Gold Light Toys Factory JG2017B24GT Drone Mach 5inch Racer 2pk With Obstacle Course User Manual 2017 06 07 DroneMach5inRacer2pk Simple IM

Download:
Mirror Download [FCC.gov]
Document ID	3577078
Application ID	k9alAMDB6k9x+oyiONc7hA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.19kB (427352 bits)
Date Submitted	2017-09-25 00:00:00
Date Available	2017-09-25 00:00:00
Creation Date	2017-06-27 09:30:07
Producing Software	Adobe PDF library 15.00
Document Lastmod	2017-06-27 09:30:07
Document Title	2017-06-07_DroneMach5inRacer2pk_Simple_IM
Document Creator	Adobe Illustrator CC 2017 (Macintosh)

2 PACK DRONES & FLAG DRONE RACER SET
12+
Getting to Know Your Drone
PLEASE READ ALL WARNINGS AND
INSTRUCTIONS PRIOR TO USE. KEEP THIS
DOCUMENT AS IT CONTAINS IMPORTANT
INFORMATION ABOUT YOUR DRONE.
1. PREPARE FOR FLIGHT
• Drone must be charged before each use
(Cable included)
• Indicator light will turn off once fully charged
• Install batteries in remote
2. PAIR YOUR DRONE
Before each flight pair the remote with the
drone:
1. Turn your drone on and place on a flat, level
surface
2. Turn on the remote on and move the left
joystick up, then down
3. The beep will indicate successful pairing
4. Repeat steps 1 and 2 if necessary
4. REMOTE CONTROL OVERVIEW
Practice flying your drone below 10 feet and at
low speeds until comfortable with all controls
to avoid unnecessary damage or injury
• Left joystick: left/right controls spin and
Up/Down controls elevation
• Right joystick: controls flight direction
• Direction Trim: use to eliminate drift
To cut power to drone, move left joystick to
down position
3. DIRECTIONAL LIGHTS
• White lights indicate the front of the drone
• Red lights indicate the back of the drone
• Not applicable in auto-orientation mode
QUESTIONS OR CONCERNS?
PLEASE GIVE US A CALL ... WE’RE HERE TO HELP
CUSTOMER SERVICE
ADULT ASSEMBLY, CHARGING, AND
BATTERY INSTALLATION IS REQUIRED.
ADULT SUPERVISION IS REQUIRED.
WARNING:
CHOKING HAZARD -
(800) 374-2744
Small Parts.
Not for Children under 3 years.
Before calling please locate the 10-digit
code printed on the back of your remote
©2017 MerchSource, LLC. All rights reserved.
Distributed by MerchSource, LLC, Irvine, CA 92618.
For technical support, please visit www.merchsource.com or call
1-800-374-2744.
The artwork and design of this manual are protected by US copyright law
and may not be reproduced, distributed, displayed, published or used for
any purpose without prior written permission. It is not permitted to alter,
remove or reproduce any trademarks or copyright notice from this
manual.
Printed in China.
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT
INFORMATION FOR FUTURE REFERENCE.
Due to continuous product improvements, the picture on the manual may
differ slightly from the actual product.
PATENT PENDING
2 PACK DRONES & FLAG DRONE RACER SET
INTRODUCTION
Congratulations on your purchase of the
Rechargeable 2.4 GHz 2 Pack Drones &
Flag Drone Racer Set. Get ready to soar
to new heights. Master the art of drone
flying with remote control
maneuverability. These lightweight
drones will provide hours of fun.
SPECIFICATIONS
Drone Battery: 350 mAh Li-po
Remote Controller Battery: 6 x 1.5V “AA”
Charging Time: 100 minutes
Maximum Recommended Altitude: 150 ft.
TABLE OF CONTENTS
General Warnings
Contents, Remote Battery Installation, Battery Warnings
Charging LiPo Battery and Replacing Propellers
Remote Overview
Operating Drone
Auto Orientation and Tips
Obstacle Course Setup
Printed in China.
