Getac Technology 9213L Notebook with WLAN and Bluetooth User Manual 9213 User s Manual AW

Download:
Mirror Download [FCC.gov]
Document ID	1018825
Application ID	I0VpZ38xj1WIARZ0gXM0ww==
Document Description	Users Manual rv1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	255.36kB (3191995 bits)
Date Submitted	2008-10-21 00:00:00
Date Available	2008-10-23 00:00:00
Creation Date	2008-10-13 16:10:39
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2008-10-13 16:15:58
Document Title	Microsoft Word - 9213 User's Manual-AW.DOC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	kety_h

User’s Manual
(September 2008)
WARNING
Do not attempt to disassemble your notebook computer. Doing so may void
your warranty. There are no serviceable parts inside. Please refer all servicing
to a qualified personnel.
TRADEMARKS
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. All
brand and product names are trademarks or registered trademarks of their
respective companies.
NOTE
The information in this manual is subject to change without notice.
ENERGY STAR® is a government program that offers businesses and
consumers energy-efficient solutions, making it easy to save money while
protecting the environment for future generations.
Please reference ENERGY STAR® related information from
www.energystar.gov.
As an ENERGY STAR® Partner, MiTAC Technology Corporation has
determined that this product meets the ENERGY STAR® guidelines for
energy efficiency.
An ENERGY STAR® qualified computer uses 70 % less electricity than
computers without enabled power management features.
Earning the ENERGY STAR®
When every home office is powered by equipment that has earned the
ENERGY STAR®, the change will keep over 289 billion pounds of
greenhouse gases out of the air.
If left inactive, ENERGY STAR® qualified computers enter a
low-power mode and may use 15 watts or less. New chip
technologies make power management features more reliable,
dependable, and user-friendly than even just a few years ago.
Spending a large portion of time in low-power mode not only saves
energy, but helps equipment run cooler and last longer.
Businesses that use ENERGY STAR® enabled office equipment may
realize additional savings on air conditioning and maintenance.
Over its lifetime, ENERGY STAR® qualified equipment in a single
home office (e.g., computer, monitor, printer, and fax) can save
enough electricity to light an entire home for more than 4 years.
Power management (“sleep settings”) on computers and monitors can
result in much savings annually.
Remember, saving energy prevents pollution
Because most computer equipment is left on 24 hours a day, power
management features are important for saving energy and are an easy way
to reduce air pollution. By using less energy, these products help lower
consumers’ utility bills, and prevent greenhouse gas emissions.
Table of Contents
Table of Contents........................................................................i
Preface
Notational Conventions.......................................................vi
Getting Started ........................................................................1-1
Getting the Computer Running ............................................ 1-2
Unpacking ........................................................................ 1-2
Connecting to AC Power ................................................. 1-2
Opening the Cover ........................................................... 1-4
Turning On and Off the Computer................................... 1-4
Taking a Look at the Computer............................................ 1-6
Right-Side Components ................................................... 1-6
Left-Side Components ..................................................... 1-7
Front Components............................................................ 1-8
Bottom Components......................................................... 1-9
Top-open Components ................................................... 1-10
Where to Go from Here...................................................... 1-13
Operating Your Computer ......................................................2-1
Starting and Stopping the Computer .................................... 2-2
Starting the Computer ...................................................... 2-2
Stopping the Computer .................................................... 2-2
Using the Quick Buttons ...................................................... 2-4
Using the Keyboard.............................................................. 2-5
Typewriter Keys............................................................... 2-5
Cursor-Control Keys ........................................................ 2-6
Numeric Keypad .............................................................. 2-6
Function Keys .................................................................. 2-7
Fn Key.............................................................................. 2-7
Hot Keys .......................................................................... 2-8
Using the Touchpad ........................................................... 2-12
Configuring the Touchpad ............................................. 2-14
Using the DVD Drive (Optional) ....................................... 2-15
Inserting and Removing a Disc ...................................... 2-15
Installing an Optical Drive Dummy (Optional) ............. 2-17
Using the Video Features ................................................... 2-19
Configuring the Display Modes ..................................... 2-19
Using the Audio Features ................................................... 2-20
Connecting Audio Devices ............................................ 2-21
Using the Communication Features ................................... 2-23
Using the LAN ............................................................... 2-23
Using the Wireless LAN ................................................ 2-24
Using the Bluetooth® Wireless Feature .......................... 2-27
Using the Fingerprint Sensor.............................................. 2-31
Managing Power......................................................................3-1
AC Adapter .......................................................................... 3-2
Battery Pack ......................................................................... 3-3
Charging the Battery Pack ............................................... 3-3
Initializing the Battery Pack............................................. 3-4
Checking the Battery Level.............................................. 3-5
Replacing the Battery Pack .............................................. 3-5
Installing a Second Battery Pack (Optional) .................... 3-7
Battery Low Signals and Actions..................................... 3-9
Power Management............................................................ 3-10
Hibernation..................................................................... 3-11
Power-Saving Tips ............................................................. 3-12
Expanding Your Computer.....................................................4-1
Connecting an External Monitor .......................................... 4-2
Connecting a USB Device.................................................... 4-3
Using ExpressCards ............................................................. 4-4
ExpressCard Type ............................................................ 4-4
ii
Inserting and Removing an ExpressCard ......................... 4-4
Using the Card Reader ......................................................... 4-6
Using the Port Replicator (Optional).................................... 4-8
Front Components............................................................ 4-8
Rear Components ............................................................. 4-9
System Memory Upgrade................................................... 4-12
Using BIOS Setup ...................................................................5-1
When and How to Use BIOS Setup ..................................... 5-2
When to Use..................................................................... 5-2
Starting BIOS Setup......................................................... 5-2
Moving Around and Making Selections .......................... 5-4
Main Menu ........................................................................... 5-5
Advanced Menu ................................................................... 5-6
Security Menu ...................................................................... 5-7
Boot Menu............................................................................ 5-9
Exit Menu........................................................................... 5-10
Installing Software Drivers and Using the P1 Utility ............6-1
How to Use the Driver Disc ................................................. 6-2
Installing Drivers.................................................................. 6-4
P1 Quick Button Utility........................................................ 6-6
Caring for the Computer.........................................................7-1
Protecting the Computer....................................................... 7-2
Using the Windows Security Center ................................ 7-2
Using the Cable Lock....................................................... 7-3
Taking Care of the Computer............................................... 7-4
Location Guidelines ......................................................... 7-4
General Guidelines........................................................... 7-4
Cleaning Guidelines ......................................................... 7-5
Battery Pack Guidelines ................................................... 7-5
When Traveling.................................................................... 7-6
Troubleshooting......................................................................8-1
Preliminary Checklist ........................................................... 8-2
iii
Solving Common Problems.................................................. 8-3
Battery Problems.............................................................. 8-4
Bluetooth Wireless Problems ........................................... 8-4
DVD Drive Problems ....................................................... 8-5
Display Problems ............................................................. 8-5
ExpressCard Problems ..................................................... 8-6
Hardware Device Problems.............................................. 8-7
Hard Disk Drive Problems ............................................... 8-7
Keyboard, Mouse, and Touchpad Problems .................... 8-8
LAN Problems ................................................................. 8-8
WLAN Problems.............................................................. 8-9
Power Management Problems........................................ 8-10
Software Problems ......................................................... 8-11
Sound Problems ............................................................. 8-11
Startup Problems ............................................................ 8-12
Other Problems............................................................... 8-13
Resetting the Computer ...................................................... 8-14
Specifications......................................................................... A-1
Regulatory Information.......................................................... B-1
On the Use of the System .....................................................B-2
Class B Regulations .........................................................B-2
Safety Notices ..................................................................B-3
On the Use of the RF Device................................................B-5
USA and Canada Safety Requirements and Notices........B-5
European Union CE Marking and Compliance Notices ..B-8
Index
iv
Preface
This manual contains information that will help you operate the
computer. It is divided into 8 chapters, 2 appendices, and an index.
Chapter 1, Getting Started, takes you through the process of setting
up the computer and identifying its external components.
Chapter 2, Operating Your Computer, tells you how to use the
computer’s components and features.
Chapter 3, Managing Power, provides information on power.
Chapter 4, Expanding Your Computer, provides information on
installing and using peripheral devices.
Chapter 5, Using BIOS Setup, describes the BIOS Setup program
that configures the computer’s BIOS settings.
Chapter 6, Installing Software Drivers and Using the P1 Utilities,
describes how to install the drivers and utilities supplied with the
computer, as well as how to use the P1 quick launch key utility.
Chapter 7, Caring for the Computer, gives you tips in care and
maintenance.
Chapter 8, Troubleshooting, gives solutions to common problems
you may encounter when using the computer.
Appendix A, Specifications, gives a brief specification of the
computer.
Appendix B, Regulatory Information, provides regulatory
statements and safety notices on your computer.
Notational Conventions
Throughout this manual, the following conventions are used to
distinguish elements of text.
NOTE: identifies additional information that requires special attention.
CAUTION: identifies important information that, if not followed, may result in loss of
data or damage to the computer.
Keyboard keys are shown in a bold typeset. For example:
Press the Enter key to complete.
When keys are joined by a plus sign (+), press the first key, and, while
keeping the first key down, press the remaining keys, finally release all
the keys. When necessary, keys are also shown in graphics.
A title, command, setup item, or button that you can see on the screen is
shown in boldface. A value or an option that you can select for a setup
item is shown in italic. For example:
Select When I press the power button, set it to Shut down, and
then click the Save changes button.
vi
Chapter 1
CHAPTER
Getting Started
Congratulations on purchasing this durable computer.
Your computer incorporates desktop computer capabilities into a
compact notebook-sized package. It can greatly enhance your
productivity either in the office or at home. And, of course, wherever you
need it, the computer is ready and easy “to go.”
This chapter first tells you step by step how to get the computer up and
running. You will find instructions for these procedures:
Unpacking
Connecting to AC power
Opening the cover
Turning on the computer
Turning off the computer
Then, you will find a section briefly introducing the external components
of the computer. And the last section navigates you to the information you
may need after the computer is ready for use.
Getting Started
1-1
Getting the Computer Running
This section guides you through the procedures for getting the computer
ready for operation.
Unpacking
After unpacking the shipping carton, you should find these standard
items:
Notebook computer
Accessories:
− AC adapter
− AC power cord
− Driver disc
Inspect all the items. If any item is damaged or missing, notify your dealer
immediately.
Keep the shipping carton and packing materials in case you need to ship
or store the computer in the future.
Connecting to AC Power
The computer operates either on the external AC power or internal battery
power. It is suggested that you use AC power when you start up the
computer for the very first time.
CAUTION: Use only the AC adapter included with your computer. Using other AC
adapters may damage the computer.
1. Make sure that the computer is turned off.
2. Plug the DC cord of the AC adapter to the power connector of the
computer ( ).
1-2
Getting Started
3. Plug the female end of the AC power cord to the AC adapter and the
male end to an electrical outlet ( ).
Push twice to insert thoroughly
4. When the AC adapter is connected, power is being supplied from the
electrical outlet to the AC adapter and onto your computer. Now, you
are ready to turn on the computer.
5. When the AC adapter is connected, it also charges the battery pack.
The Battery Charge Indicator on the computer glows amber to
indicate that charging is in progress. When the battery is fully
charged, the Battery Charge Indicator is off. (For information on
using battery power, see Chapter 3.)
CAUTION:
When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the computer. A reverse procedure may damage the AC adapter or the
computer.
When unplugging the connector, always hold the plug head. Never pull on the cord.
Getting Started
1-3
Opening the Cover
CAUTION: Be gentle when opening and closing the cover. Opening it vigorously or
slamming it shut could damage the computer.
Open the top cover by lifting up the cover. You can tilt the cover forward
or backward for optimal viewing clarity.
Turning On and Off the Computer
Turning On
1. Make sure that the computer is connected to AC power or the battery
is fully charged.
1-4
Getting Started
2. Press the power button.
3. Each time the computer is turned on, it performs a Power-On Self
Test (POST), and the Windows operating system should start.
Turning Off
To turn off the computer power, use the “Shut Down” command of your
operating system.
NOTE: There are other ways you can stop the computer so that you will be back to
where you left off when you next turn on the computer. (See “Stopping the Computer” in
Chapter 2 for information.)
CAUTION: If you have to turn the computer on again immediately after turning it off,
wait for at least five seconds. Turning the computer off and on rapidly can damage it.
Getting Started
1-5
Taking a Look at the Computer
This section identifies the external components of the computer and
briefly describes the function of each component.
NOTE: Depending on the model you purchased, the appearance of your computer may
not be exactly the same as those shown in this manual.
Right-Side Components
Ref
Component
Description
ExpressCard Slot Accepts an ExpressCard for additional
functions.
P. 4-4
Swappable Bay
Depending on your model, the swappable bay
may contain any of the following:
DVD Super
Multi Drive
Accepts a compact disc for installing or
loading software, accessing data, and playing
music/video.
