Graco GNET Transceiver Module User Manual FCC Users Manual

Download:
Mirror Download [FCC.gov]
Document ID	609195
Application ID	/g3chG/meuRer6h5EvkR9w==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.06kB (63287 bits)
Date Submitted	2005-12-06 00:00:00
Date Available	2005-12-06 00:00:00
Creation Date	2005-11-15 16:16:36
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2005-11-15 16:16:36
Document Title	Microsoft Word - FCC Users Manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	twhite

USER INSTALLATION MANUAL
Graco GNET
FHSS RF Transceiver Module
TABLE OF CONTENTS
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
SCOPE.......................................................................................................3
REVISION CONTROL ...............................................................................3
APPLICABLE DOCUMENTS .....................................................................3
DESCRIPTION...........................................................................................4
ELECTRICAL SPECIFICATIONS ..............................................................4
CONNECTOR PINOUT..............................................................................4
MOUNTING LOCATION ............................................................................5
ANTENNAS................................................................................................5
LABELING REQUIREMENTS....................................................................6
RF EXPOSURE .........................................................................................6
FCC NOTIFICATIONS ...............................................................................7
1.0 SCOPE
This manual covers the necessary items to install a Graco GNET FHSS RF
Transceiver Module into a piece of host equipment. Antenna considerations,
electrical specifications, and labeling requirements are addressed.
2.0 REVISION CONTROL
DATE
3/23/04
CHANGES
ORIGINAL RELEASE
3.0 APPLICABLE DOCUMENTS
248292 RF Board
248293 RF Daughter Board
REVISION
0.0
4.0 DESCRIPTION
The Graco GNET FHSS RF Transceiver Module is a frequency hopping
spread spectrum transceiver capable of 2-way transportation of message
packets in the 900 MHz ISM band. A standard serial interface operating at 3
volts CMOS levels is used to communicate with the host device. Exact
protocol and messaging details are available in the Graco GNET FHSS RF
Transceiver Module Host Interface Protocol document.
The host device supplies power through the interface connector in
accordance with the operating voltage and current requirements.
5.0 ELECTRICAL SPECIFICATIONS
The module should be operated within the electrical limits provided in this
section. Operation outside of these parameters may damage the unit.
Parameter
Operating Voltage
Transmit Current
Receive Current
Sleep Current
Operating Temperature
Min
8.6
Typ
9.6
150
15
N/A
-40
6.0 CONNECTOR PINOUT
J3-1
J3-2
J3-3
J3-4
J3-6
Power In (9.6 Volts typical)
Regulator Shutdown Control (Shutdown = 0 volts)
RX
TX
Gnd
Max
10.6
200
N/A
+85
Units
VDC
mA
mA
µA
°C
7.0 MOUNTING LOCATION
In order to maintain compliance with the FCC modular certification it is
necessary to mount the module in such a way that user is never closer than
20 cm to the antenna.
The manual for end users of the product must contain a warning about the
20 cm separation as outlined in Section 10.0.
Additionally, the transceiver may not be co-located with any other antenna or
transmitter.
8.0 ANTENNAS
Compliance with FCC regulations may only be maintained using the
specified antennas. The orientation of the antennas is controlled as a
requirement on the engineering documentation.
Re:
248292 RF Board
248293 RF Daughter Board
The specified wire antenna will be attached at the factory and should not be
altered.
9.0 LABELING REQUIREMENTS
The FCC requires that the Part 15 statement be installed on the outside of
the final product in a manner which allows it to be seen and read. The
accepted statement and a sample label format are as follows:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1.
This device may not cause harmful
interference, and
2.
This device must accept any
interference received, including
interference that may cause undesired
operation.
Contains
FCC ID: JHIGNET
IC:
4840A-GNET
MODEL: XXXXXX
Graco Inc.
P.O. Box 1441
Minneapolis, MN
55440, U.S.A.
The label should be printed or molded into the case using a type front and
size that is readable with the unaided eye. The FCC identification number is
required.
10.0
RF EXPOSURE
This module has been designed to comply with FCC RF exposure
requirements outlined in Parts 2.1091, 2.1093, and 15.247(b)(4). Deviation
from the recommended installation may violate RF exposure requirements.
The Graco GNET RF Transceiver Module is limited in application to products
“generally used in such a way that a separation distance of at least 20
centimeters is normally maintained between the transmitter’s radiating
structure(s) and the body of the user and nearby persons.”
11.0
FCC NOTIFICATIONS
The Graco GNET FHSS RF Transceiver Module generates radio frequency
energy. It must be installed according to the manufacturer’s guidelines or it
has the potential to cause interference with other radio devices. Testing has
been performed to assure that it conforms to the FCC Part 15 rules for
intentional and unintentional radiators.
No further EMI compliance testing of the transmitter is required as long as
the 20 cm separation and co-location requirements are observed. Each new
use of the module will, however, always need to be scanned for unintentional
radiation from digital clocks, etc.
All necessary calibration has been performed at the time of manufacture.
Any modification of the device after it leaves the factory is a violation of FCC
rules.
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including
interference that may cause undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
RF Exposure (OET Bulletin 65)
To comply with FCC RF exposure requirements for mobile transmitting
devices, this transmitter should only be used or installed at locations
where there is at least 20cm separation distance between the antenna
and all persons.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2005:11:15 16:16:36-06:00
Create Date                     : 2005:11:15 16:16:36-06:00
Format                          : application/pdf
Title                           : Microsoft Word - FCC Users Manual.doc
Creator                         : twhite
Document ID                     : uuid:a364d975-2954-4c7e-9099-e21017e7c82e
Instance ID                     : uuid:6becaed7-1894-4056-9d76-77a04c91a425
Page Count                      : 7
Author                          : twhite

EXIF Metadata provided by EXIF.tools