
Getting Started
Congratulations on purchasing this Tablet PC.
This hand-held computer, having no fan and being almost noiseless, is
especially designed for the practical applications of warehouses,
automobiles, vehicles, public security, repairing, assisting the
handicapped, and other demanding situations where conventional
notebook computers just cannot measure up.
This chapter first tells you step by step how to get the computer up and
running. You will find instructions for these procedures:
?? Unpacking
?? Connecting to AC power
?? Turning on the computer
?? Turning off the computer
Then, you will find a section briefly introducing the external components
of the computer. And the last section navigates you to the information
you may need after the computer is ready for use.
1-2
Getting the Computer Running
This section guides you through the procedures for getting the computer
ready for operation.
Unpacking
After unpacking the shipping carton, you should find these standard
items:
?? Tablet PC
?? Accessories:
? AC adapter (100~240 VAC, 50~60 Hz)
? AC power cord (US, CE, UK, SA)
? Primary battery switch pin
? Driver CD
? X-Bay (optional):
Module-1: two serial I/O / RJ-45 / IEEE 1394
Module-2: wireless LAN (802.11B)
Module-3: wireless modem (CDPD)
? Expansion box (optional)
Port Replicator module: includes COM1/4, PIO1, CRT, two
USB ports (connects behind USB hub, FDD bootable), PS/2
keyboard and mouse, MIC input, earphone out, CD-ROM and
AC adapter input
CD-ROM module: 24X TEAC CD-224E or better
DVD-ROM module: 8X Pioneer K-11T or better
USB FDD module: 1.44 MB double-sided high density
? Wireless keyboard (optional)
? Car adapter/charger (10.7~32 VDC) ? (optional)
? Secondary battery (optional)
? Battery charger for secondary battery (optional)
? Carrying bag (optional)
? CCD camera module (optional)
? This Operation Manual
1-3
Inspect all the items. If any item is damaged or missing, notify your
dealer immediately.
Keep the shipping carton and packing materials in case you need to ship
or store the computer in the future.
Before You Begin
To prevent depletion of the primary battery’s power during transit, a
switch is provided at the bottom-side of the Tablet PC. Be sure to turn the
switch to the “ON” position when using the Tablet PC for the first time
by using the included primary battery switch pin to slide the switch.
NOTE: In case the Tablet PC will not be used for a long period of time and to prevent
primary battery discharge, turn the switch to the “OFF” position.
1-4
Connecting to AC Power
The computer operates either on the external AC power or internal
battery power. It is suggested that you use AC power when you start up
the computer for the first time.
CAUTION: Use only the AC adapter included with your computer. Using other AC
adapters may damage the computer.
NOTE:
Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated
minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates
with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P)
configuration; other end terminates with a molded-on appliance coupler.
Alternate: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated
minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord. One end terminates
with a Tandem blade, grounding, listed molded-on, attachments plug with a 6 A, 250 V
(NEMA 6-15P) configuration; other end terminates with a molded-on appliance
coupler.
1. Make sure the computer is turned off.
2. Plug the DC cord of the AC adapter to the power connector on the
right-side of the computer (?).
3. Plug the female end of the AC power cord to the AC adapter and the
male end to an electrical outlet (?).
1-5
4. When the AC adapter is connected, the indicator on the AC adapter
lights up, indicating that power is being supplied from the electrical
outlet to the AC adapter and onto your computer. Now, you are ready
to turn on the computer.
CAUTION:
?? When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the computer. A reverse procedure may damage the AC adapter or the
computer.
?? When unplugging the connector, always hold the plug head. Never pull on the cord.
NOTE: When the AC adapter is connected, it also charges the battery pack. For
information on using battery power, see Chapter 3.
Positioning the Tablet PC
The computer can be placed upright using its stand found at the back. To
place the computer in an upright position, pull open the stand located at
the back as shown on the next figure.
NOTE: It is recommended that you operate the Tablet PC in an upright position as
opposed to letting it lie flat on its back in order to provide adequate air ventilation.
The wireless keyboard operates on four “size-AA” (1.5-volt) batteries on
the battery compartment located at the back. Be sure to observe the
correct polarity when inserting the batteries.
NOTE: The condition of the batteries also affects the effectiveness of transmission. If a
weakness in transmission is detected, try changing a set of new batteries.
1-6
Using the Wireless Keyboard (option)
The wireless keyboard can either be placed flat on the table or inclined
using its stand found at the back. To place the wireless keyboard in an
upright position, pull open the stand located at the back as shown on the
next figure.
Place the wireless keyboard in front of the Tablet PC with no obstructions
between them to allow unhampered communication between the
computer and keyboard’s IR port.
NOTE: It is recommended that the transmission distance must not exceed 3 meters
and that vertical transmission angle is within ? 150 while horizontal transmission angle
is within ? 300.
1-7
Turning On and Off the Computer
Turning On
1. Make sure the computer is connected to AC power.
2. Press the power button .
3. Each time the computer is turned on, it performs a Power-On Self
Test (POST), and the operating system such as Windows should
start.
1-8
Turning Off
To turn off the computer power, use the “Shut Down” command of your
operating system.
NOTE: There are other ways you can stop the computer so that you will be back to
where you left off when you next turn on the computer. (See “Stopping the Computer”
in Chapter 2 for information.)
CAUTION: If you have to turn the computer on again immediately after turning it off,
wait for at least five seconds. Turning the computer off and on rapidly can damage it.
1-9
Taking a Look at the Computer
This section identifies the external components of the computer and
briefly describes the function of each component.
Right-Side Components
Ref
Component Description See Also
?
Reset Button Allows you to reset the system. P. 8-16
?
USB Port Connects a USB device, such as a USB floppy
drive, printer, digital camera, joystick, and more.
P. 4-7
?
Microphone
Connector Connects an external microphone. P. 2-20
1-10
Ref
Component Description See Also
?
Audio Output
Connector Connects a set of headphones, external speakers
with amplifier, or an audio recording device.
P. 2-20
?
Serial Port Connects a serial device, such as a mouse. P. 4-6
?
Expansion Port
For connecting to: Port Replicator,
CD/DVD-ROM module , or USB FDD module.
P. 2-14,
4-2, 4-4
?
Power
Connector
Connects the AC adapter. P. 1-3
?
PC Card Slot Accepts a PC Card for additional functions. P. 4-10
Left-Side Components
1-11
Ref
Component Description See Also
?
X-Bay Interface
Connects additional wireless LAN, wireless
modem (CDPD), external monitor, or 4 ports
(COM1/4, IEEE 1394, and LAN).
P. 4-2
?
IR Port Connects an IrDA-compliant device for wireless
data transfer.
P. 1-5,
4-8
?
RJ-11
Connector
Connects the telephone line. P. 2-21
Rear Components
Ref
Component Description See Also
?
Stand System’s vertical angle of inclination after the
stand is released 18 ± 3o.
P. 1-4
?
Secondary
Battery Pack
(option)
Supplies power to your computer when external
power is not connected.
NOTE: A BIOS keyboard switch is located
inside the secondary battery compartment, use
this to reset the system if the reset button on the
right-side of the Tablet PC is not effective (see
Right-Side Components).
P. 3-3
?
Touchscreen
Pen
Provides a convenient way to use the
touchscreen. Can be stretched for better grip and
handling.
P. 2-9
1-12
Front Components
Ref
Component Description See Also
?
LCD Panel and
Touchscreen Displays the output of the computer. Also serves
as your touchscreen.
P. 2-9
?
Power Button Turns the computer power ON and OFF. Also
serves as the SUSPEND/RESUME switch.
P. 1-6
?
Volume
Control/
Brightness
Control/
Battery
Capacity
Allows you to toggle between adjusting the
sound volume of the computer or brightness of
the LCD screen, or battery capacity.
P. 2-19
?
Device
Indicators
Shows the current status of the computer’s
devices.
Power ON indicator
Num Lock Indicator P. 2-5
Caps Lock Indicator P. 2-5
Scroll Lock Indicator P. 2-5
1-13
Ref
Component Description See Also
Shows the speaker volume, or the LCD
brightness level, or the primary/secondary
battery capacity
Suspend mode indicator (in reverse video)
Hard disk drive in-use indicator
Primary battery status indicator
Secondary battery status indicator
Volume adjust indicator
LCD brightness adjust indicator
?
Speaker
Volume/LCD
Brightness
Adjust Button
The upper button provides you a quick way to
increase while the lower button decreases the
sound volume of the computer or brightness of
the LCD screen.
P. 2-16,
2-19
?
IR Port Connects with a wireless keyboard (option) for
wireless data transfer.
P. 1-5,
4-8
?
Function Keys
1 , 2 ,
3
Each of the three buttons can be defined from F1
to F12 through the Setup utility.
P. 2-7,
5-15
?
Speaker Sends out sound and voice from the computer. P. 2-19
1-14
Bottom-Side Components
Ref
Component Description See Also
?
CCD USB Port
Connects a standard USB CCD PC camera. P. 4-7
?
Primary
Battery Switch Allows you to turn on/off power coming from
the internal primary battery.
NOTE: Be sure to turn the switch to the “ON”
position when using the Tablet PC for the first
time by using the included Primary Battery
Switch Pin to slide the switch.
P. 1-3
1-15
Where to Go from Here
As your computer is ready for operation, you may want to do any of the
following now:
For this purpose… Do this…
To know more about the computer… Go on to the next chapter.
To install the operating system if your
dealer has not already done so…
See the operating system manual.
To know more about the operating
system…
Read the operating system manual.
To install the drivers if your dealer has
not already done so…
See Chapter 6.
To set a power-on password… See “Security Menu” in Chapter 5.
To charge the battery pack for the first
time…
See “Charging the Battery Pack” in
Chapter 3.
CHAPTER 2
2
Operating Your Tablet PC
This chapter provides information about the use of the computer.
