Gigaset Communications A58H UPCS Phone User Manual Gigaset A580 IP

Gigaset Communications GmbH UPCS Phone Gigaset A580 IP

User Manual

1The handset at a glanceGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / overview.fm / 24.04.2009Version 8, 03.09.2008The handset at a glance Handset keys 1Display in idle status (example)2Charge status of the batteries (£Page 27)3Display keys (£Page 30)4Message key (£Page 58)Access to Calls and Message lists;Flashes: new message, new call ornew firmware or new provider profile avail-able5End Call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status)6Pound key (#)Keypad lock on/off (press and hold) (£Page 32)Switch between upper/lower case letters and digits for text input (£Page 153)7Internal key Make an internal call (£Page 74)8Microphone 9Flash key Enter flash "F" (press briefly; £Page 127)Fixed line network only:Insert a dialing pause "P" (press and hold)10 Asterisk key (*)Idle status: Ringer melody on/off (press and hold)Fixed line network: switch between dial pulsing/touch tone dialing11 Key 1 (press and hold)Call a network mailbox (if applicable)12 Talk key Answer call, open Last Number Redial list (press briefly in idle status), select connec-tion type and start dialing (press briefly/press and hold after entering the number, £Page 38) 13 Speaker key Switch between earpiece and handsfree mode Lights up: handsfree talking activatedFlashes: incoming call14 Control key (£Page 30)15 Signal strength (£Page 27)2354671413119108112ÐVINT 110.10.08 07:15ÞMenu15
2Overview of display iconsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / overview.fm / 24.04.2009Version 8, 03.09.2008Overview of display icons=eVU Charge status of the batteries (empty to fully charged)=(flashes)Batteries almost emptye V U(flashes)Charging ÒÑiÐ Reception strength iconReception signal strength between the base station and the handset (low to high)| (flashes)No reception signal between the base station and the handset Shortly after activating Eco , the ¼ symbol replaces the reception strength icon in the top left of the handset's idle display. ØKeypad lock activatedÚRinger deactivatedÅIncoming calls on the fixed line network connection (ringer icon)MIncoming call on a VoIP connection ¼Alarm clock setzOpen Last Number Redial list The base station at a glanceBase station key 1Paging key Lights up: LAN connection active (phone is connected to router)Flashes: data transfer to LAN connection Press briefly: Initiate paging (£Page 73), Display the IP address on the handsetPress and hold: Set base station to registration mode (£Page 71)1
3ContentsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPIVZ.fm / 24.04.2009Version 8, 03.09.2008ContentsThe handset at a glance   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Overview of display icons  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2The base station at a glance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2Safety precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   7Gigaset A580 IP – more than just making calls . . . . . . . . . . . . . . .   8VoIP – making calls via the Internet . . . . . . . . . . . . . . . . . . . . . . . .   9Gigaset HDSP – telephony with brilliant sound quality  . . . . . . . .   9First steps   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   10Checking the package contents   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10Setting up the handset for use  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11Installing the base station  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17Connecting the base station  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Making settings for VoIP telephony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21What would you like to do next? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29Operating the handset   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   30Using the Control key   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30Using the Display keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30Using the keys on the keypad  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31Correcting text entry errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31Using the menus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31Activating/deactivating the handset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32Activating/deactivating the keypad lock  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32Using this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33Menu trees  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   34Phone menu   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34Web configurator menu   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37Making calls with VoIP and the fixed line network   . . . . . . . . . .   38Making an external call  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38Ending a call   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41Accepting a call  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41Caller ID  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  42Using speaker mode   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44Muting the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45Deactivating your handset's microphone  . . . . . . . . . . . . . . . . . . . . . . . . . . .  45Making cost-effective calls   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45
4ContentsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPIVZ.fm / 24.04.2009Version 8, 03.09.2008VoIP telephony via Gigaset.net . . . . . . . . . . . . . . . . . . . . . . . . . . .   46Opening the Gigaset.net directory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47Searching for subscribers in the Gigaset.net directory  . . . . . . . . . . . . . . . . .  48Using other functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50Managing your own entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50Calling a Gigaset.net subscriber   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51Network services  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   52Blocking your Caller ID – Anonymous calling  . . . . . . . . . . . . . . . . . . . . . . . .  52Further network services for fixed line networks  . . . . . . . . . . . . . . . . . . . . .  52Further network services for VoIP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53Using lists  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   57using the Last Number Redial list  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  57Opening lists with the Message key  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58Using the directory   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   62Using the network mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   66Configuring the network mailbox for fast access  . . . . . . . . . . . . . . . . . . . . .  66Listening to messages on the network mailbox  . . . . . . . . . . . . . . . . . . . . . .  67ECO DECT: Conserving energy   . . . . . . . . . . . . . . . . . . . . . . . . . . .   69Setting the alarm clock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   70Activating/deactivating the alarm clock   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  70Changing the wake-up time  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  70When the alarm clock rings…  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  70Using multiples handsets   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   71Registering handsets  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71De-registering handsets   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72Locating a handset ("paging") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73Changing a handset's internal number  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73Changing the name of a handset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74Making internal calls  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74Handset settings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   77Changing the date and time  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Changing the display language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Activating/deactivating the screensaver  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78Quickly accessing functions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  79Activating/deactivating auto answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80Changing the handsfree/earpiece volume  . . . . . . . . . . . . . . . . . . . . . . . . . .  80Setting ringers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81Activating/deactivating advisory tones  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82Setting the battery low tone  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  83Restoring the handset default settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  83
5ContentsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPIVZ.fm / 24.04.2009Version 8, 03.09.2008Setting the base station via the handset . . . . . . . . . . . . . . . . . . .   84Protecting against unauthorized access  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  84Restoring the base station to the factory settings   . . . . . . . . . . . . . . . . . . . .  85Activating/deactivating music on hold  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  86Setting default connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  86Entering local and extra area codes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  87Updating the base station firmware  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  87Making VoIP settings on the handset   . . . . . . . . . . . . . . . . . . . . .   89Using the connection wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  89Changing settings without the connection wizard . . . . . . . . . . . . . . . . . . . .  89Setting the phone's IP address in LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  91Activating/deactivating the display of VoIP status messages  . . . . . . . . . . . .  93Checking the base station MAC address  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  93Operating the base station on the PABX  . . . . . . . . . . . . . . . . . . .   94Changing the dialing mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  94Setting recall  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  94Setting access codes (external line prefixes)   . . . . . . . . . . . . . . . . . . . . . . . .  94Setting pauses  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  95Switching temporarily to touch tone dialing (DTMF)  . . . . . . . . . . . . . . . . . .  95Setting the phone with the PC  . . . . . . . . . . . . . . . . . . . . . . . . . . .   96Connecting the PC with the telephone's Web configurator  . . . . . . . . . . . . .  96Logging in, setting the Web configurator language . . . . . . . . . . . . . . . . . . .  98Logging off   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  98Using the Web pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99Menu bar  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99Navigation area  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  100Working area  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  100Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  101Opening Web pages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  101Setting the phone with the Web configurator   . . . . . . . . . . . . . . . . . . . . . .  102Configuring the IP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  103Configuring telephone connections  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  106Optimizing voice quality for VoIP connections  . . . . . . . . . . . . . . . . . . . . . .  115Setting the telephone's default connection  . . . . . . . . . . . . . . . . . . . . . . . .  119Activating the fixed line network connection as an alternate connection .  119Assigning send and receive numbers to handsets  . . . . . . . . . . . . . . . . . . .  120Activating Call Forwarding for VoIP connections   . . . . . . . . . . . . . . . . . . . .  121Entering your own area code, activating/deactivating an automaticarea code for VoIP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  122Activating/deactivating network mailbox, entering numbers   . . . . . . . . . .  125Setting DTMF signaling for VoIP   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  126Defining Flash key functions for VoIP (hook flash)  . . . . . . . . . . . . . . . . . . .  127Configuring call forwarding via VoIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  127Defining local communication ports for VoIP  . . . . . . . . . . . . . . . . . . . . . . .  128Messaging  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  130Configuring info services/activating idle display . . . . . . . . . . . . . . . . . . . . .  133
6ContentsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPIVZ.fm / 24.04.2009Version 8, 03.09.2008Changing internal handset numbers and names  . . . . . . . . . . . . . . . . . . . .  133Transferring handset directories to/from the PC  . . . . . . . . . . . . . . . . . . . . .  134Activating VoIP status message display . . . . . . . . . . . . . . . . . . . . . . . . . . . .  136Starting a firmware update  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  137Activating/deactivating the automatic version check . . . . . . . . . . . . . . . . .  138Copying the date/time from time server . . . . . . . . . . . . . . . . . . . . . . . . . . .  139Querying the phone status  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  140Getting help with your phone   . . . . . . . . . . . . . . . . . . . . . . . . . .   141Questions and answers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  141Using VoIP status codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  145Checking service information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  148Protecting our environment  . . . . . . . . . . . . . . . . . . . . . . . . . . . .   149Our environmental mission statement  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  149Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   150Care  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  150Contact with liquid   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  150Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  150Writing and editing text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  152Industry Canada Certification  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  154FCC / ACTA Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   155Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  157End-user limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  159Gigaset A580 IP – free software  . . . . . . . . . . . . . . . . . . . . . . . . .   163Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   171Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   172Index  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   185Mounting the charging cradle to the wall . . . . . . . . . . . . . . . . .   196Mounting the base station to the wall   . . . . . . . . . . . . . . . . . . .   196
7Safety precautionsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / security.fm / 24.04.2009Version 8, 03.09.2008Safety precautionsWarningBe sure to read this user guide and the safety precautions before using your telephone. Explain their content and the potential hazards associated with using the telephone to your children.Use only the power adapter supplied, as indicated on the underside of the base station or charging cradle.Use only the recommended, rechargeable batteries (£Page 150). Using conventional (non-rechargeable) batteries or other types of batteries could result in significant health risks and personal injury. Do not charge the handset in the charging unit or base station while the headset is connected.Using your telephone may affect nearby medical equipment. Be aware of the technical conditions in your particular environment, e.g. doctor's surgery.Do not hold the rear of the handset to your ear when it is ringing or when the handsfree function is activated. Otherwise you risk serious and permanent dam-age to your hearing.The handset may cause an unpleasant humming noise in hearing aids.Do not install the base station or charging cradle in bathrooms or shower rooms. The handset, base station and charging cradle are not waterproof (£Page 150).Do not use the phone in environments with a potential explosion hazard, e.g. paint shops.If you give your phone to a third party, make sure you also give them the user guide.Remove faulty base stations from use as they could interfere with other wireless services.WarningWhen the keypad lock is active, you cannot call emergency numbers! Please noteNot all of the functions described in this user guide are available in all countries.$ƒ
8Gigaset A580 IP – more than just making callsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Gigaset A580 IP – more than just making callsYou can use your phone to make calls via the fixed line network and also (cost effectively) via the Internet (VoIP) without a PC. – Your phone can do much more: uMake calls with brilliant sound quality using High Definition Sound Performance (HDSP) for either internal calls or calls made via VoIP (£Page 9) – for internal calls or calls via VoIP. uA simple press of a button each time you make a call indicates whether you want to call via the fixed line network or the Internet (£Page 38).uRegister up to six handsets on your base station. With your base station, you can simultaneously conduct two calls via VoIP and one call via the fixed line network. uMultiline: Create up to six VoIP accounts with different VoIP providers. Together with your fixed line number and the Gigaset.net number, your phone can then be reached via up to eight different phone numbers. uAssign each handset its own VoIP number as a send and receive number. If a member of your family is called on their VoIP number, only their handset will ring (£Page 120). uYou can also use the VoIP accounts with different providers for cost control purposes. When dialing, specify the VoIP connection/the VoIP account you want to use for its lower rates (£Page 38).uSetting dialing plans for phone numbers or area codes enables you to auto-mate the selection of the most cost-effective VoIP connection (£Page 123). uUse Gigaset.net for VoIP calls. Connect your phone to the electrical power supply and the Internet and enjoy free phone calls on Gigaset.net – without making any further settings (£Page 46).uConfigure the phone connection for VoIP without a PC. Your phone's con-nection wizard downloads general data about your VoIP provider from the Internet and guides you through entering your personal data (VoIP/SIP account). This makes it easy for you to start using VoIP (£Page 21). uIf necessary, make any further VoIP settings on a PC. The phone features a Web interface (Web configurator) that can be accessed via your PC's Web browser (£Page 96). uMake sure your phone is always up-to-date. Keep yourself informed about firmware updates on the Internet and download them onto your phone (£Page 87). uReduce the transmission power by activating Eco mode / Eco mode+ (£Page 69).Have fun using your new phone! Your Gigaset A580 IP has a protected operating system that offers increased security against viruses from the Internet.
9VoIP – making calls via the InternetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008VoIP – making calls via the InternetWith VoIP (Voice over Internet Protocol), your calls are not made via a fixed con-nection as with the telephone network, but rather they are transmitted via the Internet in the form of data packets. You can take advantage of all the benefits of VoIP with your phone:uYou can make cost-effective calls in high voice quality with callers on the Internet, the fixed line network or the cell phone network. uVoIP providers will give you personal numbers, with which you can be reached from the Internet, the fixed line network and any cell phone net-work. To use VoIP, you need: uA broadband Internet connection (e.g. DSL) with flat rate (recommended) or volume-based price. uInternet access, i.e. you need a router that will connect your phone to the Internet. You can find a list of recommended routers on the Internet at: www.gigaset.com/customercareFrom here, go to the FAQ page and select "Gigaset A580 IP". Search for "Router", for example. uAccess the services of a VoIP provider. You can open up to six accounts with different VoIP providers. Gigaset HDSP – telephony with brilliant sound qualityYour Gigaset IP phone supports the Broadband codec G.722. With your base station and the corresponding hand-set, you can make calls via VoIP with brilliant sound quality (High Definition Sound Performance). If you register further broadband-capable handsets (e.g. Gigaset S67H, S68H or SL37H) with your base station, internal calls between these handsets will also be conducted via broadband. Prerequisites for broadband connections to your base station are: uFor internal calls: Both handsets are broadband-capable, i.e. both support the codec G.722. uFor external calls via VoIP: – You make the call from a broadband-capable handset.– You have selected codec G.722 for outgoing calls, £Page 115. – Your VoIP provider supports broadband connections.– The recipient's phone supports codec G.722 and accepts broadband con-nections.Please noteThe VoIP service Gigaset.net (£Page 46) supports broadband connections.
10First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008First stepsChecking the package contents§§1§§ one Gigaset A580 IP base station §§2§§ one power adapter for connecting the base station to the electrical power supply§§3§§ one phone cord for connecting the base station to the fixed line network§§4§§ one Ethernet (LAN) cable for connecting the base station to the router (LAN/Internet)§§5§§ one Gigaset A58H handset§§6§§ two batteries for the handset (uncharged)§§7§§ one battery compartment cover for the handset§§8§§ one handset charging cradle§§9§§ one power adapter for connecting the charging cradle to the electrical power supply§§10§§ one quick guide and a CD containing this user guide12345678910
11First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Setting up the handset for useThe display is protected by a plastic film. Please remove the protective film!Inserting the batteries and closing the battery coverUse only the recommended, rechargeable batteries (£Page 150). Using con-ventional (non-rechargeable) batteries or other types of batteries could result in significant health risks and personal injury. For example, the outer casing of the batteries could be destroyed or the batteries could explode. The phone could also malfunction or be damaged as a result of using batteries that are not of the recommended type.Firmware updatesThis user guide describes the basic functions from firmware version 179. Whenever there are new or improved functions for your Gigaset A580 IP, base station firmware updates will be made available for you to download to your telephone (£Page 87). If this results in operational changes to your phone, a new version of this user guide or the necessary amendments will be published on the Internet at www.gigaset.com Select "Gigaset A580 IP" in the product field to open the relevant product page where you will find a link to the user guide. For information on finding the current firmware version of your base station, £Page 140 (using the Web configurator) or £Page 148 (during an external call). Warning
12First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008¤Insert the batteries with the polarity in the correct direction.The polarity is indi-cated in/on the battery compartment.¤First insert the battery cover at the top 1.¤Then press the cover 2 until it clicks into place.¤To open the battery cover, for instance to replace the batteries, remove the belt clip (if attached). Insert a coin into the cavity on the casing, then pull the battery cover in an upward direction. 12
13First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Connecting the charging cradleThe charging cradle is designed to be operated in enclosed, dry areas at tem-peratures ranging from +41°F to +113°F. If you have any questions and problems £Page 141.For information on attaching the charging cradle to the wall, £Page 195.¤Plug the electrical adapter into the plug socket 2.¤Connect the empty plug from the power adapter 1.To disconnect the plug from the charging cradle, press the release button 1 and dis-connect the plug 2. 1212Please noteuOnly place the handset in the charging cradle for which it is intended.uIf the handset has turned itself off because the batteries are empty and is then placed in the charging cradle, it will turn itself on automatically.
14First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Initial charging and discharging of the batteries¤Then remove the handset from the charging cradle and do not replace it until the batteries are fully discharged.The charge status is displayed in the idle display. = e V U (empty to full)  = flashes, the batteries are almost empty.After the first battery charge and discharge, you may place your handset in the charging cradle after every call. Setting the date and timeThe date and time must be set to have the correct time for incoming calls and to use the alarm clock.Setting up manually:¤Place the handset in the charging cradle and wait until the batteries are fully charged (approx. 10 hours). Battery charging is indicated in the top right of the display by the flashing battery icon e.  10 hWarninguAlways repeat the charging and discharging procedure if you remove the batteries from the handset and reinsert them.uThe batteries may warm up during charging. This is not dangerous.uAfter a while, the charge capacity of the batteries will decrease for technical reasons.Please noteThe address of a time server on the Internet is stored on your telephone. The date and time are taken from this time server, provided that the base station is connected to the Internet and synchronization with the time server is acti-vated (£Page 139). Manual settings are overwritten in this case. ¤Press the key below §Menu§ on the display screen to open the main menu. ÞMenu
15First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008¤Press the Control key down repeatedly ...… until the Settings menu item appears. ¤Press the key below §OK§ on the display screen to confirm your selection. mSettingsÇUOKThe Date/Time menu item appears on the display.¤Press the key below §OK§ on the display screen to open the input field. Date/TimeÇUOK¤The active line is marked [...].Enter month, day and year as an 8-digit number (MMDDYYYY) via the keypad, e.g. QQ2QQNfor 10/10/2008.To correct an entry, press up or down on the Control key to toggle between fields.Enter Date:10.10.2008]ÇUOK
16First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Registering the handset to the base station Your handset is registered to the base station by default. For information on registering additional handsets with the base station and make free internal calls, £Page 71. ¤Press the key below §OK§ on the display screen to confirm your selection. ÇUOK¤Enter the hours and minutes as 4-digit numbers via the keypad, e.g. QM5for 07:15 am.If necessary, use the Control key to toggle between fields.¤Press the key below §am/pm§ on the display screen to choose between am and pm.¤Press the key below §OK§ on the display screen to confirm your selection. Enter time:[07:15] pmam/pm UOK¤Press and hold the End Call key a to return to the idle status. The display shows Saved. You will hear a confirmation tone.Saved
17First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Installing the base stationThe base station is designed for use in closed, dry rooms with a temperature range of +41°F to +113°F. ¤Set up the base station at a central location on a flat, non-slip surface in your house or apartment.The phone's feet do not usually leave any marks on surfaces. However, due to the multitude of different varnishes and polishes used on today's furnishings, the occurrence of marks on the surfaces cannot be completely ruled out.For information on mounting the base station on the wall, £Page 195.Please noteConsider the range of the base station.This is up to 328 yards in unobstructed outdoor areas and up to 54 yards inside buildings. The range is reduced when eco mode is activated (£Page 69).WarninguNever expose the telephone to any of the following: heat sources, direct sunlight or other electrical appliances.uProtect your Gigaset from moisture, dust, corrosive liquids and fumes.
18First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Connecting the base stationTo make calls with your phone via the fixed line network and via VoIP, you must connect the base station to the fixed line network and the Internet, £Figure 1. Follow the steps in the order given below (£Figure 1): §§1§§ Connect the phone cord and power lead to the base station.§§2§§ Connect the base station to the fixed line network and the electrical power supply.§§3§§ To connect the base station to the Internet, first connect the base station to the router(connection via router and modem or via router with integrated modem).§§4§§ Connect the PC and router (optional) – for advanced configuration of the base station (£Page 96). Figure 1  Connecting the phone to the fixed line network and the Internet§§4§§§§1§§§§2§§§§3§§
19First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.20081. Connect the phone cord and power lead to the base station§§1§§ Insert the phone cord into the lower connection socket at the rear of the base station. §§2§§ Insert the power lead of the power adapter into the upper connection socket at the rear of the base station. §§3§§ Push both cables into the appropriate cable channels. 2. Connect the base station to the fixed line network and the electrical power supply §§1§§ Insert the phone cord into the fixed line network connection socket.§§2§§ Then insert the power adapter into the electrical socket.213§§2§§ §§1§§
20First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008You can now use your phone to make calls via the fixed line network and can be reached on your fixed line number. 3. Connect the base station with the router (Internet)For Internet access you need a router connected to the Internet via a modem (this may be integrated in the router).§§1§§ Connect an Ethernet cable plug into the LAN port at the side of the base sta-tion.§§2§§ Then insert the other end of the Ethernet cable plug into a LAN port on the router.As soon as the cable connecting the phone and router is plugged in and the router is activated, the key lights up on the front of the base station (Paging key). You are now ready to establish VoIP connections within Gigaset.net (£Page 46).WarninguKeep the power adapter plugged in at all times for operation, as the phone does not work without an electrical power connection.uUse only the power adapter and phone cord supplied. Pin connections on telephone cords can vary (pin connections £Page 152).§§2§§§§1§§
21First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Making settings for VoIP telephonyBefore you can use the Internet (VoIP) to phone any other numbers on the Internet, the fixed line network or the cellular phone network, you need the services of a VoIP provider who supports the VoIP SIP standard.Prerequisite: You have registered with such a VoIP provider (e.g. via your PC) and set up at least one VoIP account. To use VoIP, you need to enter the access data for your VoIP account. You will receive all the necessary data from your VoIP provider. This will include:uYour user name (if requested by the VoIP provider) is the user identification (Caller ID) for your account, which is often identical to your phone numberuYour authentication name or login IDuThe (login) password registered with the VoIP provideruGeneral settings for your VoIP provider (server addresses, etc.)Your phone connection wizard can help you make these entries. Starting the connection wizardPrerequisite: The base station is connected to the electrical power supply and a router. Your router is connected to the Internet (£Page 20). Please noteYour phone is preconfigured for dynamic assignment of the IP address. In order for your router to "recognize" the phone, dynamic IP address assignment must also be activated on the router, i.e. the router's DHCP server must be acti-vated. If the DHCP server cannot or should not be activated, you must first assign a fixed IP address to the phone. For further information, see Page 91.As soon as the handset battery is sufficiently charged, the Message keyf on the handset will flash (approx. 20 minutes after you have put the handset in the charging cradle). ¤Press the Message key f.
22First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008You will see the following display. ¤Press the key below §Yes§ on the display screen. You will be prompted to enter your phone's system PIN.Start VoIP connection  wizard?No YesNew firmware available appears in the display.New/improved firmware is available for your phone on the Internet. First per-form an automatic update of the firmware (£Page 88). Once the update has been completed (after approx. 3 minutes) the handset's idle display appears again and the Message key f flashes. If you press f, the display shown in the picture above appears and you can start the connection wizard. Please noteTo protect your phone and its system settings from unauthorized access, please define a 4-digit number code (system PIN) known only to yourself. This code must be entered before you can register/de-register handsets or alter your phone's VoIP or LAN settings.The default system PIN is 0000 (4 x zero). For further information, see Page 84. The active line is marked [----].¤Enter your phone's current system PIN using the keypad. ¤Press the key below §OK§ on the display screen. The connection wizard is launched. System PIN:[ _ _ _ _ ]ÇOKPlease noteuYou can also call up the connection wizard at any time via the menu (£Page 89).uThe connection wizard will also start automatically if you try to establish a connection via the Internet before you have made the necessary settings. Prerequisite: You have not activated the fixed line network connection as a replacement connection (£Page 119):
23First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Downloading VoIP provider dataThe connection wizard establishes a connection with the Gigaset configuration server on the Internet. Various profiles with general access data for different VoIP providers can be downloaded here. After a brief period you will see the following display:¤Press the key below §Yes§ on the display screen. Select VoIP provider?No YesA list of countries is loaded.The first country in the list appears in the display. ¤Press up or down on the Control key repeatedly ...... until the country in which you are using the phone appears on the display. ¤Press the key below §OK§ on the display screen to confirm your selection. Select country GermanyÇVOKÇUOK
24First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008The general access data for your VoIP provider is downloaded.Entering user data for your first VoIP accountYou will now be prompted to enter your personal access data for your VoIP accounts. The following are provider-dependent: u Username, Authentication Name, Authentication PasswordOr:uAuthentication Name, Authentication PasswordA list of VoIP providers whose data you can download is loaded.The first VoIP provider in the list appears in the display. ¤Press up or down on the Control key repeatedly q ...... until your VoIP provider appears on the display. ¤Press the key below §OK§ on the display screen to confirm your selection. Select provider Provider 1ÇVOKProvider xÇUOKPlease note If the data for your VoIP provider is not available for downloading, press the ” display key twice. You can then carry out the following steps with the connec-tion wizard. You must then make the settings needed for the VoIP provider using the Web configurator (£Page 107). Your VoIP provider will supply you with this data.
25First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Please note When entering case sensitive access data: uTo switch between upper and lower case and digits, press the # key (several times if necessary). You can see briefly in the display whether upper case, lower case or digits is selected.uCharacters entered incorrectly can be deleted using the left Display key below X. The character to the left of the cursor will be deleted. uYou can navigate within the input field using the Control key p (press up/down).If your VoIP provider does not require a user name, skip this step.¤Using the keypad, enter the user name that you received from your VoIP pro-vider. ¤Press the key below §OK§ on the display screen. ¤Using the keypad, enter the authentica-tion name that you received from your VoIP provider. ¤Press the key below §OK§ on the display screen. ¤Use the keypad to enter your password. ¤Press the key below §OK§ on the display screen.  Username:ÛTOKAuthentication Name:ÛTOKAuthentication Password:ÛTOK
26First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Completing the VoIP settingsAfter the entries have been completed, the handset reverts to idle status.¤Test whether your VoIP data is complete and has been stored in the phone correctly. Calling via VoIP:Enter a number using the handset keypad and press and hold the Talk key c. If a VoIP connection cannot be established, a corresponding message is shown in the display. You can now use your phone to make calls via the fixed line network and the Internet! Callers can reach you on your fixed line number and your VoIP number.Please noteuTo ensure that you can always be reached via the Internet, the router must be permanently connected to the Internet.uIf you have started the connection wizard via the menu, once the entries are completed, press and hold the End Call key a to return the handset to idle status.uIf you try to make a call via a VoIP connection that is not configured cor-rectly, the following VoIP status message will appear in the display: VoIP config. error: xxx (xxx = VoIP status code). The various status codes and their  respective meanings are listed on Page 145. Please noteYou can enter five additional VoIP accounts (VoIP phone numbers) via the Web configurator later (£Page 106). Together with your fixed line network number and the Gigaset.net number, your phone can then be reached via up to eight different phone numbers. You can assign the phone numbers to the individual handsets that are registered with the base station as send and receive numbers (£Page 120). ÐVINT 1 ÞMenu
27First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Icons on the idle displayThe following is displayed:uthe internal number, e.g. INT 1.uthe quality of the reception signal between base station and handset (signal strength):–poor to good:ÒÑiЖno reception:  | flashesubattery charge status:–= e V U(empty to full) –=flashes: batteries almost empty–e V Uflashes: charging procedure No connection to the Internet/VoIP serverIf one of the following messages is displayed instead of the internal name after the connection wizard is closed, errors have occurred:uServer not accessible! uSIP registration failed Below you will find possible causes and measures you can take. Server not accessible! The phone has no connection to the Internet.¤Check the cable connections between the base station and the router (the LED on the base station must light up) and the connection between the router and the Internet connection.¤Verify that the phone is connected to the LAN. – It may not have been possible to dynamically assign an IP address to the phoneor – You have assigned a static IP address to the phone that has either already been assigned to another LAN subscriber or does not belong to the router's address block.¤Press the Paging key on the base station. The IP address appears on the handset display.¤Press the Talk key on the handset to end paging call. ¤Start the Web configurator with the IP address.¤If no connection can be established, change the settings on the router (activate DHCP server) or the phone's IP address.
28First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008SIP registration failed uYour personal data for registering with the VoIP provider may have been entered incompletely or incorrectly. ¤Check your entries for Username, Authentication Name and Authentication Password. Particularly check your use of upper and lower case. To do this, open the following menu on your handset:§Menu§ ¢Settings ¢Base ¢Telephony ¢VoIP (enter system PIN) (£Page 90)uThe server address for the VoIP server has not yet been entered, or has been entered incorrectly.¤Start the Web configurator.¤Open the following Web page: Settings ¢Telephony ¢Connections. ¤Click the Edit button next to the first VoIP connection. ¤Edit the server address where necessary.Please noteIf port forwarding is activated on your router for the ports (£Page 128) that have been registered as the SIP and RTP ports, we recommend to deactivate DHCP and assign the phone a static IP address (otherwise you may not be able to hear the other party during VoIP calls):uAssign an IP address via the handset menu:§Menu§ £Settings £Base £Local NetworkOruAssign an IP address via the Web configurator:¤Open the following Web page: Settings £IP Configuration. ¤Select IP address type.Please note that the IP address and subnet mask depend on the router's address block. You must also enter the default gateway and DNS server. The IP address for the router is generally entered here.
29First stepsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008What would you like to do next?Now you have successfully started your phone, you will probably want to adapt it to your personal requirements. Use the following guide to quickly locate the most important subjects.If you are unfamiliar with menu-driven devices such as other Gigaset tele-phones first read the section "Operating the handset" £Page 30.If you have any questions about using your phone, please read the troubleshooting tips in the section "Questions and answers" (£Page 141), or contact our Customer Care team (£Page 141).Information on ... ... is located here.Making calls via VoIP or the fixed line network Page 38Setting the ringer melody and volume Page 81Setting the handset volume Page 80Entering local area code/extra codes Page 87Eco mode Page 69Operating the telephone on a PABX Page 94Registering existing handsets to a base station Page 71Transferring directory entries from existing Gigaset handsets to the new handset(s)Page 65Entering additional VoIP accounts Page 106ggggggggg
30Operating the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Operating the handsetUsing the Control keyIn the following description, the side of the Control key you need to press for each operation is indicated accordingly, e.g. tfor "press up on the Control key". The Control key has a number of different functions:With the handset in idle status (without a screensaver)s  Press briefly to open the handset directory.Press and hold: open Gigaset.net directory.tCall up the menu to set the ringer volume (£Page 81).In the main menu, in submenus and listst/ s  Scroll up/down line by line.In input fieldsUse the Control key to move the cursor to the left t or right s. During an external calls  Press briefly to open the handset directory.tAdjust the loudspeaker volume for earpiece and handsfree mode. Using the Display keysThe function of the display keys changes depending on the particular operating situation. Example:Important Display keys:Open a context-dependent menu.Confirm selection.WDelete key: deletes one character at a time from right to left.Go back one menu level or cancel operation.Open the Last Number Redial list.ÇUOK Current Display key functions are shown in the bottom display line.Display keysMenuOKÇÞ
31Operating the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Using the keys on the keypadc/ Q/ *, etc. Press the matching key on the handset. ~Enter digits or letters. Correcting text entry errorsYou can correct incorrect characters in the text by navigating to the incorrect entry using the Control key. You can then:uPress X to delete the character to the left of the cursor uInsert characters to the left of the cursoruOverwrite the (flashing) character when entering the time and date, etc.Using the menusYour telephone's functions are accessed using a menu that has a number of lev-els. Main menu (first menu level) ¤When the handset is in idle status, press §Menu§to open the main menu.The main menu functions are shown on the display as a list with name and icon. To access a function, i.e. to open the corresponding submenu (next menu level):¤Navigate to the function using the Control key q. Press the Display key §OK§. Submenus The functions in the submenus are displayed as lists. To access a function:¤Scroll to the function with the Control key q and press §OK§. Or:¤Enter the corresponding digit combination (£Page 34).Briefly press the End Call key a once to return to the previous menu level/cancel the operation.
32Operating the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Reverting to idle statusYou can revert to idle status from anywhere in the menu as follows:¤Press and hold the End Call key a.Or:¤Do not press any key: after 2 minutes the display will automatically revert to idle status.Any settings you have not confirmed by pressing §OK§ will be discarded.An example of the display in idle status is shown on £Page 26. Activating/deactivating the handsetaWith the phone in idle status, press and hold the End Call key (con-firmation tone) to switch off the handset. Press and hold the End Call key again to switch the handset on.Activating/deactivating the keypad lockThe keypad lock prevents any inadvertent use of the phone.#Press and hold the Pound key (#) to activate or deactivate the key-pad lock. You will hear the confirmation tone. When the keypad lock is activated you will see the Ø icon on the display and a message when you press a key.The keypad lock is deactivated automatically if someone calls you. It is reacti-vated when the call is finished.
33Operating the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / starting.fm / 24.04.2009Version 8, 03.09.2008Using this guideThe operating steps are shown in abbreviated form.Example:§Menu§ ¢Settings ¢Handset ¢Auto Answer (‰=on)This illustration represents:¤Press the Display key below §Menu§ to open the main menu. ÞMenuSettingsÇUOK¤Press down on the Control key s repeatedly until the Settings menu item appears on the dis-play. ¤Press the Display key below §OK§ to confirm your selection. HandsetÇUOK¤Press down on the Control key s repeatedly until the Handset menu item appears on the display. ¤Press the Display key below §OK§ to confirm your selection. Auto AnswerÇUOK‰The Auto Answer menu item appears on the display.¤Press the key below §OK§ to activate/deactivate the function. If the function is activated, this is indicated by ‰.
