Getac Technology 305 NOTEBOOK PC User Manual IBU Notebook

Getac Technology Corporation NOTEBOOK PC IBU Notebook

Users Manual

Rugged Mobile Computing Solutions B300 USER’S MANUAL
April 2009 TRADEMARKS The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners. NOTE The information in this manual is subject to change without notice.
ENERGY STAR® is a government program that offers businesses and consumers energy-efficient solutions, making it easy to save money while protecting the environment for future generations. Please reference ENERGY STAR® related information from www.energystar.gov. As an ENERGY STAR® Partner, MiTAC Technology Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. An ENERGY STAR® qualified computer uses 70 % less electricity than computers without enabled power management features. Earning the ENERGY STAR®  When every home office is powered by equipment that has earned the ENERGY STAR®, the change will keep over 289 billion pounds of greenhouse gases out of the air.  If left inactive, ENERGY STAR® qualified computers enter a low-power mode and may use 15 watts or less. New chip technologies make power management features more reliable, dependable, and user-friendly than even just a few years ago.  Spending a large portion of time in low-power mode not only saves energy, but helps equipment run cooler and last longer.  Businesses that use ENERGY STAR® enabled office equipment may realize additional savings on air conditioning and maintenance.
 Over its lifetime, ENERGY STAR® qualified equipment in a single home office (e.g., computer, monitor, printer, and fax) can save enough electricity to light an entire home for more than 4 years.  Power management (“sleep settings”) on computers and monitors can result in much savings annually. Remember, saving energy prevents pollution Because most computer equipment is left on 24 hours a day, power management features are important for saving energy and are an easy way to reduce air pollution. By using less energy, these products help lower consumers’ utility bills, and prevent greenhouse gas emissions.
Table of Contents Chapter 1 Getting Started .................................................................. 1-1 Getting the Computer Running ............................................. 1-2 Unpacking ........................................................................... 1-2 Connecting to AC Power .................................................... 1-2 Opening the Cover ............................................................. 1-4 Turning On and Off the Computer ................................... 1-5 Taking a Look at the Computer ............................................. 1-6 Front Components .............................................................. 1-6 Rear Components ............................................................... 1-7 Right-Side Components ...................................................... 1-8 Left-Side Components ...................................................... 1-10 Bottom Components ........................................................ 1-11 Top-open Components ..................................................... 1-12 Closing Connector Covers ................................................ 1-15 Chapter 2 Operating Your Computer ................................................ 2-1 Starting and Stopping the Computer .................................... 2-2 Starting the Computer ....................................................... 2-2 Stopping the Computer ..................................................... 2-2 Using the Internal Keyboard .................................................. 2-4 Typewriter Keys .................................................................. 2-4 Cursor-Control Keys ............................................................ 2-4 Numeric Keypad ................................................................. 2-5 Function Keys ...................................................................... 2-6 Fn Key .................................................................................. 2-6 Hot Keys .............................................................................. 2-6 Using the Touchpad ................................................................ 2-9
Configuring the Touchpad ............................................... 2-11 Using the Touchscreen (Optional) ....................................... 2-12 Using the Quick Buttons ....................................................... 2-14 Using the Hard Disk Drive .................................................... 2-16 Installing a Second Hard Disk Drive (Optional) .............. 2-16 Using the Optical Drive (Optional) ...................................... 2-18 Inserting and Removing a Disc ........................................ 2-19 Using the Video Features ..................................................... 2-21 Configuring the Display Modes ....................................... 2-21 Using the Audio Features ..................................................... 2-22 Connecting Audio Devices ............................................... 2-23 Using the Communication Features .................................... 2-24 Using the Modem ............................................................. 2-24 Using the LAN ................................................................... 2-25 Using the Wireless LAN .................................................... 2-26 Using the Bluetooth® Feature .......................................... 2-29 Using the 3G Feature (Optional) ..................................... 2-34 Using the Fingerprint Sensor ............................................... 2-38 Enrolling Fingerprints ....................................................... 2-40 Changing the Settings ...................................................... 2-42 Chapter 3 Managing Power ............................................................... 3-1 AC Adapter .............................................................................. 3-2 Battery Pack ............................................................................. 3-3 Charging the Battery Pack ................................................. 3-3 Initializing the Battery Pack ............................................... 3-4 Checking the Battery Level ................................................ 3-5 Replacing the Battery Pack ................................................ 3-6 Installing a Second Battery Pack (Optional) ..................... 3-7 Battery Low Signals and Actions ..................................... 3-10 Power Management ............................................................. 3-11 Hibernation ....................................................................... 3-12 Power-Saving Tips ................................................................. 3-13
Chatper 4 Expanding Your Computer ............................................... 4-1 Connecting an External Monitor ........................................... 4-2 Connecting a Serial Device ..................................................... 4-4 Connecting a USB Device ....................................................... 4-5 Connecting an IEEE 1394 Device ............................................ 4-6 Using Smart Cards (Optional) ................................................. 4-7 Inserting and Removing a Smart Card .............................. 4-7 Using PC Cards ......................................................................... 4-8 Inserting and Removing a PC Card .................................... 4-8 Using ExpressCards (Optional) ............................................. 4-10 ExpressCard Type .............................................................. 4-10 Inserting and Removing an ExpressCard ......................... 4-11 Using the Card Reader .......................................................... 4-12 Using the Port Replicator (Optional) ................................... 4-14 System Memory Upgrade ..................................................... 4-15 Chapter 5 Using BIOS Setup and System Recovery .......................... 5-1 BIOS Setup ............................................................................... 5-2 When to Use........................................................................ 5-2 Starting BIOS Setup ............................................................ 5-2 Information Menu .............................................................. 5-4 Main Menu .......................................................................... 5-5 Advanced Menu .................................................................. 5-6 Security Menu ..................................................................... 5-7 Boot Menu .......................................................................... 5-9 Exit Menu .......................................................................... 5-10 System Recovery .................................................................... 5-11 Chapter 6 Using the TPM and P1 Utility ............................................ 6-1 Using TPM (Trusted Platform Module) .................................. 6-2 P1 Quick Launch Key Utility ................................................... 6-3 Chapter 7 Caring for the Computer ................................................... 7-1 Protecting the Computer ....................................................... 7-2 Using the Windows Security Center .................................. 7-2
Using the Cable Lock .......................................................... 7-3 Taking Care of the Computer ................................................ 7-4 Location Guidelines ............................................................ 7-4 General Guidelines ............................................................. 7-4 Cleaning Guidelines ............................................................ 7-5 Battery Pack Guidelines ...................................................... 7-5 Touchscreen Guidelines ...................................................... 7-6 When Traveling ....................................................................... 7-8 Chapter 8 Troubleshooting ................................................................ 8-1 Preliminary Checklist ............................................................... 8-2 Solving Common Problems .................................................... 8-3 Battery Problems ................................................................ 8-3 Bluetooth Wireless Transmission Problems ...................... 8-3 Display Problems ................................................................. 8-4 ExpressCard Problems ......................................................... 8-5 Hardware Device Problems ................................................ 8-5 Hard Disk Drive Problems ................................................... 8-5 Keyboard, Mouse, and Touchpad Problems ..................... 8-6 LAN Problems ...................................................................... 8-6 WLAN Problems .................................................................. 8-7 Modem Problems ................................................................ 8-8 Optical Drive Problems ....................................................... 8-8 PC Card Problems ................................................................ 8-9 Power Management Problems ........................................ 8-10 Software Problems ........................................................... 8-11 Sound Problems ................................................................ 8-11 Startup Problems .............................................................. 8-12 Other Problems ................................................................. 8-12 Resetting the Computer ....................................................... 8-13 Appendix A Specifications .................................................................... A-1 Appendix B Regulatory Information ................................................... B-1 On the Use of the System ....................................................... B-2
Class B Regulations ............................................................. B-2 Safety Notices ..................................................................... B-3 On the Use of the RF Device .................................................. B-6 USA and Canada Safety Requirements and Notices ........ B-6 European Union CE Marking and Compliance Notices .... B-9
Chapter 1 Getting Started Congratulations on purchasing this rugged computer. This chapter first tells you step by step how to get the computer up and running. Then, you will find a section briefly introducing the external components of the computer.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items:  Rugged computer  Accessories:  AC adapter  AC power cord  Touchscreen pen (depending on your model) Inspect all the items. If any item is damaged or missing, notify your dealer immediately. Keep the shipping carton and packing materials in case you need to ship or store the computer in the future. Connecting to AC Power The computer operates either on the external AC power or internal battery power. It is suggested that you use AC power when you start up the computer for the very first time. 1. Make sure that the computer is turned off. 2. Plug the DC cord of the AC adapter to the power connector of the computer ().