If you are new to computers, reading this chapter will help you learn
the operating basics. If you are already a computer user but are new to
Tablet PCs, you may choose to read only the parts containing
information unique to your computer.
Described in this chapter are the operating basics of these
components:
?? Wireless Keyboard
?? Touchscreen
?? Floppy disk drive
?? Hard disk drive
?? CD/DVD drive
And these features:
?? Starting and stopping the computer
?? Function keys
?? Video features
?? Audio features
?? Communication features
2-2
Starting and Stopping the Computer
There are a number of ways to start and stop the computer.
Starting the Computer
You always start the computer using the power button .
A computer starts up with an operating system (OS) existing on the
storage device such as the hard disk; or from a floppy disk or CD if you
have the respective modules installed. The computer will automatically
load the OS after you turn it on. This process is called booting.
NOTE: An operating system is the platform for all your software application
programs to run on. The most widely used operating system today is Microsoft
Windows.
Stopping the Computer
When you finish a working session, you can stop the computer by
turning off the power or leaving the computer in Standby or Suspend
mode:
To stop in
this mode…
Do this… To start up or
resume again
Off Follow the shutdown procedure of your
operating system. This can prevent loss of
unsaved data or damage to your software
programs.
If the system is locked up because of
hardware or software problems, press the
power button to turn off the computer.
Press the power
button .
Standby Depending on your settings in Windows,
you can put the computer in Standby
mode by pressing the power button
Press any key.
Suspend Depending on your settings in Windows,
you can put the computer in Suspend
mode by pressing the power button
Press the power
button .
2-3
mode by pressing the power button
If you choose to stop in Standby or Suspend mode, you can return to
where you left off the next time you start up the computer. (See
“Power Management” in Chapter 3 for more information.)
Using the Wireless Keyboard (option)
Before using the wireless keyboard, see section on “Positioning the
Tablet PC and Wireless Keyboard” on chapter 1. Your wireless
keyboard has all the standard functions of a full-sized computer
keyboard.
The standard functions of the keyboard can be further divided into five
major categories:
?? Mouse-control buttons
?? Typewriter keys
?? Cursor-control keys
?? Numeric keys
?? Function keys
Mouse-control Buttons
Mouse-control buttons found on both sides of the wireless keyboard
are similar to the buttons on a mouse. The left button (?) is similar to
the left- and right-click mouse function. The right button (?) allows
you to slide the on-screen pointer horizontally, vertically, or
diagonally.
2-4
Typewriter Keys
Typewriter keys are similar to the keys on a typewriter. Several keys
are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
The Control key is normally used in combination with other keys for
program-specific functions. The Alternate key is normally used in
combination with other keys for program-specific functions. The
Escape key is usually used for stopping a process. Examples are
exiting a program and canceling a command. The function depends on
the program you are using. When the lock keys (Caps Lock, Num
Lock, and Scroll Lock) are pressed, their corresponding indicators
light up on the Tablet PC front panel’s device indicators.
Cursor-Control Keys
?
?
2-5
NOTE: The word “cursor” refers to the indicator on the screen that lets you know
exactly where on your screen anything you type will appear. It can take the form of
a vertical or horizontal line, a block, or one of many other shapes.
Numeric Keypad
A 15-key numeric keypad is embedded in the typewriter keys as
shown next:
Numeric keys facilitate entering of numbers and calculations. When
Num Lock is on, the numeric keys are activated; meaning you can use
these keys to enter numerals.
NOTE:
?? When the numeric keypad is activated and you need to type the English letter in
the keypad area, you can turn Num Lock off.
?? Some software may not be able to use the numeric keypad on the external
wireless keyboard.
Euro Symbol
If your Windows supports the Euro dollar sign , you can press the
sign on the keyboard.
2-6
?? To press the Euro sign on the keyboard, hold down either of the Alt
keys and type 0128 on the numeric keypad of your keyboard.
?? To press the Euro sign on an UK keyboard, hold down the Alt Gr
key and press 4 (which has an Euro sign on it).
Windows Keys
The keyboard has two keys that perform Windows-specific functions:
? Windows Logo key and Application key.
The ? Windows Logo key opens the Start menu and performs
software-specific functions when used in combination with other
keys.
The Application key usually has the same effect as a right mouse
click. (See your Windows manual for more information.)
Function Keys
On the top row of the keys are the function keys: F1 to F12. Function
keys are multi-purpose keys that perform functions defined by
individual programs.
2-7
Using the Touchscreen
CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the
touchscreen. Doing so may damage the touchscreen surface. Use the included
touchscreen pen instead, which can be stretched for better grip and handling.
The touchscreen is a touch-sensitive device that allows you to
communicate with the computer by controlling the location of the pointer
on the screen and making selection with the buttons.
The touchscreen needs a special device driver support called a PenMount
Utility, which allows you to easily use the Tablet PC without any
external pointing device.
The touchscreen pen is located at the rear of the Tablet PC (refer to “Rear
Components” on chapter 1). You might need to tilt the Tablet PC after
opening the touchscreen pen holder to get it. To use the touchscreen,
place the touchscreen pen or your forefinger on the touchscreen. As you
slide your pen or fingertip across the screen, the pointer, or cursor, on the
screen moves in the same direction across the screen as your fingertip or
pen moves across the screen.
Here are some common terms that you should know when using the
touchscreen:
Touchscreen Pen
Holder
2-8
Term Action
Point Move your finger or pen on the touchscreen until the
cursor points to the selection on the screen.
Click Tap gently anywhere on the touchscreen.
Double-click Tap twice on the touchscreen rapidly.
Drag and
drop
Press lightly on the touchscreen and move your finger or
pen until you reach your destination (drag). Finally,
release your finger or pen (drop) when you finish dragging
your selection to the destination. The object will drop into
the new location.
Scroll To scroll is to move up and down or left and right in the
working area on the screen.
To move vertically, place your finger or pen on the right
edge of the touchscreen and slide your finger or pen up and
down along the edge. To move horizontally, place your
finger or pen on the bottom edge of the touchscreen and
slide your finger or pen left and right.
This function works only after you install the touchscreen
driver supplied with the computer and it may not work for
all applications.
TABLE NOTE: If you swap the left and right buttons, “tapping” on the
touchscreen as an alternative method of pressing the left mouse button will
no longer be valid.
Configuring the Touchscreen
You may want to configure the touchscreen to suit your needs. For
example, if you are a left-handed user, you can swap the two buttons
function of the left mouse-control button on the wireless keyboard so
that you can use the right mouse button as the left mouse button and
vise versa. You can also change the size of the on-screen pointer, the
speed of the pointer, and so on.
To configure the touchscreen, you can use the standard Microsoft or
IBM PS/2 driver if you are using Windows. However, you can install
2-9
the touchscreen driver supplied with your computer to take advantage
of more powerful features. (For information on installing the driver,
see Chapter 6.)
Using the Floppy Disk Drive (option)
Your Tablet PC comes with an USB floppy disk drive as drive A
through the USB port on the right side, or port replicator on an
optional expansion box, or through the USB port located on the plug
of an optional CD-ROM drive module.
A floppy disk drive allows you to install new programs into your
computer, or to store information on a removable floppy disk so you
can transfer information from one computer to another.
The floppy disk drive is a high-density 3.5-inch one, which can read
and write to either double-density (2DD) 720-KB floppy disks or
high-density (2HD) 1.44-MB floppy disks. Notice that both types of
floppy disk have an arrow imprinted on the front upper left corner, and
a sliding write-protect tab on the bottom left corner, as illustrated
above. When opened, the write-protect tab prevents data from being
written to, or erased from the floppy disk.
Connecting the Floppy Disk Drive
Connect the floppy disk drive through any of the following methods:
?? Through the Tablet PC’s USB Port –
Insert the USB plug of floppy disk drive into the USB port located
on the right side of the Tablet PC.
?? Through the Expansion Port Plug of the CD-ROM Drive
Module –
Insert the USB plug of floppy disk drive into the USB port located
on the expansion port plug of the CD-ROM drive module.
2-11
Inserting and Ejecting Floppy Disks
To insert a floppy disk, hold it with the arrow facing up and towards
the drive. Slide the disk into the drive until it clicks into place.
To eject a floppy disk, first ensure that the floppy disk drive in-use
indicator is off, and then press the eject button on the drive. When the
floppy disk pops out of the drive, remove the floppy disk and store it
properly.
2-12
CAUTION:
?? Never turn off or reset the computer while the floppy disk drive in-use indicator is
on.
?? Always store your floppy disks in a safe, clean container, to protect them from
the environment and magnetic fields.
?? A floppy disk must be formatted before you can use it. (To know how to format a
floppy disk, see your operating system manual.)
2-13
Using the Hard Disk Drive
Your computer comes with a hard disk drive as drive C.
A hard disk drive is a storage device with non-removable, rotating,
magnetic storage platters inside it. It is where your operating system
and application software programs are stored.
Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics)
hard disk drive. This type of drive embodies the latest in fast, reliable
mass storage by integrating all the control circuitry necessary for
operation directly onto the drive itself. This allows the drive
manufacturer to carefully optimize drive performance.
CAUTION:
?? Make regular backups of your data files from your hard disk drive to floppy disks
or other storage media.
?? Never try to remove or install the hard disk drive while the computer is powered
on. Doing so can result in loss of data, and can damage the computer and the
hard disk drive’s sensitive circuitry.
?? Never turn off or reset the computer while the hard disk drive in-use indicator is
on.
2-14
Using the CD/DVD Drive (option)
Depending on the model, your computer comes with a CD-ROM drive
or DVD-ROM drive module. This drive is usually configured as drive
D and is connected to the expansion port located on the right side of the
Tablet PC.
The drive uses removable 5.25-inch silver CD-ROM discs, which look
like standard music CDs. It is an ideal medium to use for distributing
multimedia because of the huge amount of data that a disc can store.