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
2 PACK DRONES & FLAG DRONE RACER SET
READ ALL WARNINGS AND PRECAUTIONS BEFORE USE
SAFETY WARNINGS
• Not recommended for children under 12 years of age. As with all electrical products, precautions should be
observed during handling and use to reduce the risk of electrical shock.
• Adult supervision is required at all times
• Drive drone only on smooth flat surfaces
• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected
crashes.
• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of
others.
• The drone shall never be modified or used for anything except its intended purpose.
• Before each use, an adult should review the product and battery to determine that no damage or hazards exist
• DO NOT TOUCH SPINNING PROPELLERS
• Do not allow anything to intentionally make contact in any way with spinning propellers
o Prevent contact with spinning blades by turning off remote prior to handling drone
• Use caution and pay attention to your surroundings while operating drone
• Do not fly drone into animals, people, or inanimate objects
• Keep drone away from power lines, buildings, trees, public areas, and any other potentially hazardous areas.
• Do not operate in rain, heavy wind, and or any type of severe weather
• Do not land drone on wet surfaces
• Never touch or allow others to touch drone while it is flying
• Always turn drone off when it is not in use
• Always fly drone in large open areas
• The drone will lose controlling capabilities if fly distance is more than maximum recommended altitude of 100 ft.
Keep below 100 ft. to avoid potential crashing risk.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
Fly-aways are the responsibility of the individual
pilot and will not be replaced by the manufacturer.
Drone is powered by a rechargeable 3.7V 350mAh Li-Po battery (included). Transmitter
requires 6 “AA” batteries (not included). Colors and styles may vary. *This drone weighs
0.192 lbs (87g). As of December 21, 2015, the Federal Aviation Administration (FAA) only
requires registration on unmanned aircrafts weighing more than 0.55 lbs. Visit
www.faa.gov/uas/registration/ for more information. Although the FAA does not require this
drone to be registered, ongoing compliance with federal, state, and local laws is an owner’s
sole responsibility. Always fly safely and respect the privacy of others.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Printed in China.
TROUBLESHOOTING:
When remote switch is turned on, the remote light does not
illuminate:
1) Check that batteries in the remote are installed correctly OR
2) Replace with new batteries
When the remote is switched on, the remote LED is flashing and
remote is beeping:
1) Remote batteries are low; replace them with new batteries
Drone and remote properly pair, but the drone will not lift-off:
1) Drone Li-Po needs charging. Use charging cable to connect the
drone to power source.
After trimming the drone, the drone flight is very unstable and
cannot fly properly:
1) One or more blades are most likely damaged;
2) Turn off the drone and remote.
3) Replace with the proper number replacement blade and try
flying again.
After impact, the drone is unstable:
1) Put the left remote control lever to the left bottom and put the
right remote control lever to the right bottom at the same time
which connected to the drone (diagram to right).
2) If the above does not resolve the issue, reboot the drone and
controller and pair again.
Remote Controller and Drone can not be paired:
1) Check Point: Remote Controller must be closed to Drone, not
exceed 4 meters.
Note: If there are 2 sets of Drones within 4 meters for Pairing, you
must pair one successfully before pairing the second set.
2 PACK DRONES & FLAG DRONE RACER SET
CONTENTS
REMOTE BATTERY INFORMATION
1. Slide open the remote’s battery compartment.
2. Install 6 “AA” batteries as shown in the
diagram above.
3. Replace and close battery compartment.
Mach Drone x2
AUTO
ORIENTATION
60
100
LAND
LITHIUM-POLYMER BATTERY WARNING
ON
SPRINT
TRIM
DIRECTION
TRIM
OFF
Drone Controller x2
Racing
Flag
Start/
Finish Line
There is a risk of fire and personal injury if Li-Po
battery is punctured, damaged or misused.
• Never expose battery to extreme temperatures
or moisture.
• Do not subject battery to strong impacts
• Always keep battery away from flammable
materials.
• Only use manufacturer specified batter(ies),
charger(s), and/or adapters, if applicable.
• Battery is not serviceable.
