Graco Inc 311365G Users Manual Ultra Max II/Ultimate Mx II, Repair, English
ti13459a to the manual c4958915-56ad-453b-9af7-c89a107a4891
2015-02-09
: Graco-Inc Graco-Inc-311365G-Users-Manual-561349 graco-inc-311365g-users-manual-561349 graco-inc pdf
Open the PDF directly: View PDF 
.
Page Count: 43
| Download | |
| Open PDF In Browser | View PDF |
Repair Ultra® Max II/Ultimate Mx II 311365G Korean patent10-0579681 - For Portable Airless Spraying of Architectural Coatings and Paints IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions in this manual. Save these instructions. ti13459a 695/795 LOW ti13450a 695/795 HI ti13460a 1095/1595 HI ti13461a MARK V Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001 Table of Contents Table of Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Component Identification and Function . . . . . . . . 7 General Repair Information . . . . . . . . . . . . . . . . . . 8 Pressure Relief Procedure . . . . . . . . . . . . . . . . . 8 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mechanical/Fluid Flow . . . . . . . . . . . . . . . . . . . . 10 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Pressure Control Board . . . . . . . . . . . . . . . . . . . . 16 100 - 120 Vac North American and Japan/Taiwan Motor Control Board . . . . . . 16 240 Vac Motor Control Board . . . . . . . . . . . . . . 18 240 Vac Filter Board . . . . . . . . . . . . . . . . . . . . . 19 110 Vac U.K. Motor Control Board . . . . . . . . . . 20 110 Vac U.K. Filter Board . . . . . . . . . . . . . . . . . 20 Pressure Adjust Potentiometer . . . . . . . . . . . . . 22 Pressure Control Transducer . . . . . . . . . . . . . . 23 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Drive and Bearing Housing Replacement . . . . . . 26 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Motor Replacement . . . . . . . . . . . . . . . . . . . . . . . . 28 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Displacement Pump Replacement for 695/795 . . 30 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Displacement Pump Replacement 1095/1595/Mark V . . . . . . . . . . . . . . . . . . . . . . 32 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 36 2 311365G Models Models Vac 120 North America Model Type Lo-Boy Hi-Boy 695 Standard 255130 249642 Premium 255131 249644 Standard 255132 249646 Premium 255133 249648 795 1095 1595 Standard 249651 Premium 249653 Standard 253060 Premium 253059 Mark V 120 North America 1595 249904 Standard 249658** Premium 249659** Mark V 695 Ultimate Mx II 795 1095 1595 Ultimate Mx II 1595 695 240 Europe 249903** Standard 826093 826067 Premium 826094 826069 Standard 826071 Premium 826072 Standard 826073 Premium 826074 Standard 826082 Premium 826081 Standard 826075 Premium 826076 255134 256165 249667 249905 Mark V 110 UK 240 Asia 311365G 695 249663 249666 795 1095 240 Europe Multi-cord 256166 255135 249668 795 249671 1095 249672 Mark V* 249907 695 249673 795 249674 1095 249675 Mark V 249906 695 *Also for Asia and Australia; **Not ETL Approved All models not available in all countries. 255138 249681 795 249683 1095 249684 3 Models Vac Model 240 Australia Type Lo-Boy Hi-Boy 695 255139 249685 795 255140 249687 1095 100 Japan & Taiwan 695 255136 249676 795 255137 249678 1095 4 249688 249680 311365G Warnings Warnings The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. Grounding Instructions This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING GROUNDING • Improper installation of the grounding plug is able to result in a risk of electric shock. • When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade terminal. • The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire. • Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or when in doubt as to whether the product is properly grounded. • Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electrician. • This product is for use on a nominal 120V circuit and has a grounding plug similar to the plug illustrated in the figure below. ti9164a • • Only connect the product to an outlet having the same configuration as the plug. Do not use an adapter with this product. Extension Cords: • Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that accepts the plug on the product. • Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG (2.5 mm2) minimum to carry the current that the product draws. • An undersized cord results in a drop in line voltage and loss of power and overheating. 311365G 5 Warnings WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors, and electrical equipment. • Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose assembly, spray gun, and objects in and around the spray area shall be properly grounded to protect against static discharge and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses. • Verify that all containers and collection systems are grounded to prevent static discharge. • Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter. • Do not use a paint or a solvent containing halogenated hydrocarbons. • Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump assembly in a well ventilated area. Do not spray pump assembly. • Do not smoke in the spray area. • Do not operate light switches, engines, or similar spark producing products in the spray area. • Keep area clean and free of paint or solvent containers, rags, and other flammable materials. • Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and container labels provided with the paints and solvents. Follow the paint and solvents manufacturer’s safety instructions. • Fire extinguisher equipment shall be present and working. • Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors. SKIN INJECTION HAZARD • Do not aim the gun at, or spray any person or animal. • Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with any part of the body. • Always