Graco 308048K Quiet Viscount Ii Hydraulic Motor Users Manual 308048K, Motor, Instructions Parts Manual, English

223646 to the manual 100abc41-701d-4c99-a6c4-457aca5e23b1

2015-04-02

: Graco Graco-308048K-Quiet-Viscount-Ii-Hydraulic-Motor-Users-Manual-686053 graco-308048k-quiet-viscount-ii-hydraulic-motor-users-manual-686053 graco pdf

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

Instructions–Parts List

Quiet ViscountR II
Hydraulic Motor

308048K
ENG

Used as hydraulic drive for reciprocating pumps.
For professional use only.
Model 223646, Series B
1500 psi (10 MPa, 103 bar) Maximum Hydraulic Fluid Input Pressure
Patent No. 4,792,291
Foreign Patents Pending

Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.

Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . 14
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Graco Phone Number . . . . . . . . . . . . . . . . . . . . 16

04471

Symbols
Warning Symbol

Notice Symbol

NOTICE

WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.

WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS

This equipment is for professional use only.
Read all instruction manuals, tags, and labels before operating the equipment.
Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
Check equipment daily. Repair or replace worn or damaged parts immediately.
Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.
Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
Handle hoses carefully. Do not pull on hoses to move equipment.
Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82C (180F) or below –40C (–40F).
Do not move or lift pressurized equipment.
Wear hearing protection when operating this equipment.
Comply with all applicable local, state, and national fire, electrical, and safety regulations.

308048

WARNING
SKIN INJECTION HAZARD
Spray from the gun, hose leaks or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin
can also cause serious injury.
Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgical treatment.
Do not point the gun at anyone or at any part of the body.
Do not put your hand or fingers over the spray tip.
Do not stop or deflect leaks with your hand, body, glove or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the gun when spraying.
Check the gun diffuser operation weekly. Refer to the gun manual.
Be sure the gun trigger safety operates before spraying.
Lock the gun trigger safety when you stop spraying.
Follow the Pressure Relief Procedure on page 7 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
Tighten all fluid connections before operating the equipment.
Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.
Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.

MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the Pressure Relief Procedure on page 7 to prevent the
equipment from starting unexpectedly.

308048

WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
Ground the equipment and the object being sprayed. Refer to Grounding on page 6.
If there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately. Do not use the equipment until you identify and correct the problem.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
Keep the spray area free of debris, including solvent, rags, and gasoline.
Before operating this equipment, electrically disconnect all equipment in the spray area.
Before operating this equipment, extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or off any light switch in the spray area while spraying or while there are any fumes
in the air.
Do not operate a gasoline engine in the spray area.

TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.

308048

Installation
NOTICE

WARNING
The maximum safe hydraulic input pressure to this
motor depends on the pressure rating of the displacement pump to which it is connected.

Recommended Hydraulic Oil
Use Graco-approved Hydraulic Oil, Part No. 169236
(5 gal) or 207428 (1 gal)) or a premium, ISO grade
46 petroleum-based hydraulic oil containing rust and
oxidation inhibitors and anti-wear agents.

Refer to the lower manual and the pump manual
for the maximum fluid working pressure and the
ratio. Never exceed the maximum fluid working
pressure of the pump. Serious injury or damage to
the equipment may result.

Before using any other type of oil in this motor,
contact your Graco distributor. Unauthorized use of
lesser grade oil or substitutes may void the warranty.

Maximum Hydraulic Input Pressure

WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 7.
Be sure you always shut off the supply line shutoff
valve (E) first, and then the return line shutoff
valve. This is to prevent overpressurizing the motor
or its seals. When starting up the hydraulic system,
open the return line shutoff valve first.

NOTICE

Hydraulic Oil Working Temperature
The recommended hydraulic oil operating temperature is 80–115F (27–45C). The motor seals will
wear faster and leakage may occur if the pump is
operated at higher oil temperatures.
If the hydraulic oil temperature approaches 130F
(54C), check the hydraulic fluid supply cooling
system, filters, etc. and clean or repair as needed.
Refer to the complete pump manual for detailed installation information or contact your Graco distributor.
NOTE: A 1 in. npt seal (7) is supplied in a plastic bag
with the motor. Thread the seal onto the threads of
your hydraulic return line fitting (A). Thread the fitting
into the upper housing (53) and torque as needed.
Then tighten the seal (7) against the motor to provide a
secure seal. See Fig. 1.