• Let battery cool to room temperature before
charging.
• While charging, never leave battery unattended.
• Recycle or dispose of battery according to federal,
state and local laws.
KEEP THIS INSTRUCTION MANUAL FOR REFERENCE
Charge Cable x2
Printed in China.
Replacement
Propellors
BATTERY WARNING - ALKALINE (AA)
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Insert batteries using the correct polarity. Do not short-circuit the supply terminal.
• Only use manufacturer specified batter(ies), charger(s), and/or adapters, if
applicable, specified by the manufacturer.
• Always use, replace, and recharge (if applicable) batteries under adult supervision.
2 PACK DRONES & FLAG DRONE RACER SET
CHARGING BATTERY
Note: The Battery Charger will light up when it is
charging the battery and turn off when the
battery is fully charged. Charge time is
approximately 100 minutes.
1. Turn off the drone before charging.
2. Connect the Battery Charger Cable to the
port found on the rear of the drone
3. Connect USB connector to the power source.
Connect the Charge
Cable to the Drone
Insert the
Charge Cable
into a power
source
Replacing Propellers
1. Follow diagram.
2. Remove screw from top of Propeller.
3. Remove broken Propeller and replace with
new Propeller.
4. Make sure you installed the correct blade.
Each blade has a number written on it. Match
the blades with the corresponding number on
the drone
5. Insert screw into top of Propeller
NOTE: Blade 1 turns counter clockwise and
Blade 2 turns clockwise
Printed in China.
2 PACK DRONES & FLAG DRONE RACER SET
REMOTE OVERVIEW
Forward/ Backwards
Adjustment: Slide up to
adjust forward and slide
down to adjust backwards
Power indicator
light
Multi Directional
Joystick
Auto orientation
AUTO
ORIENTATION
Throttle Joystick:
Increases or decreases
drone elevation
left/right controls spin
Side to Side Adjustment:
Slide left to adjust to the
left and slide right to
adjust to the right
60
100
ON
AUTO
TAKEOFF
AUTO
LAND
DIRECTION
TRIM
OFF
Auto takeoff
Auto land
Speed control
ON/OFF
Remote switch
Printed in China.
2 PACK DRONES & FLAG DRONE RACER SET
OPERATING DRONE
Step 1 – Pre-Flight Checklist
• Read all warnings and instructions
• Install remote batteries, page 2 .
• Charge batteries, page 3.
• Make sure that drone and remote are powered
off.
Step 2 – Choosing a location
• Drone is designed to be flown/driven indoors
and outdoors
• Always make sure you have enough space to
fly drone
• Always follow warnings, page 1.
Step 3 – Starting Drone
1. Making sure your remote is off, slide drone
switch to ON. Drone lights will begin to flicker
2. Choose a flat even surface and follow the
diagram
3. Turn remote on. Bring the Throttle all the way
up then bring it all the way down. Remote will
beep and drone lights will flicker rapidly then
turn on permanently once paired.
4. Drone is ready for flight.
FE
10
0F
EET
10
FE
FEE
ET
Fig. 1
Printed in China.
Step 5 – Drone Begins to Drift
Follow this step if your drone begins to drift
while take off or during flight
• Drone drifts backwards: Slide the
Forward/Backwards Adjustment up
• Drone drifts forwards: Slide th
Forward/Backwards Adjustment down
• Drone drifts left: Slide the Side to Side
Adjustment to the right.
• Drone drifts right: Slide the Side to Side
Adjustment to the left.
• Drone spins clockwise (viewing drone from
top): Slide the Spin Adjustment to the left
• Drone spins counter-clockwise (viewing drone
from top): Slide the Spin Adjustment to the
right.
Always turn off remote prior to retrieving or
picking up drone. This will help you avoid
accidently activating propellers.
5 FEET
10
Step 4 – Lift Off
1. Slowly and carefully bring the throttle up.
Propellers will begin to spin and drone will
begin to elevate. You can compensate for
some of the drones drifting by using the Multi
Directional Button or by following step 5. You
may need to practice this step several times
before successfully getting drone into the air.
