Golds Gym Ggsy2921 0 Users Manual GGSY29210 180550
Golds-Gym-Ggsy2921-0-Users-Manual-468564 golds-gym-ggsy2921-0-users-manual-468564
Golds-Gym-Ggsy29210-Owners-Manual golds-gym-ggsy29210-owners-manual
GGSY2921.0 to the manual e01931dc-76a9-41bd-a257-5fb4e0fb3961
2015-02-02
: Golds-Gym Golds-Gym-Ggsy2921-0-Users-Manual-429502 golds-gym-ggsy2921-0-users-manual-429502 golds-gym pdf
Open the PDF directly: View PDF 
.
Page Count: 17
| Download | |
| Open PDF In Browser | View PDF |
Æ ® Model No. GGSY2921.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if a part is damaged or missing, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT DIRECTLY. CALL TOLL-FREE: 1-877-776-4777 Mon.–Fri., 6 a.m.–6 p.m. MST ON THE WEB: www.goldsgympowerflex.com CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover Note: a PART LIST/EXPLODED DRAWING is attached in the center of this manual. Remove the PART LIST/EXPLODED DRAWING before beginning assembly. GOLD'S GYM is a registered trademark of Gold's Gym International, Inc. This product is manufactured and distributed under license from Gold's Gym International, Inc. 2 IMPORTANT PRECAUTIONS WARNING : To reduce the risk of serious injury, read the following important precautions before using the resistance system. 1. Read all instructions in this manual and in the accompanying literature, and all warnings on the resistance system before using the resistance system. Use the resistance system only as described in this manual. 11. Use the resistance system only with the included resistance bands, or those included with an optional GOLD’S GYM MAX PACK. Do not use other types of weight or resistance. 2. It is the responsibility of the owner to ensure that all users of the resistance system are adequately informed of all precautions. 12. Pull on the long nylon rope only while sitting on the bench or standing on the base cover. Pull on the medium nylon ropes only while sitting on the bench, with the seat in one of the three positions closest to the upright base, or while standing on the base cover. 3. The resistance system is intended for home use only. Do not use the resistance system in any commercial, rental, or institutional setting. 13. If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down. 4. Keep the resistance system indoors, away from moisture and dust. Place the resistance system on a level surface, with a mat beneath it to protect the floor or carpet. Make sure that there is enough clearance around the resistance system to mount, dismount, and use the resistance system. 14. The decals shown below have been placed on the resistance system in the locations shown on page 4. If a decal is missing or illegible, call the toll-free telephone number on the front cover of this manual and order a free replacement decal. Apply the replacement decal in the location shown. 5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately. 6. Keep children under 12 and pets away from the resistance system at all times. 7. Always wear athletic shoes for foot protection. 8. Keep hands and feet away from moving parts. 9. Make sure that the nylon ropes remain on the pulleys at all times. If the nylon ropes bind while you are exercising, stop immediately and make sure that the nylon ropes are on all of the pulleys. Decal 1 Decal 2 10. The resistance system is designed to support a maximum user weight of 250 pounds. WARNING: Keep hands and fingers clear of this area. Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 3 BEFORE YOU BEGIN Thank you for selecting the versatile GOLD’S GYM® POWER FLEX resistance system. The resistance system offers a selection of weight stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the resistance system will help you to achieve the specific results you want. and serial number before calling. The model number is GGSY2921.0. The serial number can be found on a decal attached to the resistance system (see the front cover of this manual). To avoid a registration fee for any service needed under warranty, you must register the resistance system at