Gigaset Communications MD40 DECT module User Manual OEM Instructions

Gigaset Communications GmbH DECT module OEM Instructions

UserManual.wiki >

Gigaset Communications >

MD40 User Manual >

OEM Instructions HTML Version

1. Installation Guide
2. OEM Instructions

OEM Instructions

16.09.2011

Page 1 of 6

OEMinstructions



Themanufactureroftheendproductshallconsiderthefollowinghints:



1)Theendproduct(host)withthemodulebuiltinsidemustbemarkedasfollows:



ContainsTransmitterModuleFCCID:TVU‐MD40/IC:8023A‐MD40

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmful

interference,and(2)thisdevicemustacceptanyinterferencereceived,including

interferencethatmaycauseundesiredoperation.

ModuletransmetteurIDIC:8023A‐MD40.

Sonfonctionnementestsoumisauxdeuxconditionssuivantes:(1)cetappareilnedoitpas

causerd’interférencesnuisibleset(2)appareildoitacceptertouteinterferencerecue,y

comprislesinterferencesquipeuventpertuberlefontionnement.



2)Thefollowingregulatorystatementsshallbeprintedintheusermanualfortheend

product.



FCCInformation:

Changesormodificationstotheequipmentnotexpresslyapprovedbythepartyresponsible

forcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassBdigital

device,pursuanttoPart15oftheFCCRules.Operationissubjecttothefollowingtwo

conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)Thisdevicemust

acceptanyinterferencereceived,includinginterferencethatmaycauseundesired

operation.

Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceina

residentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful

interferencetoradiocommunications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.If

thisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcan

bedeterminedbyturningthesystemoffandon,theuserisencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

1.Reorientorrelocatethereceivingantenna.

2.Increasetheseparationbetweentheendproductandreceiver.

3.Connecttheendproductintoanoutletonacircuitdifferentfromthattowhichthe

receiverisconnected.

4.ConsultthedealeroranexperiencedradioTVtechnicianforhelp.



22.09.2011 Page 2 of 6



IndustryCanadaInformation:

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcause

interference,and(2)thisdevicemustacceptanyinterference,includinginterferencethat

maycauseundesiredoperationofthedevice.

NOTICE:TheIndustryCanadalabelidentifiescertifiedequipment.Thiscertificationmeans

thattheequipmentmeetscertaintelecommunicationsnetwork,protective,operationaland

safetyrequirementsasprescribedintheappropriateTerminal

EquipmentTechnicalRequirementsdocument(s).TheDepartmentdoesnotguaranteethe

equipmentwilloperatetotheuser’ssatisfaction.

Repairstocertifiedequipmentshouldbecoordinatedbyarepresentativedesignatedbythe

supplier.

Usersshouldensurefortheirownprotectionthattheelectricalgroundconnectionsofthe

powerutility,telephonelinesandinternalmetallicwaterpipesystem,ifpresent,are

connectedtogether.

Thisprecautionmaybeparticularlyimportantinruralareas.

NOTE:Usersshouldnotattempttomakesuchconnectionsthemselves,butshouldcontact

theappropriateelectricinspectionauthority,orelectrician,asappropriate.Thisproduct

meetstheapplicableIndustryCanadatechnicalspecifications.

ThisClassBdigitalapparatuscomplieswithCanadianICES‐003.

CetappareilnumériquedelaclasseBestconformeàlanormeNMB‐003duCanada.



3)GeneralInformation



AhostproductisrequiredtocomplywithallapplicableFCCequipmentauthorizations

regulations,requirementsandequipmentfunctionsnotassociatedwiththetransmitter

moduleportion.Forexample,compliancemustbedemonstratedtoregulationsforother

transmittercomponentswithinthehostproduct;torequirementsforunintentional

radiators(Part15B),suchasdigitaldevices,computerperipherals,radioreceivers,etc.;and

toadditionalauthorizationrequirementsforthenon‐transmitterfunctionsonthe

transmittermodule(i.e.,Verification,orDeclarationofConformity)(e.g.,BluetoothandWiFi

transmittermodulesmayalsocontaindigitallogicfunctions)asappropriate.