A CD-ROM drive can read CD-ROMs, audio CDs, and CD-R disk. A
DVD-ROM drive can read DVD (Digital Versatile Disc) discs in
addition to the above discs.
NOTE: If the DVD-ROM drive would be operating for more than half an hour (such
as showing a DVD title), use the AC or car power source instead of the battery. If
not, the battery may run out of power before the operation is complete.
CAUTION:
1. When inserting a CD, do not use force.
2. Make sure the CD is correctly inserted into the tray, and then close the tray.
3. Do not leave the CD tray open. Also, avoid touching the lens in the tray with your
hand. If the lens becomes dirty, the CD-ROM may malfunction.
4. Do not wipe the lens using materials with rough surface (such as paper towel).
Instead, use a cotton swab to gently wipe the lens.
FDA regulations require the following statement for all laser-based devices:
“Caution, Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.”
2-15
Connecting the CD/DVD Drive
Insert the expansion plug of CD/DVD drive into the expansion port
located on the right side of the Tablet PC.
Inserting and Removing a CD
Follow this procedure to insert or remove a CD.
1. Turn on the computer.
2. Press the eject button and the CD tray will slide out partially.
Gently pull on it until it is fully extended.
3. To insert a CD, place down the CD in the tray with its label facing
up. Slightly press the center of the CD until it clicks into place.
2-16
To remove a CD, hold the CD by its outer edge and lift it up from the
tray.
4. Gently push the tray back into the drive.
NOTE: In the unlikely event that you are unable to release the CD tray by pressing
the eject button, you can manually release the CD. (See “CD/DVD Drive Problems”
in Chapter 8.)
2-17
Using the Video Features
The video subsystem of your computer features:
?? 10.4-inch TFT (Thin-Film Transistor) 18-bit color LCD display
with 1024x768 XVGA (Extended Video Graphics Array)
resolution.
?? Simultaneous display on LCD and external monitor, which is
useful when you have a presentation as you can control the screen
from your computer and face the audience at the same time.
?? Multi-display capability, which allows you to expand your desktop
on the screen to another display device so that you have more
desktop space to work on.
?? Power Management.
Configuring the Display Modes
NOTE: To take advantage of the enhanced video capabilities, the video driver
supplied with your computer must be installed.
Your computer has been set to a default resolution and number of
colors before shipment. You can view and change display settings
through your operating system. See your operating system
documentation or online help for specific information.
For displaying in higher resolutions, you can connect an external CRT
monitor that supports higher resolutions through an optional Port
Replicator Module.
The following table lists the display modes supported by your
computer.
2-18
Display Mode
LCD Only
CRT Only
Simultaneous
Display
Resolution
Colors
8-bit ? ? ?
16-bit ? ? ?
24-bit ? ? ?
640x480
32-bit ? ? ?
8-bit ? ? ?
16-bit ? ? ?
24-bit ? ? ?
720x480
32-bit ? ? ?
8-bit ? ? ?
16-bit ? ? ?
24-bit ? ? ?
800x600
32-bit ? ? ?
8-bit ? ? ?
16-bit ? ? ?
24-bit ? ? ?
848x480
32-bit ? ? ?
8-bit ? ? ?
16-bit ? ? ?
24-bit ? ? ?
1024x768
32-bit ? ? ?
8-bit ?
16-bit ?
24-bit ?
1152x864
32-bit ?
2-19
Display Mode
LCD Only
CRT Only
Simultaneous
Display
8-bit ?
16-bit ?
1280x1024
24-bit ?
8-bit ? 1600x1200
16-bit ?
TABLE NOTE: 8-bit = 256 colors; 16-bit = High Color or 65,536 (64 K)
colors; 24 and 32-bit = True Color 16,770,000 (16 M) colors.
2-20
Using the Audio Features
NOTE:
?? To take advantage of the enhanced audio capabilities, the audio driver supplied
with your computer must be installed.
?? If you experience interference while recording, try lowering the microphone
recording volume.
The audio subsystem of your computer features:
?? Digital audio and analog mixing functions required for recording
and playing sound on your computer
?? SoundBlaster Pro, Adlib, and Microsoft Windows Sound System
support
?? Volume control select (?)
?? Volume adjust (increase or decrease) (?)
?? Speaker (?)
?? External audio connectors (?)
2-21
Ways of playing and recording sound vary with the operating system
used. See your operating system documentation or online help for
specific information.
Connecting Audio Devices
For higher audio quality, you can send or receive sound through
external audio devices.
?? Microphone Connector ( ) can be connected to an external
microphone for recording voice or sound.
?? Audio Output Connector ( ) can be connected to the line-in
connector of powered speakers with built-in amplifiers,
headphones, or earphone set. This connector is compliant with
S/PDIF (Sony/Philips Digital Interface). You can connect audio
equipment with S/PDIF to the computer.
2-22
Using the Communication Features
Using the Modem
NOTE: To take advantage of the modem feature, the modem driver supplied with
your computer must be installed.
The internal 56 K fax/data modem allows you to use the telephone line
to communicate with others by fax, email, or connect to an online
service or bulletin board.
To connect the telephone line to the modem, connect the end nearest
the core on the modem cable to the computer’s RJ-11 connector and
the other end to the telephone line.
NOTE:
?? When using communication software, you may have to disable power
management.
?? Set the COM port of the modem to COM2.
?? Set parameters such as modem speed (baud rate) and line type (pulse dialing or
tone dialing).
?? Do not enter Standby mode when using communication software.
2-23
Using the Wireless LAN (WLAN)
An internal Mini PCI wireless LAN (Intel Centrino platform) module
have been pre-installed by your computer manufacturer at the factory.
This allows you to access corporate networks or the Internet in a
wireless environment.
To take advantage of the WLAN feature, make sure that the WLAN
driver is installed correctly. If your WLAN module was provided by
your dealer instead of the computer manufacturer, contact your dealer
for the correct driver to use.
Configuring the WLAN
After driver installation, you can use the WLAN utility to configure
and monitor your WLAN connection. If you are using Windows XP,
you can also use its built-in WLAN utility. Follow this procedure to
launch the WLAN utility in Windows XP:
1. Select Control Panel from the Start menu.
2. Click Network and Internet Connections.
3. Click Network Connections , then double-click the Wireless
Network Connection icon .
4. Click Properties in the Wireless Network Connection Status
dialog box.
5. You can configure your WLAN settings in the Wireless Network
Connection Properties dialog box.
2-24
Turning Off/On the WLAN Radio
NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate
wireless devices in aircraft as this may interfere with flight safety. Remember to
select turn off wireless LAN when using your computer in the airplane.
Your computer has a built-in Fn+F11 hot key to switch the WLAN
radio on/off (see “Hot Keys” in chapter 2).
Both Windows XP WLAN utility and the Fn+F11 hot key must be on
for the WLAN function to work. The WLAN indicator ( ) glows to
indicate that the computer is ready for WLAN connection.
To turn off the WLAN function, either press Fn+F11 or turn off the
WLAN utility.
It takes approximately 30 seconds for your computer to make a
successful WLAN connection and approximately 10 seconds to
disconnect.
CHAPTER
3
Managing Power
Your computer operates either on external AC power, car adapter, or
internal battery power.
This chapter tells you how you can effectively manage power. To
maintain optimal battery performance, it is important that you use the
battery in the proper way.
The topics in this chapter include:
?? What is an AC or car adapter
?? How to charge the battery pack
?? When and how to initialize the battery pack
?? How to check the battery level
?? How to replace the battery pack
?? What happens when the battery is low and what actions to take
?? What is Power Management
?? How to save power
3-2
AC and Car Adapter
CAUTION:
?? The AC and car adapter is designed for use with your computer only. Connecting
the AC adapter to another device can damage the adapter.
?? The AC power cord supplied with your computer is for use in the country where you
purchased your computer. If you plan to go overseas with the computer, consult
your dealer for the appropriate power cord.
?? When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the computer. A reverse procedure may damage the AC adapter or
computer.
?? When unplugging the connector, always hold the plug head. Never pull on the cord.
The AC adapter serves as a converter from AC (Alternating Current) to
DC (Direct Current) power because your computer runs on DC power,
but an electrical outlet usually provides AC power. It also charges the
battery pack when connected to AC power. The AC adapter operates on
any voltage in the range of 100 ~ 240 V AC.
The car adapter serves as a converter from car battery to DC power. The
cigarette lighter port of the car usually provides DC power. It also charges
the battery pack when connected. The car adapter operates on any voltage
in the range of 10.7 ~ 32 V DC.
NOTE: The battery pack cannot be charged when the input power of car adapter falls
below 11.5 V DC.
3-3
Battery Pack
The battery pack is the internal power source for the computer. It is
rechargeable using the AC or car adapter.
The operating time of a fully charged battery pack depends on how you
are using the computer. When your applications often access peripherals,
you will experience a shorter operating time.
NOTE: Located on the bottom-side of the Tablet PC is the CCD USB port that contains
a switch for turning off power coming from the internal primary battery. (Refer to
“Bottom-side Components” on chapter 1 for the actual location.)
CAUTION: Care and maintenance information for the battery is provided in Chapter 8.
In addition to this chapter, be sure to read the “Battery Pack Guidelines” section in
Chapter 8 as well.
Charging the Battery Pack
NOTE:
?? Charging will not start if the battery’s temperature is below 0?C (32?F) or above
40?C (104?F).
?? The charging process will stop when the battery’s temperature gets above 60?C
(140?F). If this happens, the battery pack may be damaged, please contact your
dealer.
?? During charging, do not disconnect the AC adapter before the battery has been fully
charged; otherwise you will get a prematurely charged battery.
To charge the battery pack, connect the AC adapter to the computer and
an electrical outlet. The Battery Charge Indicator ( or ) on the
Tablet PC’s Device Indicators appears to indicate that charging is in
progress. You are advised to keep the computer power off while the
battery is being charged. When the battery is fully charged, the Battery
Charge Indicator disappears.