34Menu treesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / menuetree.fm / 24.04.2009Version 8, 03.09.2008Menu treesPhone menuOpen the main menu on your phone by clicking on the right Display key §Menu§ when the handset is in idle status. There are two ways to select a function:Using number combinations ("shortcut") ¤Enter the number combination that is in front of the function in the menu tree. Example: §Menu§ M32 for "Set handset language".Scrolling through the menus ¤Scroll to the function with the Control key q (press up or down) and press §OK§. 3êSelect Services3-1 VoIP 3-1-6 For All Calls 3-1-6-1 Call Diversion £Page 533-1-6-3 Call Waiting £Page 543-3 All calls anonymous £Page 523-4 Next call anonymous £Page 524  ì Alarm Clock4-1 Activation £Page 704-2 Wake up time £Page 705þ Voice Mail5-2 Set Key 1 Net AM: Fixed Line £Page 66Net AM: IP1::(dependent on the number of configured VoIP phone numbers and receive numbers on the handset)Net AM: IP6
35Menu treesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / menuetree.fm / 24.04.2009Version 8, 03.09.20087 m Settings7-1 Date/Time £Page 147-2 Audio Settings 7-2-1 Call Volume 7-2-1-1 Earpiece Volume £Page 807-2-1-2 Handsfree Volume7-2-2 Ringer Volume £Page 817-2-3 Ringer Melody 7-2-3-1 External Calls £Page 817-2-3-2 Internal Calls7-2-3-3 Alarm Clock7-2-4 Advisory Tones £Page 827-2-5 Battery Low 7-2-5-1 Off £Page 837-2-5-2 On7-2-5-3 During Call7-3 Handset 7-3-1 Display 7-3-1-1 Screensaver £Page 787-3-2 Language £Page 777-3-3 Auto Answer £Page 807-3-4 Register Handset £Page 717-3-5 Reset Handset £Page 83
36Menu treesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / menuetree.fm / 24.04.2009Version 8, 03.09.20087-4 Base 7-4-1 Calls List Type 7-4-1-1 Missed Calls £Page 597-4-1-2 All Calls7-4-2 Music on hold £Page 867-4-3 System PIN  £Page 847-4-4 Base Reset  £Page 857-4-5 Additional Features 7-4-5-2 Access Code £Page 947-4-5-4 Eco mode £Page 697-4-6 Local Network 7-4-6-1 Dynamic IP address £Page 917-4-6-2 IP Address7-4-6-3 Subnet Mask7-4-6-4 DNS Server7-4-6-5 Default Gateway7-4-7 Telephony 7-4-7-1 Default Line Type £Page 867-4-7-2 Connection Wizard £Page 897-4-7-4 Area Code £Page 877-4-7-5 Extra Codes £Page 877-4-7-6 Fixed line £Page 947-4-7-7 VoIP £Page 897-4-8 Firmware Update £Page 87
37Menu treesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / menuetree.fm / 24.04.2009Version 8, 03.09.2008Web configurator menuHome £Page 99Settings IP Configuration £Page 103Telephony Connections £Page 106Audio £Page 115Number Assignment £Page 120Call Forwarding £Page 121Dialing Plans £Page 123Network Mailbox £Page 125Advanced Settings £Page 126Messaging Messenger £Page 130E-Mail £Page 132Services £Page 133Handsets £Page 133 and Page 134Miscellaneous £Page 137 to Page 139Status Device £Page 140
38Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Making calls with VoIP and the fixed line networkMaking an external call External calls are calls made via the public telephone network (fixed line network) or via the Internet (VoIP). You decide which connection type you want to use for a specific call when you dial the number. You have the following options:uSelect the connection type with the Talk key c (briefly press/press and hold c), £Page 38.uSelect the connection type via the display keys by assigning VoIP or the fixed line network to your left Display key, £Page 39uSelect a special connection via your line suffix, £Page 38Use the Talk key to select the type of connection and make the callBy briefly pressing or pressing and holding the Talk key c, you can determine the type of connection for the call you want to make (fixed line network or VoIP). Prerequisite: You enter the number without a line suffix (£Page 38) and have not defined any dialing plans for this number (£Page 123).~c Enter number (without suffix) and briefly press/press and hold the Talk key. A default connection is established on your phone (fixed line network or VoIP £Page 86/Page 119). ¤Briefly press the Talk key c to make a call via this default connection. ¤Press and hold the Talk key c to make the call via the other connection type. Please noteuYou can conduct three separate external calls via your base station (using different handsets): two calls via VoIP and one via the fixed line network. uYou can define dialing plans for certain numbers or area codes by determin-ing the connection and therefore the billing method to be used (cost con-trol £Page 123) when these numbers are dialed.uDialing with the Directory (£Page 62), Shortcut keys (£Page 64) or Last Number Redial list (£Page 57) saves repeated keying of phone numbers. You can modify or add to these numbers on a call-to-call basis.uIf you use VoIP to make a call to the fixed line network, you may also have to dial your local area code for local calls (depending on the VoIP provider). You can avoid having to dial your own area code by entering it into the con-figuration ( £Page 87, Page 122) and activating the option Predial area code for local calls through VoIP (£Page 122). uDepending on the exchange, you may not have to dial your own area code when making local calls via the fixed line network.
39Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008If you have assigned a number of VoIP numbers to your phone, you can define which VoIP number (VoIP account) is used for external calls from each specific handset (handset send number, £Page 120).Use the Display key to select the type of connection and make the callPrerequisite: §Phone§ or §IP§ is assigned to your handset's left Display key (£Page 79).§Phone§ / §IP§  Press the Display key to define the connection type.~/sEnter number or select from the directory.c/ dPress the Talk or Handsfree key. The number is dialed via the selected line type. Exception:If you have activated the option "Automatic Fallback to Fixed Line" (Web configu-rator, £Page 119) and the attempt to establish a connection via VoIP fails, an attempt is made automatically to establish the connection via the fixed line network. Selecting and dialing a connection via your line suffixYou can configure up to six VoIP numbers on your phone in addition to the fixed line network number and the Gigaset.net number. A (line) suffix is assigned to each number (line) of your phone:uThe fixed line network number has the suffix #0 uVoIP numbers have the suffixes #1 to #6 (£Page 107) uAnd the Gigaset.net number has the suffix #9When dialing, you can use this line suffix to specify the connection via which you would like to call or be charged.Please noteuIf you are using a GAP compatible handset other than the Gigaset handsets A58H, S67H, S68H, SL37H, S45 and C45, every call will be made via the standard connection, even if you press and hold the Talk key. uIf you have activated the option Automatic Fallback to Fixed Line with the Web configurator (£Page 119):If the attempt to establish a connection fails, an attempt is made automat-ically to establish the connection via the fixed line network. Please noteIf you have pressed the Display key §IP§ before dialing and ...uDialed the number with suffix #1 to #6, your call will be made via the VoIP account assigned to the suffix. The number will not be dialed if the suffix is invalid (e.g. no VoIP connection assigned). uDialed the number without a suffix or with the suffix #0, your call will be made via the handset's VoIP send number. Do not enter a suffix if you have pressed the Display key §Phone§ prior to dialing. Otherwise the suffix will be dialed together with the number via the fixed line network. This may cause errors!
40Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008~  Enter the number of the party you wish to call.~  Add the suffix of the connection (your phone number) from which the call is to be made and charged to. cPress the Talk key. The connection is always made via the line with the assigned suffix, regardless of whether you press the Talk key c briefly or press and hold.Entering an IP address (provider-dependent)You can also dial an IP address instead of a phone number using VoIP.¤Press the Asterisk key * to separate the sections of the IP address (e.g. 149*246*122*28).¤If necessary press the Pound #key to attach the SIP port number of the person you are calling to the IP address (e.g. 149*246*122*28#5060).You cannot dial IP addresses using a line suffix.If your VoIP provider does not support the choice of IP addresses, each part of the address will be interpreted as a normal phone number. Canceling the dialing operationYou can cancel the dialing operation with the End Call key a.Dialing emergency numbers – defining dialing plansYou can use the Web configurator to block certain numbers or to define which of your numbers (fixed line network, VoIP) should be used to call specific num-bers (Dialing Plans, £Page 123).If you enter a number that has a defined dialing plan, the call will be made via the line defined in the dialing plan – regardless of whether the Talk key is pressed briefly or pressed and held. Any automatic area code will not be pre-fixed to the number. ExampleIf you enter the number 1234567890#1 and press the Talk key c, the number 1234567890 will be dialed via the first VoIP connection in the config-uration. Please noteuIf you specify a suffix for which no VoIP connection is configured in your base station, the VoIP status code 0x33 is displayed. The number will not be dialed.uIf you have activated the option Automatic Fallback to Fixed Line with the Web configurator (£Page 119):If the attempt to establish a connection fails, an attempt is made automat-ically to establish the connection via the fixed line network.
41Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Emergency numbersDialing plans for emergency numbers (e.g. the local emergency service number) are preset for certain countries. Emergency calls are then always made via the fixed line network. You cannot delete or deactivate these dialing plans. However, you can change the connection through which each emergency number should be called (e.g. if the phone is not connected to the fixed line network). You must make sure that the VoIP provider for the selected connection supports emergency calls. If your phone does not have default dialing plans for emergency calls, define the rules yourself (£Page 123). Assign them to a connection that you know supports emergency calls. Calls to emergency numbers are always supported by fixed line networks. Ending a callaPress the End Call key.Accepting a callThe handset indicates an incoming call in three ways: by ringing, by a display on the screen and by the flashing Handsfree key d. You can accept the call by:¤Pressing the Talk key c.¤Pressing the Handsfree key d. If the handset is in the charging cradle and the Auto Answer function is activated (£Page 80), the handset will take a call automatically when you lift it out of the cradle. To deactivate the ringer, press the §Menu§ Display key and select Silent. You can accept the call as long as it is displayed on the screen.Please noteuIf no rules are defined for emergency numbers and you have programmed an automatic local area code (£Page 122), the code will be prefixed to emergency numbers as soon as they are dialed via a VoIP connection.uEmergency numbers cannot be dialed if the keypad lock is activated. Before dialing, press and hold the Pound key #, to release the keypad lock. Please noteOnly calls to receive numbers assigned to your handset will be signaled (£Page 120). The following conditions apply in particular:uCalls made to a number that is not assigned to a handset as a receive number will be signaled on all handsets. uIf you have not assigned receive numbers to any of the handsets, calls to all connections will be signaled on all handsets.uCalls to your IP address are always signaled on all handsets.
42Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Caller IDWhen you receive a call from the Internet, the caller's number or the name they have specified is displayed on the screen. When you receive a call from the fixed line network, the caller's number and/or name is displayed on the screen if you have requested Caller ID (CID) from your network provider. If the phone number is identified and the caller's number is saved in the direc-tory, the name is displayed from the directory. Call display You can use the display to determine whether the call is for your fixed line net-work number or one of your VoIP numbers. 1 Ringer icon2 Number or name of the caller if available3 Receive number: indicates which of your phone numbers the caller has dialed. Assign the name when you are configuring the phone with the Web configurator (£Page 108/Page 114). For calls from Gigaset.net, For Gigaset.net is displayed. Withholding calling line display The number or name of the caller is not displayed in the following cases:uThe caller has activated the "anonymous calling" function. uA caller from the fixed line network has not requested Caller ID from the fixed line network provider. Please noteYou can reject VoIP calls by pressing the End Call key a. The caller receives an appropriate message (provider-dependent). Calls to your fixed line number  Calls to one of your VoIP numbers Å1234567890For Fixed LineMenu12345678901234567890For IP1Menu23123
43Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008The following is displayed in place of the number:uWith a call to one of your VoIP phone numbers, the display is provider-dependent (examples): uFor a call to your fixed line network number: – If no number is transmitted:– If the caller has withheld Caller ID: – If the caller has not arranged Caller ID: Screen display with CID (fixed line network)Prerequisite: Call is made from a fixed line network connection to your fixed line network number. If you have CID, then the name (town/city) that is registered with your network provider for the caller's number will also be displayed. If the caller's number is stored in your directory then the directory entry will be shown. The display shows:uExternal Call, if no number is transmitted.uPrivate, if the caller has suppressed Caller IDuNot available, if the caller has not arranged Caller ID. PrivateanonymousFor IP1Menu MExternal CallFor IP1Menuor ÅExternal CallFor Fixed LineMenu ÅPrivateFor Fixed LineMenu ÅNot availableFor Fixed LineMenu
44Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008VoIP: Displaying the called party's phone number (COLP) Prerequisites: uYour VoIP provider supports COLP (Connected Line Identification Presenta-tion). You may have to ask your provider to activate COLP (contact your VoIP provider for more information). uThe called party has not activated COLR (Connected Line Identification Restriction).For outgoing VoIP calls, the phone number of the connection on which the call is received is displayed on the handset. The displayed number may differ from the number you have dialed. Examples:uThe called party has activated call forwarding. uThe call is answered by another connection within a PABX system. If there is an entry in the directory for this phone number, the corresponding name is displayed. Using speaker modeIn speaker mode, instead of holding the handset to your ear you can put it down, for example on the table in front of you. This allows others to participate in the call.Activating/deactivating speaker modeActivating while dialing ~d Enter number and briefly press/press and hold the Speaker key to select the connection type (£Page 38).¤Inform your caller before you use the speaker function so that they know someone else may be listening. Switching between earpiece and speaker mode¤Press the Speaker key d to activate or deactivate the speaker during a call and when listening to the answering machine.If you wish to place the handset in the charging cradle during a call:¤Press and hold the Speaker key d while placing the handset in the charg-ing cradle. ¤If the Speaker key d does not light up, press the key again.For instructions on adjusting the handset volume, see £Page 80. Please noteuThe number of the connection you have reached (or the assigned name) will also be displayed instead of the called number during toggling, confer-ence calls and consultation calls. uWhen the phone number is copied to the directory (§Menu§ £Copy to phone-book) and the Last Number Redial list, the dialed number (not the displayed number) is copied.
45Making calls with VoIP and the fixed line networkGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Muting the handsetYou can deactivate the microphone in your handset during an external call. The other party will hear music on hold, if activated (£Page 86). kPress the Display key to mute the handset./ a  Press the Display or the End Call key, to reactivate the microphone. Deactivating your handset's microphoneYou can deactivate your handset's microphone during an external call (includ-ing during a conference or when toggling). The other party can no longer hear you, but you can still hear them.§Mute§ Press the Display key to mute the handset.Your handset's microphone is deactivated. Im"Microphone is turned off." appears in the display. §On§ Press the Display key to switch the microphone back on. Making cost-effective calls You can use your phone's cost control function for calls to fixed line or mobile phone networks. Open accounts with various VoIP providers who offer favora-ble rates for calls to other networks. In the phone configuration, define the most cost-effective VoIP connections (account), e.g. for specific regional, national and cellular network prefixes, to be used when calls are made (Dialing Plans, £Page 123). Or define the VoIP connection to be used when dialing the number ( £dialing with line suffix, Page 38). If you are using your fixed line network to make a call, choose a network pro-vider that offers particularly favorable rates (call-by-call). ÇPlease note Under the following circumstances, the microphone is automatically reacti-vated:uIf, during an external call (you have deactivated the microphone), you establish a second connection, either by accepting a waiting call or by suc-cessfully connecting to an external/internal consultation call, the micro-phone is activated. If you go back to the first party, the microphone remains activated. (If you reject a waiting call or are unable to connect to a consultation call, the microphone remains deactivated.)uIf you have deactivated the microphone during call swapping, it is reacti-vated for both connections as soon as you swap to the other party. uIf you have deactivated the microphone during a conference call, the micro-phone is reactivated when you end the conference call by pressing §Menu§ ¢End Conference (call swap).
46VoIP telephony via Gigaset.netGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Displaying the call durationThe duration of each call appears in the display for calls made via a fixed line network and VoIPuDuring the conversation,uUntil about three seconds after the call has ended if you do not replace the handset in the charging cradle.VoIP telephony via Gigaset.netYou can use Gigaset.net to make free phone calls via the Internet directly to other Gigaset.net users, without having to set up an account with a VoIP pro-vider or make any further settings. You simply have to connect your phone to the power supply and the Internet connection and, if necessary, enter yourself in the Gigaset.net online directory under a name of your choice (£Page 47/Page 50).Gigaset.net is a VoIP service provided by Gigaset Communications GmbH* to which all users of a Gigaset VoIP device can subscribe. You can call other subscribers to Gigaset.net free of charge, i.e. there are no telephone charges other than the costs for your Internet connection. Connec-tions to/from other networks are not possible. Every Gigaset VoIP device is assigned a Gigaset.net phone number by default (£Page 148). All registered subscribers are included in the Gigaset.net directory, which you are able to access. An echo service is available on the phone number 12341#9 (English), 12344#9 (French) or 12346#9 (Spanish) for you to check your VoIP connec-tion. After an announcement, the echo service sends back the voice data you have received immediately in the form of an echo. Exclusion of liabilityGigaset.net is a voluntary service provided by Gigaset Communications GmbH with no liability for or guarantee of network availability. This service can be ter-minated at any time with a notice period of three months.Please noteThe actual duration of the call can vary from that shown by a few seconds.* Gigaset Communications GmbH is a licensee of the Siemens trademark.Please noteIf you do not use your Gigaset.net connection for six weeks, it is automatically deactivated. You cannot be reached for calls from Gigaset.net. The connection is reactivated:uAs soon as you start a search in the Gigaset.net directory or uMake a call via Gigaset.net (dial a number with #9 at the end) or uActivate the connection via the Web configurator (£Page 114).
47VoIP telephony via Gigaset.netGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Opening the Gigaset.net directoryYour handset is in idle status. sPress and hold. Or: ¤Open the directory with the s button. ¤Select Gigaset.net from the directory and press the Talk key c. A connection to the Gigaset.net directory is established.If a connection cannot be made to the Gigaset.net directory, an error message will be sent and the handset will go into idle status.After opening the Gigaset.net directory for the first timeWhen opening the Gigaset.net directory for the first time you can use the Gigaset.net wizard to create an entry in the Gigaset.net directory for your phone.You will see the following display: ¤Press the Display key §Yes§ to start the wizard.Please noteuThe Gigaset.net directory entry is transferred to a handset when it is regis-tered with the base station, if the handset can send and receive directory entries.uCalls to the Gigaset.net directory are always free of charge. uYou can also open the Gigaset.net directory by dialing 1188#9 (phone number of the Gigaset.net directory) and pressing the Talk key c. Start Gigaset.net  wizard?No YesPlease noteIf you press §No§ the wizard will be canceled. You can then create the entry later via the Gigaset.net directory (£Page 50).
48VoIP telephony via Gigaset.netGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008When the wizard has been started the following display will appear (example): ¤Using the keypad, enter the name that you would like to be listed under in the Gigaset.net directory. The name may contain a maximum of 25 charac-ters.¤Press the key below §OK§. If there is already an entry under this name, you will receive a message to this effect and you will be asked to enter a name again: Please choose another name.If an entry in the Gigaset.net directory is successful, the message Name added to Gigaset.net is displayed. You have not been able to enter a nameIf the attempt to create the entry fails you can create it via the Gigaset.net directory (£Page 50).Searching for subscribers in the Gigaset.net directoryOnce the connection has been established, you will be asked to enter a name that you want to search for. Nickname:Enter the name or part of a name (maximum 25 characters).§Menu§ Press the Display key. Start search Select and press §OK§.If the search has been successful, a Hit list of all the names that begin with the specified character string is displayed. Example:1. 5/25: Entry number/number of hits2. Name of the entry, the name is displayed in full, if necessary over several linesYou can scroll through the Hit list with q. Your nickname:1happyuserÛTOK5/25Sand, Anna MagdalenaView UMenu12
49VoIP telephony via Gigaset.netGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008If it has not been possible to find a matching entry, a corresponding message is displayed. You have the following options:¤Press the Display key §New§ to start a new search.Or¤Press the Display key §Change§ to change the search criteria. The previously entered name is copied and can be edited. If there are too many matching entries in the Gigaset.net directory, the mes-sage Too many entries found is displayed instead of a Hit list. ¤Press the Display key §Refine§ to start a refined search. The previously entered name is copied and can be edited/expanded. Calling participantsq  Select the subscriber from the Hit list.c  Press the Talk key. Viewing the subscriber's numberq  Select the subscriber from the Hit list.§View§ Press the Display key. The display shows the Gigaset.net number and the subscriber's name. Depending on the length of the information, the name may cross several lines. Example:1234567#9Sand, Anna MagdalenaÇUOKPlease noteuConnections to Gigaset.net are always established via the Internet regard-less of which default connection is set on your phone. Pressing and holding c or pressing it briefly have no effect. uYou can open the Gigaset.net directory and establish connections, even if you have not entered yourself in the Gigaset.net directory.
50VoIP telephony via Gigaset.netGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Using other functions Prerequisite: The Hit list is displayed. q(select entry) ¢§Menu§ The following functions can be selected with q:Copy to DirectoryCopy the entry to the handset directory. The number and name (abbreviated if necessary, maximum 16 characters) are copied to the directory. ¤Edit and save entry where appropriate (£Page 63). The Hit list is displayed again. Show numberDisplay the number of the entry. ¤Press the Display key §OK§, to return to the Hit list. New searchStart a search with a new name (£Page 48).Refine searchStart detailed search. The previously entered Nickname can be edited/expanded and the search can be restarted (£Page 48).Your name in Gigaset.net £ "Managing your own entry", Page 50.Managing your own entryYou have the following options:uEdit the name of your entry in the Gigaset.net directory uDelete your entry from the Gigaset.net directory Viewing own entry ¤You are connected to the Gigaset.net directory:Select §Menu§ ¢ Your name in Gigaset.net and press §OK§.Or:¤You are in a Gigaset.net Hit list: Select §Menu§ ¢ Own information and press §OK§.Your Gigaset.net number and, where applicable, your currently entered name are displayed. Please noteIf you select a Gigaset.net number from the local directory, the connection is automatically established via Gigaset.net (Internet).
51VoIP telephony via Gigaset.netGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / telephony.fm / 24.04.2009Version 8, 03.09.2008Entering/editing a name§Edit§ Press the Display key.~  Edit name or enter new name (maximum 25 characters) and press §OK§. You can delete the name with X. If there is no existing entry with this name in the Gigaset.net directory, the name is saved. A message to this effect is displayed. The handset switches to idle status. If there is an existing entry with this name, or the entered name contains invalid characters, you will be requested to enter a different name. Deleting your own entry from the Gigaset.net directory Prerequisite: You are connected to the Gigaset.net directory:§Menu§ ¢ Your name in Gigaset.net / Own information Select and press §OK§.§Edit§ Press the Display key.X  Delete name and press §OK§. Your entry is deleted from the directory. You are no longer "visible" to other Gigaset.net subscribers. However, you can still be reached via your Gigaset.net number. Calling a Gigaset.net subscriberYou can call a Gigaset.net subscriber directly via the Gigaset.net directory (see above) or via their Gigaset.net number:~/s  Enter the Gigaset.net number (including the #9) or select from the handset directory.cPress the Talk key. Every number ending with #9 is dialed via Gigaset.net. Please noteFor instructions on displaying your Gigaset.net number, see Page 148.
52Network servicesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / netservices_SAG.fm / 24.04.2009Version 8, 03.09.2008Network servicesNetwork services are functions made available by your fixed line network or VoIP provider. Blocking your Caller ID – Anonymous callingPhone number identification can be blocked. Your phone number will not be displayed when making outgoing calls. You are calling anonymously. Prerequisites:uFor anonymous calls via your fixed line network connection you need to have requested the relevant service (feature) from your fixed line network provider. uAnonymous calls are only possible via VoIP connections through providers that support the "anonymous calling" function. You may have to ask your VoIP provider to activate this function. Activating/deactivating "anonymous calling" for all callsWithholding caller ID can be activated/deactivated permanently for all of your phone's connections (fixed line network and VoIP). When this function is activated, the phone number will be withheld both for fixed line network calls and for calls via a VoIP connection. Withholding caller ID is activated for all registered handsets. §Menu§ ¢Select Services All calls anonymousSelect and press §OK§ (‰=on). Activating/deactivating "anonymous calling" for the next callYou can activate/deactivate withholding caller ID for the next call.§Menu§ ¢Select Services ¢Next call anonymousYes / No  Select and press §OK§. ~ If necessary, enter the phone number with line suffix. §Send§  Press the Display key. The phone number is dialed. If you have not specified a line suffix, the number will be dialed via the default con-nection.Further network services for fixed line networksThe following network services can only be used for making calls via the fixed line network. You will need to request them from your fixed line network pro-vider. ¤Contact your network provider for further assistance.
53Network servicesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / netservices_SAG.fm / 24.04.2009Version 8, 03.09.2008Functions during a callInitiating ringback You have dialed a number via the fixed line network and can hear the busy tone.§Menu§ ¢RingbackaPress the End Call key.As soon as the dialed number becomes available, the phone rings.¤Press the Talk key c, to establish a connection to that number. Consultation callsDuring a call: §Menu§ ¢External CallSelect and press §OK§.~Enter a number or copy it from the directory and press §OK§.The number will be dialed via the fixed line connection.uConference call:– Talk to both participants: §Menu§ ¢Conference Call.– End call with both participants: press the End Call key a.Further network services for VoIPYou can use the following network services to make calls via the VoIP connec-tion. Settings for all callsGeneral call forwarding Prerequisite: The VoIP provider supports call forwarding.§Menu§ ¢Select Services ¢VoIP ¢For All Calls ¢Call DiversionThe display shows a list of configured and activated VoIP phone numbers and the Gigaset.net number of your telephone. Numbers for which call forwarding is activated are marked with ‰. qSelect the phone number for which you want to activate or change call forwarding and press §OK§. All Calls / No Answer / When BusySelect and press §OK§ (‰= on).On Select and press §OK§.Please noteAfter a few seconds, the number selected for a consultation call is saved in the Last Number Redial list.
54Network servicesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / netservices_SAG.fm / 24.04.2009Version 8, 03.09.2008~If necessary, enter the number to which the call is to be forwarded.You can specify a fixed line network, VoIP or mobile number for for-warding calls from a VoIP number. You must specify another Gigaset.net number for call forwarding from your Gigaset.net number. §OK§  Press the Display key. a Press and hold (idle status).Call forwarding is activated for the selected phone number (receive number). This does not result in calls for the other VoIP numbers or your fixed network numbers being forwarded.  Deactivating call forwardingqSelect the VoIP phone number for which you want to deactivate call forwarding and press §OK§. All Calls / No Answer / When BusySelect and press §OK§ (‰= on).Off Select and press §OK§.a Press and hold (idle status). Call forwarding is deactivated.Activating/deactivating call waitingPrerequisite: Your phone will permit two parallel VoIP connections (see Allow 1 VoIP call only, £Page 116). If call waiting is activated, a caller on one of your VoIP connections will hear the ringer if you are already on a call using this VoIP connection. This call is announced sound and visually on your handset screen.Calls on the fixed line connection are not signaled as call waiting. They are sig-naled on other registered handsets to which the fixed line number has been assigned as a receive number. If no other handset is available, the caller will hear the busy tone. Accepting/rejecting a waiting call, £Page 56.§Menu§ ¢Select Services ¢VoIP ¢For All Calls ¢Call WaitingOn / Off Select and press §OK§.a Press and hold (idle status). Please noteForwarding VoIP phone numbers can incur additional costs. Please consult your VoIP provider. Please noteThe setting applies to all VoIP phone numbers. It does not affect the procedure for call waiting on the fixed line network.
55Network servicesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / netservices_SAG.fm / 24.04.2009Version 8, 03.09.2008Functions during a callPrerequisite: Your phone will permit two parallel VoIP connections (see Allow 1 VoIP call only, £Page 116). Consultation callsDuring an external call: §Menu§ ¢External CallSelect and press §OK§.~ Enter the number (if necessary the suffix) or copy it from the direc-tory.cPress the Talk key. The number is always dialed via VoIP. If no suffix is entered, it is selected via the VoIP send number.If the participant does not answer: ¤Press the Display key §End§, to return to the waiting call. If the participant answers, you have the following options:uToggling:¤Use q to toggle between the participants. ¤End call with active participant: §Menu§ ¢End Active Call.Press the End Call key a, to end the current call. The participant who was previously waiting will automatically call you back. uConference call:¤Talk to both participants: §Menu§ ¢Conference Call.¤End conference call (toggle): §Menu§ ¢End Conference.¤End call with both participants: press the End Call key a.Please noteAfter a few seconds, the number selected for a consultation call is saved in the Last Number Redial list.
56Network servicesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / netservices_SAG.fm / 24.04.2009Version 8, 03.09.2008uCall forwarding (provider-dependent):You can connect the two external participants. Prerequisites: – You are toggling calls and you phoned the currently active participant yourself.– You have activated call forwarding via the Web configurator (£Page 127)Depending on the setting in the Web configurator (£Page 127): ¤Press the End Call key a. Or:¤Press key S.If call forwarding was successful, a message will appear to this effect. The handset will then switch to idle.If call forwarding was not successful, the party that was previously waiting will call you back. Accepting a waiting callPrerequisite: Call waiting is activated (£Page 54). §Menu§ ¢Accept Call WaitingYou have the option of toggling or holding a conference call.Rejecting a waiting callMenu§ ¢Reject Call WaitingThe caller hears the busy tone. Please noteuIf the first call was an internal call, the internal connection is ended.uAn internal, waiting call is shown on the display. You can neither accept the internal call nor reject it.
57Using listsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Using listsThe options are: uLast Number Redial list uCalls list uNetwork mailbox using the Last Number Redial listThe Last Number Redial list contains the ten numbers last dialed with the handset (maximum 32 numbers). If one of the numbers is in the directory, the corresponding name is displayed.Dialing from the Last Number Redial listcPress the key briefly.sSelect entry. cBriefly press/press and hold the Talk key. The number is dialed using the selected connection type (£Page 38).Managing entries in the Last Number Redial listcPress the key briefly.sSelect entry.§Menu§ Open menu.The following functions can be selected with q: Use Number Save or modify a saved number and then dial with c or save as a new entry; to do so, press §Menu§ ¢Copy to phonebook ¢§OK§after the number appears on the display.Copy to Directory Copy an entry to the directory (£Page 65).Delete Entry Delete selected entry. Delete List Delete complete list.
58Using listsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Opening lists with the Message keyYou can use the Message key f to open the following list selection:uCalls listuNetwork mailbox, £Page 67A separate list is displayed for each network mailbox. Prerequisite: Its number is saved in the base station, it is switched on (£Page 125) and the corresponding VoIP/fixed line network number is assigned to the handset as a receive number. An advisory tone sounds as soon as a new message arrives in a list. The f key flashes (it goes off when the key is pressed). The message You have new mes-sages appears in the display in idle status.List selectionThe lists displayed after pressing the message key f depend on whether there are any new messages.f key does not flash (no new messages): All lists are displayed. Select a list with q. To open, press §OK§.f key flashes (new messages received): All the lists that contain new messages are displayed as well as the network mailbox lists, whose connection is assigned to the handset as a receive number (Net AM  Fixed Line, Net AM  IP1,...).Network Mailbox listsIf you select a Network Mailbox list and press §OK§ you will be connected directly to the network mailbox. For information on network mailboxes, £Page 67.Calls listThe Calls list contains the last 20 numbers, depending on the type of list setuAll calls–answered calls– unanswered callsuMissed calls– unanswered calls Multiple calls from the same number will be stored once in the list of missed calls (the latest call). The number of calls from this number is shown in brackets after the entry. Multiple calls from the same number are stored several times in the list of answered calls.
59Using listsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008The Calls list is displayed as follows:1 Number of new entries2 Number of old, read entriesSetting the Calls list type§Menu§ ¢Settings ¢Base ¢Calls List TypeMissed Calls / All CallsSelect and press §OK§ (‰=on).a Press and hold (idle status). The Calls list entries are retained when you change the list type.Open the Calls listf ¢Calls List 01+02 Select and press §OK§.qSelect entry.The last incoming call is displayed in the Calls list.Please noteuOnly calls to the receive numbers assigned to your handset are stored in the Calls list (£Page 120). If no receive numbers are assigned, all calls will be stored in the Calls list for all handsets.uMissed calls are not stored in the Calls list if they were taken on another phone registered with the same VoIP access data. Calls List:02+03ÇUOK12
60Using listsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008List entryExample of a list entry:uStatus of entryNew Call: new missed call.Old Call: entry already read.Call recv.: call answered (in list type All Calls).uEntry number01/02 means e.g. first new entry of a total of two new entries.uNumber or name of the caller (the number is always stored in the list with the area code)uCall date and time (if set, £Page 77).Managing entries in the Calls list Prerequisite: You have opened the Calls list and selected an entry.§Menu§ Press the Display key.The following functions can be selected with q:Delete EntryDelete selected entry.Copy to DirectoryCopy a displayed number to the directory.Show NameVoIP:If a URI was received and stored for a VoIP call, this will be shown. The URI is dialed if you press the Talk key c. The URI is not entered on the Last Number Redial list. Fixed line network:  £ "Displaying CID information", Page 61.Show ConnectionDisplay the name of the connection (fixed line network/VoIP account), for which the call was received. Delete List Delete complete list.New Call 01/02123456789010.10.08 12:14ÇUMenu
61Using listsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Displaying CID informationIf you have CID, you can display the name and town/city that is registered with your network provider for this number.You have selected a list entry.§Menu§ ¢Show NameIf the name and town/city are not shown, it means that the caller has not requested Caller ID or that Caller ID has been withheld. Press §OK§ to return to the list.Selecting from the Calls listf ¢Calls List 01+02 qSelect entry.cBriefly press/press and hold the Talk key. The number is dialed using the selected connection type (£Page 38).Please noteStore your own area code on your phone ( £Page 87, Page 122) so that the area code is automatically withheld during local calls on the fixed line net-work.
62Using the directoryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Using the directoryYou can save up to 150 entries in your directory (number dependent on the number of individual entries).You can create a personalized directory for your own individual handset. However, you can send the list or individual entries to other handsets £Page 65.In the directory you can save numbers and corresponding names.¤With the handset in idle status, open the directory by pressing the s key. Entry lengthNumber:  maximum 32 digits Name:  maximum 16 characters Saving the first number in the directorysOpen the directory.The display shows Dir. empty  New entry?. §OK§ Press the Display key. ~  Enter the number and press §OK§.~  Enter the name and press §OK§.Please noteFor quick access to a number from the directory (shortcut), you can assign the number to a key (£Page 64).Please noteSome VoIP providers do not support local calls for calls to the fixed line net-work. In this case, always enter the fixed line number with the area code in your directory. Alternately, you can also use the Web configurator to define an area code, which is automatically prefixed to all numbers that are dialed via VoIP without an area code (£Page 122).Please note that (depending on the fixed line network provider), when local calls are made via the fixed line network the number cannot be dialed with an area code.
63Using the directoryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Storing a number in the directorys ¢§Menu§ ¢New Entry~  Enter the number and press §OK§.~  Enter the name and press §OK§.Order of directory entries The directory entries are usually sorted in alphabetical order. Spaces and digits take first priority. The sort order is as follows:§§1§§ Space§§2§§ Digits (0–9)§§3§§ Letters (alphabetical)§§4§§ Other charactersTo work round the alphabetical order of the entries, insert a space or a digit in front of the name. These entries will then move to the beginning of the direc-tory. Names that you have prefixed with an asterisk will move to the end of the directory.Selecting a directory entrys  Open the directory. You have the following options:uUse s to scroll through the entries until the required name is selected. uEnter the first character of the name and scroll to the entry using s if required. Dialing with the directorys ¢s(Select entry). c  Briefly press/press and hold the Talk key. The number is dialed using the selected connection type (£Page 38). Please noteuFor information on entering IP addresses, £Page 40.uTo dial a number using a certain line connection each time, you can add the relevant line suffix to the number in question (Page 38). uYou can use the Web configurator to save the directory to a file on your PC, where it can be edited and then sent back to the handset (£Page 134). Or you can transfer Outlook contacts from the PC to the handset's directory.Please noteYou can only dial IP addresses via VoIP.