use the nozzle tip guard. Do not spray without nozzle tip guard in place. • Use Graco nozzle tips. • Use caution when cleaning and changing nozzle tips. in the case where the nozzle tip clogs while spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure before removing the nozzle tip to clean. • Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn off the unit and follow the Pressure Relief Procedure for turning off the unit. • High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment. • Check hoses and parts for signs of damage. Replace any damaged hoses or parts. • This system is capable of producing 3300 psi. Use Graco replacement parts or accessories that are rated a minimum of 3300 psi. • Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly. • Verify that all connections are secure before operating the unit. • Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls. 6 311365G Warnings WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Always wear appropriate gloves, eye protection, and a respirator or mask when painting. • Do not operate or spray near children. Keep children away from equipment at all times. • Do not overreach or stand on an unstable support. Keep effective footing and balance at all times. • Stay alert and watch what you are doing. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not kink or over-bend the hose. • Do not expose the hose to temperatures or to pressures in excess of those specified by Graco. • Do not use the hose as a strength member to pull or lift the equipment. ELECTRIC SHOCK HAZARD Improper grounding, setup, or usage of the system can cause electric shock. • Turn off and disconnect power cord before servicing equipment. • Use only grounded electrical outlets. • Use only 3-wire extension cords. • Ensure ground prongs are intact on sprayer and extension cords. • Do not expose to rain. Store indoors. PRESSURIZED ALUMINUM PARTS HAZARD Do not use 1, 1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage. MOVING PARTS HAZARD Moving parts can pinch or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply. PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to: • Protective eye wear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection 311365G 7 Component Identification and Function Component Identification and Function 12. 11. 10. ti13451a 9. 5. 6. 7. 8. English Premium Digital Display ON/OFF switch Pressure control Prime / Spray valve Filter 1 2 3 4 5 6 AutoClean ™ 2 7 Siphon tube 8 Pump 9 Bearing Housing / ProConnect™ 10 Fluid Outlet 11 Drain tube 12 Trigger Lock 13 Model/serial tag 14 WatchDog™ Switch (not Mark V) 8 311365G General Repair Information General Repair Information Pressure Relief Procedure CAUTION To reduce risk of pressure control malfunction: SKIN INJECTION HAZARD System pressure must be manually relieved to prevent system from starting or spraying accidentally. Fluid under high pressure can be injected through skin and cause serious injury. To reduce risk of injury from injection, splashing fluid, or moving parts, follow Pressure Relief Procedure whenever you: • are instructed to relieve pressure • stop spraying • check or service any system equipment • install or clean spray tip • Use needle-nose pliers to disconnect wire. Never pull on wire, pull on connector. • Mate wire connectors properly. Center flat blade of insulated male connector in female connector. • Route wires carefully to avoid interference with other connections of pressure control. Do not pinch wires between cover and control box. 1. Keep all screws, nuts, washers, gaskets, and electrical fittings removed during repair procedures. These parts are not normally provided with replacement assemblies. 1. Turn pressure control knob to zero. 2. Turn ON/OFF switch to OFF. 3. Unplug power supply cord. 4. Hold metal part of gun firmly to grounded metal pail. Trigger gun to relieve pressure. 5. Lock gun safety latch. 6. Open prime valve. Leave prime valve open until ready to spray again. If suspected that spray tip or hose is completely clogged, or that pressure has not been fully relieved after following steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Then clear tip or hose obstruction. 311365G ELECTRIC SHOCK HAZARD MOVING PARTS HAZARD HOT SURFACE HAZARD To reduce risk of serious injury, including electric shock, do not touch moving or electrical parts with fingers or tools while testing repair. Shut off and unplug sprayer when inspection is complete. Install all covers, guards, gaskets, screws, washers and shroud before operating sprayer. 2. Test repair after problem is corrected. 3. If sprayer does not operate properly, review repair procedure to verify procedure was done correctly. If necessary, see Troubleshooting, page 11, for other possible solutions. 9 Grounding Grounding 2. Do not alter ground prong or use adapter. ti2810a WARNING Improper installation or alteration of grounding plug results in risk of electric shock, fire or explosion that could cause serious injury or death. 1. Ultra Max II 695, 795 and 1095 100-200 Vac models require a 50/60 Hz, 15A circuit with a grounding receptacle. Ultra Max II 1595/Mark V 120 Vac models require a 50/60 Hz 20A circuit with a grounding receptacle; 220-240 Vac models require a 50/60 Hz, 10A circuit with a grounding receptacle. 10 3. 120 Vac: A 12 AWG, 3 wires with grounding prong, 300 ft (90 m) extension cord may be used. 220-240 Vac: You may use a 3-wire, 1.0 mm (12 AWG) (minimum) extension cord up to 90 m long. Long lengths reduce sprayer performance. 311365G Troubleshooting Troubleshooting Mechanical/Fluid Flow Relieve pressure; page 9. TYPE OF PROBLEM WHAT TO CHECK If check is OK, go to next check WHAT TO DO When check is not OK, refer to this column E=XX is displayed 1. Fault condition exists 1. Determine fault correction from table, page 13. False tripping of WatchDog system. EMPTY is displayed. Pump does not run. 1. Operating conditions out of WatchDog parameters. Pump output is low, see below. 1. Turn pressure down. Refer to operation manual for adjusting. Operate without WatchDog active; see operation manual. Pump output is low 1. Spray tip worn 1. Follow Pressure Relief procedure Warning, then replace tip. See your separate gun or tip manual. 2. Spray tip clogged 2. Relieve pressure. Check and clean spray tip. 3. Paint supply 3. Refill and reprime pump. 4. Intake strainer clogged 4. Remove and clean, then reinstall 5. Intake valve ball and piston ball are not seating properly 5. Remove intake valve and clean. Check balls and seats for nicks; replace if necessary; see pump manual 310643 or 310894. Strain paint before using to remove particles that could clog pump. 6. Suction hose connections 6. Tighten any loose connections. Check for missing or damaged seals. 7. Fluid filter, tip filter, or tip is clogged or dirty. 7. Clean filter; see operation manual. 8. Prime valve leaking 8. Relieve pressure. Repair prime valve. 9. Verify pump does not continue to 9. Service pump; see pump manual 310643 or 310894. stroke when gun trigger is released. (Prime valve not leaking.) 311365G 10. Leaking around throat packing nut which may indicate worn or damaged packings. 10. Replace packings; see pump manual. Also check piston valve seat for hardened paint or nicks and replace if necessary. Tighten packing nut/wet-cup. 11. Pump rod damage 11. Repair pump. See pump manual 310643 or 310894. 12. Low stall pressure 12. Turn pressure knob fully clockwise. Make sure pressure control knob is properly installed to allow full clockwise position. If problem persists, replace pressure transducer. 13. Piston packings are worn or damaged 13. Replace packings; see pump manual 310643 or 310894. 11 Troubleshooting TYPE OF PROBLEM Pump output is low WHAT TO CHECK If check is OK, go to next check WHAT TO DO When check is not OK, refer to this column 14. O-ring in pump is worn or damaged 14. Replace o-ring; see pump manual 310643 or 310894. 15. Intake valve ball is packed with material 15. Clean intake valve; see pump manual 310643 or 310894. 16. Pressure setting is too low 16. Increase pressure; see pump manual 310643 or 310894. 17. Large pressure drop in hose with 17. Use larger diameter hose and/or reduce heavy materials overall length of hose. Use of more than 100 ft of 1/4 in. hose significantly reduces performance of sprayer. Use 3/8 in. hose for optimum performance (50 ft minimum). Motor runs but pump does not stroke 1. Displacement pump pin (32) damaged or missing; see pump manual 310643 or 310894. 1. Replace pump pin if missing. Be sure retainer spring (31) is fully in groove all around connecting rod; see pump manual 310643 or 310894. 2. Connecting rod assembly (43) damaged; see pump manual 310643 or 310894. 2. Replace connecting rod assembly; see pump manual 310643 or 310894. 3. Gears or drive housing damaged, 3. Inspect drive housing assembly and gears page 30. for damage and replace if necessary; see pump manual 310643 or 310894. Excessive paint leakage into 1. Throat packing nut is loose throat packing nut Fluid is spitting from gun Pump is difficult to prime 2. Throat packings are worn or damaged 2. Replace packings; see pump manual 310643 or 310894. 3. Displacement rod is worn or damaged 3. Replace rod; see pump manual 310643 or 310894. 1. Air in pump or hose 1. Check and tighten all fluid connections. Reduce engine speed and cycle pump as slowly as possible during priming. 2. Tip is partially clogged 2. Clear tip; see tip guard manual 309640. 3. Fluid supply is low or empty 3. Refill fluid supply. Prime pump; see pump manual 310643 or 310894. Check fluid supply often to prevent running pump dry. 1. Air in pump or hose 1. Check and tighten all fluid connections. Reduce engine speed and cycle pump as slowly as possible during priming. 2. Intake valve is leaking 2. Clean intake valve. Be sure ball seat is not nicked or worn and that ball seats well. Reassemble valve. 3. Pump packings are worn 3. Replace pump packings; see pump manual 310643 or 310894. 4. Paint is too thick 4. Thin the paint according to the supplier’s recommendations. No display, sprayer operates 1. Display is damaged or has bad connection 12 1. Remove throat packing nut spacer. Tighten throat packing nut just enough to stop leakage. 1. Check connections. Replace display. 311365G Troubleshooting Electrical Symptom: Sprayer does not run or stops running. Relieve pressure; page 9. WARNING • Plug sprayer into correct voltage, grounded outlet • Set power switch OFF for 30 seconds and then ON again. This ensures sprayer is in normal run mode. • Turn pressure control knob clockwise 1/2 turn • View digital display TYPE OF PROBLEM Sprayer does not run at all To avoid electrical shock or moving parts hazards when covers are removed for troubleshooting, wait 30 seconds after unplugging power cord for stored electricity to dissipate. Keep clear of electrical and moving parts during troubleshooting procedures. If no digital display is available, use control board status light to troubleshoot problems: Turn ON/OFF switch OFF, remove control cover and then turn power back ON. Observe status light. Blinking LED total count equals digital error code i.e., two blinks equals E=02. WHAT TO CHECK HOW TO CHECK See flow chart, page 19. Digital display is blank Control board status light never lights Sprayer does not run at all Digital display shows E=02 Control board status light blinks 2 times repeatedly 311365G Check transducer or transducer connections 1. Make sure there is no pressure in the system (see Pressure Relief, page 9). Check fluid path for clogs, such as clogged filter. 2. Use airless paint spray hose with no metal braid 1/4 in. x 50 ft minimum. Smaller hose or metal braid hose may result in high-pressure spikes. 3. Set sprayer to OFF and disconnect power to sprayer. 4. Check transducer and connections to control board. 5. Disconnect transducer from control board socket. Check that transducer and control board contacts are clean and secure. 6. Reconnect transducer to control board socket. Connect power, set sprayer ON and control knob 1/2 turn clockwise. If sprayer does not run properly, set sprayer to OFF and go to next step. 7. Install new transducer. Connect power, set sprayer ON and control knob 1/2 turn clockwise. Replace control board if sprayer does not run properly. 13 Troubleshooting TYPE OF PROBLEM Sprayer does not run at all Digital display shows E=03 Control board status light blinks 3 times repeatedly 14 WHAT TO CHECK Check transducer or transducer connections (control board is not detecting a pressure signal). HOW TO CHECK 1. Set sprayer to OFF and disconnect power to sprayer. 2. Check transducer and connections to control board. 3. Disconnect transducer from control board socket. Check to see if transducer and control board contacts are clean and secure. 4. Reconnect transducer to control board socket. Connect power, set sprayer ON and control knob to 1/2 turn clockwise. If sprayer does not run, set sprayer to OFF and go to next step. 5. Connect a confirmed working transducer to control board socket. 6. Set sprayer ON and control knob to 1/2 turn clockwise. If sprayer runs, install new transducer. Replace control board if sprayer does not run. 7. Check transducer resistance with ohmmeter (less than 9k ohm between red and black wires and 3-6k ohm between green and yellow wires). 311365G Troubleshooting TYPE OF PROBLEM Sprayer does not run at all Digital display shows E=05 WHAT TO CHECK HOW TO CHECK Control is commanding motor to run 1. but motor shaft does not rotate. Possibly locked rotor condition, an open connection exists between 2. motor and control, there is a problem with motor or control board, 3. or motor amp draw is excessive. Control board status light blinks 5 times repeatedly Remove pump and try to run sprayer. If motor runs, check for locked or frozen pump or drive train. If sprayer does not run, continue to step 2. Set sprayer to OFF and disconnect power to sprayer. Disconnect motor connector(s) from control board socket(s). Check that motor connector and control board contacts are clean and secure. If contacts are clean and secure, continue to step 4. 4. Set sprayer to OFF and spin motor fan 1/2 turn. Restart sprayer. If sprayer runs, replace control board. If sprayer does not run, continue to step 5. 5. Perform Spin Test: Test at large 4-pin motor field connector. Disconnect fluid pump from sprayer. Test motor by placing a jumper across pins 1 & 2. Rotate motor fan at about 2 revolutions per second. A cogging resistance to motion should be felt at the fan. The motor should be replaced if no resistance is felt. Repeat for pin combinations 1 & 3 and 2 & 3. Pin 4 (the green wire) is not used in this test. If all spin test is positive, continue to step 6. Green Blue Red Black STEP 1: Green Blue Red Black STEP 2: Green Blue Red Black STEP 3: 311365G 15 Troubleshooting TYPE OF PROBLEM Sprayer does not run at all Digital display shows E=05 Control board status light blinks 5 times repeatedly WHAT TO CHECK Control is commanding motor to run 6. but motor shaft does not rotate. Possibly locked rotor condition, an open connection exists between motor and control, there is a problem with motor or control board, or 7. motor amp draw is excessive. HOW TO CHECK Perform Field Short Test: Test at large 4-pin motor field connector. There should not be continuity from pin 4, the ground wire, and any of the remaining 3 pins. If motor field connector tests fail, replace motor. Check Motor Thermal Switch: Unplug thermal wires. Set meter to ohms. Meter should read the proper resistance for each model (see table below). 100k ohm - ti13140a Resistance Table: 16 695 0 ohms 795 2k ohms 1095 3.9k ohms MARK V 3.9k ohms 311365G Troubleshooting TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK Sprayer does not run at all Allow sprayer to cool. If sprayer runs NOTE: Motor must be cooled down for the test. when cool, correct cause of 1. Check thermal device connector (yellow wires) overheating. Keep sprayer in cooler at control board. location with good ventilation. Make sure motor air intake is not blocked. 2. Disconnect thermal device connector from control If sprayer still does not run, follow board socket. Make sure contacts are clean and secure. Control board status light blinks Step 1. 6 times repeatedly 3. Measure resistance of the thermal device. If reading is not correct, replace motor. Digital display shows E=06 Check Motor Thermal Switch: Unplug thermal wires. Set meter to ohms. Meter should read the proper resistance for each model (see table below). 100k ohm - ti13140a Resistance Table: Sprayer does not run at all Digital display shows E=09 Control board status light blinks 9 times repeatedly Sprayer does not run at all Digital display shows E=10 Control board status light blinks 10 times repeatedly 311365G Check the connections. Control is not receiving a motor position sensor signal 695 0 ohms 795 2k ohms 1095 3.9k ohms MARK V 3.9k ohms 4. Reconnect thermal device connector to control board socket. Connect power, turn sprayer ON and control knob 1/2 turn clockwise. If sprayer does not run, replace control board. 1. Turn power OFF. 2. Disconnect motor position sensor and inspect for damage at connectors. 3. Reconnect sensor. 4. Turn power ON. If error continues, replace motor. Check to see if control board is over 1. heating. 2. Make sure motor air intake is not blocked. Make sure fan has not failed. 