Secondary
Battery Pack
Supplies power to your computer when
external power is not connected.
Optical Drive
Dummy
Install an optical drive dummy if you do not
plan to use the optical drive for a length of
time or to lighten the computer during
transport.
P. 2-17
USB Port
Connects a USB device, such as a flash disk,
printer, digital camera, joystick, and more.
P. 4-3
Power Connector Connects the AC adapter.
1-6
See Also
P. 2-14
P. 3-7
P. 1-2
Getting Started
Left-Side Components
Ref
Component
Description
Kensington Lock Locks the computer to a stationery object for
security.
See Also
P. 7-3
VGA Connector
Connects an external display.
P. 4-2
Expansion Bus
Connector
Connects to a Port Replicator.
P. 4-8
RJ-45 Connector Connects the LAN cable.
P. 2-23
USB Ports
Each of the two ports connects a USB device,
such as a flash disk, printer, digital camera,
joystick, and more.
Microphone
Connector
Connects an external microphone.
P. 2-21
Audio Output
Connector
Connects a set of headphones, external
speakers with amplifier, or an audio recording
device.
P. 2-21
S/PDIF
Connector
Connects an S/PDIF device such as a digital
speaker set for digital audio output.
P. 2-21
RF (radio
frequency)
On/Off Switch
Serves as the master switch that allows you to
turn the wireless LAN radio and Bluetooth
wireless feature.
Getting Started
P. 4-3
P. 2-24,
2-27, 錯
誤! 尚未
定義書
籤。
1-7
Front Components
Ref
Component
Card Reader
1-8
Description
Accepts a MultiMediaCard (MMC), Secure
Digital (SD), Memory Stick (MS) or Memory
Stick PRO (MS PRO) card for removable
storage media.
See Also
P. 4-6
Getting Started
Bottom Components
Ref
Component
Description
See Also
Battery Pack
Supplies power to your computer when
external power is not connected.
Memory Slot
Inside is the memory slot for expanding the
memory size.
P. 4-12
Speakers
Sends out sound and voice from the
computer.
P. 2-20
Getting Started
P. 3-3
1-9
Top-open Components
Ref
1-10
Component
Description
See Also
Microphone
Receives sound and voice for the computer.
P. 2-20
CMOS Camera
Lens
Allows you to use your computer’s camera
function.
LCD Screen
Displays the output of the computer.
P. 4-2
Power Button
Turns the computer power ON and OFF.
P. 1-4
Keyboard
Serves as the data input device of the computer.
P. 2-5
Touchpad
Serves as the pointing device of the computer.
P. 2-12
Getting Started
Ref
Component
Description
See Also
Quick Buttons
Enables/disables power saving when using
battery power.
P. 2-4
Microsoft® Internet Explorer quick launch key.
P. 2-4
P1 (Program 1 – user customized) quick launch
key.
P. 2-27
Fingerprint
Sensor
Serves as the fingerprint verification,
preventing unauthorized access to your
computer.
P. 2-31
Indicators
Show the current status of the computer’s
devices.
WLAN /
Bluetooth®
indicator
Lights blue when WLAN radio is on.
P1
AC / Battery
Power indicator
®
Lights red when Bluetooth feature is on.
P. 2-24
P. 2-27
Lights purple when both WLAN radio and
Bluetooth® feature is on.
Lights blue when computer is on and connected
to AC power.
P. 1-4
Lights amber when computer is on and using
battery power.
Blinks blue when computer is in Sleep mode.
Battery charge
indicator
Lights blue when the battery is charged.
P. 3-3
Lights amber when the battery is being charged.
Blinks red when the battery’s capacity is below
10 %.
Hard disk drive
in-use indicator
Blinks blue when computer is accessing the
hard disk drive.
Caps Lock
indicator
Lights blue when Caps Lock is on.
Getting Started
P. 2-14
P. 2-5
1-11
Ref
Component
Num Lock
indicator
1-12
Description
Lights blue when Num Lock is on.
See Also
P. 2-5
Getting Started
Where to Go from Here
As your computer is ready for operation, you may want to do any of the
following now:
For this purpose...
To know more about the computer...
Do this...
Go on to the next chapter.
To install the operating system if your See the operating system manual.
dealer has not already done so...
To know more about the operating
system...
Read the operating system manual.
To install the drivers if your dealer has See Chapter 6.
not already done so...
To charge the battery pack for the first See “Charging the Battery Pack” in
time...
Chapter 3.
Getting Started
1-13
Chapter 2
CHAPTER
Operating Your Computer
This chapter provides information about the use of the computer.
If you are new to computers, reading this chapter will help you learn the
operating basics. If you are already a computer user but are new to
notebook computers, you may choose to read only the parts containing
information unique to your computer.
Described in this chapter are the operating basics of these components:
Starting and stopping the computer
Quick buttons
Keyboard
Touchpad
DVD drive
Video features
Audio features
Communication features
Fingerprint sensor
Operating Your Computer
2-1
Starting and Stopping the Computer
There are a number of ways to start and stop the computer.
Starting the Computer
You always start the computer using the power button.
A computer starts up with an operating system (OS) existing on the
storage device such as the hard disk and optical disc. The computer will
automatically load the OS after you turn it on. This process is called
booting.
NOTE: An operating system is the platform for all your software application programs to
run on. Your computer uses the Microsoft Windows Vista operating system.
Stopping the Computer
When you finish a working session, you can stop the computer by turning
off the power or leaving the computer in Sleep or Hibernation mode:
To stop in
this mode...
Off
Do this...
To start up or
resume again
Click Start Shut Down … . This can
prevent loss of unsaved data or damage to
your software programs.
Press the power
button.
If the system is locked up because of
hardware or software problems, press the
power button to turn off the computer.
Sleep
2-2
Depending on your settings in Windows,
you can place the computer in Sleep
mode by:
• Closing the display cover
• Pressing the Fn+F12 hot key
• Pressing the power button
Press any key.
Operating Your Computer
To stop in
this mode...
Hibernation
Do this...
To start up or
resume again
Depending on your settings in Windows,
you can place the computer in
Hibernation mode by:
• Closing the display cover
• Pressing the power button
Press the power
button.
If you choose to stop in Sleep or Hibernation mode, you can return to
where you left off the next time you start up the computer. (See “Power
Management” in Chapter 3 for more information.)
Operating Your Computer
2-3
Using the Quick Buttons
The Quick buttons are three pre-defined buttons located on the left above
the keyboard.
The Easy Start buttons allow you to start the frequently-used programs
with one single press of a button (from left to right):
Enter into power saving mode when using battery power.
The system will turn down the panel backlight and sacrifice
processing speed to gain more battery life.
NOTE:
The ECO button works only when using battery power.
Upon connecting AC power when in ECO mode, your computer will return to
previous state before power saving mode.
Microsoft® Internet Explorer
P1
2-4
P1 (Program 1 – user customized) quick launch key
(see chapter 6 for details)
Operating Your Computer
Using the Keyboard
Your keyboard has all the standard functions of a full-sized computer
keyboard plus a Fn key added for specific functions.
The standard functions of the keyboard can be further divided into four
major categories:
Typewriter keys
Cursor-control keys
Numeric keys
Function keys
Typewriter Keys
Typewriter keys are similar to the keys on a typewriter. Several keys are
added such as the Ctrl, Alt, Esc, and lock keys for special purposes. When
the lock keys (Caps Lock, Num Lk, and Scr Lk) are pressed, their
corresponding indicators light up.
The Control (Ctrl) / Alternate (Alt) key is normally used in combination
with other keys for program-specific functions. The Escape (Esc) key is
usually used for stopping a process. Examples are exiting a program and
canceling a command. The function depends on the program you are
using.
Operating Your Computer
2-5
Cursor-Control Keys
NOTE: The word “cursor” refers to the indicator on the screen that lets you know
exactly where on your screen anything you type will appear. It can take the form of a
vertical or horizontal line, a block, or one of many other shapes.
Numeric Keypad
A 15-key numeric keypad is embedded in the typewriter keys as shown
next:
2-6
Operating Your Computer
Numeric keys facilitate entering of numbers and calculations. When Num
Lock is on, the numeric keys are activated; meaning you can use these
keys to enter numerals.
NOTE:
When the numeric keypad is activated and you need to type the English letter in the
keypad area, you can turn Num Lock off or you can press Fn and then the letter
without turning Num Lock off.
Some software may not be able to use the numeric keypad on the computer. If so,
use the numeric keypad on an external keyboard instead.
Function Keys
On the top row of the keys are the function keys: F1 to F12. Function keys
are multi-purpose keys that perform functions defined by individual
programs.
Fn Key
The Fn key, at the lower left corner of the keyboard, is used with another
key to perform the alternative function of a key. The letter “Fn” and the
alternative functions are identified by the color of blue on the keytop. To
perform a desired function, first press and hold Fn, then press the other
key.
Operating Your Computer
2-7
Hot Keys
Hot keys refer to a combination of keys that can be pressed any time to
activate special functions of the computer. Most hot keys operate in a
cyclic way. Each time a hot key combination is pressed, it shifts the
corresponding function to the other or next choice.
You can easily identify the hot keys with the icons imprinted on the
keytop. The hot keys are described next.
Key
Description
Switches the wireless LAN radio and/or Bluetooth® wireless
feature on and off.
NOTE: Refer to the next table for the behavior of Fn+F1 key in
relation to the availability of the wireless LAN module and/or
Bluetooth® module in your computer.
Decreases the sound volume.
Increases the sound volume.
Switches the display output to one of the following when
external devices are connected.
Upon booting the system with CRT:
NOTE: This function only applies to Plug & Play display
devices.
Decreases the LCD brightness.
Increases the LCD brightness.
Switches the touchpad off and on (depending on your model).
Switches the system sound output off (mute) and on.
2-8
Operating Your Computer
Key
Description
Switches LCD display on and off.
Serves as the sleep button that you can define with Windows’
Power Options. (See the “Power Management” in Chapter 3.)
Operating Your Computer
2-9
Fn+F1 Behavior
The following table shows the behavior of Fn+F1 key in relation to the
availability of the wireless LAN module and/or Bluetooth® module in
your computer.
NOTE: Make sure that RF switch is at the ON position.
Available Module
Upon pressing Fn+F1 key . . .
Wireless LAN
Bluetooth
Wireless LAN (only)
Default: wireless LAN
radio is ON.
OFF
N/A
(not available)
Bluetooth® (only)
Default: Bluetooth®
wireless feature is OFF.
N/A
ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
Wireless LAN +
Bluetooth®
Default: wireless LAN
radio is ON, Bluetooth®
wireless feature is OFF.
Wireless LAN +
Bluetooth®
Default: wireless LAN
radio is ON, Bluetooth®
wireless feature is OFF.
NOTE: Upon restarting your computer or upon waking up from Sleep mode, the system
will resume Fn+F1 behavior based on the last state.
Euro Symbol
You can press the euro dollar sign
2-10
on various keyboards.
Operating Your Computer
To press the euro sign on a United States-International keyboard, hold
down the Alt Gr key and press 5 (which has an euro sign on it).
To press the euro sign on a standard United States keyboard, hold
down either of the Alt keys and type 0128 on the numeric keypad part
of your keyboard.
To press the euro sign on an UK keyboard, hold down the Alt Gr key
and press 4 (which has an euro sign on it).
Windows Keys
The keyboard has two keys that perform Windows-specific functions:
Windows Logo key and
Application key.
Windows Logo key opens the Start menu and performs
The
software-specific functions when used in combination with other keys.
Application key usually has the same effect as a right mouse
The
click. (See your Windows manual for more information.)
Operating Your Computer
2-11
Using the Touchpad
CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may
damage the touchpad surface.
NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean
and dry. When tapping on the pad, tap lightly. Do not use excessive force.
The touchpad is a pointing device that allows you to communicate with
the computer by controlling the location of the pointer on the screen and
making selection with the buttons.
The touchpad consists of a rectangular pad and a left and right buttons. To
use the touchpad, place your forefinger or thumb on the pad. The
rectangular pad acts like a miniature duplicate of your display. As you
slide your fingertip across the pad, the pointer (also called cursor) on the
screen moves accordingly. When your finger reaches the edge of the pad,
simply relocate yourself by lifting the finger and placing it on the other
side of the pad.
2-12
Operating Your Computer
Here are some common terms that you should know when using the
touchpad:
Term
Action
Point
Move your finger on the pad until the cursor points to the
selection on the screen.
Click
Press and release the left button.
–or–
Tap gently anywhere on the pad.
Double-click
Press and release the left button twice in quick succession.
–or–
Tap twice on the pad rapidly.
Drag and
drop
Press and hold the left button, then move your finger until
you reach your destination (drag). Finally, release the
button (drop) when you finish dragging your selection to
the destination. The object will drop into the new location.
