Giant Electronics MRCEE Two Way Radio with GMRS, FRS, and Weather Band Rx User Manual Layout 1

Download:
Mirror Download [FCC.gov]
Document ID	1098468
Application ID	2Hm89UFlCfEfiw3eWuxtwA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.78kB (284711 bits)
Date Submitted	2009-04-17 00:00:00
Date Available	2009-04-17 00:00:00
Creation Date	2009-01-06 17:00:24
Producing Software	QuarkXPress(R) 7.2
Document Lastmod	2009-01-06 17:01:25
Document Title	Layout 1
Document Creator	QuarkXPress(R) 7.2

Do NOT hold the antenna when the radio is “IN USE.” Holding the
antenna affects its effective range.
®
Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
guidelines if you wear a radio on your body when transmitting always
place the radio in a Motorola-supplied or approved clip holder, holster,
case or body harness for this product. Use of non-Motorola-approved
accessories may exceed FCC/Health Canada RF exposure guidelines.
Two-Way Radio
User’s Guide
If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use position,
ensure the radio and its antenna are at least 1 inch (2.5 cm) from your
body when transmitting.
Approved Accessories
For a list of approved Motorola accessories, visit our Web site at
www.motorola.com.
Batteries
All batteries can cause property damage and/or bodily injury such as burns
if a conductive material—like jewelry, keys or beaded chains— touch
exposed terminals. The conductive material may complete an electrical
circuit (short circuit) and become quite hot. Exercise care in handling any
charged battery, particularly when placing it inside a pocket, purse or other
container with metal objects.
2. This device must accept any interference received, including
interference that may cause undesired operation.
IC Canada
The term "IC:" before the equipment certification number only signifies
that the Industry Canada technical specifications were met.
For More Information
For further information, you may call Motorola at 1-800-638-5119 (U.S.
and Canada), or e-mail us at giantintl@callcenter.com or visit us on the
Internet at www.motorola.com.
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety
information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control your
exposure and ensure compliance with the general population/
uncontrolled environment exposure limits, always adhere to the following
procedure:
•
Transmit no more than 50% of the time.
•
To receive calls, release the PTT button.
•
To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting (in
terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines:
•
United States Federal Communications Commission, Code of Federal
Regulations; 47CFR part 2 sub-part J.
•
American National Standards Institute (ANSI)/Institute of Electrical
and Electronic Engineers (IEEE) C95. 1-1992.
•
Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn
off your radio in any facility where posted notices instruct you to do so.
Hospitals or health care facilities may be using equipment that is
sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard an aircraft.
Any use of a radio must be in accordance with applicable regulations
per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
consistent with the independent research by and recommendations of
the U.S. Food and Drug Administration.
People with pacemakers should:
•
•
Use the ear opposite the pacemaker to minimize the potential for
interference.
•
The extension cord size is 18 AWG for lengths up to 100 feet, and
16 AWG for lengths up to 150 feet.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the area
where you drive, and always obey them. If you do use your radio while
driving, please:
Give full attention to driving and to the road.
•
Use hands-free operation, if available.
•
Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
to Radiofrequency Electromagnetic Fields in the Frequency Range
from 3 KHz to 300 GHz, 1999.
•
Pull off the road and park before making or answering a call if driving
conditions so require.
ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of
limitation of exposure to electrical, magnetic and electromagnetic fields
in the radio frequency range between 9 KHz and 300GHz”.
To ensure optimal radio performance and make sure human exposure to
radio frequency electromagnetic energy is within the guidelines set forth
in the above standards, always adhere to the following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage the
radio and may violate FCC regulations.
The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your ability to
safely participate in such activities. Always use technology safely.
Do not place a portable radio in the area over an air bag or in the air bag
deployment area. Air bags inflate with great force. If a portable radio is
placed in the air bag deployment area and the air bag inflates, the radio
may be propelled with great force and cause serious injury to occupants
of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
atmosphere. Only radio types that are especially qualified should be
used in such areas as “Intrinsically Safe.” Do not remove, install or
charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or
even death.
