Graco 312579K Airpro Gravitty Feed Airspray Gun Users Manual Gun, Parts Instructions, English
AirPro 312579 312579EN-K
2015-04-02
: Graco Graco-312579K-Airpro-Gravitty-Feed-Airspray-Gun-Users-Manual-686460 graco-312579k-airpro-gravitty-feed-airspray-gun-users-manual-686460 graco pdf
Open the PDF directly: View PDF 
.
Page Count: 22
| Download | |
| Open PDF In Browser | View PDF |
Instructions-Parts AirPro™ Gravity Feed Airspray Gun 312579K EN Conventional, HVLP, and compliant guns for specialty industrial applications. For professional use only. 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 3 for model information. ti11095A ll 2 G Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Gravity Feed without Cup . . . . . . . . . . . . . . . . . . 3 Gravity Feed with Plastic Cup . . . . . . . . . . . . . . . 3 Gravity Feed with 3M™ PPS™ Cup . . . . . . . . . . . 3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gun Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Conventional Guns . . . . . . . . . . . . . . . . . . . . . . . 5 HVLP Guns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Compliant Guns . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ground the Gun . . . . . . . . . . . . . . . . . . . . . . . . . 6 Flush Before Using Equipment . . . . . . . . . . . . . . 6 Adjust Spray Pattern . . . . . . . . . . . . . . . . . . . . . . 7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pressure Relief Procedure . . . . . . . . . . . . . . . . . 8 Apply Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Volatile Organic Compounds (VOC) Regulation . 8 Daily Gun Maintenance . . . . . . . . . . . . . . . . . . . . . . 9 General Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Clean Gun and Cup . . . . . . . . . . . . . . . . . . . . . . 9 Clean Nozzle and Air Cap . . . . . . . . . . . . . . . . . 10 Compliant Cleaning Methods . . . . . . . . . . . . . . 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 12 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Fluid Inlet Fitting Replacement . . . . . . . . . . . . . 14 Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Repair Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 22 Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 22 2 312579K Models Models Gravity Feed without Cup Conventional Orifice Size in. (mm) HVLP Compliant Max. Max. Max. HVLP/Compliant HVLP/Compliant HVLP/Compliant Air Pressure Air Pressure Air Pressure Model Series psi (MPa, bar) Model Series psi (MPa, bar) Model Series psi (MPa, bar) 0.055 (1.4) 289002 A N/A 289005 A 29 (0.2, 2.0) 289008 A 35 (0.24, 2.4) 0.070 (1.8) 289003 A N/A 289006 A 29 (0.2, 2.0) 289009 A 35 (0.24, 2.4) Gravity Feed with Plastic Cup Conventional Orifice Size in. (mm) HVLP Compliant Max. Max. Max. HVLP/Compliant HVLP/Compliant HVLP/Compliant Air Pressure Air Pressure Air Pressure Model Series psi (MPa, bar) Model Series psi (MPa, bar) Model Series psi (MPa, bar) 0.055 (1.4) 289011 A N/A 289014 A 29 (0.2, 2.0) 289017 A 35 (0.24, 2.4) 0.070 (1.8) 289012 A N/A 289015 A 29 (0.2, 2.0) 289018 A 35 (0.24, 2.4) Gravity Feed with 3M™ PPS™ Cup Conventional Orifice Size in. (mm) HVLP Compliant Max. Max. Max. HVLP/Compliant HVLP/Compliant HVLP/Compliant Air Pressure Air Pressure Air Pressure Model Series psi (MPa, bar) Model Series psi (MPa, bar) Model Series psi (MPa, bar) 0.055 (1.4) 289020 A N/A 289023 A 29 (0.2, 2.0) 289026 A 35 (0.24, 2.4) 0.070 (1.8) 289021 A N/A 289024 A 29 (0.2, 2.0) 289027 A 35 (0.24, 2.4) 312579K 3 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. Refer back to these warnings. Additional, productspecific warnings may be found throughout the body of this manual where applicable. WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • Use equipment only in well ventilated area. • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc). • Keep