Keep the hydraulic system clean
To reduce the risk of damaging the hydraulic power
supply, blow out all hydraulic lines with air, flush
thoroughly with solvent, and then blow out with air
again before connecting the lines to the motor.

53
A

Always plug the hydraulic inlets, outlets and lines
when disconnecting them to avoid introducing dirt
and other contaminants into the system.
Carefully follow the manufacturer’s recommendations
on reservoir and filter cleaning, and periodic changes
of hydraulic fluid.

Fig. 1

04467

308048

Installation
4. Spray gun: obtain grounding through connection to
a properly grounded fluid hose and pump.

Grounding

WARNING
For your safety, read the FIRE AND EXPLOSION
HAZARD WARNINGS on page 4, and ground
your entire system as instructed below. This section also includes details on how to connect the
grounding wire and clamp to the various hydraulic
motors.
Proper grounding is an essential part of maintaining a
safe system.
To reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment. Be
sure to ground all of this equipment:

5. Fluid supply container: according to local code.
6. Object being sprayed: according to local code.
7. Any pails used when flushing: Use only metal,
grounded pails when flushing. Make firm metal-tometal contact between the metal part of the spray
gun and the pail. Use the lowest possible pressure.
8. To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
gun firmly to the side of a grounded metal pail, and
then trigger the spray gun.

1. Pump: use a ground wire and clamp as shown to
the right. Loosen the locknut (A) of the grounding
lug and washer. Insert one end of the wire (B) in
the grounding lug (14) and tighten the locknut
securely. See Fig. 2. Connect the other end of the
wire to a true earth ground, as recommended by
your local code. Order Part No. 237569, Ground
Wire and Clamp.

2. Hydraulic hoses and fluid outlet hoses: use only
electrically conductive hoses.
A
3. Hydraulic power supply and air compressor:
follow manufacturer’s recommendations.

308048

Fig. 2

14
04468

Service
Pressure Relief Procedure

WARNING
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:

are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray tip.

Before you start:
Be sure you have all necessary parts on hand.
1. Repair Kit 223654 is available. The kit must be
purchased separately. An asterisk behind a reference number in the parts list, for example (21*),
indicates that the part is included in the repair kit.
2. Clean all parts as you disassemble them and
inspect them for wear or damage. Replace parts
as necessary. Use Loctite TL–242 thread
sealant, or the equivalent, when thread sealant is
specified.

Disassembly (Refer to Fig. 3)
NOTE: Use all the replacement parts that are in the
repair kit.

1. Lock the gun trigger safety.
2. Shut off the hydraulic power supply.
3. Close the supply line shutoff valve, and then the
return line shutoff valve.
4. Unlock the gun trigger safety.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.

1. Flush the displacement pump if possible.

WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 7.
2. Relieve the pressure.

6. Lock the gun trigger safety.
3. Stop the pump at the bottom of its stroke.
7. Open the drain valve (required in your system),
having a container ready to catch the drainage.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the obstruction.

NOTICE
Avoid getting dust or dirt in the motor during service.
Cleanliness is essential when repairing an hydraulic
motor.
4. Disconnect the displacement pump hoses. Disconnect the hydraulic hoses and plug all hydraulic
connections and lines to prevent contamination.

308048

Service
Disassembly (continued – refer to Fig. 3)

NOTICE
When removing the displacement pump, hold it
securely. The pump is heavy and could fall off the
motor.
5. Disconnect the displacement pump from the
motor, as explained in your separate pump manual.
6. Place the hydraulic motor in a bench vise.
7. Push or lightly tap the piston (30) up as far as
possible.
NOTE: The tie rod nuts (19), socket screws (51), cap
screws (36), and retainer (34) are fastened with Loctite TL–242. Heat may be used sparingly to soften
adhesive sealant during disassembly.
8. Remove the cap screws (12), the drip pan (16),
the drip cover (18), and machine screw (20) before
loosening the tie rod nuts. Then remove the four
tie rod nuts (19). Loosen the nuts (B) on the hydraulic tube (4) and loosen the tie rods (57).

