Graco Inc 245924 Users Manual 311777D, Texture Guns, US English
245924 to the manual 35e86aa7-4570-4212-8e16-8fdd513297f1
2015-02-09
: Graco-Inc Graco-Inc-245924-Users-Manual-561100 graco-inc-245924-users-manual-561100 graco-inc pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Texture Guns Models: 288628, 288629, and 245924 English 125 psi (8.75 bar, 0.875 MPa) Maximum Air Working Pressure 70 psi (4.9 bar, 0.49 MPa) Maximum Fluid Working Pressure IMPORTANT SAFETY INSTRUCTIONS. Refer to your sprayer instruction manual for Pressure Relief, priming and spray instructions. Keep these instructions. 311777D Model 288628, no hopper Model 245924, with hopper Model 288629 ti8808a ti8508a - For Water-Based Materials Only The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. EQUIPMENT MISUSE HAZARD WARNINGS PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure in this manual when you stop spraying and before cleaning, checking, or servicing equipment. • Tighten all fluid connections before operating the equipment. • Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. FIRE AND EXPLOSION HAZARD Repair Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • Use equipment only in well ventilated area. • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc). • Keep work area free of debris, including solvent, rags and gasoline. • Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present. • Ground all equipment in the work area. See Grounding instructions. • Use only grounded hoses. • Hold gun firmly to side of grounded pail when triggering into pail. • If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem. • Keep a working fire extinguisher in the work area. Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001 Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Use fluids that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not kink or over bend hoses or use hoses to pull equipment. • Keep children and animals away from work area. • Comply with all applicable safety regulations. PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or in the operating area of the equipment to help protect you from serious injury. This equipment includes but is not limited to: • Protective eyewear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection Pressure Relief Procedure 9. Remove plug and use small screwdriver to remove all components out front of gun. WARNING Follow this Pressure Relief Procedure whenever you are instructed to relieve pressure, stop spraying, check or service equipment or install or clean spray ti8806a ti8807a tip. 1. Turn OFF power and turn sprayer pressure control to lowest pressure setting. 2. Trigger gun into pail to relieve pressure. Assembly 1. Hold gun as shown and insert spring in front of gun. Cleaning and Lubricating Disassemble needle assembly and clean and grease o-rings regularly to prolong gun life. Disassembly ti9271a 1. Perform Pressure Relief Procedure (see above). 2. Remove hopper or material hose from gun. 3. Clean off as much material on gun body as possible. 4. Turn flow adjustment nut counter-clockwise to enable trigger to have full range of travel. 2. Insert spring guide with o-ring into flow adjustment nut. Make sure the protruded end of the guide points out as shown. 3. Position flow adjustment nut in seat on gun body. 4. Apply a generous amount of grease to o-rings. 5. Rest gun on air connection fitting. Slide needle into front of gun. ti8539a 5. Using a small flat screwdriver, pry retaining ring off of trigger pin. Remove pin, washer, and trigger. ti8538a 6. While pushing needle into gun, turn flow adjustment nut counter-clockwise to tighten needle. 7. Pull back on flow adjustment nut or continue pushing needle in to make room for trigger. ti8530a 6. Unscrew nozzle and remove it from gun. ti8532a 8. Insert pin through trigger and washers. Push the retaining clip onto the pin. ti9273a 7. Hold needle securely in place so it does not turn while turning flow control clockwise until needle is disengaged from thread and released. Pull needle and o-rings out front of gun. 8. Hold hand under trigger area to catch adjustment nut, spring retainer, and spring. Tap gun lightly to loosen spring or use a small screwdriver to loosen. ti8530a 9. Pull trigger and replace nozzle. ti9272a ti8538a 2 311777D Parts Model 288628 and 245924 27 Model 288629 3c 3e 3f 31 3d 3a 3d 3b 33 1B 6 10 8 20 (a,b,c,d) 21 9 21 32 22 ti8509a 16a 26 16c 20 3d 3c 21 3a 3d 2 3a 3b 3c 3d 3e 3f 6 8 8a 8b 8c 8d 15B168 234153 311777D 22 1A 10 6 16b 8 (a,b,c,d) Part 288628 288629 277393 277394 15F913 258000 2 27 3b 21 Ref. A B 1A 1B 2 3 3e 3f ti8524a 9 Description GUN, complete, (for use with hopper) GUN, complete, (non-hopper) BODY, gun BODY, gun TRIGGER, gun, trigger KIT, needle, repair includes 3a, 3b, 3c, 3d, 3e, 3f NEEDLE, includes o-ring NUT, flow adjuster GUIDE, needle O-RING SPRING TAPE, foam LOCK, trigger KIT, nozzle, includes 8a, 8b, 8c, 8d NOZZLE, fine, beige NOZZLE, small, white NOZZLE, medium, gray NOZZLE, large, black Qty 1 1 1 1 1 1 1 1 Ref. 9 10 16 16a 16b 16c 20 21 22 26 27 31 32 33 Part 169970 15B565 234162 118717 107243 115999 287967 15J635 234225 234188 234222 Description FITTING, line air VALVE, ball KIT, plug, includes 16a, 16b, 16c PLUG, hopper PLUG, hose, port O-RING PIN, clevis w/ring groove WASHER RING, retaining PIN, clip gun PLUG KIT, hopper, 1.5 gallon (includes 32) CLAMP KIT, hopper, 0.75 gallon (includes 32) Qty 1 1 1 1 2 1 1 1 1 1 Technical Data Air Consumption 3.5-11 cfm at 15 to 100 psi Weight 35 oz (1600 g) 3 All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. This manual contains English. MM 311777 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 www.graco.com 311777D Revised 09/2007
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Mode : UseNone XMP Toolkit : 3.1-701 About : uuid:5c2ada77-694e-4989-b0de-daf3a16780be Web Statement : Texture Guns, 311777D Producer : Acrobat Distiller 6.0.1 (Windows) Keywords : 311777D, Texture Guns, US English Job Ref : Z033300 Copyright : 2006, Revised 9/2007 Creator Tool : FrameMaker 7.1 Modify Date : 2009:10:15 16:16:20-05:00 Create Date : 2004:10:18 09:44:46Z Metadata Date : 2009:10:15 16:16:20-05:00 Document ID : uuid:d7bcfe63-769d-437a-970e-53ceb11ec6ff Instance ID : uuid:070bee49-d1b1-4460-bd9f-b341f38a51c4 Format : application/pdf Description : 311777D, Texture Guns Title : 311777D, Texture Guns, US English Creator : Emil Meindl Page Count : 4 Subject : 311777D, Texture Guns Author : Emil MeindlEXIF Metadata provided by EXIF.tools