Toensurecompliancewithallnon‐transmitterfunctionsthehostmanufactureris

responsibleforensuringcompliancewiththemodule(s)installedandfullyoperational.For

example,ifahostwaspreviouslyauthorizedasanunintentionalradiatorunderthe

DeclarationofConformityprocedurewithoutatransmittercertifiedmoduleandamoduleis

added,thehostmanufacturerisresponsibleforensuringthatafterthemoduleisinstalled

andoperationalthehostcontinuestobecompliantwiththePart15Bunintentionalradiator

requirements.



22.09.2011 Page 3 of 6



Singleorlimited‐singlemodulesandtheRFfront‐endsectionofasplitorlimitedsplit‐

modulemustbeaseparatephysicalassemblythatcanbeinstalledinto(orattachedto)a

hostasaseparatesub‐assembly(daughter‐boardsub‐assembly).Themethodusedforinput

andoutputelectricalconnectionstothehostcanbesoldered,cabled,wired,oruseplug‐in

connectors.Amodulecannotbesolelytheimplementationofadesignspecification.Only

thecontrol‐elementsectionofasplit‐moduledevicemaycomprisesoftwarecertifiedas

companioncodetoaspecificRFfront‐end(section).

Ahostusingacomponentthathasbeenauthorizedasamodulemay,subjecttothe

requirementsdescribedbelowandtheconditionsofthegrant,(1)bemarketedandsold

withthemodulebuiltinsidethatdoesnothavetobeend‐useraccessible/replaceable,or(2)

bemarketedwiththemodulebeingend‐userplug‐and‐playreplaceable.



Theantenna(s)usedforthistransmittermustnotbecollocatedoroperatedinconjunction

withanyotherantennaortransmitterwithinahostdevice,exceptinaccordancewithFCC

multi‐transmitterproductprocedures.



TheGigasetMD40willbedeliveredwithdefaultsettingswhichfulfilltheregulatory

standards.Ifparametersarechanged,theconformitytotheregulatorystandardscouldnot

befulfilled.Thedistributorhastoprovetheconformitytotheregulatoryrequirementsagain



4)SafetyInstructions



Incustomerrelateddocumentsoftheendproductlikeinstructionmanuals,installation

guidesetc.appropriatesafetyinstructionshavetobeincluded.

Thesupplierofthecompletesystemisresponsibleforthesesafetyinstructions.



ThetransmittedRF‐signalismodulatedinatimemultiplexprocesswithaframelengthof

10ms(100Hz).Apossibledemodulationindeviceswithelectro‐acousticallytransducerscan

causeahummingnoise.



ThetransmittedRF‐signalcancausemalfunctionsinelectronicdeviceslocatedclosetothe

module.



ThespecificexternalpowersupplyfortheCordlessVoiceModuleSC14CVMDECThasto

fulfilltherequirementsaccordingtoclause2.5(Limitedpowersource)ofthisstandardEN

60950‐1:2006.



Interconnectioncircuitsshallbeselectedtoprovidecontinuedconformancetothe

requirementsofclause2.2forSELV(SafetyExtraLowVoltage)circuitsaccordingtoEN

60950‐1:2006aftermakingconnections.



22.09.2011 Page 4 of 6



Requirementsadditionaltothosespecifiedincommonsafetystandardsmaybenecessary

for:

‐Equipmentintendedforoperationinspecialenvironments(forexample,extremesof

temperature,excessivedust,moistureorvibration,flammablegasesandcorrosiveor

explosiveatmospheres).

‐Equipmentintendedtobeusedinvehicles,onboardshipsoraircraft,intropicalcountries

orataltitudesgreaterthan2000m.

‐Equipmentintendedforusewhereingressofwaterispossible.



Installationbyqualifiedpersonnelonly!



Theproductisacomponentintendedforinstallationanduseincompleteequipment.The

finalacceptanceofthecomponentisdependentuponitsinstallationanduseincomplete

equipment.



GigasetMD40containsaninternalfusewhichisimplementedasatrackonthePCB.

Thefuseistrippedatacurrentof3‐4A.Themodulehastobeexchangedifthefuseis

blown.



Medicalandelectronicdevicescanbeaffectedintheirfunction.