Push to Talk
(Low)
9. The supply cord of the AC adaptor cannot be replaced. If the cord is
damaged, call customer service at 1-800-638-5119 (U.S. and Canada)
or e-mail us at giantintl@callcenter.com.
FCC Licensing Information
Your Motorola radio operates on General Mobile Radio Service (GMRS)
frequencies and is subject to the Rules and Regulations of the Federal
Communications Commission (FCC). The FCC requires that all operators
using GMRS frequencies obtain a radio license before operating their
equipment. To obtain the FCC forms, please visit the FCC’s Web site at
wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159,
which includes all the instructions you will need.
If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
For a fax:
Contact the
Fax-0n-Demand
system
1-202-418-0177
For mail service:
Call the FCC
Forms Hotline
1-800-418-FORM
(3676)
If you have
questions about
the FCC License:
Call the FCC
1-888-CALL-FCC
(225-5322)
Changes or modifications not expressly approved by Motorola may void
the user’s authority granted by the FCC to operate this radio and should
not be made. To comply with FCC requirements, transmitter adjustments
should be made only by or under the supervision of a person certified as
technically qualified to perform transmitter maintenance and repairs in
the private land mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not authorized by
the FCC equipment authorization for this radio could violate FCC rules.
4. Reposition the battery cover and press down to secure.
For maximum clarity, hold the radio two to three inches away from your
mouth and speak directly into the microphone. Do not cover the
microphone while talking.
Accessory Jack
Flashlight Button
Microphone
Scan/Monitor
Call Tone
Menu/Lock
Remove the batteries before storing your radio for extended periods
of time. Batteries corrode over time and may cause permanent
damage to your radio.
Using the Battery Charger (Optional Accessory)
The battery charger provides drop-in charging convenience for NiMH
batteries and can be placed on any flat surface, such as a desk or
workbench. Charge the NiMH battery overnight (at least 16 hours) before
using it for the first time. After the initial charge, an empty battery is fully
charged within 14 hours.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
Scroll/Weather
3. Plug the AC power supply into a standard wall outlet.
Mini-USB
Charging Port
4. With a radio facing forward, slide it into one of the charging pockets.
Flashlight LED
Numbers for Channel,
Call Tone
5. When charging in the battery charger, the red light on the charger
base will glow continuously.
Using the mini-USB Charging Connector
The mini-USB charging connector is a handy port that allows you to
conveniently charge your NiMH battery pack. This is an alternative to
charging your NiMH battery pack in the Battery Charger desk stand
using the AC wall adaptor and especially useful when used while
traveling.
Available mini-USB charging options (Optional Accessories):
1. Wall travel charger
Numbers for Codes
2. Vehicle charger
3. Mini-USB computer cable
— Battery Meter
— Scan
— Channel Power
Indicator
(see Menu Options)
— Vibrate
If using a computer, the computer must be turned on.
This and other accessories (sold separately) are available for your radio.
For more information, visit our Web site at www.motorola.com or
shop.giantintl.com.
— Call Tone,
Keypad Tone
— Noise Filtering
— Repeater Channels
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Power Boost
To boost your radio’s power up to high power, press the top portion of the
button when talking. If you know your party is close by, you can
conserve your battery’s energy by pushing the lower part of the
button to use less power.
Note: If you are on an FRS only channel (see Channels and Frequencies
table) the radio will only use low power when either portion of the
is pressed.
Monitor Button
Pressing and holding
for three seconds allows you to listen to the
volume level of the radio when you are not receiving. This allows you to
adjust the volume, if necessary. You can also press
to check for
activity on the current channel before you talk.
Push to Talk
Timeout Timer
To prevent accidental transmissions and save battery life, the radio emits
a continuous warning tone and stops transmitting if you press
for 60
continuous seconds.