It takes approximately 90 minutes to charge the battery pack to 80%
capacity and two or three more hours to fully charge the battery pack.
CAUTION: After the computer has been fully recharged, do not immediately disconnect
and reconnect the AC adapter to charge it again. Doing so may damage the battery.
3-4
Initializing the Battery Pack
You need to initialize a new battery pack before using it for the first time
or when the actual operating time of a battery pack is much less than
expected.
Initializing is the process of fully charging, discharging, and then
charging. It can take several hours.
1. Make sure the computer power is turned off. Connect the AC adapter
to fully charge the battery pack.
2. After the battery pack is fully charged, turn on the computer.
3. Disconnect the AC adapter and leave the computer on until the
battery is fully discharged. The computer will shut down
automatically.
4. Connect the AC adapter to fully charge the battery pack.
Checking the Battery Level
When two batteries exist on the system, the battery’s discharge sequence
is from the secondary battery to the primary battery. When the battery
charge on the secondary battery falls below 5%, then power usage will
switch to the primary battery. When the battery charge on the primary
battery falls below 5%, then system will shutdown.
NOTE: Any battery level indication is an estimated result. The actual operating time can
be different from the estimated time, depending on how you are using the computer.
By Operating System
You can check the approximate battery level using the battery meter
function of the operating system. To read the battery level in Windows,
click the icon on the taskbar. (Click the icon if the computer is
using AC power.)
3-5
By Gas Gauge
The internal primary battery pack does not support the gas gauge display
on the battery itself, but on the exterior side of the secondary battery pack
(option) is a gas gauge for displaying the estimated battery charge. When
the secondary battery pack is not installed in the Tablet PC and you want
to know the battery charge, you can press the on/off switch with a pointed
device to see the corresponding value of indicator segment that light
green. The value of the corresponding green segment indicates the
relative percentage of the battery charge. The battery pack is fully
discharged when you see no segment glowing green.
Replacing the Secondary Battery Pack
CAUTION:
?? There is danger of explosion if the battery is incorrectly replaced. Replace the
battery only with the computer manufacturer’s optional battery packs. Discard used
batteries according to the dealer’s instructions.
?? Do not attempt to disassemble the battery pack.
If you often rely on battery power for a long period of time while
traveling, you may consider the purchase of an additional secondary
battery pack from your dealer and keep it with you in a fully charged state
as a backup.
To replace the battery pack, follow these steps:
1. Make sure the computer is not turned on or connected to AC power.
However, the Tablet PC supports the battery hot-swap function,
providing you the ability to replace the battery even during system
on.
2. Carefully place the computer upside down.
3. Open the stand fully (?).
On/Off
Switch
Device Indicator
Segment
3-6
4. Slide the release lever (?) to the right and pull the battery pack out of
its compartment (?) by using your thumb and index finger.
5. Insert the new battery pack into the compartment and slide the release
lever first to the right to accommodate it, then releasing it to the lock
position.
Battery Low Signals and Actions
Battery Low occurs when the battery has approximately 10% of its
charge remaining. The computer gives warning beeps and the Battery
Charge Indicator ( or ) blinks to alert you to take actions.
NOTE: You can set up your threshold and signals of Battery Low under Windows.
Immediately save your data upon Battery Low. The remaining operating
time depends on how you are using the computer. If you are using the
audio subsystem, PC Card, hard or floppy disk drives, the battery might
run out of charge very quickly.
Always respond to Battery Low by placing your computer on
suspend-to-disk, turning off the computer, or connecting the AC or car
adapter.
3-7
If you do not take any action and after two minutes’ of warning beeps, the
computer will automatically suspend-to-disk and turn off.
CAUTION:
?? If the “Battery Low Warning Beep” item is disabled in the Setup Configuration Utility
(SCU) program, the computer will not beep.
?? If you are using a flash PC Card, do not access the card during battery low periods.
This is because the access may take longer than the time it takes the battery to run
out of charge, thus making your access to the card unsuccessful.
?? If you fail to save your data when the battery completely runs out of charge, then
you lose your data.
3-8
Power Management
Your computer supports APM (Advanced Power Management) and
ACPI (Advanced Configuration and Power Interface) for power
management. The power management feature allows you to reduce the
power consumption for energy saving.
With an ACPI-compliant operating system such as Windows 98 and
Windows 2000, power supply to different computer components is
controlled on an as-needed basis. This allows maximum power
conservation and performance at the same time.
In general, Windows’ power management works in this way:
What… When…
Power to the hard disk is turned off When the hard disk has been idle for a
set period.
Power to the display is turned off When the display has been idle for a
set period.
The computer enters Standby mode.
The hard disk and display are turned
off and the entire system consumes
less power.
When the entire system has been idle
for a set period.
The computer enters Suspend mode.
(See the next subsection for more
information.)
When you press the power button .
*
* depends on your settings in Windows.
For detailed information on power management, see Windows’ Help.
Suspend-to-Disk (Suspend mode)
NOTE: If your operating system does not support ACPI, you can use the computer’s
“Suspend-to-Disk” function, which is equivalent to Windows’ Hibernation function. (See
“Power Menu” in Chapter 5 for more information.)
3-9
Manual Power Management
You can manually initiate Suspend-to-disk mode at any time in one of
two ways:
?? Use the O/S that supports the Suspend function.
?? Press down the power button and release it in less than 4 seconds
with the system on. Repeat the action to wake up the system under
Suspend mode.
NOTE:
1. The suspend-to-disk partition may not exist on your hard disk. Check with your
dealer to know if it exists. If there is no suspend-to-disk partition, you cannot use
the Suspend-to-disk feature.
2. The OVMAKFIL utility allows you to create the suspend-to-disk partition. (Refer to
section on “OVMAKFIL Utility” for information.)
Suspend-to-disk is a very useful feature. People frequently open many
applications when they use computers. It takes some time to get all these
applications open and running, and normally they all have to be closed
before the system can be turned off.
When you use the Suspend-to-disk feature, you do not have to close the
applications. The computer stores the state of your computer to a file on
the hard disk and then shut down. The next time you turn on your
computer, you return to exactly where you left off.
3-10
Power-Saving Tips
In addition to your computer’s automatic power management, you can do
your part to maximize the battery’s operating time by following these
suggestions.
?? Do not disable Power Management.
?? Decrease the LCD brightness to the lowest comfortable level.
?? Disable the parallel and serial ports if no devices are connected to
these ports. (See “Advanced Menu” in Chapter 5.)
?? If you work with an application that uses the serial port or a PC Card,
exit the application when you finish using it.
?? If you have a PC Card installed, remove it when not in use. Some PC
Cards drain power even while they are inactive.
?? Turn off the computer when you are not using it.
CHAPTER
4
Expanding Your Computer
You can expand the capabilities of your computer by connecting other
peripheral devices. When using a device, be sure to read the instructions
accompanying the device together with the relevant section in this
chapter.
This chapter gives guidelines on installing and using these devices:
?? Serial device
?? IR device
?? USB device
?? PC Card
4-2
Connecting a Serial Device
Your computer has a serial port for connecting a serial device such as a
serial mouse or modem.
Follow this procedure to connect a serial device:
1. Make sure the “COM1 Port” item is set properly in the SCU program.
(See “Advanced Menu” in Chapter 5 for information.)
2. Make sure the computer is not turned on.
3. Plug the device cable to the serial port on the right side of the Tablet
PC.
4. Turn on the computer.
NOTE: Portable modems that derive power through the serial port cannot be used with
the Tablet PC. Instead, use a modem that is powered by its own internal battery or
external AC power.
4-3
Connecting a USB Device
Your computer has one USB port on the right side for connecting USB
devices such as digital camera, scanner, printer, modem, or mouse; and
one CCD USB port at the bottom-side for connecting an optional CCD
camera.
NOTE: You can also use the USB port located on the Expansion Port plug of the
optional CD-ROM drive module.
USB is specified to be an industry standard extension to the PC
architecture. It supports “Plug and Play” technology so you can install
and remove USB devices without turning off the computer. With its
multiple connection capability, up to 127 devices can be connected in a
daisy-chain configuration. In addition, you can use a USB hub that
converts a single USB connector into multiple ports where USB devices
can be connected.
To connect a standard USB device, simply plug the device cable to the
USB port on the right side of the Tablet PC, or through the optional
CD-ROM drive module’s Expansion Port plug.
To connect an optional CCD camera, simply place the camera on top of
the Tablet PC nearest the CCD USB port. Align and plug in the golden
finger connector to the CCD USB port at the bottom-side of the Tablet PC
and secure it in place with the built-in screw. Adjust the angle of the CCD
camera according to your need.
4-4
4-5
Connecting an IR Device
Your computer has an IR (infrared) port for connecting an infrared-
equipped device wirelessly such as a wireless keyboard/mouse, another
computer, printer, or PDA (Personal Digital Assistant).
The infrared feature supports these standards:
For the front panel’s IR port
?? IR keyboard/mouse that supports Forward FK34PUS002 (US
language) specification
For the left side’s IR port
?? IrDA 1.1 (FIR – Fast Infrared) with 9.6 Kbps to 4.0 Mbps transfer
rate
?? HPSIR – Serial Infrared mode
Follow this procedure to connect an IR device:
1. Under Windows, make sure that the IrDA Fast Infrared Port is set to
HP HSDL-2300/3600. (See “How to Use the CD” in Chapter 6 for
information.)
2. Make sure that the “COM2 Port” and its “Mode” items are set
properly in the SCU program. (See “Advanced Menu” in Chapter 5
for information.)
3. When using the front panel’s IR port:
Place the wireless keyboard where its IR port faces the IR port of
your computer within the effective range ? within ?15-degrees
vertical angle and within ?30-degrees horizontal angle at no greater
than 3 meter distance.