work area free of debris, including solvent, rags and gasoline. • Do not plug or unplug power cords or turn lights on or off when flammable fumes are present. • Ground all equipment in the work area. See Grounding instructions. • If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem. • Keep a working fire extinguisher in the work area. PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment. • Tighten all fluid connections before operating the equipment. • Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. • Check equipment daily. Repair or replace worn or damaged parts immediately. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your Graco distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not kink or overbend hoses or use hoses to pull equipment. • Keep children and animals away from work area. • Comply with all applicable safety regulations. 4 312579K Gun Selection WARNING PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to: • Protective eyewear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection Gun Selection Conventional Guns Compliant Guns Excellent atomization and high production rates typically with some reduction in transfer efficiency. A compliant gun is a high transfer efficiency gun which has been tested to have a transfer efficiency greater than or equal to HVLP guns. The Graco compliant guns have no restrictions on air cap pressures, but the gun inlet pressure must remain under 35 psi (0.24 MPa, 2.4 bar) to remain in compliance. HVLP Guns An HVLP gun is a high transfer efficiency gun which limits the air pressure at the air cap to 10 psi (0.07 MPa, 0.7 bar) maximum. In some areas, an HVLP gun is required for compliance with environmental standards. 312579K 5 Setup Setup 5. Connect the fluid supply to the fluid inlet fitting. fluid inlet • Check that your shop air provides adequate air flow. See Technical Data, page 20, for minimum cfm requirements. • Recommended 5/16 in. (7.9 mm) ID hose, optional 3/8 in. (10 mm) ID air hose. • Set shop air pressure regulator (not supplied) according to paint manufacturer’s recommendation. See maximum compliant air pressure on air cap. • Make sure no air restrictions, such as low-volume cheater-valves, obstruct the air flow. If an air adjusting valve is desired, use a Graco adjustable air valve (234784). 1. Shut off the air supply. 2. Install a shutoff valve (not supplied) downstream of the air regulator to shut off gun air. 3. Install an inline air filter (not supplied) to clean and dry the gun air supply. 4. Connect a clean, dry, filtered air supply to the air inlet fitting. See FIG. 1. 6 air inlet ti11306A FIG. 1 Ground the Gun Check your local electrical code for detailed grounding instructions. Ground the gun through connection to a Graco-approved conductive air supply hose. Flush Before Using Equipment The equipment was tested with lightweight oil, which is left in the fluid passages to protect parts. To avoid contaminating your fluid with oil, flush the equipment with a compatible solvent before using the equipment. See Flush, page 9. 312579K Setup Adjust Spray Pattern 1. Rotate the air cap to achieve desired spray pattern. See FIG. 2. 6. To reduce fluid flow, turn the fluid control valve clockwise. • • ti4839a If the fluid control valve is turned clockwise all the way, the gun will emit only air. If you cannot achieve the correct fluid flow with the fluid control valve, a different sized nozzle may be necessary. For smaller fluid flow, use the next size smaller nozzle. For a larger fluid flow, use the next size larger nozzle. 7. Spray a test pattern. Evaluate the spray pattern size and atomization. FIG. 2 2. To achieve full fan pattern, open the air control valve by turning the knob fully counterclockwise. See FIG. 3. 3. To create a round pattern, turn the pattern air off by turning the air control valve fully clockwise. See FIG. 3. 