Menu Options
Selecting the Channel
Your radio has 22 channels plus 8 repeater channels. The channel is the
frequency the radio uses to transmit. Channels 8-14 are FRS 0.5 watt only
and all other channels are GMRS. (See the "Channels and Frequencies"
table on overleaf for details.)
1. With the radio on, press
watt channel,
channel,
. When the radio is on a 0.5
displays. When the radio is on a 1.5 watts
displays. The current channel flashes.
2. Press
or
2. Plug the cable into the mini-USB port on the bottom of your radio.
3. Press
to save the channel setting or
— Hands-Free Use
Without
Accessories
3. An empty battery will be fully charged in 14 hours.
— Hands-Free Use
With Accessories
Notes
• The light will remain red after the NiMH battery pack is fully charged.
Selecting the Interference Eliminator Code
Interference Eliminator Codes help minimize interference by blocking
transmissions from unknown sources. Your radio has 121 Interference
Eliminator Codes. Codes 1 – 38 are the standard analog codes that
appear on other FRS/GMRS radios. Codes 39 – 121 are additional digital
codes added for superior interference protection. 0 is the off position, no
analog or digital codes are enabled.
— Weather Alert
— Talk Confirmation
Tone (Roger Beep)
2. When you are finished talking, release
1. Plug your mini-USB cable or charger into a power source as is
appropriate for your accessory.
— Lock
7. Make sure the cord is located so it will not be stepped on, tripped
over or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of a fire
and/or electric shock. If an extension cord must be used, make sure
that:
1. To talk, press and hold
Notes
• Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
LED Indicator
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
3. Gently remove each alkaline battery by easing each battery out
individually.
•
6. Use of an attachment not recommended or sold by Motorola may
result in a risk of fire, electric shock or personal injury.
The extension cord is properly wired and in good condition.
Medical Devices – Other
If you use any other personal medical device, consult the manufacturer
of your device to determine if it is adequately shielded from RF energy.
Your physician may be able to assist you in obtaining this information.
Push to Talk
(High)
5. To reduce the risk of electric shock, unplug the charger from the
outlet before attempting any maintenance or cleaning.
•
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the
event of such interference, you may want to consult your hearing aid
manufacturer to discuss alternatives.
Emergency Alert
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC
receptacle.
Not carry the radio in the breast pocket.
•
•
3. Never alter the AC cord or plug provided with the unit. If the plug will
not fit the outlet, have the proper outlet installed by a qualified
electrician. An improper condition can result in a risk of electric
shock.
•
Turn the radio OFF immediately if there is any reason to suspect that
interference is taking place.
Volume
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
Talking and Listening
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
MR350
/ MR355 LCD LINE ART
Display Screen
Guide
The pins on the plug of the extension cord are the same number,
size and shape as those on the plug of the charger.
•
Removing the Three AA Alkaline Batteries
1. Turn the radio off.
Control
Buttons
MR350R Radio
line drawing
Battery Charger Safety Instructions:
Save these Instructions
•
International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998.
Australian Communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
Exercise care when removing NiMH or AA batteries. Do not use sharp or
conductive tools to remove either of these batteries.
ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
•
•
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn can
result.
1. This device may not cause harmful interference; and
KEM-PK14190-94
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area, or in
areas posted “Turn off two-way radios.” Obey all signs and instructions.
Data Operation
If applicable, when using any data feature of the radio with or without an
accessory cable, position the radio and its antenna at least one inch
(2.5 cm) from the body.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
MR355
Note: The areas with potentially explosive atmospheres referred to above
include fueling areas such as below decks on boats, fuel or chemical
transfer or storage facilities, areas where the air contains chemicals or
particles (such as grain, dust or metal powders) and any other area
where you would normally be advised to turn off your vehicle engine.
Areas with potentially explosive atmospheres are often—but not
always—posted.
— On/Off for each
feature
Getting Started
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3 AA
alkaline batteries and beeps when the batteries are low.
4. The LED indicator light on the radio will glow to indicate that the
battery is charging.