–or–
Gently tap twice on the pad and on the second tap, keep
your finger in contact with the pad. Then, move your
finger across the pad to drag the selected object to your
destination. When you lift your finger from the pad, the
selected object will drop into place.
Scroll
To scroll is to move up and down or left and right in the
working area on the screen.
To move vertically, place your finger on the right or left
edge of the pad and slide your finger up and down along
the edge. To move horizontally, place your finger on the
top or bottom edge of the pad and slide your finger left and
right.
This function works only after you install the touchpad
driver supplied with the computer and it may not work for
all applications.
TABLE NOTE: If you swap the left and right buttons, “tapping” on the touchpad
as an alternative method of pressing the left button will no longer be valid.
Operating Your Computer
2-13
Configuring the Touchpad
You may want to configure the touchpad to suit your needs. For example,
if you are a left-handed user, you can swap the two buttons so that you can
use the right button as the left button and vice versa. You can also change
the size of the on-screen pointer, the speed of the pointer, and so on.
To configure the touchpad, go to Control Panel Hardware and Sounds
Mouse Properties. However, you can install the touchpad driver
supplied with your computer to take advantage of more powerful
features. (For information on installing the driver, see “How to Use the
Driver Disc” in Chapter 6.)
2-14
Operating Your Computer
Using the DVD Drive (Optional)
Depending on the model your computer’s swappable bay may contain a
DVD drive, usually configured as drive D. The Super Multi drive can
work both as a DVD-ROM drive for reading DVD (Digital Versatile
Disc) discs in addition to CDs, audio CDs and CD-R/-RW discs, and
CD-RW drive. Can also write to DVD+R/+RW/-R/-RW/DVD-RAM
discs.
CAUTION:
When inserting a disc, do not use force.
Make sure that the disc is correctly inserted into the tray, and then close the tray.
Do not leave the DVD tray open. Also, avoid touching the lens in the tray with your
hand. If the lens becomes dirty, the DVD drive may malfunction.
Do not wipe the lens using materials with rough surface (such as paper towel).
Instead, use a cotton swab to gently wipe the lens.
FDA regulations require the following statement for all laser-based devices:
“Caution, Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.”
NOTE: The DVD drive is classified as a Class 1 laser product. This label is located on
the DVD drive.
NOTE: For DVD and Combo drives only.
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Inserting and Removing a Disc
Follow this procedure to insert or remove a disc:
1. Turn on the computer.
Operating Your Computer
2-15
2. Press the eject button and the DVD tray will slide out partially.
Gently pull on it until it is fully extended.
3. To insert a disc, place down the disc in the tray with its label facing
up. Slightly press the center of the disc until it clicks into place.
Eject button
In-use indicator
To remove a disc, hold the disc by its outer edge and lift it up from the
tray.
4. Gently push the tray back into the drive.
NOTE: In the unlikely event that you are unable to release the DVD tray by pressing the
eject button, you can manually release the disc. (See “Optical Drive Problems” in
Chapter 8.)
2-16
Operating Your Computer
Installing an Optical Drive Dummy (Optional)
You can install an optical drive dummy in place of the optical drive if you
do not plan to use it for a length of time or to lighten the computer during
transport. To install an optical drive dummy:
1. Make sure that system power is off.
2. Gently place the computer upside down.
3. Slide the swappable bay release lever outward to the unlock ( )
position ( ) and, while holding it in the unlock position, pull the
optical drive off the computer ( ).
Operating Your Computer
2-17
4. Slide the optical drive dummy all the way into the slot. Make sure to
observe the correct orientation. The swappable bay security lock will
slide to the lock ( ) position to secure the optical drive dummy.
2-18
Operating Your Computer
Using the Video Features
The video subsystem of your computer features:
13.3-inch TFT (Thin-Film Transistor) color LCD display with
1280×800 WXGA resolution
Simultaneous display on LCD and external display, which is useful
when you have a presentation as you can control the screen from your
computer and face the audience at the same time.
Multi-display capability, which allows you to expand your desktop
on the screen to another display device so that you have more desktop
space to work on.
Power Management
NOTE:
Before using the multi-display capability or taking advantage of the enhanced video
capabilities, the VGA driver supplied with your computer must be installed. (See
chapter 6 for details.)
The computer enters the Sleep or Hibernation mode when the LCD is closed.
If you want to use the computer with the LCD closed, set Do Nothing to the “When I
Close the lid” option in the Power Options System Settings Properties.
Thus the computer does not enter the Sleep or Hibernation mode when the LCD is
closed.
Configuring the Display Modes
NOTE: When using an external CRT monitor, the resolution depends on the CRT
monitor’s supported resolution.
Your computer has been set to a default resolution and number of colors
before shipment. You can view and change display settings through your
operating system. See your operating system documentation or online
help for specific information.
For displaying in higher resolutions, you can connect an external monitor
that supports higher resolutions. (See “Connecting an External Monitor”
in Chapter 4 for more information.)
Operating Your Computer
2-19
Using the Audio Features
NOTE:
To take advantage of the enhanced audio capabilities, the audio driver supplied
with your computer must be installed. (See chapter 6 for details.)
If you experience interference while recording, try lowering the microphone
recording volume.
The audio subsystem of your computer features:
Built-in sound system for recording and playing sound on your
computer
Azalia interface (high density audio codec)
2.1-channel analog output
Built-in microphone ( )
External audio connectors ( ), and
Set of speakers ( )
2-20
Operating Your Computer
Ways of playing and recording sound vary with the operating system
used. See your operating system documentation or online help for
specific information.
Connecting Audio Devices
For higher audio quality, you can send or receive sound through external
audio devices.
NOTE: After connecting an external audio device, make sure that you specify the use of
the correct audio device in Windows.
Microphone Connector (
) can be connected to an external
microphone for recording voice or sound.
Audio Output Connector (
headphones, or earphone set.
) can be connected to speakers,
S/PDIF Connector ( S/PDIF ) can be connected to the line-in
connector of S/PDIF (Sony/Philips Digital InterFace) compliant as
well as ordinary powered speakers with built-in amplifiers,
headphones, or earphone set. S/PDIF is an audio transfer file format
that ensures a high quality digital audio output through optical fibers.
Operating Your Computer
2-21
NOTE:
The S/PDIF connector is classified as a Class 1 laser product.
When using the external speakers/headphones or microphone, you cannot use the
internal one.
2-22
Operating Your Computer
Using the Communication Features
Using the LAN
NOTE: To take advantage of the LAN feature, the LAN driver supplied with your
computer must be installed. (See chapter 6 for details.)
The internal 10/100/1000Base-T LAN (Local Area Network) module
allows you to connect your computer to a network. It supports data
transfer rate up to 1000 Mbps.
To connect the network cable to the LAN module, connect one end of the
LAN cable to the RJ-45 connector on the computer and the other end to
the network hub.
Operating Your Computer
2-23
Using the Wireless LAN
Depending on your model, an internal mini PCI-E wireless LAN
(WLAN) card may have been pre-installed by your computer
manufacturer at the factory. This card allows you to access corporate
networks or the Internet in a wireless environment.
The WLAN features include:
Access Point (Infrastructure) mode support
WEP (Wired Equivalent Privacy) 64/128-bit data encryption
IEEE 802.11b/g/n standard compliance
Stated
Maximum
Technology Throughput Data Rates Band (GHz)
(Mbps)
(Mbps)
Modulation Technology
802.11b
11
11, 5.5, 2, 1 2.4
DSSS (Direct Sequence Spread
Spectrum)
802.11g
54
54, 36, 18,
2.4
OFDM (Orthogonal Frequency
Division Multiplexing)
802.11n
100 Mbps or
more
100 ~ 210
2.4 / 5
Spatial multiplexing, uses MIMO
(multiple-input multiple-output)
To take advantage of the WLAN feature, make sure that the WLAN
driver is installed correctly. (See chapter 6 for details.) If your WLAN
card was provided by your dealer instead of the computer manufacturer,
contact your dealer for the correct driver to use.
Turning Off/On the WLAN Radio
NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless
devices in aircraft as this may interfere with flight safety. Remember to turn off wireless
LAN when using your computer in the airplane.
2-24
Operating Your Computer
To turn on the WLAN radio:
1. Make sure that the RF switch is at the ON position.
2. Press Fn+F1 to turn on the WLAN radio (see “Fn+F1 Behavior” in
Chapter 2), indicated by the WLAN indicator (
) glowing in blue
when on.
If you need to temporarily turn off the radio, press Fn+F1. To resume
network connection, press Fn+F1 again.
It takes approximately 30 seconds for your computer to make a successful
WLAN connection and approximately 10 seconds to disconnect.
Connecting to a Wireless Network
To connect to a wireless network:
1. Make sure that the WLAN radio is on (see the previous section).
2. Right-click the Wireless Network Connection icon
located on the
Windows system tray and select Connect to a network.
Operating Your Computer
2-25
3. If any wireless network is detected, the following window appears on
screen. Click the Show drop down menu and select Wireless.
4. Select a wireless network to connect to by clicking a selection, then
click Connect.
5. Depending on the settings, you may be asked to enter a WEP key
(refer to your Windows online help for more information on setting a
wireless network connection).
2-26
Operating Your Computer
Using the Bluetooth® Wireless Feature
NOTE: To take advantage of the Bluetooth feature, the Bluetooth driver supplied with
your computer must be installed. (See chapter 6 for details.)
Depending on your model, your computer may incorporate the Bluetooth
capability for short-range (about 10 meters) wireless communications
between devices without requiring a cable connection.
With Bluetooth, data can be transmitted through walls, pockets and
briefcases as long as two devices are within range.
Turning On and Off the Bluetooth Feature
NOTE:
You can still use the WLAN feature when the Bluetooth feature is turned on.
The wireless LAN indicator (
) will glow in purple when both wireless LAN and
Bluetooth feature are turned on.
1. Make sure that the RF switch is at the ON position.
2. Press Fn+F1 to turn the Bluetooth® wireless feature on (see “Fn+F1
Behavior” in Chapter 2).
) will glow in red. By default, your
The wireless LAN indicator (
computer is in the general discoverable and pairable mode after the
Bluetooth feature is turned on.
3. To turn off the Bluetooth feature, press Fn+F1 again.
Operating Your Computer
2-27
The status of the Bluetooth connection is indicated by the Bluetooth icon
located in the system tray in the lower-right part of the screen.
Status
Icon
Off
®
On
®
Connected
®
(blue with red logo)
(blue with white logo).
(blue with green logo)
You can use the Bluetooth Utility to configure Bluetooth connection
settings and transfer files.
Connecting to Another Bluetooth Device
1. Make sure that the target Bluetooth device is turned on, discoverable
and within close range. (See the documentation that came with the
Bluetooth device.)
2. Right-click the
2-28
icon, and then click Add New Connection.
Operating Your Computer
3. The Add New Connection Wizard window appears. Select Express
Mode (Recommended), then click Next.
Operating Your Computer
2-29
4. Select the device to connect to and click Next.
5. Depending on the type of Bluetooth device that you want to connect
to, you will need to enter the pertinent information.
For detailed information on using the Bluetooth Utility, see the Bluetooth
Utility Help on your computer by clicking Help, then Contents and Index.
2-30
Operating Your Computer
Using the Fingerprint Sensor
NOTE: To take advantage of the fingerprint sensor, the fingerprint driver supplied with
your computer must be installed. (See chapter 6 for details.)
To start using the fingerprint sensor:
1. Locate the fingerprint sensor.
2. Go to Start menu
System Settings.
All Programs
VitaKey
AC5031
System
NOTE: You must first complete the System Wizard before you can utilize the VitaKey
utlity. The following screen appears.
Operating Your Computer
2-31
3. Click Next to continue and the following screen appears.
2-32
Operating Your Computer
4. Select Create new user data file and click Next to continue. The
following screen appears.
5. Enter the password twice and click Next to continue. Follow the
onscreen instructions to complete the System Wizard.
NOTE: For an online Help information on using the VitaKey utility, you can go to Start
menu All Programs VitaKey AC5031 Online Help.
Operating Your Computer
2-33
Chapter 3
CHAPTER
Managing Power
Your computer operates either on external AC power or on internal
battery power.
This chapter tells you how you can effectively manage power. To
maintain optimal battery performance, it is important that you use the
battery in the proper way.
The topics in this chapter include:
What is an AC adapter
How to charge the battery pack
When and how to initialize the battery pack
How to check the battery level
How to replace the battery pack
What happens when the battery is low and what actions to take
What is Power Management
How to save power
Managing Power
3-1
AC Adapter
CAUTION:
The AC adapter is designed for use with your computer only. Connecting the AC
adapter to another device can damage the adapter.
The AC power cord supplied with your computer is for use in the country where you
purchased your computer. If you plan to go overseas with the computer, consult
your dealer for the appropriate power cord.
When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the computer. A reverse procedure may damage the AC adapter or
computer.