64Using the directoryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Managing directory entriess ¢s(Select entry). Editing entries §Menu§ ¢Edit Entry~  Edit the number if required, and press §OK§.~  Edit the name if required, and press §OK§.Using other functions §Menu§ Press the Display key.The following functions can be selected with q:Use Number Save or modify a saved number and then dial with c or save as a new entry; to do so, press §Menu§ ¢Copy to phonebook ¢§OK§after the number appears on the display.Delete Entry Delete selected entry.Send Entry Send a single entry to a handset (£Page 65).Delete List Delete all directory entries.Send List Send complete list to a handset (£Page 65).Shortcut Assign the phone number of the current entry to a number key as a shortcut (Shortcut key). Using Shortcut keysYou can assign phone numbers from the directory to number keys on your handset ( £Shortcut, Page 64). Number keys to which phone numbers are assigned are known as Shortcut keys. ¤Press and hold the required Shortcut key.If there is a valid line suffix at the end of the number in the directory (e.g.: #1), the number will be dialed via the line belonging to the suffix (£Page 107). The number is dialed via the default connection. Exception: A dialing plan has been defined for the number (£Page 123).
65Using the directoryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / directories_charges.fm / 24.04.2009Version 8, 03.09.2008Transferring the directory to another handsetPrerequisites:uThe sending and receiving handsets must both be registered to the same base station. uThe other handset and the base station can send and receive directory entries.s ¢s(Select entry) ¢§Menu§ (Open menu) ¢Send Entry / Send List sSelect the internal number of the receiving handset and press §OK§. Successful transmission is confirmed by the message Entry copied. You can transfer several individual entries one after the other by responding §OK§ to the Next entry? prompt.Copying a displayed number to the directoryYou can copy numbers displayed in a list, e.g. the Calls list or Last Number Redial list, to the directory.If you have CID, the first 16 characters of the transmitted name are copied to the Enter Name line. A number is displayed: §Menu§ ¢Copy to phonebook ¤Complete the entry, £Page 63. Copying a number from the directory There are many operating situations in which you can open the directory, e.g. to copy a number. Your handset need not be in idle status.sOpen the directory.qSelect entry.§Menu§ Press the Display key.Select function with q.Please noteuEntries with identical numbers are not overwritten on the receiving handset. uThe transfer is canceled if the phone rings or if the memory of the receiving handset is full.
66Using the network mailboxGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Using the network mailboxSome fixed network providers and VoIP providers offer answer machines on the network – these are known as network mailboxes. Each network mailbox accepts incoming calls made via the corresponding line (fixed line network or corresponding VoIP phone number). To record all calls, you should therefore set up network mailboxes for both the fixed line network and for each of your VoIP connections. úYou can activate/deactivate the network mailboxes for your VoIP connections using the Web configurator. To do this, you only need the network mailbox phone number. For information activating/deactivating network mailboxes via the Web config-urator and to change their assigned numbers, £Page 125.úYou need to have requested the network mailbox for your fixed line network connection from your fixed line network provider. You can store the phone number for the fixed line network mailbox in the Web configurator on the base station (£Page 125). You cannot activate/deactivate the network mailbox for the fixed line network connection via the Web configurator. For activating/deactivating the network mailbox for the fixed line network connection please refer to the fixed line net-work provider's information.Configuring the network mailbox for fast access With fast access you can dial a network mailbox directly. Assigning key 1 of the handset, changing assignmentsThe setting for fast access is handset-specific. You can assign a different mail-box to key  on each registered handset. No mailbox is preconfigured for fast access in the default settings. Prerequisites: uAt least one receive number is assigned to the handset.uThe corresponding network mailbox has been entered and activated for at least one of the receive numbers on the handset. Fast access has not yet been set on the handset: Press and hold key . Please noteuFor many VoIP network mailboxes, the phone number is automatically saved on the base station when the general VoIP provider data is down-loaded. uIf you have registered a Gigaset C47H, S67H or S68H handset to your base station, you can also enter and activate the network mailbox via this hand-set. For further information on this, read the user guide for the Gigaset C470 IP or S675 IP on the Internet.
67Using the network mailboxGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Or: §Menu§ ¢Voice Mail ¢Set Key 1Select and press §OK§.s  Select network mailbox and press §OK§ (=on). The selection includes the network mailboxes that belong to a VoIP/fixed line network connection and whose phone number is assigned to the handset as a receive number. Net AM: xxx where xxx is replaced by the standard name in the connection (IP1 to IP6, Fixed Line).If a number is already saved to the base station for the selected network mail-box, fast access is activated. aPress and hold (idle status). If no number has been saved for the network mailbox the message Not possible! is displayed. You then have to first enter the mailbox number using the Web configurator (£Page 125). Calling the network mailbox and listening to messagesPress and hold. If you have set a network mailbox for fast access you will be connected directly to this network mailbox (external call). dIf necessary, press the Handsfree key.You will hear the answer machine announcement.Listening to messages on the network mailboxUnder the Message key f you will find a list for each network mailbox that fulfills the following requirements: uThe corresponding connection is assigned to the handset as a receive number. uThe network mailbox phone number is saved on the base station.uThe network mailbox is on (activated £Page 125).You can use the list to call the network mailbox directly and listen to the mes-sages. ‰Please noteYou can only assign fast access to one mailbox. However, you can also call the network mailbox assigned to a handset's receive numbers directly via the Message key (£Page 67).
68Using the network mailboxGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008When you press the Message key f, the following is displayed (example):1 Network mailbox name. Net AM  IP1, ..., Net AM  IP6 or Net AM  Fixed Line isdisplayed. IP1 ... are the standard names of the corresponding connections. The default names are always displayed regardless of which connection name you specified when configur-ing via the Web configurator. 2 The number of new messages is displayed (2 = two new messages). If there are no new messages, (0) is displayed. The number of messages stored in the network mail-box is not displayed.Displaying new messages on the handset If a new message is present on one of the network mailboxes that is assigned to the handset via its receive number, the Message key f flashes.Calling the network mailbox and checking messagesfPress the Message key.Net AM  Fixed Line / Net AM  IP1 / ... / Net AM  IP6 Select the network mailbox and press §OK§. You are connected directly to the network mailbox (external call) and hear its announcement. Messages can generally be played back using your handset keypad (digit codes). Listen to the announcement. úYou must define how the digit codes for VoIP should be converted to DTMF signals and transmitted. The Web configurator is used to make this setting £Page 126. Ask your VoIP provider which type of DTMF transmission it supports.Net AM : IP1[2]ÇUOK12Please noteuThe network mailbox is automatically called via the corresponding connec-tion. An area code predefined for your phone is not prefixed. uAfter the call, the number of new messages on the handset returns to (0), even if not all or no new messages have been listened to.
69ECO DECT: Conserving energyGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008ECO DECT: Conserving energyThe base station of your phone is an ECO DECT base station, this means that:uThe base station and the charging cradle consume less power because they are equipped with a power-saving electrical power adaptor. uThe reduction of the handset's transmission power is dependent on the handset's proximity to the base station.uThe base station can also be switched to the Eco mode. Eco mode reduces the transmission power and the power consumption of the base station further. Eco mode means:80% reduction of the transmission power in standby mode and when making calls. Eco mode is available when the handset(s) and the base station are close together, e.g. when the phone is being used in an office. The setting can be made on the handset.Activating/deactivating Eco mode§Menu§ ¢Settings ¢Base ¢Additional FeaturesEco modeSelect and press §OK§ (‰=on).Reception displayScreen icon Reception strength:ÒÑiÐ| (flashes)– poor to good– no receptionPlease noteuActivating Eco mode reduces the range of the base station.
70Setting the alarm clockGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Setting the alarm clockPrerequisite: The date and time have already been set (£Page 14).Activating/deactivating the alarm clock§Menu§ ¢Alarm ClockActivation Select and press §OK§ (‰=on). After you activate the alarm clock, the menu for setting the wake-up time opens automatically.~Enter the wake-up time in 4 digits (hours and minutes) and press §OK§.aPress and hold (idle status). If the alarm clock is set, the wake-up time appears with the ¼icon in the display instead of the date.Changing the wake-up time§Menu§ ¢Alarm Clock  ¢Wake up time ~Enter the 4-digit wake-up time (in hours and minutes) and then press §OK§.aPress and hold (idle status). When the alarm clock rings…A wake-up call with the selected ringer melody is signaled on the handset (£Page 81). The wake-up call lasts for a maximum of 5 minutes. If no key is pressed, the wake-up call is repeated twice at five minute intervals and then turned off for 24 hours. During a call, the wake-up call is only signaled by a short tone. Alarm repeated after 5 minutes (snooze mode) §Snooze§ Press the Display key or any other key (apart from the left Display key).If you press §Snooze§ three times, the alarm clock switches off for 24 hours.Turning off the alarm clock for 24 hours§Off§ Press the Display key.
71Using multiples handsetsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Using multiples handsetsRegistering handsetsYou can register up to six handsets to your base station.When you register a new Gigaset handset, the base station transfers the Gigaset.net entry for the Gigaset.net directory (£Page 48) to its local direc-tory to enable you to use the Gigaset.net directory on your new handset.Prerequisite: The handset can send and receive directory entries. See the handset’s user guide for further information.Successful registration is acknowledged with the message Data Transfer x  entries rec for this reason.Registering another Gigaset A58H handset on the Gigaset A580 IP Before you can use your handset, you must register it to the base station.You must initiate handset registration on the handset and on the base station.The handset will return to idle status if registration was successful. The hand-set's internal name is shown in the display, e.g. INT 1. If it does not appear, repeat the procedure. Registration can take up to one minute. ¤On the handset: Select §Menu§ ¢Settings ¢Handset  ¢Register Handset and press §OK§. ¤Enter the system PIN of the base station (the default is 0000) and press §OK§. Handset is registering flashes on the display.¤Within the next 60 seconds press and hold (for approx. 3 seconds) the Registration/Paging key (£Page 2) on the base station. The handset is assigned the lowest available internal number (1-6). The inter-nal number appears in the display after registration, e.g. INT 2. This means that the internal number 2 has been assigned to the handset. Please noteuIf several handsets are registered on your base station, you can simultane-ously make two calls via the Internet and one via the fixed line network. Up to two additional internal connections are also possible. uSelecting the connection via the Talk key (£Page 38) is not supported on GAP handsets. This means that if you enter a number without a line suffix and without defining a dialing plan for the phone number it will be dialed via the default connection (£Page 86). uAfter registration, all the phone numbers for the phone will be assigned to the handset as receive numbers. It will use the fixed line network number and the first VoIP number in the configuration as send numbers. For information on changing the assignments, £Page 120.
72Using multiples handsetsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Registering other handsets on the Gigaset A580 IPYou can register other Gigaset handsets and handsets for other devices with GAP functionality as follows. ¤Start the registration procedure on the handset in accordance with the handset's operating instructions.¤Press and hold (for approx. 3 seconds) the Registration/Paging key (£Page 2) on the base station. De-registering handsetsYou can de-register any registered handset from any registered Gigaset A58H handset.ÑÑ Open list of internal participants.The handset which you are using is marked with <.qSelect the handset to be de-registered.§Menu§ Press the Display key.De-register HandsetSelect and press §OK§. ~Enter the system PIN of the base station (the default is 0000) and press §OK§. De-register handset?Press §OK§, to confirm the prompt.aPress and hold (idle status). The handset is de-registered immediately, even if it is not in idle status.Please noteIf six handsets are already registered to the base station, there are two options:uThe handset with the internal number 6 is in idle status: the handset you wish to register is assigned the number 6. The handset that was previously number 6 is de-registered.uThe handset with the internal number 6 is being used: the handset you wish to register cannot be registered.
73Using multiples handsetsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Locating a handset ("paging")You can locate your handset using the base station. ¤Briefly press the Registration/Paging key on the base station (£Page 2).All handsets will ring simultaneously ("paging"), even if ringer melodies are switched off.The current (local) IP address for the base station appears in the handset displays. Example:Ending paging¤Briefly press the Registration/Paging key on the base station (£Page 2). Or¤Press the Talk key c or End Call key a on any handset.Or¤Do not press any key on the base station or handset: After approx. 30 seconds, the paging call will end automatically.Changing a handset's internal numberA handset is automatically assigned the lowest free number when it is regis-tered. In the list of internal participants, the handsets are sorted according to their internal number. You can change the internal number of all registered handsets (1–6). The numbers 1-6 can only be assigned once each.kOpen the list of registered handsets.§Menu§ Press the Display key.Edit Handset NumberSelect and press §OK§. qSelect handset.~Enter the new internal number (1–6). The handset's old number is overwritten.q~ If necessary, select another handset and change its number.Please noteuAn incoming external call will not interrupt the paging process.uIf there is an internal connection between the two handsets, paging is not possible.ÅPaging192.168.0.100
74Using multiples handsetsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008After all the changes are completed:§OK§ Press the Display key to save the input. a Press and hold (idle status). You will hear the error tone if an internal number has been assigned twice.¤Repeat the procedure with a free number.Changing the name of a handsetThe names "INT 1", "INT 2", etc. are assigned automatically on registration. You can change these names. The changed name is displayed in every handset's list.kOpen the list of registered handsets.qSelect handset.§Menu§ Press the Display key.Change Handset NameSelect and press §OK§. The handset's current name is displayed. X Delete the old name if necessary.~Enter new name (maximum 10 characters) and press §OK§.a Press and hold (idle status). Making internal callsInternal calls to other handsets registered on the same base station are free.Calling a specific handsetkOpen the list of registered handsets. s Select handset.cPress the Talk key.Or:kOpen the list of registered handsets.~Enter the internal handset number (1–6). Calling all handsets ("group call")k Open the list of registered handsets.*Press the Asterisk key. All handsets are called. Or:kOpen the list of registered handsets.Call All Select. cPress the Talk key. All handsets are called.Please noteIf you delete the current handset name with Xand then press §OK§ without entering a new name, the handset will automatically be assigned the default name "INT x" (x= internal number).
75Using multiples handsetsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008Ending a calla  Press the End Call key.Transferring a call to another handset You can forward (connect) an external call, made via the fixed line network or VoIP, to another handset.Prerequisite: You are conducting an external call.kOpen the list of registered handsets.sSelect handset or Call all. §OK§ /cPress the Display key or the Talk key.Or: kOpen the list of registered handsets. ~Enter the internal number of the handset. The external participant hears music on hold if activated (£Page 86).When the internal participant answers:¤If necessary announce the external call. a  Press the End Call key.The external call is transferred to the other handset. If the internal participant does not respond or is busy:§Menu§ ¢Back Select and press §OK§.You are reconnected with the external participant. You can also press the End Call key a when forwarding a call before the inter-nal participant picks up the call. Then, if the internal participant does not answer or the line is busy, the call will automatically return to you (the display will show Recall).Initiating internal consultation call, conference callYou are talking to an external participant (via fixed line network or VoIP) and can call an internal participant at the same time to hold a consultation call. Prerequisite: You are conducting an external call.kOpen the list of registered handsets. sSelect handset or Call all. §OK§ /cPress the Display key or the Talk key.Or: kOpen the list of registered handsets. Please noteuYou can reject an internal call by pressing the End Call key a. Other hand-sets will continue to signal an internal "group call". uIf the called handset is not answered, the busy tone sounds after approx. 3minutes.
76Using multiples handsetsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.04.2009Version 8, 03.09.2008~Enter the internal number of the handset. The external participant hears music on hold if activated (£Page 86).When an internal participant answers you can speak to them.You have the following options: Ending a consultation call§Menu§ ¢Back Select and press §OK§.You are reconnected with the external participant.Initiating a conference call§Menu§ ¢Conference Call Select and press §OK§.You are in a three-way conference call with the external participant and the internal participant. During an internal consultation/conference callIf the internal participant who has been called ends the call (press End Call key a), you will be reconnected with the external participant. If you press the End Call key a,the external call will be transferred to the internal participant ( £ „Transferring a call to another handset“, Page 75). Accepting/rejecting call waiting during an internal callIf you receive an external call during an internal call, you will hear the call waiting tone (short tone). With Caller ID, the caller's number or name will appear in the display. Ending an internal call, accepting an external call§Menu§ ¢Accept Call Waiting Select and press §OK§.The internal call is ended. You are connected to the external caller.Rejecting an external call (only possible for calls to your fixed line network number)§Menu§ ¢Reject Call Waiting Select and press §OK§.The call waiting tone is turned off. You remain connected with the internal par-ticipant. The ringer melody can still be heard on the other registered handsets.
77Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Handset settingsYour handset is preconfigured, but you can change the settings to suit your individual requirements.Changing the date and timeTo manually change the time, open the input field with:§Menu§ ¢Settings ¢Date/TimeSelect and press §OK§. Enter Date:  Enter the month, day and year in 8-digit format, e.g. QQ2QQO for 10/1/2009.Enter time: Enter the hours and minutes in 4-digit format, e.g. QM5for 07:15 AM.Press the Display key am/pm to switch between am and pm.§OK§ Press the Display key.Changing the display languageYou can view the display texts in different languages.§Menu§ ¢Settings ¢Handset ¢LanguageSelect and press §OK§. The current language is indicated by a ‰.qSelect a language and press §OK§. a Press and hold (idle status). If you accidentally choose a language you do not understand:§Menu§ M32 Press keys in sequence.q  Select the correct language and press §OK§.Please noteThe address of a time server on the Internet is stored on your telephone. The date and time are taken from this time server provided that the base sta-tion is connected to the Internet and synchronization with the time server is activated (£Page 139). Manual settings are overwritten in this case.
78Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Activating/deactivating the screensaverYou can have a screensaver displayed on the handset. The screensaver replaces the display screen when the handset is in idle status. It hides the date, time and internal name. You have the following options:No Screensaver The screensaver is deactivated. The idle display status (£Page 1) is dis-played. Digital Clock Approx. 10 seconds after the handset returns to idle status, a digital clock appears on the display.Info Services Approx. 10 seconds after the handset returns to idle status, a digital clock and (if available) text information from the Internet appear in the display (e.g. weather reports, RSS feeds). The text information is displayed below the clock as a scrolling message. Parts of the menu are not displayed in the language selected ...... and three or more handsets are registered on your base station. A language that is not one of the standard languages for the base station (= English (North America), Français (Amér. du Nord), Español) is set on at least three handsets. Cause: Some display texts are only stored for the standard languages English, Français and Español on your base station. In addition, these display texts can be stored in the base station in two other languages or in another language for two different types of Gigaset handsets. When selecting the language on the handset, these texts are downloaded to the base station from the Internet. If another non-standard language is set on a third handset, then display texts appear in one of the standard languages on this handset. Both the non-standard languages, which are set on the handsets with the lowest internal numbers, are stored on the base station.If there is no further handset registered on the base station whose type and language setting correspond to an additionally loaded language, then the memory is freed up. If necessary, the language set for another registered handset is loaded onto the base station. 10:3310:33IP info10:33IP info10:33P info IP
79Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008The text information is initially displayed once. Then the digital clock is displayed by itself. The text information is displayed again when: – New information is received – You remove the handset from the charging cradle or place it in the charging cradle– You press any key on the handset. The display backlight switches itself on. The text information can be made up of separate pieces of information (£Page 133). The weather report is preset. Setting the screensaver§Menu§ ¢Settings ¢Handset ¢Display ¢ScreensaverThe current setting is displayed. No Screensaver / Digital Clock / Info Services Select and press §OK§. A brief preview of the selected screensaver is displayed. The selection is marked with ‰. a Press and hold (idle status). The selected screensaver is displayed after approx. 10 seconds. Quickly accessing functionsThe §z§ function (open the Last Number Redial list) is preset on the left Display key of your handset. You can change the configuration, i.e. assign a different function to the Display key.To start the function, you then simply need to press the button. Changing the assignment of the Display key¤When the handset is in idle status, press and hold the left Display key.¤Select a function with the Control key q and press §OK§. The following features are available: uINT (§INT§) Open the list of internal participants with the k key.Please noteuIf you have set the screensaver Info Services, and you want to make a call or change settings on the handset, you may, if necessary, need to repeat the first key press (e.g. press the §Menu§ key twice to open the main menu). The first key press activates the display of text information. uThe screensaver is not displayed in certain situations, e.g. during a call or if the handset is de-registered. uIf the screensaver conceals the display, press the End Call key a briefly to show the idle display with time and date.
80Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008uFixed Line call (§Phone§)Opens the predialing option for making a call via the fixed line network.uIP call (§IP§)Opens the predialing option for making a call via VoIP.Activating/deactivating auto answerIf you activate this function, when you receive a call you can simply lift the handset out of the charging cradle without having to press the Talk key c.§Menu§ ¢Settings ¢HandsetAuto AnswerSelect and press §OK§ (‰=on).a Press and hold (idle status). Changing the handsfree/earpiece volumeYou can adjust the volume for handsfree talking to one of five settings (1-5, e.g. volume 3 = Š) and the earpiece volume to one of three (1-3, e.g. volume 2 = ‰). Setting the volume during a callThe setting applies to the current mode (earpiece or handsfree).You are conducting an external call. tPress up on the Control key.q  Set the volume.The setting will automatically be saved after approx. 3 seconds, if not then press the display key §OK§.If t is assigned with another function:§Menu§ Open menu.Volume Select and press §OK§.q  Set the volume.Adjusting the volume via the menutBriefly press up on the Control key.Call Volume Select and press §OK§.Earpiece Volume / Handsfree VolumeSelect and press §OK§.q  Adjust the volume and press §OK§.aPress and hold (idle status). Please noteYou can also adjust the volume via §Menu§ £Settings £Audio Settings £Call Volume.
81Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Setting ringersuVolume:You can choose between five volumes (1–5; e.g. volume 3 = ˆ) and the "crescendo" ring (6; volume increases with each ring = ‡). uRinger melodies:You can select various ringers from a list of pre-loaded ringer melodies. The first three melodies are "classical" ringers.You can set different ringer melodies for the following functions:uExternal Calls: for external callsuInternal Calls: for internal callsuAlarm Clock: for the alarm clockSetting the ringer volumeThe ringer volume is the same for all types of ring.When the handset is in idle status:tBriefly press up on the Control key.Ringer VolumeSelect and press §OK§.q  Adjust the volume and press §OK§.Setting the ringer melodySet different ringer melodies for external calls, internal calls and the alarm clock. tBriefly press up on the Control key.Ringer MelodySelect and press §OK§.External Calls / Internal Calls / Alarm Clock Select and press §OK§.qSelect melody (‰=on) and press §OK§.aPress and hold (idle status). Please noteYou can also adjust the ringer volume via §Menu§ £Settings £Audio Settings £Ringer Volume.Please noteYou can also adjust the ringer melody via §Menu§ £Settings £Audio Settings £Ringer Melody.
82Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Activating/deactivating the ringerYou can deactivate the ringer on your handset before you answer a call or when the handset is in idle status; the ringer can be deactivated permanently or just for the current call. The ringer cannot be re-activated while an external call is in progress.Deactivating the ringer permanently*Press and hold the Asterisk key until the Ú icon appears in the dis-play.Reactivating the ringer*Press and hold the Asterisk key in idle status.Deactivating the ringer for the current call§Menu§ Open menu.Silent Select and press §OK§.Activating/deactivating advisory tonesYour handset uses various advisory tones to tell you about different activities and statuses. uKey click: every key press is confirmed.uConfirmation tone (ascending tone sequence): at the end of an entry/setting and when a new entry arrives in the Calls listuError tone (descending tone sequence): when you make an incorrect entryuMenu end tone: when scrolling to the end of a menu You cannot deactivate the confirmation tone for placing the handset in the base station.tBriefly press up on the Control key.Advisory TonesSelect and press §OK§ (‰=on).aPress and hold (idle status).
83Handset settingsGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Setting the battery low toneThe battery warning tone advises that the batteries need to be charged. You can activate it, deactivate it or decide whether or not it should sound during a call. tBriefly press up on the Control key.Battery Low Select and press §OK§.On / Off / During CallSelect and press §OK§ (‰=on). aPress and hold (idle status). Restoring the handset default settingsEach individual handset setting is reset – in particular the language, display, volume, ringer melodies and alarm clock settings (£Page 77). The Last Number Redial list is cleared. This will not affect entries in the directory, Calls list or the handset's registration to the base station.§Menu§ ¢Settings ¢Handset ¢Reset Handset§OK§ Press the Display key.You can cancel the factory reset by pressing a or the Display key .aPress and hold (idle status).
84Setting the base station via the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Setting the base station via the handsetThe base station settings are performed using a registered Gigaset A58H handset.Some settings can also be carried out via the base station Web configurator. The ú icon identifies functions that you can perform via the Web configurator. Protecting against unauthorized accessProtect the system settings of the base station with a PIN known only to yourself. The system PIN must be entered, for example, when activating and deactivating the handset, when changing the VoIP settings, with firmware updates, when resetting the base station default settings and for launching the Web configurator.Changing the system PINYou can change the 4-digit system PIN set on the base station (default setting: 0000) to a 4-digit PIN known only by you.§Menu§ ¢Settings ¢Base ¢System PIN~Enter the current system PIN and press §OK§. ~Enter your new system PIN and press §OK§. ~Now re-enter the new system PIN and press §OK§. For security reasons, "****" is displayed instead of the system PIN.a Press and hold (idle status). Resetting the system PINIf you have forgotten your system PIN, you can reset the base station to the original PIN 0000. To do this, you must reset your base station using the key on the base station ( £ Resetting the base station using a key on the base station on Page 85). Please note that this will restore all other base station settings too (£Page 85).
85Setting the base station via the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Restoring the base station to the factory settingsResetting the base station via the menuEach individual setting is reset, in particular:uVoIP settings such as VoIP provider and account data and DTMF settings (£Page 89, Page 106, Page 126)uSettings for the local network (£Page 91, Page 103)uDefault connection (£Page 86) uThe names of the handsets (£Page 74) uEco mode is deactivated (£Page 69)uPABX connection settings (£Page 94) Calls list is deleted.The following are not reset:uDate and time uSystem PIN The handsets are still registered.§Menu§ ¢Settings ¢Base ¢Base Reset ~Enter the system PIN and press §OK§. §OK§ Press the display key to confirm.Resetting the base station using a key on the base stationAs with resetting the base station via the menu, all individual settings are reset. The system PIN will also be reset to 0000 and only the handsets registered to the base station at delivery are registered.¤Remove the cable connections from the base station to the router (£Page 20) and fixed line network (£Page 19).¤Remove the base station power adapter from the socket (£Page 19).¤Press and hold the Registration/Paging key (£Page 2).¤Plug the power adapter back into the electrical socket.¤Press and hold the Registration/Paging key (at least 10 sec.).¤Release the Registration/Paging key. The base station has now been reset.You will then need to "prepare to use" the base station again, i.e. re-establish the cable connections to the fixed line network and the router and make the settings for VoIP telephony (£Page 21). Please noteFor further information about reregistering the handsets after resetting, where applicable, £Page 71.
86Setting the base station via the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Activating/deactivating music on hold§Menu§ ¢Settings ¢Base Music on holdSelect and press §OK§ to activate or deactivate the music on hold (‰=on).Setting default connectionYou can make settings according to whether you want to make calls via VoIP or the fixed line network as standard.§Menu§ ¢Settings ¢Base ¢Telephony ¢Default Line TypeIP / Fixed LineSelect and press §OK§ (‰=on).When making calls:¤Briefly press the Talk key c to make a call via this default connection. ¤Press and hold the Talk key c to make the call via the other connection type. úFor information on making the setting on the Web configurator, £Page 119. Please noteThe default connection is only relevant when dialing numbers that are not sub-ject to dialing plans (£Page 123) and are entered without a line suffix (£Page 38).
87Setting the base station via the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Entering local and extra area codesUse the following guidelines to make local calls (calls to the local fixed line net-work):uDepending on the exchange, area codes are not dialed for local calls via your fixed line network. However, all calls are stored in the Calls list with access codes. To call back a caller using the Calls list, you must store the local area code in the phone in whose area your phone is being used. If your phone is in a "multiple area code" area, you must also enter the other area codes that belong to this area as extra codes.uWith local calls via your VoIP connection the area code must also be dialed. If you have stored your area code in the phone and activated the Predial area code for local calls through VoIP option (£Page 122), the area code entered is dialed automatically when dialing numbers without an area code (e.g. when dialing from the directory).úFor entering the area code with the Web configurator, £Page 122. Entering a local area code§Menu§ ¢Settings ¢Base ¢TelephonyArea Code Select and press §OK§.~Enter a local area code (permitted characters (maximum 3) are "*", "#") and press §OK§.aPress and hold (idle status).Entering extra codes§Menu§ ¢Settings ¢Base ¢TelephonyExtra Codes Select and press §OK§.qSelect entry ("–––" = blank entry).XIf necessary, delete an existing extra code. ~Enter an extra code (permitted characters (maximum 3) are "*", "#") and press §OK§.Repeat the above steps until you have entered all the extra codes for your area. A maximum of 5 extra codes can be stored.aPress and hold (idle status).Updating the base station firmwareIf necessary, you can update your base station firmware.The firmware update is downloaded directly from the Internet by default. The relevant Web page is preconfigured in your phone.
88Setting the base station via the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Prerequisite: The base station is in idle status, i.e.:uNo calls are being made via the fixed line network or VoIP.uThere is no internal connection between registered handsets or to GHC devices. uNo other handset has opened the base station menu. Starting the firmware update manually§Menu§ ¢Settings ¢Base Firmware UpdateSelect and press §OK§.~Enter the system PIN and press §OK§. The base station is connected to the Internet. §Yes§ Press the Display key to start the firmware update.Automatic firmware update Your phone will check daily whether a more recent firmware version is available on the Gigaset configuration server on the Internet. If this is the case, the mes-sage New firmware available is displayed when the handset is in idle status, and the Message key fflashes.f Press the Message key.§Yes§ Press the Display key to confirm the prompt. The firmware will be loaded onto your phone. If you respond to the prompt with §No§, the handset changes to idle status. Your phone will then remind you again about the firmware update at a later date (New firmware available is displayed again). However, you can also carry out a firmware update manually (£Page 88). úYou can deactivate the automatic version check via the Web configurator (£Page 138). Please noteuThe firmware update can last up to 3 minutes.uWhen updating from the Internet, checks are made to ensure that no newer version of the firmware exists. If this is not the case, the operation is termi-nated and a message is issued to that effect. Please noteIf the telephone is not connected to the Internet at the time when the check for new firmware is to be carried out (e.g. because the router is deactivated), the check is carried out as soon as the phone is reconnected to the Internet.
89Making VoIP settings on the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Making VoIP settings on the handsetTo use VoIP, you must set a few parameters for your phone. You can make the following settings using your handset. uDownload the general access data for your VoIP provider from the Gigaset configuration server and store it on your phone. uEnter your personal access data for your first VoIP account (first VoIP phone number). You can configure the access data for five further VoIP accounts via the phone's Web configurator. uSet the phone's IP address in the LAN. The connection wizard on your phone can help you make the settings. úYou can set these and other parameters conveniently via the Web configurator on a PC connected to your local network (£Page 96).Using the connection wizardThe connection wizard starts automatically when you set the handset and base station up for the first time, or when you try to connect to the Internet before making the necessary settings. You can also start the connection wizard via the menu:§Menu§ ¢Settings ¢Base ¢TelephonyConnection WizardSelect and press §OK§. ~Enter the system PIN and press §OK§. For entering VoIP settings using the connection wizard, £Page 21.Changing settings without the connection wizardYou can change your provider's VoIP settings and the VoIP user data via the menu without starting the connection wizard.Downloading your VoIP provider's settingsThe general settings for various VoIP providers are available to download on the Internet. The relevant Web page is preconfigured in your phone.Prerequisite: Your phone is connected to the Internet.§Menu§ ¢Settings ¢Base ¢Telephony ¢ VoIP~Enter the system PIN and press §OK§. Select VoIP ProviderSelect and press §OK§. The phone establishes a connection to the Internet.qSelect country and press §OK§. qSelect your VoIP provider and press §OK§. Your VoIP provider data is downloaded and saved in your phone.
90Making VoIP settings on the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008If only one provider is available, the countries and providers lists are not dis-played. Only the name of this provider will then appear in the display. To start the download, confirm with §OK§. úIf your VoIP provider is not included in the list, you need to enter or adjust the general VoIP settings manually via your phone's Web configurator, £Page 107.Automatic update for the VoIP provider settings After the first download of the VoIP provider settings, your phone will check daily whether a newer version of the file for your VoIP provider is available via the Internet on the Gigaset configuration server. If this is the case, the message New profile available is displayed when the handset is in idle status, and the Mes-sage key fflashes.f Press the Message key.§Yes§ Press the Display key to confirm the prompt. ~Enter the system PIN and press §OK§. The new data for your VoIP provider will be downloaded and saved on the phone. If you respond to the prompt with §No§, the display will not be repeated. The message New profile available will only be shown again if a newer version of the VoIP settings than the one rejected is available. Entering/changing VoIP user dataYou must complete the VoIP settings with your personal data. You will receive all necessary data from your VoIP provider.§Menu§ ¢Settings ¢Base ¢Telephony ¢ VoIP ~Enter the system PIN and press §OK§.  Username / Authentication Name / Authentication PasswordSelect and press §OK§ one after the other.~Enter/change the user data and press §OK§. When making these entries, please remember the VoIP user data is case sensitive. To enter text £Page 152.Enter the caller ID for your VoIP provider account as the  Username. The  User-name is usually identical to your Internet phone number (the first part of your SIP address £Page 110). For Authentication Name and Authentication Password enter the provider-depend-ent access data that has to be transferred by the phone to the SIP service at reg-istration. Please noteIf an error occurs during the download, an error message is displayed. You can find possible messages and measures in the table on Page 141. Please noteA previously set password is not displayed.
91Making VoIP settings on the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Setting the phone's IP address in LANThe base station requires an IP address in order to be "recognized" by the LAN (the router). The IP address can be assigned to the base station automatically (by the router) or manually. uIf performed dynamically, the router's DHCP server automatically assigns the base station an IP address. The base station's IP address can be changed according to router settings.uIf performed manually/statically, you assign the base station a static IP address. This may be necessary depending on your network configuration. úFor information on making the local network settings on the Web configurator, £Page 103. Activating/deactivating dynamic assignment§Menu§ ¢Settings ¢Base ¢Local Network~Enter the system PIN and press §OK§. Dynamic IP address (‰=on) Select and press §OK§ to change the current settings.If you deactivate dynamic assignment, you must set the IP address and subnet mask of the base station, the default gateway and DNS server manually. A corresponding message is displayed.Viewing/changing the base station IP addressYou can only change the IP address if you have deactivated dynamic assign-ment.192.168.2.2 is the default.§Menu§ ¢Settings ¢Base ¢Local Network~Enter the system PIN and press §OK§. IP Address  Select and press §OK§. The current IP address is displayed.~If necessary, enter the IP address and press §OK§. For information on the IP address, please see Page 103 and the glossary on Page 178. Please noteTo assign the IP address dynamically, the DHCP server on the router must be activated. Please also read the user guide for your router.
