Graco 311777F Texture Guns Users Manual 311777F, Guns, Repair, US English

245924 311777EN-F

288629 to the manual 899943b7-dddb-4c23-8b6a-864e89316f97

: Graco Graco-311777F-Texture-Guns-Users-Manual-686553 graco-311777f-texture-guns-users-manual-686553 graco pdf

Open the PDF directly: View PDF .
Page Count: 4

Download
Open PDF In Browser	View PDF

Texture Guns
Models: 288628, 288629, and 245924

English

125 psi (8.75 bar, 0.875 MPa) Maximum Air Working Pressure
70 psi (4.9 bar, 0.49 MPa) Maximum Fluid Working Pressure
IMPORTANT SAFETY INSTRUCTIONS. Refer to your
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Keep these instructions.

311777F
Model
288628,
no hopper
Model
245924,
with hopper

Model
288629
ti8808a

ti8508a

- For Water-Based Materials Only The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point
symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.
Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNINGS
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured
components can splash in the eyes or on skin and
cause serious injury.
• Follow Pressure Relief Procedure in this manual when
you stop spraying and before cleaning, checking, or
servicing equipment.
• Tighten all fluid connections before operating the
equipment.
• Check hoses, tubes, and couplings daily. Replace worn
or damaged parts immediately.

FIRE AND EXPLOSION HAZARD

Repair

Flammable fumes, such as solvent and paint fumes,
in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths
(potential static arc).
• Keep work area free of debris, including solvent, rags
and gasoline.
• Do not plug or unplug power cords, or turn power or light
switches on or off when flammable fumes are present.
• Ground all equipment in the work area. See Grounding
instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering
into pail.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you
identify and correct the problem.
• Keep a working fire extinguisher in the work area.

EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
See Technical Data in all equipment manuals.
• Use fluids that are compatible with equipment wetted
parts. See Technical Data in all equipment manuals.
Read fluid manufacturer’s warnings. For complete information about your material, request MSDS forms from
distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your
distributor for information.
• Route hoses and cables away from traffic areas, sharp
edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull
equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment
when operating, servicing, or in the operating area
of the equipment to help protect you from serious
injury. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and
solvent manufacturer
• Gloves
• Hearing protection

CALIFORNIA PROPOSITION 65
This product contains a chemical known to the State of
California to cause cancer, birth defects or other
reproductive harm. Wash hands after handling.

Pressure Relief Procedure

9.

Remove plug and use small screwdriver to remove all
components out front of gun.

WARNING
Follow this Pressure Relief Procedure whenever
you are instructed to relieve pressure, stop
spraying, check or service equipment or install or
clean spray tip.
1.

Turn OFF power and turn sprayer pressure control to
lowest pressure setting.

2.

Trigger gun into pail to relieve pressure.

ti8806a

ti8807a

Assembly
1.

Hold gun as shown and insert spring in front of gun.

Cleaning and Lubricating
Disassemble needle assembly and clean and grease o-rings
regularly to prolong gun life.

Disassembly

ti9271a

1.

Perform Pressure Relief Procedure (see above).

2.

Remove hopper or material hose from gun.

3.

Clean off as much material on gun body as possible.

4.

Turn flow adjustment nut counter-clockwise to enable
trigger to have full range of travel.

2.

Insert spring guide with o-ring into flow adjustment nut.
Make sure the protruded end of the guide points out as
shown.

3.

Position flow adjustment nut in seat on gun body.

4.

Apply a generous amount of grease to o-rings.

5.

Rest gun on air connection fitting. Slide needle into front
of gun.

ti8539a

5.

Using a small flat screwdriver, pry retaining ring off of
trigger pin. Remove pin, washer, and trigger.

ti8538a

6.

While pushing needle into gun, turn flow adjustment nut
counter-clockwise to tighten needle.

7.

Pull back on flow adjustment nut or continue pushing
needle in to make room for trigger.

ti8530a

6.

Unscrew nozzle and remove it from gun.

ti8532a

8.