When unplugging the connector, always hold the plug head. Never pull on the cord.
The AC adapter serves as a converter from AC (Alternating Current) to
DC (Direct Current) power because your computer runs on DC power,
but an electrical outlet usually provides AC power. It also charges the
battery pack when connected to AC power.
The adapter operates on any voltage in the range of 100~240 V AC.
3-2
Managing Power
Battery Pack
The battery pack is the internal power source for the computer. It is
rechargeable using the AC adapter.
The operating time of a fully charged battery pack depends on how you
are using the computer. When your applications often access peripherals,
you will experience a shorter operating time.
NOTE: Care and maintenance information for the battery is provided in the “Battery
Pack Guidelines” section in Chapter 7.
Charging the Battery Pack
NOTE:
Charging will not start if the battery’s temperature is below 0 °C (32 °F) or above
45 °C (113 °F).
The charging process will stop and the Battery Charge Indicator flashes red when
the battery’s temperature gets above 60 °C (140 °F). If this happens, the battery
pack may be damaged. Please contact your dealer.
During charging, do not disconnect the AC adapter before the battery has been fully
charged; otherwise you will get a prematurely charged battery.
To charge the battery pack, connect the AC adapter to the computer and
) on the
an electrical outlet. The Battery Charge Indicator (
computer glows amber to indicate that charging is in progress. You are
advised to keep the computer power off while the battery is being
charged. When the battery is fully charged, the Battery Charge Indicator
is off.
Managing Power
3-3
The charging times are as follows:
Charging Time
Battery Type
Computer is Off
Computer is On and
in Idle State
3-cell
(2600 mAH)
3 hours
3.5 hours
6-cell
(5200 mAH)
4 hours
4.5 hours
Second battery pack
(in swappable bay)
3.5 hours
4 hours
CAUTION: After the computer has been fully recharged, do not immediately disconnect
and reconnect the AC adapter to charge it again. Doing so may damage the battery.
NOTE: The battery level may automatically lessen due to the self-discharge process
(0.21 % per day), even when the battery pack is fully charged (100 %). This happens no
matter if the battery pack is installed in the computer.
Initializing the Battery Pack
You need to initialize a new battery pack before using it for the first time
or when the actual operating time of a battery pack is much less than
expected.
Initializing is the process of fully charging, discharging, and then
charging. It can take several hours.
1. Make sure that the computer power is turned off. Connect the AC
adapter to fully charge the battery pack.
2. After the battery pack is fully charged, turn on the computer. When
the message “Press F2 for System Utilities” appears, press
the F2 key to invoke the program.
3. Disconnect the AC adapter and leave the computer on until the
battery is fully discharged. The computer will shut down
automatically.
4. Connect the AC adapter to fully charge the battery pack.
3-4
Managing Power
Checking the Battery Level
NOTE: Any battery level indication is an estimated result. The actual operating time can
be different from the estimated time, depending on how you are using the computer.
By Operating System
You can check the approximate battery level using the battery meter
function of the operating system. To read the battery level, click the
icon on the system tray.
By Gas Gauge
On the exterior side of the battery pack is a gas gauge for displaying the
estimated battery charge. When the battery pack is not installed in the
computer and you want to know the battery charge, you can press the
switch with a pointed device to see the corresponding value of indicator
segment that light green. The value of the corresponding green segment
indicates the relative percentage of the battery charge. The battery pack is
fully discharged when you see no segment glowing green.
Switch
Replacing the Battery Pack
CAUTION:
There is danger of explosion if the battery is incorrectly replaced. Replace the
battery only with the computer manufacturer’s optional battery packs. Discard used
batteries according to the dealer’s instructions.
Do not attempt to disassemble the battery pack.
Managing Power
3-5
If you often rely on battery power for a long period of time while
traveling, you may consider the purchase of an additional battery pack
from your dealer and keep it with you in a fully charged state as a backup.
To replace the battery pack, follow these steps:
1. Make sure that the computer is not turned on or connected to AC
power.
2. Place the computer upside down.
3. Slide the battery security lock outward to the unlock (
( ).
) position
4. Slide the battery release lever outward to the unlock ( ) position
( ) and, while holding it in the unlock position, remove the battery
pack off the computer ( ).
3-6
Managing Power
5. Fit another battery pack into place ( ) and slide the battery security
lock to the lock ( ) position ( ).
Installing a Second Battery Pack (Optional)
You can install a second battery pack to your computer for a longer
operating time when AC power is not available. To install a second
battery pack:
1. Make sure that system power is off.
2. Gently place the computer upside down.
Managing Power
3-7
3. Slide the swappable bay release lever outward to the unlock ( )
position ( ) and, while holding it in the unlock position, pull the
optical drive off the computer ( ).
4. Slide the second battery pack all the way into the slot. Make sure to
observe the correct orientation. The swappable bay security lock
would slide to the lock ( ) position to secure the second battery
pack.
3-8
Managing Power
Battery Low Signals and Actions
The battery icon changes appearance to display the current state of the
battery so that you can see how much charge remains (Windows default
setting). When the battery charge is above 25 % the battery icon is green.
When the battery charge reaches 25 % a yellow triangle with an
exclamation point (!) appears above the green battery icon. When the
charge reaches the low battery level a red circle with a white “X” appears
above the green icon. The computer’s Battery Charge Indicator (
blinks red to alert you to take actions.
Immediately save your data upon Battery Low. The remaining operating
time depends on how you are using the computer. If you are using the
audio subsystem, ExpressCard, hard or USB flash disk, the battery might
run out of charge very quickly.
Always respond to Battery Low by placing your computer on Hibernation
mode, turning off the computer, or connecting the AC adapter.
CAUTION:
If you are using an ExpressCard, do not access the card during battery low periods.
This is because the access may take longer than the time it takes the battery to run
out of charge, thus making your access to the card unsuccessful.
If you fail to save your data when the battery completely runs out of charge, then
you lose your data.
Managing Power
3-9
Power Management
Your computer supports ACPI (Advanced Configuration and Power
Interface) for power management. The power management feature allows
you to reduce the power consumption for energy saving.
With an ACPI-compliant operating system such as Windows, power
supply to different computer components is controlled on an as-needed
basis. This allows maximum power conservation and performance at the
same time.
In general, Windows’ power management works in this way:
What...
When...
Power to the hard disk is turned off
When the hard disk has been idle for a
set period.
Power to the display is turned off
When the display has been idle for a
set period.
The computer enters the Sleep mode.
The hard disk and display are turned
off and the entire system consumes
less power.
When the entire system has been idle
for a set period.
When you press the Fn+F12 hot key. *
When you close the cover. *
When you press the power button. *
The computer enters the Hibernation
mode. (See the next subsection for
more information.)
When the entire system has been idle
for a set period.
When you press the Fn+F12 hot key. *
When you close the cover. *
When you press the power button. *
* Depends on your settings in Windows.
For detailed information on power management, see Windows’ Help.
3-10
Managing Power
Hibernation
NOTE: Make sure that the hibernation feature is enabled in the “When I press the
power button,” “When I press the sleep button,” and “When I close the lid” of the Power
Options System Settings Properties from the Control Panel Mobile PC.
Hibernation is a very useful feature. People frequently open many
applications when they use computers. It takes some time to get all these
applications open and running, and normally they all have to be closed
before the computer can be turned off.
When you use the hibernation feature, you do not have to close the
applications. The computer stores the state of your computer to a file on
the hard disk and then shuts down. The next time you turn on your
computer, you return to exactly where you left off.
Managing Power
3-11
Power-Saving Tips
Aside from enabling your computer’s power saving mode (see previous
section), you can do your part to maximize the battery’s operating time by
following these suggestions.
Do not disable Power Management. Choose a power plan that saves
power. A power plan is a collection of hardware and system settings
that control how your computer manages power.
Decrease the LCD brightness to the lowest comfortable level.
Shorten the length of time before Windows turn off the display.
Many USB devices use power just by being connected. If you use a
USB mouse, you can save power by disconnecting the mouse and
using the touchpad. If you use a USB flash drive, unplug it when you
are not using it.
If you work with an application that uses an ExpressCard, exit the
application when you finish using it.
If you have an ExpressCard installed, remove it when not in use.
Some ExpressCards drain power even while they are inactive.
Deactivate the wireless LAN function if you are not using it.
(See Chapter 2.)
Deactivate the Bluetooth® wireless function if you are not using it.
(See Chapter 2.)
Turn off the computer when you are not using it.
3-12
Managing Power
Chapter 4
CHAPTER
Expanding Your Computer
You can expand the capabilities of your computer by connecting other
peripheral devices. When using a device, be sure to read the instructions
accompanying the device together with the relevant section in this
chapter.
This chapter gives guidelines on installing and using these devices:
External monitor
USB device
ExpressCard
Card Reader
Port Replicator
System memory
Expanding Your Computer
4-1
Connecting an External Monitor
If you want the benefits of a larger display screen with higher resolution,
you can connect an external CRT monitor or LCD monitor to your
computer. Follow this procedure to connect an external monitor:
1. Make sure that the computer is not turned on.
2. Plug the monitor’s signal connector to the computer’s VGA
connector.
3. Plug one end of the monitor’s power cord into the power socket on
the monitor and the other end to an electrical outlet.
4. To use the monitor, turn on the monitor before turning on the
computer.
5. The monitor should respond by default. If not, you can switch the
display to the monitor or to both (simultaneous display), or to
multi-display by pressing the Fn+F5 hot key. You can also change the
display through the Display Settings Properties.
6. You can change display settings through your operating system. See
your operating system documentation or online help for specific
information.
CAUTION: Do not disconnect the external monitor while the computer is in the Sleep
mode or Hibernation mode. If no external monitor is connected when the computer
resumes, the LCD might not display properly.
4-2
Expanding Your Computer
Connecting a USB Device
Your computer has three USB ports for connecting USB devices, such as
a digital camera, scanner, printer, modem, and mouse.
The USB ports support transfer rates up to 12 MB/s for USB 1.1 devices
and 480 MB/s for USB 2.0 devices.
To connect a USB device, simply plug the device cable to one of the USB
ports.
Expanding Your Computer
4-3
Using ExpressCards
NOTE: The ExpressCard interface is not compatible with the PC card interface. You
need optional adapters for using PC cards on your computer.
Your computer has an ExpressCard slot.
ExpressCard supports the PCI Express and USB 2.0 serial data interfaces
(supporting speeds of up to 2.5 Gbps and 480 Mbps respectively),
improving speed in data transfer while conserving power usage.
ExpressCard Type
The ExpressCard slot can accommodate a 34 mm (ExpressCard/34) wide
ExpressCard. Typical ExpressCards support a very extensive range of
applications including memory, wired and wireless communication cards,
and security devices.
Shown next is the appearance of ExpressCard/34 for your reference.
Inserting and Removing an ExpressCard
To insert an ExpressCard:
1. Locate the ExpressCard slot on the computer.
4-4
Expanding Your Computer
2. Press the cover tray ( ) and pull it out ( ).
3. Slide the ExpressCard, with its label facing up, all the way into the
slot until the rear connectors click into place.
4. When a new card is seated, the computer will detect it and try to install
the appropriate driver. Follow the on-screen instructions to complete
the process.
To remove an ExpressCard:
found on the
1. Double-click the Safely Remove Hardware icon
Windows system tray and the Safely Remove Hardware window
appears on screen.
2. Select (highlight) the ExpressCard from the list to disable the card.
3. Push the ExpressCard slightly to release the card.
4. Pull the card out of the slot.
Expanding Your Computer
4-5
Using the Card Reader
NOTE:
To take advantage of the Card Reader, the Card Reader driver supplied with your
computer must be installed. (See chapter 6 for details.)
If your hard disk is divided into several drives, make sure that all drives have been
formatted before using the Card Reader. Otherwise, you may encounter problems
when using the Card Reader.
You can use only storage cards. Your Card Reader does not support cards with I/O
(input/output) functions such as a wireless network card or Bluetooth card.
Your computer has a Card Reader. The Card Reader is a small drive for
reading from and writing to removable storage cards (or called memory
cards). The Card Reader supports the MultiMediaCard (MMC), Secure
Digital (SD), Memory Stick (MS) and Memory Stick PRO (MS PRO)
cards.
Shown next are the appearance and size of each card type for your
reference.
Type
MMC Card
SD Card
MS/MS PRO Card
24×32×1.4
(mm)
24×32×2.1
(mm)
21.5×50×2.8
(mm)
Appearance
Size
4-6
Expanding Your Computer
To insert a storage card:
1.
Locate the Card Reader slot on the front of the computer and remove
the slot cover.
2.
Align the card with its connector pointing to the slot and its label
facing up. Slide the card into the slot until it reaches the end.