Considerthetechnicalconditionsofyoursurroundinge.g.medicalpractice.



TheGigasetMD40cancauseannoyingnoiseinhearingaids.



Pointyourcustomertothefactthatyoursystem/devicebehaveslikeacordlesstelephone.

Thisappliesespeciallyfortheindoorandoutdoorrange.

Alsoconsiderthattheradiolinkcanbeinterruptedbyexternalenvironmentalinfluences

(e.g.motorvehicleswhichaffecttheradiocoverageattherangelimit).



Withoutasufficientsupplyvoltage(e.g.anemptybattery)theequipmentcan’twork

correctly.



22.09.2011 Page 5 of 6



5)Installationguide



Themoduleshallbeoperatedonlywiththevoltagestatedinthespecification.



ThemodulecontainsaninternalfusewhichisimplementedasatrackonthePCB.

Thefuseistrippedatacurrentof3‐4A.Themodulehastobeexchangedifthefuseis

blown.



TheMD40isintendedtobefixedatthehostboardwithtwoM2.5screwsondistancebolts.

Thetwodistanceboltsmusthavealengthof6.2mm(+‐0.2mm)andadiameterof

4mm(+‐0.5mm).



ThemoduleissuppliedwithtwoDECT‐antennasprings.

Theinternalantennasareinstalledbypluggingtheantennaspringsintotheantennaports.

Itisrecommendedtoprotecttheantennasagainstmechanicalshocksorvibrationinthe

hostdeviceinwhichtheengineisinstalled.



ThemoduleisconformwiththeFCCandIndustryCanadaregulationswiththeprovided

internalantennas(C39363‐A290‐B35/JohannVitzGmbH&Co.KG)only.

Ifotherantennasareusedintheendproduct,anewassessmentofconformitywiththe

regulatorystandardsismandatory.



22.09.2011 Page 6 of 6



Foroptimumperformance,anantennagenerallyneedstobesurroundedbyan

unobstructedspaceafewwavelengthsinsize.

Anydielectricorconductingmaterialintheimmediatevicinityofanantennaaffectsthe

radiationpatternandperformanceoftheantenna.Hence,whenevermechanicaldesign

allows,asmuchspaceaspossiblemustbeleftcleararoundtheantennaspring(min.40mm).

ThisensuresthattheimpactofsurroundingPCBsorotherconductingparts(cablesetc.)on

theantenna’sperformancecanbekeptatanacceptablelevel.

If,formechanicalreasons,thereisonlylimitedroomaroundtheengine’santennasprings,

theeffectofthisontheantenna’sperformanceandFCC/IndustryCanadatypeapprovals

needstobetakenintoaccount,togetherwiththeresultingreductioninachievablerange.

ForthepurposesofESDprotection,internalantennasmusthaveanairgapofatleast10

mmfromanypossiblepositionoftheESDtestfingerortestprobe,toavoidanairdischarge.



Ifexternalantennasareused,thegroundshieldofthecoaxialcableisconnectedtothe

groundofthehostinterface.Therequirementsofthesafetystandardshavetobe

considered.



Airdischargeontotheexternalantennaortheantennaconnectorsmaycausetemporary

lossofsynchronizationbetweenthefixedpartandtheportablepart.InV.24replacement

modethisresultsinaninterruptionoftheconnectionforseveralseconds.InGAP‐PPmode

theconnectionwillbereleased.

Toavoidtheseeffects,careshouldbetakenindesigningthehousingandthearrangement

oftheexternalantennas.Thecoaxialcableshieldingmustbepreventedfromconductionthe

dischargecurrentawayovertheDECTEnginee.g.byadirectgroundconnectiontoametal

housingontheantennaconnector.Ifaplastichousingisused,allmetallicsurfacesmustbe

coveredbyplasticmaterial.Metallicsurfacesshouldhaveanairgapofatleast10mmfrom

anypossiblepositionoftheESDtestfingerortestprobe,toavoidanairdischarge.



Gigaset Communications MD40 DECT module User Manual OEM Instructions

Gigaset Communications GmbH DECT module OEM Instructions

Contents

OEM Instructions

Navigation menu

Namespaces

Views

Navigation