3. Make sure control board is properly connected to back plate and that conductive thermal paste is used on power components. 4. Replace control board. 5. Replace motor. 17 Troubleshooting Sprayer Will Not Shut Off 1. Relieve Pressure, page 9. Leave prime valve open and power switch OFF. 2. Remove control box cover so the control board status light can be viewed if available. Troubleshooting Procedure Plumb pressure gauge into paint hose, plug sprayer in, and turn power switch ON. Does sprayer reach or exceed its maximum pressure? NO Mechanical problem: See the proper fluid pump manual for the sprayer for further trouble shooting procedures. YES Unplug the transducer from control board. Does motor stop running? NO Replace the control board. YES Bad transducer. Replace and test with a new one. 18 311365G Troubleshooting Sprayer Will Not Run (See following page for steps) Remove control box cover. Turn sprayer ON. Observe control board status light on control board (see page 13). No light Once Normal operation Light on Control board Continuously commanding motor to run Flashing See Step 1. Do you have over 100 AC volts? NO See Step 2. Do you have over 100 AC volts? NO Repair or replace power cord. YES See Error Code section for further troubleshooting Replace the ON/OFF switch. YES See Step 3. Is the proper reading present through the thermal switch wires?. NO If motor is hot, let cool and retest. If Step 4 still shows incorrect resistance, replace motor. The motor has a defective thermal device. NO Connect a test transducer to the board. Does the motor run? YES See step 4. Does the motor run? NO YES YES Replace potentiometer. Pressure switch. 311365G Replace the control board. Replace the transducer 19 Pressure Control Board Pressure Control Board 100 - 120 Vac North American and Japan/Taiwan Motor Control Board Removal Installation 1. Apply small amount of thermal compound 15U114 or 110009 (5) to shaded component areas on rear of motor control board (52). Relieve pressure; page 9. Wait 5 minutes before servicing. 1. Remove four screws (38) and cover (96). 2. Disconnect display connector (A) from motor control board. 3. Remove bottom two screws (39) and allow control panel (68) to hang down freely. 4. Disconnect control board power lead(s) (D) from ON/OFF switch (33) and motor control board (52). 5. Disconnect potentiometer connector (C) from motor control board. 6. Disconnect WatchDog (49) switch connector (X) from motor control board. 7. Disconnect 15/20A switch (178) (1595 model only). 8. Disconnect transducer connector (E) from motor control board. 9. Disconnect motor connectors (F, G, and H) from motor control board. 10. Remove motor shroud. Disconnect and remove wiring from baffle. 11. Remove nut and screw (88) and disconnect ground wire (87). Disconnect coil connector (Y). Remove coil (81). 12. Remove top two screws (39) and control box (61). 13. Remove six screws (27), two screws (102) and control board. 14. Remove five screws (27), three screws (102) and motor control board. CAUTION To reduce risk of motor control board failure, do not overtighten screws (102) which can damage the electric components. 2. Install five screws (27), three screws (102) and motor control board. 3. Install motor control board (52) with five screws (27). Torque to 9-11 in-lb (1.02 - 1.24 N•m). Install and torque three screws (102) to values in illustration. 4. Connect motor connectors, (F, G and H) to motor control board. 5. Reconnect and install wiring in baffle. Install motor shroud. 6. Install control box (61) with top two screws (39). 7. Install coil (81) and tighten screw and nut (88). Tighten ground wire screw (87) and coil connector (Y). 8. Connect transducer connector (E) to motor control board. 9. Connect 15/20A switch (178) (1595 model only). 10. Connect motor control board power lead(s) (D) to ON/OFF switch (33). 11. Connect WatchDog (49) switch connector (X) to motor control board. 12. Connect potentiometer connector (C) to motor control board. 13. Install control panel (68) with two screws (39). 14. Connect display connector (A) to motor control board. 15. Install cover (96) with four screws (38). 20 311365G Pressure Control Board 100 - 120 Vac North American and Japan/Taiwan 81 88 5 87 Tighten 1 screw to 14-17 in-lb 52 26 Y 88 61 A 178 B F C A 52 E 40 96 38 33 D Tighten 2 screws to 11-14 in-lb E 39 86 20 49 82 C 67 82 34 115 X 68 39 49 Auto 1595 MARK V 311365G 21 Pressure Control Board 240 Vac Motor Control Board Removal Installation 1. Apply a small amount of thermal compound 15U114 or 110009 (5) to shaded areas on rear of motor control board (52). Relieve pressure; page 9. Wait 5 minutes before servicing. CAUTION 1. Remove all four screws (38) and cover (96). To reduce risk of motor control board failure, do not overtighten screws (102) which can damage the electric components. 2. Disconnect display connector (A) from motor control board (52). 3. Remove bottom two screws (39). disconnect potentiometer connector (C) from motor control board (52). Disconnect power cord connectors (D) and filter board connectors (J) from ON/OFF switch (33) and remove control panel (68). 2. Install six screws (27), two screws (102) and control board. 3. Install motor control board (52) with five screws (27). torque to 9-11 in-lb (1.02 - 1.24 N•m). Install and torque three screws (102) to values in illustration on page 23. 4. Disconnect WatchDog switch connector (X) from motor control board. 4. Connect motor connectors (F, G and H) to motor control board. 5. Disconnect motor control board power connectors (K) from filter board (146). 5. Reconnect wiring and install onto baffle. Install motor shroud. 6. Remove top two screws (39) and control box (61). 6. Connect transducer connector (E) to motor control board. 7. Disconnect transducer connector (E) from motor control board. 7. Connect motor control board power connectors (K) to filter board (146). 8. Disconnect motor connectors (F, G and H) from motor control board. 8. Install control box (61) with top two screws (39). 9. Remove motor shroud disconnect and remove wiring from baffle. 9. Connect filter board power connectors (J) and power cord connectors (D) to ON/OFF switch (33). 10. Remove five screws (27), three screws (102) and motor control board. 10. Connect potentiometer connector (C) to motor control board. 11. Remove six screws (27), two screws (102) and control board. 11. Connect WatchDog switch (X) to motor control board. 12. Install control panel (68) with two screws (39). 13. Connect display connector (A) to motor control board (52). 14. Install cover (96) with four screws (38). 22 311365G Pressure Control Board 240 Vac Filter Board Installation 1. Install filter board (146) with four screws (163). Relieve pressure; page 9. 2. Connect motor control board power connectors (K) to filter board (146). Removal 1. Remove four screws (38) and cover (96). 3. Connect filter board power connectors (J) to top two terminals of ON/OFF switch (33) and power cord connectors (D) to bottom two terminals of ON/OFF switch. 2. Disconnect display connector (A) from motor control board (52). 3. Remove bottom two screws (39). disconnect potentiometer connector (C) from motor control board (52). Disconnect power cord connectors (D) and filter board connectors (J) from ON/OFF switch (33) and remove control panel (68). 4. Connect potentiometer connector (C) to motor control board (52). 5. Connect WatchDog switch (X) to motor control board. 6. Install control panel (68) with two screws (39). 4. Disconnect WatchDog switch connector (X) from motor control board. 7. Connect display connector (A) to motor control board (52). 5. Disconnect motor control board power connectors (K) from filter board (146). 8. Install cover (96) with four screws (38). 6. Remove four screws (163) from filter board (146). 5 240 Vac 52 26 52 146 61 K A C 163 A 96 38 33 J A A E 39 E 39 C 82 68 80 20 67 82 34 115 X ti12995a 34 311365G 23 Pressure Control Board 110 Vac U.K. Motor Control Board Removal Relieve pressure; page 9. Relieve pressure; page 9. Wait 5 minutes before servicing. 1. Remove four screws (38) and cover (96). 2. Disconnect display connector (A) from motor control board. 3. Remove bottom two screws (39) and allow control panel (68) to hang down freely. 4. Disconnect control board power lead(s) (D) from ON/OFF switch (33) and motor control board (52). 5. Disconnect potentiometer connector (C) from motor control board. 6. Disconnect WatchDog (49) switch connector (X) from motor control board. 7. Disconnect 15/20A switch (178) (1595 model only). 8. Disconnect transducer connector (E) from motor control board. 9. Disconnect motor connectors (F, G, and H) from motor control board. 10. Remove motor shroud. Disconnect and remove wiring from baffle. 11. Remove nut and screw (88) and disconnect ground wire (87). Disconnect coil connector (Y). Remove coil (81). 12. Remove top two screws (39) and control box (61). 13. Remove six screws (27), two screws (102) and control board. 14. Remove five screws (27), three screws (102) and motor control board. 24 Installation 1. Apply small amount of thermal compound 15U114 or 110009 (5) to shaded component areas on rear of motor control board (52). CAUTION To reduce risk of motor control board failure, do not overtighten screws (102) which can damage the electric components. 2. Install five screws (27), three screws (102) and motor control board. 3. Install motor control board (52) with five screws (27). Torque to 9-11 in-lb (1.02 1.24 N•m). Install and torque three screws (102) to values in illustration. 4. Connect motor connectors, (F, G and H) to motor control board. 5. Reconnect and install wiring in baffle. Install motor shroud. 6. Install control box (61) with top two screws (39). 7. Install coil (81) and tighten screw and nut (88). Tighten ground wire screw (87) and coil connector (Y). 8. Connect transducer connector (E) to motor control board. 9. Connect 15/20A switch (178) (1595 model only). 10. Connect motor control board power lead(s) (D) to ON/OFF switch (33). 11. Connect WatchDog (49) switch connector (X) to motor control board. 12. Connect potentiometer connector (C) to motor control board. 13. Install control panel (68) with two screws (39). 14. Connect display connector (A) to motor control board. 15. Install cover (96) with four screws (38). 311365G Pressure Control Board 110 Vac U.K. Filter Board Removal Relieve pressure; page 9. Wait 5 minutes before servicing. 1. Remove four screws (38) and cover (96). 2. Disconnect display connector (A) from motor control board (52). 3. Remove bottom two screws (39). Disconnect potentiometer connector (C) from motor control board (52). Disconnect filter board connector (J) and power cord connector (D) from ON/OFF switch (33). Remove control panel (68). 4. Disconnect motor board control power connectors (K) from filter board (146). Disconnect filter connector (L) from power cord connector (L). 5. Remove four screws (163) from filter board (146). 311365G Installation 1. Connect motor control board power connectors (K) to filter board (146). Connect filter connector (L) to power cord connector (L). 2. Install filter board (146) with four screws (163). 3. Connect filter board power connector (J) and power cord connector (D) to ON/OFF switch (33). 4. Connect potentiometer connector (C) to motor control board (52). 5. Install control panel (68) with two screws (39). 6. Connect display connector (A) to motor control board (52). 7. Install cover (96) with four screws (38). 