3. Windows will detect the card and assign it a drive name (typically E).
To remove a storage card:
1. Click Start, then Computer.
2. Right-click the drive with the card and select Safely Remove.
3. Pull the card out of the slot.
Expanding Your Computer
4-7
Using the Port Replicator (Optional)
A port replicator is available as an option. This device eliminates the
hassles of having you connect and disconnect the various cables when
carrying your computer around and allows a variety of peripherals to be
connected including a headphone or microphone, etc.
The following table shows the external components of the port replicator
and briefly describes the function of each component.
NOTE: Depending on the model you purchased, the appearance of your port replicator
may not be exactly the same as those shown in this manual.
Front Components
Ref
4-8
Component
Description
Expansion Bus
Connector
Connects to the computer via a port replicator cable.
USB Port
Connects a USB device, such as a flash disk, printer,
digital camera, joystick, and more.
Headphone
Connector
Connects a set of headphones, external speakers with
amplifier, or an audio recording device.
Microphone-in
Connector
Connects an external microphone.
Expanding Your Computer
Rear Components
Ref
Component
Description
USB Ports
Each of the two ports connects a USB device, such as a
flash disk, printer, digital camera, joystick, and more.
DVI-D Connector
Connects an external LCD monitor or digital CRT
monitor.
RJ-45 Connector
Connects the LAN cable.
Power Connector
Connects the AC adapter.
To start using the port replicator:
1.
Connect one end of the port replicator cable to the expansion bus
connector ( ) on the left side of your computer and the other end to
the port replicator ( ).
2.
Plug the DC cord of the AC adapter to the power connector on the
port replicator ( ).
Expanding Your Computer
4-9
3.
Plug the female end of the AC power cord to the AC adapter and the
male end to an electrical outlet ( ).
4. When the AC adapter is connected, power is being supplied from the
electrical outlet to the AC adapter and onto your port replicator. Now,
you are ready to connect various devices to your port replicator.
CAUTION:
When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the port replicator. A reverse procedure may damage the AC adapter or
the port replicator.
When unplugging the connector, always hold the plug head. Never pull on the cord.
4-10
Expanding Your Computer
The following table shows the behavior of the computer’s I/O (input/
output) ports when connecting various devices to the I/O ports on the port
replicator.
Component
USB Ports
Behavior of computer’s I/O ports
All three ports on the computer and all three ports on the port
replicator can be used at the same time.
Power Connector The AC adapter on the computer supplies power to the computer
while the AC adapter on the port replicator supplies power to the
port replicator.
RJ-45 Connector The system will automatically detect whether the LAN cable
was first connected to the computer or port replicator and will
use it.
DVI-D
Connector
Display output to the computer’s VGA port will be disabled.
Audio Output
Connector
The computer’s audio output connector will be disabled.
Microphone
Connector
The computer’s microphone connector will be disabled.
NOTE: The computer’s S/PDIF connector will also be disabled when the port replicator
is connected.
Expanding Your Computer
4-11
System Memory Upgrade
You can upgrade your computer by changing system memory to a
maximum of 3 GB on the 800 MHz DDR2 SO-DIMM slot.
CAUTION: RAM modules are extremely sensitive to static electricity. There are cases
where static electricity generated by the human body has adversely affected such
modules. When inserting or removing a RAM module, do not touch the terminals or
internal components, insert objects other than the module, or allow foreign particles to
enter. Doing so has been known to cause damage, fire, or electrical shock.
To install the RAM module:
1.
Remove the battery pack (see chapter 3) and make sure that the
computer is not connected to AC power.
2. Carefully place the notebook computer upside down.
3. Remove the two screws to open the compartment cover.
4-12
Expanding Your Computer
4. To install the RAM module, match the module's notched part with the
socket's projected part and firmly insert the module into the socket at
a 20-degree angle ( ). Then push down until the retaining clips lock
the module into position ( ).
CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force
it. Check once more to ensure that the module is positioned correctly.
5. Close the compartment cover and secure with two screws.
Expanding Your Computer
4-13
Chapter 5
CHAPTER
Using BIOS Setup
BIOS Setup Utility is a program for configuring the BIOS (Basic Input/
Output System) settings of the computer.
BIOS is a layer of software, called firmware, that translates instructions
from other layers of software into instructions that the computer hardware
can understand. The BIOS settings are needed by your computer to
identify the types of installed devices and establish special features.
This chapter tells you how to use the BIOS Setup program.
Using BIOS Setup
5-1
When and How to Use BIOS Setup
When to Use
You need to run BIOS Setup Utility when:
You see an error message on the screen requesting you to run BIOS
Setup Utility.
You want to restore the factory default settings.
You want to modify some specific settings according to the hardware.
You want to modify some specific settings to optimize the system
performance.
Starting BIOS Setup
NOTE:
The BIOS Setup Utility screens shown in this chapter are for your reference only.
The actual items or settings on your computer may differ.
The BIOS Setup Utility program may have been updated after the publication of this
manual.
The settings you select in your operating system might override similar settings in
BIOS Setup Utility.
To run BIOS Setup Utility, press the F2 key when the prompt appears on
the screen during system startup. The prompt shows up on the screen for
only a few seconds. You must press the F2 key quickly. The BIOS Setup
Utility main screen appears as shown next.
5-2
Using BIOS Setup
The BIOS Setup Utility screen can be divided into three areas:
On the top is the menu bar containing the titles of the available
menus. Each menu title brings a specific menu.
The left column of the menu displays the menu items.
The top-right of the menu provides more detailed information when a
menu item is highlighted.
The bottom of the menu provides keyboard instructions for moving
around and making selections.
Using BIOS Setup
5-3
Moving Around and Making Selections
You must go through two or three levels to complete the setting for an
item. In most cases, there are three levels: menu title, pull-down menu,
and submenu.
Use the keyboard to move around and make selections. Keyboard
information can be found at the bottom of the screen. A brief description
of keyboard usage is listed next:
Key
5-4
Function
←,→
Selects a menu title.
↑,↓
Selects an item or option.
Enter
1) Brings up the sub-menu when available.
2) Opens or closes the option window when an item is selected.
Esc
1) Exits BIOS Setup Utility.
2) Closes the option window if one is open.
F9
Loads setup defaults.
F10
Saves and exit the BIOS Setup Utility.
Using BIOS Setup
Main Menu
The Main menu contains the system date and time settings as well as
shows the basic configuration of the system.
System Time sets the system time.
System Date sets the system date.
Using BIOS Setup
5-5
Advanced Menu
The Advanced menu contains various system settings.
Legacy USB Support allows you to enable support for Legacy USB
device in DOS mode.
Boot-time Diagnostic Screen allows you to display the diagnostic
screen during system boot.
5-6
Using BIOS Setup
Security Menu
The Security menu contains the security settings, which safeguard your
system against unauthorized use.
Supervisor/User Password Is shows whether you have set the
supervisor/user password or not for the system.
Set Supervisor/User Password sets the supervisor/user password.
When typing the password, first make sure that Num Lock is off, and then
type the password in the entry fields and press Enter. Confirm your
password by typing it again and pressing Enter. You can set the
supervisor/user password to be required for starting up the system and/or
entering SCU.
NOTE:
You can set the user password only when the supervisor password has been set.
If both the administrator and user passwords are set, you can enter any of them for
starting up the system and/or entering SCU. However, the user password only
allows you to view/change the settings of certain items.
Password on Boot allows you to enable or disable the entering of
password for booting up your system. Once the password is successfully
set and this item is enabled, it is required for booting up the system.
Using BIOS Setup
5-7
TPM Support allows you to enable or disable TPM support. TPM is a
component on your computer’s mainboard that is specifically designed to
enhance platform security above-and-beyond the capabilities of today’s
software by providing a protected space for key operations and other
security critical tasks. Using both hardware and software, TPM protects
encryption and signature keys at their most vulnerable stages – operations
when the keys are being used unencrypted in plain-text form. TPM is
specifically designed to shield unencrypted keys and platform
authentication information from software-based attacks.
NOTE: Make sure to install the TPM driver before you can use the TPM feature (see
chapter 6 for details).
Current TPM State shows the current TPM state.
Change TPM State allows you to select between No Change, Clear,
Deactivate & Disable, and Enable & Activate.
5-8
Using BIOS Setup
Boot Menu
The Boot menu sets the sequence of the devices to be searched for the
operating system.
The bootable devices will be automatically detected during POST and
shown here, allowing you to set the sequence that the BIOS use to look
for a boot device from which to load the operating system.
A brief description of keyboard usage is listed next:
Key
Function
↑,↓
Selects (highlight) a boot device.
+, –
Changes the boot sequence.
1 to 4
Loads the four default boot sequence.
Shift + 1
Enables or disables a device.
Moves the highlighted boot device from the “Boot priority order”
list to the “Excluded from boot order” list, and vice versa.
Using BIOS Setup
5-9
Exit Menu
The Exit menu displays ways of exiting BIOS Setup Utility. After
finishing with your settings, you must save and exit so that the changes
can take effect.
Exit Saving Changes saves the changes you have made and exits BIOS
Setup Utility.
Exit Discarding Changes exits BIOS Setup Utility without saving the
changes you have made.
Load Setup Defaults loads the factory default values for all the items.
Discard Changes restores the previous values for all the items.
Save Changes saves the changes you have made.
5-10
Using BIOS Setup
Chapter 6
CHAPTER
Installing Software Drivers
and Using the P1 Utility
To take full advantage of the unique features of your computer, some
operating systems require custom software, known as drivers, to be
installed.
If you purchased the computer with Windows pre-installed, your dealer
may have already installed the drivers. If not, you need to install the
drivers using the disc supplied with your computer.
Also, located on top of your keyboard is the P1 quick button. The quick
button utility allows you to re-define (customize) the P1 quick button
according to your needs.
This chapter describes how to install the drivers as well as use the P1
quick button utility.
Installing Software Drivers
6-1
How to Use the Driver Disc
NOTE:
The drivers may have been updated after this manual was published. For driver
upgrade, please contact your dealer.
This disc supports Windows Vista only.
The available items may differ according to your computer model.
Do not remove the driver disc when installing the driver.
An autorun program is provided on the driver disc to help you easily
install the drivers. As you insert the disc, the autorun program
automatically starts. If you need to start the program manually, run the
Setup.exe program from the Wsetup directory of the disc.
The main screen appears as shown next:
6-2
Installing Software Drivers
Click NEXT located on the right lower part of main screen to view the next
screen as shown next.
Click BACK to return to the main screen.
Installing Software Drivers
6-3
Installing Drivers
To install the intended driver, click on the particular item and installation
will start. The drivers are described next:
Name
Description
Chipset
Ensures the full function of the following drivers. Install this
driver before installing the other device drivers.
VGA
Installs the video driver that allows you to select
high-resolution displays with richer colors.
Audio
Installs the audio driver that allows you to take full advantage
of the audio subsystem.
Card Reader
Installs the driver that allows the Card Reader to access
MultiMediaCard (MMC), Secure Digital (SD), Memory Stick
(MS) or Memory Stick PRO (MS PRO) card for removable
storage media.
LAN
Installs the LAN driver that allows you to use the network
function of the computer.
System Utility Installs the system utility driver that allows you to use the hot
keys with OSD (on-screen display) on the computer.
Touchpad
Installs the touchpad driver that allows you to take full
advantage of the touchpad features.
Bluetooth
(option)
Installs the Bluetooth driver and application program that
allows you to use the Bluetooth feature.
WLAN
(option)
Installs the WLAN driver and application program that allows
you to use the computer’s internal mini PCI-E WLAN card’s
network function.
NOTE: The Windows Plug-and-Play capability may automatically
detect the new device (mini PCI-E WLAN card) and display the wizard
requesting for drivers. Click Cancel to bypass the wizard screen(s).
Installs the driver that allows you to use the fingerprint module
security verification system.
Installs the TPM driver, a hardware-based security feature that
allows you to create and manage computer-generated digital
certificates.
Fingerprint
TPM
6-4
Installing Software Drivers
Name
Description
Turbo
Memory
(option)
Installs the Turbo Memory driver that allows you to use the
computer’s internal mini PCI-E Robson ES2 card for boosting
system performance.
NOTE: This icon would not appear if the mini PCI-E Robson ES2 card
is not installed.
CCD (option)
Installs the web camera driver that allows you to use the
computer’s built-in camera function.
Acrobat
Installs the Adobe Acrobat Reader program if you do not have
it on your computer. You need Adobe Acrobat Reader to open
the manual file supplied on this driver disc.
User’s Manual Allows you to view the User’s Manual.
Exit
Allows you to exit driver installation
(located on the right upper portion).
Installing Software Drivers
6-5
P1 Quick Button Utility
NOTE: Make sure to install the Quick Key driver to take advantage of the P1 quick
launch key utility.
The quick launch key utility allows you to define the “P1” quick launch
key.
icon and select the item Quick
To start the utility, right-click the
Button Definition. The following window appears as shown next.
Box
Open
6-6
Installing Software Drivers
Defining the buttons:
The box in the window represents the user-definable button.