Insert pin through trigger and washers. Push the retaining
clip onto the pin.

ti9273a

7.

Hold needle securely in place so it does not turn while
turning flow control clockwise until needle is disengaged
from thread and released. Pull needle and o-rings out
front of gun.

8.

Hold hand under trigger area to catch adjustment nut,
spring retainer, and spring. Tap gun lightly to loosen
spring or use a small screwdriver to loosen.

ti8538a

2

ti8530a

9.

Pull trigger and replace nozzle.

ti9272a

311777F

Parts Drawing and List
Model 288628 and 245924

Model 288629

3c

3e

27

3f
31
3d

3a

3d
3b

33

1B
6
10
8
20
(a,b,c,d)

21

9
21

32

22
ti8509a

16a
26

16c
20

3d 3c
21

3a

3d

2

3a
3b
3c
3d
3e
3f
6
8

15B168
234153
234154

8a
8b
8c
311777F

22

9

Description
GUN, complete, (for use with hopper)
GUN, complete, (non-hopper)
BODY, gun
BODY, gun
TRIGGER, gun, trigger
KIT, needle, repair
includes 3a, 3b, 3c, 3d, 3e, 3f
NEEDLE, includes o-ring
NUT, flow adjuster
GUIDE, needle
O-RING
SPRING
TAPE, foam
LOCK, trigger
KIT, nozzle, includes 8a, 8b, 8c, 8d
KIT, nozzle, includes 8a-8d, (HOME
DEPOT)
NOZZLE, fine, beige, 4m
NOZZLE, small, white, 6m
NOZZLE, medium, gray, 8m

1A
10

6

16b

8
(a,b,c,d)

Part
288628
288629
277393
277394
15F913
258000

2

27

3b

21

Ref.
A
B
1A
1B
2
3

3e

3f

ti8524a

Qty

1
1
1
1
1
1

1
1

Ref.
8d
9
10
16
16a
16b
16c
20
21
22
26
27
31
32
33

Part
169970
15B565
234162

118717
107243
115999
287967
15J635
234225
234188
234222

Description
NOZZLE, large, black, 10m
FITTING, line air
VALVE, ball
KIT, plug, includes 16a, 16b, 16c
PLUG, hopper
PLUG, hose, port
O-RING
PIN, clevis w/ring groove
WASHER
RING, retaining
PIN, clip gun
PLUG
KIT, hopper, 1.5 gallon (includes 32)
CLAMP
KIT, hopper, 0.75 gallon (includes 32)

Qty

1
1
1

1
2
1
1
1
1
1

Technical Data
Air Consumption

3.5-11 cfm at 15 to 100 psi

Weight

35 oz (1600 g)
3

Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 311777

Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2006, Graco Inc. is registered to ISO 9001
www.graco.com
Revised F August 2014



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseNone
XMP Toolkit                     : 3.1-701
Format                          : application/pdf
Creator                         : Kristine Beese
Description                     : Texture Guns
Title                           : 311777F, Texture Guns, Repair, US English
Subject                         : 311777, 311777F, 311777EN, 311777EN-F, MM 311777, Texture Guns, US English, 288628, 288629, 245924
Job Ref                         : Z087404
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Keywords                        : "311777, 311777F, 311777EN, 311777EN-F, MM 311777, Texture Guns, US English" 288628, 288629, 245924
Marked                          : True
Web Statement                   : 311777F  Texture Guns, US English
Copyright                       : 2006, Rev.F, August 2014
Create Date                     : 2004:10:18 09:44:46Z
Modify Date                     : 2014:09:08 15:53:31-05:00
Creator Tool                    : FrameMaker 11.0
Metadata Date                   : 2014:09:08 15:53:31-05:00
Document ID                     : uuid:418479f2-cef2-42c6-b31d-4a870b302cd8
Instance ID                     : uuid:68ac224e-9a8d-4d50-b8c7-8426f1261112
Page Count                      : 4
Language                        : en
Author                          : Kristine Beese
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools