Getac Technology 9213H Bluetooth for NoteBook PC User Manual 9213 User s Manual

Download:
Mirror Download [FCC.gov]
Document ID	1020145
Application ID	sst/tKoMzVqd7+f7BluwQg==
Document Description	User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	122.85kB (1535665 bits)
Date Submitted	2008-10-23 00:00:00
Date Available	2008-10-23 00:00:00
Creation Date	2008-09-26 10:03:08
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2008-09-26 10:07:13
Document Title	Microsoft Word - 9213 User's Manual.DOC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	kety_h

Hibernation
NOTE: Make sure that the hibernation feature is enabled in the “When I press the
power button,” “When I press the sleep button,” and “When I close the lid” of the Power
Options System Settings Properties from the Control Panel Mobile PC.
Hibernation is a very useful feature. People frequently open many
applications when they use computers. It takes some time to get all these
applications open and running, and normally they all have to be closed
before the computer can be turned off.
When you use the hibernation feature, you do not have to close the
applications. The computer stores the state of your computer to a file on
the hard disk and then shuts down. The next time you turn on your
computer, you return to exactly where you left off.
Managing Power
3-11
Power-Saving Tips
Aside from enabling your computer’s power saving mode (see previous
section), you can do your part to maximize the battery’s operating time by
following these suggestions.
Do not disable Power Management. Choose a power plan that saves
power. A power plan is a collection of hardware and system settings
that control how your computer manages power.
Decrease the LCD brightness to the lowest comfortable level.
Shorten the length of time before Windows turn off the display.
Many USB devices use power just by being connected. If you use a
USB mouse, you can save power by disconnecting the mouse and
using the touchpad. If you use a USB flash drive, unplug it when you
are not using it.
If you work with an application that uses an ExpressCard, exit the
application when you finish using it.
If you have an ExpressCard installed, remove it when not in use.
Some ExpressCards drain power even while they are inactive.
Deactivate the wireless LAN function if you are not using it.
(See Chapter 2.)
Deactivate the Bluetooth® wireless function if you are not using it.
(See Chapter 2.)
Turn off the computer when you are not using it.
3-12
Managing Power
Chapter 4
CHAPTER
Expanding Your Computer
You can expand the capabilities of your computer by connecting other
peripheral devices. When using a device, be sure to read the instructions
accompanying the device together with the relevant section in this
chapter.
This chapter gives guidelines on installing and using these devices:
External monitor
USB device
ExpressCard
Card Reader
Port Replicator
System memory
Expanding Your Computer
4-1
Connecting an External Monitor
If you want the benefits of a larger display screen with higher resolution,
you can connect an external CRT monitor or LCD monitor to your
computer. Follow this procedure to connect an external monitor:
1. Make sure that the computer is not turned on.
2. Plug the monitor’s signal connector to the computer’s VGA
connector.
3. Plug one end of the monitor’s power cord into the power socket on
the monitor and the other end to an electrical outlet.
4. To use the monitor, turn on the monitor before turning on the
computer.
5. The monitor should respond by default. If not, you can switch the
display to the monitor or to both (simultaneous display), or to
multi-display by pressing the Fn+F5 hot key. You can also change the
display through the Display Settings Properties.
6. You can change display settings through your operating system. See
your operating system documentation or online help for specific
information.
CAUTION: Do not disconnect the external monitor while the computer is in the Sleep
mode or Hibernation mode. If no external monitor is connected when the computer
resumes, the LCD might not display properly.
4-2
Expanding Your Computer
Connecting a USB Device
Your computer has three USB ports for connecting USB devices, such as
a digital camera, scanner, printer, modem, and mouse.
The USB ports support transfer rates up to 12 MB/s for USB 1.1 devices
and 480 MB/s for USB 2.0 devices.
To connect a USB device, simply plug the device cable to one of the USB
ports.
Expanding Your Computer
4-3
Using ExpressCards
NOTE: The ExpressCard interface is not compatible with the PC card interface. You
need optional adapters for using PC cards on your computer.
Your computer has an ExpressCard slot.
ExpressCard supports the PCI Express and USB 2.0 serial data interfaces
(supporting speeds of up to 2.5 Gbps and 480 Mbps respectively),
improving speed in data transfer while conserving power usage.
ExpressCard Type
The ExpressCard slot can accommodate a 34 mm (ExpressCard/34) wide
ExpressCard. Typical ExpressCards support a very extensive range of
applications including memory, wired and wireless communication cards,
and security devices.
Shown next is the appearance of ExpressCard/34 for your reference.
Inserting and Removing an ExpressCard
To insert an ExpressCard:
1. Locate the ExpressCard slot on the computer.
4-4
Expanding Your Computer
2. Press the cover tray ( ) and pull it out ( ).
3. Slide the ExpressCard, with its label facing up, all the way into the
slot until the rear connectors click into place.
4. When a new card is seated, the computer will detect it and try to install
the appropriate driver. Follow the on-screen instructions to complete
the process.
To remove an ExpressCard:
found on the
1. Double-click the Safely Remove Hardware icon
Windows system tray and the Safely Remove Hardware window
appears on screen.
2. Select (highlight) the ExpressCard from the list to disable the card.
3. Push the ExpressCard slightly to release the card.
4. Pull the card out of the slot.
Expanding Your Computer
4-5
Using the Card Reader
NOTE:
To take advantage of the Card Reader, the Card Reader driver supplied with your
computer must be installed. (See chapter 6 for details.)
If your hard disk is divided into several drives, make sure that all drives have been
formatted before using the Card Reader. Otherwise, you may encounter problems
when using the Card Reader.
You can use only storage cards. Your Card Reader does not support cards with I/O
(input/output) functions such as a wireless network card or Bluetooth card.
Your computer has a Card Reader. The Card Reader is a small drive for
reading from and writing to removable storage cards (or called memory
cards). The Card Reader supports the MultiMediaCard (MMC), Secure
Digital (SD), Memory Stick (MS) and Memory Stick PRO (MS PRO)
cards.
Shown next are the appearance and size of each card type for your
reference.
Type
MMC Card
SD Card
MS/MS PRO Card
24×32×1.4
(mm)
24×32×2.1
(mm)
21.5×50×2.8
(mm)
Appearance
Size
4-6
Expanding Your Computer
To insert a storage card:
1.
Locate the Card Reader slot on the front of the computer and remove
the slot cover.
2.
Align the card with its connector pointing to the slot and its label
facing up. Slide the card into the slot until it reaches the end.
3. Windows will detect the card and assign it a drive name (typically E).
To remove a storage card:
1. Click Start, then Computer.
2. Right-click the drive with the card and select Safely Remove.
3. Pull the card out of the slot.
Expanding Your Computer
4-7
Using the Port Replicator (Optional)
A port replicator is available as an option. This device eliminates the
hassles of having you connect and disconnect the various cables when
carrying your computer around and allows a variety of peripherals to be
connected including a headphone or microphone, etc.
The following table shows the external components of the port replicator
and briefly describes the function of each component.
NOTE: Depending on the model you purchased, the appearance of your port replicator
may not be exactly the same as those shown in this manual.
Front Components
Ref
4-8
Component
Description
Expansion Bus
Connector
Connects to the computer via a port replicator cable.
USB Port
Connects a USB device, such as a flash disk, printer,
digital camera, joystick, and more.
Headphone
Connector
Connects a set of headphones, external speakers with
amplifier, or an audio recording device.
Microphone-in
Connector
Connects an external microphone.
Expanding Your Computer
Rear Components
Ref
Component
Description
USB Ports
Each of the two ports connects a USB device, such as a
flash disk, printer, digital camera, joystick, and more.
DVI-D Connector
Connects an external LCD monitor or digital CRT
monitor.
RJ-45 Connector
Connects the LAN cable.
Power Connector
Connects the AC adapter.
To start using the port replicator:
1.
Connect one end of the port replicator cable to the expansion bus
connector ( ) on the left side of your computer and the other end to
the port replicator ( ).
2.
Plug the DC cord of the AC adapter to the power connector on the
port replicator ( ).
Expanding Your Computer
4-9
3.
Plug the female end of the AC power cord to the AC adapter and the
male end to an electrical outlet ( ).
4. When the AC adapter is connected, power is being supplied from the
electrical outlet to the AC adapter and onto your port replicator. Now,
you are ready to connect various devices to your port replicator.
CAUTION:
When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the port replicator. A reverse procedure may damage the AC adapter or
the port replicator.
When unplugging the connector, always hold the plug head. Never pull on the cord.
4-10
Expanding Your Computer
The following table shows the behavior of the computer’s I/O (input/
output) ports when connecting various devices to the I/O ports on the port
replicator.
Component
USB Ports
Behavior of computer’s I/O ports
All three ports on the computer and all three ports on the port
replicator can be used at the same time.
Power Connector The AC adapter on the computer supplies power to the computer
while the AC adapter on the port replicator supplies power to the
port replicator.
RJ-45 Connector The system will automatically detect whether the LAN cable
was first connected to the computer or port replicator and will
use it.
DVI-D
Connector
Display output to the computer’s VGA port will be disabled.
Audio Output
Connector
The computer’s audio output connector will be disabled.
Microphone
Connector
The computer’s microphone connector will be disabled.
NOTE: The computer’s S/PDIF connector will also be disabled when the port replicator
is connected.
Expanding Your Computer
4-11
System Memory Upgrade
You can upgrade your computer by changing system memory to a
maximum of 3 GB on the 800 MHz DDR2 SO-DIMM slot.
CAUTION: RAM modules are extremely sensitive to static electricity. There are cases
where static electricity generated by the human body has adversely affected such
modules. When inserting or removing a RAM module, do not touch the terminals or
internal components, insert objects other than the module, or allow foreign particles to
enter. Doing so has been known to cause damage, fire, or electrical shock.
To install the RAM module:
1.
Remove the battery pack (see chapter 3) and make sure that the
computer is not connected to AC power.
2. Carefully place the notebook computer upside down.
3. Remove the two screws to open the compartment cover.
4-12
Expanding Your Computer
4. To install the RAM module, match the module's notched part with the
socket's projected part and firmly insert the module into the socket at
a 20-degree angle ( ). Then push down until the retaining clips lock
the module into position ( ).
CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force
it. Check once more to ensure that the module is positioned correctly.
5. Close the compartment cover and secure with two screws.
Expanding Your Computer
4-13
Chapter 5
CHAPTER
Using BIOS Setup
BIOS Setup Utility is a program for configuring the BIOS (Basic Input/
Output System) settings of the computer.
BIOS is a layer of software, called firmware, that translates instructions
from other layers of software into instructions that the computer hardware
can understand. The BIOS settings are needed by your computer to
identify the types of installed devices and establish special features.
This chapter tells you how to use the BIOS Setup program.
Using BIOS Setup
5-1
When and How to Use BIOS Setup
When to Use
You need to run BIOS Setup Utility when:
You see an error message on the screen requesting you to run BIOS
Setup Utility.
You want to restore the factory default settings.
You want to modify some specific settings according to the hardware.
You want to modify some specific settings to optimize the system
performance.
Starting BIOS Setup
NOTE:
The BIOS Setup Utility screens shown in this chapter are for your reference only.
The actual items or settings on your computer may differ.
The BIOS Setup Utility program may have been updated after the publication of this
manual.
The settings you select in your operating system might override similar settings in
BIOS Setup Utility.
To run BIOS Setup Utility, press the F2 key when the prompt appears on
the screen during system startup. The prompt shows up on the screen for
only a few seconds. You must press the F2 key quickly. The BIOS Setup
Utility main screen appears as shown next.
5-2
Using BIOS Setup
The BIOS Setup Utility screen can be divided into three areas:
On the top is the menu bar containing the titles of the available
menus. Each menu title brings a specific menu.
The left column of the menu displays the menu items.
The top-right of the menu provides more detailed information when a
menu item is highlighted.
The bottom of the menu provides keyboard instructions for moving
around and making selections.
Using BIOS Setup
5-3
Moving Around and Making Selections
You must go through two or three levels to complete the setting for an
item. In most cases, there are three levels: menu title, pull-down menu,
and submenu.
Use the keyboard to move around and make selections. Keyboard
information can be found at the bottom of the screen. A brief description
of keyboard usage is listed next:
Key
5-4
Function
←,→
Selects a menu title.
↑,↓
Selects an item or option.
Enter
1) Brings up the sub-menu when available.
2) Opens or closes the option window when an item is selected.
Esc
1) Exits BIOS Setup Utility.
2) Closes the option window if one is open.
F9
Loads setup defaults.
F10
Saves and exit the BIOS Setup Utility.
Using BIOS Setup
Main Menu
The Main menu contains the system date and time settings as well as
shows the basic configuration of the system.
System Time sets the system time.
System Date sets the system date.
Using BIOS Setup
5-5
Advanced Menu
The Advanced menu contains various system settings.
Legacy USB Support allows you to enable support for Legacy USB
device in DOS mode.
Boot-time Diagnostic Screen allows you to display the diagnostic
screen during system boot.
5-6
Using BIOS Setup
Security Menu
The Security menu contains the security settings, which safeguard your
system against unauthorized use.
Supervisor/User Password Is shows whether you have set the
supervisor/user password or not for the system.
Set Supervisor/User Password sets the supervisor/user password.
When typing the password, first make sure that Num Lock is off, and then
type the password in the entry fields and press Enter. Confirm your
password by typing it again and pressing Enter. You can set the
supervisor/user password to be required for starting up the system and/or
entering SCU.
NOTE:
You can set the user password only when the supervisor password has been set.
If both the administrator and user passwords are set, you can enter any of them for
starting up the system and/or entering SCU. However, the user password only
allows you to view/change the settings of certain items.
Password on Boot allows you to enable or disable the entering of
password for booting up your system. Once the password is successfully
set and this item is enabled, it is required for booting up the system.
Using BIOS Setup
5-7
TPM Support allows you to enable or disable TPM support. TPM is a
component on your computer’s mainboard that is specifically designed to
enhance platform security above-and-beyond the capabilities of today’s
software by providing a protected space for key operations and other
security critical tasks. Using both hardware and software, TPM protects
encryption and signature keys at their most vulnerable stages – operations
when the keys are being used unencrypted in plain-text form. TPM is
specifically designed to shield unencrypted keys and platform
authentication information from software-based attacks.
NOTE: Make sure to install the TPM driver before you can use the TPM feature (see
chapter 6 for details).
Current TPM State shows the current TPM state.
Change TPM State allows you to select between No Change, Clear,
Deactivate & Disable, and Enable & Activate.
5-8
Using BIOS Setup
Boot Menu
The Boot menu sets the sequence of the devices to be searched for the
operating system.
The bootable devices will be automatically detected during POST and
shown here, allowing you to set the sequence that the BIOS use to look
for a boot device from which to load the operating system.
A brief description of keyboard usage is listed next:
Key
Function
↑,↓
Selects (highlight) a boot device.
+, –
Changes the boot sequence.
1 to 4
Loads the four default boot sequence.
Shift + 1
Enables or disables a device.
Moves the highlighted boot device from the “Boot priority order”
list to the “Excluded from boot order” list, and vice versa.
Using BIOS Setup
5-9
Exit Menu
The Exit menu displays ways of exiting BIOS Setup Utility. After
finishing with your settings, you must save and exit so that the changes
can take effect.
Exit Saving Changes saves the changes you have made and exits BIOS
Setup Utility.
Exit Discarding Changes exits BIOS Setup Utility without saving the
changes you have made.
Load Setup Defaults loads the factory default values for all the items.
Discard Changes restores the previous values for all the items.
Save Changes saves the changes you have made.
5-10
Using BIOS Setup
Chapter 6
CHAPTER
Installing Software Drivers
and Using the P1 Utility
To take full advantage of the unique features of your computer, some
operating systems require custom software, known as drivers, to be
installed.
If you purchased the computer with Windows pre-installed, your dealer
may have already installed the drivers. If not, you need to install the
drivers using the disc supplied with your computer.
Also, located on top of your keyboard is the P1 quick button. The quick
button utility allows you to re-define (customize) the P1 quick button
according to your needs.
This chapter describes how to install the drivers as well as use the P1
quick button utility.
Installing Software Drivers
6-1
How to Use the Driver Disc
NOTE:
The drivers may have been updated after this manual was published. For driver
upgrade, please contact your dealer.
This disc supports Windows Vista only.
The available items may differ according to your computer model.
Do not remove the driver disc when installing the driver.
An autorun program is provided on the driver disc to help you easily
install the drivers. As you insert the disc, the autorun program
automatically starts. If you need to start the program manually, run the
Setup.exe program from the Wsetup directory of the disc.
The main screen appears as shown next:
6-2
Installing Software Drivers
Click NEXT located on the right lower part of main screen to view the next
screen as shown next.
Click BACK to return to the main screen.
Installing Software Drivers
6-3
Installing Drivers
To install the intended driver, click on the particular item and installation
will start. The drivers are described next:
Name
Description
Chipset
Ensures the full function of the following drivers. Install this
driver before installing the other device drivers.
VGA
Installs the video driver that allows you to select
high-resolution displays with richer colors.
Audio
Installs the audio driver that allows you to take full advantage
of the audio subsystem.
Card Reader
Installs the driver that allows the Card Reader to access
MultiMediaCard (MMC), Secure Digital (SD), Memory Stick
(MS) or Memory Stick PRO (MS PRO) card for removable
storage media.
LAN
Installs the LAN driver that allows you to use the network
function of the computer.
System Utility Installs the system utility driver that allows you to use the hot
keys with OSD (on-screen display) on the computer.
Touchpad
Installs the touchpad driver that allows you to take full
advantage of the touchpad features.
Bluetooth
(option)
Installs the Bluetooth driver and application program that
allows you to use the Bluetooth feature.
WLAN
(option)
Installs the WLAN driver and application program that allows
you to use the computer’s internal mini PCI-E WLAN card’s
network function.
NOTE: The Windows Plug-and-Play capability may automatically
detect the new device (mini PCI-E WLAN card) and display the wizard
requesting for drivers. Click Cancel to bypass the wizard screen(s).
Installs the driver that allows you to use the fingerprint module
security verification system.
Installs the TPM driver, a hardware-based security feature that
allows you to create and manage computer-generated digital
certificates.
Fingerprint
TPM
6-4
Installing Software Drivers
Name
Description
Turbo
Memory
(option)
Installs the Turbo Memory driver that allows you to use the
computer’s internal mini PCI-E Robson ES2 card for boosting
system performance.
NOTE: This icon would not appear if the mini PCI-E Robson ES2 card
is not installed.
CCD (option)
Installs the web camera driver that allows you to use the
computer’s built-in camera function.
3G (option)
Installs the 3G driver that allows you to use the computer’s 3G
features.
Acrobat
Installs the Adobe Acrobat Reader program if you do not have
it on your computer. You need Adobe Acrobat Reader to open
the manual file supplied on this driver disc.
User’s Manual Allows you to view the User’s Manual.
Exit
Allows you to exit driver installation
(located on the right upper portion).
Installing Software Drivers
6-5
P1 Quick Button Utility
NOTE: Make sure to install the Quick Key driver to take advantage of the P1 quick
launch key utility.
The quick launch key utility allows you to define the “P1” quick launch
key.
icon and select the item Quick
To start the utility, right-click the
Button Definition. The following window appears as shown next.
Box
Open
6-6
Installing Software Drivers
Defining the buttons:
The box in the window represents the user-definable button.
To assign a program to a button, click the “Open” icon beside the box to
pop up the Open dialog box as shown next and select the desired program.
Then, click Open to complete the process.
The appropriate icon will then appear in the box. To launch the program,
press the P1 quick launch key, or, if the Quick Button Definition window is
open, click the box containing the icon.
Installing Software Drivers
6-7
Chapter 7
CHAPTER
Caring for the Computer
Taking good care of your computer will ensure a trouble-free operation
and reduce the risk of damage to your computer.
This chapter gives you guidelines covering these areas of maintenance:
How to protect the computer
What to note when using and storing the computer
How to clean the computer
What to note when using the battery pack
What to note when traveling with the computer
Caring for the Computer
7-1
Protecting the Computer
To safeguard the integrity of your computer data as well as the computer
itself, you can protect the computer in several ways as described in this
section.
Using the Windows Security Center
Windows Security Center protects your computer against intrusion.
7-2
Caring for the Computer
Windows Security Center alerts you to take action on the following
security essentials:
Windows Firewall
Windows Update
Malware Protection (anti-virus, anti-spyware)
Others (Internet security, user account control)
For detailed information on Windows Security Center, see Windows’
Help.
Using the Cable Lock
You can use a Kensington-type cable lock to protect your computer
against theft. The cable lock is available in most computer stores.
To use the lock, loop the lock cable around a stationary object such as a
table. Insert the lock to the Kensington lock hole and turn the key to
secure the lock. Store the key in a safe place.
Caring for the Computer
7-3
Taking Care of the Computer
Location Guidelines
Use the computer where the temperature is between 10 °C (50 °F) and
35 °C (95 °F).
Avoid placing the computer in a location subject to high humidity,
extreme temperatures, mechanical vibration, direct sunlight, or heavy
dust.
Do not cover or block any ventilation openings on the computer. For
example, do not place the computer on a bed, sofa, rug, or other
similar surface. Otherwise, overheating may occur that results in
damage to the computer.
Keep the computer at least 13 cm (5 inches) away from electrical
appliances that can generate a strong magnetic field such as a TV,
refrigerator, motor, or a large audio speaker.
Do not move the computer abruptly from a cold to a warm place. A
temperature difference of more than 10 °C (18 °F) will cause
condensation inside the unit, which may damage the storage media.
Do not place the computer on an unsteady surface.
General Guidelines
Wear protective gloves to prevent injury to your fingers when using
the computer in higher than normal temperature.
Do not place heavy objects on top of the computer when it is closed as
this may damage the display.
The screen surface is easily scratched. Do not use paper towels to
clean the display. Avoid touching it with your fingers, pen, or pencil.
To maximize the life of the backlight in the display, allow the
backlight to automatically turn off as a result of power management.
7-4
Caring for the Computer
Avoid using a screen saver or other software that prevents the power
management from working.
Cleaning Guidelines
Never clean the computer with its power on.
Use a soft cloth moistened with water or a non-alkaline detergent to
wipe the exterior of the computer.
Gently wipe the display with a soft, lint-free cloth. Do not use alcohol
or detergent on the display.
Dust or grease on the touchpad can affect its sensitivity. Clean the pad
by using adhesive tape to remove the dust and grease on its surface.
Battery Pack Guidelines
Recharge the battery pack when it is nearly discharged. When
recharging, make sure that the battery pack is fully charged. Doing so
may avoid harm to the battery pack.
Operate the computer with the battery pack installed even when using
external power. This ensures that the battery is fully charged.
If you will not be using the computer for a long period of time (more
than two weeks), remove the battery pack from the computer.
If you remove the battery pack, make sure that the battery terminals
do not contact any conductors such as metal objects or water.
Otherwise, the battery may become unusable as a result of a short
circuit.
If you need to store the battery pack, store it in a cool, dry place.
Never allow the temperature to exceed 60 °C (140 °F).
Do not leave the battery pack in storage for more than 6 months
without recharging it.
Caring for the Computer
7-5
When Traveling
Before traveling with your computer, make a backup of your hard
disk data into flash disks or other storage devices. As an added
precaution, bring along an extra copy of your important data.
Make sure that the battery pack is fully charged.
Make sure that the computer is turned off and the top cover is
securely closed.
Do not leave objects in between the keyboard and closed display.
Disconnect the AC adapter from the computer and take it with you.
Use the AC adapter as the power source and as a battery-charger.
Hand-carry the computer. Do not check it in as luggage.
If you need to leave the computer in the car, put it in the trunk of the
car to avoid exposing the computer to excessive heat.
When going through airport security, it is recommended that you
send the computer and flash disks through the X-ray machine (the
device you set your bags on). Avoid the magnetic detector (the device
you walk through) or the magnetic wand (the handheld device used
by security personnel).
If you plan to travel abroad with your computer, consult your dealer
for the appropriate AC power cord for use in your country of
destination.
7-6
Caring for the Computer
Chapter 8
CHAPTER
Troubleshooting
Computer problems can be caused by hardware, software, or both. When
you encounter any problem, it might be a typical problem that can easily
be solved.
This chapter tells you what actions to take when solving common
computer problems. It is divided into three sections:
Preliminary checklist
Solving common problems
Resetting the computer
Troubleshooting
8-1
Preliminary Checklist
Here are helpful hints to follow before you take further actions when you
encounter any problem:
Try to isolate which part of the computer is causing the problem.
Make sure that you turn on all peripheral devices before turning on
the computer.
If an external device has a problem, make sure that the cable
connections are correct and secure.
Make sure that the configuration information is properly set in the
BIOS Setup program.
Make sure that all the device drivers are correctly installed.
Make notes of your observations. Are there any messages on the
screen? Do any indicators light? Do you hear any beeps? Detailed
descriptions are useful to the service personnel when you need to
consult one for assistance.
If any problem persists after you follow the instructions in this chapter,
contact an authorized dealer for help.
8-2
Troubleshooting
Solving Common Problems
For easy reference, the problems are divided into these categories.
Problem Type
Go to
Battery Problems
P. 8-4
Bluetooth Wireless Problems
P. 8-4
DVD Drive Problems
P. 8-4
Display Problems
P. 8-5
ExpressCard Problems
P. 8-6
Hardware Device Problems
P. 8-6
Hard Disk Drive Problems
P. 8-7
Keyboard, Mouse, and Touchpad Problems
P. 8-8
LAN Problems
P. 8-8
WLAN Problems
P. 8-9
Power Management Problems
P. 8-10
Software Problems
P. 8-11
Sound Problems
P. 8-11
Startup Problems
P. 8-12
Other Problems
P. 8-13
Troubleshooting
8-3
Battery Problems
The battery does not charge (Battery Charge indicator does not light
amber).
Make sure that the AC adapter is properly connected.
Make sure that the battery is not too hot or cold. Allow time for the
battery pack to return to room temperature.
Make sure that the battery pack is installed correctly.
Make sure that the battery terminals are clean.
The operating time of a fully charged battery becomes shorter.
If you often partially recharge and discharge, the battery might not be
charged to its full potential. Initialize the battery to solve the problem.
(See “Initializing the Battery Pack” in Chapter 3 for instructions.)
The battery operating time indicated by the battery meter does not
match the actual operating time.
The actual operating time can be different from the estimated time,
depending on how you are using the computer. If the actual operating
time is much less than the estimated time, initialize the battery. (See
“Initializing the Battery Pack” in Chapter 3 for instructions.)
Bluetooth Wireless Problems
I cannot connect to another Bluetooth-enabled device.
Make sure that the Bluetooth card is correctly installed.
Make sure that the Bluetooth driver is correctly installed.
Make sure that both devices have activated Bluetooth.
Make sure that the distance between the two devices are not over
10 meters or that there are no walls or other obstructions between the
devices.
Make sure that the other device is not in “Hidden” mode.
8-4
Troubleshooting
Make sure that both devices are compatible.
DVD Drive Problems
The DVD drive cannot read a disc.
Make sure that the disc is correctly seated in the tray, with the label
facing up.
Make sure that the disc is not dirty. Clean the disc with a disc
cleaning kit, available in most computer stores.
Make sure that the DVD drive driver is installed correctly.
Make sure that the computer supports the disc or the files contained.
You cannot eject a disc.
The disc is not properly seated in the drive. Manually release the disc
following the method described next:
1. Insert a small rod, such as a straightened paperclip, into the
drive’s manual eject hole and push firmly to release the tray.
2. Pull the tray out until fully extended, and then remove the disc.
Display Problems
Nothing appears on the screen.
Make sure that the VGA driver is installed properly.
During operation, the screen may automatically turn off as a result of
power management. Press any key to see if the screen comes back.
Troubleshooting
8-5
The brightness level might be too low. Increase brightness by
pressing the Fn+F7 hot key.
The display output might be set to an external device. To switch the
display back to the LCD, press the Fn+F5 hot key or change the
display through the Display Settings Properties of Windows.
The characters on the screen are dim.
Adjust the brightness and/or contrast.
Bad dots appear on the display at all times.
A small number of missing, discolored, or bright dots on the screen
are an intrinsic characteristic of TFT LCD technology. It is not
regarded as a LCD defect.
The external monitor displays nothing.
Make sure that the monitor is turned on.
Make sure that the monitor’s signal cable is properly connected.
Switch the display to the monitor by pressing the Fn+F5 hot key or
change the display through the Display Settings Properties of
Windows.
Simultaneous display/multi-display does not work.
Make sure that you turn on the external monitor before turning on the
computer.
Press the Fn+F5 hot key to toggle through the display options or
through the Display Settings Properties of Windows.
ExpressCard Problems
The ExpressCard does not work.
Make sure that the ExpressCard is correctly seated.
If the card requires an IRQ (Interrupt ReQuest), make sure that there
is one available.
8-6
Troubleshooting
The ExpressCard stops communicating properly.
The application may have been reset when the computer is turned off
or in Sleep mode. Exit and restart the application.
Hardware Device Problems
The computer does not recognize a newly installed device.
The device may not be correctly configured in the BIOS Setup
program. Run the BIOS Setup program to identify the new type.
Make sure if any device driver needs to be installed. (Refer to the
documentation that came with the device.)
Make sure if the device needs any jumper or switch settings. (Refer to
the documentation that came with the device.)
Check the cables or power cords for correct connections.
For an external device that has its own power switch, make sure that
the power is turned on.
Hard Disk Drive Problems
The hard disk drive error message appears on the screen.
The hard disk drive has defects. Ask your dealer for help.
The hard disk drive operations seem slow.
The data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
The hard disk drive in-use indicator glows without blinking.
The data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
Troubleshooting
8-7
Keyboard, Mouse, and Touchpad Problems
The keyboard does not respond.
Try connecting an external keyboard. If it works, contact an
authorized dealer, as the internal keyboard cable might be loose.
The numeric keypad is disabled.
Make sure that the Num Lock is switched on. (Check if the Num Lock
Indicator glows or not.)
The external keyboard does not work.
Make sure that the keyboard cable is properly connected.
The USB mouse does not work.
Make sure that the mouse cable is properly connected.
The touchpad does not work, or the pointer is difficult to control
with the touchpad.
Make sure that the touchpad driver is correctly installed.
Make sure that the touchpad is clean.
LAN Problems
I cannot access the network.
Make sure that the LAN driver is correctly installed.
Make sure that the LAN cable is properly connected to the RJ-45
connector and the network hub.
Make sure that the network configuration is appropriate.
Make sure that the user name or password is correct.
8-8
Troubleshooting
WLAN Problems
I cannot use the WLAN feature.
Make sure that the mini PCI-E WLAN card is correctly installed.
Make sure that the necessary driver(s) is correctly installed.
Make sure that the WLAN feature is turned on.
Transmission quality is poor.
Your computer may be in an out-of-range situation. Move your
computer closer to the Access Point or another WLAN device it is
associated with.
Check if there is high interference around the environment and solve
the problem as described next.
Radio interference exists.
Move your computer away from the device causing the radio
interference such as microwave oven and large metal objects.
Plug your computer into an outlet on a different branch circuit from
that used by the affecting device.
Consult your dealer or an experienced radio technician for help.
I cannot connect to another WLAN device.
Make sure that the WLAN feature is turned on.
Make sure that the SSID setting is the same for every WLAN device
in the network.
Your computer is not recognizing changes. Restart the computer.
Make sure that the IP address or subnet mask setting is correct.
I cannot communicate with the computer in the network when
Infrastructure mode is configured.
Make sure that the Access Point your computer is associated with is
powered on and all the LEDs are working properly.
Troubleshooting
8-9
If the operating radio channel is in poor quality, change the Access
Point and all the wireless station(s) within the BSSID to another radio
channel.
Your computer may be in an out-of-range situation. Move your
computer closer to the Access Point it is associated with.
Make sure that your computer is configured with the same security
option (encryption) to the Access Point.
Use the Web Manager/Telnet of the Access Point to check whether it
is connected to the network.
Reconfigure and reset the Access Point.
I cannot access the network.
Make sure that the necessary driver(s) is correctly installed.
Make sure that the network configuration is appropriate.
Make sure that the user name or password is correct.
You have moved out of range of the network.
Turn off power management.
Power Management Problems
The computer does not enter Sleep or Hibernation mode
automatically.
If you have a connection to another computer, the computer does not
enter Sleep or Hibernation mode if the connection is actively in use.
Make sure that the Sleep or Hibernation time-out is enabled.
The computer does not enter Sleep or Hibernation mode
immediately.
If the computer is performing an operation, it normally waits for the
operation to finish.
8-10
Troubleshooting
The computer does not resume from Sleep or Hibernation mode.
The computer automatically enters Sleep or Hibernation mode when
the battery pack is empty. Do any one of the following:
− Connect the AC adapter to the computer.
− Replace the empty battery pack with a fully charged one.
The computer does not enter Hibernation mode with the Fn+F12 hot
keys.
Make sure that the Hibernation function is specified for the sleep
button.
You might be using an ExpressCard that prevents the computer from
entering Hibernation mode. To enter the mode, stop the
communication program and then remove the card or stop the card.
Software Problems
An application program does not work correctly.
Make sure that the software is correctly installed.
If an error message appears on the screen, consult the software
program’s documentation for further information.
If you are sure the operation has stop, reset the computer. (See
“Resetting the Computer” later in this chapter.)
Sound Problems
No sound is produced.
Make sure that the volume control is not set too low.
Make sure that the audio driver is correctly installed.
Make sure that the computer is not in Sleep mode.
If using an external speaker, make sure that the speaker is properly
connected.
Troubleshooting
8-11
Distorted sound is produced.
Make sure that the volume control is not set too high or too low. In
most cases, a high setting can cause the audio electronics to distort the
sound.
The sound system does not record.
Adjust the playback or recording sound levels.
The external microphone or audio device does not work.
Make sure that the microphone is connected to the proper connector
on the computer.
Make sure that your computer is equipped with the driver needed.
Click the speaker symbol on the taskbar and check the Windows
volume control.
Check the volume control of your computer.
Startup Problems
When you turn on the computer, it does not respond.
If you are using an external AC power, make sure that the AC adapter
is correctly and securely connected. If so, make sure that the electrical
outlet works properly.
If you are using the battery power, make sure that the battery is not
discharged.
When you turn on the computer, it stops after POST.
Restart your computer.
The message “Operating system not found” appears on the
screen after you turn on the computer.
If this message appears when you are booting from the hard disk,
insert a bootable disc in the DVD drive and check the condition of the
hard disk.
8-12
Troubleshooting
The message “Invalid system disk” or “Disk error” appears
on the screen after you turn on the computer.
If you are deliberately trying to boot from a disc, replace the disc with
a bootable one and press any key to continue booting.
If this message appears when you are booting from the hard disk,
insert a bootable disc in the DVD drive and check the condition of the
hard disk.
Other Problems
The date/time is incorrect.
Correct the date and time via the operating system or BIOS Setup
program.
After you have performed everything as described above and still
have the incorrect date and time every time you turn on the computer,
the RTC (Real-Time Clock) battery is at the end of its life. Call an
authorized dealer to replace the RTC battery.
Troubleshooting
8-13
Resetting the Computer
You may have to reset (reboot) your computer on some occasions when
an error occurs and the program you are using hangs up.
If the computer operation seems to hang up, first wait. It is possible that
the computer is processing data. Periodically check the hard disk drive
in-use indicator, if it flashes irregularly, the program may be accessing
data and preventing you from using the keyboard. If you are sure the
operation has stopped and you cannot use the “restart” function of the
operating system, reset the computer.
Reset the computer by any one of these methods:
Press Ctrl+Alt+Del.
If the above action does not work, turn off the computer. Wait for at
least five seconds and turn it on again.
CAUTION: Resetting will cause any unsaved data to be lost.
8-14
Troubleshooting
Appendix A
APPENDIX
Specifications
NOTE: Specifications are subject to change without any prior notice.
Parts
Durability
100 c.c. water on system cover
Drop
45 cm height (operating and non-operating)
Stress
120 kg on surface, 15 kg / 13 points on LCD housing
NorthBridge
Intel® Mobile Penryn (ultra-low voltage) Montevina (small form
factor) processor, 800 MHz FSB (Front Side Bus), Thermal
specifications 10 W (maximum)
Intel® GS45
CPU
Chipset
SouthBridge
ROM BIOS
RAM
System
Display
Panel
Audio
Specifications
Spill-resistant
Intel® ICH9-E (small form factor)
2 MB EEPROM, Fingerprint and TPM security
Up to 3 GB, 200-pin, DDRII 800 MHz SO-DIMM, 1.25-inch height
13.3-inch TFT, resolution up to 1280×800 WXGA
Video controller
UMA
Video ports
Subsystem
VGA port
Azalia interface, 2.1-channel analog output
Ports
Three audio ports for Line-out / Mic-in / S/PDIF
Speakers
2 × 1.5 Watt stereo
Microphone
× 2 Mic array
Keyboard
Quick keys
Pointing device
Storage
Hard disk drive
device
Optical drive
Card slots
Specifications
Standard keys, numeric keypad, 12 function keys, a special Fn
(Function) key and Windows keys
ECO (power saving), Microsoft® Internet Explorer®, and
P1 (Program 1 – user customized) quick launch key
Glide touchpad without scroll bar and 2 buttons
SATA interface, 4200/5400 rpm support, 9.5 mm height,
2.5-inch diameter
DVD Super Multi, 9.5 mm height
ExpressCard/34, Card Reader (SD / MS / MS Pro / MMC)
A-1
Parts
Specifications
I/O ports
LAN
Wireless LAN
Three USB ports (USB 2.0 support), RJ-45 port, port replicator
10/100/1000 based-T
One mini PCI-E slot for wireless LAN card, compliant with
IEEE 802.11a/b/g/n
Bluetooth
3G
Camera
Security
Specification 2.1 module
Sierra 8790 module, HSUPA
Webcam 1.3 M with Mic array
Fingerprint sensor slide-type, TPM 1.2, Kensington lock
Power
AC adapter
Battery
Dimension (W×D×H)
Weight
Environment
Temperature
Humidity
Regulation
EMC
Safety
Universal AC adapter 65 Watt; input: 100∼240 Volt, output: 19 Volt
3-cell Li-ion battery 2600 mAh / 14.8 V
6-cell Li-ion battery 5200 mAh / 11.1 V
321×228×20~29 mm (12.6×9×0.8~1.14 inch)
1.7 kg (3.75 lb)
Operating: 0 °C (32 °F) to 35 °C (95 °F)
Storage: –20 °C (–4 °F) to 60 °C (140 °F)
Operating: 10 % to 90 % non-condensing
Storage: 5 % to 95 % non-condensing
CE
Energy Star
CB
Energy Star 4.0
Green Product Coverage
RoHS-compliant
A-2
Specifications
Appendix B
APPENDIX
Regulatory Information
This appendix provides regulatory statements and safety notices on your
computer.
NOTE: Marking labels located on the exterior of your computer indicate the regulations
that your model complies with. Please check the marking labels and refer to the
corresponding statements in this appendix. Some notices apply to specific models only.
Regulatory Information
B-1
On the Use of the System
Class B Regulations
USA
Federal Communications Commission Radio Frequency
Interference Statement
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Please note:
The use of a non-shielded interface cable with this equipment is
prohibited.
B-2
Regulatory Information
Canada
Canadian Department of Communications
Radio Interference Regulations Class B Compliance Notice
This Class B digital apparatus meets all requirements of the Canada
Interference-Causing equipment regulations.
Cet appareil numérique de Classe B respecte toutes les exigences du
Règlement Canadien sur le matériel brouileur.
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.
Safety Notices
About the Battery
Caution Texts Concerning Lithium Batteries
DANISH
ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må
kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til
leverandøren.
NORWEGIAN
ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype
eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i
henhold til fabrikantens instruksjoner.
SWEDISH
VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt
fabrikantens instruktion.
FINNISH
VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
Regulatory Information
B-3
ENGLISH
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the equipment manufacturer. Discard used
batteries according to manufacturer's instructions.
DEUTSCH
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur
durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
FRENCH
ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d’un type équivalent
recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
Attention (for USA Users)
The product that you have purchased contains a rechargeable battery. The
battery is recyclable. At the end of its useful life, under various state and
local laws, it may be illegal to dispose of this battery into the municipal
waste stream. Check with your local solid waste officials for details in
your area for recycling options or proper disposal.
About the AC Adapter
Use only the AC adapter supplied with your computer. Use of another
type of AC adapter will result in malfunction and/or danger.
Do not use the adapter in a high moisture environment. Never touch
the adapter when your hands or feet are wet.
Allow adequate ventilation around the adapter when using it to
operate the device or charge the battery. Do not cover the AC adapter
with paper or other objects that will reduce cooling. Do not use the
AC adapter while it is inside a carrying case.
Connect the adapter to a proper power source. The voltage
requirements are found on the product case and/or packaging.
Do not use the adapter if the cord becomes damaged.
Do not attempt to service the unit. There are no serviceable parts
inside. Replace the unit if it is damaged or exposed to excess
moisture.
B-4
Regulatory Information
On the Use of the RF Device
NOTE: The information in this section applies to models with the wireless LAN module.
USA and Canada Safety Requirements and Notices
IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Radio Frequency Interference Requirements and SAR
The FCC with its action in ET Docket 93-62 has adopted a safety standard
for human exposure to Radio Frequency (RF) electromagnetic energy
emitted by FCC certified equipment. The wireless LAN module meets the
Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE
C95.1, 1992. Proper operation of this radio according to the instructions
found in this manual will result in exposure substantially below the
FCC’s recommended limits. The following safety precautions should be
observed:
Do not touch or move antenna while the unit is transmitting or
receiving.
Do not hold any component containing the radio such that the
antenna is very close or touching any exposed parts of the body,
especially the face or eyes, while transmitting.
Do not operate the radio or attempt to transmit data unless the antenna
is connected; if not, the radio may be damaged.
Use in specific environments:
The use of wireless devices in hazardous locations is limited by the
constraints posed by the safety directors of such environments.
The use of wireless devices on airplanes is governed by the Federal
Aviation Administration (FAA).
Regulatory Information
B-5
The use of wireless devices in hospitals is restricted to the limits set
forth by each hospital.
Antenna use:
In order to comply with FCC RF exposure limits, low gain integrated
antennas should be located at a minimum distance of 20 cm
(8 inches) or more from the body of all persons.
High-gain, wall-mount, or mast-mount antennas are designed to be
professionally installed and should be located at a minimum distance
of 30 cm (12 inches) or more from the body of all persons. Please
contact your professional installer, VAR, or antenna manufacturer for
proper installation requirements.
Explosive Device Proximity Warning
WARNING: Do not operate a portable transmitter (such as a wireless
network device) near unshielded blasting caps or in an explosive
environment unless the device has been modified to be qualified for such
use.
Antenna Warning
WARNING: To comply with the FCC and ANSI C95.1 RF exposure limits,
it is recommended that the antenna for this device be installed so as to
provide a separation distance of at least 20 cm (8 inches) from all persons
and that the antenna must not be co-located or operating in conjunction
with any other antenna or radio transmitter. It is recommended that the
user limit exposure time if the antenna is positioned closer than 20 cm
(8 inches).
Use on Aircraft Caution
CAUTION: Regulations of the FCC and FAA prohibit airborne operation
of radio-frequency wireless devices because their signals could interfere
with critical aircraft instruments.
B-6
Regulatory Information
EMC Requirements
This device uses, generates and radiates radio frequency energy. The
radio frequency energy produced by this device is well below the
maximum exposure allowed by the Federal Communications
Commission (FCC).
This device complies with the limits for a Class B digital device pursuant
to Part 15 subpart C of the FCC Rules and Regulations. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
The FCC limits are designed to provide reasonable protection against
harmful interference when the equipment is installed and used in
accordance with the instruction manual and operated in a commercial
environment. However, there is no guarantee that interference will not
occur in a particular commercial installation, or if operated in a residential
area.
If harmful interference with radio or television reception occurs when the
device is turned on, the user must correct the situation at the user’s own
expense. The user is encouraged to try one or more of the following
corrective measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: The Part 15 radio device operates on a non-interference basis
with other devices operating at this frequency. Any changes or
modification to said product not expressly approved by the manufacturer
could void the user’s authority to operate this device.
Regulatory Information
B-7
Canada Radio Frequency Interference Requirements
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and away from windows to provide
maximum shielding. Equipment (or its transmit antenna) that is installed
outdoors is subject to licensing.
Pour empêcher que cet appareil cause du brouillage au service faisant
l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé
loin des fenêtres afin de fournir un écran de blindage maximal. Si le
matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire
l'objet d'une licence.
European Union CE Marking and Compliance Notices
Statements of Compliance
English
This product follows the provisions of the European Directive
1999/5/EC.
Danish
Dette produkt er i overensstemmelse med det europæiske direktiv
1999/5/EC.
Dutch
Dit product is in navolging van de bepalingen van Europees Directief
1999/5/EC.
Finnish
Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä.
French
Ce produit est conforme aux exigences de la Directive Européenne
1999/5/EC.
German
Dieses Produkt entspricht den Bestimmungen der Europäischen
Richtlinie 1999/5/EC.
B-8
Regulatory Information
Greek
To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας
1999/5/EC.
Icelandic
Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
1999/5/EC.
Italian
Questo prodotto è conforme alla Direttiva Europea 1999/5/EC.
Norwegian
Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
1999/5/EC.
Portuguese
Este produto cumpre com as normas da Diretiva Européia 1999/5/EC.
Spanish
Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
Swedish
Denna produkt har tillverkats i enlighet med EG-direktiv 1999/5/EC.
Local Restrictions of 802.11a/b/g/n Radio Usage
802.11a wireless LAN devices: For operation within 5.15 ~ 5.25 GHz
frequency range, it is restricted to indoor usage environments, and the
antenna of this device must be integral.
CAUTION: Due to the fact that the frequencies used by 802.11a/b/g/n
wireless LAN devices may not yet be harmonized in all countries,
802.11a/b/g/n products are designed for use only in specific countries or
regions, and is not allowed to be operated in countries or regions other
than those of designated use. As a user of these products, you are
responsible for ensuring that the products are used only in the countries or
regions for which they were intended and for verifying that they are
configured with the correct selection of frequency and channel for the
country or region of use. Any deviation from permissible settings and
restrictions in the country or region of use could be an infringement of
local law and may be punished as such.
Regulatory Information
B-9
The European variant is intended for use throughout the European
Economic Area. However, authorization for use is further restricted in
particular countries or regions within countries, as follows:
General
European standards dictate maximum radiated transmit power of
100 mW Effective Isotropic Radiated Power (EIRP) and the frequency
range 2400 – 2483.5 MHz.
Belgium and the Netherlands
In Belgium and the Netherlands, the product may not be used outdoors.
See the instructions next under the heading “Turning Off the Wireless
LAN Radio.”
France
Departments in Which the Wireless LAN Module Can Be Used
(Indoors Only)
The wireless LAN module can currently be used indoors only in the
following 38 departments of mainland France. Please turn off your
wireless LAN radio when operating the device in areas/places other than
the 38 departments listed:
B-10
01
Ain Orientales
36
Indre
66
Pyrénées
02
Aisne
37
Indre et Loire
67
Bas Rhin
03
Allier
41
Loir et Cher
68
Haut Rhin
05
Hautes Alpes
42
Loire
70
Haute Saône
08
Ardennes
45
Loiret
71
Saône et Loire
09
Ariège
50
Manche
75
Paris
11
Aude
55
Meuse
82
Tarn et Garonne
12
Aveyron
58
Nièvre
84
Vaucluse
16
Charente
59
Nord
88
Vosges
24
Dordogne
60
Oise
89
Yonne
25
Doubs
61
Orne
90
Territoire de Belfort
26
Drôme
63
Puy du Dôme
94
Val de Marne
32
Gers
64
Pyrénées Atlantique
Regulatory Information
Departments in Which the Wireless LAN Module’s Maximum EIRP
Not Shown in the Previous Table
Frequency Ranges (MHz)
Indoors
Outdoors
2400 – 2446.5
10 mW
Not permitted
2446.5 – 2483.5
100 mW
100 mW on private property with
Ministry of Defense approval
Turning Off the Wireless LAN Radio
NOTE: Turning the wireless LAN radio off is not the same as disabling the
wireless LAN card. It is not necessary to disable the card to meet the
regulatory requirements.
While operating the computer in those French departments that do not
allow use of the wireless LAN equipment, the user of the equipment must
turn off the wireless LAN radio in order to comply with local regulations
(see Chapter 2 for more information).