3. Plug the female end of the AC power cord to the AC adapter and the male end to an electrical outlet (). 4. When the AC adapter is connected, power is being supplied from the electrical outlet to the AC adapter and onto your computer. Now, you are ready to turn on the computer. 5. When the AC adapter is connected, it also charges the battery pack. The Battery Charge Indicator on the computer glows amber to indicate that charging is in progress. When the battery is fully charged, the Battery Charge Indicator ( ) glows green. (For information on using battery power, see Chapter 3.)  
Opening the Cover Open the top cover by pushing on the cover latch () and lifting up the cover (). You can tilt the cover forward or backward for optimal viewing clarity.
Turning On and Off the Computer Turning On 1. Make sure that the computer is connected to AC power or battery is fully charged. 2. Open the top cover 3. Press the power button ( ). 4. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system.
Taking a Look at the Computer Front Components Ref Component Description See Also  Top Cover Latch Locks the top cover. P. 1-4  3G Antenna Serves as the antenna for wireless modem. NOTE: For data transmission only. P. 2-34  Handle Provides a convenient way to carry the computer anywhere.
Rear Components Ref Component Description See Also  Power Connector Connects the AC adapter. P. 1-2  USB Port Connects a USB device, such as a USB flash disk, printer, digital camera, joystick, and more. P. 4-5  Expansion Bus Connector Connects to a Port Replicator. P. 4-14  VGA Connector Connects an external display monitor. P. 4-2  Serial Connector Connects a serial mouse or serial communication device. P. 4-4  Kensington Lock Locks the computer to a stationary object for security. P. 7-3
Right-Side Components Ref Component Description See Also  Expansion Card Slot Depending on your model, the expansion card slot can be any of the following: ExpressCard Slot Accepts an ExpressCard/34 or ExpressCard/54 for additional functions. P. 4-10 PCMCIA Slot Accepts a PC card for additional functions. P. 4-8  Mini IEEE 1394 Port Connects an IEEE 1394 device such as a scanner, printer, DVCAM, VCR, and more. P. 4-6  RFOn/Off Switch Serves as the master control that turns the wireless LAN radio, Bluetooth radio, and WWAN on/off. P. 2-27, 2-29, 2-34
Ref Component Description See Also  Card Reader Accepts a MultiMediaCard (MMC), Secure Digital (SD), Memory Stick (MS) or Memory Stick PRO (MS PRO) card for removable storage media. P. 4-12  RJ-11 Connector Connects the telephone line. P. 2-24  Hard Disk Drive Compartment Inside is the hard disk drive. P. 2-16  USB Ports Each of the two ports connects a USB device, such as a USB flash disk, printer, digital camera, joystick, and more. P. 4-5  Expansion Card Slot Depending on your model, the expansion card slot can be any of the following: Smart Card Reader Accepts a smart card for additional security feature. P. 4-7 PCMCIA Slot Accepts a PC card for additional functions. P. 4-8  GPS Antenna pass-through Connector Connects to the optional antenna for GPS receiver. (You need to install third-party GPS navigation software to take advantage of the GPS feature.)  Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device. P. 2-23 Microphone Connector Connects an external microphone. P. 2-23 RJ-45 Connector Connects the LAN cable. P. 2-25
Left-Side Components Ref Component Description See Also  Battery Pack Supplies power to your computer when external power is not connected. P. 3-3  Media Bay Depending on your model, the media bay may contain any of the following: Combo Drive/ DVD Dual Drive/ Super Multi Drive Accepts a compact disc for installing or loading software, accessing data, and playing music/video. P. 2-18 Secondary Battery Pack Supplies power to your computer when external power is not connected. P. 3-7 Secondary Hard Disk Drive Inside is the hard disk drive. P. 2-16
Bottom Components Ref Component Description See Also  Memory Slots Inside are the memory slots for expanding the memory size of your computer. P. 4-15
Top-open Components Ref Component Description See Also  LCD Screen Displays the output of the computer. May include the optional touchscreen feature. P. 2-21
Ref Component Description See Also  Quick Buttons P1 Turns off/on the LCD display and LED indicators, or User customized program quick launch key. NOTE: The function of P1 quick button depends on your setting in BIOS Setup program under the Advanced menu (see chapter 5 for details). P. 2-14 P. 6-3 Enables/disables power saving when using battery power. P. 2-14 Lights green when power saving mode is ON. Enables/disables sunlight readable display. P. 2-14 Lights green when sunlight readable mode is ON. Enables/disables light sensor. P. 2-14 Lights green when light sensor is ON.  Power Button Turns the computer power ON and OFF. P. 1-5  Touchscreen Pen Provides a convenient way to use the touchscreen. Can be stretched for better grip and handling. P. 2-12  Touchpad Serves as the pointing device of the computer. P. 2-9  Indicators Show the current status of the computer’s devices. Hard Disk Drive / Optical Drive Blinks green when computer is reading / writing data to the hard disk or optical drive. P. 2-16
Ref Component Description See Also Card Reader Blinks green when computer is reading / writing data to the storage card. P. 4-12 Caps Lock Lights green when Caps Lock is on. P. 2-5 Num Lock / HDD Heater Lights green when Num Lock is on. P. 2-27 Lights amber when optional hard disk heater is on (temperature is lower than 5oC when booting your computer).  Microphone Receives sound and voice for the computer. P. 2-22  Keyboard Serves as the data input device of the computer. P.2-4  Fingerprint Sensor Serves as the fingerprint verification, preventing unauthorized access to your computer. P. 2-38  Stereo Speaker Sends out sound and voice from the computer. P. 2-22 Indicators Show the current status of the computer’s devices. Power Lights green when computer is on. P. 1-5 Blinks green when computer is on Sleep mode. Battery Charge Lights green when the battery is fully charged. P. 3-3 Lights amber when the battery is being charged. Blinks red when the battery’s capacity is below 10 %. Blinks amber when the battery is in an abnormal condition.
Ref Component Description See Also WLAN Lights green when WLAN is on. P. 2-27 Bluetooth Lights green when Bluetooth is on. P. 2-29 3G Lights green when 3G is on. P. 2-34 Closing Connector Covers It is important to close the connector covers completely to ensure the waterproof integrity. When closing the covers, push the four corners and make sure that the cover fits in completely.
Chapter 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk. The computer will automatically load the OS after you turn it on. This process is called booting. Stopping the Computer When you finish a working session, you can stop the computer by turning off the power or leaving the computer in Sleep or Hibernation mode: To stop in this mode... Do this... To start up or resume again Off Click Start  Shut Down … This can prevent loss of unsaved data or damage to your software programs. If the system is locked up because of hardware or software problems, press the power button to turn off the computer. Press the power button. Sleep Depending on your settings in Windows, you can place the computer in Sleep mode by:  Closing the display cover Press any key.
To stop in this mode... Do this... To start up or resume again  Pressing the Fn+F12hot key  Pressing the power button Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by:  Closing the display cover  Pressing the Fn+F12hot key  Pressing the power button Press the power button. If you choose to stop in Sleep or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.)
Using the Internal Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus an Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories:  Typewriter keys  Cursor-control keys  Numeric keys  Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes. When the lock keys ( aps Lock and Num Lk) are pressed, their corresponding indicators light up. The Control (Ctrl) / Alternate (Alt) key is normally used in combination with other keys for program-specific functions. The Escape (Esc) key is usually used for stopping a process. Examples are exiting a program and canceling a command. The function depends on the program you are using. Cursor-Control Keys
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals.  Fn
Function Keys On the top row of the keys are the function keys: F1 to F12. Function keys are multi-purpose keys that perform functions defined by individual programs. Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way. Each time a hot key combination is pressed, it shifts the corresponding function to the other or next choice. You can easily identify the hot keys with the icons imprinted on the keytop. The hot keys are described next. Key Description Switches the wireless LAN radio on and off. Switches the night vision feature on and off for viewing the display when using night vision goggles (optional). Decreases the sound volume. Increases the sound volume.
Key Description Switches the display output to one of the following when external devices are connected. Upon booting the system with CRT: LCD CRT LCD & CRT NOTE: This function only applies to Plug & Play display devices. Decreases the LCD brightness. Increases the LCD brightness. Switches the touchscreen on and off (option). Switches the touchpad off and on. Switches the system sound output off (mute) and on. Switches the display on and off. Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.) Switches the keyboard backlight on and off (option).