4-6
When using the left side’s IR port:
Place the transmitting device where its IR port faces the IR port of
your computer within the effective range ? within ?20-degrees
vertical angle and within ?20-degrees horizontal angle at no greater
than 0.8~1.0 meter distance.
Place the receiving device where the IR port of the Tablet PC faces its
IR port within the effective range ? within ?15-degrees vertical angle
and within ?15-degrees horizontal angle at no greater than 0.8~1.0
meter distance.
4. To take advantage of the IR communications, you need a third party
software.
NOTE: During infrared communication, take note of the following:
?? Do not move the computer and IR device.
?? Do not enter Standby mode.
?? Do not use a cell phone or another IR device near the computer.
?? Avoid strong light such as sunlight or fluorescent light.
?? Disable the screen saver.
4-7
Using PC Cards
Your computer has one PC Card slot to accommodate one type II card.
ZV Port and CardBus Support
Your computer’s PC Card slot supports CardBus and ZV
(Zoomed-Video) Port specifications. CardBus is the 32-bit version of PC
Card technology. It allows speeds of up to 133 Mbps at 33 MHz. Typical
applications are SCSI host bus, graphic video, and high-speed network
cards.
Inserting and Removing a PC Card
NOTE:
?? Some PC Cards require additional system resources. Before using such PC card,
you may have to free other system resources for the PC Card.
?? Although some PC Cards can be inserted and removed without turning off the
computer, you cannot remove or install PC Cards during Standby mode.
To insert a PC Card:
1. Locate the PC Card slot on the right side of the computer.
2. Slide the PC Card, with its label facing up, into the slot until the eject
button pops out.
4-8
3. When a new card is seated, the computer will detect it and try to
install the appropriate driver. Follow the on-screen instruction to
complete the process.
To remove a PC Card:
1. Your operating system may require you to stop the PC Card before
you actually remove it. (In Windows, double-click the PC Card icon
in Control Panel to stop the card.)
2. Push the eject button and the card will slide out slightly.
3. Pull the card out of the slot.
4-9
System Memory Upgrade
You can upgrade your computer by changing system memory to a
maximum of 256 MB on the SO-DIMM slot. However, to avoid damage
during the installation procedure, please ask your dealer for help.
CHAPTER
5
Setup Configuration Utility (SCU)
SCU is a program for configuring the BIOS (Base Input/Output System)
settings of the computer.
BIOS is a layer of software, called firmware, that translates instructions
from other layers of software into instructions that the computer hardware
can understand. The BIOS settings are needed by your computer to
identify the types of installed devices and establish special features.
This chapter tells you how to use the SCU program.
5-2
When and How to Use the SCU Program
When to Use
You need to run the SCU program when:
?? You see an error message on the screen requesting you to run Setup.
?? You want to restore the factory default settings.
?? You want to modify some specific settings according to the
hardware.
?? You want to modify some specific settings to optimize system
performance.
Starting SCU
NOTE:
?? The Setup screens shown in this chapter are for your reference only. The actual
items or settings on your computer may differ.
?? The Setup program may have been updated after the publication of this manual.
?? The settings you select in your operating system might override similar settings in
Setup.
To run SCU, press F2 when the prompt appears in the lower left corner of
the screen during system startup. The prompt shows up on the screen for
only a few seconds. You must press F2 quickly. The SCU menu appears
as shown next.
5-3
The menu can be divided into four areas:
?? On the top line is the menu bar containing the titles of the available
menus. Each menu title brings a specific menu.
?? The center left column of the menu contains items that you can set for
the selected menu title. The arrow sign in front of an item indicates
there is a sub-menu for the item.
?? The right column of the menu provides help information of the
selected item.
?? The bottom lines give keyboard instructions for moving around and
making selections.
5-4
Moving Around and Making Selections
A brief description of keyboard (if installed) usage is listed next:
Key Function
?, ? Selects a menu title.
?, ? Selects an item or option.
Enter 1) Brings up the sub-menu when an item with the arrow sign is
selected.
2) Opens or closes the options window when an item is selected.
Space bar,
–
Cycles through the pre-defined value for the selected item.
Pressing the space bar brings up the next value; pressing the
minus (–) key does the contrary.
Esc 1) Exits the SCU program.
2) Returns to the previous menu if in a sub-menu.
3) Closes the options window if one is open.
NOTE: You are advised to use the mouse (if installed) as it is more straightforward than
using the keyboard.
5-5
Main Menu
The Main menu contains the basic configuration settings of the system.
Date and Time
Sets the system time (Hour, Minute, Second) and date (Month, Day, Year).
5-6
Internal Numlock
USB
5-7
Advanced Menu
The Advanced menu contains the input/output configuration settings of
the system.
Geyserville Support
5-8
COM Ports (COM3/4)
Allows you to assign COM3 and COM4 to specific functions that you
wish to use. In general, COM3 can be assigned to touchscreen, while
COM4 can be assigned to RS-232C. Select Disabled if you need the
resource 2E8/IRQ7 of COM4 for another device.
5-9
LPT Mode
Sets the communication compatibility mode for the IR port. Select
according to the type of device with which the Tablet PC is to
communicate with.
Sets the address for the LPT port (parallel port).
5-10
HDD Heater
Function Key 1 Define (FN1)
Function Key 2 Define (FIN2)
Function Key 3 Define (Fin3)
These 3 items allow user to define the corresponding function key
associated with the 3 function buttons ( , , ) found on the front
panel..
5-11
Power Button Define
Enables or disables the beep sound when any hot-key is pressed.
5-12
Security Menu
The Security menu contains the security setting that safeguards your
system against unauthorized use.
Sets the Setup password. A password is required for running the SCU
program. When setting password, make sure that NumLock is off, then
type the password in the entry field and press Enter. Confirm your
password by typing it again and pressing Enter. For the password to take
effect, enable the Enable Setup Password item.
5-13
Hard Disk Boot Sector
Sets the system password. A password is required for starting up the
system and running the SCU program. When setting password, make sure
that NumLock is off, then type the password in the entry field and press
Enter. Confirm your password by typing it again and pressing Enter. For
the password to take effect, enable the Enable Password item.
5-14
Boot
Set the first, second, third, and fourth booting device. The system will try
to boot from the first device but if it is not available, will try the next boot
device. If you set the first boot device to Floppy Disk Drive, the system
will boot from the Floppy Disk Drive first. The options are Hard Disk C,
CD-ROM Drive and LAN. The default setting is Diskette A, Hard Disk
C, CD-ROM Drive then LAN.
5-15
Exit
The Exit menu allows you to leave the SCU program. After finished with
your settings, you must save and exit so that the new settings can take
effect.
Save Changes and Exit saves the changes you have made and exit the
SCU program.
Discard Changes and Exit exits the SCU program without saving the
changes you have made.
Get Default Values loads factory default values for all the items.
Load Previous Values restores previous values for all the items.
CHAPTER
6
Installing Software Drivers
To take full advantage of the unique features of your Tablet PC, some
operating systems require custom software, known as drivers, to be
installed.
If you purchased the Tablet PC with Windows pre-installed, your dealer
may have already installed the drivers. If not, you need to install the drivers
using the CD supplied with your Tablet PC.
This chapter describes how to install the drivers.
6-2 Installing Software Drivers
How to Use the CD
NOTE:
? The drivers may have been updated after this manual was published. For drivers
upgrade, please contact your dealer.
? You can always find README or document files on the CD. These files contain
the latest information from the software supplier. Please read the files together
with this chapter.
NOTE:
? This CD supports Windows 98, Windows 2000, and Windows NT 4.0. Other
systems are not supported.
? The available items may differ according to your computer model and operation
system.
You can set up the following drivers from the CD:
?? Mitsumi USB Floppy driver
NOTE: If you are using Windows 2000, you will not need to install this driver. Windows NT
does not support USB device.
?? ATI VGA driver
?? Crystal Audio driver
?? Modem driver
?? Realtek LAN driver
?? Touchscreen driver (PenMount Utility)
?? FIR driver
NOTE: If you are using Windows 2000, you will not need to install this driver. Windows NT
4.0 does not support FIR.
?? Card Wizard driver
NOTE: If you are using Windows 98 or Windows 2000, you will not need to install this driver.
Installing Software Drivers 6-3
A Setup program is provided on the CD. To run the program, simply insert
the CD and the following screen will appear. In case the autorun function
of your CD drive is not enabled, then click on “Start”, then “Run”. Specify
the CD drive and choose autorun.exe.
6-4 Installing Software Drivers
Installing Drivers for Windows 98
To set up the necessary drivers for Windows 98, click on “Windows 98”
on the initial screen. The following screen appears:
VGA The video driver allows you to select high-resolution
displays with richer colors. It can drive LCD displays
as well as CRT displays.
Audio The audio driver allows you to take full advantage of
the audio subsystem.
Touchscreen The touchscreen driver allows you to use your fingers
as well as the touchscreen pen as a pointing device.
USB Floppy The floppy drive driver allows you to use the
USB
floppy disk drive.
Modem The modem driver allows you to transmit information
over a standard telephone line through the RJ-11 port.
Installing Software Drivers 6-5
To install the necessary driver, just click on the particular option and follow
the onscreen instructions to continue and complete installation.
Touchscreen Driver
1. Insert the driver CD into the drive.
2. Click on “Windows 98”, then “Touchscreen” and follow the onscreen
instructions to continue.
3. When finished installing, select “Yes” to reboot your system. The driver
should now be loaded.
4. After the system has finished rebooting, click on the “PenMount Monitor”
icon located on the taskbar to bring up the “PenMount Control Panel”.
5. Select the “Calibrate” folder and click on “Calibrate.”
6. Click on the four sides (points) and the plus-sign “+” on the screen to
calibrate your touchscreen pen for use on the Tablet PC.
6-6 Installing Software Drivers
Installing Drivers for Windows 2000
To set up the necessary drivers for Windows 2000, click on “Windows
2000” on the initial screen. The following screen appears:
VGA The video driver allows you to select high-resolution
displays with richer colors. It can drive LCD displays
as well as CRT displays.