92Making VoIP settings on the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Viewing/changing the subnet maskYou can only change the subnet mask if you have deactivated dynamic assign-ment.255.255.255.0 is the default.§Menu§ ¢Settings ¢Base ¢Local Network~Enter the system PIN and press §OK§. Subnet MaskSelect and press §OK§. The current subnet mask is displayed.~If necessary, enter the subnet mask and press §OK§. For information on the subnet mask, please see Page 103 and the glossary on Page 182. Viewing/changing the DNS serverEnter the IP address for the preferred DNS server. The DNS server (Domain Name System) converts the symbolic name of a server (DNS name) into the public IP address for the server when the connection is made.You can specify your router's IP address here. The router forwards phone address requests to its DNS server. 192.168.2.1 is the default.§Menu§ ¢Settings ¢Base ¢Local Network~Enter the system PIN and press §OK§. DNS Server Select and press §OK§. ~If necessary, enter the IP address of your preferred DNS server and press §OK§. Viewing/changing the default gateway to the InternetEnter the IP address for the default gateway, by means of which the local net-work is connected to the Internet. This is generally the local (private) IP address for your router (e.g. 192.168.2.1). Your phone requires this information to access the Internet. 192.168.2.1 is the default.§Menu§ ¢Settings ¢Base ¢Local Network~Enter the system PIN and press §OK§. Default GatewaySelect and press §OK§. ~If necessary, enter the IP address of the default gateway and press §OK§.
93Making VoIP settings on the handsetGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Activating/deactivating the display of VoIP status messagesIf the function is activated, a VoIP status code for your service provider is displayed. Activate the function if, for example, you have problems with VoIP connections. You will receive a provider-specific status code, which supports the service when the problem is analyzed. You will find a table with the possible status screens in the appendix (£Page 145).§Menu§ ¢Settings ¢Base ¢Telephony ¢VoIP~Enter the system PIN and press §OK§. Status on HSSelect and press §OK§ (‰=on).aPress and hold (idle status). úFor information on making the setting on the Web configurator, £Page 140. Checking the base station MAC addressDepending on your network configuration, you may have to enter your base station MAC address, for example, into your router's access Control list. You can check your base station MAC address:§Menu§ M4OM5 The base station MAC address is displayed.aPress and hold (idle status). úFor information on checking your MAC address on the Web configurator, £Page 140.
94Operating the base station on the PABXGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008Operating the base station on the PABXThe following settings are only necessary when your PABX requires them; see the PABX user guide. The settings only affect fixed line network connections.Changing the dialing modeYou can set the dialing mode.§§Menu§ ¢Settings ¢Base ¢Telephony ¢Fixed line ¢Dialing ModeTone / PulseSelect and press §OK§ (‰=on).a Press and hold (idle status). Setting recallYour phone is preset at the factory for operation on the main connection (recall 250 ms). For operation on a PABX, you may have to change this value. Please refer to the user guide for your PABX.§§Menu§ ¢Settings ¢Base ¢Telephony ¢Fixed line ¢RecallqSelect recall and press §OK§. The current setting is indicated by ‰.a Press and hold (idle status). Setting access codes (external line prefixes)Depending on your PABX, to obtain an external line you must dial an access code before making external calls. You can store this access code in your phone. It is then added automatically to the numbers, e.g. when dialing using the Calls list. §Menu§ ¢Settings ¢Base ¢Additional FeaturesAccess CodeSelect and press §OK§.~Enter or edit the access code (maximum 3 characters) and press §OK§. a Press and hold (idle status). Please note uSuffix dialing (for selecting the connection) is not possible in conjunction with pulse dialing: a pound "#" is displayed during dialing but ignored when pulse dialing is used. uEnter an asterisk "*" to switch temporarily to touch tone dialing. The asterisk is not displayed.
95Operating the base station on the PABXGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / settings_bs_hs_pabx.fm / 24.04.2009Version 8, 03.09.2008If an access code is set, the following applies:uThe access code is added automatically when dialing from the Calls list and when dialing emergency numbers.uWhen dialing manually and dialing numbers from the directory, you must add the access code yourself.Setting pauses Changing pause after line activityYou can set the length of the pause inserted between pressing the Talk key c and sending the phone number. §Menu§ M4OL ~Enter a number for the length of the pause (1=1sec.; 2=3sec.; 3= 7 sec.) and press §OK§.Changing the pause after the Flash keyYou can change the length of the pause if your PABX requires this (refer to the user guide for your PABX). §Menu§ M4O ~Enter a number for the length of the pause (1=800 ms; 2= 1600 ms; 3= 3200 ms) and press §OK§. Switching temporarily to touch tone dialing (DTMF)If your PABX still operates with dial pulsing (DP), but you need touch tone dial-ing for a connection (e.g. to listen to the network mailbox for your fixed line network connection), you must switch to touch tone dialing for the call.Prerequisite: You are currently conducting an external call via the fixed line network or you have dialed an external fixed line network number or an exter-nal call is signaled.§Menu§ Open menu.Tone dialing Select and press §OK§.Touch tone dialing is now activated for this call only.
96Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Setting the phone with the PCThe Web configurator is the Web interface for your phone. It allows you to select the settings for your phone's base station via your PC's Web browser. The Web configurator on your phone provides you with the following options:uConfigure your phone access to the local network (IP address, gateway to the Internet).uConfigure your phone for VoIP. Assign up to six VoIP phone numbers to your telephone.uLoad new firmware onto the phone if necessary.uUse Internet services: display text information on the handset (info services). uSynchronize the telephone's date/time with a time server on the Internet. uCopy contacts from the Outlook address book on your PC into the handset directories or back up your handsets' directories on your PC. uManage the names and internal numbers of registered handsets and your local directories uObtain information about your phone's status (firmware version, MAC address, etc.).Prerequisites: uA standard Web browser is installed on the PC, e.g. Internet Explorer version 6.0 or higher, or Firefox version 1.0.4 or higher.uThe phone and PC are connected with each other via a router. Connecting the PC with the telephone's Web configurator Prerequisite: The settings of an available firewall installed on your PC allow the PC and phone to communicate with each other.There are two ways of connecting your PC to the base station Web configurator: uVia the (local) IP address of the base stationuVia Gigaset config Please noteuDepending on your VoIP provider, it is possible that you will be unable to change individual settings in the Web configurator. uThe phone is not blocked while you select your settings in the Web config-urator. You can also use your phone to make calls or change base station or handset settings on your handset at the same time. uWhile you are connected to the Web configurator, it is blocked to other users. It cannot be accessed by more than one user at any time.
97Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Establishing a connection via the IP address:¤Establish the telephone's current IP address on the handset:You can see the phone's current IP address in the handset display by briefly pressing the Registration/Paging key on the base station. Your phone's IP address can change if you have activated dynamic IP address assignment (£Page 103). ¤Launch the Web browser on your PC. ¤Enter http:// and the telephone's current IP address (for example: http://192.168.2.2) into the address field of the Web browser. ¤Press the Return key. A connection is established to the phone's Web configurator. Establish a connection via Gigaset config:Prerequisite: The router is connected to the Internet and your PC can access the Internet via the router.¤Launch the Web browser on your PC. ¤Enter the following URL into the Web browser's address field:http://www.Gigaset-config.com.¤Press the Return key. You will receive a message stating that the connection will be forwarded to your base station. If several Gigaset VoIP phones can be reached via your Internet connection, you will be asked to which one of these phones you would like to be connected.After successfully forwarding the connection, the Login Web page of the Web configurator is displayed in the Web browser.WarningIf one of the four parts of the IP address contains leading zeros (e.g. 002), these zeros must not be entered in the Web browser address field. Other-wise the Web browser will not be able to establish a connection to the Web configurator.Example: The IP address 192.168.002.002 is displayed on the handset. Enter 192.168.2.2 in the address field.Please noteThe connection between the PC and the Web configurator is a local connection (LAN connection). The Internet is only accessed to establish the connection.
98Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Logging in, setting the Web configurator languageOnce you have successfully established the connection, the Login Web page is displayed in the Web browser.You can select the language you want the menus and Web configurator dia-logues to be displayed in. The language that is currently selected is displayed in the top field of the Web page. ¤If necessary, click   to open the list of available languages. ¤Select the language. ¤Enter your phone's system PIN (default setting: 0000) in the bottom field of the Web page, to access the Web configurator functions. ¤Select OK.Once you have successfully logged in, a Home screen opens with general infor-mation on the Web configurator.If you enter an incorrect system PIN, a corresponding message is displayed. You will be prompted to re-enter the PIN. If you enter an incorrect system PIN a second time, the PIN field will be blocked for a short time (grayed out). The duration of the block will double each time a PIN is subsequently entered incorrectly. Logging offIn the menu bar (£Page 99) at the top right of every Web page in the Web configurator, you will see the Log Off command. Select Log Off to log off from the Web configurator. Please noteuIf you have forgotten your system PIN, you must restore your device's fac-tory settings. Please note that this will restore all other settings too (£Page 85). uAfter approximately 10 minutes of inactivity, you will be automatically logged off. The next time you try to make an entry or open a Web page, the Login Web page is displayed. Enter the system PIN again to log in back. uAny entries that you did not save on the phone before automatic log-off will be lost.WarningAlways use the Log Off command to end the connection to the Web configura-tor. If, for example, you close the Web browser without logging off before-hand, it is possible that access to the Web configurator will be blocked for a few minutes.
99Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Using the Web pagesThe Web pages contain the UI elements displayed in Figure 2. Menu barIn the menu bar, the Web configurator menus are displayed in the form of tab pages. The following menus are available: Home  The start screen is opened once you have registered with the Web configurator. It contains information on the Web configurator functions.Settings This menu allows you to make settings on your phone (£Page 102).If you select the Settings menu, a list with this menu's functions is displayed in the navigation area (£Page 100). Status This menu provides you with information about your phone (£Page 140).Log Off You will find the Log Off function to the right of the menu bar on every Web page (£Page 98).Figure 2 Example of the structure of a Web pageWorking areaNavigation area Menu barButtons
100Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Navigation areaIn the navigation area, the functions of the menu selected in the menu bar (£Page 99) are listed. If you select a function, the associated page opens in the working area with information and/or fields for your inputs. If a function is assigned subfunctions, these are displayed with the function as soon as you select the function. The relevant page for the first subfunction is displayed in the working area.Working areaDepending on the function selected, information or dialog boxes are displayed in the working area, which allow you to make or change your phone settings. Making changesSettings can be changed via input fields, lists or options. uThere may be restrictions regarding the possible values for a field, e.g. the maximum number of characters, entering special characters or certain value ranges.uTo open a list, select  . You can select from preset values.uThere are two kinds of options: – Options in a list, from which you can activate one or several options. Active, i.e. selected options are highlighted with  , non-active options with  . You can activate an option by selecting  . The status of the other options in the list does not change. You can deactivate an option by selecting . – Alternate options. The active option in the list is highlighted with  , and the non-active with  . You can activate an option by selecting  . The previously activated option is deactivated. You can only deactivate an option by activating another option. Entering Cyrillic and Arabic charactersIn the following, the specified maximum number of characters permitted in a field refers to Latin characters and digits (1 character = 1 byte), i.e. 1 character means 1 byte. Cyrillic and Arabic characters require 2 bytes each, i.e. with a field length of 16 characters, for example, you can enter a maximum of 8 Cyrillic or Arabic characters. If you enter too many characters into a field, the entry will be rejected (not saved on the base station). The "old" field content (e.g. the default settings) remains in place and is displayed again when the web page is updated. No warning/confirmation is given. Please noteAn overview of the Web configurator menu £Page 37.
101Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Applying changesAs soon as you have made your change on a page, activate the new setting on the phone by selecting Set.If your input in a field does not comply with the rules for this field, an appropri-ate error message is displayed. You can then repeat the input.ButtonsButtons are displayed in the bottom section of the working area. Set Save entries on the phone.Cancel Reject changes made on the Web page and reload the settings that are cur-rently saved in your phone to the Web page. Opening Web pagesA brief outline of the navigation to the individual Web configurator functions is given below. WarningChanges that have not been saved on your phone are lost if you move to another Web page or if the Web configurator is logged off, e.g. due to exceed-ing the time limit (£Page 98).ExampleSetting DTMF signaling Settings ¢Telephony ¢Advanced Settings To open the Web page, carry out the following steps after registration: ¤Select the Settings menu in the menu bar. ¤Select the Telephony function in the navigation area.The Telephony subfunctions are displayed in the navigation tree.¤Click the Advanced Settings subfunction. The Web page from Figure 2 will be shown in the Web browser.
102Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Setting the phone with the Web configuratorYou can make the following settings using the Web configurator: uConnect your phone to the local network (£Page 103).uConfiguration for telephony:– Enter settings for the VoIP provider and configure or activate/deactivate VoIP accounts (£Page 107).– Specify the name of the fixed line network (£Page 114).– Activate/deactivate the Gigaset.net connection (£Page 114).– Activate/deactivate call forwarding for calls to your VoIP numbers or to your Gigaset.net number (£Page 121).– Configure settings to improve voice quality for the VoIP connections (£Page 115).– Define the default connection for your telephone (fixed line network or VoIP) (£Page 119).– Assign VoIP phone numbers to the individual handsets (£Page 120).– Define user-specific dialing plans for emergency numbers and for cost control purposes (£Page 123).– Enter and activate/deactivate the network mailbox for each number assigned to the telephone (£Page 125).– Define the type of DTMF signaling (e.g. for remote operation of a VoIP network mailbox) and the Flash key function for VoIP (£Page 126).– Enter settings for call forwarding via VoIP (call placing, i.e. connecting two external callers to each other, £Page 127).uOutput of information from an IP info service on the handset (£Page 133).uSynchronize date and time on the base station with a time server on the Internet (£Page 139).uStart firmware updates (£Page 137).uManage registered handsets:– Change names and internal numbers of the registered handsets (£Page 133).– Copy contacts from your PC's Outlook address book to the handset direc-tories or save handset directories to your PC (£Page 134).– Activate/deactivate the display of VoIP status messages on your handset (£Page 136).
103Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Configuring the IPAssigning the IP addressSelect the necessary settings for operating your phone in your local network and to connect it to the Internet. For more detailed explanations of the individ-ual components/terms, see the glossary (£Page 172). ¤Open the following Web page: Settings ¢IP Configuration. ¤In the Address Assignment area, select the IP address type. Select Obtained automatically to use a dynamic IP address assigned by a DHCP server in your local network. No further settings are necessary for the local net-work. Select Static to set up a static local IP address for your phone. A static IP address is, for example, useful if port forwarding or a DMZ is set up on the router for the phone.The following fields are displayed when you select IP address type = Static:IP address Enter an IP address for your phone. This IP address allows your phone to be reached by other subscribers in your local network (e.g. PC). 192.168.2.2 is the default.Please note the following:uThe IP address must be from the address block for private use that is used in the router. This is generally in the range 192.168.0.1 – 192.168.255.254 with Subnet mask 255.255.255.0. The subnet mask determines that the first three parts of the IP address must be identical for all subscribers in your LAN. uThe static IP address must not belong to the address block (IP pool range) that is reserved for the DHCP server of the router. It must also not be used by another device on the router.If necessary, check the settings on the router.Subnet maskEnter the subnet mask for your device's IP address. For addresses from the address block 192.168.0.1 – 192.168.255.254, the subnet mask 255.255.255.0 is generally used. This is preconfigured when the phone is sup-plied. Default gatewayEnter the IP address for the default gateway uses to connect the local network to the Internet. This is generally the local (private) IP address for your router (e.g. 192.168.2.1). Your phone requires this information to access the Internet. 192.168.2.1 is the default.
104Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Preferred DNS serverEnter the IP address for the preferred DNS server. DNS (Domain Name System) allows you to assign public IP addresses to symbolic names. The DNS server is required to convert the DNS name into the IP address when a connection is being established to a server.You can specify your router's IP address here. The router forwards phone address requests to its DNS server. 192.168.2.1 is the default.Alternate DNS server (optional) Enter the IP address for the alternate DNS server that should be used in situa-tions where the preferred DNS server cannot be reached.¤Select Set to save the changes.Or¤Select Cancel to reject the changes.After you have changed the IP configuration the base station is rebooted. You will be logged off by the Web configurator. The Login Web page is displayed again after the reboot.Allowing access from other networksThe default setting for your phone is set so that you can only access your phone's Web configurator via a PC that is in the same local network as your phone. The subnet mask of the PC must match that of the phone. You can also allow access from PCs in other networks. ¤Open the following Web page: Settings ¢IP Configuration. Area: Remote Management¤Activate the Yes option to permit access from other networks. To deactivate remote access, activate the No option Access is then limited to PCs in your own local network.Access to the Web configurator services from other networks is only possible if your router is set accordingly. The router must pass on the service requests from "outside" to Port 80 (default port) of the phone. Please also read the user guide for your router. To establish a connection, the public IP address or the DNS name of the router and, where applicable, the port number on the router must be indicated in the Web browser of the remote PC. WarningExpansion of access entitlement to other networks increases the risk of unau-thorized access. It is therefore recommended that you deactivate remote access again if you no longer require it.
105Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Entering an HTTP proxy server (only when connected to an internal company network)Direct connections between network participants and the Internet are often not permitted within internal company or organization networks (intranet). In such cases, all HTTP calls from the network are "transferred" by a proxy server. The proxy server is a computer or program within the network. If your phone is connected to such a network, you must store the address of this HTTP proxy server on the phone and activate handling of HTTP calls via the HTTP proxy server. Only then will you be able to access, for example, the Gigaset.net directory or obtain weather information, etc. in idle display (information services). ¤Open the following Web page: Settings ¢IP Configuration. Area: HTTP proxyEnable proxyClick the Yes option if your phone is to handle HTTP calls via your network's HTTP proxy server. If you select No, the phone attempts to access the Internet directly.Proxy server addressEnter the URL (£Page 183) of the proxy server to which your phone is to send HTTP calls. The proxy server then creates the connection to the Internet. Proxy server portSpecify the communication port used on the HTTP proxy server (number between 0 and 55000). Port 80 is usually assigned. ¤Select Set to save your settings.
106Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Configuring telephone connectionsYou can configure up to eight numbers on your phone: your fixed line network number, your Gigaset.net number and six VoIP numbers. You need to set up a VoIP account with a VoIP provider for each VoIP phone number. You must save the access data for each account and for the relevant VoIP provider in the phone. You can assign a name to each connection (VoIP and fixed line network). To configure the connections: ¤Open the following Web page: Settings ¢Telephony ¢Connections. A list (£Figure 3) will be shown containing all the possible connections that you can configure, or have already configured, on your phone. The list will show the following: Name / Provider Name of the connection. This will show the name that you have defined for the connection (£Page 108, Page 114) or the default name (IP1 to IP6 for VoIP connections, Fixed Line for the fixed line network connection and Gigaset.net). VoIP connections also display the name of the VoIP provider with which you have opened the account. If the name is unknown the display will show Other Provider.  Figure 3  List of possible connections
107Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Suffix Line suffix that you have to add to the phone number of an outgoing call to allow the account assigned to the suffix to be used as the sending account. Status  The status of the connection will be shown for VoIP connections: Registered The connection is activated. The phone has been successfully registered. You can use the connection to make calls. Disabled The connection is deactivated. The phone is not registering with the corre-sponding account with the VoIP service. You cannot use the connection to make or receive calls. Registration failed / Server not accessible Your phone was unable to register with the VoIP service, e.g. because the VoIP access data is incorrect or incomplete or the phone is not connected to the Internet. You can find further information in section "Getting help with your phone", £Page 141. Active You can use the option in the Active column to activate ( ) and deactivate ( ) VoIP connections. If a connection is deactivated, the phone will not register for this connection. The connection can be activated/deactivated by clicking directly on the option. The change does not need to be saved.To configure a connection or to change the configuration of a connection: ¤Select Edit button next to the connection.This will open a Web page where you can make the settings needed. More information is availableuIn the section "Configuring the VoIP connection", £Page 107 or uIn the section "Configuring the fixed line connection", £Page 114 oruIn the section "Configuring the Gigaset.net connection", £Page 114.Configuring the VoIP connection¤Open the following Web page: Settings ¢Telephony ¢Connections. ¤Select the Edit button next to the VoIP connection that you want to configure or the configuration you wish to change. This will open a Web page where you can make the settings that your phone needs to access your provider's VoIP server. The Web page always displays the following areas: uIP Connection (£Page 108), uAuto Configuration (£Page 108)ExampleIf you dial 123456765#1, the connection will be made and billed through the first VoIP account, regardless of the VoIP number you have assigned to your handset as the send number and whether you briefly press/press and hold the Talk key. If you dial 123456765#0, the connection will be made via the fixed line net-work.
108Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008uPersonal Provider Data (£Page 110). The areas uGeneral Provider Data (£Page 111) and uNetwork (£Page 111) can be shown and hidden by selecting the Show Advanced Settings and Hide Advanced Settings buttons. You must enter the VoIP provider's general access data in these areas. You can download this data for many VoIP providers from the Internet ( £ "Area: Auto Configuration", Page 108).¤Make the settings on the Web page.¤Save them in the phone £Page 113.¤Activate the connection if necessary £Page 114. Area: IP ConnectionConnection Name or Number Enter a name for the VoIP connection or the VoIP phone number (maximum 16 characters). This name is used to display the connection on the handset and the Web configurator interface, e.g. during allocation of send and receive num-bers (£Page 120), for the call display (£Page 42). Area: Auto ConfigurationThe entire configuration process or a large part of the configuration for a VoIP connection is automated for many VoIP providers. You can download the nec-essary VoIP access data to your phone from the Internet. You have the following options:uFully automated configurationPrerequisites: – You have received an auto configuration code from your VoIP provider. – The general access data for your VoIP provider is available for download-ing. You can download all the data required for VoIP access from the Internet:¤Enter the auto configuration code you received from your VoIP provider in the Auto Configuration area in the Auto Configuration Code field (maxi-mum 32 characters).¤Select the Start Auto Configuration button. The telephone establishes a connection to the Internet and downloads all data required for the VoIP connection, i.e. the general provider information and your personal provider data (account data) are saved to your base sta-tion. If you have already entered details on the Web page, this is deleted as soon as Start Auto Configuration is selected. The fields in the Personal Provider Data and General Provider Data areas and the server addresses in the Network area are overwritten by the downloaded data.
109Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Generally, you should not have to enter any additional data on this Web page. When the download is complete, the Connections list is displayed. ¤Activate the connection as described on Page 114. You can then be reached on the corresponding VoIP phone number. uAutomatic configuration of general VoIP provider data Prerequisite: You have received your account details from your VoIP pro-vider (e.g. Authentication Name, Authentication password). Profile files for the most important VoIP providers are available to download from the Internet via the Gigaset configuration server. The address for the server is stored in your phone (£Page 137).To load the data onto your telephone, proceed as follows: ¤Select Select VoIP Provider in the Auto Configuration area. This will display information on the download procedure. The download procedure consists of several steps:¤Select the Next button.¤From the list, select the country for which the list of VoIP providers is to be loaded.¤Select the Next button. ¤Select your VoIP provider from the list. If your provider is not included in the list, select Other Provider. In this case you will have to enter the general provider data by hand (see "Area: Gen-eral Provider Data" and "Area: Network" below).¤Select the Finish button. The details of the selected provider are loaded to your phone and saved under General Provider Data (£Page 111) and Network (£Page 111). You cannot make any further entries in these areas. Please noteIf the message Download of settings not possible! File is corrupt! appears, no data will be loaded onto the phone. Possible causes of this are:uThe incorrect code has been entered (e.g. upper/lower case rules have not been followed). If necessary, enter the code again. uThe file that has been downloaded is invalid. Please consult your VoIP provider. Please noteIf you select the Select VoIP Provider button, any changes that have been made to the Web page will be saved and checked. Values may need to be corrected before the Select VoIP Provider operation is started. Please noteIf only one provider is available, the countries and providers lists are not displayed. The name of the provider is then displayed directly.
110Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008The Provider field shows the name of the selected provider or Other Provider. A link to the provider's homepage is displayed where available.To complete configuration of your VoIP connection, enter your account data in the Personal Provider Data area. Area: Personal Provider DataEnter the configuration data that is necessary for accessing your VoIP provider's SIP service. This data can be obtained from your VoIP provider.The field names in this area (Authentication Name, etc.) listed in the following are standard names and may change. If you have already downloaded the pro-vider's general details ("Select VoIP Provider" button, see above), field entries will be replaced by provider-specific names to facilitate orientation (e.g. SIP-ID instead of Authentication Name). Authentication Name Specify the registration or authentication ID agreed with your VoIP provider (maximum 32 digits). The registration ID serves as the access ID that your phone must specify when registering with the SIP proxy/registrar server. The Authentication Name is usually identical to the Username, i.e. to your Internet phone number. Authentication password Enter the password that you have agreed with your VoIP provider in the Authen-tication password field (maximum 32 characters). The phone needs the pass-word when registering with the SIP proxy/registrar server. Username Enter the caller ID for your VoIP provider account (maximum 32 characters). This ID is usually identical to the first part of your SIP address (URI, your Internet phone number). Display name (optional)Enter any name that should be shown in the other caller's display when you call them via the Internet (example: Anna Sand). All characters in the UTF8 charac-ter set (Unicode) are permitted. The name must not exceed 32 characters.If you do not enter a name, your Username or your VoIP phone number is dis-played. Ask your VoIP provider if this feature is supported. Please noteAfter the first download of the VoIP provider settings, your phone will check daily whether a newer version of the file for your VoIP provider is available via the Internet on the Gigaset configuration server (£Page 90). ExampleExample: If your SIP address is "987654321@provider.com", enter "987654321" as the Username.
111Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Area: General Provider DataIf you have downloaded the general settings for the VoIP provider from the Gigaset configuration server (£Page 108), then the fields in this area will be preset with the data from the download. Generally, you do not need to config-ure any settings in this area.Domain Specify the last part of your SIP address (URI) here (maximum 74 characters). Proxy server addressThe SIP proxy is your VoIP provider's gateway server. Enter the IP address or the (fully-qualified) DNS name of your SIP proxy server (maximum 74 characters). Example: myprovider.com.Proxy server portEnter the number of the communication port that the SIP proxy uses to send and receive signaling data (SIP port). Port 5060 is used by most VoIP providers.Registrar serverEnter the (fully-qualified) DNS name or the IP address of the registrar server (maximum 74 characters). The registrar is needed when the phone is registered. It assigns the public IP address/port number to your SIP address (Username@Domain) used by the phone to log in. With most VoIP providers, the registrar server is identical to the SIP server. Example: reg.myprovider.com.Registrar server portEnter the communication port used in the registrar. Usually, port 5060 is used.Registration refresh timeEnter the time intervals at which the phone should repeat the registration with the VoIP server (SIP proxy) (a request will be sent to establish a session). The repeat is required so that the entry of the phone in the tables of the SIP proxy is retained and the phone can therefore be reached. The repeat will be carried out for all activated VoIP phone numbers. The default is 180 seconds. If you enter 0 seconds, the registration will not be repeated periodically. Area: Network ExampleFor the SIP address "987654321@provider.com", enter "provider.com" in Domain.Please noteIf you have downloaded the general settings for your VoIP provider from the Gigaset configuration server (£Page 109), then some fields in this area will be preset with the data from the download (e.g. the settings for the STUN server and outbound proxy).
112Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008If your phone is connected to a router with NAT (Network Address Translation) and/or a firewall, you must select some settings in this area so that your phone can be reached from the Internet (i.e. can be addressed). Through NAT, the IP addresses of subscribers in the LAN are concealed behind the public IP address of the router.For incoming calls If port forwarding is activated or a DMZ is set up for the phone on the router, no special settings are required for incoming calls. If this is not the case, an entry in the NAT routing table (in the router) is neces-sary in order for the phone to be reached. This entry is created when the phone is registered with the SIP service. In the interest of security, this entry is auto-matically deleted at certain intervals (session timeout). The phone must there-fore confirm its registration at certain intervals (see NAT refresh time, £Page 113), so that the entry stays in the routing table. For outgoing calls The phone needs its public address to receive caller voice data. There are two possibilities: uThe phone requests the public address from a STUN server on the Internet (Simple Transversal of UDP over NAT). STUN can only be used with asymmet-ric NATs and non-blocking firewalls. uThe phone does not direct the connection request to the SIP proxy but to an outbound proxy on the Internet that supplies the data packets along with the public address. The STUN server and outbound proxy are used alternately to work around the NAT/firewall in the router. STUN enabledSelect Yes if you want your phone to use STUN as soon as it is used on a router with asymmetric NAT.STUN serverEnter the (fully-qualified) DNS name or the IP address of the STUN server on the Internet (maximum 74 characters). If you selected Yes in the STUN enabled field, you must enter a STUN server here. STUN port Enter the number of the communication port on the STUN server. The default port is 3478. STUN refresh timeEnter the time intervals at which the phone should repeat the registration with the STUN server. The repeat is required so that the entry of the phone in the tables of the STUN server is retained. The repeat will be carried out for all acti-vated VoIP phone numbers. Ask your VoIP provider for the STUN refresh time.The default is 240 seconds. If you enter 0 seconds, the registration will not be repeated periodically.
113Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008NAT refresh timeSpecify the intervals at which you want the phone to update its entry in the NAT routing table. Specify an interval in seconds that is a little shorter than the NAT session timeout. You should not need to change the preconfigured value for the NAT refresh time. Outbound proxy modeSpecify when the outbound proxy should be used.Always All signaling and voice data sent by the phone is sent to the outbound proxy. Auto Data sent by the phone is only sent to the outbound proxy when the phone is connected to a router with symmetric NAT or blocking firewall. If the phone is behind an asymmetric NAT, the STUN server is used. If you have set STUN enabled = No or have not entered a STUN server, the out-bound proxy is always used. Never The outbound proxy is not used. If you do not make an entry in the Outbound proxy field, the phone behaves independently of the selected mode, as with Never. Outbound proxyEnter the (fully qualified) DNS name or the IP address of your provider's out-bound proxy (maximum 74 characters). Outbound proxy portEnter the number of the communication port used by the outbound proxy. The default port is 5060. Saving settings on the phone ¤Select Set to save the changes.The Connections list will be shown after saving (£Figure 3 on Page 106). To discard the changes: ¤Select the Cancel button. If all fields are to be reset to the default settings:¤Select the Delete button. Fields without default settings are empty. Please noteWith many providers, the outbound proxy is identical to the SIP proxy.
114Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Activating a new connection If you have configured a new VoIP connection, you must also activate it.In the Connections list: ¤Activate the relevant option in the Active column (  = activated).Your phone will register itself with the VoIP provider using the relevant access data. Refresh the Web page (e.g. by pressing F5). The Status Registered column will appear if registration was successful. You can now be reached on this VoIP phone number. Configuring the fixed line connectionYou can assign a name to your fixed line connection. This name is used to dis-play the connection on the handset and the Web configurator interface, e.g. during allocation of send and receive numbers (£Page 120), for the call dis-play (£Page 42). ¤Open the following Web page: Settings ¢Telephony ¢Connections. ¤Select the Edit button in the Fixed Line Connection area. ¤Enter your fixed line network number or the name of your choice (maximum 16 characters) for your fixed line connection in the Connection Name or Number field. The default is "Fixed Line". Configuring the Gigaset.net connectionYour phone is assigned a Gigaset.net phone number by default. As soon as you have connected your phone to the Internet, you can make calls using the Gigaset.net and receive calls from other Gigaset.net subscribers, provided that your Gigaset.net connection has been activated. You can deactivate the Gigaset.net connection. Activating/deactivating the Gigaset.net connection¤Open the following Web page: Settings ¢Telephony ¢Connections. The list of connections is displayed (£Figure 3 on Page 106). ¤In the Gigaset.net area: use the option in the Active column to activate ( ) or deactivate ( ) the Gigaset.net connection. Please noteIf you do not make any entries for a longer period, the connection to the Web configurator is automatically terminated. Unsaved entries are lost. If neces-sary, save intermittently. You can subsequently continue the entry and make changes if necessary.Please noteOnce the new entry has been made, the VoIP phone number is assigned to each handset as a receive number. For adjusting the assignment, £Page 120.
115Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Activating/deactivating the STUN server of the Gigaset.net connectionThe Gigaset.net connection is preconfigured in your phone. The Gigaset.net uses a STUN server as standard. In the sent data packets, Gigaset.net replaces the private IP address of your phone with its public IP address. If you operate your phone behind a router with symmetrical NAT, STUN cannot be used. Otherwise, when making Gigaset.net calls you will not be able to hear the caller. In this case, deactivate STUN for the Gigaset.net connection. ¤Open the following Web page: Settings ¢Telephony ¢Connections. ¤Select Edit in the Gigaset.net area. STUN enabledClick No to deactivate STUN.Select Yes if you want your phone to use STUN. ¤Select Set to save the changes.Optimizing voice quality for VoIP connectionsYou can make general and connection-specific settings to improve the voice quality for VoIP telephony. ¤Open the following Web page: Settings ¢Telephony ¢Audio. The voice quality for VoIP connections is mainly determined by the voice codec used for transferring the data and the available bandwidth of your DSL con-nection. In the case of the voice codec, the voice data is digitalized (coded/decoded) and compressed. A "better" codec (better voice quality) means more data needs to be transferred, i.e. perfect voice data transfer requires a DSL connection with a larger bandwidth. The following voice codecs are supported by your phone:G.722 Excellent voice quality. The broadband speech codec G.722 works at the same bit rate as G.711 (64 kbit/s per speech connection) but with a higher sampling rate. This allows higher frequencies to be played back. The speech tone is there-fore clearer and better than for the other codecs (High Definition Sound Per-formance). Gigaset S67H, S68H and SL37H are examples of HDSP-compatible handsets. Please noteIf you do not use your Gigaset.net connection for six weeks, it is automatically deactivated. You cannot be reached for calls from Gigaset.net. The connection is reactivated:uAs soon as you start a search in the Gigaset.net directory (£Page 48) or uMake a call via Gigaset.net, i.e. dial a number ending in #9 (two attempts may be necessary) or uActivate the connection via the Web configurator as described above.
116Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008G.711 a law / G.711 µ law Excellent voice quality (comparable with ISDN). The necessary bandwidth is 64 kbit/s per voice connection. G.726 Good voice quality (inferior to that with G.711 but better than with G.729). Your phone supports G726 with a transmission rate of 32 kbit/s per voice con-nection. G.729 Average voice quality. The necessary bandwidth is less than or equal to 8 kbit/s per voice connection. Both parties involved in the telephone connection (caller/sender and recipient side) must use the same voice codec. The voice codec is negotiated between the sender and the recipient when establishing a connection. You can influence the voice quality by selecting (bearing in mind the band-width of your DSL connection) the voice codecs your phone is to use, and spec-ifying the order in which the codecs are to be suggested when a VoIP connec-tion is established. Area: Settings for BandwidthThe settings in this area influence all VoIP connections (VoIP phone numbers). Allow 1 VoIP call onlyYou can usually make two VoIP calls at the same time on your phone. If, how-ever, your DSL connection has a narrow bandwidth, there may be problems if two VoIP calls are made at the same time. The data is no longer transferred properly (long voice delay, data losses, etc.). ¤Select Yes after Allow 1 VoIP call only to prevent any further parallel VoIP phone connections being established. ¤If you wish to permit two VoIP connections, select No.Voice QualityDefault settings for the codecs used are stored in your phone: one setting opti-mized for narrow and one for wide bandwidths. ¤Activate one of the options Optimized for low bandwidth / Optimized for high bandwidth if you wish to accept a default setting for all VoIP connections. The settings are shown in the Settings for Connections area and cannot be changed. ¤Activate the Own Codec preference option if you wish to select and set connec-tion-specific voice codecs yourself ( ¢"Area: Settings for Connections"). Please note If only one VoIP connection is permitted, the following VoIP network services will no longer be available:uCall waiting is not displayed during a call via VoIP. uExternal consultation call from a VoIP call uToggling and initiating a conference call via VoIP
117Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Area: Settings for ConnectionsIn this area you can make specific settings for each of your VoIP phone num-bers. You can make the following settings for each VoIP phone number configured on your phone:Volume for VoIP CallsDepending on the VoIP provider, it is possible that the received voice/earpiece volume is too low or too high, so that adjusting the volume via the handset is not adequate. Specify whether the received volume range is too high or too low. The follow-ing options are available: Low Voice/earpiece volume is too high. Activate this option to reduce the volume by 6 dB. Normal The voice/earpiece volume does not need to be raised/lowered. High Voice/earpiece volume is too low. Activate this option to increase the vol-ume by 6 dB. Voice codecsPrerequisite: The Own Codec preference option is activated for the Voice Quality in the Settings for Bandwidth area.Select the voice codecs your phone is to use, and specify the order in which the codecs are to be suggested when a VoIP connection is established via this VoIP phone number. ¤Apply the voice codecs that your phone is to suggest for outgoing calls into the Selected codecs list. To do this, in the Available codecs list select the voice codec that you want to apply (you can mark several entries using the Shift key or the Ctrl key). Select <Add. ¤Move the voice codecs that you do not want the phone to use into the Available codecs list.Select the voice codecs in the Selected codecs list (see above) and click the Remove> button. ¤Sort the voice codecs in the Selected codecs list into the order in which they should be suggested to the receiving device when a connection is estab-lished. To do this, use the Up and Down buttons. When establishing a VoIP connection, the phone suggests the 1st voice codec in the Selected codecs list to the receiving device to begin with. If the receiving device does not accept this voice codec (e.g. because it is not supported), the 2nd voice codec on the list is suggested, and so on. If the receiving device does not accept any of the voice codecs in the Selected codecs list, the connection is not established. An appropriate message is dis-played on the handset.
118Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008If the phone always starts by trying to establish a broadband connection, put the G.722 codec at the top of the Selected codecs list. Area: Settings for CodecsTo save additional bandwidth and transmission capacity, on VoIP connections that use the G.729 codec you can suppress the transmission of voice packets in pauses ("Silence Suppression"). Then, instead of the background noises in your environment, your caller hears a synthetic noise generated in the receiver.Please note: "Silence Suppression" can sometimes lead to deterioration in the voice quality. ¤In the Enable Annex B for codec G.729 field, state whether the transmission of data packets during pauses should be suppressed when using the G.729 codec, (select Yes). Saving settings on the phone ¤Select Set to save the settings for the voice quality.Voice quality and infrastructure With your Gigaset A580 IP, you have the opportunity to make calls with good voice quality via VoIP. However, your phone's performance with VoIP – and therefore the voice quality – also depends on the properties of the entire infrastructure. The following VoIP provider components are just some of the things that can impact performance:uRouteruDSLAM uDSL transmission line and speeduConnection paths over the Internet uIf applicable, other applications that also use the DSL connectionPlease noteuOnly deactivate codecs (put them in the Available codecs list) if there is a par-ticular reason. The more codecs that are deactivated increases the risk of calls not being established due to unsuccessful codec negotiations. In par-ticular you can only establish broadband connections if you permit the G.722 codec. uWith incoming calls, all supported voice codecs are always permitted. Please notePlease observe the following for good voice quality:uWhen making calls using VoIP, avoid performing other Internet activities (e.g. surfing the Internet). uPlease note that voice delays can occur depending on the codec used and the network capacity utilization.
119Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008In VoIP networks, voice quality is affected by various things including the "Qual-ity of Service" (QoS). If the entire infrastructure demonstrates QoS, voice qual-ity is higher (fewer delays, less echoing, less crackling, etc.). If, for example, the router does not have QoS, then the voice quality is not as good. Please see the specialist documentation for further information. Setting the telephone's default connectionThe default telephone connection defines which line type (VoIP or fixed line network) will be used to dial numbers when you briefly press the c Talk key. The default connection is applied to all registered handsets. ¤Open the following Web page: Settings ¢Telephony ¢Number Assignment. Area Default Connection¤Select the default connection for your phone. This can be done by selecting option VoIP or Fixed Line after Linetype for outgoing calls. ¤Select Set to activate your settings.Activating the fixed line network connection as an alternate connectionYou can activate the fixed line network connection on your phone as an alter-nate connection. If an attempt to establish a connection via VoIP then fails, an attempt is made automatically to establish the connection via the fixed line network. An alternate connection would be used in the following cases:uYour VoIP connections are busy.uThe SIP server for the VoIP connection cannot be accessed.uThe dialed VoIP connection has not (yet) been configured correctly (e.g. incorrect password).uThe base station does not have a connection to the Internet, e.g. because your router is deactivated or not connected to the Internet.¤Open the following Web page: Settings ¢Telephony ¢Number Assignment. Please noteuThe default connection is only relevant when dialing numbers that are not subject to dialing plans and are entered without a line suffix. uYou can change the settings for the default connection via any registered handset (£Page 86).ExceptionsIf a URI or IP address is dialed instead of a phone number, the connection can-not be created via the fixed line network.
120Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Area Default Connection¤To activate the fixed line network connection as an alternate connection, click the Yes option next to Automatic Fallback to Fixed Line. Select No to deac-tivate the function. ¤Select Set to activate your settings.Assigning send and receive numbers to handsetsYou can assign up to eight phone numbers on your phone: your fixed line net-work number, your Gigaset.net number and six VoIP numbers. You can assign as many of these numbers as you like to each handset as receive numbers. Receive numbers determine which handset(s) will ring when a call is received.You can assign one of your VoIP numbers to each handset as a (VoIP) send number. Send numbers define which VoIP account should be used generally to make and pay for outgoing VoIP calls. Exceptions: uA phone number is dialed with a line suffix (£Page 107) or uA dialing plan has been defined for the phone number (£Page 123). The Gigaset.net number and fixed line network number are permanently assigned to each registered handset as send numbers. ¤Open the following Web page: Settings ¢Telephony ¢Number Assignment.The display shows all registered handsets. A list is displayed for each handset showing the phone numbers that are configured and activated for the phone. The connection names are shown in the column Connections. The fixed line net-work connection is always at the end of the list.¤Define a VoIP phone number as the send number for each handset. To do this, click the option following the phone number in the for outgoing calls col-umn. The previous assignment will automatically be deactivated. Please noteA handset is assigned the following numbers after it is registered on the base station:uReceive numbers: all phone numbers assigned to the phone (fixed line net-work, Gigaset.net and VoIP). uSend numbers: the fixed line network number and the VoIP phone number that you entered at the start of the phone configuration.Please noteThe fixed line network number is permanently assigned to each handset as a send number. This assignment cannot be deactivated. It ensures that emer-gency numbers can be called from every handset. The Gigaset.net number is also permanently assigned to each handset.
121Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008¤Select the phone numbers for each handset (fixed line network, VoIP) that are to be assigned to the handset as receive numbers. To do this, click the option following the phone number in the for incoming calls column. Every handset can be assigned several phone numbers or no phone number (=assigned).¤Select Set to save your settings.Activating Call Forwarding for VoIP connectionsYou can forward calls to your VoIP numbers and to your Gigaset.net number. You can forward calls to your VoIP numbers to any external number (VoIP, fixed line or mobile network number). The forwarding is done via a VoIP connection. You can forward calls to your Gigaset.net number within the Gigaset.net, i.e. to another Gigaset.net number. You can define if and when calls to your Gigaset.net number and some of your VoIP numbers (VoIP account) should be forwarded to this VoIP number. You can also use the handset to set and activate/deactivate call forwarding, £Page 53. ¤Open the following Web page: Settings ¢Telephony ¢Call Forwarding.The display shows a list of all your configured VoIP connections and your Gigaset.net number. ConnectionsSelect the name you have assigned to the VoIP number, or select Gigaset.net. When Select when a call to this VoIP number should be forwarded: When busy / No reply / Always. Select Off to deactivate call forwarding. Call number Enter the phone number to which the calls should be forwarded. Please note that you may have to enter the area code when forwarding to a fixed line network number in the same area (depending on your VoIP provider and the setting for the automatic area code £Page 122). The settings only affect the phone number selected in Connections. Please noteuIf a VoIP phone number that has been assigned to a handset as a send number is deleted, the handset will automatically be assigned the first con-figured VoIP phone number. uCalls made to a number that is not assigned to a handset as a receive number will not be signaled on any handset. uIf you have not assigned receive numbers to any of the handsets, calls to all connections will be signaled on all handsets.
122Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Entering your own area code, activating/deactivating an automaticarea code for VoIPOn the base station, save the complete code (with international code) for the area in which you are using the phone. For VoIP calls you must generally always dial the area code – even for local calls. You can save the need to dial the area code for local calls by setting your phone to prefix this code for all VoIP calls made in the same local area ( £Predial area code for local calls through VoIP option). For calls made via VoIP, the area code entered is then prefixed to all numbers that do not start with 0 – even when dialing numbers from the directory and other lists. Exceptions: Phone numbers for which you have defined dialing plans and deactivated the Use Area Codes option (£Page 123). When making calls via the fixed line network, the area code entered is with-held, e.g. when dialing using the Calls list (£Page 61). ¤Open the following Web page: Settings ¢Telephony ¢Dialling Plans.Area Area CodesMake the following settings here:¤From the Country list, select the country in which you are using your phone. This way the country code and the prefix of the area code are automatically set (in International Prefix / Area Code and Local Prefix fields). ¤In the Local Area Code field, enter the area code for your town/city without a prefix (maximum 8 characters 0–9, *, #, R, P, r, p), e.g. 617 (for Boston). ¤Select Yes next to Predial area code for local calls through VoIP to activate the function. Select No to deactivate the function. You will then need to enter the area code for local calls made via VoIP. Numbers in the directory must always contain the area code when dialing via VoIP.¤Select Set to save the settings.Please noteFor information on entering your area code via the handset, £Page 87.Please note uThe area code will also be prefixed to VoIP calls made to emergency numbers if there are no defined dialing plans for these numbers. uThe numbers of your network mailbox saved in the base station are not prefixed with an area code (£Page 125).
123Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Defining dialing plans – cost controlYou can define dialing plans to reduce costs:uYou can define the connection (one of your VoIP accounts, the fixed line network) through which calls to specific numbers should be made and paid for. If you enter just a few digits (e.g. local area, national or cellular network code) any call to a number beginning with these digits will be made via the elected connection. uYou can block specific numbers, i.e. your phone will not establish a connec-tion to these numbers (e.g. 1900 numbers). These dialing plans apply to all registered handsets. The settings for the default connection (briefly press/press and hold c) and the send numbers of hand-sets do not apply to numbers governed by a dialing plan. Tips: uCompare the rates for long-distance calls (especially for international calls) offered by your fixed line network and VoIP providers, and determine which connection should be used specifically for these countries/locations, e.g. a dialing plan for the Phone Number "01133" would apply to every call made to France.uUse dialing plans to define that numbers starting with a call-by-call number are always made via your fixed line network connection. To do so, enter the call-by-call number in the Phone Number field. Defining dialing plans¤Open the following Web page: Settings ¢Telephony ¢Dialling Plans.Area Dialling PlansSpecify dialing plans for your phone. Specify the following: Phone NumberEnter the number or the first digits of the phone number (e.g. an area code) to which the dialing plan should apply (maximum 15 digits).Use Area CodesActivate this option if the area code is to be added automatically for all calls via VoIP for the phone number in Phone Number or all phone numbers that begin with the digits in Phone Number (£Page 122). Please noteYou can override dialing plans, with the exception of blocks, as follows: uDial the number with a line suffix (e.g. 123456789#3, £Page 38). uBefore entering the number, define another connection type by pressing the §Phone§ or §IP§ Display key (£Page 79). If, for example, you press §Phone§, the number will be dialed via the fixed line network, even if the dialing plan states that a VoIP connection should be used.
124Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Connection TypeThe list shows all the VoIP connections that you have configured as well as your fixed line network connection. It also displays the name assigned to each con-nection. ¤From the list, select the connection via which the number or numbers that start with the specified sequence of digits should be dialed. Or: ¤Select Block if the number or numbers that start with the sequence of digits should be blocked. The display will show Not possible! if an attempt is made to dial a blocked number. Comment (optional) You can enter a description of the dialing plan here (maximum of 20 charac-ters). ¤Select Add.The dialing plan is activated immediately. A new empty line for a new dialing plan will appear if your phone still has enough space to add further plans. Activating/deactivating dialing plans¤Select the option in the Active column to activate/deactivate the correspond-ing dialing plan (  = activated). A deactivated dialing plan will not take effect until it is reactivated. Please noteIf dialing plans overlap, the one with the greatest concordance will apply. Example:There is a dialing plan for the number "21" and one for the number "217". If you dial "2171..." the second plan will apply; if you dial "2101..." the first plan will apply. ExampleuYou want to block your phone for all 1900 numbers. Dialing plan: Phone Number = 0190 Connection Type =Block uAll calls to the cellular phone network should be made via your VoIP connec-tion with provider B.Dialing plans: Phone Number = 020 Connection Type =IP3,providerBand the corresponding entries for "030" and "040", etc.
125Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Deleting dialing plans¤Select Delete next to the dialing plan you wish to delete.The dialing plan is deleted from the list immediately. The space in the list is released. Emergency numbersDialing plans for emergency numbers (e.g. the local emergency service number) are preset for certain countries. The fixed line network is determined as the Connection Type. These dialing plans cannot be deleted, deactivated or blocked. However, you can change the Connection Type.This should only be changed if the phone is not connected to the fixed line network. If you choose a VoIP connection, please make sure the VoIP provider supports calls to emergency numbers. If no emergency numbers are set by default, define dialing plans for emergency numbers yourself and assign them to a connection that you know supports emergency calls. Deactivate the Use Area Codes option for these dialing plans. Calls to emergency numbers are always supported by fixed line networks. Activating/deactivating network mailbox, entering numbers Many fixed network providers and VoIP providers offer answer machines on the network – these are known as network mailboxes. Each network mailbox accepts incoming calls made via the corresponding line (fixed line network or corresponding VoIP phone number). You can enter the relevant network mailbox for each configured connection (VoIP, fixed line network) via the Web configurator. You can activate or deacti-vate the network mailbox for your VoIP connections. ¤Open the following Web page: Settings ¢Telephony ¢Network Mailbox.A list with all possible connections is displayed on the Web page. The names of the connections are displayed in the Connection column. Please notePredefined dialing plans set as defaults (for emergency numbers) cannot be deactivated and cannot be deleted. WarninguEmergency numbers cannot be dialed if the keypad lock is activated. Before dialing, press and hold the Pound key #, to release the keypad lock. uIf you have activated an automatic area code (£Page 122) and if no dialing plan for emergency numbers is defined, the area code will also be prefixed to emergency calls made via VoIP.
126Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Entering numbers¤Enter the network mailbox number in the Call number column after the desired connection. With some VoIP providers your mailbox number will be downloaded together with the general VoIP provider data (£Page 109), saved to your base station and displayed under Call number. ¤Select Set to save your settings.Activating/deactivating the network mailbox¤You can activate ( ) and deactivate ( ) individual network mailboxes using the option in the Active column. Activating/deactivating is carried out by selecting the appropriate option. The change does not need to be saved.Setting DTMF signaling for VoIPDTMF signaling, for example, is required to check and control some network mailboxes via digit codes. To send DTMF signals via VoIP you must first define how key codes should be converted into and sent as DTMF signals: as audible information via the speech channel or as a "SIP Info" message. Ask your VoIP provider which type of DTMF transmission it supports. ¤Open the following Web page: Settings ¢Telephony ¢Advanced Settings.Area DTMF over VoIP connectionsMake the required settings for sending DTMF signals. ¤Activate Audio or RFC 2833, if DTMF signals are to be transmitted acoustically (in voice packets).¤Activate SIP Info if DTMF signals are to be transmitted as code. ¤Select Set to save your settings.‰Please noteYou need to have requested the network mailbox for your fixed line network connection from your fixed line network provider. Please noteuThe settings for DTMF signaling apply to all VoIP connections (VoIP accounts). uDTMF signals cannot be transmitted in the audio path (Audio) on broadband connections (the G.722 codec is used).
127Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Defining Flash key functions for VoIP (hook flash)Your VoIP provider may support special performance features. To make use of these features, your phone needs to send a specific signal (data packet) to the SIP server. You can assign this "signal" to your phone's Flash key. If you press the Flash key during a VoIP call the signal will be sent to the server. Prerequisite: uDTMF reminders via SIP info messages is activated, i.e. the option SIP Info on this Web page is activated (£Page 126).uThe S key is not used for call forwarding, i.e. Use the R key to initiate call transfer with the SIP Refer method. = No is set for call forwarding (£Page 127).If one of these prerequisites is not fulfilled, the field in the Hook Flash (R-key) area is hidden. ¤Open the following Web page: Settings ¢Telephony ¢Advanced Settings.Area Hook Flash (R-key)¤In the Application Type fields, (maximum 31 characters) and Application Signal fields (maximum 15 characters) enter the data that you have received from your VoIP provider. ¤Select Set to save your settings.The setting for the Flash key applies to all registered handsets.Configuring call forwarding via VoIP If you are toggling calls via VoIP connections, you can connect the two external callers (provider-dependent). You can configure settings for this type of call for-warding.¤Open the following Web page: Settings ¢Telephony ¢Advanced Settings.Area Call Transfer¤Make your settings for call forwarding via VoIP in the following fields: Use the R key to initiate call transfer with the SIP Refer method.If you activate the Yes option, the two external parties you are toggling between will be connected when you press the End Call key S. Your connec-tions with the callers will be terminated. Transfer Call by On-HookIf you select Yes, the external parties you are toggling between will be con-nected when you press the End Call key a. Your connections with the callers will be terminated.
128Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Preferred Refer ToDefine the protocol (the contents of the "Refer To" information) that should be used with preference when forwarding calls:Target’s contact info This protocol is recommended for "closed" networks (internal company and business networks).Original URL This protocol is recommended when the base station is connected to the Internet via a router with NAT. Automatic Refer ToIf you select Yes, the base station will automatically attempt to determine the best protocol. If the base station cannot determine the best protocol, it will use the protocol defined in Preferred Refer To. ¤Select Set to save your settings.Defining local communication ports for VoIPSpecify which local communication ports (port numbers) the telephone is to use for VoIP telephony. The ports must not be used by any other subscriber in the LAN. The following communication ports are used for VoIP telephony:uSIP portCommunication port via which the phone receives (SIP) signaling data.uRTP portTwo consecutive RTP ports (consecutive port numbers) are required for each VoiP connection. Voice data is received via one port and control data via the other.You can set port numbers or port number areas for SIP and RTP ports, or set your telephone so that it can use any number of free ports from a predefined range of port numbers. ¤Open the following Web page: Settings ¢Telephony ¢Advanced Settings.Please noteFor information on forwarding a call when you deactivate both Use the R key to initiate call transfer with the SIP Refer method. and Transfer Call by On-Hook, £Page 56.
129Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Area Listen ports for VoIP connectionsUse random portsClick No if you want the phone to use the ports specified in the fields SIP port and RTP port.Click Yes if you do not want the phone to use fixed ports for SIP port and RTP port, but rather to use any free ports from predefined ranges of port numbers. The use of random ports makes sense if you want several phones to be oper-ated on the same router with NAT. The phones must then use different ports so that the router's NAT is only able to forward incoming calls and voice data to one (the intended) phone. Use random ports =NoSIP port Specify the port number for the SIP port. Enter a number between 1024 and 49152 in the field. The default port number for SIP signaling is 5060. The port number specified must not be in the RTP port number range. RTP port Specify a range of port numbers that are to be used as RTP ports. This range must be used in the LAN (router) for the phone. Enter the lowest port number in the left-hand field and the highest number in the right-hand field (numbers between 1024 and 55000). Size of the port number range: The difference between the port numbers must be at least 6 if you permit two simultaneous VoIP calls on your phone. The difference must be at least 4 if you only permit one VoIP call ( ¢Allow 1 VoIP call only option on Page 116).The lower of the port numbers in the range (in the left-hand field) must be an even number. If you enter an odd number, the next lower even number will be selected automatically (e.g. if you enter 5003, then 5002 is set automatically).The default port number for voice transmission is 5004. Use random ports =Yes SIP port Enter the port number range from which the SIP port is to be selected. Specify the lowest port number in the left-hand field and the highest number in the right-hand field (number between 1024 and 49152). This port number range must not overlap the range specified for RTP port. The default range is 5060 to 5076. RTP port Specify a range of port numbers from which the RTP ports are to be selected. Specify the lowest port number in the range in the left-hand field and the high-est number in the right-hand field. The default range is 5004 to 5020. ¤Select Set to save your settings.
130Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008MessagingYour Gigaset A580 IP base station has messaging functions that can be used via a messaging capable handset, e.g. a Gigaset S67H, S68H, SL37H or C47H hand-set, which you can register to your base station. The following messaging functions are available: uMessenger functionsThe messenger client in your base station enables instant messaging (immediate message transfer, chatting). The phone supports the XMPP mes-senger (Jabber).uE-mail functions Your phone checks at regular intervals whether new e-mail messages have arrived in your incoming e-mail server. New e-mail messages are displayed on a messaging-capable handset in the form of e-mail notifications (e-mail sender and subject). You can read approximately the first 500 to 600 char-acters of a text e-mail on the handset. Saving messenger access dataTo use your base station's messenger functions, you need to register a handset with messaging capability and save the access data for your message server in the phone.Your base station is already registered with the Gigaset.net Jabber server. An account has been assigned to your phone. You can chat to other Gigaset.net subscribers via this account. To do this, you need to log on to the Gigaset.net message server via your PC's Web browser using only this account, and then create a Buddy list ( £ "Setting up a Gigaset.net Jabber account", Page 131). You can also register with another instant messaging provider that supports XMPP Messenger (Jabber). In order for you to use your phone's messenger to "go online" and "chat" on the Internet, the access data of a message server must be saved on your phone. You can define a Resource name and a Priority for your phone. Both are required if you are logged in (online) with the message server with several devices (phone, desktop PC and laptop) at the same time using the same Jabber ID. The Resource name is used to distinguish between these devices. The phone cannot log in to the message server if it does not have a resource name. Assign a Priority as each message will only be sent to one device for each Jabber ID. The Priority determines which of the devices receives the message. ¤Open the following Web page: Settings ¢Messaging ¢Messenger. ExampleYou are online using one of your phone's handsets and your PC both at the same time. You have assigned your phone (Resource name "phone") Priority 5 and your PC (Resource name "PC") priority 10. In this case, any message addressed to your Jabber ID will be sent to your phone.
131Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008¤In the Messenger Account field, select whether you wish to use the Gigaset.net Jabber server or another provider's message server (Other). The access data for Gigaset.net is already stored in the base station. It is dis-played in Jabber ID, Authentication password and Jabber server. With this data you can also register with the Gigaset.net Jabber server through your PC. ¤Enter the user ID (maximum 50 characters) and password (maximum 20 characters) that you used to register with the message server in the Jab-ber ID and Authentication password fields. If you have selected = Messenger Account Gigaset.net, the fields are preset with your Gigaset.net account. ¤In the Jabber server field, enter the IP address or the DNS name of the mes-sage server with which you are registered for instant messaging.Max. 74 alphanumeric characters.If you have selected Messenger Account = Gigaset.net, the field is preconfig-ured with the name of the Gigaset.net server. ¤Enter the number of the communication port on the Jabber server in the Jabber server port field. The default port is 5222. If you have selected Messenger Account = Gigaset.net, the port number is pre-configured. ¤Enter a resource name (maximum 20 characters) in the Resource field. The default is phone.¤Enter the priority for your phone in the Priority field. Select a number between -128 (highest priority) and 127 (lowest priority) for the priority. The default is: 5¤Select Set.Setting up a Gigaset.net Jabber accountYour phone is already registered with the Gigaset.net Jabber server. An account has been assigned to your phone. To chat with other Gigaset.net subscribers via this account, you must transfer the required Gigaset.net subscribers to a Contact list (Buddy list) on your PC. You can use any conventional Jabber client for this (e.g. PSI, Miranda; see e.g. http://www.swissjabber.ch).Do the following to use your Gigaset.net Jabber account:¤Start the Web configurator, open the Settings ¢Messaging ¢Messenger Web page and select the Messenger Account Gigaset.net field. Your account data is displayed in Jabber ID and Authentication password. You will need these to create a Buddy list via the Jabber client on the PC.¤Start your Jabber client on the PC.¤Enter your Gigaset.net Jabber ID on the Jabber client as a new account. The Jabber ID consists of your Gigaset.net number and "@jabber.gigaset.net"Example: 12345678901#9@jabber.gigaset.net ¤Then enter your Authentication password.
132Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008¤Now you can enter Gigaset.net subscribers as contacts (buddies). For the Jabber ID of each subscriber, enter the subscriber's Gigaset.net number with "@jabber.gigaset.net" (example: 2141524901#9@jab-ber.gigaset.net).A request to "Add to Contact list" will be sent to the subscriber.If the subscriber accepts this request, they will be added to your Buddy list. Configuring incoming e-mailYou must store the address or DNS name of your incoming e-mail server and your personal access data in the phone and activate the e-mail check with the incoming e-mail server, so that the phone can establish a connection to the incoming e-mail server and connect to your mailbox. ¤Open the following Web page: Settings ¢Messaging ¢E-Mail. ¤Enter the user name (account name) agreed with the Internet provider (maximum 74 characters) in the Authentication Name field. ¤Enter the password agreed with the provider for accessing the incoming e-mail server (maximum 32 characters; case sensitive) in the Authentication password field. ¤Enter the name of the incoming e-mail server (POP3 server) (maximum 74 characters) in the POP3 Server field. Example: pop.theserver.com.¤Select from the Check for new e-mail list the time interval at which your phone should check whether new messages have arrived in your incoming e-mail server. Select Never to deactivate the request. Select one of the other values to activate the prompt for new e-mail messages. ¤Select the Set button to save the settings in your phone. Please noteuDo not select the option "Create new account". Your Gigaset.net Jabber account has already been created in Gigaset.net.uThe option "SSL connection" must be deactivated in the Jabber client.Please noteFor information on going online with your messaging-capable handset and chat with or call buddies, please see the extensive user guides for the Gigaset S675 IP or C470 IP for example. These are available on the Internet at:www.gigaset.comPlease noteFor information on how e-mail messages are displayed and opened on the messaging-capable handset, please see the extensive user guides for the Gigaset S675 IP or C470 IP for example. These are available on the Internet at:www.gigaset.com
133Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Configuring info services/activating idle displayYou can configure your registered Gigaset A58H handsets to display custom-ized text information (e.g. weather reports, RSS feeds) in the idle display. To do this you must set the Info Services screensaver on the handset (£Page 78). The same applies to a registered Gigaset C38H handset. Configuring info services¤Open the following Web page: Settings ¢Services. ¤Click the link in the Info Services Configuration area.www.gigaset.net/myaccount or enter the URL into the address field of a different browser window. The Web page for Gigaset.net info services is opened. You are now regis-tered with your Gigaset.net user ID. Your Gigaset.net user ID and password are displayed in the Info Services Configuration area of the Web configurator Services page. This will open a website where you can compile your info service. ¤Define which information should be sent regularly to your handset. Activating the display of info services for Gigaset S67H, S68H, SL37H and C47H handsetsYou can also display the selected text information on a Gigaset S67H, S68H, SL37H or C47H handset that is registered to your base station. If one of these handsets is registered to your base station the Activate Info Serv-ices area in which you can activate the display for these handsets is displayed on the Services Web page. ¤Open the following Web page: Settings ¢Services. ¤In the Activate Info Services area, activate Yes /No to activate or deactivate the display of text information. ¤Select the Set button to save the settings in your phone. If text information is available it is displayed (in idle display) on all registered Gigaset S67H, S68H, SL37H or C47H handsets for which the digital clock is set as the screensaver. The text information overwrites the digital clock. Changing internal handset numbers and namesEach handset is automatically assigned an internal number (1 to 6) and an internal name ("INT 1", "INT 2", etc.) when it registers with the base station (£Page 71). The internal numbers and names of all registered handsets can be changed. Please noteThe weather report is preset. It is shown in the handset's idle display as soon as you set the Info Services as the screensaver.
134Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008¤Open the following Web page: Settings ¢Handsets.The names and internal numbers of all registered handsets are displayed in the Registered Handsets area. ¤Select the handset whose number/name you want to change. ¤Changing numbers: Select the internal number that you want to assign to the handset in the No. column of the handset. If a handset with this internal number already exists, you will also have to change the number assigned for this handset. The internal numbers 1-6 can only be assigned once each.¤Changing names: If necessary, change the name of the handset in the Name column. The name may contain up to 10 characters. ¤If necessary, repeat the process for other handsets. ¤Select Set to save the settings. The changes are saved in the internal lists of all registered handsets. Handsets are sorted by their internal numbers in the internal list. The order of the hand-sets in the list can be changed. Transferring handset directories to/from the PCThe Web configurator has the following options for editing the directories of the registered handsets. uStore the handset directories on a PC. Entries are stored in vCard format in a vcf file on the PC. You can edit these files with an ASCII editor (e.g. Notepad/Editor in Windows Accessories) and load them onto any registered handset. You can also transfer directory entries to your PC address book (e.g. Outlook Express™ address book). uTransfer contact details from your PC address book to handset directories. Export the contacts, e.g. with Outlook Express ™ to vcf files (vCards) and transfer them to handset directories using the Web configurator. uDelete the directory on the handset. If you have edited the directory file (vcf file) on the PC and would like to use this modified directory on the handset, you can delete the current directory from the handset first. Tip: Back up the current directory on your PC before deleting it. You can then reload it onto the handset if the modified directory is affected by formatting errors and some, or all, of it cannot be loaded onto the handset. Please noteFor information on changing internal names and numbers, £Page 73. Please noteIf an internal number has been entered twice, a message will appear. The internal numbers are not changed.
135Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Prerequisites: uThe handset can send and receive directory entries. uThe handset is activated and is in idle status. ¤Open the following Web page: Settings ¢Handsets.The names of all registered handsets are displayed in the Directory area. ¤Select the handset for which you want to save or edit the directory. To do this, click on the option before the handset. Loading the directory file from the PC to the handset¤In the Transfer directory to handset area, specify the vcf file you want to load on to the handset (complete path name), or select Browse... and navigate your way to the file.¤Select Transfer button to start the transfer.The display will show how many of the entries from the vcf file are being trans-ferred to the directory. Transfer rulesThe directory entries from a vcf file that are loaded onto the handset will be added to the directory. If an entry already exists for a name, it will either be sup-plemented or a new entry for the name will be created. The process will not overwrite or delete any phone numbers. Loading the directory from the handset to the PC¤Select Save in the Handset Directory area. A Windows dialog box will be shown to save the file. ¤Enter the directory on the PC (complete path name) in which the directory file is to be stored. Select Save or OK. Please noteuYou can find information on the vCard format (vcf) on the Internet, e.g. at: www.en.wikipedia.org/wiki/VCard or www.de.wikipedia.org/wiki/VCard (You can set the display language at the bottom left-hand side in the navi-gation area of the Web page.)uTo transfer a handset directory (vcf file) saved on the PC that contains numerous entries to a Microsoft Outlook™ address book, be aware that Microsoft Outlook™ only transfers the first (directory) entry from the vcf file to its address book. Please noteDepending on your handset type, up to three entries with the same name will be created in the handset directory for each vCard – one entry per entered number.
136Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Deleting the directory¤Select Delete in the Handset Directory area. ¤Confirm the security prompt Telephone directory of the selected handset will be deleted. Continue? with OK. This deletes all the entries in the directory,. Directory file content (vcf file)The following data (if available) is written into the vcf file for entry into the directory or transferred from a vcf file into the handset directory.§§1§§ Name§§2§§ First name§§3§§ Number§§4§§ Number (office)§§5§§ Number (cell)§§6§§ E-mail address §§7§§ Date (YYYY-MM-DD) and time of the reminder call (HH:MM) separated by a "T" (example: 2008-01-12T11:00).§§8§§ Identification as VIP (X-SIEMENS-VIP:1)Other information that a vCard may contain is not entered into the handset directory.Example for an entry in vCard format:BEGIN:VCARDVERSION:2.1N:Smith;AnnaTEL;HOME:1234567890TEL;WORK:0299123456TEL;CELL:0175987654321EMAIL:anna@smith.comBDAY:2008-01-12T11:00X-SIEMENS-VIP:1END:VCARDActivating VoIP status message displayYou can display VoIP status messages on your handset when there are VoIP con-nection problems. These messages give you information on the status of a con-nection and contain a provider-specific status code that helps the service team when they are analyzing the problem. ¤Open the following Web page: Settings ¢Handsets. Please noteFor deleting the directory on the handset, £Page 64.
137Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Area VoIP Status ¤Select Yes after Show VoIP status on handset to activate the status message dis-play.If you select No, no VoIP status messages are displayed. ¤Select Set to save the changes. Starting a firmware updateIf necessary, you can load updates of the base station firmware onto your phone. The server on which Gigaset Communications makes new firmware versions available for your base station is set by default. The URL of the Internet server is displayed in the Data server field. Only change this URL when requested by Customer Care. This address is also used to load provider information from the Internet. Make sure you write down the default URL exactly before changing it. Otherwise, you will only be able to reactivate the default URL by resetting the base station back to the default settings (£Page 85).Prerequisites:uNo calls are being made via the fixed line network or VoIP.uThere is no internal connection between registered handsets or to GHC devices. uThe base station menu is not open in any of the handsets. ¤Open the following Web page: Settings ¢Miscellaneous. ¤Select the Update Firmware button.The firmware is updated. This process can take up to three minutes.Please noteThis user guide contains a table with possible status codes and their defini-tions, £Page 145.Please noteuWhen updating from the Internet, checks are made to ensure that no newer version of the firmware exists. If this is not the case, the operation is terminated.uThe firmware is only loaded from the Internet if you have not entered a local file in the User defined firmware file field prior to the update. Please noteYou can also start the firmware update on the handset (£Page 87).
138Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Firmware update from local firmware file In extraordinary circumstances you may receive, for example, a firmware file from Service that you can upload from your PC to your telephone (e.g. because the firmware update via the Internet did not work). Prerequisite: A Web server is running on the local PC (e.g. Apache).¤First load the firmware file onto your PC. ¤In the User defined firmware file field enter the IP address of the PC in your local network and the complete path and name of the firmware file on the PC (maximum 74 characters). Example: 192.168.2.105/A580IP/FW_file.bin.¤Select Set to save the changes. ¤Select the Update Firmware button to start the update.This setting is automatically used for this particular firmware update. The URL in the Data server field is saved and used again for subsequent firmware updates. You will have to re-enter the IP address and file name to carry out another update with a firmware file on your local PC.Activating/deactivating the automatic version checkWhen the version check is activated, the phone checks on a daily basis whether the Gigaset configuration server has a new version of the phone firmware/pro-vider profile (general provider data).If a new version is available, a notification is sent to the handset and the Message key flashes. You can then perfom an automatic update of the firmware (£Page 88) or carries out a provider data update. ¤Open the following Web page: Settings ¢Miscellaneous. ¤Select Yes next to Automatic check for software/profile updates to activate the automatic version check.Select No if you do not want a version check to be carried out. ¤Select Set to save the changes. Please noteIf an error occurs during a firmware update from a local PC, the most recent version of the firmware is automatically downloaded from the Internet.Please noteIf the telephone is not connected to the Internet at the time when the check for new firmware is to be carried out (e.g. because the router is deactivated), the check is carried out as soon as the phone is reconnected to the Internet.
139Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Copying the date/time from time serverThe date and time are shown in the idle display of registered handsets. They are important, for example, for stating the correct time in the Calls list and for the "alarm clock" function. There are two methods for updating the time and date on your base station: manually with one of the registered handsets (£Page 14) or automatically by synchronization with a time server on the Internet.Activate/deactivate synchronization with a time server as follows:¤Open the following Web page: Settings ¢Miscellaneous. ¤In the Automatic adjustment of System Time with Time Server field select Yes to activate synchronization between base station and a time server. If you select No the base station will not adopt time settings from a time server. In this case set the time and date manually using a handset. ¤The Last synchronisation with time server field shows the last time the base sta-tion compared the time and date settings with a time server. ¤In the Time Server field, enter the Internet address or name of the time server from which the base station should adopt its time and date settings (maxi-mum 74 characters). The time server "europe.pool.ntp.org" is set as default on the base station. You can overwrite the setting. ¤From the Country list, select the country in which your base station is being operated. ¤The Time Zone field shows the valid time zone for the Country. It shows the deviation between local time (not daylight saving time) and Greenwich Mean Time (GMT).If a country is divided into various time zones, they will all appear in the list. Select the appropriate Time Zone for the base station from the list. ¤The Automatically adjust clock to summer-time changes field is displayed if your time zone differentiates between daylight saving time and standard time. Select On to change the time automatically to daylight saving time or stand-ard time when daylight saving time begins and ends respectively. Select Off if you do not want to change to daylight saving time. Please note: If the date and time are updated by a time server that automat-ically switches between daylight saving time and standard time, you must always select Off here. ¤Select the Set button to save the settings in your phone. Once you have activated synchronization, the time and date will be compared with a time server as soon as an Internet connection is established. Synchronization will usually occur once a day (at night) if synchronization is activated. Any additional synchronization will take place only after each new system start of the base station (e.g. after a firmware update or a power cut). If you register a new handset on your base station it will assume the time and date of the base station without any additional synchronization with the time server.
140Setting the phone with the PCGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / web_server.fm / 24.04.2009Version 8, 03.09.2008Date and time settings are transferred to every handset after synchronization. Querying the phone statusGeneral information about your phone is displayed. ¤In the menu list, select the Status tab. The following information is displayed:Area: IP Configuration IP address The phone's current IP address within the local network. For information on assigning the IP address, £Page 103. MAC addressThe phone's device address. Area: Software Firmware version Version of the firmware currently downloaded. You can download updates of the firmware to your phone (£Page 87). Firmware updates are available on the Internet. EEPROM version Version of your phone's EEPROM storage chip (£Page 175). Please noteuThe default time server "europe.pool.ntp.org" will remain stored in the base station even if you overwrite it. If you delete your time server from the Time Server field and synchronization is still activated, the base station will continue to synchronize with the default time server. However, it will no longer appear in the Time Server field. uIf you have entered your own time server in the Time Server field and the base station is unable to synchronize for ten consecutive attempts, the base station will synchronize with the default time server. uIf you have deactivated synchronization with a time server, and if the date and time are not set on any handset, then the base station will attempt to reference date and time settings from the CID information of an incoming call.
141Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Getting help with your phoneQuestions and answersIf you have any questions about the use of your phone, you can contact us 24/7 at www.gigaset.com/customercare. The table below contains a list of common problems and possible solutions.Please noteTo ensure the quickest and most efficient response from Customer Service, please have the following information available:uVersion of firmware, EEPROM and your phone's MAC addressYou can check this information with the Web configurator (£Page 140). For displaying the MAC address on your handset, £Page 93uVoIP status code (£Page 145)For problems with VoIP connections, set VoIP status messages to be dis-played on your handset (£Page 90, Page 136). These messages contain a status code that helps when the problem is analyzed.The display is blank. 1. The handset is not switched on.¥Press and hold the End Call key a.2. The battery is flat.¥Charge the battery or replace it (£Page 11)."Base" flashes in the display.1. The handset is out of range of the base station or the base station's range has decreased because Eco mode is active.¥Move the handset closer to the base station.¥If necessary, deactivate Eco mode (£Page 69).2. The handset has been deregistered.¥Register the handset (£Page 71).3. The base station is not turned on.¥Check the base station's power adapter (£Page 18).4. The base station firmware is currently being updated (automatically).¥Please wait until the update is complete.
142Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Handset does not ring. 1. The ringer melody is deactivated.¥Activate the ringer melody (£Page 82).2. Call forwarding set to All Calls.¥Deactivate call forwarding (VoIP £Page 53/Page 121).You cannot hear a ringer melody/dialing tone from the fixed line network. The phone cord supplied has not been used or has been replaced by a new cord with the wrong pin connections.¥Please always use the phone cord supplied or ensure that the pin connections are correct when purchasing from a retailer (£Page 152).Error tone sounds after system PIN prompt.You have entered the wrong system PIN.¥Re-enter system PIN. Have you forgotten the system PIN?¥Reset the base station to set the system PIN back to 0000 (£Page 85).The other party cannot hear you. You have pressed the k key or the §Mute§ Display key. The handset is "muted".¥Press the   or §On§ Display key to re-activate the microphone (£Page 45).When making calls from the fixed line network, the caller's phone number is not displayed although CID (£Page 42) is set. Caller ID is not enabled.¥The caller should ask his network provider to enable Caller ID (CID).You hear an error tone when keying an input (a descending tone sequence).Action has failed/invalid input. ¥Repeat the operation. Watch the display and refer to the user guide if necessary.You cannot connect to the router and the phone is assigned a static IP address. ¥Check on the router whether the IP address is already being used by another device in the LAN or belongs to the block of IP addresses that is reserved on the router for dynamic address assignment.¥If necessary, change the phone's IP address (£Page 91).You have made a call via VoIP but cannot hear the other caller.Your phone is connected to a router with NAT/firewall. ¥Your STUN server (£Page 112) or outbound proxy (£Page 113) settings are incomplete or incorrect. Check the settings.¥No outbound proxy is entered or the outbound proxy mode Never is activated (£Page 113) and your phone is connected to a router with symmetric NAT or a blocking firewall. ¥Port forwarding is activated on your router, but no permanent IP address has been assigned to your phone.Ç
143Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008You cannot make calls via VoIP. Server not accessible! is displayed.¥First wait a few minutes. This is often a short-term event that corrects itself after a short time. If the message continues to be displayed, proceed as follows: ¥Check whether your phone's Ethernet cable is correctly connected to the router. ¥Check your router's cable connection to the Internet. ¥Check whether the phone is connected to the LAN. Send a ping command, e.g. from your PC, to the phone (ping s<local IP address of the phone>). It may be that no IP address could be assigned to the phone or a permanently set IP address is already assigned to another LAN subscriber. Check the settings on the router, you may have to activate the DHCP server. You cannot make calls via VoIP. SIP registration failed is displayed. ¥First wait a few minutes. This is often a short-term event that corrects itself after a short time.The message may still be displayed for the following reasons: 1.  The personal VoIP access data ( Username, Authentication Name and Authentication Pass-word) that you have entered is incomplete or incorrect. ¥Check your information. Particularly check your use of upper and lower case.2.  The general settings for your VoIP provider are incomplete or incorrect (incorrect server address). ¥Start the Web configurator and check the settings.You cannot make calls via VoIP. VoIP config. error: xxx appears in the display (xxx = VoIP status code). You are trying to make a call via a VoIP connection that is not properly configured.¥Start the Web configurator and check the settings. Possible status codes and their meanings are listed on Page 145. The phone does not dial an entered number. The display shows Not possible!. The number may be blocked (dialing plan). ¥Open the Dialling Plans Web page of the Web configurator and delete or deactivate the block if necessary. You cannot establish a connection to the phone with your PC's Web browser. ¥When establishing a connection, check the phone's local IP address that has been entered. You can check the IP address on your handset. ¥Check the LAN connections for the PC and phone. ¥Check that your phone can be reached. Send a ping command, e.g. from your PC, to the phone (ping s <local IP address of the phone>).¥You have tried to reach the phone via a secure http (https://…). Try again with http://… You cannot be reached for calls from the Internet. ¥There is no entry for your phone in your router's routing table. Check the settings for the NAT refresh time (£Page 113).¥Your phone is not registered with the VoIP provider. ¥You have entered the wrong user ID or an incorrect domain (£Page 110).
144Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008No firmware update or VoIP profile download is carried out. 1. If Not possible, try later. is displayed, the VoIP connections may be busy or a download/update is already being carried out.¥Repeat the process at a later time.2. If File corrupt is displayed, the firmware or profile file may be invalid. ¥Please only use firmware and downloads that are available on the preconfigured Gigaset configuration server (£Page 137) or at www.gigaset.com/customercare.3. If Server not available is displayed, the download server may not be accessible. ¥The server is currently not accessible. Repeat the process at a later time. ¥You have changed the preconfigured server address (£Page 137). Correct the address. If necessary, reset the base station. 4. If Transmission error XXX is displayed, an error has occurred during the transmission of the file. An HTTP error code is displayed for XXX. ¥Repeat the process. If the error occurs again, consult the Service department. 5. If Check IP settings. is displayed, your phone may not be connected to the Internet.¥Check the cable connections between the phone and router and between the router and the Internet. ¥Check whether the phone is connected to the LAN, i.e. it can be reached at its IP address. You cannot listen to or control a network mailbox. VoIP: Your VoIP provider does not support the type of DTMF signaling set up on your phone. ¥Ask your VoIP provider which signaling it supports and change the settings on your phone (£Page 126) if necessary. When operating the base station within a PABX:Your PABX is set for dial pulsing.¥Set your PABX to touch tone dialing.No time is specified for a message in the Calls list. Date and time have not been set.¥Set date/time (£Page 14) or¥Activate base station synchronization with a time server on the Internet (£Page 139).
145Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Using VoIP status codesIf you have problems with your VoIP connections, activate the Status on HS func-tion (£Page 93, Page 136). You will then receive a VoIP status code that will support you during the problem analysis. Provide the code to the Service department during the problem analysis.In the following tables you will find the meaning of the most important status codes and messages. Status code Meaning 0x31 VoIP config. error: IP domain not entered.0x33 VoIP config. error: SIP user name (Authentication Name) not entered. This is shown, for example, when dialing with a line suffix, if no connection is configured for the suffix on the base station. 0x34 VoIP config. error: SIP password (Authentication password) not entered. 0x300 The called party can be reached under several phone numbers. If the VoIP pro-vider supports this, a list of the phone numbers is transmitted as well as the status code. The caller can select to which number he wants to make the con-nection.  0x301 Permanently redirected.The called party can no longer be reached under this number. The new number is transferred to the phone together with the status code, and the phone then no longer accesses the old number but dials the new address immediately. 0x302 Temporarily redirected. The phone is informed that the called party cannot be reached under the dialed number. The call is redirected for a limited period. The phone is also notified of the length of the redirection. 0x305 The query is sent to a different "proxy server", e.g. to balance incoming que-ries. The phone will make the same query once again to another proxy server. This is not a redirection of the address per se.  0x380 Other service:The query or call could not be transferred. But the phone is notified what other options there are to connect the call. 0x400 Wrong call 0x401 Not authorized 0x403 The requested service is not supported by the VoIP provider. 0x404 Wrong phone number. No connection on this number.Example: In a local call you have not dialed the area code although your VoIP provider does not support local calls. 0x405 Method not permitted. 0x406 Not acceptable.The requested service cannot be provided. 0x407 Proxy authentication required. 0x408 The party cannot be reached (e.g. account has been deleted).
146Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008 0x410 The requested service is not available from the VoIP provider. 0x413 Message is too long. 0x414 URI is too long. 0x415 Query format is not supported. 0x416 URI is faulty. 0x420 Incorrect ending 0x421 Incorrect ending 0x423 The requested service is not supported by the VoIP provider. 0x480 The dialed number is temporarily unavailable. 0x481 The recipient is not available. 0x482 Double service query 0x483 Too many "jumps":The query was rejected because the service server (proxy) has decided that this query has already passed through too many service servers. The maxi-mum number is defined beforehand by the original sender of the query. 0x484 Wrong number:In most cases this response means that you have simply omitted one or more digits in the phone number. 0x485 The URI dialed is not unique and cannot be processed by the VoIP provider.  0x486 The called party is busy. 0x487 General faults:The call was canceled before a call was established. The status code confirms receipt of the interruption signal. 0x488 The server cannot process the query because the data entered in the media description is not compatible. 0x491 The server notifies that the query will be processed as soon as a previous query has been completed.  0x493 The server rejects the query because the phone cannot decrypt the message. The sender has used an encryption method that neither the server nor the receiver phone can decrypt. 0x500 The proxy or the receiving device has discovered a fault while executing the query. It is therefore impossible to execute the query. If this occurs, the caller or the phone displays the fault and repeats the query after a few seconds. The number of seconds after which the query can be repeated may be transmitted to the caller or phone by the receiving device. 0x501 The query cannot be processed by the recipient because the recipient does not have the functionality that the caller requires. If the recipient understands the query but does not process it because the sender does not have the nec-essary rights or the query is not permitted in the current context, status code 405 is transmitted instead of 501.  0x502 In this case, the receiving device that transmits this error code is a proxy or a gateway and has received an invalid response from its gateway via which this query is to be processed.Status code Meaning
147Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008 0x503 The query can currently not be processed by the receiving device or the proxy because the server is either overloaded or is being serviced. If it is possible for the query to be repeated in the foreseeable future, the server informs the caller or the phone of this.  0x504 Time limit exceeded at the gateway. 0x505 The server rejects the query because the indicated version number of the SIP protocol does not at least concur with the version that is used by server or the SIP device involved in this query. 0x515 The server rejects the query because the message exceeds the maximum per-mitted size. 0x600 The called party is busy. 0x603 The called party has rejected the call. 0x604 The called URI does not exist. 0x606 The communication settings are not acceptable. 0x701 The called party has hung up. 0x703 Connection canceled because of time-out.  0x704 Connection interrupted because of a SIP error. 0x705 Wrong dialing tone 0x706 No connection established 0x751 Busy tone:No codec match between the calling and called party. 0x810 General socket layer error: User is not authorized. 0x811 General socket layer error: Wrong socket number 0x812 General socket layer error: Socket is not connected. 0x813 General socket layer error: Memory error. 0x814 General socket layer error: Socket not available – check IP settings/connection problem/VoIP setting incorrect. 0x815 General socket layer error: Illegal application on the socket interface.Status code Meaning
148Getting help with your phoneGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Checking service informationYou may need the service information of your phone (base station and hand-set) for Customer Service. Base station service informationPrerequisite: You are conducting an external call. The connection has been established for at least 8 seconds.§Menu§ ¢Service InfoConfirm selection with §OK§. The following information/functions can be selected with q:1:  Serial number of the base station (RFPI)2:  Serial number of your handset (IPUI)3: Informs the service employees of the base station settings (in hex format), e.g. the number of registered handsets. The last 4 digits indicate the number of operating hours (hexadecimal). 4:  Variant (digits 1 to 2), version of the base station firmware (digits 3 to 5).5:  Gigaset.net number of your phone. With this number a service employee can call you over the Internet without you needing to be registered with a VoIP provider. This means that the employee can test online connections and VoIP telephony regardless of the VoIP provider.6:  Device number of the base station. Contains further information for the service employee. Unlock SystemConfirm selection with §OK§. You can use a code to cancel any provider-specific device lock that may have been set.Update ProfileConfirm selection with §OK§. The current profiles of your VoIP providers (general provider data of all configured VoIP connections) are automatically loaded onto your phone. The general settings for all VoIP connections for which profiles are available on the Gigaset server are updated.Handset service informationWhen the handset is in idle status:Press the Display key §Menu§.¤Press the following keys one after the other: *#QL#.The information displayed on the handset includes: 1: Serial number (IPUI)2: Number of operating hours 3: Variant, version of handset software
149Protecting our environmentGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Protecting our environmentOur environmental mission statement We, Gigaset Communications GmbH, bear social responsibility and are actively committed to a better world. Our ideas, technologies and actions serve people, society and the environment. The aim of our global activity is to secure sustain-able life resources for humanity. We are committed to a responsibility for our products that comprises their entire life cycle. The environmental impact of products, including their manufacture, procurement, distribution, utilization, service and disposal, are already evaluated during product and process design. Further information on environmentally friendly products and processes is available on the Internet at www.gigaset.com.Environmental management systemGigaset Communications GmbH is certified pursuant to the international standards EN 14001 and ISO 9001.ISO 14001 (Environment): certified since September 2007 by TüV SÜD Management Service GmbH.ISO 9001 (Quality): certified since 17/02/1994 by TüV Süd Management Service GmbH.Ecological energy consumptionThe use of ECO DECT (£Page 69) saves energy and is an active contribution towards protecting the environment. DisposalBatteries should not be disposed of in general household waste. Observe the local waste disposal regulations, details of which can be obtained from your local authority or the dealer you purchased the product from.All electrical and electronic equipment must be disposed of separately from general household waste using the sites designated by local authorities.If a product displays this symbol of a crossed-out trash can, the product is subject to European Directive 2002/96/EC.Appropriate disposal and separate collection of used equip-ment help to prevent potential harm to both the environment and health. They are a prerequisite for the re-use and recycling of used electrical and electronic equipment.For further information on disposing of your used equipment, please contact your local authority or refuse collection service or the dealer you purchased the product from.
150AppendixGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008AppendixCareWipe the base station, charging cradle and the handset with a damp cloth (do not use solvent) or an antistatic cloth. Never use a dry cloth as this can cause static. Contact with liquidIf the handset should come into contact with liquid:¤Switch off the handset and remove the battery pack immediately.¤Allow the liquid to drain from the handset.¤Pat all parts dry, then place the handset with the battery compartment open and the keypad facing down in a dry, warm place for at least 72 hours (not in a microwave, oven, etc.).¤Do not switch on the handset again until it is completely dry.When it has fully dried out, you will normally be able to use it again.SpecificationsRecommended batteriesTechnology:Nickel-metal-hydride (NiMH)Size: AAA (Micro, HR03)Voltage: 1.2 VCapacity: 550–1000 mAhWe recommend the following battery types, because these are the only ones that guarantee the specified operating times, full functionality and long service life:uGP 700 mAhuYuasa Phone 700 mAhuYuasa Phone 800 mAhuYuasa AAA 800uPeacebay 600 mAhThe device is supplied with two recommended rechargeable batteries.!
151AppendixGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Handset operating times/charging timesThe operating time of your Gigaset depends on the capacity and age of the bat-teries and the way they are used. (All times are maximum possible times).At the time of going to print, batteries up to 800 mAh were available and had been tested in the system. Due to the constant progression in battery develop-ment, the list of recommended batteries in the FAQ section of the Gigaset Customer Care pages is regularly updated:www.gigaset.com/customercareBase station power consumption The power consumption for the base station is approx. 1.3 watt.Power consumption of the charging cradleCapacity (mAh) approx.550 650 800 1000Standby time (hours) 180 210 265 330Talktime (hours) 23 25 33 41Operating time for 1.5 hrs of calls per day (hours) 80 95 115 145Charging time, base station (hours) 8 10 12 15Charging time, charging cradle (hours) 6 7 9 11Charging (maximum charge current): approx. 1.4 watt Sustained charge: approx. 0.6 wattNot charging (only the network adaptor): approx. 0.3 watt
152AppendixGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008General specificationsPin connections on the telephone jackIf you buy a replacement phone cord from a retailer, make sure that the phone jack has the correct pin assignment.Writing and editing textThe following rules apply when writing text:uUse ts to move the cursor to the right or left.uCharacters are inserted to the left of the cursor.uThe first letter of the name of directory entries is automatically capitalized, followed by lower case letters.Interfaces Fixed line network, EthernetNo. of channels 60 duplex channelsRadio frequency range 1880–11900 MHzDuplex method Time multiplex, 10 ms frame lengthChannel grid 1728 kHzBit rate 1152 kbit/sModulation GFSKLanguage code  32 kbit/sTransmission power 10 mW, average power per channelRange up to 328 yards outdoors, up to 55 yards indoorsBase station power supply 230 V ~/50 HzEnvironmental conditions in operation+41°F to +113°F; 20% to 75% relative humidityCodecs G.711, G.726, G.729AB with VAD/CNG, G.722Quality of Service TOS, DiffServProtocols DECT, GAP, SIP, RTP, DHCP, NAT Traversal (STUN), HTTPDialing mode DTMF (touch tone dialing)/DP (dial pulsing)1unused2unused3a4b5unused6unused3 214 5 6
153AppendixGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Writing text/names Press the relevant key several times to enter letters/characters.Standard charactersWhen you press and hold a key, the characters of that key appear in the display and are highlighted one after the other. When you release the key, the high-lighted character is inserted into the input field. Setting upper/lower case or digitsPress the Pound key # briefly to switch from "Abc" mode to "123" and from "123" to "abc" and from "abc" to "Abc" (upper case: 1st letter upper case, all others lower case). Press the Pound key #before entering the letter.You can see briefly in the display whether upper case, lower case or digits is selected.1x 2x 3x 4x 5x 6x 7x 8x 9x 10x12abc2äáàâãç3def 3ëéèê4gh i4ïíìî5jkl5Lmno6öñóòôõMpqr s 7ßNt uv8üúùûOwx y z 9 ÿ ý æø åQ.,?!01)Space2)Line break1) 2)
154AppendixGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Industry Canada CertificationOperation is subject to the following two conditions (1) this device may not cause inter-ference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network, protective, oper-ational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equip-ment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be con-nected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.This precaution may be particularly important in rural areasNOTE: Users should not attempt to make such connections themselves, but should con-tact the appropriate electric inspection authority, or electrician, as appropriate.This product meets the applicable Industry Canada technical specifications.The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all devices does not exceed five.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
155FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008FCC / ACTA InformationWarning: Changes or modifications to this unit not expressly approved by Gigaset Com-munications USA LLC could void the FCC authority to operate the equipment. This includes the addition of any external antenna device.This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of the base station is a label that contains, among other infor-mation, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.The REN is used to determine the number of devices that may be connected to a tele-phone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.A copy of the supplier's Declaration of Conformity (SDoC) is available at this Internet address: www.gigaset.com/docs.If this equipment causes harm to the telephone network, the telephone company will notify you in advance, that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the tele-phone company will provide advance notice in order for you to make necessary modifi-cations to maintain uninterrupted service. If you experience trouble with this telephone system, disconnect it from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning.If trouble is experienced with this equipment, for repair or warranty information, please contact Support at 1-866-247-8758. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. This equipment is of a type that is not intended to be repaired by the Customer (user).This telephone system may not be used on coin service provided by the telephone com-pany. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for informa-tion. Privacy of communications may not be ensured when using this phone.If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.This telephone system equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Some cordless telephones operate at frequencies that may cause interference to nearby TV’s and VCR’s; to minimize or prevent
156FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008such interference, the system base should not be placed near or on top of a TV or VCR; and, if interference is experienced, moving the base farther away from the TV or VCR will often reduce or eliminate the interference. However, there is no guarantee that interference will not occur in a particular installa-tion. If this telephone system does cause harmful interference to radio or television reception, which can be determined by turning the system off and on, the user is encour-aged to try to correct the interference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the base station and receiver.3. Connect the base station into an outlet on a circuit different from that to which the receiver is connected.4. Consult the dealer or an experienced radio TV technician for help.Notice for Direct Inward Dialing ("DID")ALLOWING THIS EQUIPMENT TO BE OPERATED IN SUCH A MANNER AS TO NOT PROVIDE FOR PROPER ANSWER SUPERVISION IS A VIOLATION OF PART 68 OF THE FCC‘S RULES.Notice to Hearing Aid Wearers: This phone system is compatible with inductively coupled hearing aids.Power Outage: In the event of a power outage, your cordless telephone will not operate. The cordless telephone requires electricity for operation. You should have a telephone that does not require electricity available for use during power outages.Notice: The installation of the base unit should allow at least 8 inches between the base and per-sons to be in compliance with FCC RF exposure guidelines.For body worn operation, the portable part (handset) has been tested and meets FCC RF exposure guidelines. Use with an accessory that contains metal parts may not ensure compliance with FCC RF exposure guidelines.Notice to telephone company service:If you need service from your telephone company, please provide them with the infor-mation– Facility interface Code (FIC)– Service Order Code (SOC)– Universal Service Order Code (USOC) as indicated on the label on the bottom side of the base station.
157FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Safety precautionsBefore using your telephone equipment, basic safety instructions should always be fol-lowed to reduce the risk of fire, electric shock and injury to persons. 1. Read and understand all instructions.2. Follow all warnings and instructions marked on the product.3. Unplug this product from the wall telephone jack and power outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use damp cloth for cleaning. 4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.5. Place this product securely on a stable surface. Serious damage and/or injury may result if the unit falls.6. Slots or openings in the cabinet and the back and bottom are provided for ventilation, to protect it from overheating. These openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register, or in a place where proper ventilation is not provided.7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of AC line power to your home, consult your dealer or local power company.8. Do not place objects on the power cord. Install the unit where no one can step or trip on the cord.9. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.10. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in the risk of fire or electric shock. Never spill liquid of any kind on this product.11. To reduce the risk of electric shock or burns, do not disassemble this product. Take it to a qualified service center when service is required. Opening or removing covers may expose you to dangerous voltages, dangerous electrical current or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.12. Unplug the product from the wall outlet and refer servicing to qualified service per-sonnel under the following conditions:a.) When the power cord is damaged or frayed.b.) If liquid has been spilled into the product. c.) If the product has been exposed to rain or water. d.) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and may require extensive work by a qualified technician to restore the product to normal operation. e.) If the product has been dropped or physically has been damaged. f.) If the product exhibits a distinct change in performance. 13. Avoid using a telephone (other than a cordless type) during a thunderstorm. There may be a remote risk of electrical shock from lightning. Therefore we suggest a surge arrestor.14. Do not use the telephone to report a gas leak in the vicinity of the leak.15. Emergency/911 numbers may not be dialed if the keypad is locked.16. Minimum No. 26 AWG telecommunication line cord must be used with this phone.
158FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008BATTERY SAFETY PRECAUTIONSTo reduce the risk of fire, injury or electric shock, and to properly dispose of batteries, please read and understand the following instructions.CONTAINS NICKEL METAL HYDRIDE BATTERY. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. DO NOT DISPOSE OF IN MUNICIPAL WASTE.1. Only use the batteries specified for use with this product.2. DO NOT USE NICKEL CADMIUM OR LITHIUM BATTERIES, or mix batteries of different sizes or from different manufacturers in this product. DO NOT USE NONRECHARGEABLE BATTERIES.3. Do not dispose of the batteries in a fire; the cells may explode. Do not expose batteries to water. Check with local codes for special disposal instructions.4. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. The electrolyte may be toxic if swallowed.5. Exercise care in handling the batteries in order not to short the batteries with conduct-ing materials such as rings, bracelets, and keys. The batteries or conducting material may overheat and cause burns or fire.6. Charge the batteries provided with, or identified for use with, this product only in accordance with the instructions and limitations specified in the user’s manual. Do not attempt to charge the batteries with any means other than that specified in the users manual.7. Periodically clean the charge contacts on both the charger and handset.
159FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Service (Customer Care)Customer Care Warranty for Cordless ProductsTo obtain Customer Care Warranty service,product operation information, or for problem resolution, call:Toll Free: 1-866-247-87587:00 a.m. – 7:00 p.m. EST Monday-Saturday excluding holidays (English)7:00 a.m. - 12:00 p.m. (noon) EST Monday-Saturday excluding holidays (French)End-user limited warrantyThis product is covered by a one year limited warranty. Any repair replacement or war-ranty service, and all questions about this product should be directed to: 1-866-247-8758.This limited, non-transferable warranty is provided to the original buyer/end-consumer ("you") for systems, handsets and accessories (collectively, "Product") provided by Gigaset Communications USA LLC or Gigaset Communications Canada Inc. (collectively "Gigaset NAM"). Gigaset NAM warrants to you that at the date of purchase, the Product is free of defects in workmanship and materials and the software included in the Product will per-form in substantial compliance to its program specifications.1. WARRANTY PERIODThe Product warranty period is one (1) year from the original date of purchase by you. Proof of purchase (e.g., sales slip or invoice) must be provided with any Product returned during the warranty period. Batteries supplied with the Products are warranted to be free from defects at the time of purchase only.2. EXCLUSIVE REMEDYGigaset NAM's entire liability and your exclusive remedy if the Product is defective in materials or workmanship during the warranty period and is returned shall be that the Product will be repaired or replaced as set forth in Section 4 below. Reconditioned replacement components, parts or materials may be used in the replacement or repair. Data in the memory of the Product may be lost during repair.3. THIS LIMITED WARRANTY DOES NOT COVER AND IS VOID WITH RESPECT TO THE FOLLOWING:– Cosmetic damage, physical damage to the surface of the Product, including, without limitation, breakage, cracks, dents, scratches or adhesive marks on the LCD screen or outside casing of the Product.– Products which have been repaired, maintained or modified (including the antenna) by anyone other than Gigaset NAM or a Gigaset NAM-approved repair facility, or that have been improperly installed. – Cost of installation, removal or reinstallation.– Damage due to any telephone, electronic, hardware or software program, network, Internet or computer malfunctions, failures, or difficulties of any kind, including with-out limitation, server failure or incomplete, incorrect, garbled or delayed computer transmissions.– Equipment and components not manufactured, supplied or authorized by Gigaset NAM.
160FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008– Modification of the Product's components, or operation of the Product in an unsuita-ble environment or in a manner for which it is not intended, including but not limited to failures or defects caused by misuse, abuse, accidents, physical damage, abnormal operation, improper handling or storage, neglect, alterations, unauthorized installa-tion, removal or repairs, failure to follow instructions, problems caused by the carrier's network coverage, exposure to fire, water or excessive moisture or dampness, floods, or extreme changes in climate or temperature, acts of God, riots, acts of terrorism, spills of food or liquids, viruses or other software flaws introduced into the Product or other acts which are not the fault of Gigaset NAM and which the Product is not spec-ified to tolerate, including damage caused by mishandling or blown fuses.– Products which have had warranty stickers, electronic serial number and/or serial number label removed, altered, rendered illegible or fraudulently applied to other equipment.– Signal reception problems (unless caused by defect in material or workmanship in the Product).– Products operated outside published maximum ratings.– Performance of the Products when used in combination with other products or equip-ment not manufactured, supplied or authorized by Gigaset NAM.– Consumables (such as batteries and fuses).– Payments for labor or service to representatives or service centers not authorized to perform product maintenance by Gigaset NAM.–Loss of data.– Testing and examination discloses that the alleged defect or malfunction in the Prod-uct does not exist.This warranty does not cover customer education, instruction, installation or removal, set up adjustments, problems related to service(s) provided by a carrier or other service provider, and/or signal reception problems. Gigaset NAM shall not be responsible for soft-ware, firmware, information, or memory data contained in, stored on, or integrated with any Products returned for repair, whether under warranty or not. This warranty is valid only in the country in which it is purchased (i.e., the United States of America or Canada respectively, but not both).USE WITH ACCESSORIES NOT SUPPLIED BY GIGASET NAM OR NOT OTHERWISE EXPRESSLY AUTHORIZED BY GIGASET NAM MAY VOID WARRANTY.4. WARRANTY CLAIM PROCEDUREAll warranty claims must be made by notifying Gigaset NAM prior to the expiration of the warranty period. Gigaset NAM's obligation to provide warranty support shall not extend past the end of the warranty period, except that any product repaired or replaced during the warranty period shall continue to be warranted for the balance of such warranty period or thirty (30) days, whichever is greater.Throughout the warranty period, Support will be available 7:00 a.m. – 7:00 p.m. EST Monday-Saturday (English) and 7:00 a.m. - 12:00 p.m. (noon) EST Monday-Saturday (French), excluding National holidays. Support service will be provided for you by access-ing the toll free customer service number:1-866-247-87585. LIMITATION OF WARRANTYGigaset NAM makes no warranty or representation that the software in the Products will meet your requirements or will work in combination with any hardware or applications software products provided by third parties, that the operation of the software will be uninterrupted or error free, or that all defects in the software products will be corrected.
161FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.20086. LIMITATION ON REMEDIES; NO CONSEQUENTIAL OR OTHER DAMAGESYour exclusive remedy for any breach of this limited warranty is as set forth above. Except for any refund elected by Gigaset NAM, YOU ARE NOT ENTITLED TO ANY DAMAGES, INCLUDING BUT NOT LIMITED TO CONSEQUENTIAL DAMAGES, if the Product does not meet the limited warranty , and, to the maximum extent allowed by applicable law, even if any remedy fails of its essential purpose. The terms below ("Exclusion of Incidental, Consequential and Certain Other Damages") are also incorporated into this limited war-ranty . Some states/jurisdictions/provinces do not allow the exclusion or limitation of inci-dental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights. You may have others which vary from state/jurisdiction/province to state/jurisdiction/province.7. DISCLAIMER OF WARRANTIESGIGASET NAM AND ITS SUPPLIERS PROVIDE THE PRODUCT AND SUPPORT SERVICES (IF ANY) AS IS AND WITH ALL FAULTS. THE LIMITED WARRANTY IS IN LIEU OF ANY OTHER EXPRESS WARRANTIES (IF ANY) CREATED BY ANY DOCUMENTATION OR PACKAGING EXCEPT FOR THE LIMITED WARRANTY, AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IS IN LIEU OF ANY IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, OF ACCURACY OR COMPLETENESS OR RESPONSES, OF RESULTS, OF WORKMANLIKE EFFORT, OF LACK OF VIRUSES AND OF LACK OF NEGLI-GENCE, ALL WITH REGARD TO THE PRODUCT, AND THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES. ALSO, THERE IS NO WARRANTY OR CONDITION OF TITLE, QUIET ENJOYMENT, QUIET POSSESSION, OR CORRESPONDENCE TO DESCRIPTION OR NONINFRINGEMENT WITH REGARD TO THE PRODUCT. Some states/jurisdictions/prov-inces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above exclusions or limitations may not apply to you. If an implied warranty or condition is created by your state/prov-ince and federal or state/provincial law prohibits disclaimer of it, you also have an implied warranty or condition, BUT ONLY AS TO DEFECTS DISCOVERED DURING THE PERIOD OF THIS LIMITED WARRANTY (ONE YEAR). AS TO ANY DEFECTS DISCOVERED AFTER THE ONE YEAR PERIOD, THERE IS NO WARRANTY OR CONDITION OF ANY KIND. This limited war-ranty gives you specific legal rights, and you may also have other rights which vary from state to state/province to province. In no event shall Gigaset NAM's liability exceed the cost of repairing or replacing defective Products as provided herein, and any such liabili-ties will terminate upon expiration of the warranty period.Any supplements or updates to the Product or the software in the Product, including without limitation, any (if any) software fixes or upgrades or bug fixes provided to you after the expiration of the one year limited warranty period are not covered by any war-ranty or condition, express, implied or statutory.