Euro Symbol You can press the euro dollar sign on various keyboards.  To press the euro sign on a United States-International keyboard, hold down the Alt Gr key and press 5 (which has an euro sign on it).  To press the euro sign on a standard United States keyboard, hold down either of the Alt keys and type 0128 on the numeric keypad part of your keyboard.  To press the euro sign on an UK keyboard, hold down the Alt Gr key and press 4 (which has an euro sign on it). Windows Keys The keyboard has two keys that perform Windows-specific functions: Windows Logo key and Application key. The Windows Logo key opens the Start menu and performs software-specific functions when used in combination with other keys. The Application key usually has the same effect as a right mouse click. (See your Windows manual for more information.)
Using the Touchpad  Fn+F9  The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons. The touchpad consists of a rectangular pad (work surface) and a left and right buttons. To use the touchpad, place your forefinger or thumb on the pad. The rectangular pad acts like a miniature duplicate of your display. As you slide your fingertip across the pad, the pointer (also called cursor) on the screen moves accordingly. When your finger reaches the edge of the pad,
simply relocate yourself by lifting the finger and placing it on the other side of the pad. Here are some common terms that you should know when using the touchpad: Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Double-click Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location. –or– Gently tap twice on the pad and on the second tap, keep your finger in contact with the pad. Then, move your finger across the pad to drag the selected object to your destination. When you lift your finger from the pad, the selected object will drop into place.
Term Action Scroll To scroll is to move up and down or left and right in the working area on the screen. To move vertically, place your finger on the right or left edge of the pad and slide your finger up and down along the edge. To move horizontally, place your finger on the top or bottom edge of the pad and slide your finger left and right. This function works only after you install the touchpad driver supplied with the computer and it may not work for all applications. TABLE NOTE: If you swap the left and right buttons, “tapping” on the touchpad as an alternative method of pressing the left button will no longer be valid. Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vice versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, go to Control Panel  Hardware and Sounds  Mouse Properties.
Using the Touchscreen (Optional)   Fn+F8 The touchscreen is a touch-sensitive device that allows you to easily use the computer without a mouse or touchpad.
Here are some common terms that you should know when using the touchscreen: Term Action Click/Point Tap gently on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and drop Press lightly on the touchscreen and move your finger until you reach your destination (drag). Finally, release your finger (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Using the Quick Buttons Located on top of the keyboard are four quick buttons:  LCD display and LED indicators quick button (P1) to turn off the LCD display and LED indicator, or User customized program quick launch key (P1) – see chapter 6 for more details. P1Advanced  Power saving quick button ( ) to enter into power saving mode when using battery power. The system will turn down the panel backlight and sacrifice processing speed to gain more battery life. Lights green when power saving mode is enabled.  Sunlight readable quick button ( ) for enabling the sunlight readable LCD display. Lights green when sunlight readable mode is enabled.
 Light sensor quick button ( ) for adjusting the LCD brightness automatically based on your computer’s surrounding lighting condition. Lights green when light sensor is enabled.
Using the Hard Disk Drive Your computer comes with a removable hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch PATA (parallel ATA) / SATA (serial ATA) hard disk drive. This type of drive embodies the latest in fast, reliable mass storage by integrating all the control circuitry necessary for operation directly onto the drive itself. The system may come with an optional heater that automatically turns on for low temperature operation.    Installing a Second Hard Disk Drive (Optional) You can install a second hard disk drive to your computer. To install a second hard disk drive: 1. Make sure that system power is off. 2. Open the media bay cover by sliding the release latch towards the left.
3. Press upward the optical drive release latch () and carefully pull on the ribbon strip () to remove the optical drive. 4. Be careful to observe the correct orientation and slide the hard disk drive bracket into the media bay until it reaches the end. 5. Close the media bay cover to secure the hard disk drive bracket.  
Using the Optical Drive (Optional) Your computer may come with an optical drive, usually configured as drive D. Depending on the model, your drive is one of the following:  Combo drive can work both as a DVD drive (reading DVD discs in addition to CDs, audio CDs and CD-R/-RW discs), and also as a CD recorder (writing to CD-R/-RW discs).  DVD Dual drive besides the Combo drive function, can write to DVD+R/+RW/-R/-RW discs.  Super Multi drive besides the Combo drive function, can write to DVD+R/+RW/-R/-RW and DVD-RAM discs.    
Inserting and Removing a Disc Follow this procedure to insert or remove a disc: 1. Turn on the computer. 2. Open the media bay cover by sliding the release latch towards the left. 3. Press the eject button and the DVD tray will slide out partially. Gently pull on it until it is fully extended. 4. To insert a disc, place down the disc in the tray with its label facing up. Slightly press the center of the disc until it clicks into place. To remove a disc, hold the disc by its outer edge and lift it up from the tray.
5. Gently push the tray back into the drive. 6. Close the media bay cover. Eject button
Using the Video Features The video subsystem of your computer features:  13.3-inch wide TFT (Thin-Film Transistor) color LCD display with 1024×768 XGA resolution  Multi-display capability, which allows you to expand your desktop on the screen to another display device so that you have more desktop space to work on  Sunlight-readable LCD display by pressing sunlight readable quick button ( )  Automatically adjust the LCD brightness by pressing light sensor quick button ( )  Optional night vision display by pressing Fn + F2  Power Management Power Options  System SettingsConfiguring the Display Modes Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.)
Using the Audio Features The audio subsystem of your computer features:  Azalia interface (high density audio codec)  2-channel analog output  Built-in microphone ()  External audio connectors () and  Set of speakers () Ways of playing and recording sound vary with the operating system used. See your operating system documentation or online help for specific information.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices.  Audio Output Connector (green) can be connected to speakers, headphones, or earphone set.  Microphone Connector (pink) can be connected to an external microphone for recording voice or sound.
Using the Communication Features Using the Modem The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.    
Using the LAN The internal 10/100/1000Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN Depending on your model, an internal mini PCI-E wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include:  Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes support  WEP (Wired Equivalent Privacy) 64/128-bit data encryption  IEEE 802.11a/b/g/n standard compliance Technology Stated Maximum Throughput (Mbps) Data Rates (Mbps) Band (GHz) Modulation Technology 802.11a 54 54, 48, 36, 24, 18, 12, 9, 6 5.15 ~ 5.35 OFDM (Orthogonal Frequency Division Multiplexing) 802.11b 11 11, 5.5, 2, 1 2.412 ~ 2.462 DSSS (Direct Sequence Spread Spectrum) 802.11g 54 54, 36, 18, 9 2.4 OFDM (Orthogonal Frequency Division Multiplexing) 802.11n 100 Mbps or more 100 ~ 210 2.4 / 5 Spatial multiplexing, uses MIMO (multiple-input multiple-output) If your WLAN card was provided by your dealer instead of the computer manufacturer, contact your dealer for the correct driver to use.
Turning Off/On the WLAN Radio To turn on the WLAN radio: 1. Make sure that the RF switch is at the ON position. 2. Press Fn+F1 to turn on the WLAN radio (see “Hot Keys” in Chapter 2), indicated by the WLAN indicator ( ) glowing in green when on. If you need to temporarily turn off the radio, press Fn+F1. To resume network connection, press Fn+F1 again. It takes approximately 30 seconds for your computer to make a successful WLAN connection and approximately 10 seconds to disconnect. Connecting to a Wireless Network To connect to a wireless network: 1. Make sure that the WLAN radio is on (see the previous section). 2. Right-click the Wireless Network Connection icon located on the Windows system tray and select Connect to a network. 3. If any wireless network is detected, the following window appears on screen. Click the Show drop down menu and select Wireless.
4. Select a wireless network to connect to by clicking a selection, then click Connect. 5. Depending on the settings, you may be asked to enter a WEP key (refer to your Windows online help for more information on setting a wireless network connection).
Using the Bluetooth® Feature Depending on your model, your computer may incorporate the Bluetooth capability for short-range (about 10 meters) wireless communications between devices without requiring a cable connection. With Bluetooth wireless technology, data can be transmitted through walls, pockets and briefcases as long as two devices are within range. Turning On and Off the Bluetooth Feature 1. Make sure that the RF switch is at the ON position. 2. Right-click the GETAC Utility icon ( ) located on Windows system tray and select Quick Bar. 3. The following appears onscreen. To turn on the Bluetooth feature, click the Bluetooth quick button.
The Bluetooth indicator ( ) will glow in green. By default, your computer is in the general discoverable and pairable mode after the Bluetooth feature is turned on. 4. To turn off the Bluetooth feature, click the Bluetooth quick button again. The status of the Bluetooth connection is indicated by the Bluetooth icon located in the system tray in the lower-right part of the screen. Status Icon Off (blue with red logo) On (blue with white logo). Connected (blue with green logo) You can use the Bluetooth Utility to configure Bluetooth wireless connection settings and transfer files. Connecting to another Bluetooth Device 1. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.) 2. Right-click the icon, and then click Add New Connection.
3. The Add New Connection Wizard window appears. Select Express Mode (Recommended), and then click Next. 4. Select the device to connect to and click Next.
5. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information. Sending a File 1. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.) 2. Right-click the icon, and then click Wireless File Transfer.
3. In the Wireless File Transfer window, click Add to browse for the file to send. 4. Click the target device from the list, and then click Send to start the transfer procedure.
Using the 3G Feature (Optional) 3G is the third generation of mobile phone standards and technology, after 2G. It is based on the International Telecommunication Union (ITU) family of standards under the International Mobile Telecommunications programme. Unlike IEEE 802.11 networks, 3G networks are wide area cellular telephone networks. IEEE 802.11 networks are short range, high-bandwidth networks primarily developed for data.  
Installing a SIM Card To use the 3G feature (GSM/UMTS/EDGE/GPRS/EVDO/HSUPA) on your computer, you need to subscribe to 3G service and install the 3G SIM card from your service provider, network operator, or other vendor. To install the SIM card, follow these steps: 1. Make sure that the computer is not turned on or connected to AC power. 2. Open the media bay cover by sliding the release latch towards the left. 3. Press upward the optical drive release latch () and carefully pull on the ribbon strip () to remove the optical drive from the media bay. 4. Carefully place your computer upside down and locate the SIM card slot.
5. Insert the SIM card into the holder. Make sure the beveled corner on the SIM card is facing towards the slot and that the golden contact area on the card is facing downwards. 6. Replace the optical drive. 7. Close the media bay cover to secure the optical drive in place.
Turning On and Off the 3G Feature 1. Make sure that the RF switch is at the ON position. 2. Right-click the GETAC Utility icon ( ) located on Windows system tray and select Quick Bar. 3. The following appears onscreen. To turn on the 3G feature, click the 3G quick button. The 3G indicator ( ) will glow in green. 4. To turn off the 3G feature, click the 3G quick button again. You can use the 3G software application to configure 3G connection settings.
Using the Fingerprint Sensor To start using the fingerprint sensor: 1. Locate and slide open the fingerprint sensor cover.   2. Go to Start menu  Programs  Protector Suite QL  Control Center. The following screen appears.
The computer features the Fingerprint Control Center utility for enrolling your fingers for added security. It contains the following:  Fingerprints – for enrolling or editing fingerprint templates  Settings – for configuring the fingerprint software  Help – for browsing the Fingerprint Control Center online Help Start  Programs  Protector Suite QL  Help
Enrolling Fingerprints To start enrolling your fingerprint(s): 1. Click Fingerprints on the main screen. 2. Click Initialize. 3. The following screen appears. Read carefully the contents of the Welcome screen and then click Next to continue.
4. Follow the onscreen instructions to complete enrolling your fingerprint(s).
Changing the Settings To change the settings of your fingerprint software: 1. Click Settings on the main screen. 2. Click System Settings. 3. The following screen appears. Proceed to make the necessary settings to your fingerprint software.
4. Click OK after you have finished with your settings.
Chapter 3 Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter     The AC adapter serves as a converter from AC (Alternating Current) to DC (Direct Current) power because your computer runs on DC power, but an electrical outlet usually provides AC power. It also charges the battery pack when connected to AC power. The adapter operates on any voltage in the range of 100~240 V AC.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. Charging the Battery Pack       To charge the battery pack, connect the AC adapter to the computer and an electrical outlet. The Battery Charge Indicator ( ) on the computer glows amber to indicate that charging is in progress. You are advised to keep the computer power off while the battery is being charged. When the battery is fully charged, the Battery Charge Indicator lights green.
The charging times are as follows: Battery Type Charging Time Computer is Off Computer is On and in Idle State 6-cell (4 A) 2.5~3.5 hours 3.0~4.3 hours 9-cell (4 A) 3.5~4.5 hours 4.0~6.0 hours Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging. It can take several hours. 1. Make sure that the computer power is turned off. Connect the AC adapter to fully charge the battery pack. 2. After the battery pack is fully charged, turn on the computer. When the message “Click mouse or press <Enter> for Menu” appears, click the touchpad’s left button or press the Enter key to invoke the program. 3. A small window appears, select Launch System Setup. 4. Disconnect the AC adapter and leave the computer on until the battery is fully discharged. The computer will shut down automatically. 5. Connect the AC adapter to fully charge the battery pack.
Checking the Battery Level By Operating System You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the icon on the system tray. By Gas Gauge On the exterior side of the battery pack is a gas gauge for displaying the estimated battery charge. When the battery pack is not installed in the computer and you want to know the battery charge, you can press the switch with a pointed device to see the corresponding value of indicator segment that light green. The value of the corresponding green segment indicates the relative percentage of the battery charge. The battery pack is fully discharged when you see no segment glowing green. Switch
Replacing the Battery Pack   If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup. To replace the battery pack, follow these steps: 1. Make sure that the computer is not turned on or connected to AC power. 2. Locate the battery compartment on the left side of the computer. 3. Open the compartment cover by sliding the release latch to the left () then upwards (). 4. Pull on the ribbon strip to remove the battery pack.
5. Slide the new battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery pack removal). 6. Close the compartment cover and slide the release latch downward, then towards the right to secure the battery pack. Installing a Second Battery Pack (Optional) You can install a second battery pack to your computer for a longer operating time when AC power is not available. To install a second battery pack: 1. Make sure that system power is off. 2. Open the media bay cover by sliding the release latch towards the left. 3. Press upwards the optical drive release latch () and carefully pull on the ribbon strip () to remove the optical drive.
4. Slide the second battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery pack removal). 5. Close the media bay cover to secure the second battery pack.   On the exterior side of the second battery pack is a gas gauge for displaying the estimated battery charge. When the battery pack is not installed in the computer and you want to know the battery charge, you can press the switch with a pointed device to see the corresponding value of indicator segment that light green. The value of the corresponding green segment indicates the relative percentage of the battery charge. The battery pack is fully discharged when you see no segment glowing green.
Switch
Battery Low Signals and Actions The battery icon changes appearance to display the current state of the battery so that you can see how much charge remains (Windows default setting). When the battery charge is above 25 % the battery icon is green. When the battery charge reaches 25 % a yellow triangle with an exclamation point (!) appears above the green battery icon. When the charge reaches the low battery level a red circle with a white “X” appears above the green icon. The computer’s Battery Charge Indicator ( ) blinks red to alert you to take actions. Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer. If you are using the audio subsystem, ExpressCard, hard or USB flash disk, the battery might run out of charge very quickly. Always respond to Battery Low by placing your computer on Hibernation mode, turning off the computer, or connecting the AC adapter.  
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time. In general, Windows’ power management works in this way: What... When... Power to the hard disk is turned off When the hard disk has been idle for a set period. Power to the display is turned off When the display has been idle for a set period. The computer enters the Sleep mode. The hard disk and display are turned off and the entire system consumes less power. When the entire system has been idle for a set period. When you press the Fn+F12 hot key. * When you close the cover. * When you press the power button. * The computer enters the Hibernation mode. (See the next subsection for more information.) When you press the Fn+F12 hot key. * When you close the cover. * When you press the power button. * * Depends on your settings in Windows. For detailed information on power management, see Windows’ Help.
Hibernation Power Options  System SettingsControl Panel  Mobile PC Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the computer can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shuts down. The next time you turn on your computer, you return to exactly where you left off.
Power-Saving Tips Aside from enabling your computer’s power saving mode (see previous section), you can do your part to maximize the battery’s operating time by following these suggestions.  Press the power saving quick button ( ) to enter into power saving mode when using battery power.  Do not disable Power Management. Choose a Windows power plan that saves power. A power plan is a collection of hardware and system settings that control how your computer manages power.  Decrease the LCD brightness to the lowest comfortable level.  Shorten the length of time before Windows turn off the display.  Many USB devices use power just by being connected. If you use a USB mouse, you can save power by disconnecting the mouse and using the touchpad. If you use a USB flash drive, unplug it when you are not using it.  If you work with an application that uses a PC card, exit the application when you finish using it.  If you have a PC card installed, remove it when not in use. Some PC cards drain power even while they are inactive.  Deactivate the WLAN function if you are not using it (see Chapter 2).  Deactivate the Bluetooth feature if you are not using it (see Chapter 2).  Turn off the computer when you are not using it.