13. Unscrew the top and bottom compression nuts (B)
on the hydraulic tube (4). Rotate the upper housing
(53) and remove the tube, being careful not to
damage the flare (A). Allow the oil to drain from
the motor into the pan.
NOTE: With the tie rods removed, the assembly may
separate at the joints between the cylinder (29) and
the upper and lower housings (53 and 25).
14. Rock the upper housing (53) to work it free and lift
it about 3 inches off the cylinder (29). The cylinder can stay in the lower housing (25).
15. Hold the trip rod (31) with an adjustable wrench on
the flats of the rod, and remove the top hex nut
(46) from the trip rod.
16. Remove the upper housing (53).
17. Remove the trip rod guides (37), compression
springs (45) and valve spool (38) from the upper
housing. Inspect the bearing inside of the guide
(35) in place. If bearing is damaged replace item
35.

9. Remove the motor from the vise and lay it in a
pan.

NOTE: Inspect the trip rod (31) above the shoulder for
damage. There must be no reduction in diameter.
Replace if necessary.

10. Remove one detent assembly: retaining plug (39),
o-ring (41), spring (40), ball guide (42) and ball
(43). If the ball or other parts stick in the upper
housing (53), turn the motor over and tap lightly.
Do not allow the parts to fall into the motor. Repeat
the procedure for the other detent assembly.

18. Pull the trip rod and piston from the lower housing
(25) and cylinder (29). Place the piston flats (30) in
a vise; tighten the vise on the flats of the piston.
Use a face spanner to remove the retainer (34).
Remove the trip rod (31) from the piston (30).

11. Remove the tie rods (57), but do not remove the
crown nuts (44).

19. Remove the trip rod locknut (27) and piston stop
(28). If the piston is replaced, remove the spring
(26) to use in the new piston.

12. Remove the socket screws (51) and the end cap
(47). Pull the stop plug (48) from the upper housing (53).

308048

20. Remove the bearing (23), packings (24), and
o-ring (21).

Service
50
51
47
48
44
52

*49
55a
55

33*

54
54a

43 42

B
56

29
33*

40*
41
39

24*
54

7
58

54a

46
6a

45*
4

A
31

23*

38
*45

24*

21*

*32
26

14
15

19
30

18
13

16
*17

NOTE: Circled letters refer to connected points.
04466

Fig. 3

308048

Service
Reassembly (Refer to Fig. 4)
1. Install the bearing (23*) in the lower housing (25).
Lubricate the seals (24*) with hydraulic oil. Install
them in the lower housing (25) with the lips facing
up toward the top of the motor.
2. Install the o-ring (21*) onto the lower housing (25).
3. Place the piston flats in a vise. Install the spring
(26) inside the piston (30). The compression rings
(32*) must be positioned with the joints about 180
opposed. Be sure the o-ring (17*) is in place.
4. Install the piston stop (28) and locknut (27) on the
trip rod. Torque the nut to 117–123 in-lb (13.2–13.9
N.m). Slide the trip rod (31) into the piston (30).
Apply thread sealant to the retainer (34) threads.
With the piston flats in a vise, tighten the retainer
until it is flush or below the piston surface. This is
important to prevent the retainer from backing out
during operation and damaging the motor.

10. Remove the adjustable wrench. Seat the upper
housing (53) onto the cylinder (29), so the tube
fittings align with those on the lower housing (25).
Reinstall the hydraulic tube (4) and loosely tighten
the compression nuts.
11. Replace the o-ring (49*) on the stop plug (48).
Seat the plug into the upper housing (53).
12. Install the end cap (47), using thread sealant on
the socket screws (51).
13. Lubricate the threads of the tie rods (57) and install
them with lockwashers (52). If the crown nuts (44)
were removed, reinstall them and torque them
onto the rods to 70–80 ft-lb (95–108 N.m).
14. Torque tie rods into base, apply thread sealant to
tie rod threads, then torque the tie rod nuts (19) to
70–80 ft–lb (95–108 N.m).

NOTE: Set base (2) on workbench during reassembly.
5. Install the o-ring (33*) onto the cylinder (29). Install
the cylinder (29) into the lower housing (25).
6. Install the trip rod and piston into the cylinder (29)
and lower housing (25) so the piston is recessed at
least 1 inch (25 mm) from the top of the cylinder.
7. If the bearing and guide (35) was removed, install
it on the upper housing (53) with the three screws
(36) (apply thread sealant).
8. Hold the flats of the trip rod with an adjustable
wrench and install the upper housing (53). The trip
rod will protrude from the top.
9. Slide the lower trip rod guide (37) and spring (45)
onto the trip rod. Install the spool (38) with the
detent at the top. Install the top spring (45) and
guide (37) on the trip rod. Install the top hex nut
(46). Torque the nut to 82–88 in-lb (9.3–9.9 N.m).

