Giant Electronics MBADJ Two Way Radio with GMRS/FRS User Manual Layout 1

Download:
Mirror Download [FCC.gov]
Document ID	1194950
Application ID	r8Gvxmq9q88Yr0deHRU2DA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	161.84kB (2022947 bits)
Date Submitted	2009-11-05 00:00:00
Date Available	2009-11-05 00:00:00
Creation Date	2009-08-21 14:47:08
Producing Software	QuarkXPress(R) 7.2
Document Lastmod	2009-08-21 14:47:08
Document Title	Layout 1
Document Creator	QuarkXPress(R) 7.2

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of
limitation of exposure to electrical, magnetic and electromagnetic
fields in the radio frequency range between 9 KHz and 300GHz”.
To ensure optimal radio performance and make sure human exposure
to radio frequency electromagnetic energy is within the guidelines set
forth in the above standards, always adhere to the following
procedures.
Two-Way Radio
User’s Guide
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage
the radio and may violate FCC regulations.
Do NOT hold the antenna when the radio is “IN USE.” Holding the
antenna affects the effective range.
Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
guidelines, if you wear a radio on your body when transmitting, always
place the radio in a Motorola-supplied or approved clip, holder, holster,
case or body harness for this product. Use of non-Motorola-approved
accessories may exceed FCC/Health Canada RF exposure guidelines.
If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use
position, ensure the radio and its antenna are at least 1 inch (2.5 cm)
from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without
an accessory cable, position the radio and its antenna at least one
inch (2.5 cm) from the body.
KEM-ML36000
MB Series
The MB Series is approved for use in the US only.
Approved Accessories
For a list of approved Motorola accessories, visit out Web site at
www.motorola.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. This device complies
with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts,
turn off your radio in any facility where posted notices instruct you to
do so. Hospitals or health care facilities may be using equipment that
is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard on aircraft.
Any use of a radio must be in accordance with applicable regulations
per airline crew instructions.
For More Information
For further information, you may call Motorola at 1-800-638-5119 (U.S.),
e-mail us at giantintl@callcenter.com or visit us on the Internet at
www.motorola.com.
Safety and General Information
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations
are consistent with the independent research by and
recommendations of the U.S. Food and Drug Administration.
People with pacemakers should:
• ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
• Use the ear opposite the pacemaker to minimize the potential for
interference.
The information provided in this document supersedes the general
safety information in user guides published prior to December 1, 2002.
• Turn the radio OFF immediately if there is any reason to suspect that
interference is taking place.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control
your exposure and ensure compliance with the general
population/uncontrolled environment exposure limits, always adhere to
the following procedure:
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In
the event of such interference, you may want to consult your hearing
aid manufacturer to discuss alternatives.
• Transmit no more than 50% of the time.
• To receive calls, release the Push-to-Talk (PTT) button.
• To transmit (talk), press the PTT button.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting (in
terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines:
Medical Devices - Other
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately shielded
from RF energy. Your physician may be able to assist you in obtaining
this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the area
where you drive, and always obey them. If you do use your radio while
driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• United States Federal communications Commission, Code of Federal
Regulations; 47CFR part 2 sub-part J.
• Pull off the road and park before making or answering a call if
driving conditions so require.
• American National Standards Institute (ANSI)/Institute of Electrical
and Electronic Engineers (IEEE) C95. 1-1992.
The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your ability to
safely participate in such activities. Always use technology safely.
• Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999
Edition.
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998.
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
to Radiofrequency Electromagnetic Fields in the Frequency Range
from 3 KHz to 300 GHz, 1999.
• Australian communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
Do not place a portable radio in the area over an air bag or in the air
bag deployment area. Air bags inflate with great force. If a portable
radio is placed in the air bag deployment area and the air bag inflates,
the radio may be propelled with great force and cause serious injury to
occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
atmosphere. Only radio types that are especially qualified should be
used in such areas as “Intrinsically Safe.” Do not remove, install or
charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or
even death.
Note: The areas with potentially explosive atmospheres referred to
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and any
other area where you would normally be advised to turn off your vehicle
engine. Areas with potentially explosive atmospheres are often—but not
always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area, or in
areas posted “Turn off two-way radios.” Obey all signs and instructions.
Removing the NiMH Battery Pack (Optional Accesory)
1. Turn the radio off.
Control Buttons
3. Gently remove the NiMH battery by easing it out.
4. Reposition the battery cover and press down to secure.
Scroll
Batteries
All batteries can cause property damage and/or bodily injury such as
burns if a conductive material—like jewelry, keys or beaded chains—
touch exposed terminals. The conductive material may complete an
electrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
pocket, purse or other container with metal objects.
MENU
Removing the Three AAA Alkaline Batteries
1. Turn the radio off.
MENU
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
PTT
Microphone
MENU
Power/Menu/Lock
Speaker
Audio Accessory Jack
Recharging Jack
4. Reposition the battery cover and press down to secure.
Channel
Notes:
• Excercise care when removing NiMH or AAA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
• Remove the batteries before storing your radio for extended periods
of time. Batteries corrode over time and may cause permanent
damage to your radio.
Using the Plug-in Charging Adaptor (Optional Accesory)
The battery plug-in charger (adaptor) provides charging convenience
for NiMH batteries in one or both radios. Charge the NiMH battery
overnight (at least 16 hours) before using it for the first time. After the
initial charge, an empty battery is fully charged within 14 hours.
Battery Charger Safety Instructions:
3. Plug the AC power supply into a standard wall outlet.
Save these Instructions
Notes:
• The light will remain red after the battery pack is fully charged.
• When moving between hot and cold temperatures, do not charge
the battery until the battery temperature acclimates (usually about
20 minutes).
• For optimal battery life, unplug the charging adaptor within 16 hours.
Do not store the radio while connected to the charger.
• When your radio is plugged into the AC power adaptor, your radio will
automatically power off.
Display Screen Guide
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will
not fit the outlet, have the proper outlet installed by a qualified
electrician. An improper condition can result in a risk of electric
shock.
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC receptacle.
7. Make sure the cord is located so it will not be stepped on, tripped
over or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of a fire
and/or electric shock. If an extension cord must be used, make sure
that:
• The pins on the plug of the extension cord are the same number, size
and shape as those on the plug of the charger.
Low Battery Alert
In addition to your battery meter showing how much battery power you
have, your radio will beep to alert you to the fact that your batteries
are low.
Numbers for Channel,
Call Tones
– Battery Meter
Turning Your Radio On and Off
– Transmitting
– Lock
– Receiving
– On/Off for each
feature
– Auto Power On/Off
– Scan
• The extension cord size is 18 AWG for lengths up to 100 feet, and
16 AWG for lengths up to 150 feet.
– Call Tone, Keypad Tone
– Volume
1-202-418-0177
1-800-418-FORM
(3676)
Installing the Batteries
Each radio uses 1 NiMH rechargeable battery pack or 3 AAA alkaline
batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
If you have
questions about
the FCC License:
Call the FCC
3. Remove the NiMH battery pack from the clear plastic bag (do not
disassemble or unwrap the battery pack).
1-888-CALL-FCC
(225-5322)
Installing the Three AAA Alkaline Batteries (Not Included)
1. Turn the radio off.
Changes or modifications not expressly approved by Motorola may void
the user’s authority granted by the FCC to operate this radio and should
not be made. To comply with FCC requirements, transmitter adjustments
should be made only by or under the supervision of a person certified as
technically qualified to perform transmitter maintenance and repairs in
the private land mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not authorized by
the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be
distributed is subject to government regulations and may be prohibited.
until a channel number appears
MENU
until the display goes blank.
Setting the Volume
Press
to increase or
to decrease the volume. The volume level
flashes and VOL displays.
462.5625
FRS
12
467.6625
FRS
462.5875
FRS
13
467.6875
FRS
462.6125
FRS
14
467.7125
FRS
462.6375
FRS
15
462.5500
GMRS
462.6625
FRS
16
462.5750
GMRS
462.6875
FRS
17
462.6000
GMRS
462.7125
FRS
18
462.6250
GMRS
467.5625
FRS
19
462.6500
GMRS
467.5875
FRS
20
462.6750
GMRS
10
467.6125
FRS
21
462.7000
GMRS
11
467.6375
FRS
22
462.7250
GMRS
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group
so you can alert them that you want to talk. You have 10 call tones from
which to choose.
To set a call tone:
1. With the radio on, short press
until the
appears. The current
call tone setting flashes.
2. Press
or
to change and hear the call tone.
MENU
3. Press PTT to set the new call tone or
to continue set up.
To transmit your call tone to other radios set to the same channel as
your radio, press .
MENU
Note: Setting the call to 0 disables the call tone feature.
Keypad Tones
You may enable or disable the speaker key tones. You will hear the key
tone each time a button is pushed.
1. Press
until
appears. The current setting On/Off will flash.
2. Press either
or
to turn On or Off.
3. Press PTT to confirm or
to continue set up.
MENU
Talking and Listening
To communicate, all radios in your group must be set to the same
channel.
PTT
For maximum clarity, hold the radio two to three inches away from your
mouth and speak directly into the microphone. Do not cover the
microphone while talking.