www.goldsgympowerflex.com/registration. For your benefit, read this manual carefully before using the resistance system. If you have additional questions, see the front cover of this manual. To help us assist you, please note the product model number Before reading further, please familiarize yourself with the parts that are labeled in the drawing below. ASSEMBLED DIMENSIONS: Height: 77 in. / 196 cm Width: 34 in. / 86 cm Depth: 83 in. / 211 cm High Pulley Station *Exterior bands are an optional accessory available with a GOLD’S GYM MAX PACK. To purchase a MAX PACK, call our Customer Service Department at the number on the front cover of this manual. Left Side Resistance Handle Right Side Cover Clip Backrest Exterior Bands* Low Pulley Station Seat Wheel Decal 1 Leg Developer Leg Lever Bench Frame Decal 2 Folding Bracket Note: The terms “right side” and “left side” are determined relative to a person sitting on the seat; they do not correspond to right and left on the drawings in this manual. 4 PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. M8 Split Washer (104) M10 Split Washer (70) M10 x 25mm Button Screw (83) M6 x 38mm Screw (90) M6 Washer (69) M8 x 38mm Carriage Bolt (75) M8 Nylon Locknut (71, 105) M10 x 60mm Button Bolt (89) M8 x 25mm Button Screw (74) M8 x 64mm Bolt (101) M8 x 25mm Patch Screw (25) M10 x 69mm Bolt (91) M4 x 25mm Screw (85) M6 x 16mm Screw (67) M8 x 70mm Carriage Bolt (76) M4 x 16mm Screw (86) M10 x 83mm Bolt (92) M4 x 12mm Screw (102) M10 x 107mm Bolt (88) 5 M10 x 215mm Bolt (81) M10 Nylon Locknut (72) ASSEMBLY • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Make Things Easier for Yourself This manual is designed to ensure that the resistance system can be assembled successfully by anyone. Most people find that by setting aside plenty of time, assembly will go smoothly. The following tools (not included) are required for assembly: • Two adjustable wrenches Before beginning assembly, carefully read the following information and instructions: • One rubber mallet • One standard screwdriver • Assembly requires two people. • One Phillips screwdriver • For help identifying small parts, use the PART IDENTIFICATION CHART on page 5. • One Allen wrench (included) • Tighten all parts as you assemble them, unless instructed to do otherwise. • Lubricant, such as grease or petroleum jelly. Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. • As you assemble the system, make sure all parts are oriented as shown in the drawings. 1. 1 Before beginning assembly, be sure that you have read and understand the information in the box above. 71 71 Attach two Plastic Feet (46) to the Base Stabilizer (3) with two M4 x 16mm Screws (86). 71 46 86 Attach the Base Stabilizer (3) to the Base (4) with two M8 x 38mm Carriage Bolts (75), two M8 x 64mm Bolts (101), and four M8 Black Nylon Locknuts (71). 3 101 2. Attach two Plastic Feet (46) to the Base Cover (5) with two M4 x 16mm Screws (86). 2 Attach the Base Cover (5) to the Base Stabilizer (3) and Base (4) with three M4 x 25mm Screws (85). 4 75 46 86 46 86 85 5 85 46 86 3 6 4 3. Attach the Left Arm (12) to the Upright Base (6) with two M10 x 25mm Button Screws (83) and two M10 Split Washers (70). Note: Make sure that the grip tape is on top. 3 Attach the Right Arm (not shown) in the same manner. 12 70 6 4. Orient the Upright Stabilizer (7) as shown. Attach the Upright Stabilizer to the Upright Base (6) with two M8 x 70mm Carriage Bolts (76) and two M8 Black Nylon Locknuts (71). 70 Grip Tape 83 83 4 7 76 71 5. Slide the Base (4) into the Upright Base (6). Tip the Upright Base onto its back. Attach the Base to the Upright Base with the four M8 x 25mm Patch Screws (25). 5 71 6 Tip 4 7 6 25 25 6. Press two 57.1mm Round Outer Caps (59) onto the ends of the Front Leg (1). 6 36 Pull the Seat Knob (36) out as far as it will go and remove the Seat Frame (19) from the Bench Frame (2) and set it aside. 2 39 Orient the Bench Frame (2) as shown. Slide the Front Bench Frame Plate (39) into the indicated end of the Bench Frame, and align the holes in the Plate with the holes in the Bench Frame. 