Chapter 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Slide the release latch towards the right to open the connector cover. 3. Plug the monitor’s D-type signal connector to the computer’s VGA connector. 4. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 5. To use the monitor, turn on the monitor before turning on the computer. 6. The monitor should respond by default. If not, you can switch the display to the monitor or to both (simultaneous display), or to multi-display by pressing the Fn+F5 hot key. In Windows, you can also change the display through the Display Settings Properties.
7. You can change display settings through your operating system. See your operating system documentation or online help for specific information.
Connecting a Serial Device Your computer has two serial ports for connecting a serial device such as a serial mouse or serial communication device (modem). Follow this procedure to connect a serial device: 1. Make sure the “Serial Port COM1/COM2” item is set properly in the BIOS Setup program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on 3. Slide the release latch towards the right to open the port cover. 4. Plug the device cable to the serial port on the rear of the computer. 5. Turn on the computer.
Connecting a USB Device Your computer has three USB ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. The USB ports support transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices. To connect a USB device, slide the release latch towards the right to open the port cover and then simply plug the device cable to one of the USB ports.
Connecting an IEEE 1394 Device Your computer has a mini IEEE 1394 port for connecting IEEE 1394 devices that include not only computer peripheral devices such as scanner, printer and high-quality CCD, but also consumer electronic equipment such as DVCAM and VCR. To connect an IEEE 1394 device, prepare an IEEE 1394 cable. Slide the release latch towards the right to open the connector cover. Then plug the appropriate end of the cable to the computer’s mini IEEE 1394 connector and the other end to the device’s corresponding connector.
Using Smart Cards (Optional) Depending on the model, your computer has a smart card slot for additional security feature, providing tamper-proof storage of user and account identity. A smart card is a type of plastic card embedded with a computer chip that stores and transacts data between you (user) and the computer. You need to install third-party smart card software to take advantage of the smart card feature. Inserting and Removing a Smart Card To insert a smart card: 1. Locate the smart card slot on the right of the computer and open the cover. 2. Slide the smart card, with its label and embedded computer chip facing down into the slot. 3. When a new card is seated, use the third-party smart card software to allow your computer to read it. To remove a smart card: 1. Make sure that the third-party smart card software is not accessing the smart card. 2. Pull the card out of the slot. Computer Chip
Using PC Cards Depending on your model, your computer has one or two PC card slots which supports type II card and CardBus specifications. Inserting and Removing a PC Card   To insert a PC card: 1. Locate the PC card slot(s) on the right side of the computer and open the cover. 2. Slide the PC card, with its label facing up, into the slot until the eject button pops out. 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. Eject button
To remove a PC card: 1. Double-click on the Safely Remove Hardware icon found on the Windows taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the PC card from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.
Using ExpressCards (Optional) Depending on the model, your computer has an ExpressCard slot. ExpressCard supports the PCI Express and USB 2.0 serial data interfaces (supporting speeds of up to 2.5 Gbps and 480 Mbps respectively), improving speed in data transfer while conserving power usage. ExpressCard Type The ExpressCard slot can accommodate a 54 mm (ExpressCard/54) or 34 mm (ExpressCard/34) wide ExpressCard. Typical ExpressCards support a very extensive range of applications including memory, wired and wireless communication cards, and security devices. Shown next are the appearances of ExpressCards for your reference. ExpressCard/54 ExpressCard/34
Inserting and Removing an ExpressCard To insert an ExpressCard: 1. Locate the ExpressCard slot on the right side of the computer and open the cover. 2. Slide the ExpressCard, with its label facing up, all the way into the slot until the rear connectors click into place. 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove an ExpressCard: 1. Double-click on the Safely Remove Hardware icon found on the Windows taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the ExpressCard from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.
Using the Card Reader   Your computer has a Card Reader. The Card Reader is a small drive for reading from and writing to removable storage cards (or called memory cards). The Card Reader supports the MultiMediaCard (MMC), Secure Digital (SD), Memory Stick (MS), and Memory Stick PRO (MS PRO) cards. Shown next are the appearance and size of each card type for your reference. Type MMC Card SD Card MS / MS PRO Card Appearance Size 24×32×1.4 (mm) 24×32×2.1 (mm) 21.5×50×2.8 (mm)
To insert a storage card: 1. Locate the Card Reader slot on the right side of the computer and open the cover. 2. Align the card with its connector pointing to the slot and its label facing up. Slide the card into the slot until it reaches the end. 3. Windows will detect the card and assign it a drive name. To remove a storage card: 1. Double-click My Computer. 2. Right-click the drive with the card and select Eject. 3. Pull the card out of the slot.
Using the Port Replicator (Optional) A port replicator is available as an option. This device eliminates the hassles of having you connect and disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector at the rear of your computer. 1. Slide open the expansion bus connector cover. 2. Connect your port replicator to the expansion bus connector ( ). For more detailed information, refer to the Operating Instructions of the port replicator.  
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 4 GB on the two 533/667 MHz DDRII SO-DIMM slots. To install the RAM module: 1. Remove the battery pack (see chapter 3) and make sure that the computer is not connected to AC power. 2. Carefully place the computer upside down. 3. Remove the six screws to open the compartment cover. 4. To install the RAM module, match the module's notched part with the socket's projected part and firmly insert the module into the socket at a
20-degree angle (). Then push down until the retaining clips lock the module into position (). 5. Close the compartment cover and secure with six screws.  
Chapter 5 Using BIOS Setup and System Recovery BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. System Recovery reinstalls Windows to your system and configures it to the system’s factory default settings. This chapter tells you how to use the BIOS Setup and System Recovery.
BIOS Setup When to Use You need to run BIOS Setup Utility when:  You see an error message on the screen requesting you to run BIOS Setup Utility.  You want to restore the factory default BIOS settings.  You want to modify some specific settings according to the hardware .  You want to modify some specific settings to optimize the system performance. Starting BIOS Setup    To run BIOS Setup Utility, press the Enter key or click the left touchpad button when the prompt appears on the screen during system startup. The prompt shows up on the screen for only a few seconds. You must press the Enter key or click the left touchpad button quickly. A small window appears, select Launch System Setup. The BIOS Setup Utility main screen appears as shown next.
The BIOS Setup Utility screen can be divided into four areas:  On the top is the menu bar containing the titles of the available menus. Each menu title brings a specific menu.  The left column of the menu displays the menu items.  The right column of the menu provides more detailed information when a menu item is highlighted.  The bottom of the menu provides keyboard instructions for moving around and making selections. Moving Around and Making Selections You must go through two or three levels to complete the setting for an item. In most cases, there are two levels: menu title and submenu. Use the keyboard to move around and make selections. Keyboard information can be found at the bottom of the screen. A brief description of keyboard usage is listed next:
Key Function  ,  Selects a menu title.  ,  Selects an item or option. + / – Changes the value. Enter 1) Brings up the sub-menu when available. 2) Opens or closes the option window when an item is selected. Esc 1) Exits BIOS Setup Utility. 2) Closes the option window if one is open. F1 Provides help information. F9 Loads setup defaults. F10 Saves and exit the BIOS Setup Utility. Information Menu The Information menu contains the basic configuration information of the system.
Main Menu The Main menu contains the system date and time, as well as USB and wireless LAN settings of the system. System Time sets the system time. System Date sets the system date. Legacy USB Support enables or disables the system’s support for Legacy USB device in DOS mode. Wireless LAN setting this item to Off will start the system with wireless radio off, On will start the system with the wireless radio on, and Last State will start the system based on the state of wireless radio during your last power off.
Advanced Menu The Advanced menu contains the advanced settings as shown next. P1 Function allows you to specify the P1 quick button function. When set at Blackout the P1 quick button allows you to turn off the LCD backlight and LED indicator. When set at Quick Btn the P1 quick button functions as a user customized quick launch key. CD/DVD Auto Power Control allows you to enable the optical drive’s automatic power control when using battery power. NIC Auto Power Control allows you to enable the NIC’s (network interface controller) automatic power control when using battery power. Azalia Modem PME Enable allows you to wake up the system via an Azalia modem. USB Wake-up From S3 allows the system to wake-up from Sleep mode via USB device. When set at Disabled only the power button can wake-up the system from Sleep mode. SATA HDD Mode when set at Compatible and connecting a SATA (serial ATA) hard drive is set as Primary on SATA controller in Legacy mode. When connecting a PATA (parallel ATA) hard drive is set as Secondary on SATA controller in Legacy mode.
