Gospell Smarthome Electronic GB8209 Baby Monitor (Transmitter) User Manual 8209AW

Shenzhen Gospell Smarthome Electronic Co., Ltd. Baby Monitor (Transmitter) 8209AW

Users Manual

Contents1. Packing List2. Diagram3. Structure4. Installation5. Specification6. FCC and EU112389
1. Packing List2. DiagramSensor for camera* 8209AW means GB8209 + GB7609
3. Structure3-1. Structure of Camera3-2. Structure of ReceiverAntennaAntennaSpeakerIR LEDsTFT-LCDPower On/OffAlarmSwitchSensitivitySwitchChannel SwitchBattery CoverBattery CoverLensPower SocketChannel IndicatorAV OutVolumeSwitchPowerOn/OffSleep Button Power SocketSensor SocketChannel ButtonEliminateAlarmButton
4. Installation4-1. Installation of Camera4-1-1. Basic installation of Camera2. Connect the camera to the adapter and then slide the power switch to ON position. Note: This camera can also use dry battery as power supply. Please load 4 AA batteries to the battery compartment at the back of camera with their polarities matched. The AC adapter will work instead of batteries after it is plugged. If the camera is not used for a long period of time, please unplug the adapter and remove the batteries. Avoid short circuit of the battery. * Continue working for 5 hours(IR OFF)
3. Rotate the rounded head of camera to a suitable angle for surveillance. 1. Check out the right side of the camera and there is the channel switch marked as CH1, CH2, CH3, CH4. Each of them can be selected separately for the purpose of the multi-camera working situation or interference avoidance.2. Press channel button of the receiver to select the same channel as the camera, The pictures will be displayed on the screen.30304-1-2. Camera channel setup4-1-3. Camera alarm setupCH4 CH3 CH2 CH1Off Motion Sensor SoundLow Middle HighCh1: 2,414MHzCh2: 2,432MHzCh3: 2,450MHzCh4: 2,468MHz1. The camera provides Motion Detection, Sensor Detection, SoundDetection. Each mode can separately be selected by 3 sensitivity levelsas Low, Middle, High. AlarmSensitivity
2. Connect the sensor jack to the camera sensor socket, put the sensor end in cotton diaper if you select the Bed-wetting Sensor detection.* Specialists recommend the sensor is not suitable for disposable panty diaper; and not suitable for touching skin directly.Motion Alarm Setup:It refers to the alarm against various movements. If you slide the alarm setting switch to Motion position, and select Sensitivity switch. Afterward, the system enters the motion alarm mode. Whena movement is actually detected, the alarm begins until you pressthe Eliminate Alarm Button. After less than 1 minute, the motionalarm enters the next alarm circle.Sound Alarm Setup:It refers to the alarm against sound . If you slide the alarm setting switch to Sound position, and select Sensitivity switch. Afterward, the system enters the sound alarm mode. When the sound is actually detected, the alarm begins until you press the Eliminate Alarm Button. After less than 1 minute, the sound alarm enters the next alarm circle. Sensor Alarm Setup:It refers to the alarm against bedwetting. If you slide the alarm setting switch to Sensor position, and select Sensitivity switch. Connect the sensor to camera and diaper. Afterward, the system enters the sensor alarm mode. When the bedwetting and water is actually detected, the alarm begins until you press the Eliminate Alarm Button. After less than 1 minute, the motion alarm enters the next alarm circle.Off Alarm Setup:It refers to the abandonment of the alarm function. If you slide the alarm setting switch to Off position. The alarm function is disabled. Note:When the camera is powered on by dry batteries and directly pluggedin by the adapter, the alarm function fails to work. If this is the case,please slide the power Off and back again to On, the alarm functionis successfully activated.
4-2. Installation of Receiver4-2-1. Basic installation of Receiver1. Connect the receiver to the adapter and then slide the power switch to ON position. 2. Adjust the volume control to a desired level.Note: This receiver can also work on dry battery. Please load 4 AA batteries to the battery compartment at the back of receiver with their polarities matched. The AC adapter will work instead of batteries after it is plugged. If the receiver is left unused for a long period of time, please unplug the adapter and remove the batteries. Avoid short circuit of the battery. * Continue working for 5 hours
3. Set the channel of receiver to be the same as camera by pressing the channel button continuously, and the pictures will display on the screen.Note: For more clear pictures, please connect the receiver to a monitor/TVwith AV cable (yellow for video and red for audio).AV cable1. Volume adjustment Slide Volume Switch to adjust the volume of the receiver.2. Channel selection Press CH button to select the appropriate channel.3. Channel Looping Hold the CH button for three seconds to enter the loop mode. All the available channels will be displayed one by one (default interval is 5 seconds).4. Sleep Mode Press the Sleep Button to shut down the LCD display and keep the voice function. Press the button again and recall the normal working mode. It can save energy and help your sleeping.5. Eliminate Alarm button Press Eliminate Alarm button to eliminate alarm voice . Less than 1 minute, the alarm enters again next circle automatically. 4-2-2. Operation of Receiver
5. SpecificationCAMERARECEIVER GENERALItem ValueTransmission FrequencyTransmission PowerOperating FrequencyUnobstructed Effective RangeModulation ModeOperating TemperatureOperating HumidityImaging Sensor TypePicture Total PixelsMinimum IlluminationNight Vision DistanceBandwidthBattery Working TimeMotion Alarm DistanceSound Detection SensitivityConsumption Current(Max.)Power SupplyDimensions(W D H)Weight(About)LCD Screen TypeEffective PixelsReceiving SensitivityConsumption Current(Max.)Battery Working TimePower SupplyDimensions(W D H)Weight(About)ISM 2,400~2,483 MHz10mW/CE; 2mW/FCC2,414MHz; 2,432MHz;2,450MHz; 2,468MHz100m(Min.)FM-10 ~ +50 / +14 ~ +12285%CMOSPAL: 720 480Pixels;NTSC: 724 576 Pixels0Lux (IR ON)5m18M5 hours (IR Off)5m>63dBDC+8V/500mA86 48 135 mm 146g 2.4 TFT-LCD480 240-85dBm200mA5 hoursDC+8V/500mA 86 54 143 mm142 g120mA(IR OFF) & 220mW(IR ON)
6. FCC informationThis device complies with part15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment. Any change to the equipment will void FCC grant. This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. The equipment compliance with FCC radiation exposure limit set forth for uncontrolled Environment

Navigation menu