59 Orient the Front Leg (1) as shown. Attach the Front Leg to the Bench Frame (2) with the Front Bench Frame Plate (39), four M8 x 25mm Button Screws (74) and four M8 Split Washers (104). Holes 104 104 74 74 7. Orient the Seat (20) and Seat Backing (115) as shown. Attach the Seat and Seat Backing to the Seat Frame (19) with four M6 x 16mm Screws (67). 19 59 1 7 20 Round End 115 19 8. Pull the Seat Knob (36, not shown) out as far as it will go, and slide the Seat Frame (19) onto the Bench Frame (2). Engage the Seat Knob into the third hole from the end of the Bench Frame. 8 Third Hole 36 Press the two Frame Inner Caps (58), with the wide ends oriented as shown, into the ends of the Bench Frame (2). Attach the Caps with four M4 x 16mm Screws (86). Locate the Short Nylon Rope (54), which has three ends connected in the middle with a bracket. Note that two ends of the Rope go out of one side of the bracket, and the third (single) end goes out the other side of the bracket. Route the single end of the Short Nylon Rope under a “V”-Pulley (49). Attach the Pulley to the Front Leg (1) with an M10 x 107mm Bolt (88) and an M10 Nylon Locknut (72). 67 58 2 86 Wide End 72 8 1 54 86 19 49 88 86 Wide End 2 86 58 9. Lubricate an M10 x 83mm Bolt (92). Attach the Pivot Bracket (23) to the Base (4) with the Bolt, an M10 Nylon Locknut (72), and a Bench Knob (41). 9 41 23 72 92 4 10. Press two 2” Round Inner Caps (56) into the top and bottom of the Leg Developer (21). Press two 46mm Round Inner Caps (55) into the top and bottom of the Leg Lever (22). 10 Attach the Eyebolt (63) to the indicated side of the Leg Lever (22) with an M8 Zinc Nylon Locknut (105). Lubricate an M10 x 69mm Bolt (91). Attach the Leg Lever (22) to the Leg Developer (21) with the Bolt and an M10 Nylon Locknut (72). 38 Press four 19mm Round Inner Caps (60) into the tubes on the Leg Developer (21) and the Leg Lever (22). Slide four Foam Pads (38) onto the tubes. Slide the Leg Developer (21) into the Bench Frame (2). Align the hole in the Leg Developer with a hole in the Front Leg (1). Tighten a Bench Knob (41) into the hole in the Leg Developer. 38 60 55 60 Tube 21 22 Hole 55 63 11 38 38 91 2 Round End 116 57 69 17 57 9 60 56 41 18 Orient the Backrest (18) and Backrest Backing (116) as shown. Attach the Backrest and Backrest Backing to the Backrest Frame (17) with four M6 Washers (69) and four M6 x 38mm Screws (90). Lubricate 60 1 11. Press four 1” Square Inner Caps (57) into the ends of the Backrest Frame (17). Attach a Plastic Foot (46) to the Backrest Frame with an M4 x 12mm Screw (102). 56 72 Tube 105 Lubricate 69 69 90 46 102 69 90 12. Slide the Backrest Frame (17) into the slot in the Seat Frame (19). Rest the Backrest Frame against the Upright Base (6). 12 6 19 Slot 13 Wrap a Medium Nylon Rope (52) around a “V”Pulley (49) with the ball on the side shown. Note: Be sure the ball is on the correct end of the Rope; it should slide over the bracket holding the loop. Attach the Pulley to the Pulley Arm (14) on the Right Upright (9) with an M10 x 60mm Button Bolt (89), two Pulley Bushings (48), and an M10 Nylon Locknut (72). 13 89 Loop Repeat this step with the Left Upright (not shown). 48 52 Ball 14. Slide the Upright Cover (34) onto the Upright Base (6). Tip the Upright Cover forward and press down so that the front tabs engage the Left and Right Covers (10, 11). Press the back of the Upright Cover so that the rear tabs engage the Left and Right Covers. 49 72 14 9 48 14 72 Orient the Left and Right Uprights (8, 9) as shown. Slide the Uprights onto the Upright Base (6). Attach the Left Upright to the Right Upright with an M10 x 215mm Bolt (81), the Upright Spacer (65), and an M10 Nylon Locknut (72). Do not tighten the Nylon Locknut yet. 9 Attach the Left and Right Uprights (8, 9) to the Upright Base (6) with four M8 x 25mm Button Screws (74) and four M8 Split Washers (104). Tighten the M10 Nylon Locknut (72). 15. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page. 17 Front Tabs 6 11 10 65 104 74 34 81 8 74 104 10 ADJUSTMENTS The instructions below describe how each part of the resistance system can be adjusted. Refer to the exercise guide accompanying this manual to see how the resistance system should be set up for each exercise. IMPORTANT: When attaching the leg press strap, ankle strap, or handles, make sure that the accessories are in the correct starting position for the exercise to be performed. If there is any slack in the nylon ropes as an exercise is performed, the effectiveness of the exercise will be reduced. ATTACHING THE SHORT NYLON ROPE 22 The Short Nylon Rope (54) has three ends connected in the middle with a bracket. Note that two ends of the Rope go out of one side of the bracket, and the third (single) end goes out the other side of the bracket. 63 31 To use the Leg Lever (22), attach the single end of the Short Nylon Rope (54) to the Eyebolt (63) on the Leg Lever with a Cable Clip (31), as shown in the inset drawing. 49 54 Attach the shorter of the other two ends of the Short Nylon Rope (54) to the left end of the Long Nylon Rope (53) with a Cable Clip (31). Attach the final end of the Short Nylon Rope to the right end of the Long Nylon Rope in the same manner. Note: Only the left end of the Long Nylon Rope is shown. 31 53 54 ATTACHING THE MEDIUM NYLON ROPE To use the high pulley stations, attach each Medium Nylon Rope (52) to an end of the Long Nylon Rope (53) with a Cable Clip (31). 10 When the Medium Nylon Ropes (52) are not connected to the Long Nylon Rope (53), snap the Medium Nylon Ropes into the cover clips on the Left and Right Covers (10, 11) to hold them out of the way. Cover Clip 11 52 31 53 11 Cover Clip ADJUSTING THE LEG DEVELOPER To adjust the height of the Leg Developer (21), unscrew the Bench Knob (41) from the Front Leg (1). Align the hole in the Leg Developer with one of the three holes in the Front Leg. Retighten the Knob into the Front Leg and Leg Developer. 21 To remove the Leg Developer (21), make sure the short nylon rope is not attached to the eyebolt in the leg lever (see ATTACHING THE SHORT NYLON ROPE on page 11). Unscrew the Bench Knob (41) from the Front Leg (1) and lift the Leg Developer out of the Bench Frame (2). 41 2 1 ADJUSTING THE BACKREST 9 The Backrest (18) can be used in any of five positions: two level positions or three inclined positions. To use the Backrest in a level position, pull the Seat Knob (36) out as far as it will go. Move the Seat (20) and engage the Knob into one of the two adjustment holes in the Bench Frame (2) that are closest to the Leg Developer (21). Rest the Backrest on the Bench Frame. 8 17 6 18 To use the Backrest (18) in an inclined position, pull the Seat Knob (36) out as far as it will go and move the Seat (20). Engage the Knob into one of the three adjustment holes in the Bench Frame (2) that are closest to the Upright Base (6). Rest the Backrest Frame (17) on the bracket on the Upright Base, or against the Left and Right Uprights (8, 9). 2 36 Adjustment Holes REMOVING THE BACKREST 17 To remove the Backrest (18), raise the Backrest Frame (17) so that it stands directly over the Seat Frame (19). Lift the Backrest Frame straight up and out of the Seat Frame so the indicated bar disengages the Seat Frame. 18 19 12 Bar 21 ADJUSTING THE SEAT To allow the Seat (20) to roll up and down the Bench Frame (2), remove the backrest from the Seat Frame (see REMOVING THE BACKREST on page 12). Pull the Seat Knob (36) out as far as it will go, and turn the Knob so that the pin rests at the end of the “L”slot (see the inset drawing). 20 “L”-Slot 36 ATTACHING THE ACCESSORIES TO THE HIGH OR LOW PULLEY STATIONS The Handles (45) can be attached to the Medium Nylon Ropes (52) with two Cable Clip (31). 36 2 Pin 19 52 31 The Handles (45) and the Ankle Strap (not shown) can be attached to the Long Nylon Rope (not shown) in the same manner. 52 31 45 When using the Leg Press Strap (not shown), attach one side to the left end of the Long Nylon Rope (not shown), and the other side to the right end of the Long Nylon Rope, with two Cable Clips (31). 