When set at Enhanced and connecting a SATA hard drive is set as Primary on SATA controller in Native mode. When connecting a PATA hard drive is set as Primary on PATA controller in Legacy mode. AHCI Configuration enables support for AHCI (Advanced Host Controller Interface) Native command queuing and Link Power Management. Requires Windows XP Service Pack 1 + IAA driver or newer operating system. This item will not appear if the above item “SATA HDD Mode” is set at Compatible. Serial Port COM1 when enabled the serial port COM1 is configured at 3F8h, IRQ4. Serial Port COM2 when enabled the serial port COM2 is configured at 2F8h, IRQ3. Security Menu The Security menu contains the TPM (Trusted Platform Module) setting. TPM is a component on your computer’s mainboard that is specifically designed to enhance platform security above-and-beyond the capabilities of today’s software by providing a protected space for key operations and other security critical tasks. Using both hardware and software, TPM protects encryption and signature keys at their most vulnerable stages – operations when the keys are being used unencrypted in plain-text form. TPM is specifically designed to shield unencrypted keys and platform authentication information from software-based attacks.
Upon pressing Enter, the following screen appears. TPM Support enables or disables TPM support (see chapter 6 for details). Current TPM State shows the current TPM state. Change TPM State allows you to select between No Change, Clear, Deactivate & Disable, and Enable & Activate.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a device from which to load the OS. Below is a brief description of keyboard usage: Key Function  ,  Selects (highlight) a boot device. +, – Changes the boot sequence. 1 to 4 Loads the default boot sequence. f or r Specifies if the boot device is fixed (f) or removable (r). X Moves the highlighted boot device from the “Boot priority order” list to the “Excluded from boot order” list, and vice versa. Shift+1Deactivates/activates the highlighted boot device on the “Boot priority order” list. When a device has been deactivated, an “ ” (exclamation) symbol appears beside the item and system will bypass it when detecting boot device during POST.
Exit Menu The Exit menu displays ways of exiting BIOS Setup Utility. After finishing with your settings, you must save and exit so that the changes can take effect. Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility. Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made. Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items. Saves Changes saves the changes you have made.
System Recovery You need to run System Recovery when:  Your computer does not start correctly.  Your Windows operating system does not start at all.  You want to restore the factory default Windows settings. To run System Recovery: 1. During system startup when the following screen appears, press Ctrl + Alt + F2 keys for four seconds or press Enter and select HDI Recovery when a small window appears on the screen. 2. The message This will help you reinstall Windows to the whole HDD to factory default. All data on HDD will be lost appears on the screen
to ask if you want to access System Recovery. Type 1 to continue or type 0 to exit. 3. A warning message appears as follows: **************************************** You must accept the following terms before performing the recovery process: 1. The recovery software is solely the purpose of reinstalling or restoring software associated with the hard disk of this operating GETAC machine. 2. Except the above, no other use is granted hereunder. **************************************** (1)Yes, I agree to the provisions of this agreement and wish to continue. (0)No, I do not agree to the provisions of this agreement and do not wish to continue. Type 1 to continue. 4. Type 1 again when the message Are you sure you want to recover now? (1)Yes (0)No appears onscreen. The following screen appears: 5. Your system will start the recovery process and Windows operating system will be re-installed to its default setting.
Chapter 6 Using the TPM and P1 Utility Your computer comes with an added security feature known as the TPM (Trusted Platform Module) – a component on your computer’s mainboard that is specifically designed to enhance platform security above-and-beyond the capabilities of today’s software by providing a protected space for key operations and other security critical tasks. Also, located on top of your keyboard is the P1 quick launch key. The quick launch key utility allows you to re-define (customize) the P1 quick launch key according to your needs. This chapter describes how to use these utilities.
Using TPM (Trusted Platform Module) TPM is a hardware-based security feature that can be used to create and manage computer-generated digital certificates. When combined with security software, the TPM enhances existing network and computer security by enabling features such as file protection capabilities and protected e-mail.  TPM Support Security  Change TPM StateSecurity You can use the certificates to:  Send and receive secure email from email clients like Microsoft Windows Mail/Outlook Express, Microsoft Outlook or Netscape Messenger  Set up browser (e.g. Netscape Navigator or Internet Explorer) and web server (e.g. Microsoft Internet Information Server) for Client Authentication  Sign Microsoft Word macros  Encrypt files and folders  Secure network connections Start  All Programs  Infineon Security Platform Solution  Help
P1 Quick Launch Key Utility If you select Quick Btn in BIOS Setup program on the P1 Function item under the Advanced menu (see chapter 5 for details), you can use the quick launch key utility that allows you to define the P1 quick launch key. To start the utility, right-click the GETAC utility icon ( ) and select Quick Buttons Definition on the Windows system tray. The Quick Button Definition window appears as shown next. Defining the buttons: The box in the window represents the user-definable button. To assign a program to a button, click the Open icon to pop up the Select a File to Open dialog box as shown next and select the desired program. Then, click Open to complete the process. Box Cancel Open
The appropriate icon will then appear in the box. To launch the program, press the P1 quick launch key, or, if the Quick Button Definition window is open, click the box containing the icon.
Chapter 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer. This chapter gives you guidelines covering areas such as protecting, storing, cleaning, and traveling.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Windows Security Center Windows Security Center protects your computer against intrusion.
Windows Security Center alerts you to take action on the following security essentials:  Windows Firewall  Windows Update  Malware Protection (anti-virus, anti-spyware)  Others (Internet security, user account control) For detailed information on Windows Security Center, see Windows’ Help. Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores. To use the lock, loop the lock cable around a stationary object such as a table. Insert the lock to the Kensington lock hole and turn the key to secure the lock. Store the key in a safe place.
Taking Care of the Computer Location Guidelines  For optimal performance, use the computer where the recommended temperature is between 0 C (32 F) and 55 C (131 F) – actual operating temperature depending on product specifications.  Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust.  Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface. Otherwise, overheating may occur that results in damage to the computer.  Keep the computer at least 13 cm (5 inches) away from electrical appliances that can generate a strong magnetic field such as a TV, refrigerator, motor, or a large audio speaker.  Avoid moving the computer abruptly from a cold to a warm place. A temperature difference of more than 10 C (18 F) may cause condensation inside the unit, which may damage the storage media.  Do not place the computer on an unsteady surface. General Guidelines  Do not place heavy objects on top of the computer when it is closed as this may damage the display.  The screen surface is easily scratched. Do not use paper towels to clean the display but use the included soft cloth. Avoid touching it with your fingers, pen, or pencil.  To maximize the life of the backlight in the display, allow the backlight to automatically turn off as a result of power management. Avoid using
a screen saver or other software that prevents the power management from working. Cleaning Guidelines  Never clean the computer with its power on.  Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer.  Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display.  Dust or grease on the touchpad can affect its sensitivity. Clean the pad by using adhesive tape to remove the dust and grease on its surface. Battery Pack Guidelines  Recharge the battery pack when it is nearly discharged. When recharging, make sure that the battery pack is fully charged. Doing so may avoid harm to the battery pack.  The battery pack is a consumable product and the following conditions will shorten its life: – when frequently charging the battery pack – when using, charging, or storing the battery in high temperature condition  To avoid hastening the deterioration of the battery pack thereby prolonging its useful life, minimize the number of times you charge it so as not to frequently increase its internal temperature.  Charge the battery pack between 10 C ~ 30 C (50 F ~ 86 F) temperature range. A higher environment temperature will cause the battery pack’s temperature to rise. Avoid charging the battery pack inside a closed vehicle and in hot weather condition. Also, charging will not start if the battery pack is not within the allowed temperature range.
 It is recommended that you do not charge the battery pack more than once a day.  It is recommended that you charge the battery pack with the computer’s power off.  To maintain the battery pack’s operating efficiency, store it in a cool dark place removed from the computer and with 30 % ~ 40 % charge remaining.  Important guidelines when using the battery pack. When installing or removing the battery pack take note of the following: – avoid installing or removing the battery pack when the computer is in Sleep mode. Abruptly removing the battery pack may cause loss of data or the computer may become unstable. – avoid touching the battery pack terminals or damage may occur, thereby causing improper operation to it or the computer. The computer’s input voltage and surrounding temperature will directly affect the battery pack’s charge and discharge time: – charging time will be prolonged when the computer is turned on. To shorten the charging time, it is recommended that you place the computer in sleep or hibernation mode. – a low temperature will prolong the charging time as well as hasten the discharge time. Touchscreen Guidelines  Use the finger or the included touchscreen pen on the display. Using a sharp or metallic object other than your finger or touchscreen pen may cause scratches and damage the display, thereby causing errors.  Avoid using excessive force that may cause damage to the display.  Use a soft cloth to remove dirt on the display. The touchscreen surface has a special protective coating that prevents dirt from sticking to it. Not using a soft cloth may cause damage to the special protective coating on the touchscreen surface.