Modem The modem driver allows you to transmit information
over a standard telephone line through the RJ-11 port.
Touchscreen The touchscreen driver allows you to use your fingers
as well as the touchscreen pen as a pointing device.
Audio The audio driver allows you to take full advantage of
the audio subsystem.
To install the necessary driver, just click on the particular option and follow
the onscreen instructions to continue and complete installation.
Installing Software Drivers 6-7
Touchscreen Driver
System Hardware Detection
1. Click on “Start”, then “Settings”, then “Control Panel”, then “System”, and
select the “Device Manager” tab.
2. Under the item “Other devices” a question mark appears in front of the
sub-item “Unknown Device.”
3. Right-click on the item “Unknown Device” and click on “Properties.” When
the “Properties” window appears, click on “Reinstall Driver”.
4. When the “Update Device Driver Wizard” window appears, click on “Next”
and follow the onscreen instructions to continue.
5. When you are asked for the driver location, make sure the driver CD is in the
drive and specify the \W2000\TOUCHSCREEN\DMC9000.INF file.
6. When the “Digital Signature Not Found” window appears, click on “Yes” to
continue and exit.
7. Click on “Start”, then “Settings”, then “Control Panel”.
8. Right-click on “System” and select “Properties”.
9. On the “System Properties” window, click on “Device Manager”.
10. On the “Device Manager” window, “DMC9000” should appear under the
item “Mice and other pointing devices”. Right-click on “DMC9000” and
click on “Properties”.
11. Note the message on the window for “Device status” and make sure that
“Use this device (enable) should be selected on the “Device usage:”
window.
12. Click on “Close” to exit.
6-8 Installing Software Drivers
Software Installation
1. Reinsert the driver CD into the drive.
2. Click on “Windows 2000”, then “Touchscreen” and follow the onscreen
instructions to continue.
3. When finished installing, select “Yes” to reboot your system. The driver
should now be loaded.
4. After the system has finished rebooting, click on the “PenMount Monitor”
icon located on the taskbar to bring up the “PenMount Control Panel”.
5. Select the “Calibrate” folder and click on “Calibrate.”
6. Click on the four sides (points) and the plus-sign “+” on the screen to
calibrate your touchscreen pen for use on the Tablet PC.
Installing Software Drivers 6-9
Installing Drivers/Utility for Windows NT 4.0
To set up the necessary drivers/utility for Windows NT 4.0, click on
“Windows NT” on the initial screen. The following screen appears:
VGA The video driver allows you to select high-resolution
displays with richer colors. It can drive LCD displays
as well as CRT displays.
Audio The audio driver allows you to take full advantage of
the audio subsystem.
Modem The modem driver allows you to transmit information
over a standard telephone line through the RJ-11 port.
Touchscreen The touchscreen driver allows you to use your fingers
as well as the touchscreen pen as a pointing device.
Card Wizard The PCMCIA Card utility enhances the ability of
your Tablet PC to use a wider range of PC Cards like
6-10 Installing Software Drivers
flash memory, SRAM, modem, LAN, and SCSI
cards.
To install the necessary driver/utility, just click on the particular option and
follow the onscreen instructions to continue and complete installation.
Touchscreen Driver
1. Insert the driver CD into the drive.
2. Click on “Windows NT”, then “Touchscreen” and follow the onscreen
instructions to complete the installation.
3. When finished installing, the driver should now be loaded and the “PenMount
Control Panel” window appears.
4. On the “Configure” tab, click on “Detect” to allow the system to
automatically detect the IRQ number and I/O address as well as select the
serial port. Click on “Apply”, then “OK”. You will be asked to reboot the
system to validate the required configuration.
5. After the system has finished rebooting, click on the “PenMount Monitor”
icon located on the taskbar to bring up the “PenMount Control Panel”.
6. Select the “Calibrate” folder and click on “Calibrate”.
7. Click on the four sides (points) and plus-sign “+” on the screen to calibrate
your touchscreen pen for use on the Tablet PC.
Modem Driver
1. Restart your system and quickly press F2 to enter the SCU Setup.
2. Enter the “Advanced” menu and select “COM Port (COM3/4)”.
3. Select the option “Touchscreen/Disabled”.
Installing Software Drivers 6-11
4. Select “LPT Port” and select the option “Disabled”.
5. Insert the driver CD into the drive.
6. Click on “Windows NT”, then “Modem” and follow the onscreen
instructions to complete the installation.
6-12 Installing Software Drivers
Other Drivers and Utilities
0VMAKFIL Utility
CAUTION: Check with your dealer to find out if the Suspend-to-disk file (partition) is already
created. If it is not created and you want to create the Suspend-to-disk file by yourself, make
sure that your hard disk is empty. That is, your hard disk has not been partitioned by the
FDISK program. If any partition exists, you have to use the FDISK program to delete all
partitions before you can use the 0VMAKFIL utility.
The 0VMAKFIL.EXE utility program allows you to create in your hard
disk the Suspend-to-disk file (partition), which is required for the
Suspend-to-disk function of your Tablet PC.
Follow these steps to create the suspend-to-disk partition:
1. Boot your system by CD-ROM.
2. Now you can run the 0VMAKFIL program under the S2D Utility
directory on the CD, following this command syntax:
0VMAKFIL -Pnn
where nn specifies the size (in MB) of the partition.
You can have the size larger than your current system memory size for
future upgrade of your memory. If you do not specify the parameter, the
default size will be your system RAM plus 4 MB. The extra 4 MB is for
the overhead of the program and data held in video memory.
You can clear the contents of the partition using the 0VMAKFIL -C
command. The command is useful only when you are backing up the data
in the hard disk drive.
CHAPTER
7
Caring for the Tablet PC
Taking good care of your computer will ensure a trouble-free operation
and reduce the risk of damage to your computer.
This chapter gives you guidelines covering these areas of maintenance:
?? How to protect the computer
?? What to note when using and storing the computer
?? How to clean the computer
?? What to note when using the battery pack
?? What to note when traveling with the computer
7-2 錯誤! 尚未定義樣式。
Protecting the Computer
To safeguard the integrity of your computer data as well as the computer
itself, you can protect the computer in several ways as described in this
section.
Using the Password
The power-on password protects your computer against unauthorized
use. If the password is set, the prompt requesting for the password
appears on the screen whenever the computer is turned on.
The password is set via the SCU program. See “Security Menu” in
Chapter 5 for instructions.
Using an Anti-Virus Strategy
New viruses are always being developed nowadays and they are attacking
computers even more easily with emails so commonly used worldwide.
The Security feature of the SCU program protects the boot sector of the
hard disk. To enable the function, see “Security Menu” in Chapter 5 for
instructions.
You can also install a virus-detecting program to monitor potential
viruses that could damage your files.
錯誤! 尚未定義樣式。 7-3
Taking Care of the Tablet PC
Location Guidelines
?? Use the computer where the temperature is between 10?C (50?F) and
35?C (95?F).
?? Avoid placing the computer in a location subject to high humidity,
extreme temperatures, mechanical vibration, direct sunlight, or heavy
dust.
?? Do not cover or block any ventilation openings on the computer. For
example, do not place the computer on a bed, sofa, rug, or other
similar surface. Otherwise, overheating may occur that results in
damage to the computer.
?? Keep the computer at least 13 cm (5 inches) away from electrical
appliances that can generate a strong magnetic field such as a TV,
refrigerator, motor, or a large audio speaker.
?? Do not move the computer abruptly from a cold to a warm place. A
temperature difference of more than 10?C (18?F) will cause
condensation inside the unit, which may damage the storage media.
?? Do not place the computer on an unsteady surface.
General Guidelines
?? Do not place heavy objects on top of the Tablet PC as this may
damage the display.
?? The screen surface is easily scratched. Do not use paper towels to
clean the display. Avoid touching it with a ballpoint pen or pencil.
?? To maximize the life of the backlight in the display, allow the
backlight to automatically turn off as a result of power management.
Avoid using a screen saver or other software that prevents the power
management from working.
7-4 錯誤! 尚未定義樣式。
Cleaning Guidelines
?? Never clean the computer with its power on.
?? Use a soft cloth moistened with water or a non-alkaline detergent to
wipe the exterior of the computer.
?? Gently wipe the display with a soft, lint-free cloth. Do not use alcohol
or detergent on the display.
?? Dust on the IR port can interfere with data transfer. Wipe the port
with a soft, dry cloth.
?? Dust or grease on the touchscreen can affect its sensitivity. Clean the
touchscreen by using adhesive tape to remove the dust and grease on
its surface.
Battery Pack Guidelines
?? Recharge the battery pack when it is nearly discharged. When
recharging, make sure the battery pack is fully charged. Doing so
may avoid harm to the battery pack.
?? Operate the computer with the battery pack installed even when using
external power. This ensures that the battery is fully charged.
?? If you will not be using the computer for a long period of time (more
than two weeks), remove the battery pack from the computer.
?? If you remove the battery pack, make sure the battery terminals do
not contact any conductors such as metal objects or water. Otherwise,
the battery may become unusable as a result of a short circuit.
?? If you need to store the battery pack, store it in a cool, dry place.
Never allow the temperature to exceed 60?C (140?F).
?? Do not leave the battery pack in storage for more than 3 months
without recharging it.
錯誤! 尚未定義樣式。 7-5
When Traveling
?? Before traveling with your computer, make a backup of your hard
disk data into floppy disks or other storage devices. As an added
precaution, bring along an extra copy of your important data.
?? Make sure the battery pack is fully charged.
?? Make sure the computer is turned off.
?? Do not leave objects that will press onto the display.
?? Disconnect the AC adapter from the computer and take it with you.
Use the AC adapter as the power source and as a battery-charger.
?? Hand-carry the computer. Do not check it in as luggage.
?? Allow extra time for airport security. Many airports inspect
electronic devices carefully.