•
When moving between hot and cold temperatures, do not charge the
NiMH battery pack until the battery temperature acclimates (usually
about 20 minutes).
•
For optimal battery life, remove the radio from the charger within 16
hours. Do not store the radio while connected to the charger.
•
If the radio is kept on while charging, the charging time will be
extended.
•
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch up
and remove the cover.
3. Remove the NiMH battery pack from the clear plastic bag (do not
disassemble or unwrap the battery pack).
Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty
. Allow
time for the battery to charge to 1 bar
before attempting to
transmit a message.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
4. Insert the NiMH battery pack with the diagram facing you. (The
ribbon should be underneath the battery pack and should wrap
around the right side of the pack for easy removal.)
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to release
the catch.
5. Reposition the battery cover and press down to secure.
Installing the Three AA Alkaline Batteries
1. Turn the radio off.
2. Pull the belt clip away from the back of the radio.
and select an unused or quiet channel.
to continue set up.
To set the code for a channel:
1. Press
until the code starts to flash.
2. Press
or
3. Press
to save the code setting or
to select the code.
to continue set up.
You can set a different code for each channel using this procedure. An
extended press of
or
allows you to scroll through the Interference
Code rapidly so you can quickly reach the code you want.
Note: You must set the Interference Eliminator Code to 0 on a radio that
uses Interference Eliminator Codes to communicate with radios that do
not have Interference Eliminator Codes. Select 0 for “no tone, no code”
and OFF will flash on your radio’s display.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group
so you can alert them that you want to talk. Your radio has 10 call tones
from which to choose, including 5 animal sounds and 5 regular call tones.
To set a call tone:
1. Press
three times until the current call tone setting flashes and
appears.
2. With the back of the radio facing you, lift the battery cover latch up
and remove the cover.
Turning your Radio On and Off
Turn
clockwise to turn the radio on and counterclockwise to turn the
radio off.
3. Insert the three AA alkaline batteries with + and - polarity as shown
inside. (The ribbon should be underneath the AA alkaline batteries
and should wrap around the right side of the batteries.)
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
To transmit your call tone to other radios set to the same channel and
Interference Eliminator Code as your radio, press
4. Reposition the battery cover and press down to secure.
2. The display screen then shows the current channel, code and all
features that are enabled.
Note: Setting the call to 0 disables the call tone feature.
Setting the Volume
Press and hold
for three seconds while rotating
comfortable listening level.
Hands-Free Use Without Accessories (
You can use the iVOX feature to transmit hands-free without the need for
any headset accessories. Once iVOX is turned on, the radio detects your
voice and transmits when you speak into the internal microphone.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
empty
. When the radio has one segment left, the
radio chirps periodically or after releasing
(Low Battery Alert).
Removing the NiMH Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
to
until you reach a
1. Rotate
clockwise to increase the volume.
2. Rotate
counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
3. Remove the NiMH battery pack by pulling the ribbon attached to
the radio.
2. Press
or
3. Press
to set the new call tone or
to change and hear the call tone.
1. Press
until
On/Off will flash.
2. Press
or
3. Press
to set or
to continue set up.
appears on the display. The current setting
to select On or Off.
to continue set up.
Continued on back
MR355
4. Reposition the battery cover and press down to secure.
Talking and Listening
Hands-Free Use With Accessories (
You can transmit hands-free more reliably with the use of optional
headset accessories. Once VOX is turned on, the radio detects your
voice and transmits when you speak.
Many accessories (sold separately) are available for your radio. For
more information, visit our Web site at www.motorola.com or
shop.giantintl.com.
1. Turn the radio off and plug the VOX accessory into the accessory port.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by rotating
. Lower the volume
before placing the accessory on your head or in your ear.
4. To turn off, simply remove accessory.
Note: There is a short delay between the time you start talking and when
the radio transmits. There is a short delay before the transmission is
completed.