To remove hard to remove dirt, blow some steam on the particular area and gently wipe away using a soft cloth.  Turn off the computer power when cleaning the display. Cleaning the display with the power on may cause improper operation.  Use the touchscreen within the intended area only. The display area and touchscreen operating area is the same. Using it beyond the allowed area may cause damage to the display and result in improper operation.  Do not use excessive force on the display. Avoid moving the computer while holding the display or twisting the display. Avoid placing objects on top of the display as this may cause the glass to break thereby damaging the display.  Using the touchscreen during low temperature (less than 5 oC) may cause a slower response time, this is normal. A normal response time may be restored upon returning to room temperature.  When there is noticeable discrepancy in the operation of the touchscreen function (wrong location on intended operation or improper display resolution), refer to the Windows online Help for instructions on recalibrating the touchscreen display.
When Traveling  Before traveling with your computer, make a backup of your hard disk data into flash disks or other storage devices. As an added precaution, bring along an extra copy of your important data.  Make sure that the battery pack is fully charged.  Make sure that the computer is turned off and the top cover is securely closed.  Make sure that all the connector covers are closed completely to ensure the waterproof integrity.  Do not leave objects in between the keyboard and closed display.  Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger.  Hand-carry the computer. Do not check it in as luggage.  If you need to leave the computer in the car, put it in the trunk of the car to avoid exposing the computer to excessive heat.  When going through airport security, it is recommended that you send the computer and flash disks through the X-ray machine (the device you set your bags on). Avoid the magnetic detector (the device you walk through) or the magnetic wand (the handheld device used by security personnel).  If you plan to travel abroad with your computer, consult your dealer for the appropriate AC power cord for use in your country of destination.
Chapter 8 Troubleshooting Computer problems can be caused by hardware, software, or both. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem:  Try to isolate which part of the computer is causing the problem.  Make sure that you turn on all peripheral devices before turning on the computer.  If an external device has a problem, make sure that the cable connections are correct and secure.  Make sure that the configuration information is properly set in the BIOS Setup program.  Make sure that all the device drivers are correctly installed.  Make notes of your observations. Are there any messages on the screen? Do any indicators light? Do you hear any beeps? Detailed descriptions are useful to the service personnel when you need to consult one for assistance. If any problem persists after you follow the instructions in this chapter, contact an authorized dealer for help.
Solving Common Problems Battery Problems The battery does not charge (Battery Charge indicator does not light amber).  Make sure that the AC adapter is properly connected.  Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature.  Make sure that the battery pack is installed correctly.  Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.  If you often partially recharge and discharge, the battery might not be charged to its full potential. Initialize the battery to solve the problem. (See “Initializing the Battery Pack” in Chapter 3 for instructions.) The battery operating time indicated by the battery meter does not match the actual operating time.  The actual operating time can be different from the estimated time, depending on how you are using the computer. If the actual operating time is much less than the estimated time, initialize the battery. (See “Initializing the Battery Pack” in Chapter 3 for instructions.) Bluetooth Wireless Transmission Problems I cannot connect to another device with Bluetooth wireless technology.  Make sure that the Bluetooth wireless card is correctly installed.  Make sure that both devices have activated Bluetooth feature.
 Make sure that the distance between the two devices are not over 10 meters or that there are no walls or other obstructions between the devices.  Make sure that the other device is not in “Hidden” mode.  Make sure that both devices are compatible. Display Problems Nothing appears on the screen.  During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back.  The brightness level might be too low. Increase brightness by pressing the Fn+F7 hot key.  The display output might be set to an external device. To switch the display back to the LCD, press the Fn+F5 hot key or change the display through the Display Settings Properties. The characters on the screen are dim.  Adjust the brightness and/or contrast. Bad dots appear on the display at all times.  A small number of missing, discolored, or bright dots on the screen are an intrinsic characteristic of TFT LCD technology. It is not regarded as a LCD defect. The external monitor displays nothing.  Make sure that the monitor is turned on.  Make sure that the monitor’s signal cable is properly connected.  Switch the display to the monitor by pressing the Fn+F5 hot key or change the display through the Display Settings Properties. Simultaneous display/multi-display does not work.  Make sure that you turn on the external monitor before turning on the computer.
 Press the Fn+F5 hot key to toggle through the display options or change the Display Settings Properties in Windows. ExpressCard Problems The ExpressCard does not work.  Make sure that the ExpressCard is correctly seated.  If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. The ExpressCard stops communicating properly.  The application may have been reset when the computer is turned off or in Sleep mode. Exit and restart the application. Hardware Device Problems The computer does not recognize a newly installed device.  The device may not be correctly configured in the BIOS Setup program. Run the BIOS Setup program to identify the new type.  Make sure if any device driver needs to be installed. (Refer to the documentation that came with the device.)  Make sure if the device needs any jumper or switch settings. (Refer to the documentation that came with the device.)  Check the cables or power cords for correct connections.  For an external device that has its own power switch, make sure that the power is turned on. Hard Disk Drive Problems The hard disk drive error message appears on the screen.  The hard disk drive has defects. Ask your dealer for help.
The hard disk drive operations seem slow.  The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. The hard disk drive in-use indicator glows without blinking.  The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. Keyboard, Mouse, and Touchpad Problems The keyboard does not respond.  Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled.  Make sure that the Num Lock is switched on. (Check if the Num Lock Indicator glows or not.) The external keyboard does not work.  Make sure that the keyboard cable is properly connected. The USB mouse does not work.  Make sure that the mouse cable is properly connected. The touchpad does not work, or the pointer is difficult to control with the touchpad.  Make sure that the touchpad is clean. LAN Problems I cannot access the network.  Make sure that the LAN cable is properly connected to the RJ-45 connector and the network hub.  Make sure that the network configuration is appropriate.
 Make sure that the user name or password is correct. WLAN Problems I cannot use the WLAN feature.  Make sure that the mini PCI-E WLAN card is correctly installed.  Make sure that the WLAN feature is turned on. Transmission quality is poor.  Your computer may be in an out-of-range situation. Move your computer closer to the Access Point or another WLAN device it is associated with.  Check if there is high interference around the environment and solve the problem as described next. Radio interference exists.  Move your computer away from the device causing the radio interference such as microwave oven and large metal objects.  Plug your computer into an outlet on a different branch circuit from that used by the affecting device.  Consult your dealer or an experienced radio technician for help. I cannot connect to another WLAN device.  Make sure that the WLAN feature is turned on.  Make sure that the SSID setting is the same for every WLAN device in the network.  Your computer is not recognizing changes. Restart the computer.  Make sure that the IP address or subnet mask setting is correct. I cannot communicate with the computer in the network when Infrastructure mode is configured.  Make sure that the Access Point your computer is associated with is powered on and all the LEDs are working properly.
 If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel.  Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with.  Make sure that your computer is configured with the same security option (encryption) to the Access Point.  Use the Web Manager/Telnet of the Access Point to check whether it is connected to the network.  Reconfigure and reset the Access Point. I cannot access the network.  Make sure that the network configuration is appropriate.  Make sure that the user name or password is correct.  You have moved out of range of the network.  Turn off power management. Modem Problems The modem does not work.  Make sure that the telephone line is properly connected.  Make sure that the COM port in the communication software is correctly set.  Turn off power management. Optical Drive Problems The optical drive cannot read a disc.  Make sure that the disc is correctly seated in the tray, with the label facing up.
 Make sure that the disc is not dirty. Clean the disc with a disc cleaning kit, available in most computer stores.  Make sure that the computer supports the disc or the files contained. You cannot eject a disc. The disc is not properly seated in the drive. Manually release the disc following the method described next: 1. Turn off the computer. 2. Open the media bay cover by sliding the release latch towards the left. 3. Insert a small rod, such as a straightened paperclip, into the drive’s manual eject hole and push firmly to release the tray. 4. Pull the tray out until fully extended, and then remove the disc. PC Card Problems The PC card does not work.  Make sure that the PC card is correctly seated.
 If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. The PC card stops communicating properly.  The application may have been reset when the computer is turned off or in Sleep mode. Exit and restart the application. Power Management Problems The computer does not enter Sleep or Hibernation mode automatically.  If you have a connection to another computer, the computer does not enter Sleep or Hibernation mode if the connection is actively in use.  Make sure that the Sleep or Hibernation time-out is enabled. The computer does not enter Sleep or Hibernation mode immediately.  If the computer is performing an operation, it normally waits for the operation to finish. The computer does not resume from Sleep or Hibernation mode.  The computer automatically enters Sleep or Hibernation mode when the battery pack is empty. Do any one of the following:  Connect the AC adapter to the computer.  Replace the empty battery pack with a fully charged one. The computer does not enter Hibernation mode with the Fn+F12 hot keys.  Make sure that the Hibernation function is specified for the sleep button.  You might be using a PC card that prevents the computer from entering Hibernation mode. To enter the mode, stop the communication program and then remove the card or stop the card.