Regulatory Information
B-11
Index
—A—
AC adapter, 3-2
Connecting, 1-2
Specifications, A-2
AC power
Connecting, 1-2
ACPI, 3-12
Adobe Acrobat Reader, 6-5
Alt key, 2-5
Antenna warning, B-7
Audio connector, 2-21
Audio driver, 6-4
Audio output connector, 1-10, 2-22
Audio subsystem
Connecting external audio device, 2-22
Driver installation, 6-4
Feature, 2-21
Specifications, A-1
Troubleshooting, 8-12
—B—
Battery charge
Indicator, 1-14, 3-3
Battery low, 3-11
Battery pack, 1-11
Battery low, 3-11
Charging, 3-3
Checking battery level, 3-5
Initializing, 3-4
Replacing, 3-6
Index
Safety notices, B-3
Secondary, 1-6, 3-8
Specifications, A-2
Taking care, 3-3, 7-6
Troubleshooting, 8-4
BIOS Setup, 5-1
Advanced menu, 5-6
Boot menu, 5-8
Exit menu, 5-9
Exiting, 5-9
Legacy USB, 5-6
Main menu, 5-5
Security menu, 5-7
Starting, 5-2
Bluetooth feature
Connecting to Bluetooth device, 2-37
Driver installation, 6-4
Indicator, 1-14
Turning off, 2-36
Turning on, 2-36
Using, 2-36
Boot sequence, 5-8
Booting, 2-2
Brightness
Hot keys, 2-8
—C—
Canada
Class B compliance notice, B-3
RF interference requirements, B-9
Caps Lock
Indicator, 1-13
I-1
Card Reader, 4-11, See Storage card
Driver installation, 6-4
Indicator, 1-14
Inserting a card, 4-12
Removing a card, 4-12
CD. See DVD drive
Charging, 3-3
Chipset driver, 6-4
Class 1 laser product, 2-16
Cleaning the computer, 7-6
Click, 2-11
Connecting external device
Monitor, 4-2
USB device, 4-4
Connector
Audio output, 1-10, 2-22
Microphone, 1-10, 2-22
RJ-45, 1-7
VGA, 1-8
Copyright protection
Macrovision Corp., 2-17
Cover
Opening, 1-4
CPU, A-1
Ctrl key, 2-5
Cursor, 2-6
Cursor-control key, 2-6
—D—
Date
BIOS Setup, 5-5
Troubleshooting, 8-14
DC, 3-2
Dimension of the computer, A-2
Display
Troubleshooting, 8-5
Display mode, 2-19
Display output
Hot keys, 2-8
Double-click, 2-11
Drag and drop, 2-11
Drive C, 2-13
Drive E, 4-12
Driver installation, 6-1
Driver OS support, 6-2
I-2
DVD drive, 1-6, 2-16
Inserting a disc, 2-17
Troubleshooting, 8-4
DVD Dual drive. See DVD drive
—E—
EEPROM, A-1
EMC requirements, B-8
Environmental specifications, A-2
Esc key, 2-5
EU
CE marking and compliance notices,
B-9
Euro symbol, 2-9
External monitor
Connecting, 4-2
—F—
FCC
Class B regulations, B-2
FDA regulations, 2-16
Fingerprint
Enrolling, 2-42
Fingerprint module
Driver installation, 6-5
Fingerprint sensor, 1-13
Using, 2-40
Fingerprint software
Change setting, 2-44
Fn key, 2-7
Function key, 2-7
—G—
Gas gauge
Battery pack, 3-6
Secondary battery pack, 3-10
Index
—H—
Hard disk drive
Indicator, 1-13
Secondary, 1-6, 2-13
Troubleshooting, 8-7
Hibernation, 2-3, 3-12, 3-13
Troubleshooting, 8-11
Hot keys, 2-7
Display output, 2-8
LCD, 2-8
LCD brightness, 2-8
Mute, 2-8
Power saving, 2-8
Touchpad, 2-8
Volume, 2-8
WLAN radio, 2-8
Humidity, A-2
—I—
Indicator
Battery charge, 1-14, 3-3
Bluetooth feature, 1-14
Caps Lock, 1-13
Card Reader, 1-14
Hard disk drive, 1-13
Num Lock, 1-13
Optical drive, 1-13
Power, 1-14
WLAN, 1-13
—K—
Kensington lock, 1-9, 7-4
Keyboard, 1-13
Troubleshooting, 8-7
Using, 2-5
—L—
LAN, 2-31
Connector, 1-7
Index
Driver installation, 6-4
Troubleshooting, 8-8
LCD, 1-12, 2-19
Switching on and off with hot keys, 2-8
Location of the computer, 7-5
Low battery. See Battery low
—M—
Memory card. See Storage card
Memory Stick. See Storage card
Memory Stick PRO. See Storage card
Microphone, 1-10, 2-21
Microphone connector, 1-10, 2-22
Mouse
Troubleshooting, 8-7
MultiMediaCard. See Storage card
Mute
Hot keys, 2-8
—N—
Network. See LAN
Num Lock
Indicator, 1-13
Numeric key, 2-6
—O—
Operating system, 1-5, 2-2
Optical drive
Indicator, 1-13
OSD utility
Driver installation, 6-5
—P—
P1 utility
Defining the button, 6-7
Using, 6-6
Point, 2-11
POST, 1-5
I-3
Power
Indicator, 1-14
Power button, 1-13, 2-2
Power connector, 1-9
Power Management, 3-12
Troubleshooting, 8-11
Power-On Self Test. See POST
—Q—
Quick button
ECO, 1-12, 2-4
P1, 1-12, 2-4
Using, 2-4
—R—
RAM, A-1
Rebooting, 8-15
Record volume
Adjusting, 2-23
Resetting
Computer, 8-15
Restarting
Computer, 8-15
RF device
Safety Requirements and Notices, B-6
RF switch, 1-8
RJ-45, 1-7, 2-31
ROM BIOS, A-1
—S—
Saving power, 3-14
Screen. See LCD
Scroll, 2-12
Secure Digital. See Storage card
Security
Protecting the computer with lock, 7-4
Protecting the computer with password,
7-3
Shutting down, 2-2
Computer, 1-5
Simultaneous display, 2-19
I-4
Sleep button
Hot keys, 2-8
Sleep mode, 2-2, 3-12
Troubleshooting, 8-11
Software
Troubleshooting, 8-12
Software driver, 6-1
Speaker, 1-11, 2-21
Connecting external speakers, 2-22
Specifications, A-1
Startup
Computer, 2-2
Troubleshooting, 8-13
Storage card, 4-11
Inserting, 4-12
Removing, 4-12
Super Multi drive. See DVD drive
Swappable bay, 1-6
—T—
Temperature, A-2
TFT, 2-19
Time
BIOS Setup, 5-5
Troubleshooting, 8-14
Touchpad, 1-13, 2-10
Configuring, 2-12
Driver installation, 6-4
Hot keys, 2-8
Troubleshooting, 8-7
TPM
BIOS Setup, 5-7
Driver installation, 6-5
Traveling with the computer, 7-7
Troubleshooting, 8-1
Battery problem, 8-4
Bluetooth problem, 8-4
Display problem, 8-5
DVD drive problem, 8-4
Hard disk drive problem, 8-7
Hardware problem, 8-6
Keyboard problem, 8-7
LAN problem, 8-8
Mouse problem, 8-7
Other problem, 8-14
Index
Power Management problem, 8-11
Software problem, 8-12
Sound problem, 8-12
Startup problem, 8-13
Touchpad problem, 8-7
WLAN problem, 8-8
Turning off, 2-2
Computer, 1-5
Turning on
Computer, 1-4
Typewriter key, 2-5
—U—
Upgrading the computer, 4-13
USB device
Connecting, 4-4
USB port, 1-7, 1-8, 4-4
—V—
VGA connector, 1-8, 4-2
Video driver, 6-4
Video subsystem
Configuring, 2-19
Index
Driver installation, 6-4
Feature, 2-19
Video controller, A-1
Volume control
Hot keys, 2-8
—W—
Weight of the computer, A-2
Windows key, 2-9
Windows Security Center, 7-2
Wireless network
Connecting, 2-33
WLAN card, 1-11
WLAN feature
Driver installation, 6-4
Troubleshooting, 8-8
Turning off, 2-33
Turning on, 2-33
Using, 2-32
WLAN radio
Indicator, 1-13
France restrictions, B-11
Hot keys, 2-8
Local restrictions, B-10
I-5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
Page Count                      : 73
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:253c6d48-ca48-437d-be47-8c223645436a
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Create Date                     : 2008:09:26 10:03:08+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:09:26 10:07:13+08:00
Metadata Date                   : 2008:09:26 10:07:13+08:00
Document ID                     : uuid:1469ecbd-7edd-40d4-b5de-cd695053ebdb
Format                          : application/pdf
Creator                         : kety_h
Title                           : Microsoft Word - 9213 User's Manual.DOC
Author                          : kety_h

EXIF Metadata provided by EXIF.tools