Setting the Sensitivity Level When in
Mode
Adjusting the radio’s sensitivity level helps minimize the possibility of
unintended noises triggering a transmission and helps the radio pick up
soft voices.
1. Press
display.
2. Press
3. Press
until VOX and the level setting (1 - 3) appear on the
or
to select the sensitivity level.
to set or
to continue set up.
3 = High Sensitivity for quiet environments
1 = Low Sensitivity for noisy environments
Note: When you connect a headset, the radio is automatically set to the
last chosen sensitivity level.
QT Noise Filtering
The QT noise-filtering feature helps to ensure uninterrupted
communication with other Motorola radios that have this feature.
This feature also filters out unwanted transmissions from other
radios. This is useful in places where there is heavy radio traffic,
such as amusement parks or ski resorts.
Note: QT noise filtering is not available when the radio is scanning.
To turn QT noise filtering on or off:
1. Press
until
displays. The current setting On/Off will flash.
or
3. Press
to confirm your selection or
to turn noise filtering On or Off.
to continue set up.
To transmit to a radio that has QT noise filtering turned on:
1. Select the same channel and Interference Eliminator Code as
the other radio.
2. Press
to send a call tone. This allows your voice to pass
through the QT noise filter on the receiving radio.
3. Press
and speak normally.
Note: If you skip step 2, the beginning of your message may not be
heard on the receiving radio. For a 30-second period, starting after
the last transmission, all transmissions received on the selected
channel and code will pass through the QT noise filter.
VibraCallTM Alert
VibraCallTM is a vibrating alert that notifies you that your radio is
receiving a message. This is useful in noisy environments. When the
alert is on, the radio vibrates once every 30 seconds when you receive a
message on the channel and code you set.
1. To turn vibrating alerts on, press
current setting will flash.
2. Press
or
3. Press
to set or
until
is displayed. The
to change the setting to On/Off.
to continue set up.
Keypad Tones
You may enable or disable the speaker key tones. You will hear the key
tone each time a button is pushed.
1. Press
until
2. Press either
3. Press
appears. The current setting On/Off will flash.
or
to turn On or Off.
to confirm or
to continue set up.
Note: When the key tone feature is off, the following are not disabled:
•
•
•
•
Transmit timeout alert tone
Call tone
Low battery alert tone or
The transmitted talk confirmation tone
Transmitting a Talk Confirmation Tone
You can set your radio to transmit a unique tone when you finish
transmitting. It is like saying “Roger” or “Over” to let others know you
are finished talking.
1. With the radio on, press
On/Off flashes.
2. Press
or
3. Press
to set or
until the
appears. The current setting
to turn On or Off.
to quit menu mode.
Special Features
1. Press and hold the Emergency Alert button for 3 seconds.
2. Release the button after the LED Indicator glows red and the alert tone
begins to sound. There is no need to continue to hold the Emergency
Alert button or use PTT for your message to be transmitted.
3. After the alert tone ends you may speak into the microphone. Your
voice or incidental sounds will be transmitted. The LED indicator will
continue to glow for the duration of the 22 second period.
4. After 30 seconds your radio speaker will emit a Talk Confirmation
Tone and the LED Indicator will extinguish. Operation then returns to
normal two-way mode.
Note: All Motorola Talkabout EM, MJ, and MR series radios are fully
compatible with the Emergency Alert feature. Radios other than EM, MJ,
MR series can receive the emergency alert signal, but will not respond
with adjusted volume settings, locked controls, or a warbling alert tone.
Users of other radio models set to the same channel and Interference
Eliminator Code will hear a steady tone for 8 seconds followed by the
voice transmission for 22 seconds.
Warning: The Emergency Alert feature should only be used in the event
of an actual emergency. Motorola is not responsible if there is no
response to the emergency alert from the receiving group.