45 ADJUSTING THE RESISTANCE To change the amount of resistance, squeeze the resistance handle so that the pin on the Left Handle (26) disengages the Resistance Bracket (not shown). Line up the resistance handle with the number on the Left Cover (10) corresponding to the desired amount of resistance, and release the handle. Be sure that the pin on the Left Handle engages a hole in the Resistance Bracket. 11 Resistance Handle 26 Numbers 10 Note: If you have purchased an optional GOLD’S GYM MAX PACK, a decal should have been placed on the Right Cover (11). This decal indicates the amount of resistance at each resistance handle position, when one or two sets of exterior bands have been attached to the resistance system. (To attach the exterior bands see ATTACHING EXTERIOR BANDS, on page 14.) Note: The resistance system uses progressive resistance. As the bands begin to stretch, the amount of resistance will increase gradually. As the bands stretch further, the resistance will increase rapidly. 13 STORING THE RESISTANCE SYSTEM To store the resistance system, secure the Seat Knob (36) into the adjustment hole in the Bench Frame (2) that is closest to the Leg Developer (21) (see ADJUSTING THE BACKREST on page 12). Remove the indicated Bench Knob (41) from the Base (4) and lift the Leg Developer so that it rests against the Left and Right Uprights (8, 9). Engage the Knob into the indicated hole in the Base. 9 21 8 36 2 ATTACHING EXTERIOR BANDS Remove the 1/2” x 1” Button Screw (110) with the 1/2” Small Washer (82) from each side of the resistance system. Remove the Side Covers (42) from the Left and Right Covers (10, 11). Remove the 1/2” x 1” Button Screw with the 1/2” Washer (106) from each side of the resistance system. 4 41 Slide the four 17.5mm Spacers (A) onto the four Resistance Rods (B). (See the inset drawing for correct orientation.) Slide the two removed 1/2” Washers (106) onto two of the Rods. Attach a Resistance Rod (B) and a Resistance Rod with a 1/2” Washer (106) to the indicated locations on the resistance system. Attach the other two Resistance Rods to the other side of the resistance system. B 11 Slide an Exterior Band (C) onto each set of Resistance Rods (B). For more resistance, add a second Band to each set of Rods. Note: It may be necessary to stretch the Bands to slide them onto the Rods. Secure the Exterior Bands with the two Clips (D). A 106 A IMPORTANT: Always place the same number of Exterior Bands (C) on each side of the resistance system. Use only the Bands included with a GOLD’S GYM MAX PACK. Always secure the Bands with the Clips (D). 110 14 B A 10 To purchase a MAX PACK, call our Customer Service Department at the number listed on the front cover of this manual. The MAX PACK shown is model number GGMC0921. Small Hole Large Hole A 82 B C D 42 110 PART LIST—Model No. GGSY2921.0 Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 4 1 1 1 2 2 5 4 2 1 1 1 6 4 1 1 2 2 1 1 2 5 8 8 5 11 3 2 1 1 2 2 4 2 4 4 Description Front Leg Bench Frame Base Stabilizer Base Base Cover Upright Base Upright Stabilizer Left Upright Right Upright Left Cover Right Cover Left Arm Right Arm Pulley Arm Resistance Bracket Resistance Leg Backrest Frame Backrest Seat Frame Seat Leg Developer Leg Lever Pivot Bracket Left Resistance Plate M8 x 25mm Patch Screw Left Handle Right Handle “U”-Bracket Band Resistance Wheel Cable Clip 13.5mm Spacer Inner Resistance Rod Upright Cover 6000ZZ Bearing Seat Knob Seat Wheel Foam Pad Front Bench Frame Plate Rear Bench Frame Plate Bench Knob Side Cover Leg Press Strap Ankle Strap Handle Plastic Foot Pulley Arm Bushing Pulley Bushing “V”-Pulley 3 1/2” Pulley Cable Trap Medium Nylon Rope Long Nylon Rope Short Nylon Rope 45mm Round Inner Cap 2” Round Inner Cap 1” Square Inner Cap Frame Inner Cap 57.1mm Round Outer Cap 19mm Round Inner Cap Key No. Qty. 