8. To achieve a narrow spray pattern, turn air control valve clockwise. 9. To improve atomization, reduce the fluid flow rate. Increasing the air pressure can improve atomization but may result in poor Transfer Efficiency (TE) or non-compliant operation. 4. Trigger gun and adjust gun air pressure. Refer to Technical Data, page 20, for inlet air pressure. 5. To establish the correct fluid flow, turn the fluid control valve counterclockwise until no restriction of the trigger movement is felt, then turn out another half turn. air control valve fluid control valve air inlet valve ti11097a FIG. 3 312579K 7 Operation Operation Pressure Relief Procedure 1. Turn off the gun air supply. 2. Trigger the gun to relieve pressure. When using the HVLP spray gun, instead of a conventional airspray gun, you may need to use a slightly slower hand movement and make fewer passes with the gun to coat a part. This is due to the reduced spray velocity produced by lower HVLP air pressures, along with a larger fluid particle size because there is less air to blow off solvents than is produced by conventional airspray. Take care to avoid runs or sags as you spray. Apply Fluid CAUTION Excessive atomizing air pressure can increase over-spray, reduce transfer efficiency, and result in a poor quality finish. Regulatory agencies in certain states prohibit the operation of a spray gun above 10 psi (69 kPa, 0.7 bar) atomizing air cap pressure. Volatile Organic Compounds (VOC) Regulation 1. Fill the cup with material. Do not fill past the full markings on cup. In certain states, spraying solvents that release VOCs into the atmosphere when cleaning a spray gun is prohibited. To comply with these air quality laws, you must use a cleaning method that prevents the escape of VOC vapors into the atmosphere. See Compliant Cleaning Methods, page 10. 2. Turn on the shop air to the gun. Set atomizing pressure with the gun fully triggered. Clean air line filters as directed by the manufacturer. 3. Adjust the pattern size and shape. See page 7. 4. To achieve the best results when applying fluid: • Keep the gun perpendicular and 6 to 8 inches (150 to 200 mm) from the object being sprayed. • Use smooth, parallel strokes across the surface to be sprayed with 50% overlap. See Troubleshooting, page 11, if you experience an irregular pattern. 8 312579K Daily Gun Maintenance Daily Gun Maintenance 2. Dispose of any paint in the cup. 3. Fill the cup with a small amount of solvent. 4. Spray into a grounded metal waste container until the equipment is clean. General Tasks Follow the Pressure Relief Procedure, page 8. • Frequently lubricate the gun moving parts with a drop of non-silicone oil. • Do not disassemble the spray gun if you are having a spray pattern problem. See Troubleshooting, page 11, for information on how to correct the problem. • Clean the fluid and air line filters daily. • Check for fluid leakage. Tighten fittings or replace equipment as needed. CAUTION Solvent left in gun air passages could result in a poor quality paint finish. Do not use any cleaning method that may allow solvent into the gun air passages. • • • Do not point gun up while cleaning it. Do not wipe gun with a cloth soaked in solvent; wring out the excess. Do not immerse the gun in solvent. Flush 5. Follow Pressure Relief Procedure, page 8. Clean Gun and Cup CAUTION • Do not submerge gun in solvent. Solvent dissolves lubricant, dries out packings, and clogs air passages. • Do not use metal tools to clean air cap holes as this may scratch them and distort the spray pattern. • Use a compatible solvent. 1. Flush, page 9. 2. Dampen a soft cloth with solvent and wring out the excess. Point the gun down and wipe off the outside of the gun and cup. 3. Make sure cup lid vent hole is clear. 