2 = Medium Sensitivity for most environments
2. Press
Emergency Alert Mode
The Emergency Alert feature can be used to signal members in your
group of your need for urgent help. MR series radios will operate in an
automatic “hands-free” emergency control mode for a total of 30
seconds after activating the Emergency Alert. MR series radios in your
group will automatically advance the speaker volume to the maximum
setting and sound a warbling alert tone for 8 seconds. The alert tone is
emitted from your own radio speaker and the receiving radios in your
group. After the 8 second alert, any spoken words or incidental sounds at
your end will be transmitted to the group for 22 seconds. For the 30
second duration of Emergency Alert mode, MR series radio controls and
buttons will be locked to maximize reception of the emergency message.
Built-in Flashlight
Press and hold the flashlight button to turn and keep the light on. The
switch functions as a momentary control for the light.
Note: Turn off the flashlight when not in use to conserve battery power.
Keypad Lock
To avoid accidentally changing your radio settings:
1. Press and hold
until
displays.
2. When in lock mode, you can turn the radio on and off, adjust the
volume, receive, transmit, send a call tone, and monitor channels. All
other functions are locked.
To unlock the radio, press and hold
until
is no longer displayed.
Scanning Channels
Use scan to search the 22 channels for transmissions from unknown
parties, to find someone in your group who has accidentally changed
channels, or to quickly find unused channels for your own use.
There is a priority feature and 2 modes of scanning (basic and
advanced) to make your search more effective. The basic scan mode
uses the channel and code combinations for each of the 22 channels as
you have set them (or with the default code value of 1). The “Advanced
Scan” mode will scan all channels for any and all codes, detect any
code in use, and use that code value temporarily for that channel.
Priority is given to the “home channel,” that is, the channel (and
Interference Eliminator Code) your radio is set to when you start the scan.
This means the initial channel (and code setting) is scanned more often
than the other 21 channels, and your radio will respond quickly to any
activity occurring on the home channel as a priority.
To start Scanning:
1. Briefly press the
key. The scan
will appear in the display, and the
radio will begin to scroll through the channel and code combinations.
2. When the radio detects channel activity matching the channel and
code combination, it stops scrolling and you can hear the
transmission.
3. To respond and talk to the person transmitting, press
seconds after the end of the transmission.
Channels and Frequencies
Warranty
FRS / GMRS SIMPLEX CHANNELS
Channel
Service Description
Frequency (MHz)
GMRS/FRS
462.5625
GMRS/FRS
462.5875
GMRS/FRS
462.6125
GMRS/FRS
462.6375
GMRS/FRS
462.6625
GMRS/FRS
462.6875
GMRS/FRS
462.7125
FRS
467.5625
FRS
467.5875
10
FRS
467.6125
Your radio can tune in to broadcasts by the United States National Oceanic
and Atmospheric Administration (NOAA) Weather Radio and Environment
Canada Weatheradio.
You can listen to a weather channel (see “Weather Channels and
Frequencies” table below) or set your radio to alert you to emergency
weather broadcasts that interrupt routine broadcasts. When you listen to a
weather channel, you cannot use your radio in scan mode or for two-way
communications.
11
FRS
467.6375
12
FRS
467.6625
13
FRS
467.6875
14
FRS
467.7125
15
GMRS
462.5500
16
GMRS
462.5750
17
GMRS
462.6000
Both NOAA and Environment Canada have transmitters located throughout
the United States and Canada, respectively. These transmitters broadcast
watches, forecasts, and other information 24 hours a day.
18
GMRS
462.6250
19
GMRS
462.6500
20
GMRS
462.6750
21
GMRS
462.7000
22
GMRS
462.7250
4. To restore the removed channel(s) to the scan list, turn the radio off
and then back on, or exit and re-enter the scanning mode by
pressing
5. You cannot remove the home channel from the scan list.
6. In Advanced Scan, the detected code will only be used for one
transmission. You must note the code, exit scan, and set that
detected code on that channel to permanently use the detected code.
Weather Receiver
Note: NOAA weather radio stations are assigned to cover specific areas and
service may be limited. Please check with your local weather office for
frequency and details, or visit www.weather.gov/nwr in the US or
www.msc.ec.gc.ca/msb/weatheradio in Canada to view the appropriate
transmitter for your area.