Getting Started
For mail service:
Call the FCC
Forms Hotline
MENU
1. To talk, press and hold PTT .
2. When you are finished talking, release
FCC Licensing Information
For a fax:
Contact the
Fax-0n-Demand
system
MENU
9. The supply cord of the AC adaptor cannot be replaced. If the cord is
damaged, call customer service at 1-800-638-5119 or e-mail us at
giantintl@callcenter.com.
If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
1. To turn on, press and hold
and the radio beeps.
2. To turn off, press and hold
– Talk Confirmation
Tone (Roger Beep)
• The extension cord is properly wired and in good electrical condition.
Your Motorola radio operates on General Mobile Radio Service (GMRS)
frequencies and is subject to the Rules and Regulations of the Federal
Communications Commission (FCC). The FCC requires that all operators
using GMRS frequencies obtain a radio license before operating their
equipment. To obtain the FCC forms, please visit the FCC’s Web site at
wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159,
which includes all the instructions you will need.
Frequency
Frequency
Description Channel
Description
(MHz)
(MHz)
1. Follow the steps above to install a NiMH battery pack.
2. Connect the AC power adaptor plug into the recharging jack at the
bottom (right) of the radio. (The adaptor charges two radios.)
6. Use of an attachment not recommended or sold by Motorola may
result in a risk of fire, electric shock or personal injury.
Channels and Frequencies
3. Remove each alkaline battery by easing each battery out
individually.
Push-to-Talk
(PTT)
Exercise care when removing NiMH or AAA batteries. Do not use sharp
or conductive tools to remove either of these batteries.
5. To reduce the risk of electric shock, unplug the charger from the
outlet before attempting any maintenance or cleaning.
Selecting the Channel
Your radio has 22 channels. The channel is the frequency your radio
uses to transmit. (See Channels and Frequencies table below.)
. The channel number flashes.
1. Briefly press and release
or
to select a channel.
2. Press
to continue set up.
3. Press PTT to confirm or
Call Tone
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged
antenna comes into contact with your skin, a minor burn can result.
Menu Options
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
4. Insert the NiMH battery pack with the diagram facing you.
5. Reposition the battery cover and press down to secure.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Insert the three AAA alkaline batteries with + and - polarity as
shown inside.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Note: This radio does not have Interference Eliminator Codes. To
communicate with radios that use Interference Eliminator Codes, the
Interference Eliminator Code must be set to 0.
Monitor Button
Use this feature to see if there is anyone on the channel you have
selected.
1. Short press
until RX appears.
2. When you finish listening, press PTT to confirm or
to continue
set up.
MENU
MENU
Note: Monitor will time out after five seconds if
pressed.
PTT
or
MENU
is not
Push-to-Talk PTT Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you press
PTT for 60 continuous seconds.
Note: When the key tone feature is off, the following are not disabled:
• Transmit timeout alert tone
• Power-down alert tone
• Low battery alert tone
• The transmitted talk confirmation tone
Transmitting a Talk Confirmation Tone
You can set your radio to transmit a unique tone when you finish
transmitting. It is like saying “Roger” or “Over” to let others know you
are finished talking.
1. With the radio on, short press
until
appears. The current
setting On/Off flashes.
2. Press
or
to turn On or Off.
3. Press PTT to set the talk confirmation tone or
to continue
set up.
MENU
MENU
Auto Power On/Off
Your radio will save power by automatically turning itself off if unused
after a predetermined amount of time.
1. Activate this setting by short pressing
until displays. The
current setting (0, 30, 60, 90) will flash.
2. Press
or to set the time to 30 minutes, 60 minutes or
90 minutes.
3. When you exit the Menu mode, the setting timer will begin if you are
not using the radio.
4. The screen shows
5. Press PTT to confirm or
to continue set up.
MENU
MENU
4. Reposition the battery cover and press down to secure.
Radio Battery Meter
The radio battery icon shows the radio battery charge level, from full
to empty
. When the radio has one segment left, the
radio chirps periodically or after releasing PTT (Low Battery Alert).
Continued on back
MB Series
Special Features
Keypad Lock
To avoid accidentally changing your radio settings you can lock your
keypad:
1. Short press
until
appears. The current setting On/Off
will flash.
or
to turn On or Off.
2. Push
will be displayed on your screen.
3. The
MENU
When in lock mode, you cannot adjust the volume, but all other
functions work as usual.
To unlock the radio, press and hold
MENU
for a few seconds.
Scanning Channels
Use scanning to monitor channels for transmissions or to find someone
in your group who has accidentally changed channels.
1. Briefly press
will flash.
2. Press either
3. Press
PTT
MENU
until
or
appears. The current setting On/Off
Warranty
Products Covered
Length of Coverage
Consumer Two-Way Radio Products and Accessories purchased in
the United States.
Products and Accessories as
defined above, unless otherwise
provided for below.
One (1) year from the date of
purchase by the first consumer
purchaser of the product unless
otherwise provided for below.
1. Consumer Two-Way Radio
Accessories.
1. Ninety (90) days from the
date of purchase by the first
consumer purchaser of the
product.
What Does this Warranty Cover?
Subject to the exclusions contained to the right, Giant International
Ltd. warrants the Motorola branded consumer two-way radios that
operate via Family Radio Service or General Mobile Radio Service
that it manufactures (“Products”) and the the Motorola branded or
certified accessories sold for use with these Products that it
manufactures (“Accessories”) to be free from defects in materials
and workmanship under normal consumer usage for the period(s)
outlined below. This limited warranty is a consumer’s exclusive
remedy, and applies as follows to new Motorola branded Products
and Accessories manufactured by Giant International Ltd., and
purchased by consumers in the United States, which are
accompanied by this written warranty:
2. Products and Accessories
that are Repaired or
Replaced.
2. The balance of the original
warranty or for ninety (90)
days from the date returned
to the consumer, whichever
is longer.
to turn On or Off.
to confirm or
MENU
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper
operation, storage, misuse or abuse, accident or neglect, such as
physical damage (cracks, scratches, etc.) to the surface of the
product resulting from misuse; (b) contact with liquid, water, rain,
extreme humidity or heavy perspiration, sand, dirt or the like, extreme
heat, or food; (c) use of the Products or Accessories for commercial
purposes or subjecting the Product or Accessory to abnormal usage
or conditions; or (d) other acts which are not the fault of Motorola or
Giant International Ltd., are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects
or damage that result from the use of Non-Motorola branded or
certified Products, Accessories, or other peripheral equipment are
excluded from coverage.
to continue set up.
When the radio detects channel activity, it stops scanning and you can
hear the transmission. To respond, press PTT within five seconds.
Advanced Scan
If the radio stops on an undesired transmission, you may immediately
or
resume the scan by briefly pressing
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by someone
other than Motorola, Giant International Ltd. or its authorized
service centers, are excluded from coverage.
Use With Accessories
You can transmit more reliably with the use of optional PTT headset
accessories. A PTT headset allows privacy to others around you while
listening.
Many accessories (sold separately) are available for your radio. For
more information, visit our Web site at www.motorola.com or
shop.giantintl.com.
Altered Products. Products or Accessories with (a) serial numbers
or date tags that have been removed, altered or obliterated; (b)
broken seals or that show evidence of tampering; (c) mismatched
board serial numbers; or (d) nonconforming or non-Motorola
branded housings, or parts, are excluded from coverage.
1. Turn the radio off and plug the PTT accessory into the accessory
jack.
2. Turn the radio on. You may now press the PTT on the accessory
microphone instead of the radio.
3. Adjust the volume appropriately by pressing
. Lower the volume
before placing the accessory on your head or in your ear.
Communication Services. Defects, damages, or the failure of
Products or Accessories due to any communication service or
signal you may subscribe to or use with the Products or
Accessories is excluded from coverage.
Note: The MB Series does not have VOX capabilities, and is only
compatible with PTT headset accessories.
Who is covered?
This warranty extends only to the first consumer purchaser, and is
not transferable.
What will GIANT INTERNATIONAL LTD. do?
GIANT INTERNATIONAL LTD., at its option, will at no charge repair,
replace or refund the purchase price of any Products or
Accessories that does not conform to this warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned or
new Products, Accessories or parts.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
USA Two-Way Radios
1-800-638-5119
giantintl@callcenter.com
For Accessories, please call the telephone number designated
above for the product with which they are used.
You will receive instructions on how to ship the Products or
Accessories at your expense, to a GIANT INTERNATIONAL LTD.
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL
MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE, WHETHER
IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES
IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR
ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE
OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR
ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from state
to state or from one jurisdiction to another.
Patent and Copyright Information
Manufactured, distributed or sold by Giant International Ltd., official
licensee for this product. Motorola, the Stylized M Logo, and other
Motorola trademarks and trade dress are owned by Motorola, Inc.
and are used under license from Motorola, Inc. MOTOROLA and the
Stylized M Logo are registered in the US Patent & Trademark Office.
All other product or service names are the property of their
respective owners. ©Motorola, Inc. 2010. All rights reserved.
Please contact customer service at 1-800-638-5119 or e-mail us
at giantintl@callcenter.com for questions/comments, warranty,
support or service related to this product.
MB Series

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%MarksAllSeparations: true.%%EndComments
Creator                         : QuarkXPress(R) 7.2
Modify Date                     : 2009:08:21 14:47:08
Create Date                     : 2009:08:21 14:47:08
Producer                        : QuarkXPress(R) 7.2
Title                           : Layout 1

EXIF Metadata provided by EXIF.tools