4. Blow dry gun inside and out. Lubricate. See Compliant Cleaning Methods, page 10, to comply with air quality laws if applicable. Flush before using the equipment, before changing colors, and when you are done spraying. Use solvent that is compatible with gun wetted parts and with the fluid that will be sprayed. See Compliant Cleaning Methods, page 10, to comply with air quality laws if applicable. 1. Follow Pressure Relief Procedure, page 8. 312579K 9 Daily Gun Maintenance Clean Nozzle and Air Cap Compliant Cleaning Methods 1. Remove air cap (13), trigger gun, remove nozzle (11), and soak both in a compatible cleaning solution. 1. Place spray gun in a gun washer that completely encloses the gun and components during cleaning, rinsing, and draining. CAUTION Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle tip away from the nozzle seating surface and prevents the tip from being damaged. 2. Spray solvent through the spray gun into a closed gun cleaning station. 2. Clean air cap, nozzle, and front of the gun with a soft-bristle brush dipped into compatible solvent. Do not use a wire brush or metal tools. 3. Use a soft implement, such as a toothpick, to clean out air cap holes. 4. Trigger the gun while you install the fluid nozzle with the gun tool. Tighten the nozzle securely to 155-165 in-lb (17.5-18.6 N•m) to obtain a good seal. 5. Install the retaining ring (14) and air cap (13). When reassembling, make sure the air cap matches the color etched onto the side of the nozzle (gold, brown, grey, blue, etc.). 6. After cleaning the gun, lubricate the following parts with lubricant 111265 daily: • • • 10 fluid control valve threads trigger pivot pin fluid needle shaft 312579K Daily Gun Maintenance 312579K 11 Daily Gun Maintenance Troubleshooting Problem Spray Pattern Right Spray Pattern Cause Normal pattern. Solution No action necessary. Dirty or damaged air cap or fluid nozzle. Rotate air cap 180°. Wrong Heavy top or bottom Spray Pattern Wrong Split pattern Spray Pattern Pressure too high for viscosity of material being sprayed. If pattern follows air cap, problem is in air cap (13). Clean and inspect. If pattern is not corrected, replace air cap. If pattern does not follow the air cap, the problem is with the fluid nozzle. Clean and inspect the nozzle. If the pattern is not corrected, replace nozzle. Reduce air pressure and increase material viscosity. Correct pattern by narrowing fan size with fluid control valve (8). Dirty or distorted air horn holes. Clean and inspect air cap. If pattern is not corrected, replace air cap. Air getting into paint stream. Check if cup is empty and fill. Wrong Gun spitting Tighten fluid nozzle (11). Check and tighten needle packing nut (17). Check fluid nozzle (11) for damage. Will not spray 12 Damaged fluid nozzle seal (19). Cup is empty. Fluid control valve (8) turned too far clockwise. Replace fluid inlet gasket (3) Replace seal (19). Fill cup. Adjust valve (8) counterclockwise. 312579K Daily Gun Maintenance Problem Excessive air blowing back Cause Loose fluid nozzle (11). Damaged fluid nozzle seal (19). Excessive air leak Worn u-cups/air valve. behind trigger. Worn trigger. 312579K Solution Tighten fluid nozzle (11). Replace seal (19). Repair gun (Kit 289408). Be sure to use all included parts. Replace trigger (part 289140). If leak persists repair gun (Kit 289408). 13 Repair Repair Fluid Inlet Fitting Replacement Follow Pressure Relief Procedure, page 8. PRESSURIZED EQUIPMENT HAZARD See Parts, page 16, for callout references. • Disassembly 1. Unscrew retaining ring (14) to remove air cap (13b). Check o-rings (13a and 13c) and replace if necessary. 2. Trigger gun while unscrewing nozzle (11) to prevent needle damage. 3. Check o-ring (19) and replace if necessary. 