To assign a program to a button, click the “Open” icon beside the box to
pop up the Open dialog box as shown next and select the desired program.
Then, click Open to complete the process.
The appropriate icon will then appear in the box. To launch the program,
press the P1 quick launch key, or, if the Quick Button Definition window is
open, click the box containing the icon.
Installing Software Drivers
6-7
Chapter 7
CHAPTER
Caring for the Computer
Taking good care of your computer will ensure a trouble-free operation
and reduce the risk of damage to your computer.
This chapter gives you guidelines covering these areas of maintenance:
How to protect the computer
What to note when using and storing the computer
How to clean the computer
What to note when using the battery pack
What to note when traveling with the computer
Caring for the Computer
7-1
Protecting the Computer
To safeguard the integrity of your computer data as well as the computer
itself, you can protect the computer in several ways as described in this
section.
Using the Windows Security Center
Windows Security Center protects your computer against intrusion.
7-2
Caring for the Computer
Windows Security Center alerts you to take action on the following
security essentials:
Windows Firewall
Windows Update
Malware Protection (anti-virus, anti-spyware)
Others (Internet security, user account control)
For detailed information on Windows Security Center, see Windows’
Help.
Using the Cable Lock
You can use a Kensington-type cable lock to protect your computer
against theft. The cable lock is available in most computer stores.
To use the lock, loop the lock cable around a stationary object such as a
table. Insert the lock to the Kensington lock hole and turn the key to
secure the lock. Store the key in a safe place.
Caring for the Computer
7-3
Taking Care of the Computer
Location Guidelines
Use the computer where the temperature is between 10 °C (50 °F) and
35 °C (95 °F).
Avoid placing the computer in a location subject to high humidity,
extreme temperatures, mechanical vibration, direct sunlight, or heavy
dust.
Do not cover or block any ventilation openings on the computer. For
example, do not place the computer on a bed, sofa, rug, or other
similar surface. Otherwise, overheating may occur that results in
damage to the computer.
Keep the computer at least 13 cm (5 inches) away from electrical
appliances that can generate a strong magnetic field such as a TV,
refrigerator, motor, or a large audio speaker.
Do not move the computer abruptly from a cold to a warm place. A
temperature difference of more than 10 °C (18 °F) will cause
condensation inside the unit, which may damage the storage media.
Do not place the computer on an unsteady surface.
General Guidelines
Wear protective gloves to prevent injury to your fingers when using
the computer in higher than normal temperature.
Do not place heavy objects on top of the computer when it is closed as
this may damage the display.
The screen surface is easily scratched. Do not use paper towels to
clean the display. Avoid touching it with your fingers, pen, or pencil.
To maximize the life of the backlight in the display, allow the
backlight to automatically turn off as a result of power management.
7-4
Caring for the Computer
Avoid using a screen saver or other software that prevents the power
management from working.
Cleaning Guidelines
Never clean the computer with its power on.
Use a soft cloth moistened with water or a non-alkaline detergent to
wipe the exterior of the computer.
Gently wipe the display with a soft, lint-free cloth. Do not use alcohol
or detergent on the display.
Dust or grease on the touchpad can affect its sensitivity. Clean the pad
by using adhesive tape to remove the dust and grease on its surface.
Battery Pack Guidelines
Recharge the battery pack when it is nearly discharged. When
recharging, make sure that the battery pack is fully charged. Doing so
may avoid harm to the battery pack.
Operate the computer with the battery pack installed even when using
external power. This ensures that the battery is fully charged.
If you will not be using the computer for a long period of time (more
than two weeks), remove the battery pack from the computer.
If you remove the battery pack, make sure that the battery terminals
do not contact any conductors such as metal objects or water.
Otherwise, the battery may become unusable as a result of a short
circuit.
If you need to store the battery pack, store it in a cool, dry place.
Never allow the temperature to exceed 60 °C (140 °F).
Do not leave the battery pack in storage for more than 6 months
without recharging it.
Caring for the Computer
7-5
When Traveling
Before traveling with your computer, make a backup of your hard
disk data into flash disks or other storage devices. As an added
precaution, bring along an extra copy of your important data.
Make sure that the battery pack is fully charged.
Make sure that the computer is turned off and the top cover is
securely closed.
Do not leave objects in between the keyboard and closed display.
Disconnect the AC adapter from the computer and take it with you.
Use the AC adapter as the power source and as a battery-charger.
Hand-carry the computer. Do not check it in as luggage.
If you need to leave the computer in the car, put it in the trunk of the
car to avoid exposing the computer to excessive heat.
When going through airport security, it is recommended that you
send the computer and flash disks through the X-ray machine (the
device you set your bags on). Avoid the magnetic detector (the device
you walk through) or the magnetic wand (the handheld device used
by security personnel).
If you plan to travel abroad with your computer, consult your dealer
for the appropriate AC power cord for use in your country of
destination.
7-6
Caring for the Computer
Chapter 8
CHAPTER
Troubleshooting
Computer problems can be caused by hardware, software, or both. When
you encounter any problem, it might be a typical problem that can easily
be solved.
This chapter tells you what actions to take when solving common
computer problems. It is divided into three sections:
Preliminary checklist
Solving common problems
Resetting the computer
Troubleshooting
8-1
Preliminary Checklist
Here are helpful hints to follow before you take further actions when you
encounter any problem:
Try to isolate which part of the computer is causing the problem.
Make sure that you turn on all peripheral devices before turning on
the computer.
If an external device has a problem, make sure that the cable
connections are correct and secure.
Make sure that the configuration information is properly set in the
BIOS Setup program.
Make sure that all the device drivers are correctly installed.
Make notes of your observations. Are there any messages on the
screen? Do any indicators light? Do you hear any beeps? Detailed
descriptions are useful to the service personnel when you need to
consult one for assistance.
If any problem persists after you follow the instructions in this chapter,
contact an authorized dealer for help.
8-2
Troubleshooting
Solving Common Problems
For easy reference, the problems are divided into these categories.
Problem Type
Go to
Battery Problems
P. 8-4
Bluetooth Wireless Problems
P. 8-4
DVD Drive Problems
P. 8-4
Display Problems
P. 8-5
ExpressCard Problems
P. 8-6
Hardware Device Problems
P. 8-6
Hard Disk Drive Problems
P. 8-7
Keyboard, Mouse, and Touchpad Problems
P. 8-8
LAN Problems
P. 8-8
WLAN Problems
P. 8-9
Power Management Problems
P. 8-10
Software Problems
P. 8-11
Sound Problems
P. 8-11
Startup Problems
P. 8-12
Other Problems
P. 8-13
Troubleshooting
8-3
Battery Problems
The battery does not charge (Battery Charge indicator does not light
amber).
Make sure that the AC adapter is properly connected.
Make sure that the battery is not too hot or cold. Allow time for the
battery pack to return to room temperature.
Make sure that the battery pack is installed correctly.
Make sure that the battery terminals are clean.
The operating time of a fully charged battery becomes shorter.
If you often partially recharge and discharge, the battery might not be
charged to its full potential. Initialize the battery to solve the problem.
(See “Initializing the Battery Pack” in Chapter 3 for instructions.)
The battery operating time indicated by the battery meter does not
match the actual operating time.
The actual operating time can be different from the estimated time,
depending on how you are using the computer. If the actual operating
time is much less than the estimated time, initialize the battery. (See
“Initializing the Battery Pack” in Chapter 3 for instructions.)
Bluetooth Wireless Problems
I cannot connect to another Bluetooth-enabled device.
Make sure that the Bluetooth card is correctly installed.
Make sure that the Bluetooth driver is correctly installed.
Make sure that both devices have activated Bluetooth.
Make sure that the distance between the two devices are not over
10 meters or that there are no walls or other obstructions between the
devices.
Make sure that the other device is not in “Hidden” mode.
8-4
Troubleshooting
Make sure that both devices are compatible.
DVD Drive Problems
The DVD drive cannot read a disc.
Make sure that the disc is correctly seated in the tray, with the label
facing up.
Make sure that the disc is not dirty. Clean the disc with a disc
cleaning kit, available in most computer stores.
Make sure that the DVD drive driver is installed correctly.
Make sure that the computer supports the disc or the files contained.
You cannot eject a disc.
The disc is not properly seated in the drive. Manually release the disc
following the method described next:
1. Insert a small rod, such as a straightened paperclip, into the
drive’s manual eject hole and push firmly to release the tray.
2. Pull the tray out until fully extended, and then remove the disc.
Display Problems
Nothing appears on the screen.
Make sure that the VGA driver is installed properly.
During operation, the screen may automatically turn off as a result of
power management. Press any key to see if the screen comes back.
Troubleshooting
8-5
The brightness level might be too low. Increase brightness by
pressing the Fn+F7 hot key.
The display output might be set to an external device. To switch the
display back to the LCD, press the Fn+F5 hot key or change the
display through the Display Settings Properties of Windows.
The characters on the screen are dim.
Adjust the brightness and/or contrast.
Bad dots appear on the display at all times.
A small number of missing, discolored, or bright dots on the screen
are an intrinsic characteristic of TFT LCD technology. It is not
regarded as a LCD defect.
The external monitor displays nothing.
Make sure that the monitor is turned on.
Make sure that the monitor’s signal cable is properly connected.
Switch the display to the monitor by pressing the Fn+F5 hot key or
change the display through the Display Settings Properties of
Windows.
Simultaneous display/multi-display does not work.
Make sure that you turn on the external monitor before turning on the
computer.
Press the Fn+F5 hot key to toggle through the display options or
through the Display Settings Properties of Windows.
ExpressCard Problems
The ExpressCard does not work.
Make sure that the ExpressCard is correctly seated.
If the card requires an IRQ (Interrupt ReQuest), make sure that there
is one available.
8-6
Troubleshooting
The ExpressCard stops communicating properly.
The application may have been reset when the computer is turned off
or in Sleep mode. Exit and restart the application.
Hardware Device Problems
The computer does not recognize a newly installed device.
The device may not be correctly configured in the BIOS Setup
program. Run the BIOS Setup program to identify the new type.
Make sure if any device driver needs to be installed. (Refer to the
documentation that came with the device.)
Make sure if the device needs any jumper or switch settings. (Refer to
the documentation that came with the device.)
Check the cables or power cords for correct connections.
For an external device that has its own power switch, make sure that
the power is turned on.
Hard Disk Drive Problems
The hard disk drive error message appears on the screen.
The hard disk drive has defects. Ask your dealer for help.
The hard disk drive operations seem slow.
The data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
The hard disk drive in-use indicator glows without blinking.
The data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
Troubleshooting
8-7
Keyboard, Mouse, and Touchpad Problems
The keyboard does not respond.
Try connecting an external keyboard. If it works, contact an
authorized dealer, as the internal keyboard cable might be loose.
The numeric keypad is disabled.
Make sure that the Num Lock is switched on. (Check if the Num Lock
Indicator glows or not.)
The external keyboard does not work.
Make sure that the keyboard cable is properly connected.
The USB mouse does not work.
Make sure that the mouse cable is properly connected.
The touchpad does not work, or the pointer is difficult to control
with the touchpad.
Make sure that the touchpad driver is correctly installed.
Make sure that the touchpad is clean.
LAN Problems
I cannot access the network.
Make sure that the LAN driver is correctly installed.
Make sure that the LAN cable is properly connected to the RJ-45
connector and the network hub.
Make sure that the network configuration is appropriate.
Make sure that the user name or password is correct.
8-8
Troubleshooting
WLAN Problems
I cannot use the WLAN feature.
Make sure that the mini PCI-E WLAN card is correctly installed.
Make sure that the necessary driver(s) is correctly installed.
Make sure that the WLAN feature is turned on.
Transmission quality is poor.
Your computer may be in an out-of-range situation. Move your
computer closer to the Access Point or another WLAN device it is
associated with.
Check if there is high interference around the environment and solve
the problem as described next.
Radio interference exists.
Move your computer away from the device causing the radio
interference such as microwave oven and large metal objects.
Plug your computer into an outlet on a different branch circuit from
that used by the affecting device.
Consult your dealer or an experienced radio technician for help.
I cannot connect to another WLAN device.
Make sure that the WLAN feature is turned on.
Make sure that the SSID setting is the same for every WLAN device
in the network.
Your computer is not recognizing changes. Restart the computer.
Make sure that the IP address or subnet mask setting is correct.
I cannot communicate with the computer in the network when
Infrastructure mode is configured.
Make sure that the Access Point your computer is associated with is
powered on and all the LEDs are working properly.
Troubleshooting
8-9
If the operating radio channel is in poor quality, change the Access
Point and all the wireless station(s) within the BSSID to another radio
channel.
Your computer may be in an out-of-range situation. Move your
computer closer to the Access Point it is associated with.
Make sure that your computer is configured with the same security
option (encryption) to the Access Point.
Use the Web Manager/Telnet of the Access Point to check whether it
is connected to the network.