162FCC / ACTA InformationGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.20088. EXCLUSION OF INCIDENTAL, CONSEQUENTIAL AND CERTAIN OTHER DAMAGESTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL GIGASET NAM, SELLER OR THEIR SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS OR CONFIDENTIAL OR OTHER INFORMATION, FOR BUSINESS INTERRUPTION, FOR PERSONAL INJURY, FOR LOSS OF PRIVACY, FOR FAILURE TO MEET ANY DUTY INCLUDING OF GOOD FAITH OR OF REASONABLE CARE, FOR NEGLI-GENCE, AND FOR ANY OTHER PECUNIARY OR OTHER LOSS WHATSOEVER) ARISING OUT OF OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES, OR OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF THIS LIMITED WARRANTY, EVEN IN THE EVENT OF THE FAULT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY, BREACH OF CONTRACT OR BREACH OF WARRANTY OF GIGASET NAM OR SELLER OR ANY SUPPLIER, AND EVEN IF GIGASET NAM OR SELLER OR ANY SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REPAIR OR REPLACEMENT, AS PROVIDED UNDER THE WARRANTY, IS YOUR SOLE AND EXCLUSIVE REMEDY FOR BREACH OF THE LIMITED WARRANTY.9. LIMITATION OF LIABILITY AND REMEDIESNOTWITHSTANDING ANY DAMAGES THAT YOU MIGHT INCUR FOR ANY REASON WHATSO-EVER (INCLUDING, WITHOUT LIMITATION, ALL DAMAGES REFERENCED ABOVE AND ALL DIRECT OR GENERAL DAMAGES), THE ENTIRE LIABILITY OF GIGASET NAM, SELLER AND ANY OF THEIR SUPPLIERS UNDER ANY PROVISION OF THIS LIMITED WARRANTY AND YOUR EXCLUSIVE REMEDY FOR ALL OF THE FOREGOING (EXCEPT FOR ANY REMEDY OF REPAIR OR REPLACEMENT ELECTED BY GIGASET NAM OR SELLER OR SUPPLIER WITH RESPECT TO ANY BREACH OF THE LIMITED WARRANTY) SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT OR FIVE DOLLARS ($5.00 USD/CAN). THE FOREGOING LIMITATIONS, EXCLUSIONS AND DISCLAIMERS SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, EVEN IF ANY REMEDY FAILS ITS ESSENTIAL PURPOSE.10. GOVERNING LAWIf this Product was purchased in the United States of America this limited warranty will be governed by the laws of Texas, and exclude the United Nations Convention on Con-tracts for the International Sale of Goods. If this Product was purchased in Canada this limited warranty will be governed by the laws of the Province of Ontario and the federal laws of Canada applicable therein, and exclude the United Nations Convention on Con-tracts for theInternational Sale of Goods.If you want to learn more about Gigaset Service or for Support on your Gigaset phone, visit our web site at http://www.gigaset.com or please call1-866-247-8758.Issued byGigaset Communications GmbHSchlavenhorst 66, D-46395 BocholtGigaset Communications GmbH is a licensee of the Siemens trademark.© Gigaset Communications GmbH 2009All rights reserved.Subject to availability. Rights of modifications reserved.Product attributes subject to change.We reserve the right, to make changes without notice in equipment design and/or com-ponents.Part Number:A31008-M2009-XXXX-1-XX© Copyright 2009.
http://www.gigaset.com">
http://www.gigaset.com">
163Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Gigaset A580 IP – free software Your Gigaset A580 IP's firmware includes free software that is licensed under the GNU Lesser General Public License. This free software was developed by a third party and is protected by copyright. You will find the license text in its orig-inal English version on the pages that follow. The software is provided free of charge. You are authorized to use this free soft-ware in accordance with the above-mentioned license conditions. In the event of contradictions between these license conditions and the Gigaset Communi-cations GmbH license conditions that apply for the software, the aforemen-tioned license conditions shall take precedence for the free software. The GNU Lesser General Public License (LGPL) is supplied with this product. You can also download the license conditions from the Internet: uThe LGPL is available on the Internet at: http://www.gnu.org/copyleft/lesser.html uThe source text, including copyright notices for free software, is cur-rently available on the Internet at: http://www.gigaset.com/developer For more information and Internet links to the source text of the free software, see the Online Support pages on the Internet at: www.gigaset.com/customercare If it is not already supplied with the product, you can request the source text, including copyright notices, from Gigaset Communications GmbH. There is a charge to cover the cost of copying and postage. Please submit this request by e-mail or fax to the following address or fax number within 3 years of purchas-ing this product. Please state the exact device type plus the version number of the installed device software. Use of the free software contained in this product extending beyond the pro-gram sequence intended by Gigaset Communications GmbH is at the user's own risk – i.e. there shall be no claims for liability for defects against Gigaset Communications GmbH. The GNU Lesser General Public License contains refer-ences to the liability for defects of authors or other proprietors of the free soft-ware. You shall have no right to assert a claim against Gigaset Communications GmbH based on liability for defects if a defect in the product is or could be due to changes you have made to the programs or their configuration. Further-more, you shall have no right to assert a claim against Gigaset Communications GmbH based on liability for defects if the free software violates the copyright of third parties.Gigaset Communications GmbH shall not provide technical support for the software, including the free software included within it, if it has been changed. Small Parts Dispatch Bocholt E-mail: kleinteileversand.com@gigaset.com Fax:  0049 2871 / 91 30 29
164Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008GNU LESSER GENERAL PUBLIC LICENSEVersion 2.1, February 1999Copyright (C) 1991, 1999 Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USAEveryone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]PreambleThe licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.This license, the Lesser General Public License, applies to some specially designated soft-ware packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.When we speak of free software, we are referring to freedom of use, not price. Our Gene-ral Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must pro-vide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full free-dom of use specified in this license.Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
165Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008We call this license the "Lesser" General Public License because it does less to protect the user's freedom than the ordinary General Public License. It also provides other free soft-ware developers less of an advantage over competing non-free programs. These disad-vantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.In other cases, permission to use a particular library in non-free programs enables a gre-ater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.GNU LESSER GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which con-tains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".A "library" means a collection of software functions and/or data prepared so as to be con-veniently linked with application programs (which use some of those functions and data) to form executables.The "Library", below, refers to any such software library or work which has been distri-buted under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a por-tion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".)"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it con-tains, plus any associated interface definition files, plus the scripts used to control com-pilation and installation of the library.Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
166Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.20082. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:a) The modified work must itself be a software library.b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and per-forms whatever part of its purpose remains meaningful.(For example, a function in a library to compute square roots has a purpose that is enti-rely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.Thus, it is not the intent of this section to claim rights or contest your rights to work writ-ten entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, ver-sion 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.This option is useful when you wish to copy part of the code of the Library into a program that is not a library.4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium cus-tomarily used for software interchange.If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
167Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License.Section 6 states terms for distribution of such executables.When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not.Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.If such an object file uses only numerical parameters, data structure layouts and acces-sors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6.Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modifi-cation of the work for the customer's own use and reverse engineering for debugging such modifications.You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distri-buted under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)b) Use a suitable shared library mechanism for linking with the Library. A suitable mecha-nism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is nor-mally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
168Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008It may happen that this requirement contradicts the license restrictions of other proprie-tary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you dis-tribute.7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distri-bute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, subli-cense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, dis-tributing or modifying the Library or works based on it.10. Each time you redistribute the Library (or any work based on the Library), the recipi-ent automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.You are not responsible for enforcing compliance by third parties with this License.11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.If any portion of this section is held invalid or unenforceable under any particular circum-stance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest the validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
169Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.200812. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version num-ber, you may choose any version ever published by the Free Software Foundation.14. If you wish to incorporate parts of the Library into other free programs whose distri-bution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be gui-ded by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRI-BUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.END OF TERMS AND CONDITIONS
170Gigaset A580 IP – free softwareGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / appendix.fm / 24.04.2009Version 8, 03.09.2008Applying These Terms to Your New LibrariesIf you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USAAlso add information on how to contact you by electronic and paper mail.You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:<one line to give the library's name and a brief idea of what it does.>Copyright (C) <year> <name of author>This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.This library is distributed in the hope that it will be useful, but WITHOUT ANY WAR-RANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PAR-TICULAR PURPOSE. See the GNU Lesser General Public License for more details.Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker. <signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice
171AccessoriesGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / accessories_SAG.fm / 24.04.2009Version 8, 03.09.2008AccessoriesGigaset handsetsUpgrade your Gigaset to a cordless PABX:Gigaset A58H handsetuIlluminated graphic displayuIlluminated keypaduHandsfree talkinguPolyphonic ringer melodiesuDirectory for around 150 entrieswww.gigaset.com/gigaseta58hGigaset S67H or S68H handsetuHDSP readyuIlluminated graphical color display (65k colors)uIlluminated keypaduHandsfree talkinguPolyphonic ringer melodiesuDirectory for around 250 entriesuPicture Caller IDuHeadset socketuBluetooth (Gigaset S68H only)uRoom monitorwww.gigaset.com/gigasets67hwww.gigaset.com/gigasets68hAll accessories are available from your phone retailer.Use only original accessories. This will avoid possible health risks and dam-age to property, and also ensure that all the relevant regulations are com-plied with.
172GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008GlossaryAADSL Asymmetric Digital Subscriber LineSpecial form of DSL.ALG  Application Layer GatewayNAT control mechanism of a router. Many routers with integrated NAT use ALG. ALG lets the data packets in a VoIP connection pass and adds the public IP address of the secure private network. The router's ALG should be deactivated if the VoIP provider offers a STUN server or an outbound proxy.  £ Firewall, NAT, Outbound proxy, STUNAuthenticationRestriction of access to a network/service by use of an ID and password to log in. Automatic ringback £ Ringback when the number is busy.BBlock dialingEnter the complete phone number, and correct it if necessary. Then pick up the handset or press the Handsfree key to dial the phone number. Broadband Internet access £ DSL.Buddy  Subscriber with whom you exchange brief messages on the Internet in real time (chatting).  £Instant messaging. CCall waiting  = CWVoIP provider feature. A beep during a call indicates that another caller is wait-ing. You can accept or reject the second call. You can activate/deactivate the feature.
173GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008Call forwarding = CFAutomatic forwarding (CF) of a call to a different telephone number. There are three kinds of call forwarding: uCFU, Call Forwarding UnconditionaluCFB, Call Forwarding Busy uCFNR, Call Forwarding No ReplyCF   £ Call forwardingChatting Form of communication on the Internet. During a chat, brief messages are exchanged between the communicating parties in real time. Chatting in this sense is understood to be a written form of communication. Client Application that requests a service from a server.Codec  Coder/decoderCodec is a procedure that digitizes and compresses analog voice before it is sent via the Internet, and decodes – i.e. translates into analog voice – digital data when voice packets are received. There are different codecs, with differing degrees of compression, for instance. Both parties involved in the telephone connection (caller/sender and recipient) must use the same codec. This is negotiated between the sender and the recip-ient when establishing a connection. The choice of codec is a compromise between voice quality, transmission speed and the necessary bandwidth. A high level of compression, for example, means that the bandwidth required for each voice connection is low. However, it also means that the time needed to compress/decompress the data is greater, which increases execution time for data in the network and thus impairs voice quality. The time required increases the delay between the sender speaking and the recipient hearing what has been said. COLP / COLRConnected Line Identification Presentation/RestrictionService characteristic of a VoIP connection for outgoing calls.COLP displays the phone number accepting the call on the calling party's dis-play unit. The number of the party accepting the call is different to the dialed number, e.g. if the call is forwarded or transferred. The called party can use COLR (Connected Line Identification Restriction) to prevent the number from appearing on the calling party's display. Consultation callYou are on a call. With a consultation call, you interrupt the conversation briefly to establish a second connection to another participant. If you terminate the connection to this participant immediately, then this was a consultation call. If you switch between the first and second participant, it is called Toggling.CW   £ Call waiting
174GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008DDHCP  Dynamic Host Configuration ProtocolInternet protocol which regulates the automatic assignment of IP addresses to Network subscribers. The protocol is made available in the network by a server. A DHCP server can, for example, be a router.The phone contains a DHCP client. A router that contains a DHCP server can assign the IP addresses for the phone automatically from a defined address block. The dynamic assignment means that several Network subscribers can share one IP address, although they can only use it alternately and not simulta-neously.With some routers you can specify that the IP address for the phone is never changed.Displayed nameVoIP provider feature. You can specify any name that is to be shown to the other party during a call instead of your phone number.DMZ (Demilitarized Zone)DMZ describes a part of a network that is outside the firewall.A DMZ is set up, as it were, between a network you want to protect (e.g. a LAN) and a non-secure network (e.g. the Internet). A DMZ permits unrestricted access from the Internet to only one or a few network components, while the other network components remain secure behind the firewall.DNS  Domain Name SystemHierarchical system that enables assignment of IP addresses to Domain names that are easier to memorize. This assignment must be managed in each (W)LAN from a local DNS server. The local DNS server determines the IP address, if necessary by enquiring about superordinate DNS servers and other local DNS servers on the Internet. You can specify the IP address of the primary/secondary DNS server.  £ DynDNS.Domain nameName of one (several) Web server(s) on the Internet (e.g. gigaset.net). The domain name is assigned to the relevant IP address by DNS.DSCP  Differentiated Service Code Point £ Quality of Service (QoS).DSL  Digital Subscriber LineData transfer technology that allows Internet access with, for e.g. 1.5 Mbps over a conventional telephone line. Prerequisites: DSL modem and the appro-priate service offered by the Internet provider.DSLAM  Digital Subscriber Line Access MultiplexerThe DSLAM is a switch cabinet in an exchange at which all subscriber connec-tors converge.
175GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008DTMF  Dual Tone Multi-FrequencyAnother description for dual tone multi-frequency dialing (DTMF).Dynamic IP addressA dynamic IP address is assigned to a network component automatically via DHCP. The dynamic IP address for a network component can change every time it registers or at certain time intervals. £ Static IP addressDynDNS  Dynamic DNSDomain names and IP addresses are assigned via DNS. For Dynamic IP addresses this service is enhanced with "DynamicDNS". This permits the use of a network component with a dynamic IP address as a Server on the Internet. DynDNS ensures that a service can always be addressed on the Internet at the same Domain name, regardless of the current IP address.EECT Explicit Call TransferParticipant A calls participant B. The participant puts the connection on hold and calls participant C. Rather than connect everyone in a three-party confer-ence, A now transfers participant B to C and hangs up.EEPROM  Electrically Erasable Programmable Read Only MemoryMemory building block in your phone with fixed data (e.g. default and custom-ized settings) and data saved automatically (e.g. entries to the list of callers).Ethernet networkWired LAN.FFirewall You can use a firewall to protect your network against unauthorized external access. This involves combining various measures and technologies (hard and/or software) to control the flow of data between a private network you wish to protect and an unprotected network (e.g., the Internet).  £NAT.Firmware Software for a device in which basic information is stored for the device's func-tion. To correct errors or update the device software, a new version of the firmware can be loaded into the device's memory (firmware update).Flat rate Billing system for an Internet connection. The Internet provider charges a set monthly fee. There are no additional charges for the duration of the connection or number of connections.FragmentationData packets that are too big are split into smaller packets (fragments) before they are transferred. They are put together again when they reach the recipient (defragmented).
176GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008Full duplex Data transmission is a mode in which data can be sent and received at the same time.GG.711 a law, G.711 µ law Standard for a Codec. G.711 delivers a very good voice quality that corresponds to that in the ISDN fixed line. As there is little compression, the necessary bandwidth is around 64 kbit/s per voice connection, but the delay caused by coding/decoding is only 0.125 ms. "a law" describes the European standard and "µ law" describes the North Amer-ican/Japanese equivalent. G.722 Standard for a Codec. G.722 is a broadband language codec with a bandwidth of 50 Hz to 7 kHz, a net transmission rate of 64 kbit/s per language connection and integrated speech pause recognition and comfort noise generation (silence suppression). G.722 delivers very good voice quality. A higher sampling rate provides clearer and better voice quality than other codecs and enables a speech tone in High Definition Sound Performance (HDSP). G.726 Standard for a Codec. G.726 delivers a good voice quality. It is inferior to the quality with codec G.711 but better than with G.729. G.729A/B Standard for a Codec. The voice quality is more likely to be lower with G.729A/B. As a result of the high level of compression, the necessary bandwidth is only around 8 kbit/s per voice connection, but the delay is around 15 ms. Gateway Connects two different Networks, e.g. a router as an Internet gateway. For phone calls from VoIP to the telephone network, a gateway has to be con-nected to the IP network and the telephone network (gateway/VoIP provider). It forwards calls from VoIP to the telephone network as required.Gateway provider £SIP provider. Global IP address £IP address.GSM  Global System for Mobile CommunicationOriginally, a European standard for mobile networks. GSM can now be described as a worldwide standard. In the USA and Japan national standards are now more frequently supported than in the past.
177GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008HHeadset Combination of microphone and headphone. A headset makes handsfree talk-ing more convenient. There are headsets available that can be connected to the handset by a cable.HTTP ProxyServer via which the Network subscribers can process their Internet traffic. Hub Uses one Infrastructure network to connect several Network subscribers. All data sent to the hub by one network subscriber is forwarded to all network subscribers. £Gateway, Router. IIEEE  Institute of Electrical and Electronics Engineers International body that defines standards in electronics and electro-technol-ogy, concerned in particular with the standardization of LAN technology, trans-mission protocols, data transfer rate and wiring.Infrastructure networkNetwork with central structure: All Network subscribers communicate via a central Router. Instant messaging Service that uses a client program to allow chatting in real time, i.e. to send brief messages to other subscribers on the Internet.Internet Global WAN. A series of protocols have been defined for exchanging data, known by the name TCP/IP. Each Network subscriber is identifiable via his IP address. DNS assigns a Domain name to the IP address. Important services on the Internet include the World Wide Web (WWW), e-mail, file transfer and discussion forums. Internet Service ProviderEnables access to the Internet for a fee.IP (Internet Protocol)TCP/IP protocol on the Internet. IP is responsible for addressing subscribers in a Network using IP addresses and transfers data from the sender to the recip-ient. IP determines the paths (routing) along which the data packets travel.
178GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008IP address A unique address for a network component within a network based on the TCP/IP protocols (e.g. LAN, Internet). On the Internet, domain names are usually assigned instead of IP addresses. DNS assigns the corresponding IP address to the domain name.The IP address consists of four three-digit decimal numbers separated from one another by a period (e.g. 223.94.233.2). The first decimal number can be between 1 and 126 and between 128 and 223, the second and third between 0 and 255, and the fourth between 1 and 254. The IP address is made up of the network number and the number of the Net-work subscriber (e.g. phone). Depending on the Subnet mask, the front one, two or three parts make up the network number and the rest of the IP address addresses the network component. The network number of all the components in any one network must be identical.IP addresses can be assigned automatically with DHCP (dynamic IP addresses) or manually (static IP addresses). £DHCP.IP pool rangeRange of IP addresses that the DHCP server can use to assign dynamic IP addresses.LLAN  Local Area NetworkNetwork with a restricted physical range. A LAN can be wireless (WLAN) and/or wired.Local IP addressThe local or private IP address is the address for a network component in the local network (LAN). The network operator can assign any address he or she wants. Devices that act as a link from a local network to the Internet (gateway or router) have a public and a private IP address. £IP address.Local SIP Port £SIP port/Local SIP port. MMAC address Media Access Control AddressHardware address by means of which each network device (e.g. network card, switch, phone) can be uniquely identified worldwide. It consists of 6 parts (hexadecimal numbers) separated by a "-" (e.g. 00-90-65-44-00-3A).The MAC address is assigned by the manufacturer and cannot be changed. Mbps  Million bits per secondUnit of the transmission speed in a network.
179GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008MRU  Maximum Receive UnitDefines the maximum user data volume within a data packet.MTU  Maximum Transmission UnitDefines the maximum length of a data packet that can be carried over the net-work at a time.Music on holdMusic that is played while you are on a Consultation call or Toggling. The waiting participant hears music while on hold.NNAT  Network Address TranslationMethod for converting (private) IP addresses to one or more (public) IP addresses. NAT enables the IP addresses of Network subscribers (e.g. VoIP tel-ephones) in a LAN to be concealed behind a shared IP address for the Router on the Internet.VoIP telephones behind a NAT router cannot be reached by VoIP servers (on account of the private IP address). To "get around" NAT, it is possible to use (alternately) ALG in the router, STUN in the VoIP telephone, or for the VoIP pro-vider to use an Outbound proxy. If an outbound proxy is made available you must allow for this in the VoIP set-tings for your phone.Network Group of devices. Devices can be connected in either wired or wireless mode. Networks can also differ in range and structure: uRange: local networks (LAN) or wide-area networks (WAN)uStructure: Infrastructure network or ad-hoc network Network subscriberDevices and PCs that are connected to each other in a network, e.g. servers, PCs and phones.OOutbound proxyAlternate NAT control mechanism to STUN and ALG. Outbound proxies are implemented by the VoIP provider in firewall/NAT envi-ronments as an alternate to SIP proxy server. They control data traffic through the firewall. Outbound proxy and STUN servers should not be used simultaneously.  £STUN and NAT.
180GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008PPaging (handset search)A base station function to locate registered handsets. The base station estab-lishes a connection to every registered handset. The handsets start to ring. Paging is activated by briefly pressing the button on the base station and is deactivated by briefly pressing the same button again. PIN  Personal Identification NumberProtects against unauthorized use. When the PIN is activated, a number combi-nation has to be entered to access a protected area. You can protect your base station configuration data with a system PIN (4-digit number combination).Port Data is exchanged between two applications in a Network via a port. Port forwardingThe Internet gateway (e.g. your router) forwards data packets from the Inter-net that are directed to a certain Port to the port concerned. This allows servers in the LAN to offer services on the Internet without you needing a public IP address.Port numberIndicates a specific application of a Network subscriber. Depending on the set-ting in the LAN, the port number is permanently assigned or else it is newly assigned with each access.The combination of IP address/Port number uniquely identifies the recipient or sender of a data packet within a network. Predialing   £Block dialing.Private IP address £Public IP address.Protocol Describes the agreements for communicating within a Network. It contains rules for opening, administering and closing a connection, about data formats, time frames and possible error handling.Proxy/Proxy serverComputer program that controls the exchange of data between Client and Server in computer networks. If the phone sends a query to the VoIP server, the proxy acts as a server towards the phone and as a client towards the server. A proxy is addressed via Domain names/IP addresses and Ports. Public IP addressThe public IP address is the address for a network component on the Internet. It is assigned by the Internet Service Provider. Devices that act as a link from a local network to the Internet (gateway, router) have a public and a local IP address. £IP address and NAT
181GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008QQuality of Service (QoS)Quality of serviceDescribes the Quality of Service in communication networks. Differentiations are made between various Quality of Service classes. QoS influences the flow of data packets on the Internet, e.g. by prioritizing data packets, reserving bandwidth and data packet optimization. In VoIP networks, QoS influences the voice quality. If the whole infrastructure (router, network server, etc.) has QoS, the voice quality is better, i.e. fewer delays, less echoing, less crackling. RRAM  Random Access MemoryMemory in which you have reading and storage rights. Items such as melodies and screen pictures are saved in the RAM after you have loaded them onto the phone via the Web configurator.Registrar The registrar manages the Network subscribers' current IP addresses. When you register with your VoIP provider, your current IP address is saved on the reg-istrar. This means you can also be reached when on the move. ROM  Read Only MemoryA type of memory that can only be read.Router Routes data packets within a network and between different networks via the quickest route. Can connect Ethernet networks and WLAN. Can be a Gateway to the Internet. Routing Routing is the transfer of data packets to another subscriber in your network. On their way to the recipient, the data packets are sent from one router to the next until they reach their destination.If data packets were not forwarded in this way, a network like the Internet would not be possible. Routing connects the individual networks to this global system.A router is a part of this system; it transfers data packets both within a local net-work and from one network to the next. Transfer of data from one network to another is performed on the basis of a common protocol.RTP  Realtime Transport ProtocolGlobal standard for transferring audio and video data. Often used in conjunc-tion with UDP. In this case, RTP packets are embedded in UDP packets.RTP port (Local) Port that is used to send and receive voice data packets for VoIP.Ringback when the number is busy= CCBS (Completion of Calls to Busy Subscriber). If a caller hears the busy tone, he or she can activate the ringback function. As soon as the connection is free the caller is rung back. As soon as the caller lifts the receiver the connection is made automatically.
182GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008Ringback when the call is not answered= CCNR (Completion of Calls on No Reply). If a participant does not respond when called, a caller can arrange an automatic ringback. As soon as the desti-nation phone has completed a call and is free again, the caller is rung back. This feature must be supported by the exchange. The ringback request is automat-ically canceled after about 2 hours (depending on the VoIP provider).SServer Provides a service to other Network subscribers (Clients). The term can indi-cate a computer/PC or an application. A server is addressed via IP addresses/Domain names and Ports. SIP (Session Initiation Protocol)Signaling protocol independent of voice communication. Used for establishing and ending a call. It is also possible to define parameters for voice transmission.SIP address  £URI.SIP port/Local SIP port(Local) Port that is used to send and receive SIP signaling data for VoIP.SIP provider  £VoIP provider.SIP proxy serverIP address of your VoIP provider's gateway server. Static IP addressA static IP address is assigned to a network component manually during net-work configuration. Unlike a Dynamic IP address, a static IP address does not change.STUN  Simple Transversal of UDP over NATNAT control mechanism. STUN is a data protocol for VoIP telephones. STUN replaces the private IP address in the data packets of the VoIP telephone with the public address of the secure private network. To control data transfer, a STUN server is also required on the Internet. STUN cannot be implemented with symmetric NATs.  £ALG, Firewall, NAT, Outbound proxy. Subnet Segment of a Network.Subnet mask IP addresses consist of a fixed network number and a variable subscriber number. The network number is identical for all Network subscribers. The size of the network number part is determined in the subnet mask. In the subnet mask 255.255.255.0, for example, the first three parts of the IP address are the network number and the last part the subscriber number.
183GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008Symmetric NATA symmetric NAT assigns different external IP addresses and port numbers to the same internal IP addresses and port numbers – depending on the external target address. TTCP  Transmission Control ProtocolTransport protocol. Session-based transmission protocol: it sets up, monitors and terminates a connection between sender and recipient for transporting data. TLS  Transport Layer SecurityProtocol for encrypting data transmissions on the Internet. TLS is a superordi-nated Transport protocol. Toggling Toggling allows you to switch between two callers or between a conference call and an individual caller without allowing the waiting caller to listen to the call.Transmission rateSpeed at which data is transmitted in the WAN or LAN. The transmission rate is measured in data units per unit of time (Mbit/s).Transport protocolControls data transport between two communication partners (applications).  £UDP, TCP, TLS. UUDP  User Datagram ProtocolTransport protocol. Unlike TCP, UDP is a non session-based protocol. UDP does not establish a fixed connection. The data packets ("datagrams") are sent as a broadcast. The recipient is solely responsible for making sure the data is received. The sender is not notified about whether it is received or not. URI  Uniform Resource IdentifierCharacter sequence for identifying resources (e.g. e-mail recipient, http://gigaset.com, files). On the Internet, URIs are used as a uniform identification for resources. URIs are also described as SIP addresses. URIs can be entered in the phone as a number. By dialing a URI you can call an Internet subscriber with VoIP equipment.URL  Universal Resource LocatorGlobally unique address of a domain on the Internet.A URL is a subtype of URI. URLs identify a resource by its location on the Inter-net. For historical reasons the term is often used as a synonym for URI. User ID  £User identification.
184GlossaryGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 24.04.2009Version 8, 03.09.2008User identificationName/number combination for access, e.g. to your VoIP account.VVoice codec  £Codec. VoIP  Voice over Internet Protocol Telephone calls are no longer placed and transmitted over the telephone network but over the Internet (or other IP networks).VoIP providerA VoIP, SIP or Gateway provider is an Internet service provider that provides a Gateway for Internet telephony. As the phone works with the SIP standard, your provider must support the SIP standard. The provider routes calls from VoIP to the telephone network (analog, ISDN and cellular) and vice versa.WWAN  Wide Area NetworkWide-area network that is unrestricted in terms of area (e.g. Internet).
185IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008IndexAAccess code (PABX)  . . . . . . . . . . . . . . 94Access protection. . . . . . . . . . . . . . . . 84Access to Web configuratorfrom other networks . . . . . . . . . 104Accessories . . . . . . . . . . . . . . . . . . . 171Account name (e-mail). . . . . . . . . . . 132Acknowledge tones . . . . . . . . . . . . . . 82Activatingadvisory tones  . . . . . . . . . . . . . . . . 82Annex B for G.729  . . . . . . . . . . . . 118auto answer . . . . . . . . . . . . . . . . . . 80handset . . . . . . . . . . . . . . . . . . . 1, 32keypad lock  . . . . . . . . . . . . . . . . . . 32network mailbox. . . . . . . . . . . . . . 125speaker  . . . . . . . . . . . . . . . . . . . . . 44Address assignment (IP address) . . . . 103ADSL . . . . . . . . . . . . . . . . . . . . . . . . 172Advisory tones. . . . . . . . . . . . . . . . . . 82Alarm clock . . . . . . . . . . . . . . . . . . . . 70Alarm repeat . . . . . . . . . . . . . . . . . . . 70ALG. . . . . . . . . . . . . . . . . . . . . . . . . 172Alternate DNS server (Web configurator)  . . . . . . . . . . 104Anonymous calling  . . . . . . . . . . . . . . 52Application Layer Gateway (ALG)  . . . 172Application signal (Flash key) . . . . . . 127Application type (Flash key) . . . . . . . 127Arabic characters, entering. . . . . . . . 100Area codedialing automatically. . . . . . . . . . . 122entering own . . . . . . . . . . . . . . . . 122Area code predialingactivating/deactivating . . . . . . . . . 122Area codes. . . . . . . . . . . . . . . . . . . . . 87extra area codes . . . . . . . . . . . . . . . 87extra codes. . . . . . . . . . . . . . . . . . . 87local area code . . . . . . . . . . . . . . . . 87own area code . . . . . . . . . . . . . . . . 87Assigning send number to handset . . 120Asterisk key . . . . . . . . . . . . . . . . . . 1, 82Asymmetric Digital Subscriber Line . . 172Audio (DTMF signaling) . . . . . . . . . . 126Authentication. . . . . . . . . . . . . . . . . 172Authentication namee-mail  . . . . . . . . . . . . . . . . . . . . . 132Auto answer . . . . . . . . . . . . . . . . . . . 41activating/deactivating. . . . . . . . . . 80Automatic configurationof a VoIP connection  . . . . . . . . . .  108Automatic version check . . . . . . . . .  138Available codecs . . . . . . . . . . . . . . .  117BBase stationactivating/deactivating eco mode . .  69changing system PIN . . . . . . . . . . .  84checking service information . . . .  148connecting  . . . . . . . . . . . . . . . . . . 18connecting to electrical power supply. . . . . . . . . . . . . . . . . . .  19connecting to fixed line network  . .  19connecting to router  . . . . . . . . . . .  20operating on PABX . . . . . . . . . . . . .  94power consumption. . . . . . . . . . .  151reducing power consumption. . . . .  69reducing transmission power . . . . .  69restoring factory settings . . . . . . . .  85setting  . . . . . . . . . . . . . . . . . . . . . 84setting default connection . . .  86, 119setting up . . . . . . . . . . . . . . . . . . .  17system PIN  . . . . . . . . . . . . . . . . . .  84updating firmware. . . . . . . . .  87, 137wall mounting . . . . . . . . . . . . . . .  195Base station power consumptionreducing . . . . . . . . . . . . . . . . . . . .  69Batterycharge status. . . . . . . . . . . . . . . . . . 2charging . . . . . . . . . . . . . . . . . .  1, 14display  . . . . . . . . . . . . . . . . . . .  1, 14icon  . . . . . . . . . . . . . . . . . . . . .  1, 14inserting . . . . . . . . . . . . . . . . . . . .  11recommended batteries . . . . . . . .  150tone  . . . . . . . . . . . . . . . . . . . . . . .  83Block dialing . . . . . . . . . . . . . . . . . .  172Blocking your caller ID. . . . . . . . . . . .  52Broadband connections. . . . . . . . . . . . 9Broadband Internet access. . . . . . . .  172Broadband voice codec . . . . . .  115, 176Buddy. . . . . . . . . . . . . . . . . . . . . . .  172Buttons (Web configurator) . . . . . . .  101
186IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008CCallaccepting . . . . . . . . . . . . . . . . . . . . 41disconnecting (toggling) . . . . . . . . . 55ending . . . . . . . . . . . . . . . . . . . . . . 41external . . . . . . . . . . . . . . . . . . . . . 43incoming . . . . . . . . . . . . . . . . . . . . . 2internal  . . . . . . . . . . . . . . . . . . . . . 74number/name display . . . . . . . . . . . 42rejecting external . . . . . . . . . . . . . . 76transferring (connecting)  . . . . . . . . 75Call acceptanceautomatic. . . . . . . . . . . . . . . . . . . . 80Call display  . . . . . . . . . . . . . . . . . . . . 42fixed line network. . . . . . . . . . . . . . 42VoIP . . . . . . . . . . . . . . . . . . . . . . . . 42Call duration . . . . . . . . . . . . . . . . . . . 46Call forwarding  . . . . . . . . . . . . . . . . 173Gigaset.net. . . . . . . . . . . . . . . 53, 121VoIP (handset) . . . . . . . . . . . . . . . . 53VoIP (Web configurator) . . . . . . . . 121Call waiting . . . . . . . . . . . . . . . 172, 173accepting/rejecting (VoIP) . . . . . . . . 56activating/deactivating (VoIP)  . . . . . 54internal call  . . . . . . . . . . . . . . . . . . 76Caller ID  . . . . . . . . . . . . . . . . . . . . . . 42Callinganonymously . . . . . . . . . . . . . . . . . 52entering IP address . . . . . . . . . . . . . 40external . . . . . . . . . . . . . . . . . . . . . 38Gigaset.net. . . . . . . . . . . . . . . . 49, 51internal  . . . . . . . . . . . . . . . . . . . . . 74via VoIP/fixed line network  . . . . . . . 38Calls list. . . . . . . . . . . . . . . . . . . . . . . 58Cancelingdialing . . . . . . . . . . . . . . . . . . . . . . 40operation . . . . . . . . . . . . . . . . . . . 101Care of the telephone  . . . . . . . . . . . 150CF . . . . . . . . . . . . . . . . . . . . . . . . . . 173Changingdialing mode  . . . . . . . . . . . . . . . . . 94earpiece volume . . . . . . . . . . . . . . . 80handsfree volume. . . . . . . . . . . . . . 80internal number . . . . . . . . . . . 73, 133system PIN . . . . . . . . . . . . . . . . . . . 84to daylight saving time . . . . . . . . . 139Charge status display (battery) . . . . 1, 14Charge status of the batteries. . . . . . . . 2Charging cradleconnecting  . . . . . . . . . . . . . . . . . . 13wall mounting . . . . . . . . . . . . . . .  195Chatting . . . . . . . . . . . . . . . . . . . . .  173Checking EEPROM version . . . . . . . .  140Checking service information  . . . . .  148Client . . . . . . . . . . . . . . . . . . . . . . .  173Codecs . . . . . . . . . . . . . . . . . . . . . .  173Codecs, available  . . . . . . . . . . . . . .  117COLP  . . . . . . . . . . . . . . . . . . . .  44, 173COLR  . . . . . . . . . . . . . . . . . . . .  44, 173Conference. . . . . . . . . . . . . . . . . . . .  76Conference callfixed line network . . . . . . . . . . . . .  53VoIP  . . . . . . . . . . . . . . . . . . . . . . .  55Configurationvia PC . . . . . . . . . . . . . . . . . . . . . .  96VoIP connection (automatic)  . . . .  108ConfiguringVoIP connection (handset) . . . . . . .  90VoIP connection (Web config.) . . .  106Confirmation tone. . . . . . . . . . . . . . . 82Connected Line Identification Presentation  .  44, 173ConnectingPC to the Web configurator. . . .  96, 97phone to internal company network . . . . . . . . . . . . . . . .  105Connectionactivating (VoIP)  . . . . . . . . . . . . .  114Internet (troubleshooting) . . . . . . .  27name/provider (Web config.) . . . .  106phone to an internal company network . . . . . . . . . . . . . . . .  105selecting (line suffix) . . . . . . . .  38, 39to Gigaset.net . . . . . . . . . . . . . . .  114Connection namefixed line network . . . . . . . . . . . .  114VoIP  . . . . . . . . . . . . . . . . . . . . . .  108Connection typeselecting (Display key) . . . . . . .  38, 39selecting (Talk key). . . . . . . . . . . . .  38Connection wizardstarting (getting started) . . . . . . . .  21Consultation call . . . . . . . . . . . . . . .  173ending  . . . . . . . . . . . . . . . . . . . . .  76external (fixed line network)  . . . . .  53external (VoIP). . . . . . . . . . . . . . . .  55internal . . . . . . . . . . . . . . . . . . . . . 75Control key . . . . . . . . . . . . . . . . . .  1, 30
187IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008Correcting incorrect entries  . . . . . . . . 31Cost control. . . . . . . . . . . . . . . . . . 8, 45defining dialing plans . . . . . . . . . . 123Customer Care. . . . . . . . . . . . . 141, 159Customer Service. . . . . . . . . . . . . . . 141CW . . . . . . . . . . . . . . . . . . . . . . . . . 173Cyrillic characters, entering  . . . . . . . 100DData packets, fragmentation. . . . . . . 175Data server for firmware update . . . . 137Dateset manually. . . . . . . . . . . . . . . . . . 14transferring from time server  . . . . 139Daylight saving timechanging automatically. . . . . . . . . 139Deactivatingadvisory tones  . . . . . . . . . . . . . . . . 82auto answer . . . . . . . . . . . . . . . . . . 80handset . . . . . . . . . . . . . . . . . . . 1, 32keypad lock  . . . . . . . . . . . . . . . . . . 32network mailbox. . . . . . . . . . . . . . 125speaker  . . . . . . . . . . . . . . . . . . . . . 44Default gatewayentering (handset) . . . . . . . . . . . . . 92entering (Web configurator) . . . . . 103Default settingshandset . . . . . . . . . . . . . . . . . . . . . 83Delete key . . . . . . . . . . . . . . . . . . . . . 30Deleting characters  . . . . . . . . . . . . . . 31Demilitarized Zone. . . . . . . . . . . . . . 174De-registeringfrom Web configurator . . . . . . . . . . 98handset from base station. . . . . . . . 72DHCP. . . . . . . . . . . . . . . . . . . . 174, 175Dialingcanceling . . . . . . . . . . . . . . . . . . . . 40directory  . . . . . . . . . . . . . . . . . . . . 63IP address. . . . . . . . . . . . . . . . . . . . 40using shortcuts. . . . . . . . . . . . . . . . 64Dialing mode . . . . . . . . . . . . . . . . . . . 94Dialing plans . . . . . . . . . . . . . 8, 45, 123activating/deactivating . . . . . . . . . 124defining . . . . . . . . . . . . . . . . . . . . 123deleting . . . . . . . . . . . . . . . . . . . . 125for emergency numbers . . . . . . . . 125Differentiated Service Code Point . . . 174Digit keychanging assignment . . . . . . . . . . . 79Digital clock. . . . . . . . . . . . . . . . . . . . 78Digital Subscriber Line. . . . . . . . . . .  174Digital Subscriber LineAccess Multiplexer . . . . . . . . . .  174Directory  . . . . . . . . . . . . . . . . . . . . .  62copying number  . . . . . . . . . . . . . . 65copying number from text . . . . . . .  65deleting (Web configurator) . . . . .  136editing via PC. . . . . . . . . . . . . . . .  134Gigaset.net . . . . . . . . . . . . . . . . . .  48loading from PC . . . . . . . . . . . . . .  135managing entries. . . . . . . . . . . . . .  64opening  . . . . . . . . . . . . . . . . . . . . 30order of entries . . . . . . . . . . . . . . .  63saving entry  . . . . . . . . . . . . . . . . .  63saving the first number  . . . . . . . . .  62sending entry/list to handset  . . . . .  65transferring to/from PC. . . . . . . . .  134Directory filecontent (vCard format)  . . . . . . . .  136Displayappointment/alarm activated . . . . . .  2call duration  . . . . . . . . . . . . . . . . .  46call duration/costs . . . . . . . . . . . . .  46caller’s number (CID) . . . . . . . . . . . 42changing display language. . . . . . .  77charge status of the batteries . . . . . . 2in idle status . . . . . . . . . . . . . . .  1, 32incoming call. . . . . . . . . . . . . . . . . .  2keypad lock . . . . . . . . . . . . . . . . . . .  2name (CID) . . . . . . . . . . . . . . . . . . 43ringer melody deactivated . . . . . . . .  2screensaver . . . . . . . . . . . . . . . . . . 78Display keys  . . . . . . . . . . . . . . . . .  1, 30assigning. . . . . . . . . . . . . . . . . . . .  79changing assignment. . . . . . . . . . .  79Displayed name (VoIP). . . . . . .  110, 174Disposal . . . . . . . . . . . . . . . . . . . . .  149DMZ. . . . . . . . . . . . . . . . . . . . . . . .  174DNS . . . . . . . . . . . . . . . . . . . . . . . .  174DNS server . . . . . . . . . . . . . . . . . . . .  92alternate (Web configurator)  . . . .  104preferred (handset) . . . . . . . . . . . .  92preferred (Web configurator) . . . .  104Domain  . . . . . . . . . . . . . . . . . . . . . 111Domain name. . . . . . . . . . . . . . . . .  174Domain Name System. . . . . . . . . . .  174DSCP  . . . . . . . . . . . . . . . . . . . . . . . 174DSL  . . . . . . . . . . . . . . . . . . . . . . . .  174DSLAM . . . . . . . . . . . . . . . . . . . . . .  174DTMF (tone dialing)  . . . . . . . . . . . . .  95
188IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008DTMF signaling for VoIP . . . . . . . . . . 126Dynamic DNS. . . . . . . . . . . . . . . . . . 175Dynamic Host ConfigurationProtocol  . . . . . . . . . . . . . . . . . . 174Dynamic IP address  . . . . . . . . . 103, 175DynDNS. . . . . . . . . . . . . . . . . . . . . . 175EEarpiece mode. . . . . . . . . . . . . . . . . . 44Earpiece volume  . . . . . . . . . . . . . . . . 80Echo serviceGigaset.net. . . . . . . . . . . . . . . . . . . 46ECO DECT  . . . . . . . . . . . . . . . . . . . . . 69Eco mode  . . . . . . . . . . . . . . . . . . . . . 69E-mailaccount name  . . . . . . . . . . . . . . . 132authentication name/password . . . 132entering access data . . . . . . . . . . . 132incoming e-mail server . . . . . . . . . 132settings (Web config.). . . . . . . . . . 132Emergency numbersdialing . . . . . . . . . . . . . . . . . . . . . . 40dialing plans for . . . . . . . . . . . . . . 125End Call key . . . . . . . . . . . . . . . 1, 40, 41Ending, call . . . . . . . . . . . . . . . . . . . . 41Enteringaccess data (e-mail)  . . . . . . . . . . . 132flash  . . . . . . . . . . . . . . . . . . . . . . . . 1user data . . . . . . . . . . . . . . . . . . . . 24Entering Cyrillic/Arabiccharacters . . . . . . . . . . . . . . . . . 100Entryselecting from directory  . . . . . . . . . 63Error tone . . . . . . . . . . . . . . . . . . . . . 82Ethernet network. . . . . . . . . . . . . . . 175Explicit Call Transfer . . . . . . . . . . . . . 175External consultation callfixed line network. . . . . . . . . . . . . . 53VoIP . . . . . . . . . . . . . . . . . . . . . . . . 55External line prefix (PABX)  . . . . . . . . . 94Extra area codes. . . . . . . . . . . . . . . . . 87Extra codes . . . . . . . . . . . . . . . . . . . . 87FFactory settingsbase station . . . . . . . . . . . . . . . . . . 85Fast access. . . . . . . . . . . . . . . . . . . . . 66Firewall . . . . . . . . . . . . . . . . . . . . . . 175Firmware  . . . . . . . . . . . . . . . . . . . .  175automatic update  . . . . . . . . .  88, 138checking version . . . . . . . . .  140, 148starting update (handset). . . . . . . .  87starting update (Web conf.) . . . . .  137updates. . . . . . . . . . . . . . . . . . . . . 11Fixed line networkconference call  . . . . . . . . . . . . . . . 53connection name. . . . . . . . . . . . .  114external consultation call . . . . . . . . 53settings for calls. . . . . . . . . . . . . . .  53Fixed line network connectionline suffix  . . . . . . . . . . . . . . . . . .  107Flash key  . . . . . . . . . . . . . . . . . . . . . . 1function for VoIP . . . . . . . . . . . . .  127Flat rate . . . . . . . . . . . . . . . . . . . . .  175Fragmentation of data packets. . . . .  175Free software, licenses  . . . . . . . . . .  163Full duplex . . . . . . . . . . . . . . . . . . .  176GG.711 µ law . . . . . . . . . . . . . . . . . .  116G.711 a law  . . . . . . . . . . . . . . . . . .  116G.722. . . . . . . . . . . . . . . . . . . . .  9, 115G.722 Broadband language codec . .  115G.726. . . . . . . . . . . . . . . . . . . . . . .  116G.729. . . . . . . . . . . . . . . . . . . . . . .  116Gateway . . . . . . . . . . . . . . . . . . . . .  176Gateway provider . . . . . . . . . . . . . .  176Getting help with your phone . . . . .  141Gigaset config. . . . . . . . . . . . . . .  96, 97Gigaset HDSP, see HDSPGigaset.net. . . . . . . . . . . . . . . . . . . . 46(de)activating connection  . . . . . .  114call forwarding  . . . . . . . . . . .  53, 121calling participant  . . . . . . . . . .  49, 51changing/deleting own name. . . . .  50directory . . . . . . . . . . . . . . . . . . . .  48Echo service  . . . . . . . . . . . . . . . . . 46entering name. . . . . . . . . . . . .  47, 50Jabber server. . . . . . . . . . . . . . . .  131messaging. . . . . . . . . . . . . . . . . .  131searching for subscriber . . . . . . . . .  48Gigaset.net directoryopen . . . . . . . . . . . . . . . . . . . . . . . 30specifying/editing own name . . . . . 50Global IP address. . . . . . . . . . . . . . .  176Global System forMobile Communication. . . . . . .  176GNU Lesser General Public License. .  163
189IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008Group call . . . . . . . . . . . . . . . . . . . . . 74GSM . . . . . . . . . . . . . . . . . . . . . . . . 176HHandsetactivating/deactivating . . . . . . . . 1, 32activating/deactivating advisory tones . . . . . . . . . . . . . . . . . . . . 82assigning receive number . . . . . . . 120assigning send number. . . . . . . . . 120changing internal names. . . . . 74, 133changing internal number. . . . 73, 133changing name  . . . . . . . . . . . 74, 133checking service information. . . . . 148contact with liquid . . . . . . . . . . . . 150de-registering. . . . . . . . . . . . . . . . . 72display language. . . . . . . . . . . . . . . 77diverting a call . . . . . . . . . . . . . . . . 75earpiece volume . . . . . . . . . . . . . . . 80handsfree volume. . . . . . . . . . . . . . 80idle status  . . . . . . . . . . . . . . . . . . . 32locating . . . . . . . . . . . . . . . . . . . . . 73muting. . . . . . . . . . . . . . . . . . . . . . 45registering . . . . . . . . . . . . . . . . 16, 71restoring to factory settings. . . . . . . 83setting (individual) . . . . . . . . . . . . . 77setting up. . . . . . . . . . . . . . . . . . . . 11using several  . . . . . . . . . . . . . . . . . 71Handset directory, see DirectoryHDSP. . . . . . . . . . . . . . . . . . . . 8, 9, 115Headset. . . . . . . . . . . . . . . . . . . . . . 177Hearing aids  . . . . . . . . . . . . . . . . . . . . 7High Definition Sound Performance, see HDSPHTTP Proxy  . . . . . . . . . . . . . . . 105, 177Hub. . . . . . . . . . . . . . . . . . . . . . . . . 177IIcondisplay . . . . . . . . . . . . . . . . . . . . . . 30for new messages . . . . . . . . . . . . . . 58Idle statusdisplay . . . . . . . . . . . . . . . . . . . . 1, 32returning to . . . . . . . . . . . . . . . . . . 32IEEE. . . . . . . . . . . . . . . . . . . . . . . . . 177Incoming e-mail server (e-mail)  . . . . 132Incorrect input (correction). . . . . . . . . 31Info services  . . . . . . . . . . . . . . . . . . 133configuring  . . . . . . . . . . . . . . . . . 133Infrastructure network . . . . . . . . . . . 177Installing, base station  . . . . . . . . . . .  17Instant messaging. . . . . . . . . .  130, 177Institute of Electrical and Electronics Engineers . . . . . . . .  177Interface languagehandset. . . . . . . . . . . . . . . . . . . . .  77Web configurator. . . . . . . . . . . . . .  98Internal call. . . . . . . . . . . . . . . . . . . .  74call waiting . . . . . . . . . . . . . . . . . .  76Internal company network. . . . . . . .  105Internal consultation call . . . . . . . . . .  75Internal key. . . . . . . . . . . . . . . . . . . . . 1Internet  . . . . . . . . . . . . . . . . . . . . . 177no connection to . . . . . . . . . . . . . . 27Internet access (broadband)  . . . . . .  172Internet protocol . . . . . . . . . . . . . . .  177Internet Service Provider . . . . . . . . .  177Intranet  . . . . . . . . . . . . . . . . . . . . . 105IP . . . . . . . . . . . . . . . . . . . . . . . . . .  177IP address . . . . . . . . . . . . . . . . . . . .  178assigning (handset) . . . . . . . . . . . .  91assigning (Web configurator) . . . .  103checking (Web configurator)  . . . .  140dialing. . . . . . . . . . . . . . . . . . . . . .  40display on handset. . . . . . . . . . . . . .  2dynamic  . . . . . . . . . . . . . . . . . . .  175global . . . . . . . . . . . . . . . . . . . . .  176local . . . . . . . . . . . . . . . . . . . . . .  178obtaining automatically . . . . .  91, 103private  . . . . . . . . . . . . . . . . . . . . 180public . . . . . . . . . . . . . . . . . . . . .  180static. . . . . . . . . . . . . . . . . . . . . .  182IP address type . . . . . . . . . . . . . . . .  103IP configurationhandset. . . . . . . . . . . . . . . . . . . . .  91Web configurator. . . . . . . . . . . . .  103IP pool range  . . . . . . . . . . . . . . . . .  178JJabber ID (messenger). . . . . . . . . . .  131Jabber server (messenger). . . . . . . .  131Jabber server port (messenger) . . . .  131KKey 1 (fast access). . . . . . . . . . . . . . . .  1assigning. . . . . . . . . . . . . . . . . . . .  66Key click . . . . . . . . . . . . . . . . . . . . . .  82Keypad lock  . . . . . . . . . . . . . . . . . . .  32
190IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008Keysassigning directory entry. . . . . . . . . 64Asterisk key  . . . . . . . . . . . . . . . . 1, 82Control key. . . . . . . . . . . . . . . . . 1, 30Delete key  . . . . . . . . . . . . . . . . . . . 30delete key. . . . . . . . . . . . . . . . . . . . 30Display keys . . . . . . . . . . . . . . . . 1, 30End Call key . . . . . . . . . . . . . 1, 40, 41fast access . . . . . . . . . . . . . . . . . . . . 1Flash key  . . . . . . . . . . . . . . . . . . . . . 1Internal key  . . . . . . . . . . . . . . . . . . . 1keypad lock  . . . . . . . . . . . . . . . . . . 32Message key. . . . . . . . . . . . . . . . . . . 1On/Off key . . . . . . . . . . . . . . . . . . . . 1Paging key (base station)  . . . . . . . . . 2Pound key  . . . . . . . . . . . . . . . . . 1, 32Shortcut. . . . . . . . . . . . . . . . . . . . . 64Speaker key  . . . . . . . . . . . . . . . . . . . 1Talk key  . . . . . . . . . . . . . . . . . . . . . .1LLAN. . . . . . . . . . . . . . . . . . . . . . . . . 178Languagehandset . . . . . . . . . . . . . . . . . . . . . 77Web configurator . . . . . . . . . . . . . . 98Last number redial . . . . . . . . . . . . . . . 57LGPL . . . . . . . . . . . . . . . . . . . . . . . . 163Licenses, free software. . . . . . . . . . . 163Line suffixdialing with  . . . . . . . . . . . . . . . 38, 39display (Web configurator)  . . . . . . 107Line typefor outgoing calls . . . . . . . . . . . . . 119Liquid . . . . . . . . . . . . . . . . . . . . . . . 150ListCalls List. . . . . . . . . . . . . . . . . . . . . 58Missed Calls . . . . . . . . . . . . . . . 58, 60Network Mailbox  . . . . . . . . . . . 58, 67Local area code . . . . . . . . . . . . . . . . . 87Local Area Network  . . . . . . . . . . . . . 178Local communication ports  . . . . . . . 128Local IP address . . . . . . . . . . . . . . . . 178Local network . . . . . . . . . . . . . . . . . 103Local SIP port. . . . . . . . . . . . . . . . . . 182Lock (keypad lock) . . . . . . . . . . . . . . . 32Login passworde-mail  . . . . . . . . . . . . . . . . . . . . . 132messenger . . . . . . . . . . . . . . . . . . 131MMAC address. . . . . . . . . . . . . . . . . .  178checking (handset)  . . . . . . . . . . . .  93checking (Web configurator)  . . . .  140Mailboxdefining for fast access. . . . . . . . . .  66Main menu. . . . . . . . . . . . . . . . . . . .  34Making callsaccepting a call . . . . . . . . . . . . . . .  41cost-effective calls . . . . . . . . . . . . .  45external (VoIP, fixed line network). .  38internal . . . . . . . . . . . . . . . . . . . . .  74Maximum Receive Unit . . . . . . . . . .  179Maximum Transmission Unit . . . . . .  179Mbps . . . . . . . . . . . . . . . . . . . . . . .  178Media Access Control  . . . . . . . . . . .  178Medical appliances . . . . . . . . . . . . . . .  7Menuend tone . . . . . . . . . . . . . . . . . . . .  82phone overview. . . . . . . . . . . . . . . 34prompting . . . . . . . . . . . . . . . . . . . 31Web configurator overview  . . . . . . 37Menu bar (Web configurator)  . . . . . . 99Message key . . . . . . . . . . . . . . . . . . . .  1opening lists . . . . . . . . . . . . . . . . . 58Messageslistening to network mailbox  . . . . .  67MessagingGigaset.net . . . . . . . . . . . . . . . . .  131Messengeraccount. . . . . . . . . . . . . . . . . . . . 131entering access data  . . . . . . . . . .  130priority . . . . . . . . . . . . . . . . . . . .  130resource name. . . . . . . . . . . . . . .  130Microphone  . . . . . . . . . . . . . . . . . . . . 1Million bits per second  . . . . . . . . . .  178Missed calls  . . . . . . . . . . . . . . . .  58, 60MRU. . . . . . . . . . . . . . . . . . . . . . . .  179MTU . . . . . . . . . . . . . . . . . . . . . . . .  179Music on hold . . . . . . . . . . .  45, 86, 179Mutingmicrophone. . . . . . . . . . . . . . . . . .  45Muting the handset. . . . . . . . . . . . . .  45Muting the microphone. . . . . . . . . . . 45
191IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008NNamechanging name of the handset . . . . . . . . . . . . . . 74, 133displayed (VoIP) . . . . . . . . . . . . . . 174displaying caller’s name (CID) . . . . . 43fixed line network connection . . . . 114NAT. . . . . . . . . . . . . . . . . . . . . . . . . 179symmetric  . . . . . . . . . . . . . . . . . . 183updating  . . . . . . . . . . . . . . . . . . . 113Navigation area (Web config.)  . . . . . 100Network  . . . . . . . . . . . . . . . . . . . . . 179Ethernet. . . . . . . . . . . . . . . . . . . . 175Network Address Translation  . . . . . . 179Network area. . . . . . . . . . . . . . . . . . 111Network mailbox . . . . . . . . . . . . . . . . 66activating/deactivating . . . . . . . . . 125calling . . . . . . . . . . . . . . . . . . . 67, 68defining for fast access . . . . . . . . . . 66entering number  . . . . . . . . . . . . . 125list . . . . . . . . . . . . . . . . . . . . . . . . . 67Network servicesfixed line network. . . . . . . . . . . . . . 52fixed line network and VoIP . . . . . . . 52settings for fixed line network calls . . . . . . . . . . . . . . 53settings for VoIP calls  . . . . . . . . 53, 55VoIP . . . . . . . . . . . . . . . . . . . . . . . . 53Numbercopying from directory . . . . . . . . . . 65copying to directory . . . . . . . . . . . . 65displaying caller’s number (CID)  . . . 42entering network mailbox number.125entering with directory . . . . . . . . . . 65saving in the directory. . . . . . . . . . . 63Number assignment. . . . . . . . . . . . . 120Number displaywithholding . . . . . . . . . . . . . . . . . . 52OOn/Off key. . . . . . . . . . . . . . . . . . . . . . 1Online directoryGigaset.net. . . . . . . . . . . . . . . . . . . 48Operation (preparing to use the phone) . . . . . . . . . . . . . . . . . 10Order in directory. . . . . . . . . . . . . . . . 63Outbound proxy. . . . . . . . . . . . 113, 179mode . . . . . . . . . . . . . . . . . . . . . . 113port . . . . . . . . . . . . . . . . . . . . . . . 113Own area codearea code  . . . . . . . . . . . . . . . . . . .  87entering  . . . . . . . . . . . . . . . . . . . 122PPABXaccess code (external line prefix). . . . . . . . . . . . . . . . . . . 94operating base station on PABX  . . .  94pauses  . . . . . . . . . . . . . . . . . . . . . 95setting dialing mode  . . . . . . . . . . .  94setting recall . . . . . . . . . . . . . . . . .  94Pack contents . . . . . . . . . . . . . . . . . .  10Paging . . . . . . . . . . . . . . . . .  2, 73, 180Pauses (PABX). . . . . . . . . . . . . . . . . .  95Personal Identification Number . . . .  180Personal provider data. . . . . . . . . . .  110Phoneconfiguring via PC . . . . . . . . . . . . .  96functions, overview . . . . . . . . . . . . 34menu overview . . . . . . . . . . . . . . .  34protecting . . . . . . . . . . . . . . . . . . . 84setting (Web configurator) . . . . . .  102setting base station (on handset) . .  84setting up . . . . . . . . . . . . . . . . . . .  10status (Web configurator). . . . . . .  140Phone number displaywithholding. . . . . . . . . . . . . . . . . .  52PIN . . . . . . . . . . . . . . . . . . . . . . . . .  180changing. . . . . . . . . . . . . . . . . . . .  84POP3 server  . . . . . . . . . . . . . . . . . .  132Port . . . . . . . . . . . . . . . . . . . . . . . .  180Port forwarding. . . . . . . . . . . . . . . .  180Port number . . . . . . . . . . . . . . . . . . 180Pound key. . . . . . . . . . . . . . . . . . .  1, 32Power adapter  . . . . . . . . . . . . . . . . . . 7Power consumption of base station .  151Predialing . . . . . . . . . . . . . . . . . . . .  180Preferred DNS serverentering (handset). . . . . . . . . . . . . 92entering (Web configurator). . . . .  104Priority (messenger) . . . . . . . . . . . .  130Private IP address  . . . . . . . . . . . . . .  180Protocol . . . . . . . . . . . . . . . . . . . . . 180Proxy . . . . . . . . . . . . . . . . . . . . . . .  180Proxy server address . . . . . . . . . . . .  111Proxy-Server . . . . . . . . . . . . . . . . . .  180Public IP address . . . . . . . . . . . . . . .  180
192IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008QQuality  . . . . . . . . . . . . . . . . . . . . . . 181Quality of Service. . . . . . . . . . . . . . . 181RRAM  . . . . . . . . . . . . . . . . . . . . . . . . 181Random Access Memory  . . . . . . . . . 181Read Only Memory  . . . . . . . . . . . . . 181Recall  . . . . . . . . . . . . . . . . . . . . . . . . 75Receive numberassigning to handset. . . . . . . . . . . 120display on the handset  . . . . . . . . . . 42Registeringhandset . . . . . . . . . . . . . . . . . . 16, 71with the Web configurator  . . . . . . . 98Registrar . . . . . . . . . . . . . . . . . . . . . 181Registrar server . . . . . . . . . . . . . . . . 111Registrar server port. . . . . . . . . . . . . 111Registration nameVoIP account  . . . . . . . . . . . . . . . . 110Registration passwordVoIP account  . . . . . . . . . . . . . . . . 110Registration refresh time . . . . . . . . . 111Remote access to Web configurator  . 104Remote management. . . . . . . . . . . . 104Resettingbase station . . . . . . . . . . . . . . . . . . 85handset . . . . . . . . . . . . . . . . . . . . . 83Resource name (messenger). . . . . . . 130RFC 2833 (DTMF signaling)  . . . . . . . 126Ringbackinitiating (fixed line network)  . . . . . 53when busy . . . . . . . . . . . . . . . . . . 181when the call is not answered . . . . 182Ringerdeactivating permanently . . . . . . . . 82icon . . . . . . . . . . . . . . . . . . . . . . . . . 2setting melody . . . . . . . . . . . . . . . . 81Ringer melodychanging . . . . . . . . . . . . . . . . . . . . 81muting. . . . . . . . . . . . . . . . . . . . . . 41setting volume . . . . . . . . . . . . . . . . 81ROM . . . . . . . . . . . . . . . . . . . . . . . . 181Router . . . . . . . . . . . . . . . . . . . . . . . 181connecting base station  . . . . . . . . . 20Routing . . . . . . . . . . . . . . . . . . . . . . 181RTP . . . . . . . . . . . . . . . . . . . . . . . . . 181RTP port  . . . . . . . . . . . . . . . . . 129, 181SSafety precautions  . . . . . . . . . . . . . . .  7Scope of delivery  . . . . . . . . . . . . . . .  10Screen protection, see ScreensaverScreensaver  . . . . . . . . . . . . . . . . . . . 78Search for subscriber on Gigaset.net  .  48Searchinghandset. . . . . . . . . . . . . . . . . . . . .  73in directory . . . . . . . . . . . . . . . . . .  63Sendingdirectory entry to handset  . . . . . . .  65Server  . . . . . . . . . . . . . . . . . . . . . . 182for firmware update. . . . . . . . . . .  137Server port . . . . . . . . . . . . . . . . . . .  111Service (Customer Care) . . . . . . . . .  159Settingbase station. . . . . . . . . . . . . . . . . .  84date  . . . . . . . . . . . . . . . . . . . . . . . 77date/time on handset. . . . . . . . . . .  14default connection. . . . . . . . .  86, 119handset. . . . . . . . . . . . . . . . . . . . .  77melody (ringer) . . . . . . . . . . . . . . .  81recall (PABX) . . . . . . . . . . . . . . . . . 94time . . . . . . . . . . . . . . . . . . . . . . .  77time zone . . . . . . . . . . . . . . . . . .  139wake-up time  . . . . . . . . . . . . . . . .  70Settings for VoIP telephony . . . . . . .  107Shortcut (digit combination) . . . . . . . 34Shortcuts . . . . . . . . . . . . . . . . . .  62, 64Signal strength . . . . . . . . . . . . . . . . . . 1Signal tone, see Advisory tonesSimple Transversal of UDP over NAT .  182SIP . . . . . . . . . . . . . . . . . . . . . . . . .  182SIP address . . . . . . . . . . . . . . . . . . .  182SIP Info (DTMF signaling). . . . . . . . .  126SIP port  . . . . . . . . . . . . . . . . .  129, 182SIP provider  . . . . . . . . . . . . . . . . . .  182SIP proxy server  . . . . . . . . . . . . . . .  182Snooze (alarm clock). . . . . . . . . . . . . 70Snooze mode (alarm clock) . . . . . . . .  70Sound, see Ringer melodySpeaker  . . . . . . . . . . . . . . . . . . . . . .  44activating/deactivating. . . . . . . . . . 44key . . . . . . . . . . . . . . . . . . . . . . . . .  1mode  . . . . . . . . . . . . . . . . . . . . . .  44Specifications . . . . . . . . . . . . . . . . .  150Starting connection wizard (menu)  . . . . . . . . . . . . . . . . . . .  89Static IP address  . . . . . . . .  91, 103, 182
193IndexGigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / Gigaset_A580_IPSIX.fm / 24.04.2009Version 8, 03.09.2008StatusVoIP connection . . . . . . . . . . . . . . 107Status codesactivating display (handset). . . . . . . 93activating display (Web config.). . . 136table (VoIP)  . . . . . . . . . . . . . . . . . 145Structure of IP address . . . . . . . . . . . 178STUN. . . . . . . . . . . . . . . . . . . . . . . . 182STUN port . . . . . . . . . . . . . . . . . . . . 112STUN refresh time . . . . . . . . . . . . . . 112STUN server. . . . . . . . . . . . . . . . . . . 112Subnet  . . . . . . . . . . . . . . . . . . . . . . 182Subnet mask . . . . . . . . . . . . . . . . . . 182defining (handset) . . . . . . . . . . . . . 92defining (Web configurator) . . . . . 103Suffix  . . . . . . . . . . . . . . . . . . . . . . . 107dialing with  . . . . . . . . . . . . . . . 38, 39Suppressingsilence . . . . . . . . . . . . . . . . . . . . . 118speech pauses  . . . . . . . . . . . . . . . 118speech pauses (VoIP)  . . . . . . . . . . 118Symmetric NAT  . . . . . . . . . . . . . . . . 183Synchronization with time server . . . 139System settings . . . . . . . . . . . . . . . . . 84TTalk key . . . . . . . . . . . . . . . . . . . . . . . . 1TCP . . . . . . . . . . . . . . . . . . . . . . . . . 183Telephone connectionconfiguring (Web config.) . . . . . . . 106Telephone jack pin connections  . . . . 152Telephone jack, pin connections . . . . 152Text informationin idle display mode  . . . . . . . . . . . 133Timeset manually. . . . . . . . . . . . . . . . . . 14transferring from time server  . . . . 139Time server . . . . . . . . . . . . . . . . . . . 139TLS . . . . . . . . . . . . . . . . . . . . . . . . . 183Toggling  . . . . . . . . . . . . . . . . . . . . . 183disconnecting call. . . . . . . . . . . . . . 55VoIP . . . . . . . . . . . . . . . . . . . . . . . . 55Touch tone dialing . . . . . . . . . . . . . . . 95Transferring PC address bookto directory . . . . . . . . . . . . . . . . 134Transmission Control Protocol. . . . . . 183Transmission powerreducing for the base station. . . . . . 69Transmission rate. . . . . . . . . . . . . . . 183Transport Layer Security . . . . . . . . . . 183Transport protocol. . . . . . . . . . . . . .  183TroubleshootingInternet connection . . . . . . . . . . . . 27UUDP . . . . . . . . . . . . . . . . . . . . . . . .  183Uniform Resource Identifier. . . . . . .  183Universal Resource Locator  . . . . . . .  183Unknown . . . . . . . . . . . . . . . . . . . . .  43Unknown caller. . . . . . . . . . . . . . . . .  43URI . . . . . . . . . . . . . . . . . . . . . . . . .  183URL  . . . . . . . . . . . . . . . . . . . . . . . .  183Use random ports . . . . . . . . . . . . . . 129User Datagram Protocol. . . . . . . . . .  183User ID . . . . . . . . . . . . . . . . . . . . . .  183User identification. . . . . . . . . . . . . .  184User name (VoIP-Account). . . . . . . .  110VvCard format. . . . . . . . . . . . . . . . . .  136vcf file  . . . . . . . . . . . . . . . . . . . . . .  134Version check, automatic. . . . . . . . .  138Voice over Internet Protocol. . . . .  9, 184Voice quality . . . . . . . . . . . . . . . . . .  115Voice quality and infrastructure . . . . 118VoIP . . . . . . . . . . . . . . . . . . . . . . . .  184accepting/rejecting call waiting  . . .  56activating/deactivating call waiting.  54activating/deactivating status message . . . . . . . . . . . . . . . . . 93advantages . . . . . . . . . . . . . . . . . . . 9assigning IP address . . . . . . . . . . . .  91call forwarding  . . . . . . . . . . . . . . .  53completing settings . . . . . . . . . . . . 26conference call  . . . . . . . . . . . . . . . 55configuring account. . . . . . . . . . .  107configuring account (first) . . . . . . .  24connection name. . . . . . . . . . . . .  108displaying called party's number. . .  44external consultation call . . . . . . . . 55loading provider data. . . .  23, 89, 109making call settings . . . . . . . . . . . .  53network services . . . . . . . . . . . . . .  53phone number  . . . . . . . . . . .  26, 108prerequisites . . . . . . . . . . . . . . . . . .  9settings (on handset) . . . . . . . . . . .  89starting connection wizard. . . .  21, 89status codes (table) . . . . . . . . . . .  145toggling  . . . . . . . . . . . . . . . . . . . .  55

Navigation menu