25 Pressure Control Board 110 Vac U.K. 5 Tighten 1 screw to 14-17 in-lb (1.58-1.92 N‚Ä¢ 52 146 163 26 102 61 A C 96 J 38 33 D 52 E A A 39 E 80 20 39 68 82 82 115 ti12996a 67 34 X 26 311365G Pressure Control Board Pressure Adjust Potentiometer Removal Installation Relieve pressure; page 9. Wait 5 minutes before servicing. 1. Remove four screws (38) and cover (96). 1. Install gasket (115), nut and potentiometer (82) on control panel (68). Torque nut to 30-35 in-lb (3.38 - 3.95 N•m). 68 82 82 115 96 ti13493a 38 2. Disconnect potentiometer connector (C) from motor control board (95). 95 ti12998a 2. Install pressure control knob (34): Check pressure control knob alignment to potentiometer shaft. Turn shaft fully clockwise and attach knob in full ON position with a hex wrench. 34 ti7258a C ti12997a 3. Remove pressure control knob (34) with a hex wrench. 34 3. Connect potentiometer connector (C) to motor control board. 95 ti7258a C ti12997a 4. Remove gasket (115), nut and potentiometer (82) from control panel (68). 68 4. Install cover (96) with four screws (38). 96 82 115 311365G 82 38 ti13493a ti12998a 27 Pressure Control Board Pressure Control Transducer 4. Remove four screws (39) and control box (61). Allow control panel (68) to hang down freely. Removal Relieve pressure; page 9. Wait 5 minutes before servicing. 1. Remove four screws (38) and cover (96). ti7458a 68 39 ti13494a 61 96 38 ti13493a 2. Disconnect transducer connector (E) from motor control board (95). 5. Remove grommet (40) from control box then remove transducer (86) and o-ring (20) from filter base (67). ti7260a 67 40 E 86 20 95 ti12999a 3. Disconnect potentiometer connector (C) from motor control board. ti13495a 6. Remove grommet (40) from transducer and save for reuse. 40 ti13495a ti12997a 28 C 311365G Pressure Control Board Installation 1. Install o-ring (20) and transducer (86) in filter base (67). Torque to 35-45 ft-lb (47-61 N•m). Install grommet onto transducer (86) and transducer into control box. 3. Install control box (61) and control panel (68) with four screws (39). ti7458a 40 67 ti7447a 39 61 ti13494a 68 86 20 4. Connect potentiometer connector (C) to motor control board. ti13496a 2. Connect transducer connector (E) to motor control board (95). C E ti12997a 95 5. Install cover (96) with four screws (38). ti12999a 96 38 311365G ti13493a 29 Drive and Bearing Housing Replacement Drive and Bearing Housing Replacement CAUTION Do not drop gear cluster (89) when removing drive housing (90). Gear cluster may stay engaged in motor front end bell or drive housing. Disassembly Assembly Make sure gear (89) and thrust washers (28, 30, 90a, 36; see page 29) are in place. Brush grease onto gear teeth. Relieve pressure; page 9. 1. Remove screw (31), two nuts (24), pail hanger (55) and pump rod cover (108). 1. Push drive housing (90) onto motor (84) and install with five screws (6). Torque to 190-210 in-lb (21-23 N•m). 2. Remove pump (91); see Displacement Pump Replacement, page 34 (695/795) page 36 (1095/1595/Mark V). 2. Install bearing housing (83) with four screws (14) and washers (12). Torque to 25-30 ft-lb (34-40 N•m). 3. Remove two screws (158) and shroud (72). 3. Install front cover (51) with four screws (31). 4. Remove four screws (31) and front cover (51). 4. Install shroud (72) with two screws (158). 5. Remove four screws (14) and washers (12) to remove bearing housing (83) and connecting rod (85). 5. Install pump (91); see Displacement Pump Replacement, page 34 (695/795) page 36 (1095/1595/Mark V). 6. Remove five screws (6) and pull drive housing (90) off motor (84). 6. Install pump rod cover (108) and pail hanger (55) with screw (31) and two nuts (24). 30 311365G Drive and Bearing Housing Replacement 72 158 84 51 90 6 31 85 12 14 83 24 31 108 55 91 ti13000a 311365G 31 Motor Replacement Motor Replacement Removal 11. Remove two screws (23) and nuts (19) on side opposite control. Relieve pressure; page 9. 1. Remove pump (91); see Displacement Pump Replacement, page 34 (695/795) page 36 (1095/1595/Mark V). CAUTION Do not drop gear cluster (89) when removing drive housing (90). Gear cluster may stay engaged in motor front end bell or drive housing. 2. Remove drive housing (90); see Drive Housing Replacement, page 30. 3. Remove shroud (58). 4. Remove four screws (38) and control cover (96). 5. Remove bottom two screws (39) and allow control panel (68) to hang down freely. 6. Disconnect all three motor connectors from motor control board (52). 7. Disconnect motor leads. 8. Remove top two screws (39) and control housing (61). 9. Remove strain relief (29) from motor wires and power bar plate (69). 10. Remove motor wires from baffle 278075 and remove baffle. 32 12. Loosen two nuts (19) on side near control and remove motor (84) from cart frame (62). Installation 1. Slide new motor (84) under two screws (23) in cart frame (62) near control. 2. Install two screws (23) and nuts (19) on motor side opposite control. 3. Install baffle and connect motor wires. 4. Tighten all four screws (23) and nuts (19). torque nuts to 115-135 in-lb (13-15 N•m). 5. Install strain relief (29) onto motor wires and into power bar plate (69). 6. Install control housing (61) with top two screws (39). 7. Connect motor leads. 8. Connect all three motor connectors to motor control board (52). 9. Install control panel (68) with two screws (39). 10. Install control cover (96) with four screws (38). 11. Install drive housing (90); see Drive Housing Replacement, page 30. 12. Install pump (91); see Displacement Pump Replacement, page 34 (695/795) page 36 (1095/1595/Mark V). 311365G Motor Replacement 158 62 58 84 36 61 19 90a 90 28 158 51 96 89 39 6 30 12 14 31 68 23 19 90 6 12 14 91 ti13001a 311365G 33 Displacement Pump Replacement for 695/795 Displacement Pump Replacement for 695/795 See pump manual 310643 or 310894 for pump repair instructions. Push up retaining ring (43) and push pump pin out. 44 See manual 311362, 311363, or 311364 for applicable sprayer part number references. ti7168a Removal 1. Flush pump. 43 Relieve pressure; page 9. 