Graco 310643u 310643U, Displacement Pumps, Repair, English User Manual To The 03271a1f 58a8 4443 9755 3cdee2f0e3d9

User Manual: Graco 310643u to the manual

Open the PDF directly: View PDF .
Page Count: 18

Download
Open PDF In Browser	View PDF

Repair

Displacement Pump

310643U
EN

Use only genuine Graco replacement parts. Use of non-Graco replacement parts may void
warranty.
3300 psi (22.7 MPa, 227 bar) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual.
Be familiar with the controls and the proper usage
of the equipment. Save these instructions.
Model 248204, Series A
UltraMax II and Ultimate MX II 695/795
ASM Zip-Spray 2700 Plus, 3100 Plus
ASM AllPro Mach 8600 Plus and 11000 Plus
ASM H2700 Plus
Model 255968, Series A
ASM 3600G Plus
Model 248205, Series A
UltraMax II and Ultimate MX II 1095/1595
Model 249059, Series A
TexSpray Mark V
Model 249057, Series A
TexSpray Mark V
Model 277069, Series A
LineLazer IV 3900, R300
Model 277070, Series A
LineLazer IV5900
Model 253056, Series A
Mark IV
Model 257146, Series A
Ironman 300E and Ironman 500G
ti2311

Warnings

Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Parts - Pump 248204, 277069, 255968 . . . . . . . . . 14
Parts - Pump 248205, 249057, 249059, 277070,
257146 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts - Pump 253056 . . . . . . . . . . . . . . . . . . . . . . . 16
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 18

Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation
point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these
symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard
symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.
• Use equipment only for its intended purpose. Call your distributor for information.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.
• Comply with all applicable safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure and disconnect all power sources.
SKIN INJECTION HAZARD
High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that
injection occurs, get immediate surgical treatment.
• Do not aim the gun at, or spray any person or animal.
• Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with
any part of the body.
• Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.
• Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn
off the unit and follow the Pressure Relief Procedure for turning off the unit.
• Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.

2

310643U

Service

Service
Pressure Relief Procedure

Pump Repair Kits

Follow the Pressure Relief Procedure whenever
you see this symbol.

Pump

Repair Kit

248204, 255968

248212

253056

287825

248205, 249057, 249059, 248213
257146
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing
fluid and moving parts, follow the Pressure Relief
Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
1. Engage trigger lock.
2. Turn ON/OFF switch to OFF.

Tools Needed
•

Vise

•

12 in. adjustable, open-end wrench (2)

•

Hammer (20 oz maximum)

•

Small screwdriver

•

Throat Seal Liquid

•

Pick or long small screwdriver

3. Unplug power cord.
4. Disengage trigger lock. Hold metal part of gun
against grounded metal pail and trigger gun into pail
to relieve pressure.
5. Engage the trigger lock.
6. Open all fluid drain valves in the system, having a
waste container ready to catch drainage. Leave drain
valve(s) open until you are ready to spray again.
7. If you suspect the spray tip or hose is clogged or
that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen tip
guard retaining nut or hose end coupling to relieve
pressure gradually, then loosen completely. Clear
hose or tip obstruction.

Cleaning and Inspecting Parts
Clean and inspect parts. Pay particular attention to the
ball seats in the intake valve and piston, which must
have no nicks or wear, and to the inside of the sleeve
and the outside of the piston rod, which must not be
worn or scratched. Replace worn or damaged parts.

COMPONENT RUPTURE HAZARD
To reduce the risk of serious injury from pressurized
fluid, never use sharp or pointed tools to remove
sleeve. If the sleeve cannot be removed easily, return
the sleeve and cylinder to a Graco distributor for
removal.
NOTE: Remove and clean sleeve when repacking pump.

310643U

3

Service

Repair When Pump is Separated
From Sprayer
Disassembling the Pump
1. Remove packing nut (202) and o-ring (228).

4. Tap piston rod out of cylinder with a hammer or flip
over and tap piston rod out against a bench.

NOTE: Sleeve may come out
of cylinder with piston rod.