Reconfigure and reset the Access Point.
I cannot access the network.
Make sure that the necessary driver(s) is correctly installed.
Make sure that the network configuration is appropriate.
Make sure that the user name or password is correct.
You have moved out of range of the network.
Turn off power management.
Power Management Problems
The computer does not enter Sleep or Hibernation mode
automatically.
If you have a connection to another computer, the computer does not
enter Sleep or Hibernation mode if the connection is actively in use.
Make sure that the Sleep or Hibernation time-out is enabled.
The computer does not enter Sleep or Hibernation mode
immediately.
If the computer is performing an operation, it normally waits for the
operation to finish.
8-10
Troubleshooting
The computer does not resume from Sleep or Hibernation mode.
The computer automatically enters Sleep or Hibernation mode when
the battery pack is empty. Do any one of the following:
− Connect the AC adapter to the computer.
− Replace the empty battery pack with a fully charged one.
The computer does not enter Hibernation mode with the Fn+F12 hot
keys.
Make sure that the Hibernation function is specified for the sleep
button.
You might be using an ExpressCard that prevents the computer from
entering Hibernation mode. To enter the mode, stop the
communication program and then remove the card or stop the card.
Software Problems
An application program does not work correctly.
Make sure that the software is correctly installed.
If an error message appears on the screen, consult the software
program’s documentation for further information.
If you are sure the operation has stop, reset the computer. (See
“Resetting the Computer” later in this chapter.)
Sound Problems
No sound is produced.
Make sure that the volume control is not set too low.
Make sure that the audio driver is correctly installed.
Make sure that the computer is not in Sleep mode.
If using an external speaker, make sure that the speaker is properly
connected.
Troubleshooting
8-11
Distorted sound is produced.
Make sure that the volume control is not set too high or too low. In
most cases, a high setting can cause the audio electronics to distort the
sound.
The sound system does not record.
Adjust the playback or recording sound levels.
The external microphone or audio device does not work.
Make sure that the microphone is connected to the proper connector
on the computer.
Make sure that your computer is equipped with the driver needed.
Click the speaker symbol on the taskbar and check the Windows
volume control.
Check the volume control of your computer.
Startup Problems
When you turn on the computer, it does not respond.
If you are using an external AC power, make sure that the AC adapter
is correctly and securely connected. If so, make sure that the electrical
outlet works properly.
If you are using the battery power, make sure that the battery is not
discharged.
When you turn on the computer, it stops after POST.
Restart your computer.
The message “Operating system not found” appears on the
screen after you turn on the computer.
If this message appears when you are booting from the hard disk,
insert a bootable disc in the DVD drive and check the condition of the
hard disk.
8-12
Troubleshooting
The message “Invalid system disk” or “Disk error” appears
on the screen after you turn on the computer.
If you are deliberately trying to boot from a disc, replace the disc with
a bootable one and press any key to continue booting.
If this message appears when you are booting from the hard disk,
insert a bootable disc in the DVD drive and check the condition of the
hard disk.
Other Problems
The date/time is incorrect.
Correct the date and time via the operating system or BIOS Setup
program.
After you have performed everything as described above and still
have the incorrect date and time every time you turn on the computer,
the RTC (Real-Time Clock) battery is at the end of its life. Call an
authorized dealer to replace the RTC battery.
Troubleshooting
8-13
Resetting the Computer
You may have to reset (reboot) your computer on some occasions when
an error occurs and the program you are using hangs up.
If the computer operation seems to hang up, first wait. It is possible that
the computer is processing data. Periodically check the hard disk drive
in-use indicator, if it flashes irregularly, the program may be accessing
data and preventing you from using the keyboard. If you are sure the
operation has stopped and you cannot use the “restart” function of the
operating system, reset the computer.
Reset the computer by any one of these methods:
Press Ctrl+Alt+Del.
If the above action does not work, turn off the computer. Wait for at
least five seconds and turn it on again.
CAUTION: Resetting will cause any unsaved data to be lost.
8-14
Troubleshooting
Appendix A
APPENDIX
Specifications
NOTE: Specifications are subject to change without any prior notice.
Parts
Durability
100 c.c. water on system cover
Drop
45 cm height (operating and non-operating)
Stress
120 kg on surface, 15 kg / 13 points on LCD housing
NorthBridge
Intel® Mobile Penryn (ultra-low voltage) Montevina (small form
factor) processor, 800 MHz FSB (Front Side Bus), Thermal
specifications 10 W (maximum)
Intel® GS45
CPU
Chipset
SouthBridge
ROM BIOS
RAM
System
Display
Panel
Audio
Specifications
Spill-resistant
Intel® ICH9-E (small form factor)
2 MB EEPROM, Fingerprint and TPM security
Up to 3 GB, 200-pin, DDRII 800 MHz SO-DIMM, 1.25-inch height
13.3-inch TFT, resolution up to 1280×800 WXGA
Video controller
UMA
Video ports
Subsystem
VGA port
Azalia interface, 2.1-channel analog output
Ports
Three audio ports for Line-out / Mic-in / S/PDIF
Speakers
2 × 1.5 Watt stereo
Microphone
× 2 Mic array
Keyboard
Quick keys
Pointing device
Storage
Hard disk drive
device
Optical drive
Card slots
Specifications
Standard keys, numeric keypad, 12 function keys, a special Fn
(Function) key and Windows keys
ECO (power saving), Microsoft® Internet Explorer®, and
P1 (Program 1 – user customized) quick launch key
Glide touchpad without scroll bar and 2 buttons
SATA interface, 4200/5400 rpm support, 9.5 mm height,
2.5-inch diameter
DVD Super Multi, 9.5 mm height
ExpressCard/34, Card Reader (SD / MS / MS Pro / MMC)
A-1
Parts
Specifications
I/O ports
LAN
Wireless LAN
Three USB ports (USB 2.0 support), RJ-45 port, port replicator
10/100/1000 based-T
One mini PCI-E slot for wireless LAN card, compliant with
IEEE 802.11b/g/n
Bluetooth
Camera
Security
Specification 2.1 module
Webcam 1.3 M with Mic array
Fingerprint sensor slide-type, TPM 1.2, Kensington lock
Power
AC adapter
Battery
Dimension (W×D×H)
Weight
Environment
Temperature
Humidity
Regulation
EMC
Safety
Universal AC adapter 65 Watt; input: 100∼240 Volt, output: 19 Volt
3-cell Li-ion battery 2600 mAh / 14.8 V
6-cell Li-ion battery 5200 mAh / 11.1 V
321×228×20~29 mm (12.6×9×0.8~1.14 inch)
1.7 kg (3.75 lb)
Operating: 0 °C (32 °F) to 35 °C (95 °F)
Storage: –20 °C (–4 °F) to 60 °C (140 °F)
Operating: 10 % to 90 % non-condensing
Storage: 5 % to 95 % non-condensing
CE
Energy Star
CB
Energy Star 4.0
Green Product Coverage
RoHS-compliant
A-2
Specifications
Appendix B
APPENDIX
Regulatory Information
This appendix provides regulatory statements and safety notices on your
computer.
NOTE: Marking labels located on the exterior of your computer indicate the regulations
that your model complies with. Please check the marking labels and refer to the
corresponding statements in this appendix. Some notices apply to specific models only.
Regulatory Information
B-1
On the Use of the System
Class B Regulations
USA
Federal Communications Commission Radio Frequency
Interference Statement
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Please note:
The use of a non-shielded interface cable with this equipment is
prohibited.
B-2
Regulatory Information
Canada
Canadian Department of Communications
Radio Interference Regulations Class B Compliance Notice
This Class B digital apparatus meets all requirements of the Canada
Interference-Causing equipment regulations.
Cet appareil numérique de Classe B respecte toutes les exigences du
Règlement Canadien sur le matériel brouileur.
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.
Safety Notices
About the Battery
Caution Texts Concerning Lithium Batteries
DANISH
ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må
kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til
leverandøren.
NORWEGIAN
ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype
eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i
henhold til fabrikantens instruksjoner.
SWEDISH
VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt
fabrikantens instruktion.
FINNISH
VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
Regulatory Information
B-3
ENGLISH
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the equipment manufacturer. Discard used
batteries according to manufacturer's instructions.
DEUTSCH
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur
durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
FRENCH
ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d’un type équivalent
recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
Attention (for USA Users)
The product that you have purchased contains a rechargeable battery. The
battery is recyclable. At the end of its useful life, under various state and
local laws, it may be illegal to dispose of this battery into the municipal
waste stream. Check with your local solid waste officials for details in
your area for recycling options or proper disposal.
About the AC Adapter
Use only the AC adapter supplied with your computer. Use of another
type of AC adapter will result in malfunction and/or danger.
Do not use the adapter in a high moisture environment. Never touch
the adapter when your hands or feet are wet.
Allow adequate ventilation around the adapter when using it to
operate the device or charge the battery. Do not cover the AC adapter
with paper or other objects that will reduce cooling. Do not use the
AC adapter while it is inside a carrying case.
Connect the adapter to a proper power source. The voltage
requirements are found on the product case and/or packaging.
Do not use the adapter if the cord becomes damaged.
Do not attempt to service the unit. There are no serviceable parts
inside. Replace the unit if it is damaged or exposed to excess
moisture.
B-4
Regulatory Information
On the Use of the RF Device
NOTE: The information in this section applies to models with the wireless LAN module.
USA and Canada Safety Requirements and Notices
IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Radio Frequency Interference Requirements and SAR
The FCC with its action in ET Docket 93-62 has adopted a safety standard
for human exposure to Radio Frequency (RF) electromagnetic energy
emitted by FCC certified equipment. The wireless LAN module meets the
Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE
C95.1, 1992. Proper operation of this radio according to the instructions
found in this manual will result in exposure substantially below the
FCC’s recommended limits. The following safety precautions should be
observed:
Do not touch or move antenna while the unit is transmitting or
receiving.
Do not hold any component containing the radio such that the
antenna is very close or touching any exposed parts of the body,
especially the face or eyes, while transmitting.
Do not operate the radio or attempt to transmit data unless the antenna
is connected; if not, the radio may be damaged.
Use in specific environments:
The use of wireless devices in hazardous locations is limited by the
constraints posed by the safety directors of such environments.
The use of wireless devices on airplanes is governed by the Federal
Aviation Administration (FAA).
Regulatory Information
B-5
The use of wireless devices in hospitals is restricted to the limits set
forth by each hospital.
Antenna use:
In order to comply with FCC RF exposure limits, low gain integrated
antennas should be located at a minimum distance of 20 cm
(8 inches) or more from the body of all persons.
High-gain, wall-mount, or mast-mount antennas are designed to be
professionally installed and should be located at a minimum distance
of 30 cm (12 inches) or more from the body of all persons. Please
contact your professional installer, VAR, or antenna manufacturer for
proper installation requirements.
Explosive Device Proximity Warning
WARNING: Do not operate a portable transmitter (such as a wireless
network device) near unshielded blasting caps or in an explosive
environment unless the device has been modified to be qualified for such
use.
Antenna Warning
WARNING: To comply with the FCC and ANSI C95.1 RF exposure limits,
it is recommended that the antenna for this device be installed so as to
provide a separation distance of at least 20 cm (8 inches) from all persons
and that the antenna must not be co-located or operating in conjunction
with any other antenna or radio transmitter. It is recommended that the
user limit exposure time if the antenna is positioned closer than 20 cm
(8 inches).
Use on Aircraft Caution
CAUTION: Regulations of the FCC and FAA prohibit airborne operation
of radio-frequency wireless devices because their signals could interfere
with critical aircraft instruments.
B-6
Regulatory Information
EMC Requirements
This device uses, generates and radiates radio frequency energy. The
radio frequency energy produced by this device is well below the
maximum exposure allowed by the Federal Communications
Commission (FCC).
This device complies with the limits for a Class B digital device pursuant
to Part 15 subpart C of the FCC Rules and Regulations. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
The FCC limits are designed to provide reasonable protection against
harmful interference when the equipment is installed and used in
accordance with the instruction manual and operated in a commercial
environment. However, there is no guarantee that interference will not
occur in a particular commercial installation, or if operated in a residential
area.
If harmful interference with radio or television reception occurs when the
device is turned on, the user must correct the situation at the user’s own
expense. The user is encouraged to try one or more of the following
corrective measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: The Part 15 radio device operates on a non-interference basis
with other devices operating at this frequency. Any changes or
modification to said product not expressly approved by the manufacturer
could void the user’s authority to operate this device.
Regulatory Information
B-7
Canada Radio Frequency Interference Requirements
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and away from windows to provide
maximum shielding. Equipment (or its transmit antenna) that is installed
outdoors is subject to licensing.
Pour empêcher que cet appareil cause du brouillage au service faisant
l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé
loin des fenêtres afin de fournir un écran de blindage maximal. Si le
matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire
l'objet d'une licence.
European Union CE Marking and Compliance Notices
Statements of Compliance
English
This product follows the provisions of the European Directive
1999/5/EC.
Danish
Dette produkt er i overensstemmelse med det europæiske direktiv
1999/5/EC.
Dutch
Dit product is in navolging van de bepalingen van Europees Directief
1999/5/EC.
Finnish
Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä.
French
Ce produit est conforme aux exigences de la Directive Européenne
1999/5/EC.
German
Dieses Produkt entspricht den Bestimmungen der Europäischen
Richtlinie 1999/5/EC.
B-8
Regulatory Information
Greek
To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας
1999/5/EC.
Icelandic
Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
1999/5/EC.
Italian
Questo prodotto è conforme alla Direttiva Europea 1999/5/EC.
Norwegian
Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
1999/5/EC.
Portuguese
Este produto cumpre com as normas da Diretiva Européia 1999/5/EC.
Spanish
Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
Swedish
Denna produkt har tillverkats i enlighet med EG-direktiv 1999/5/EC.
Local Restrictions of 802.11b/g/n Radio Usage
802.11a wireless LAN devices: For operation within 5.15 ~ 5.25 GHz
frequency range, it is restricted to indoor usage environments, and the
antenna of this device must be integral.
CAUTION: Due to the fact that the frequencies used by 802.11b/g/n
wireless LAN devices may not yet be harmonized in all countries,
802.11b/g/n products are designed for use only in specific countries or
regions, and is not allowed to be operated in countries or regions other
than those of designated use. As a user of these products, you are
responsible for ensuring that the products are used only in the countries or
regions for which they were intended and for verifying that they are
configured with the correct selection of frequency and channel for the
country or region of use. Any deviation from permissible settings and
restrictions in the country or region of use could be an infringement of
local law and may be punished as such.
Regulatory Information
B-9
The European variant is intended for use throughout the European
Economic Area. However, authorization for use is further restricted in
particular countries or regions within countries, as follows:
General
European standards dictate maximum radiated transmit power of
100 mW Effective Isotropic Radiated Power (EIRP) and the frequency
range 2400 – 2483.5 MHz.
Belgium and the Netherlands
In Belgium and the Netherlands, the product may not be used outdoors.
See the instructions next under the heading “Turning Off the Wireless
LAN Radio.”
France
Departments in Which the Wireless LAN Module Can Be Used
(Indoors Only)
The wireless LAN module can currently be used indoors only in the
following 38 departments of mainland France. Please turn off your
wireless LAN radio when operating the device in areas/places other than
the 38 departments listed:
B-10
01
Ain Orientales
36
Indre
66
Pyrénées
02
Aisne
37
Indre et Loire
67
Bas Rhin
03
Allier
41
Loir et Cher
68
Haut Rhin
05
Hautes Alpes
42
Loire
70
Haute Saône
08
Ardennes
45
Loiret
71
Saône et Loire
09
Ariège
50
Manche
75
Paris
11
Aude
55
Meuse
82
Tarn et Garonne
12
Aveyron
58
Nièvre
84
Vaucluse
16
Charente
59
Nord
88
Vosges
24
Dordogne
60
Oise
89
Yonne
25
Doubs
61
Orne
90
Territoire de Belfort
26
Drôme
63
Puy du Dôme
94
Val de Marne
32
Gers
64
Pyrénées Atlantique
Regulatory Information
Departments in Which the Wireless LAN Module’s Maximum EIRP
Not Shown in the Previous Table
Frequency Ranges (MHz)
Indoors
Outdoors
2400 – 2446.5
10 mW
Not permitted
2446.5 – 2483.5
100 mW
100 mW on private property with
Ministry of Defense approval
Turning Off the Wireless LAN Radio
NOTE: Turning the wireless LAN radio off is not the same as disabling the
wireless LAN card. It is not necessary to disable the card to meet the
regulatory requirements.
While operating the computer in those French departments that do not
allow use of the wireless LAN equipment, the user of the equipment must
turn off the wireless LAN radio in order to comply with local regulations
(see Chapter 2 for more information).
Regulatory Information
B-11
Index
—A—
AC adapter, 3-2
Connecting, 1-2
Specifications, A-2
AC power
Connecting, 1-2
ACPI, 3-12
Adobe Acrobat Reader, 6-5
Alt key, 2-5
Antenna warning, B-7
Audio connector, 2-21
Audio driver, 6-4
Audio output connector, 1-10, 2-22
Audio subsystem
Connecting external audio device, 2-22
Driver installation, 6-4
Feature, 2-21
Specifications, A-1
Troubleshooting, 8-12
—B—
Battery charge
Indicator, 1-14, 3-3
Battery low, 3-11
Battery pack, 1-11
Battery low, 3-11
Charging, 3-3
Checking battery level, 3-5
Initializing, 3-4
Replacing, 3-6
Index
Safety notices, B-3
Secondary, 1-6, 3-8
Specifications, A-2
Taking care, 3-3, 7-6
Troubleshooting, 8-4
BIOS Setup, 5-1
Advanced menu, 5-6
Boot menu, 5-8
Exit menu, 5-9
Exiting, 5-9
Legacy USB, 5-6
Main menu, 5-5
Security menu, 5-7
Starting, 5-2
Bluetooth feature
Connecting to Bluetooth device, 2-37
Driver installation, 6-4
Indicator, 1-14
Turning off, 2-36
Turning on, 2-36
Using, 2-36
Boot sequence, 5-8
Booting, 2-2
Brightness
Hot keys, 2-8
—C—
Canada
Class B compliance notice, B-3
RF interference requirements, B-9
Caps Lock
Indicator, 1-13
I-1
Card Reader, 4-11, See Storage card
Driver installation, 6-4
Indicator, 1-14
Inserting a card, 4-12
Removing a card, 4-12
CD. See DVD drive
Charging, 3-3
Chipset driver, 6-4
Class 1 laser product, 2-16
Cleaning the computer, 7-6
Click, 2-11
Connecting external device
Monitor, 4-2
USB device, 4-4
Connector
Audio output, 1-10, 2-22
Microphone, 1-10, 2-22
RJ-45, 1-7
VGA, 1-8
Copyright protection
Macrovision Corp., 2-17
Cover
Opening, 1-4
CPU, A-1
Ctrl key, 2-5
Cursor, 2-6
Cursor-control key, 2-6
—D—
Date
BIOS Setup, 5-5
Troubleshooting, 8-14
DC, 3-2
Dimension of the computer, A-2
Display
Troubleshooting, 8-5
Display mode, 2-19
Display output
Hot keys, 2-8
Double-click, 2-11
Drag and drop, 2-11
Drive C, 2-13
Drive E, 4-12
Driver installation, 6-1
Driver OS support, 6-2
I-2
DVD drive, 1-6, 2-16
Inserting a disc, 2-17
Troubleshooting, 8-4
DVD Dual drive. See DVD drive
—E—
EEPROM, A-1
EMC requirements, B-8
Environmental specifications, A-2
Esc key, 2-5
EU
CE marking and compliance notices,
B-9
Euro symbol, 2-9
External monitor
Connecting, 4-2
—F—
FCC
Class B regulations, B-2
FDA regulations, 2-16
Fingerprint
Enrolling, 2-42
Fingerprint module
Driver installation, 6-5
Fingerprint sensor, 1-13
Using, 2-40
Fingerprint software
Change setting, 2-44
Fn key, 2-7
Function key, 2-7
—G—
Gas gauge
Battery pack, 3-6
Secondary battery pack, 3-10
Index
—H—
Hard disk drive
Indicator, 1-13
Secondary, 1-6, 2-13
Troubleshooting, 8-7
Hibernation, 2-3, 3-12, 3-13
Troubleshooting, 8-11
Hot keys, 2-7
Display output, 2-8
LCD, 2-8
LCD brightness, 2-8
Mute, 2-8
Power saving, 2-8
Touchpad, 2-8
Volume, 2-8
WLAN radio, 2-8
Humidity, A-2
—I—
Indicator
Battery charge, 1-14, 3-3
Bluetooth feature, 1-14
Caps Lock, 1-13
Card Reader, 1-14
Hard disk drive, 1-13
Num Lock, 1-13
Optical drive, 1-13
Power, 1-14
WLAN, 1-13
—K—
Kensington lock, 1-9, 7-4
Keyboard, 1-13
Troubleshooting, 8-7
Using, 2-5
—L—
LAN, 2-31
Connector, 1-7
Index
Driver installation, 6-4
Troubleshooting, 8-8
LCD, 1-12, 2-19
Switching on and off with hot keys, 2-8
Location of the computer, 7-5
Low battery. See Battery low
—M—
Memory card. See Storage card
Memory Stick. See Storage card
Memory Stick PRO. See Storage card
Microphone, 1-10, 2-21
Microphone connector, 1-10, 2-22
Mouse
Troubleshooting, 8-7
MultiMediaCard. See Storage card
Mute
Hot keys, 2-8
—N—
Network. See LAN
Num Lock
Indicator, 1-13
Numeric key, 2-6
—O—
Operating system, 1-5, 2-2
Optical drive
Indicator, 1-13
OSD utility
Driver installation, 6-5
—P—
P1 utility
Defining the button, 6-7
Using, 6-6
Point, 2-11
POST, 1-5
I-3
Power
Indicator, 1-14
Power button, 1-13, 2-2
Power connector, 1-9
Power Management, 3-12
Troubleshooting, 8-11
Power-On Self Test. See POST
—Q—
Quick button
ECO, 1-12, 2-4
P1, 1-12, 2-4
Using, 2-4
—R—
RAM, A-1
Rebooting, 8-15
Record volume
Adjusting, 2-23
Resetting
Computer, 8-15
Restarting
Computer, 8-15
RF device
Safety Requirements and Notices, B-6
RF switch, 1-8
RJ-45, 1-7, 2-31
ROM BIOS, A-1
—S—
Saving power, 3-14
Screen. See LCD
Scroll, 2-12
Secure Digital. See Storage card
Security
Protecting the computer with lock, 7-4
Protecting the computer with password,
7-3
Shutting down, 2-2
Computer, 1-5
Simultaneous display, 2-19
I-4
Sleep button
Hot keys, 2-8
Sleep mode, 2-2, 3-12
Troubleshooting, 8-11
Software
Troubleshooting, 8-12
Software driver, 6-1
Speaker, 1-11, 2-21
Connecting external speakers, 2-22
Specifications, A-1
Startup
Computer, 2-2
Troubleshooting, 8-13
Storage card, 4-11
Inserting, 4-12
Removing, 4-12
Super Multi drive. See DVD drive
Swappable bay, 1-6
—T—
Temperature, A-2
TFT, 2-19
Time
BIOS Setup, 5-5
Troubleshooting, 8-14
Touchpad, 1-13, 2-10
Configuring, 2-12
Driver installation, 6-4
Hot keys, 2-8
Troubleshooting, 8-7
TPM
BIOS Setup, 5-7
Driver installation, 6-5
Traveling with the computer, 7-7
Troubleshooting, 8-1
Battery problem, 8-4
Bluetooth problem, 8-4
Display problem, 8-5
DVD drive problem, 8-4
Hard disk drive problem, 8-7
Hardware problem, 8-6
Keyboard problem, 8-7
LAN problem, 8-8
Mouse problem, 8-7
Other problem, 8-14
Index
Power Management problem, 8-11
Software problem, 8-12
Sound problem, 8-12
Startup problem, 8-13
Touchpad problem, 8-7
WLAN problem, 8-8
Turning off, 2-2
Computer, 1-5
Turning on
Computer, 1-4
Typewriter key, 2-5
—U—
Upgrading the computer, 4-13
USB device
Connecting, 4-4
USB port, 1-7, 1-8, 4-4
—V—
VGA connector, 1-8, 4-2
Video driver, 6-4
Video subsystem
Configuring, 2-19
Index
Driver installation, 6-4
Feature, 2-19
Video controller, A-1
Volume control
Hot keys, 2-8
—W—
Weight of the computer, A-2
Windows key, 2-9
Windows Security Center, 7-2
Wireless network
Connecting, 2-33
WLAN card, 1-11
WLAN feature
Driver installation, 6-4
Troubleshooting, 8-8
Turning off, 2-33
Turning on, 2-33
Using, 2-32
WLAN radio
Indicator, 1-13
France restrictions, B-11
Hot keys, 2-8
Local restrictions, B-10
I-5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
Page Count                      : 141
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:680a551b-a83a-46d0-b0a0-38206062421b
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Create Date                     : 2008:10:13 16:10:39+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:10:13 16:15:58+08:00
Metadata Date                   : 2008:10:13 16:15:58+08:00
Document ID                     : uuid:8d2063e3-6162-4879-8a82-4eca4f35e1e8
Format                          : application/pdf
Creator                         : kety_h
Title                           : Microsoft Word - 9213 User's Manual-AW.DOC
Author                          : kety_h

EXIF Metadata provided by EXIF.tools