2. Remove screw (31) and slide pump rod shield (108) forward. 4. Remove suction tube (76), hose (94) and any washers and o-rings. 5. Loosen pump jam nut (56). Unscrew pump. 94 31 ti7167a ti7170a 108 3. Cycle pump in JOG mode until pump pin (44) is in position to be removed. Turn power switch OFF and unplug power cord. 34 56 76 311365G Displacement Pump Replacement for 695/795 Installation 2. Install pump pin (44). Verify retaining spring (43) is in groove of connecting rod (85). 3. Push pump up until pump threads engage. WARNING If pump pin works loose, parts could break off due to force of pumping action. Parts could project through the air and result in serious injury or property damage. CAUTION If the pump jam nut loosens during operation, the threads of the drive housing will be damaged. 1. Extend pump piston rod 1.5 in. Apply grease to top of pump rod at (A) or inside connecting rod. 4. Screw in pump until threads are flush with drive housing opening. Align pump outlet to back. 5. Install washers, o-rings and suction tube (76) and hose (94). 6. Screw jam nut (56) up onto pump until nut stops. Tighten jam nut by hand, then tap 1/8 to 1/4 turn with a 20 oz (maximum) hammer to approximately 75± 5 ft-lb (102 N•m). 7. Install pump rod shield (108) with screw (31). 8. Fill packing nut with Graco TSL until fluid flows onto top of seal. 1.5 in. A ti7169a ti7171a 311365G 35 Displacement Pump Replacement 1095/1595/Mark V Displacement Pump Replacement 1095/1595/Mark V Removal 7. Ratchet open pump door. a. Ratchet pump door forward. 1. Flush pump. 2. Stop pump with piston rod in its lowest position. Read Skin Injection Hazard; page 5. ti6373a 3. Do Pressure Relief, page 9. b. Twist latch u-bolt out of pump door recess. 4. Separate drain hose from sprayer. ti7326a c. Place u-bolt on pump door outer edge. d. If pump door is stuck, do steps e, f, and 8, otherwise go to step 9. e. Twist latch u-bolt back from pump door outer edge. ti6374a 5. Disconnect paint hose from pump. ti6300a f. Place u-bolt on pump door protrusion. 6. Raise latch lock. Push latch open. ti6369a ti6375a ti6370a 36 311365G Displacement Pump Replacement 1095/1595/Mark V 8. Ratchet pump door forward. ti6377a Installation 1. Adjust piston rod with pin holder to pull out piston rod. Tap piston rod on hard surface to push in piston rod. 2. Push pump collar flush with bearing housing ledge to be able to close pump door. ti6325a 9. Open pump door. ti7331a ti5492a 3. Slide pump into connecting rod. Push pump pin until it is fully retained. Note: Pin will snap into position. ti6378a 10. Pull out pump pin and place in pin holder. ti7328a ti7327a 311365G 37 Displacement Pump Replacement 1095/1595/Mark V 4. Close pump door and rotate latch into position. Do not tighten latch. 6. Tighten latch and rotate latch lock into locked position. ti7329a ti6313a ti6204a TI6312a 7. Attach drain hose to sprayer. 5. Rotate pump to align with paint hose. Connect paint hose and hand tighten to 70 in-lb. ti6299a ti7330a 8. Fill pump with Graco TSL until fluid flows onto top of seal. ti5493a 38 311365G Wiring Diagram Wiring Diagram 695/795 Lo-Boy Series A; 695 Hi-Boy Series A - C; 795 Hi-Boy Series A, B; 1095/1595/Mark V Series A Motor ti7346a green/ground ON/OFF Switch Black + Digital Display Power Plug white Black green/ground Pressure Transducer 20A 15A Switch 1595/MARK V Potentiometer Watchdog 311365G 39 Wiring Diagram Wiring Diagram 695/795 Lo-Boy Series A; 695 Hi-Boy Series A - C; 795 Hi-Boy Series A, B; 1095/1595/Mark V Series A Digital Display Potentiometer Motor Pressure Transducer Black Watchdog 20A 15A 1595 Switch ti12980a green/ground ON/OFF Switch Black white Black + Power Plug green/ground 40 311365G Wiring Diagram Wiring Diagram UltraMax II: 695/795 Lo-Boy Series A; 695 Hi-Boy Series A - C; 795 Hi-Boy Series A, B; 1095/Mark V Series A (Models with only TWO large capacitors on control board) Motor ti7523a green/ground ON/OFF Switch Black + Digital Display Power Plug white green/ground Japan/Taiwan Models Pressure Transducer Potentiometer Watchdog Motor ti7347a Black green/ground Blue 175 Blue Brown Blue ON/OFF Switch UK Models Digital Display green/ground Black Pressure Transducer Brown + Watchdog Power Plug 311365G 41 Wiring Diagram Wiring Diagram UltraMax II: 695/795 Lo-Boy Series B; 695 Hi-Boy Series D; 795 Hi-Boy Series C, 1095/Mark V Series B (Models with SIX large capacitors on control board) Thermal Switch Digital Display Potentiometer Motor Pressure Transducer Black AutoClean Motor Leads Watchdog Motor Sensor Leads ti13484a green/ground ON/OFF Switch Black white Black + Power Plug green/ground Thermal Switch Japan/Taiwan Models Digital Display Potentiometer Motor Pressure Transducer Black AutoClean Motor Leads Watchdog Motor Sensor Leads Blue Black UK Models Blue ti13485a Brown Blue ON/OFF Switch Brown + green/ground 42 Power Plug 311365G Graco Standard Warranty Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. TO PLACE AN ORDER OR FOR SERVICE, contact your Graco distributor, or call 1-800-690-2894 to identify the nearest distributor. This manual contains: English Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 www.graco.com 12/2005 Rev. 4/2009 311365G 43
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Mode : UseOutlines XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : FrameMaker 8.0 Modify Date : 2009:04:23 11:16:33-05:00 Create Date : 2004:01:13 15:39:28Z Metadata Date : 2009:04:23 11:16:33-05:00 Format : application/pdf Title : 311365G Ultra Max II/Ultimate Mx II, Repair, English Creator : qumjj2 Document ID : uuid:7311eec0-4799-4b7a-9631-7b49d20c3603 Instance ID : uuid:58de8ee7-7b9f-44a2-8769-dee7c19fab20 Page Count : 43 Author : qumjj2EXIF Metadata provided by EXIF.tools