308048

15. With the motor on its side, install one detent
assembly: the ball (43), guide (42) with the concave surface toward the ball, spring (40*), o-ring
(41) and retaining plug (39). Torque the plug to
145–160 in-lb (16–18 N.m). Repeat for the other
side of the motor.
16. Slide the drip cover (18) onto the piston (30) up to
the o-ring (17). Install screw (20) into the piston.
Attach the drip pan (16) to the base using screws
(12).
17. Snugly tighten the compression nuts on the hydraulic tube (4) and torque to 60–80 ft-lb (81–108
N.m).
18. Install the motor on the displacement pump. Reconnect all fluid lines. Be sure the ground wire is
connected before operating the pump.

Service
50
51
47
48
44
52

*49
55a
55

54
54a

43 42

B
56
40*
41
39

24*

54a

46
6a

45*
4

A
31

23*

*45
6

33*

3
5

24*

35
5

21*

*32
26

14
15

Rings must be positioned with joints opposed

Lips must face up toward top of motor

Lubricate threads

Torque to 70–80 ft-lb (95–108 N.m)

Apply thread sealant

Torque to 60–80 ft-lb (81–108 N.m)

Torque to 117–123 in-lb (13.2–13.9 N.m)

19
30

Torque to 82–88 in-lb (9.3–9.9 N.m)

Torque to 145–160 in-lb (16–18 N.m)

18
13

16
*17

04466

Fig. 4

308048

Parts
Model 223646, Series B
50
51
47
48
44
52

*49
55a
55

33*

54
54a

43 42

B
56

29
33*

40*
41
39

24*
54

7
58

54a

46
6a

37
45*

6
4

A
31

23*

38
*45

24*

28
21*

*32
26

14
15
9
11
19

18
13

16
*17

NOTE: See the service section for important
torque and lubrication information.
NOTE: Circled letters refer to connected points.
04466

308048

Parts
Model 223646, Series B
Ref.
No.

Part No.

Description

1
2
3

290331
186221
110797

LABEL, instruction, English
BASE
ELBOW, male, 3/4 npt

1
1

Includes item 3a

3a
4
5

110926
210108
112574

1
1
1

110791

6a
7

110926
110876

7a
8
9
10

110927
183695
172975
100508

11
12

172815
100333

.O-RING, nitrile rubber
TUBE
ADAPTER, 3/4 npt (f) x
1–1/16–12
TEE, 7/8–14 unf–2a x 1 1/16–
12un–2a, 37 flare for 3/4 in. dia.
tube, Includes item 6a
.O-RING, nitrile rubber
ADAPTER, 1 –11-1/2 npt x
1 5/16–12un–2a, Includes item 7a
.O-RING, nitrile rubber
LABEL, identification not shown
LABEL, warning
SCREW, type “u” drive,
No. 4 x 0.188 in.
PLATE, warning
SCREW, cap, hex hd;
1/4–20 x .0.5 in.
ADAPTER, barbed hose, 1/8
npt x 0.25 in. (6.4 mm) ID hose
GROUNDING LUG
WASHER
PAN, drip
O-RING, nitrile rubber
COVER, drip
NUT, hex jam, 5/8–18
SCREW, machine, hex hd;
No. 10–20 x 0.375 in.
O-RING, buna–N
BEARING, piston,
bronze-filled PTFE
SEAL, u-cup, polyurethane
HOUSING, lower
SPRING, compression
NUT, hex, self-locking, 5/16–18
STOP, piston
CYLINDER
PISTON
ROD, trip
RING, piston, compression

103875

14
15
16
17*
18
19
20

104029
104582
210110
165295
171397
100155
101577

21*
23*

110800
186223

24*
25
26
27
28
29
30
31
32*

110795
186218
104664
103450
181243
186219
188087
171407
104103

Qty.

1
1
1
1
1
4
1
3
1
1
1
1
1
1
4
1
1
1
2
1
1
1
1
1
1
1
2

Ref.
No.

Part No.