Software Problems An application program does not work correctly.  Make sure that the software is correctly installed.  If an error message appears on the screen, consult the software program’s documentation for further information.  If you are sure the operation has stop, reset the computer. (See “Resetting the Computer” later in this chapter.) Sound Problems No sound is produced.  Make sure that the volume control is not set too low.  Make sure that the computer is not in Sleep mode.  If using an external speaker, make sure that the speaker is properly connected. Distorted sound is produced.  Make sure that the volume control is not set too high or too low. In most cases, a high setting can cause the audio electronics to distort the sound. The sound system does not record.  Adjust the playback or recording sound levels. The external microphone or audio device does not work.  Make sure that the microphone is connected to the proper connector on the computer.  Click the speaker symbol on the taskbar and check the Windows volume control.  Check the volume control of your computer.
Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green.  If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly.  If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST.  Restart your computer. Other Problems The date/time is incorrect.  Correct the date and time via the operating system or BIOS Setup program.  After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life. Call an authorized dealer to replace the RTC battery.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the computer operation seems to hang up, first wait. It is possible that the computer is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard. If you are sure the operation has stopped and you cannot use the “restart” function of the operating system, reset the computer. Reset the computer by any one of these methods:  Press Ctrl+Alt+Del on your built-in keyboard.  If the above action does not work, turn off the computer with the power button. Wait for at least five seconds and turn it on again.
Appendix A Specifications Parts Specifications CPU Intel® Core™ 2 Duo Merom processor LV L7300/LV7500 800 MHz FSB (Front Side Bus), 1.4/1.6 GHz, 4 MB L2 cache thermal specifications 17 W Chipset NorthBridge Intel® GM965, dual channel support SouthBridge Intel® ICH8M BIOS 1 MB EEPROM, ACPI, fingerprint / smart card security, TPM RAM (system) Up to 4 GB DDRII 533/667 MHz, 2 × 200-pin SO-DIMM sockets 1.25-inch height Display Panel 13.3-inch (4:3) wide TFT LCD, resolution up to 1024×768 XGA with touchscreen (option), or with sunlight-readable and touchscreen 1200 nits (option) Video controller UMA VRAM Up to 384 MB (depends on BIOS setting) Video port Analog VGA Audio Features Azalia interface, 2 channel analog output, internal microphone Speaker 1.5 watt (8 ohm) stereo × 2 Ports Two audio ports for Line-out (green color) / Mic-in (pink color) Keyboard Standard keys with numeric pad keys, 12 function keys, special Fn (Function) key and Windows keys with water-proof membrane or backlight (option) Pointing device Glide touchpad with 2 buttons, scroll bar Storage device Hard disk drive SATA interface, 2.5-inch diameter (9.5 mm height), 5400 rpm support, G-sensor, shock-mounted, user-removable, solid-state disk (option), automotive hard disk drive (option), low temperature – 4 oF (– 20 oC) up to 131 oF (55 oC) (option) Optical drive DVD Combo / DVD Dual / Super-Multi
Parts Specifications Card slots Card Reader 4-in-1 (MMC/SD/MS/MS PRO card) module PCMCIA CardBus Type II × 2 or 1 with any of the following: ExpressCard/34 / ExpressCard/54 support, or Smart Card I/O ports USB ports × 3 (USB 2.0 support), serial port × 2 (RS-232), RJ-45 port, RJ-11 port, mini IEEE 1394a port, expansion bus connector Modem Azalia interface, 56 Kbps, V.90 MDC 1.5 internal fax modem LAN 10/100/1000 Mbps Wireless LAN One mini PCI-E slot for wireless LAN card, compliant with IEEE 802.11a/b/g/n, on/off slide switch Bluetooth wireless technology Specification 2.0 module, on/off slide switch GPS (option) GPS module 3G (option) CDMA EVDO, external accessible SIM card slot Security Kensington lock TPM 1.2 Fingerprint sensor Smart Card Reader (integrated) will occupy Type II PCMCIA slot – option Power AC adapter Universal AC adapter 90 W; input: 100240 V, output: 19 V Primary battery Li-ion smart battery 9-cell 7650 mAH / 11.1 V or above Secondary battery Li-ion smart battery 9-cell 7650 mAH / 11.1 V or above Dimension (W×D) 303.5×298×60 mm (11.9×11.7×2.36 inch) with handle Weight 3.5 kg (7.7 lb)
Appendix B Regulatory Information This appendix provides regulatory statements and safety notices on your computer.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Please note: The use of a non-shielded interface cable with this equipment is prohibited.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. Safety Notices About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. SWEDISH VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.
FINNISH VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäß em Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. FRENCH ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Attention (for USA Users) The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. About the AC Adapter  Use only the AC adapter supplied with your computer. Use of another type of AC adapter will result in malfunction and/or danger.  Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet are wet.  Allow adequate ventilation around the adapter when using it to operate the device or charge the battery. Do not cover the AC adapter with
paper or other objects that will reduce cooling. Do not use the AC adapter while it is inside a carrying case.  Connect the adapter to a proper power source. The voltage requirements are found on the product case and/or packaging.  Do not use the adapter if the cord becomes damaged.  Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. About the Modem Caution  Never install telephone wiring during a lightning storm.  Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.  Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.  Use caution when installing or modifying telephone lines.  Avoid using the telephone function (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.  Do not use the telephone function to report a gas leak in the vicinity of the leak.  Do not use this product near water, for example near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Caution (for USA Users) To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. The FCC limits are designed to provide reasonable protection against harmful interference when the equipment is installed and used in accordance with the instruction manual and operated in a commercial environment. However, there is no guarantee that interference will not occur in a particular commercial installation, or if operated in a residential area. If harmful interference with radio or television reception occurs when the device is turned on, the user must correct the situation at the user’s own expense. The user is encouraged to try one or more of the following corrective measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. CAUTION: The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by the manufacturer could void the user’s authority to operate this device. Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum
shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence. European Union CE Marking and Compliance Notices Statements of Compliance English This product follows the provisions of the European Directive 1999/5/EC. Danish Dette produkt er i overensstemmelse med det europæ iske direktiv 1999/5/EC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 1999/5/EC. Finnish Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä. French Ce produit est conforme aux exigences de la Directive Européenne 1999/5/EC. German Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 1999/5/EC. Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC.
Icelandic Þessi vara stenst reglugerð Evró pska Efnahags Bandalagsins nú mer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC. Swedish Denna produkt har tillverkats i enlighet med EG-direktiv 1999/5/EC. Local Restrictions of 802.11a/g/n Radio Usage CAUTION: Due to the fact that the frequencies used by 802.11a/g/n wireless LAN devices may not yet be harmonized in all countries, 802.11a/g/n products are designed for use only in specific countries or regions, and is not allowed to be operated in countries or regions other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries or regions for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country or region of use. Any deviation from permissible settings and restrictions in the country or region of use could be an infringement of local law and may be punished as such. The European variant is intended for use throughout the European Economic Area. However, authorization for use is further restricted in particular countries or regions within countries, as follows: General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz.
Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors. See the instructions next under the heading “Turning Off the Wireless LAN Radio.” France Departments in Which the Wireless LAN Module Can Be Used (Indoors Only) The wireless LAN module can currently be used indoors only in the following 38 departments of mainland France. Please turn off your wireless LAN radio when operating the device in areas/places other than the 38 departments listed: 01 Ain Orientales 36 Indre 66 Pyrénées 02 Aisne 37 Indre et Loire 67 Bas Rhin 03 Allier 41 Loir et Cher 68 Haut Rhin 05 Hautes Alpes 42 Loire 70 Haute Saône 08 Ardennes 45 Loiret 71 Saône et Loire 09 Ariège 50 Manche 75 Paris 11 Aude 55 Meuse 82 Tarn et Garonne 12 Aveyron 58 Nièvre 84 Vaucluse 16 Charente 59 Nord 88 Vosges 24 Dordogne 60 Oise 89 Yonne 25 Doubs 61 Orne 90 Territoire de Belfort 26 Drôme 63 Puy du Dôme 94 Val de Marne 32 Gers 64 Pyrénées Atlantique Departments in Which the Wireless LAN Module’s Maximum EIRP Not Shown in the Previous Table
Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements. While operating the computer in those French departments that do not allow use of the wireless LAN equipment, the user of the equipment must turn off the wireless LAN radio in order to comply with local regulations (see Chapter 2 for more information).

Navigation menu