202
228

ti7571a

5. Remove piston rod from sleeve, or remove sleeve
from cylinder. Mark IV models: Remove sleeve
spacer (230) from sleeve.

ti7566a

2. Unscrew intake valve from cylinder.

ti7572a
ti7569a

3. Disassemble intake valve. Clean and inspect o-ring
(227). NOTE: A pick may be required to remove
o-ring.
233

215
214
212
227

ti7570e

213
ti23115a

4

310643U

Service

8. Remove throat packings and glands from cylinder.
Discard throat packings and glands.

COMPONENT RUPTURE HAZARD
To reduce the risk of serious injury from pressurized
fluid, do not clean or wipe the piston valve threads.
Cleaning the piston valve threads could destroy the
special sealing patch and cause the piston valve to
come loose during operation.
6. Unscrew piston valve from piston rod. Clean and
inspect parts. The piston has a special thread locking/sealing patch. Do not remove the patch. The
patch allows four disassembly/assembly procedures
before it is necessary to apply thread sealant to the
threads.

ti7576a

7. Remove packings and glands from piston rod.

Not
used on
248204,
253056,
255968

ti7573b

Assembling the Pump
1. Soak all leather packings in SAE 30W oil for 1 hour
minimum prior to assembly. Stack male gland (204)
on piston rod. Alternately stack UHMWPE (208) and
leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) (note orientation) and backup washer (229) on
piston valve (210). Threads are good for four
repackings. Use thread sealant on piston valve
threads after four repackings.
Not
used on
248204,
253056,
255968

210
229

Not
used on
248204,
253056,
255968

216

217
218

204 208

ti7574d

ti3940b

310643U

5

Service

2. Install ball (206) in piston rod. If thread sealant is
applied to piston valve threads, make sure that none
gets on ball.

4. Soak all leather packings in SAE 30W oil for one
hour minimum prior to assembly. Place male gland
(204) in cylinder. Alternately stack UHMWPE (203)
and leather packings (223) (note orientation). Place
female gland (224) in top of cylinder seat packings.

206

Not
used on
248204,
253056,
255968

224

203

223

204

ti7573f
ti7575a

3. Tighten piston valve to piston rod as specified:
Models
248204, 253056,
255968, 244069
248205, 249057,
249059, 277070,
257146

Torque

5. Install seal (201) into packing nut (202). Install
o-ring (228) onto packing nut. Loosely install packing nut into cylinder.

27 +/-3 ft-lb.(36.1 +/-4.1 N•m)

201

55 +/-3 ft-lb.(74.6 +/-4.1 N•m)

202
228

ti7581a

6. Grease piston packings.

ti7576a

ti7578c

NOTICE
Do not slide piston assembly into top of sleeve as this
may damage piston packing.

6

310643U

Service

7. Slide piston assembly into bottom of sleeve.

10. Mark IV models: Install o-ring (231) on sleeve
spacer (230) and install sleeve spacer on sleeve.

230

231
ti7577a

ti7340a
ti7340b

8. Grease top inch or two of piston rod that will go
through the cylinder throat packings.

11. Reassemble intake valve with new o-ring (227),
seat (212) and ball (214). Seat may be flipped over
and used on other side. Clean seat thoroughly.

215
214
212
227

ti7579a

9. Grease o-rings (221) and place on sleeve. Slide
sleeve/piston rod assembly into bottom of cylinder.
Replace o-ring (207) if desired.
NOTE: O-ring (207) is not required for safe pump
operation.

213
ti23115a

207
221

ti7582a

310643U

7

Service

12. Install intake valve on cylinder. If a wrench is used
torque as follows:
Models
248204, 253056,
255968, 277069
248205, 249057,
249059, 277070,
257146

Torque
67 +/- 5 ft-lb (90.8 +/-6.8 N•m)
80 +/- 5 ft-lb (108.5 +/-6.8 N•m)

14. Remove o-ring (228) when pump packings begin to
leak after extended use. Then tighten packing nut
down until leakage stops or lessens. This allows
approximately 100 gallons of additional operation
before a repacking is required.
202
228

ti7568a
ti7569a

13. Torque packing nut (202) down onto adjustment
spacer (228) 100 +/- 10 in-lb. (11.3 +/- 1.1 N•m)

8

310643U

Service

Repair When Pump is On
Sprayer

4. Push out pin (29).
29

1. Perform Pressure Relief Procedure, page 3.
2. Remove intake valve.

26

ti4258b
ti4258b

5. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.

215
214
212
227

ti4258c

3. Push up retaining spring (26).
213
ti23115a

6. Remove piston rod and sleeve.

26

ti4258a

ti7746a

310643U

9

Service

7. Invert piston rod and sleeve and pound on hard surface until piston rod comes out of sleeve.
Mark IV models: Remove sleeve spacer from sleeve.

11. Remove piston valve from piston rod with a wrench.

ti4258g
ti4258g

ti7572a

12. Remove pin and piston rod from cylinder.

8. Remove packing nut (202).

202
ti4258h

ti7726a

9. Invert piston rod and insert into cylinder to force out
throat packings.

13. Soak all leather packings in SAE 30W oil for 1 hour
minimum prior to assembly. Stack male gland (204).
Alternately stack UHMWPE (203) and leather (223)
packings (note orientation). Install female gland
(224). Install seal (201) and packing nut (202) and
o-ring (228).

224

203

Not used on
248204,
253056,
255968
201

223

228
202

ti4258e

204

10. Insert piston rod into cylinder with pin hole up and
piston valve down. Insert pin into piston rod and
crank shaft.
ti7573c

ti4258f

10

310643U

Service

14. Remove packings and glands from piston rod.
Not used on
248204,
253056,
255968

16. Install ball (206) in piston rod. NOTE: If thread sealant is applied to piston valve threads, make sure
none gets on ball. Install piston valve on piston rod.
Torque as follows:
Models
248204, 253056,
255968, 277069
248205, 249057,
249059, 277070,
257146

Torque
27 +/- 3 ft-lb (36.6 +/-4.1 N•m)
55 +/- 3 ft-lb (74.6 +/-4.1 N•m)

ti3939a

15. Soak all leather packings in SAE 30W oil for one hour
minimum prior to assembly. Stack male gland (219)
on piston rod. Alternately stack UHMWPE (208)and
leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) and backup washer (229) (note orientation) on
piston valve (210). The special sealing patch on piston valve threads is good for four repackings. Use
thread sealant on piston valve threads after four
repackings.

206

219
217

ti7575b

Not
used on
248204,
253056,
255968

216
229

ti7575b

17. Grease piston packings.

206

218

208

210

ti3941a

ti7578c

310643U

11

Service

NOTICE
Do not slide piston assembly into top of sleeve as this
may damage piston packing.
18. Slide piston assembly into bottom of sleeve. Make
sure V-packing and u-cup are not rolled over or
damaged. Mark IV models: Install o-ring (231) on
sleeve spacer (230). Install sleeve spacer on
sleeve.

21. Torque seal and packing nut (202) down onto throat
adjustment spacer (228) to 100 +/- 10 in-lb (11.3 +/1.1 N•m).
Remove o-ring when pump packings begin to leak
after extended use. Then tighten packing nut down
until leakage stops or reduces. This allows approximately 100 gallons of additional operation before a
repacking is required.

Mark IV

202

228

ti7726b

ti7341a

19. Grease top inch or two of piston rod that will go
through the cylinder throat packings.

ti7579a

20. Grease o-ring (221) and place on sleeve. Slide
sleeve/piston rod assembly into bottom of cylinder.
Replace o-ring (207) if desired. NOTE: O-ring (207)
is not required for safe pump operation.

22. Push up retaining spring (26) with screwdriver.

26

ti4258k

23. Push in pin (29). NOTE: Make sure retaining ring
falls into slot.
29

26
ti4258m

207
221

ti4258j

12

310643U

Service

24. Reassemble intake valve with new o-rings (227)
and (230), seat (212) and ball (214). Seat may be
flipped over and used on other side. Clean seat
thoroughly.

Pump Packings

222

215

201

214
202
228

212
227

224

203

223
Leather

204

205

V-Max™
UHWMPE,
blue

213
221
ti23115a

220

25. Install intake valve on cylinder. Torque as follows:
Models
248204, 253056,
255968, 277069
248205, 249057,
249059, 277070,
257146

Torque
70 +/- 5 ft-lb (94.9 +/-6.8 N•m)

206
207
219
218

208

Leather

217
216

210

80 +/- 5 ft-lb (108.5 +/-6.8 N•m)

229
221
215

214
213

212
227

230

Pump 248204

V-Max™
UHWMPE,
blue

ti7683d

ti4258n

310643U

13

Parts - Pump 248204, 277069, 255968

Parts - Pump 248204, 277069, 255968
Series A
Ref.
201
202
203*

Part
179810
193046
192692

204*
205

15C987

206*
207*
208*

243346
243346
105444
114054
192693

210
212†

239932
239922

213

15C785
195892
214*† 105445*
215
192624
216* 118503
217* 178969
218* 178939
219* 196880
220
248209
221* 108526
222
248206
223* 178940
224* 15C988
227*† 107079
228
192714
229* 15C997
230* 118494