4. Remove fluid control valve (8), spring (26), needle (9), and nut (7). Inspect. Replace tip (9c), needle (9), and u-cup seal (20) as necessary. If replacing needle tip, use low strength thread adhesive on needle tip threads. 5. Remove spring (28) and push the air valve assembly (6) out the back of the gun. Inspect. Replace air valve assembly (6) and u-cup seal (20) as necessary. Use tool (33) to install u-cup seal. • Fluid inlet gasket (3) must be replaced if fluid inlet fitting (4) is removed from spray gun. Failure to replace gasket (3) may result in air leakage into the fluid section causing a non-vented gravity cup to become pressurized. 1. Remove fluid inlet fitting (4). 2. Remove fluid inlet gasket (3) from gun body and discard. 3. Apply thread sealant to replacement fluid inlet fitting (4) threads. 4. Snap the fluid inlet gasket (3) securely onto the fluid inlet fitting (4). 5. Screw in fluid inlet fitting (4) and torque to 155-165 in.-lb (17.5-18.6 N•m). 6. Replace washer (28) as required. 6. Remove trigger nut (22), trigger pin (21), wave washer (18), and trigger (10). 7. Unscrew needle packing nut (17) and remove u-cup packing (16) and spreader (15). 8. Remove air control valve assembly (5). Inspect and replace as necessary. 9. Remove air inlet valve assembly (27). Inspect and replace as necessary. 14 312579K Repair Reassembly 1. Install air control valve assembly (5) with valve turned fully counterclockwise to outermost position. Torque to 85-90 in-lb (9.6-10.2 N•m). 2. Install air inlet valve assembly (27) with valve turned fully counterclockwise to outermost position. Torque to 205-215 in-lb (23.2-24.3 N•m). 3. Lubricate u-cup spreader (15) and u-cup packing (16). Install spreader (15) with tapered end facing rear of gun. Install u-cup packing (16) with open end facing front of gun. Install packing nut (17). Torque to 3 in-lb (0.3 N•m). 17 16 15 312579K 4. Install wave washer (18) with cupped side toward the gun body. Lubricate and apply thread retainer to trigger pin (10). Install trigger (10), trigger pin (21), and trigger nut (22). Torque to 15-20 in-lb (1.7-2.2 N•m). 5. Install air valve assembly (6), spring (28), and nut (7). Torque to 175-185 in-lb (19.8-20.9 N•m). 6. Install needle (9) and spring (26). Lightly lubricate and install fluid control valve (8). 7. Trigger gun while replacing nozzle (11). Torque to 155-165 in-lb (17.5-18.6 N•m). 8. Install air cap assembly (13) and retaining ring (14). ti11226a 15 Parts Parts 8 7 3 8 28 3 20 3 56 10 37 4 5 9 20 3 3 18 6 3 21 3 19 11 9 1 13b 3 13c 26 9a 9b 4 3 9c 4 7 22 1 12 17 2 3 16 11 23 15 2 13a 10 11 10 27 36 3 14 11 ti11224a 1 2 3 4 5 6 7 8 9 10 11 12 16 Pull trigger before installing nozzle (11). Insert spreader (15) with tapered end facing rear of gun. Insert u-cup (16) with open end facing front of gun. Apply lubricant. Apply low strength thread retainer. Apply thread sealant. Torque to 85-90 in-lb (9.6-10.2 N•m). Torque to 15-20 in-lb (1.7-2.2 N•m). Torque to 175-185 in-lb (19.8-20.9 N•m). Torque to 155-165 in-lb (17.5-18.6 N•m). Install with valve assembly turned fully counterclockwise to outermost position. Torque to 205-215 in-lb (23.2-24.3 N•m). Torque to 3 in-lb (0.3 N•m). 312579K Parts Ref. 1❄ 3❄† 4❄ Part No. Description Qty. --BODY, gun 1 --GASKET, fluid inlet 1 289792 FITTING, fluid inlet, 1 includes gasket (item 3) 5 289796 VALVE, air control 1 assembly 6*★ 289039 VALVE, air, assembly 1 7* 289052 NUT, air valve, u-cup 1 assembly 8 289097 VALVE, fluid control 1 9 See p. 19 NEEDLE, assembly 1 --9a NUT, needle 1 --9b NEEDLE 1 9c See p. 19 TIP, needle 1 10 289140 TRIGGER 1 11 See p. 19 NOZZLE, fluid 1 13 See p. 19 AIR CAP, assembly 1 (includes 13a-13c) --WASHER 1 13a★◆✓ --13b★◆✓ O-RING 1 13c See p. 19 AIR CAP 1 --14✓ RING, retaining 1 --15★+ SPREADER, u-cup 1 --16★+ PACKING, u-cup 1 17 289793 NUT 1 --18✖ WASHER, wave 1 19★ 111457 O-RING 1 --PACKING, u-cup 1 20* --21✖ PIN, pivot 1 --22✖ NUT, pivot pin 1 23 289451 FITTING, air inlet 1 --26* SPRING, compression 1 Ref. 27 Part No. Description Qty. 289142 VALVE, assembly, 1 air inlet --28* SPRING, compression 1 29 289794 TOOL, gun 1 --33*★ TOOL, installation, 1 seal 36 289452 NUT, air plug, 1 not assembled --37❖★ WASHER, uhmw 1 38 289770 CUP, gravity, 650 cc 1 38a 289195 FILTER, cup (not shown) ★ Included in Gun Repair Kit 289790. ✖ Included in Trigger Repair Kit 289143 (contains 5 of each part). + Included in Needle Packing Repair Kit 289455 (contains 5 of each part). * Included in Air Valve Repair Kit 289408. ◆ Included in Air Cap Seal Kit 289791 (contains 5 of each part). ✓ Included in Retaining Ring Kit 289079. ❖ Included in Cup Gasket Repair Kit 289213 (pack of 10). ❄ Included in Gun Body Kit 289022. † Included in Fluid Inlet Gasket Kit 24A560, package of 5 (purchase separately). --- Not sold separately. 312579K 17 Accessories Accessories Cups Part No. 289797 289802 289770 192407 3M™ PPS™ Cups and Accessories Description Cup, aluminum, 23 oz (650 cc) Cup, aluminum, 34 oz (1 liter) Cup, plastic, 23 oz (650 cc) Cup Holder Repair Kits Part No. 289455 289790 289791 289143 289408 289213 289079 289022 24A560 24C310 195065 Description Needle Packing Repair Kit Gun Repair Kit Air Cap Seal Kit Trigger Repair Kit Air Valve Repair Kit Cup Gasket Kit, 10 pack Retaining Ring Kit Gun Handle Replacement Kit Fluid Inlet Gasket Kit, 5 pack Nozzle O-Ring Kit, 5-pack Steel Air Inlet Fitting Air Valves Part No. 234784 235119 239655 Description Air Control Valve with Gauge Gun Air Regulator Assembly Swivel Air Valve Cleaning Kit Part No. 105749 111265 15C161 18 Description Cleaning Brush Gun Lubricant Ultimate Gun Cleaning Kit Part No. 234941 234771 234937 234940 234772 234938 234942 15F531 234939 289486 289795 15E470 15E469 15E467 Description Cup and Collar, 6 oz, 8-pack Cup and Collar 25 oz, 8-pack Cup and Collar 32oz, 4-pack Lid and Liner, 6 oz, 50-pack Lid and Liner, 25 oz, 50-pack Lid and Liner, 32 oz, 25-pack Ratio Film, insert, 6 oz, 50-pack Ratio Film, insert, 25 oz, 100-pack Ratio Film, insert, 32 oz, 100-pack Gravity Cup Assembly, 25 oz, includes cup, collar, lid, liner, and adapter Gravity Feed Adapter Lid Dispenser Liner Dispenser Gun Tray Test Gauge Part No. Description 289803 HVLP Verification Hoses Part No. 239631 239636 239637 Description 4 ft Air Whip Hose Assembly (5/16 in.) 15 ft Air Hose Assembly (5/16 in.) 25 ft Air Hose Assembly (5/16 in.) Tips Part No. Description 24E484 .030 SST Needle Tips (Pack of 5) 312579K Repair Kits Repair Kits Without Gravity Cup Model Spray Type Nozzle Size in. (mm) Air Cap Nozzle Needle Needle/ Needle Tip Kit Kit Assembly Kit Nozzle Kit Kit (13a-13c) (11, 19) (9a-9c) (9a-9c, 11, 19) (9c, 5-pack) 289002 Conventional 0.055 (1.4) 289773 289780 289799 289493 288185 289003 Conventional 0.070 (1.8) 289773 289767 289786 289494 289001 289005 HVLP 0.055 (1.4) 289771 289776 289786 289495 289001 289006 HVLP 0.070 (1.8) 289771 289801 289786 289496 289001 289008 Compliant 0.055 (1.4) 289772 289779 289799 289497 288185 289009 Compliant 0.070 (1.8) 289772 289559 289799 289498 288185 Nozzle Kit (11, 19) Needle Assembly Kit (9a-9c) Needle/ Nozzle Kits (9a-9c, 11, 19) Needle Tip Kit (9c, 5-pack)) With Gravity Cup Nozzle Size Air Cap Kit in. (mm) (13a-13c) Model Spray Type 289011 Conventional 0.055 (1.4) 289773 289780 289799 289493 288185 289012 Conventional 0.070 (1.8) 289773 289767 289786 289494 289001 289014 HVLP 0.055 (1.4) 289771 289776 289786 289495 289001 289015 HVLP 0.070 (1.8) 289771 289801 289786 289496 289001 289017 Compliant 0.055 (1.4) 289772 289779 289799 289497 288185 289018 Compliant 0.070 (1.8) 289772 289559 289799 289498 288185 Nozzle Kit (11, 19) Needle Assembly Kit (9a-9c) Needle/ Nozzle Kits (9a-9c, 11, 19) Needle Tip Kit (9c, 5-pack)) With 3M PPS Cup Nozzle