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 # # 4 2 1 1 1 1 4 6 6 4 8 15 6 14 2 2 2 1 2 1 1 2 4 1 7 14 1 1 4 4 1 1 2 2 1 1 1 1 6 7 2 1 2 14 1 2 1 2 1 4 2 1 1 1 1 1 2 1 1 1 R1005A Description 50.8mm Round Inner Cap Wheel Eyebolt Resistance Spacer Upright Spacer M6 Zinc Nut M6 x 16mm Screw 11.1mm Spacer M6 Washer M10 Split Washer M8 Black Nylon Locknut M10 Nylon Locknut M6 Zinc Nylon Locknut M8 x 25mm Button Screw M8 x 38mm Carriage Bolt M8 x 70mm Carriage Bolt M6 x 72mm Bolt M10 x 69mm Bolt M10 x 40mm Bolt M10 x 127mm Bolt M10 x 215mm Bolt 1/2” Small Washer M10 x 25mm Button Screw M10 x 94mm Bolt M4 x 25mm Screw M4 x 16mm Screw Bench Leg Bushing M10 x 107mm Bolt M10 x 60mm Button Bolt M6 x 38mm Screw M10 x 69mm Bolt M10 x 83mm Bolt M10 x 17mm Hex Screw M6 x 23mm Bolt M6 x 50mm Bolt M6 x 40mm Bolt M10 x 75mm Bolt M10 x 50mm Shoulder Bolt M6 Shoulder Bolt M6 Black Nylon Locknut M8 x 64mm Bolt M4 x 12mm Screw M6 x 16mm Screw M8 Split Washer M8 Zinc Nylon Locknut 1/2” Washer M10 Nylon Jamnut M4 x 16mm Tec Screw Spring 1/2” x 1” Button Screw M8 x 25mm Button Bolt M10 x 25mm Bolt Steel Wheel 608Z Bearing Seat Backing Backrest Backing Shear Protector Right Resistance Plate User’s Manual Exercise Guide Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 39 72 59 86 105 38 104 74 58 60 1 59 2 54 88 104 74 54 38 41 49 86 22 21 67 73 99 73 41 60 56 91 56 72 104 74 86 38 23 104 60 74 115 37 99 68 68 37 73 68 37 99 73 19 73 67 99 100 72 63 31 55 38 87 55 60 73 36 37 99 37 68 103 20 92 86 40 58 18 101 3 46 86 57 75 71 46 86 85 71 31 53 61 69 116 46 86 25 48 4 5 83 46 86 86 72 47 85 85 52 49 42 86 70 83 69 102 47 13 90 48 14 89 85 72 47 71 25 49 90 69 17 69 46 57 31 52 61 78 48 89 72 51 108 48 14 50 79 85 47 50 79 6 11 9 72 72 34 104 71 71 72 74 65 104 74 8 31 49 50 81 108 72 61 84 59 52 10 100 86 7 97 51 62 50 107 72 77 48 89 14 47 47 48 85 15 28 31 49 83 86 70 86 12 53 47 83 52 77 80 30 51 117 59 62 106 66 100 76 50 95 110 82 89 48 14 29 61 47 44 32 93 42 100 113 72 32 16 33 48 72 29 32 71 118 64 24 114 45 30 43 117 32 110 110 106 82 94 111 26 96 109 98 112 69 33 100 35 93 27 EXPLODED DRAWING—Model No. GGSY2921.0 R1005A ORDERING REPLACEMENT PARTS To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give the following information: 1. the MODEL NUMBER of the product (GGSY2921.0) 2. the NAME of the product (GOLD’S GYM POWER FLEX resistance system) 3. the SERIAL NUMBER of the product (see the front cover of this manual) 4. the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST in the center of this manual) LIMITED WARRANTY WHAT IS COVERED—The entire GOLD’S GYM POWER FLEX resistance system (“Product”) is warranted to be free of all defects in material and workmanship. WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser. HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product frame for the lifetime of the original owner. ICON warrants all other parts for one year after the date of purchase. Labor is covered for ninety days. WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our option, we will replace the Product. WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper assembly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and maintain as set out in your User’s Manual (“Manual”). WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair. USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction. HOW TO GET PARTS AND SERVICE—Simply call the toll-free phone number on the front cover of this manual and tell them your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered by warranty. ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you. No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and you may have other rights which vary from state to state. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813 Part No. 180550 R1005A Printed in China © 2002 ICON IP, Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 17 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (PANTONE 877 C).%%+ (PANTONE 871 C).%%+ (PANTONE 151 C).%%CMYKCustomColor: 0 0 0 .4 (PANTONE 877 C).%%+ .2 .25 .6 .25 (PANTONE 871 C).%%+ 0 .48 .95 0 (PANTONE 151 C).%%EndComments Producer : QuarkXPress(tm) 6.5 Create Date : 2005:10:21 16:21:10 Title : GGSY29210-180550 Creator : QuarkXPress(tm) 6.5EXIF Metadata provided by EXIF.tools