The use of the NOAA logo does not provide an endorsement or implied
endorsement by NOAA’s National Weather Service, nor does the use of the
Weatheradio logo provide an endorsement or implied endorsement by
Environment Canada.
GMRS DUPLEX REPEATER CHANNELS
Channel
TX (MHz)
RX (MHz)
15 R
467.5500
462.5500
16 R
467.5750
462.5750
Turning Weather Channel Reception On and Off
1. To turn weather reception on, press
and hold for 3 seconds.
17 R
467.6000
462.6000
18 R
467.6250
462.6250
2. To turn off, press
19 R
467.6500
462.6500
20 R
467.6550
462.6750
21 R
467.7000
462.7000
22 R
467.7250
467.7250
or turn the radio off and then back on.
Setting the Weather Channel
Your radio receives weather frequencies:
1. After turning weather reception on, press
channel flashes.
. The current
2. Press
or
to select the appropriate channel with good
reception in your area.
3. Press
to save the weather channel setting.
Setting the Weather Alert
Your radio can be set to respond to NOAA Weather Radio emergency
messages. A special alarm tone sounds an alert and turns on the
weather receiver to give you immediate weather and emergency
information.
1. After turning weather reception on, press
2. Press
or
3. Press
twice. On/Off displays.
to select On/Off. If you activate Weather Alert and
return to two-way mode,
will display.
4. Press
to return to two-way mode.
As with two-way radio reception, weather channel reception depends on
how close you are to a transmitter and whether you are indoors or
outdoors. Because weather channels are transmitted without codes, they
may contain static or noise. Weather Alert will not function while actively
transmitting or receiving in two-way mode.
Weather
Channel
Frequency
WX1
162.550 MHz
WX7
162.525 MHz
WX2
162.400 MHz
WX8
161.650 MHz
2. Briefly press the
key. The scan
will appear in the display, and
the radio will begin to scroll through the channels. No Interference
Eliminator Codes will filter what is heard.
WX3
162.475 MHz
WX9
161.775 MHz
WX4
162.425 MHz
WX10
161.750 MHz
3. When the radio detects channel activity with ANY code (or NO
code), it stops scrolling and you can hear the transmission. Any
Interference Eliminator Code that may be in use by that party will be
detected and displayed.
WX5
162.450 MHz
WX11
162.000 MHz
4. To respond and talk to the person transmitting, press
within five
seconds of the end of the transmission. The radio will transmit using
the newly detected Interference Eliminator Code.
5. The radio will resume scrolling through the channels five seconds
after the end of any received activity.
key.
Scanning Notes:
1. If you press
while the radio is scrolling through inactive
channels, the transmission will be on the “home channel”. Scanning
will resume five seconds after the end of your transmission. You may
press the
key to stop scanning at any time.
WX6
162.500 MHz
Who is covered?
This warranty extends only to the first consumer purchaser, and is
not transferable.
What will GIANT INTERNATIONAL LTD. do?
GIANT INTERNATIONAL LTD., at its option, will at no charge repair,
replace or refund the purchase price of any Products or
Accessories that does not conform to this warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned or
new Products, Accessories or parts.
Products Covered
Length of Coverage
Products and Accessories as
defined above, unless
otherwise provided for below.
One (1) year from the date of
purchase by the first consumer
purchaser of the product unless
otherwise provided for below.
1. Consumer Two-Way Radio
Accessories.
1. Ninety (90) days from the
date of purchase by the first
consumer purchaser of the
product.
2. Products and Accessories
that are Repaired or
Replaced.
2. The balance of the original
warranty or for ninety (90)
days from the date returned
to the consumer, whichever
is longer.
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from state
to state or from one jurisdiction to another.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper
operation, storage, misuse or abuse, accident or neglect, such as
physical damage (cracks, scratches, etc.) to the surface of the
product resulting from misuse; (b) contact with liquid, water, rain,
extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are not the
fault of Motorola or Giant International Ltd., are excluded from
coverage.