Description

33*
34
35
36

166071
171398
210292
108538

37
38
39
40*
41
42
43
44
45*
46
47
48
49*
50
51

183659
183658
186222
108522
110801
167210
101701
104143
171411
104105
180953
171416
104093
108132
101864

52
53
54

100128
186217
110792

54a
55

110801
110799

O-RING, nitrile rubber
RETAINER
BEARING and GUIDE
SCREW, soc flat hd, self locking,
1/4–20 x 1/2 in.
GUIDE, trip rod
SPOOL, valve
RETAINER, spring
SPRING, helical compression
O-RING, nitrile rubber
GUIDE, ball
BALL, 1/4 in. dia.
NUT, crown, 5/8–18
SPRING, compression
NUT, hex lock, 1/4–20
CAP, end
PLUG, stop
O-RING, nitrile rubber
RING, lift
CAPSCREW, soc hd,
5/16–18 x 1 in.
LOCKWASHER, spring, 5/8 in.
HOUSING, upper
ELBOW, 90, 7/16–20 unf–2a(m)
x 9/16–18 unf–2a(m), 37flare for
3/8 in. dia. tube, Includes item 54a
.O-RING, nitrile rubber
PLUG, 9/16–18 unf–2b,

55a
56
57
58

110925
223608
171405
105430

Qty.

Includes item 55a

.O-RING, nitrile rubber
TUBE, drain
ROD, tie
NUT, seal, 1 in. npt
supplied in a plastic bag

2
1
1
3
2
1
2
2
2
2
2
4
2
1
1
1
1
1
3
4
1

2
2
1
1
1
4
1

These parts are also included in Repair Kit 223654,
which may be purchased separately.

Replacement Danger and Warning labels, tags and
cards are available at no cost. Label 290331 is also
available in the following languages:
German (Part No. 290396)
French (Part No. 290397)
Spanish (Part No. 290398).

308048

Mounting Hole
Layout

Dimensions
1

5
6
2

1
2

02589

Four 0.437 in. (11.1 mm) dia. mounting holes

3.712 in. (9.45 cm)

3.464 in. (8.79 cm)

4.0 in. (9.84 cm)

1 in. npt Outlet

2.0 in. (5.08 cm)

3/4 in. npt Inlet

Three 5/8–11 UNC (2B) tapped holes

11.25 in. dia. (285.8 mm)

Gasket 161806 is not shown. Order Separately

24.94 in. (633.8 mm)

1.8 in. to top of 4.69 in. stroke

308048

5
02631

Technical Data
Category

Data

Maximum hydraulic fluid input pressure

1500 psi (10 MPa, 103 bar). Also see the WARNING on
page 5.

Maximum hydraulic fluid flow

12 gpm (45.6 liter/min)

Hydraulic fluid consumption

1 gal. (3.8 liter) per 5 cycles

Effective piston area

4.9 sq. in. (31.6 cm2)

Piston rod diameter

2.5 in. (64 mm)

Stroke length

4.69 in. (119.1 mm)

Thrust at 1500 psi (10 MPa, 103 bar)

7300 psi (32 472 N)

Weight

approx. 96 lb. (43.5 kg)

Loctite is a registered trademark of the Loctite Corp.
Sound Data
Hydraulic Pressure
1500 psi (10 MPa, 103 bar)

dB(A) at 20 cycles
per minute

dB(A) at 30 cycles
per minute

dB(A) at 60 cycles
per minute

308048

Graco Warranty and Limitation of Liability
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308048
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

308048

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Keywords                        : Viscount II, Hydraulic Motor, 308048, Z058699, 223646
Modify Date                     : 2013:10:02 08:52-05:00
Create Date                     : 2010:08:12 09:53:23-05:00
Metadata Date                   : 2013:10:02 08:52-05:00
Format                          : application/pdf
Title                           : 308048K, Quiet Viscount II Hydraulic Motor, Instructions-Parts Manual, English
Description                     : Viscount II Hydraulic Motor
Creator                         : Bill Jorgenson
Subject                         : Viscount II, Hydraulic Motor, 308048, Z058699, 223646
Document ID                     : uuid:556f0577-bf1e-4e65-bfda-87a2998a0504
Instance ID                     : uuid:7f5a6838-f74e-48d7-a59c-b5e566c15ee9
Page Count                      : 16
Author                          : Bill Jorgenson

EXIF Metadata provided by EXIF.tools

Graco 308048K Quiet Viscount Ii Hydraulic Motor Users Manual 308048K, Motor, Instructions Parts Manual, English

223646 to the manual 100abc41-701d-4c99-a6c4-457aca5e23b1

Navigation menu

Versions of this User Manual:

Views

Navigation