Description
Qty.
SEAL, throat
1
NUT, packing
1
V-PACKING, throat, V-Max,
3
UHMWPE, blue
GLAND, male, throat,
1
CYLINDER, pump
Model 248204, 255968
1
Model 16X428
1
BALL, sst, 0.3125 in.
1
PACKING, o-ring
1
V-PACKING, piston, V-MAX,
3
UHMWPE, blue
VALVE, piston
1
KIT, seat, carbide (includes 214 and
1
227)
VALVE, intake (foot)
1
Model 248204, 255968
Model 277069
BALL, sst. 0.5000 in.
1
GUIDE, ball
1
WIPER, piston
1
GLAND, female, piston
1
V-PACKING, leather, piston
2
GLAND, male
1
SLEEVE, cylinder
1
O-RING, ptfe
2
ROD, piston
1
V-PACKING, leather, throat
2
GLAND, female
PACKING, o-ring
1
SPACER, throat, nut
1
WASHER, backup
1
O-RING, fluoroelastomer
1
(not used on Lo-Boy)

201
202

221

228
222
224

223
219

203
204
208

217
216
229
206
210

215
205

214

* These parts are also included in Repair Kit 248212, which
may be purchased separately.
† These parts are also included in Carbide Seat Kit 239922,
which may be purchased separately.

218

212
207

227
213

221

220
(Not an O-ring groove)

230
ti4255a

14

310643U

Parts - Pump 248205, 249057, 249059, 277070, 257146

Parts - Pump 248205, 249057, 249059, 277070, 257146
Series A
Ref.
201
202
203*

Part
183171
193032
193124

204*
205

15C989

206
207*
208*
210
212
213

214

215
216*
217*
218*
219*
220
221*
222

243347
196754
101947*
116327
156633
193125
240150
244199
244571
15C783
196753
195894
102972*†
111453
196967
193027
118504
183185
15E329
183178
248210
257031
107098

223*
224*
227*†
228
229*
230*

248207
249028
183175
15C990
108526
C20987
15C998
118494

231

117608

232

162485

Description
Qty.
PLUG
1
NUT, packing
1
V-PACKING, throat, V-Max,
4
UHMWPE, blue
GLAND, packing, male, throat
1
CYLINDER, pump
1
Model 248205, 277070
Model 249057, 249059, 257146
BALL, 0.375 in.
1
Model 248205, 249057, 277070, 257146
Model 249059, ceramic
PACKING, o-ring
1
4
V-PACKING, piston, V-MAX,
UHMWPE, blue
VALVE, piston
1
KIT, seat, carbide (includes 214, 227)
1
Model 248205, 249057, 277070, 257146
Model 249059
HOUSING, intake (foot)
1
Model 248205
Model 249059, 249057
Model 277070, 257146
BALL
1
Model 248205, 249057, 277070, 257146,
0.875 in.
Model 249059, ceramic, 0.750 in.
1
GUIDE, ball
1
Model 249059, 249057
Model 248205, 277070, 257146
1
WIPER, piston
1
GLAND, female, piston
1
V-PACKING, leather, piston
3
GLAND, packing, male
1
SLEEVE, cylinder
1
Model 248205, 249057, 249059, 277070
Model 257146
PACKING, o-ring
2
ROD, piston
Model 248205, 277070
1
Model 249059, 249057, 257146
1
V-PACKING, leather, throat
3
GLAND, female, throat
1
PACKING, o-ring
1
SPACER, nut
1
WASHER, backup
1
O-RING, fluoroelastomer (not used on
1
249057, 249059, 257146)
NIPPLE, straight
1
Model 249057, 249059 (not shown)
ADAPTER, 3/8 npt x 3/8 npsm
1
Model 249057, 249059, 257146 (not
1
shown)

201

221

202
222
228
224

219
208

203
223

218

217
204

216
229

222

206
210
231

205

232
215
214

207

212
227

221

220

(Not an O-ring groove)

213

230
ti23114a

* These parts are also included in Repair Kit 248213, which may be
purchased separately.
† These parts are also included in Carbide Seat Kit 244199, which
may be purchased separately.
 These parts are also included in Pump Repair Kit 249189, which
may be purchased separately.