Size Air Cap Kit in. (mm) (13a-13c) Model Spray Type 289020 Conventional 0.055 (1.4) 289773 289780 289799 289493 288185 289021 Conventional 0.070 (1.8) 289773 289767 289786 289494 289001 289023 HVLP 0.055 (1.4) 289771 289776 289786 289495 289001 289024 HVLP 0.070 (1.8) 289771 289801 289786 289496 289001 289026 Compliant 0.055 (1.4) 289772 289779 289799 289497 288185 289027 Compliant 0.070 (1.8) 289772 289559 289799 289498 288185 Needle Tips Grooves Grooves Needle Tip Kit (5-pack) 4 288185 7 289001 ti14043a 312579K 19 Technical Data Technical Data Maximum Air Inlet Pressure . . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar) Maximum HVLP/Compliant Inbound Air Pressure: HVLP gravity feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 psi (0.2 MPa, 2.0 bar)* Compliant gravity feed. . . . . . . . . . . . . . . . . . . . . . . . . . 35 psi (0.24 MPa, 2.4 bar)* Air Consumption: Conventional Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 CFM at 43 psi (0.3 MPa, 3.0 bar) HVLP Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 CFM at 29 psi (0.2 MPa, 2.0 bar) Compliant Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 CFM at 35 psi (0.24 MPa, 2.4 bar) Fluid and Air Operating Temperature Range 32°F to 109°F (0°C to 43°C) Spray Gun: Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npsm (R1/4-19) Weight with cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 lbs (0.6 kg) Sound Data: Conventional Sound pressure at 43 psi (0.3 MPa, 3.0 bar). . . . . . . . 79.52 dB(A)** Sound power at 43 psi (0.3 MPa, 3.0 bar) . . . . . . . . . . 88.05 dB(A)** HVLP Sound pressure at 29 psi (0.2 MPa, 2.0 bar). . . . . . . . 83.9 dB(A)** Sound power at 29 psi (0.2 MPa, 2.0 bar) . . . . . . . . . . 90.8 dB(A)** Compliant Sound pressure at 35 psi (0.24 MPa, 2.4 bar). . . . . . . 81.8 dB(A)** Sound power at 35 psi (0.24 MPa, 2.4 bar) . . . . . . . . . 88.7 dB(A)** Gravity Cup Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 oz (0.68 liter) cup Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 stainless steel, 17-4 PH stainless steel, PEEK, acetal, UHMWPE * Produces 10 psi (0.07 MPa, 0.7 bar) spraying pressure at air cap. ** All readings were taken with the fan valve fully open (fan full size) at the assumed operator position. Sound power was tested per ISO 9614-2. 20 312579K Technical Data 312579K 21 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products visit www.graco.com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505 All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 312579 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2007, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com Revised 10/2011
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Producer : Acrobat Distiller 7.0.5 (Windows) Job Ref : Z066448 Copyright : 2007, Rev K 10/2011 Marked : True Keywords : "312579, AirPro, Gravity Feed, Airspray, 289002, 289003, 289005, 289006, 289008, 289009. 289011, 289012, 289014, 289015, 289017, 289018, 289020, 289021, 289023, 289024, 289026, 289027" Web Statement : 312579, AirPro Gravity Feed Airspray, Gun, Parts/Instructions Create Date : 2005:04:27 11:19:54Z Creator Tool : FrameMaker 9.0 Modify Date : 2013:09:27 12:33:16-05:00 Metadata Date : 2013:09:27 12:33:16-05:00 Format : application/pdf Creator : Bill Jorgenson Description : 312579, AirPro Gravity Feed Airspray Gun, Parts/Instructions Title : 312579K - AirPro Gravitty Feed Airspray Gun, Parts-Instructions, English Subject : 312579, AirPro, Gravity Feed, Airspray, 289002, 289003, 289005, 289006, 289008, 289009. 289011, 289012, 289014, 289015, 289017, 289018, 289020, 289021, 289023, 289024, 289026, 289027 Document ID : uuid:5cc3693e-3712-4a4c-b1f6-a1165ff9876f Instance ID : uuid:f506b47a-dd3d-4628-bff3-9bc51c529d43 Page Count : 22 Author : Bill JorgensonEXIF Metadata provided by EXIF.tools