Step 6 – Operating Drone in Flight
The drones range is approximately 150 feet
• Read and be aware of all warnings found on
page 1.
• Maintain your desired elevation by using the
Throttle
• Use the Throttle joystick in a circle motion to
spin the drone
• Use the Multi Directional Joystick to move
forwards, backwards, and side to side
• Review step 5 if your drone begins to drift
2 PACK DRONES & FLAG DRONE RACER SET
OPERATING DRONE (Cont.)
Step 7 – Landing Drone
• Make sure you have achieved level, balanced flight, where the drone is neither climbing nor
descending. This mode allows you to safely and slowly land your drone without having to control
the speed.
• The ideal auto landing height is 25-30ft.
• Press the land button to trigger auto land. Remote will beep continuously until you exit the auto
land mode.
• To steer the drone during landing, use the right control until drone has reached the ground.
• Press the land button again to exit auto landing mode.
NOTE: Please make sure the throttle joystick is on down position before exit auto landing
mode.
Step 8 – Retrieving Drone
1. Turn off your remote by pressing the Power Button. This will stop you from accidentally turning
the propellers on.
2. Make sure the propellers have stopped spinning then pick up your drone.
Note: You will need to pair your drone again before your next flight.
Auto Orientation Button
• Auto Orientation default setting is off. To enter this mode press Auto Orientation button. Remote
will beep twice.
• After drone success paired, the 2 white LED lights toward orientation will be the original forward
orientation, when drone is in auto orientation mode, whatever the drone spin, the forwar
dorientation will be previous original forward orientation.
• Remote will beep every 6s to indicate the drone is in Auto Orientation mode.
• To exit mode, press the button. Remote will sound 1 long beep indicating that it has exited Auto
Orientation mode.
Tips
• Do not crash drone into sand or dirt. Drone gears may become clogged
• When first learning to fly, practice lifting off and hovering
• Stay several feet from walls and buildings.
Printed in China.
2 PACK DRONES & FLAG DRONE RACER SET
OBSTACLE COURSE SETUP
Printed in China.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42
Format                          : application/pdf
Title                           : 2017-06-07_DroneMach5inRacer2pk_Simple_IM
Metadata Date                   : 2017:06:27 09:30:07-07:00
Modify Date                     : 2017:06:27 09:30:07-07:00
Create Date                     : 2017:06:27 09:30:07-07:00
Creator Tool                    : Adobe Illustrator CC 2017 (Macintosh)
Thumbnail Width                 : 200
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 23595 bytes, use -b option to extract)
Instance ID                     : uuid:23b8e184-ec88-fb4a-994a-1052406252c1
Document ID                     : xmp.did:2ed5154e-be24-4371-ae83-d89776316f44
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:0230feaa-9559-2d49-9c82-96305de3f29f
Derived From Document ID        : xmp.did:24b096ae-f610-4e03-befb-7177bc57a892
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : default
History Action                  : saved, saved
History Instance ID             : xmp.iid:47ded613-3c0a-4b82-a0a0-ad998d53f648, xmp.iid:2ed5154e-be24-4371-ae83-d89776316f44
History When                    : 2017:04:18 15:18:19-07:00, 2017:06:27 09:30:04-07:00
History Software Agent          : Adobe Illustrator CC 2017 (Macintosh), Adobe Illustrator CC 2017 (Macintosh)
History Changed                 : /, /
Manifest Link Form              : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference
Manifest Reference File Path    : /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/Racing-Drone-White_BW.psd, /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/Racing-Drone-Angle3-002_BW.tif, /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/MACHDRONE5IN_Remote_White_BW.psd, /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/MACHDRONE5IN_Remote_Red_BW.psd, /private/var/folders/8l/bmkkpknj1g38v4jdbhxwbd_d2dfk__/T/TemporaryItems/(A Document Being Saved By Illustrator CC)/Zp4BE0.tif
Manifest Reference Document ID  : adobe:docid:photoshop:2c713e9a-e37c-1179-a497-9e36b0925ce7, xmp.did:1dfd79a8-35ef-4a23-af68-ff95551e02ed, adobe:docid:photoshop:13c2a21b-7e53-117a-9247-e2fb5aee727b, adobe:docid:photoshop:02825457-7e53-117a-9247-e2fb5aee727b
Manifest Reference Instance ID  : xmp.iid:a04ce74c-0da3-4e77-bf86-d0b2c46490e3, xmp.iid:477a8d81-cf28-4696-aef8-218447864706, xmp.iid:7cb064a8-3397-4370-b72a-d90c8079dc69, xmp.iid:17f0f3d9-739d-4c96-8d68-72486d88f588
Ingredients File Path           : /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/Racing-Drone-White_BW.psd, /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/Racing-Drone-Angle3-002_BW.tif, /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/MACHDRONE5IN_Remote_White_BW.psd, /Users/dinhtran/Desktop/2017-06-07_DroneMach5inRacer2pk_Simple_IM/Links/MACHDRONE5IN_Remote_Red_BW.psd, /private/var/folders/8l/bmkkpknj1g38v4jdbhxwbd_d2dfk__/T/TemporaryItems/(A Document Being Saved By Illustrator CC)/Zp4BE0.tif
Ingredients Document ID         : adobe:docid:photoshop:2c713e9a-e37c-1179-a497-9e36b0925ce7, xmp.did:1dfd79a8-35ef-4a23-af68-ff95551e02ed, adobe:docid:photoshop:13c2a21b-7e53-117a-9247-e2fb5aee727b, adobe:docid:photoshop:02825457-7e53-117a-9247-e2fb5aee727b
Ingredients Instance ID         : xmp.iid:a04ce74c-0da3-4e77-bf86-d0b2c46490e3, xmp.iid:477a8d81-cf28-4696-aef8-218447864706, xmp.iid:7cb064a8-3397-4370-b72a-d90c8079dc69, xmp.iid:17f0f3d9-739d-4c96-8d68-72486d88f588
Startup Profile                 : Print
Has Visible Overprint           : True
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 8.500000
Max Page Size H                 : 11.000000
Max Page Size Unit              : Inches
Font Name                       : DINNextLTPro-Bold, Helvetica, Helvetica-Bold, HelveticaNeue, HelveticaNeue-Bold, Univers-Condensed, HelveticaNeue-MediumCond, HelveticaNeue-BoldCond
Font Family                     : DIN Next LT Pro, Helvetica, Helvetica, Helvetica Neue, Helvetica Neue, Univers, Helvetica Neue, Helvetica Neue
Font Face                       : Bold, Regular, Bold, Regular, Bold, 57 Condensed, 67 Medium Condensed, 77 Bold Condensed
Font Type                       : Open Type, TrueType, TrueType, TrueType, TrueType, Type 1, Type 1, Type 1
Font Version                    : Version 1.200;PS 001.002;hotconv 1.0.38, 12.0d1e3, 12.0d1e3, 12.0d0e2, 12.0d0e2, 001.002, 001.000, 001.000
Font Composite                  : False, False, False, False, False, False, False, False
Font File Name                  : DINNextLTPro-Bold.otf, Helvetica.dfont, Helvetica.dfont, HelveticaNeue.dfont, HelveticaNeue.dfont, UniveCon; Univers-Condensed, HelveNeuMedCon; HelveticaNeue-MediumCond, HelveNeuBolCon; HelveticaNeue-BoldCond
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE Red 032 C
Swatch Groups Colorants L       : 55.294117
Swatch Groups Colorants A       : 72
Swatch Groups Colorants B       : 43
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Group Name        : Brights
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000000
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003100
Swatch Groups Colorants Black   : 0.003100
Producer                        : Adobe PDF library 15.00
Creator Version                 : 21.0.2
Page Count                      : 9
Creator                         : Adobe Illustrator CC 2017 (Macintosh)

EXIF Metadata provided by EXIF.tools