?? If you need to leave the computer in the car, put it in the trunk of the
car to avoid exposing the computer to excessive heat.
?? When going through airport security, it is recommended that you
send the computer and floppy disks through the X-ray machine (the
device you set your bags on). Avoid the magnetic detector (the device
you walk through) or the magnetic wand (the hand-held device used
by security personnel).
?? If you plan to travel abroad with your computer, consult your dealer
for the appropriate AC power cord for use in your country of
destination.
CHAPTER
8
Troubleshooting
Hardware, software, or a combination of both can cause computer
problems. When you encounter any problem, it might be a typical
problem that can easily be solved.
This chapter tells you what actions to take when solving common
computer problems. It is divided into three sections:
?? Preliminary checklist
?? Solving common problems
?? Resetting the computer
8-2 錯誤! 尚未定義樣式。
Preliminary Checklist
Here are helpful hints to follow before you take further actions when you
encounter any problem:
?? Try to isolate which part of the computer is causing the problem.
?? Make sure that you turn on all peripheral devices before turning on
the computer.
?? If an external device has a problem, make sure that the cable
connections are correct and secure.
?? Make sure that the configuration information is properly set in the
SCU program.
?? Make sure that all the device drivers are correctly installed.
?? Make notes of your observations. Are there any messages on the
screen? Do any indicators light? Do you hear any beeps? Detailed
descriptions are useful to the service personnel when you need to
consult one for assistance.
If any problem persists after you follow the instructions in this chapter,
contact an authorized dealer for help.
錯誤! 尚未定義樣式。 8-3
Solving Common Problems
For easy reference, the problems are divided into these categories.
Problem Type Go to
Battery problems P. 8-4
CD/DVD drive problems P. 8-4
Display problems P. 8-5
Floppy disk drive problems P. 8-7
Hardware device problems P. 8-8
Hard disk drive problems P. 8-8
Infrared problems P. 8-9
Keyboard and mouse problems P. 8-9
LAN problems P. 8-10
Modem problems P. 8-10
PC Card problems P. 8-11
Power Management problems (for Windows) P. 8-11
Printer problems P. 8-12
Software problems P. 8-12
Sound problems P. 8-13
Startup problems P. 8-14
Other problems P. 8-15
8-4 錯誤! 尚未定義樣式。
Battery Problems
The battery does not charge (Battery Charge indicator does not
appear).
?? Make sure that the AC adapter is properly connected.
?? Make sure that the battery is not too hot – gets above 40oC (104oF) or
too cold – below 0oC (32oF). Allow time for the battery pack to
return to room temperature.
?? Make sure that the battery pack is installed correctly.
?? Make sure that the battery terminals are clean.
The operating time of a fully charged battery becomes shorter.
?? If you often partially recharge and discharge, the battery might not
be charged to its full potential. Initialize the battery to solve the
problem. (See “Initializing the Battery Pack” in Chapter 3 for
instructions.)
?? Make sure that power to the Tablet PC is off. If you use the Tablet
PC during recharging for more than 4 hours, the recharging will stop
no matter whether the battery has been fully charged or not. If this
happens, you can disconnect and then reconnect the AC adapter to
start the recharging again.
The battery operating time indicated by the battery meter does not
match the actual operating time.
?? The actual operating time can be different from the estimated time,
depending on how you are using the computer. If the actual
operating time is much less than the estimated time, initialize the
battery. (See “Initializing the Battery Pack” in Chapter 3 for
instructions.)
CD/DVD Drive Problems
The CD/DVD drive cannot read a CD.
?? Make sure that the CD is correctly seated in the tray, with the label
facing up.
錯誤! 尚未定義樣式。 8-5
?? Make sure that the CD is not dirty. Clean the CD with a CD cleaning
kit, available in most computer stores.
?? Make sure that the CD/DVD drive driver is installed correctly.
?? Make sure that the computer supports the CD or the file format
contained.
You cannot eject a CD.
?? The CD is not properly seated in the drive. Manually release the CD
following the method described next:
Turn off the system.
Insert a small rod, such as a straightened paper clip, into the
drive’s manual eject hole and push firmly to release the tray.
Pull the tray out until fully extended, and then remove the CD.
Display Problems
Nothing appears on the screen.
?? If the power-on indicator is not on, check the electrical outlet, the
plugs and power cords.
?? If the power button does not respond to a light touch, press the
button firmly.
?? If you are using the battery power, make sure that it has a charge
remaining and that it is installed correctly.
?? During operation, the screen may automatically turn off as a result of
power management. Press any key to see if the screen comes back.
?? The brightness level might be too low. Increase brightness by
pressing on the brightness/volume control button on the front panel
of the Tablet PC.
?? The display output might be set to an external monitor.
?? Reset the Tablet PC by pressing the reset button on the right side of
the computer or by pressing Ctrl+Alt+Del keys if you are using an
external keyboard.
8-6 錯誤! 尚未定義樣式。
?? Try turning the computer off, wait a few seconds, then turn it back
on.
The characters on the screen are dim.
?? Adjust the brightness.
Bad dots appear on the display at all times.
?? A small number of missing, discolored, or bright dots on the screen
are an intrinsic characteristic of TFT LCD technology. It is not
regarded as a LCD defect. The Inspection Standard generally agreed
in the LCD industry allows a maximum of 8 pixels on a unit.
Term definition:
Bright dots
When the LCD screen is lighted, dots appear bright
at a dark area. Red/green/blue bright dots also
count.
Dark dots
When the LCD screen is lighted, dots appear black
at bright areas.
Distance between
defective dots
The minimum distance between two defective dots.
Adjacent defective dots
Defective dots within a radius of 10 mm.
Defective dots
Distance between
defective dots
Two adjacent
defective dots Three or more adjacent
defective dots
LCD Type
Bright
Dark
Bright
Dark
Bright
Dark Bright Dark
Total
12.1" SVGA
N<5 N<5 <15mm
<15mm
<2 Pairs
<2 Pairs
Not allowed
Not allowed
N<8
13.3" XGA N<5 N<7 <15mm
<15mm
<2 Pairs
<2 Pairs
Not allowed
Not allowed
N<9
14.1" XGA N<5 N<7 <15mm
<15mm
<2 Pairs
<2 Pairs
Not allowed
Not allowed
N<9
15" XGA N<8 N<8 <15mm
<15mm
<2 Pairs
<2 Pairs
Not allowed
Not allowed
N<10
18" XGA N<9 N<15
<5mm <20mm
<3 Pairs
<5 Pairs
Not allowed
Not allowed
N<20
Resolution cannot be adjusted to desired setting.
?? Make sure that the video driver is installed correctly.
The external monitor displays nothing.
?? Make sure that the monitor is turned on.
?? Make sure that the monitor’s signal cable is properly connected.
?? Check if the Setup item Display Mode on the Main menu of the
SCU program is configured correctly.
錯誤! 尚未定義樣式。 8-7
Simultaneous display does not work.
?? Make sure that you turn on the external monitor before turning on
the computer.
?? Check the Setup item Display Mode on the Main menu of the SCU
program is configured correctly.
Floppy Disk Drive Problems
The Floppy Disk Drive In-use Indicator stays on.
?? Make sure that the floppy disk is not physically damaged.
?? Make sure that the floppy disk is inserted correctly.
The disk drive cannot write to a floppy disk.
?? Make sure that the floppy disk is formatted.
?? Make sure that the floppy disk is not write-protected.
?? Make sure that you are writing to the correct drive.
?? Make sure that there is enough space left on the floppy disk.
?? Make sure that the floppy disk is not physically damaged.
The disk drive cannot read a floppy disk.
?? Make sure that the floppy disk is formatted.
?? Make sure that you are reading the correct drive.
Hardware Device Problems
The computer does not recognize a newly installed device.
?? The device may not be correctly configured in the SCU program.
Run the SCU program to identify the new type.
?? Make sure if any device driver needs to be installed. (Refer to the
documentation that came with the device.)
8-8 錯誤! 尚未定義樣式。
?? Make sure if the device needs any jumper or switch settings. (Refer
to the documentation that came with the device.)
?? Check the cables or power cords for correct connections.
?? For an external device that has its own power switch, make sure that
the power is turned on.
Hard Disk Drive Problems
The hard disk drive error message appears on the screen.
?? Insert a bootable diskette and check the integrity of your hard drive.
?? The hard disk drive has defects. Ask your dealer for help.
The hard disk drive operations seem slow.
?? The data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
The hard disk drive in-use indicator glows without blinking.
?? The data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
Infrared Problems
The IR port does not work.
?? Make sure that the IR ports of the two device face each other within a
?15-degrees angle and 1 meter (3 feet) distance and there are no
obstructions in between.
?? Make sure that the device connected is using an equivalent speed.
?? Make sure that the IrDA Fast Infrared Port is set to HP
HSDL-2300/3600.
?? Make sure that the IR port is set correctly in the SCU program.
?? If you are printing to an infrared printer, make sure that the
appropriate driver is installed.
錯誤! 尚未定義樣式。 8-9
?? If you are using any file transfer functions, make sure that both the
computer and the IR device have the appropriate software running.
?? Make sure that there is no device radiating infrared rays, such as
remote-controlled devices or wireless headphones, near the
computer or device.
?? Make sure that no direct sunlight or fluorescent lamps are near the
computer or device.
?? Make sure that the IR ports are clean.
Keyboard and Mouse Problems
The keyboard does not respond.
?? Try connecting another external keyboard. If it works, replace the
former keyboard as it may be defective.
The numeric keypad is disabled.
?? Make sure that the Num Lock is switched on. (Check if the Num Lock
Indicator appears or not.)
The external keyboard does not work.
?? Make sure that the keyboard cable is properly connected.
The PS/2 mouse does not work.
?? Make sure that the mouse cable is properly connected.
?? Make sure that the pointing device is enabled in the SCU program.
The serial mouse does not work.