Altered Products. Products or Accessories with (a) serial numbers
or date tags that have been removed, altered or obliterated; (b)
broken seals or that show evidence of tampering; (c) mismatched
board serial numbers; or (d) nonconforming or non-Motorola
branded housings, or parts, are excluded from coverage.
Weather Channels and Frequencies
Frequency
What Does this Warranty Cover?
Subject to the exclusions contained to the right, Giant International
Ltd. warrants the Motorola branded consumer two-way radios that
operate via Family Radio Service or General Mobile Radio Service
that it manufactures (“Products”), the Motorola branded or certified
accessories sold for use with these Products that it manufactures
(“Accessories”) to be free from defects in materials and
workmanship under normal consumer usage for the period(s)
outlined below. This limited warranty is a consumer’s exclusive
remedy, and applies as follows to new Motorola branded Products
and Accessories manufactured by Giant International Ltd., and
purchased by consumers in the United States or Canada, which are
accompanied by this written warranty:
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by someone
other than Motorola, Giant International Ltd. or its authorized
service centers, are excluded from coverage.
to save the Weather Alert setting.
Weather
Channel
Consumer Two-Way Radio Products and Accessories purchased in
the United States or Canada.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE, WHETHER
IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES
IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR
ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE
OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR
ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Use of Non-Motorola branded Products and Accessories. Defects
or damage that result from the use of Non-Motorola branded or
certified Products or Accessories or other peripheral equipment
are excluded from coverage.
Communication Services. Defects, damages, or the failure of
Products or Accessories due to any communication service or
signal you may subscribe to or use with the Products or
Accessories is excluded from coverage.
key.
To start Advanced Scanning:
1. Set the Interference Eliminator Code to “zero” or OFF.
6. To stop scanning, briefly press the
3. If the radio repeatedly stops on an undesired transmission, you may
temporarily remove that channel from the scan list by pressing and
holding or
for three seconds. You may remove more than one
channel in this way.
within five
4. The radio will resume scrolling through the channels five seconds
after the end of any received activity.
5. To stop scanning, briefly press the
2. If the radio stops on an undesired transmission, you may immediately
resume the scan by briefly pressing
or
Patent and Copyright Information
Manufactured, distributed or sold by Giant International Ltd., official
licensee for this product. Motorola, the Stylized M Logo, and other
Motorola trademarks and trade dress are owned by Motorola, Inc.
and are used under license from Motorola, Inc. MOTOROLA and the
Stylized M Logo are registered in the US Patent & Trademark Office.
All other product or service names are the property of their
respective owners. ©Motorola, Inc. 2009. All rights reserved.
Please contact customer service at 1-800-638-5119 or e-mail us at
giantintl@callcenter.com for questions/comments, warranty, support
or service related to this product.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
USA Two-Way Radios
Canada Two-Way Radios
1-800-638-5119
giantintl@callcenter.com
1-800-638-5119
giantintl@callcenter.com
For Accessories, please call the telephone number designated
above for the product with which they are used.
You will receive instructions on how to ship the Products or
Accessories at your expense, to a GIANT INTERNATIONAL LTD.
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
MR355

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23
Create Date                     : 2009:01:06 17:00:24Z
Creator Tool                    : QuarkXPress(R) 7.2
Modify Date                     : 2009:01:06 17:01:25-05:00
Metadata Date                   : 2009:01:06 17:01:25-05:00
Producer                        : QuarkXPress(R) 7.2
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments
Format                          : application/pdf
Title                           : Layout 1
Document ID                     : uuid:5edbb81d-3721-fa4a-9c0f-6601619ce20e
Instance ID                     : uuid:7b9d817b-90e6-8e4c-a937-0523e8d78d75
Page Count                      : 2
Creator                         : QuarkXPress(R) 7.2

EXIF Metadata provided by EXIF.tools