Giant Electronics L8270 Two Way Radio with FRS User Manual YOUR NEW RADIO
Giant Electronics Ltd Two Way Radio with FRS YOUR NEW RADIO
User Manual
1
Cover
LA8270 User Manual
2
SAFETY AND GENERAL INFORMATION
Important Information for Safe and Efficient Operation
Please read this information before using your radio.
Safety and General
1. Do not transmit more than 50% of time. It is important as the radio generates measurable RF
energy exposure only when transmitting.
2. Do not open the radio. Any unauthorized modification may invalidate the guarantee.
3. Radio frequency signals transmitted may cause interference to hearing aids.
4. Turn off the radio when near medical equipment.
5. This product should not be used by people with pacemakers.
6. Do not use the radio when driving a vehicle or operating machinery.
7. Do not use the radio when on board aircraft.
8. Do not hold the antenna when transmitting.
9. Do not use the radio when the antenna has damaged.
10. Turn off the radio and remove the batteries if you are not going to use it for a long time.
11. Do not attempt to charge alkaline batteries.
3
Transmit and Receive Procedures
Your wireless hand-held portable transceiver contains a low power transmitter. When the
Push-to-Talk (PTT) button is pushed it sends out radio frequency (RF) signals. The device is
authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal
Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for
hand-held wireless devices.
RF Exposure
CAUTION: To maintain compliance with the FCC's RF exposure guidelines hold the transmitter
and antenna at least 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the
antenna pointed up and away from the face. If you wear the handset on your body while using the
headset accessory, use only the supplied belt clip for this product and when transmitting, take it out
of the belt to ensure that the antenna is at least 1 inch (2.5 centimeters) from your body. Use only
the supplied antenna.
Unauthorized antennas, modifications, or attachments could damage the transmitter and may
violate FCC regulations.
OPERATIONAL CAUTIONS
4
1. Never dispose of batteries in a fire. There is a serious risk of explosion and /or the release of
highly toxic chemicals.
2. Do not expose your product to direct sunlight, extreme cold or place it near heating
appliances.
3. Do not submerge any part of your product in water and do not use it in damp, humid or wet
conditions.
4. Do not expose your product to fire, explosive or other hazardous conditions. For example, at
petrol stations or areas where explosive products are used.
5. Turn off the radio when during charging.
USING YOUR RADIO
Read this manual carefully before use.
Your radio has 14 channels. All radios in your group must be set to the same channel and
Interference Eliminator Code in order to communicate with each other.
• For maximum clarity, hold radios 5 to 7 centimeters from mouth.
and speak into the microphone.
• Press and hold
• To receive messages, release .
1. Antenna
2.
• Power on/off.
• Increase/Decrease volume.
3.
• Push to transmit, release to listen.
• Pressing has 60 seconds limit.
• In menu mode, push to confirm selection.
4. mon/
• Push to monitor/scan channels.
5
5.
• Push to decreases the channel / CTCSS Code / select VOX level and call tone.
6. CALL
• Short press to send a single call tone.
• Long press to send the call tone maximum 10 times, and
then returns to standby mode automatically.
7. LCD
8. mode/
• Short press enters menu mode
-- Press one time to enter MENU mode, press or to select RF channel.
-- Press two times to enter CTCSS mode, press or to set CTCSS code.
-- Press three times to enter Call Tone mode, press or to set a new call tone.
or to set sensitivity level.
-- Press four times to enter Sensitivity Level mode, press
-- Press five times to enter Stop Watch mode. Press to start/pause the stop watch, press
to reset.
-- Press six times to exit MENU mode.
• Long press to lock/unlock keypad.
It will be automatically exited the menu mode if you have not pressed any key for several
seconds when you in any mode.
9.
• Push to increases the channel / CTCSS Code / select VOX level and call tone.
6
: displays the battery level
: displays the channel number
: displays the CTCSS Code
: Scanning
: displays when VOX function turn on
: keypad locked
: talk confirmation tone
Turning Your Radio On And Off
Turn clockwise to turn your radio on. The radio chirps and the display will show all feature
icons that your radio has available for a brief period. The display will show the channel 1 - 14 and
interference eliminator code 0 - 38. Turn counterclockwise to turn your radio off.
Volume
Rotate while holding down mon/ key until you reach a comfortable listening level.
Rotate clockwise to increase the volume or counterclockwise to decrease the volume.
7
Select Channel
1. Press mode/ button. The channel number will begin to flash.
2. Use or button to change channel.
3. Press button to set the new channel.
CH FREQ
(MHz) CH FREQ
(MHz)
1 462.5625 8 467.5625
2 462.5875 9 467.5875
3 462.6125 10 467.6125
4 462.6375 11 467.6375
5 462.6625 12 467.6625
6 462.6875 13 467.6875
7 462.7125 14 467.7125
Scan
Use scanning to monitor channels and codes for transmissions or to find someone in your group
who has accidentally changed channels.
To start scanning, briefly press and release mon/ key. The scan indicator is shown.
8
When the radio detects channel activity, it stops scanning and you can hear the transmission. To
respond to the transmission, press .
Note: If your radio’s Interference Eliminator Code is set to 0 while scanning, the radio checks for
activity on each channel regardless of the code used on the channel. If your radio’s Interference
Eliminator Code is set to 1-38 and ignores channels using code 0.
Scan Advance
If scan stops on a channel that you don’t want to listen, briefly press or button to resume
scanning for the next active channel.
Monitor
There are multiple channels shared among all users on the “take turn” basis. For uninterrupted
communication, do not talk on a channel if someone else is currently talking on it. To check for
activity on a channel before you talk, press and hold mon/ key. If you hear static, the channel
is clear to use.
Removing Channels form the Scan List
To remove a channel so the radio does not stop on it while scanning, press and hold or
for at least 3 seconds, then release. This temporarily removes the channel from the scan list.
To restore the channel, turn the radio off and then back on.
Note: You cannot remove the channel which your radio was set to (called your home channel)
when you start scanning.
9
Interference Eliminator Code (CTCSS)
CTCSS help minimize interference by providing you with a choice of code combinations.
1. Press mode/ until the code number begins to flash.
2. Press or to change the code.
3. Press to set new code.
You can specify a different code for each channel.
Note: You must set the CTCSS to 0 on a radio that uses CTCSS to communicate with other radios
that do not have CTCSS.
Time-out Timer
The time-out timer feature helps extend battery life by preventing accidental transmission. The
radio will emit a continuous warning tone after is pressed for 60 continuous seconds and will
stop transmitting.
Keypad Lock
To avoid accidentally changing your radio settings, press and hold mode/ for 3 seconds until
key lock icon is displayed. You can turn the radio on and off, adjust the volume, receive, transmit,
send a call tone and monitor channels. All other functions are locked.
10
To unlock the radio, press and hold mode/ for 3 seconds and until key lock icon is no longer
displayed.
Channel Busy Indicator
When a channel is busy, the LED flashes twice per second.
Setting and Transmitting Call Tone
Your radio can transmit different call tones to other radios in your group so you can alert them that
you want to talk.
To set a call tone:
1. With the radio on, press mode/ 3 times. The current call tone setting flashes and CA is
displayed.
2. Press or to change and hear the call tone.
3. Press mode/ or to set the new call tone.
To transmit your call tone to other radios set to the same channel and Interference Eliminator Code
as your radio, press CALL button.
Note: This radio has 10 call tones. Setting the call tone to 0 disables the call tone feature.
Transmitting a Talk Confirmation Tone
When you turn on this feature, your two-way radio transmits a unique tone when you finish
transmitting. It’s like saying 'Roger' or 'Over', and lets others know you’ve finished talking. And at
the same time, the icon will display.
1. To turn talk confirmation tone on, press and hold button while you turn the radio on.
11
When you release button after transmitting, your talk confirmation tone transmits.
2. To turn talk confirmation tone off, turn your radio off and then back on while pressing and
holding button.
Hands Free Use (VOX)
VOX allows you to transmit hands free by talking while using VOX accessories connected to the
radio.
1. Turn the radio off.
2. Insert the plug of the VOX accessory firmly into the accessory jack.
3. Turn the radio on and “VOX” is displayed.
4. Lower the radio volume before placing the accessory on your head or in your ear.
5. To transmit, speak into the accessory microphone. There is a short delay between the time
you start talking and radio transmission.
6. To receive, stop talking.
To turn VOX off, press or remove the VOX accessory.
Baby Monitor Feature
Your radios may be used as a baby monitor. To use this feature:
1. Turn off your radio.
2. Turn your radio on with button pressed.
12
The "VOX" icon will appear in the display to indicate that the baby monitor feature is
active.
To transmit, speak into the radio microphone. To receive, simply stop talking.
3. Pressing to transmit will disable the baby monitor feature.
4. Press button for a very short time to activate the baby monitor again. “VOX” will appear
on the screen again.
Note: When using the baby monitor feature, there is a short delay after you start talking, before the
radio transmits.
Setting Sensitivity Levels
Adjusting your radio’s sensitivity level helps minimize the possibility of unintended noise
triggering a transmission and helps the radio pick up soft voices.
1. Press mode/ 4 times or until the sensitivity level number and “VOX” is shown.
2. Press or to select the sensitivity level:
1 = Low Sensitivity (for noisy environments)
2 = Medium Sensitivity (for most environments)
3 = High Sensitivity (for quiet environments)
Note: When you connect a VOX accessory, the radio is automatically set to the last chosen
sensitivity level.
Battery Meter
13
The battery icon shows the battery charge level from full to empty.
When the battery is about to be empty, the radio chirps periodically.
Note: Remove the batteries before storing your radio for extended period of time. Batteries
corrode over time and may cause permanent damage to your radio.
Stopwatch
You can use your radio as a stopwatch. To use this feature:
1. With the radio on, press mode/ until "0" “00” appears in the display.
2. Press and the stopwatch will begin to run. Minutes and seconds will be shown.
3. While the stopwatch is running, pressing will pause it and display the time that has passed.
Note that the stopwatch doesn’t quit working; it still runs in the background. If is pressed
again, the stopwatch will continue running based on the time from the start of the stopwatch,
rather than the time that is shown in the pause state.
4. To reset the stopwatch, press while in the pause state.
5. Pressing or CALL will end the stopwatch feature and allow the radio to begin transmitting
again. If you press and hold the monitor key, the watch will stop and the radio will enter the
monitor state. Release Monitor/Scan to quit to standby state.
Note: This timer is for your reference only. When your radio is being used as a stopwatch, you will
not be able to use VOX or the baby monitor feature.
Using Audio Accessory (optional)
1. Turn the radio off. Plug the accessory connector into the jack.
2. Turn the radio on. Lower the volume before placing the accessory on your head or in your 14
ear.
3. Adjust the volume to a comfortable level using or .
4. To transmit, speak into the accessory microphone.
5. To receive, stop talking.
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1 this device may not cause harmful interference, and
2 this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
15
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
Warning:
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Any adjustment to this equipment is recommended to be performed by or under the immediate
supervision and responsibility of a person certified as technically qualified to perform transmitter
maintenance and repair duties in the private land mobile services and fixed services by an
organization or committee representative of users of those services.
Replacement of any transmitter component (crystal, semiconductor, etc.) for this equipment could
result in violation of FCC rules.
16