?? Make sure that the mouse cable is properly connected.
?? Make sure that you connect the mouse before booting the computer.
?? Make sure that the serial port is enabled in the SCU program.
8-10 錯誤! 尚未定義樣式。
LAN Problems
I cannot access the network.
?? Make sure that the LAN driver is correctly installed.
?? Make sure that the LAN cable is properly connected to the RJ-45
connector and the network hub.
?? Make sure that the network configuration is appropriate.
?? Make sure that the user name or password is correct.
Modem Problems
The modem does not work.
?? Make sure that the modem driver is correctly installed.
?? Make sure that the telephone line is properly connected.
?? Make sure that the COM port in the communication software is
correctly set.
?? Turn off power management.
PC Card Problems
The PC Card does not work.
?? Make sure that the PC Card is correctly seated.
?? If the card requires an IRQ (interrupt request), make sure that there is
one available.
?? The PC Card may be attempting to use a COM port in a manner that
conflicts with the COM port being used by another device. Try
running the SCU program to change the COM port setting. If your
PC Card uses COM1, set COM1 as Disabled. If your PC Card uses
COM2, set COM2 as Disabled. If your PC Card uses COM4, set
COM4 at Disabled.
錯誤! 尚未定義樣式。 8-11
WARNING: COM3 is reserved for use by the touchscreen, do not disable it. If COM1/2
is disabled and COM3/4 is enabled on the SCU Setup (refer to chapter 5), upon booting
system would recognize the enabled COM3/4 and designate it as COM1/2.
The following table is the default settings:
COM Port I/O (Input/Output) Port
IRQ (Interrupt Request)
COM1 (available) 3F8 IRQ4
COM2 (available) 2F8 IRQ3
COM4 (available) 2E8 IRQ7
COM3 (reserved for
touchscreen only) 3E8 IRQ5
The PC Card stops communicating properly.
?? The application may have been reset when the computer is turned off
or in Standby mode. Exit and restart the application.
Power Management Problems (for Windows)
The computer does not enter Standby or Suspend mode
automatically.
?? If you have a connection to another computer, the computer does not
enter Standby or Suspend mode if the connection is actively in use.
?? Make sure that the Standby or Suspend time-out is enabled.
The computer does not enter Standby or Suspend mode
immediately.
?? If the computer is performing an operation, it normally waits for the
operation to finish.
The computer does not resume from Standby or Suspend mode.
?? The computer automatically enters Standby or Suspend mode when
the battery pack is empty. Do any one of the following:
? Connect the AC or car adapter to the computer.
? Replace the empty battery pack with a fully charged one.
8-12 錯誤! 尚未定義樣式。
The computer does not enter Suspend mode.
?? If you are using Windows 98, make sure that the Suspend-to-disk
partition or file exists.
?? You might be using a PC Card that prevents the computer from
entering Suspend mode. To enter the mode, stop the communication
program and then remove the card or stop the card.
Printer Problems
The printer does not work.
?? Make sure that the printer is turned on (if it comes with an
independent power source) and is online (ready to use).
?? Make sure that the printer’s signal cable is properly connected.
?? Make sure that the printer driver is correctly installed.
?? Make sure that you have assigned the printer port correctly in your
operating system or application program.
?? Make sure that the printer port is enabled in the SCU program.
The printer prints garbled information.
?? Make sure that the printer driver is correctly installed.
?? Make sure that the printer cable is properly connected.
Software Problems
An application program does not work correctly.
?? Make sure that the software is correctly installed.
?? If an error message appears on the screen, consult the software
program’s documentation for further information.
?? If you are sure the operation has stopped, reset the computer. (See
“Resetting the Computer” in this chapter.)
錯誤! 尚未定義樣式。 8-13
Sound Problems
No sound is produced.
?? Make sure that the volume control is not set too low.
?? Make sure that the audio driver is correctly installed.
?? Make sure that the computer is not in Standby mode.
?? If using an external speaker, make sure that the speaker is properly
connected.
Distorted sound is produced.
?? Make sure that the volume control is not set too high or too low. In
most cases, a high setting can cause the audio electronics to distort
the sound.
The sound system does not record.
?? Adjust the playback or recording sound levels.
The external microphone or audio device does not work.
?? Make sure that the microphone is connected to the proper connector
on the computer.
?? Make sure that your computer is equipped with the driver needed.
?? Click the speaker symbol on the taskbar and check the Windows
volume control.
?? Check the volume control of your computer.
Startup Problems
When you turn on the computer, it does not respond and the Power
Indicator does not appear.
?? If you are using an external AC power, make sure that the AC
adapter is correctly and securely connected. If so, make sure that the
electrical outlet works properly.
8-14 錯誤! 尚未定義樣式。
?? If you are using the battery power, make sure that the battery is not
discharged.
When you turn on the computer, it stops after POST.
?? Restart your computer.
The message “Operating system not found” appears on the screen
after you turn on the computer.
?? Make sure that there is no floppy disk in the floppy disk drive. If
there is, remove it and restart the system.
?? If this message appears when you are booting from the hard disk,
insert a bootable disk in the floppy disk drive and check the
condition of the hard disk.
The message “Invalid system disk” or “Disk error” appears on the
screen after you turn on the computer.
?? If you are deliberately trying to boot from a floppy disk, replace the
disk with a bootable one and press any key to continue booting.
?? If you are booting from the hard disk, make sure that there is no
floppy disk in the floppy disk drive. If there is, remove it and restart
the system.
?? If this message appears when you are booting from the hard disk,
insert a bootable disk in the floppy disk drive and check the
condition of the hard disk.
Other Problems
The date/time is incorrect.
?? Correct the date and time via the operating system or SCU program.
?? After you have performed everything as described above and still
have the incorrect date and time every time you turn on the
computer, the RTC (Real-Time Clock) battery is at the end of its life.
Call an authorized dealer to replace the RTC battery.
錯誤! 尚未定義樣式。 8-15
Resetting the Computer
You may have to reset (reboot) your computer on some occasions when
an error occurs and the program you are using hangs up.
If the system operation seems to hang up, first wait. It is possible that the
system is processing data. Periodically check the hard disk drive in-use
indicator, if it flashes irregularly, the program may be accessing data and
preventing you from using the keyboard. If you are sure the operation has
stopped and you cannot use the “restart” function of the operating system,
reset the computer.
Reset the computer by any one of these method:
?? Press Ctrl+Alt+Del if you have an external keyboard connected.
?? If the above action does not work, turn off the system. Wait for at
least five seconds and turn it on again.
?? It the above does not work, insert a small rod, such as a straightened
paper clip, into the reset switch on the right side of the Tablet PC and
press firmly.
CAUTION: Resetting will cause any unsaved data to be lost.
Reset Switch
8-16 錯誤! 尚未定義樣式。
?? It the above two methods does not work, insert a small rod, such as a
straightened paper clip, into the keyboard BIOS reset switch on the
inside of the secondary battery compartment of the Tablet PC and
press firmly.
Reset Switch
APPENDIX A
Specifications
NOTE: Specifications are subject to change without any prior notices.
Parts Specifications
CPU Intel Pentium M Processor LV1.1GHz in ?-FCBGA package FSB
400MHz
CPU thermal ceiling: 12W
Cache Memory on-die 1MB L2 cache
ROM BIOS 512 KB Flash EEPROM
System 256 MB, Max: 1GB RAM
Video Share system 4 MB (built-in on VGA chip)
Panel 10.4-inch TFT XGA LCD, resolution up to 1024×768
10.4-inch touch screen
Sunlight Readable Panel ( Transflective LCD ) optional
Video controller Integrated into ATI 3D RAGE Mobility-M or M1, hardware 2D/3D
video/graphics accelerator
Display
Video port VGA port via optional Port Replicator module
Keyboard (external/wireless) –
optional Standard keys, numeric keypad, 12 function keys, and Windows keys
Pointing device A touch-sensitive control pad with Microsoft Win mouse function
(Optional)
Rubber Keyboard
Floppy disk drive 3.5-inch, 1.44 MB (via optional USB FDD module on Expansion port)
Hard disk drive 2.5-inch, IDE, Ultra DMA33 supported
Storage
device
CD/DVD drive 24X CD-ROM or above
8X DVD-ROM or above
(both via optional CD/DVD-ROM module on Expansion port)
Audio controller AC 97 audio support
MS-Sound compatible
Built-in one speaker (Mono)
Audio
Audio port Two audio ports for Mic-in / Earphone-out
A-2
Parts Specifications
PCMCIA Type I or Type II x 1, Card Bus support
On front panel IR port for wireless keyboard
On left side HP-SIR port, RJ-11 fax/modem port
On right side Mic-in, Line-out , Private port (Serial port, USB 2.0 port
On underside CCD port (USB-type)
X-Bay interface
(option) IEEE 1394, serial ports, RJ-45, USB 2.0 port
GPRS/GSM or CDMA
GPS
PCMCIA Solt
I/O ports
Expansion port
(option) USB port (supports USB FDD boot-up function), serial port, ECP/EPP
parallel port, PS/2 port, Mic-in/Line-in/Line-out, CD-audio
Modem 56 Kbps internal Fax Modem
Wireless LAN Integrated WLAN (Intel Centrino platform) with built-in antenna
AC adapter 100?240 V AC, 50?60 Hz auto-switching
Car adapter 12~32 V DC
Primary
battery Li-ion battery, 6 cells
Power
Backup
battery
(option)
Li-ion battery, 4 cells; support hot swap
Dimension (W×D×H) 11.6×9.3×1.65 inch (295×236×42 mm)
Weight 5.06 lb (2.3kg) – without Backup battery pack
Temperature
Operating: 0?C (32?F) to 50?C (122?F); -20?C (-4?F) to 50?C (122?F)
(Optional)
Storage: –40?C (–40?F) to 70?C (158?F)
Environment
Humidity Operating: 5% to 95% RH, non-condensing