310643U

15

Parts - Pump 253056

Parts - Pump 253056
Ref.
201*
202
203*

Part
179810
193046
192692

Description
SEAL, throat
NUT, packing
V-PACKING, throat, V-Max,
UHMWPE, blue
204* 15C987
GLAND, male, throat
205
287876
CYLINDER, pump
206*
BALL, check
105444* BALL, sst, 0.3125 in. (optional)
119259 BALL, ceramic, 0.3125 in. (standard)
207* 156593
PACKING, o-ring
208* 192693
V-PACKING, piston, V-MAX,
UHMWPE, blue
210
287877
VALVE, piston
212† ^ 197470
SEAT, carbide
213
287878
HOUSING, intake
214
BALL, check, inlet
102972*† BALL, sst, 0.875 in. (optional)
111453 ^ BALL, ceramic, 0.750 (standard)
215
196967
GUIDE, ball
216* 118503
WIPER, piston
217* 178969
GLAND, female, piston
218
178939
V-PACKING, leather, piston
219* 196880
GLAND, male
220
248209
SLEEVE, cylinder
221* 108526
O-RING, ptfe
222
249969
ROD, piston (Mark IV)
223* 178940
V-PACKING, leather, throat
224* 15C988
GLAND, female
227*† ^ 108526
PACKING, o-ring
228* 158776
SPACER, throat, nut
229* 15C997
WASHER, backup
230
15G494
SPACER, sleeve
231* 107098
O-RING

Qty.
1
1
3

201
202

1
1
1

228

1
3
1
1
1
1

221

222
224
223
219

203
1
1
1
2
1
1
2
1
2

204
208

217
216

1
1
1
1
1

* These parts are also included in Repair Kit with stainless steel
ball,287825, which may be purchased separately.
 These parts are also included in Repair Kit with ceramic ball,
24V063, which may be purchased separately.
† These parts are also included in Carbide Seat Kit with stainless
steel ball, 244199, which may be purchased separately.
^ These parts are also included in Carbide Seat Kit with ceramic ball,
24V071, which may be purchased separately.

218

229
206
210

215
205
214
207

212
227

221

213

220
(Not an O-ring groove)
230
231

16

310643U

Technical Data

Technical Data
U.S.
Maximum Working Pressure
Fluid Inlet Size
Fluid Outlet Size
248204, 255968, 277069
248205, 249057, 249059,
253056, 277070, 257146
Wetted Parts

310643U

3300 psi
1-5/16-12 un(m)

Metric
227 bar, 22.7 MPa
1-5/16-12 un(m)
1/4 npt(f)
3/8 npt(f)

stainless steel, PTFE, leather, nylon, zinc-plated carbon steel, tungsten
carbide, chrome plating, fluoroelastomer, acetal, polyethylene

17

Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 310643

Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised U, April 2015



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Format                          : application/pdf
Creator                         : Kristine Beese
Description                     : Displacement Pumps
Title                           : 310643U, Displacement Pumps, Repair, English
Subject                         : Displacement Pumps, 310643, MM 310643, 310643U, 310643EN, 310643EN-U, 248204, 255968, 248205, 249059, 249057, 277069, LineLazer IV, TexSpray Mark V, UltraMax II Ultimate MX II, ASM Zip Spray 2700 Plus, AllPro Mach 8600 Plus
Create Date                     : 2009:12:15 10:08:57Z
Modify Date                     : 2015:05:07 16:25:51-05:00
Creator Tool                    : FrameMaker 11.0
Metadata Date                   : 2015:05:07 16:25:51-05:00
Marked                          : True
Job Ref                         : Z090766
Keywords                        : "Displacement Pumps, 310643, MM 310643, 310643U, 310643EN, 310643EN-U" 248204, 255968, 248205, 249059, 249057, 277069, LineLazer IV, TexSpray Mark V, UltraMax II Ultimate MX II, ASM Zip Spray 2700 Plus, AllPro Mach 8600 Plus,
Producer                        : Acrobat Distiller 10.1.13 (Windows)
Copyright                       : yes
Web Statement                   : Displacement Pumps
Document ID                     : uuid:940e17b0-f1b9-4724-a816-295d96793bc0
Instance ID                     : uuid:abe9a447-35fa-44fc-8766-215ac9f5f6a7
Page Count                      : 18
Language                        : en
Author                          : Kristine Beese

EXIF Metadata provided by EXIF.tools