Graco 312830G Sg2 Sg3 Spray Guns Users Manual SG2, Guns, Instructions Parts (English)
243382 312830EN-G
16x214 7637d016-ad34-4e9c-b86d-8d6005a80705 Graco Paint Sprayer 16X214 User Guide |
2015-04-02
: Graco Graco-312830G-Sg2-Sg3-Spray-Guns-Users-Manual-686499 graco-312830g-sg2-sg3-spray-guns-users-manual-686499 graco pdf
Open the PDF directly: View PDF 
.
Page Count: 4
ti11562a
EN
SG2, SG3 Spray Guns
Models: 243011, 243012, 246506, 243238,
243382, 289843, 257359, 16W431, 16X214
Maximum Working Pressure: 3600 psi (248 bar, 24.8 MPa)
-
For the application of architectural paints and coatings -
The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point
symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.
Additional, product-specific warnings may be found throughout the body of this manual where applicable.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured
components will pierce skin. This may look like just a
cut, but it is a serious injury that can result in amputation. Get
immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove,
or rag.
• Do not spray without tip guard and trigger guard
installed.
• Engage trigger lock when not spraying.
•
Follow Pressure Relief Procedure in this manual, when
you stop spraying and before cleaning, checking, or ser-
vicing equipment
.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes,
in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, ciga-
rettes, portable electric lamps, and plastic drop cloths
(potential static arc).
• Keep work area free of debris, including solvent, rags
and gasoline.
• Do not plug or unplug power cords, or turn power or light
switches on or off when flammable fumes are present.
• Ground all equipment in the work area. See Grounding
instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering
into pail.
• If there is static sparking or you feel a shock, stop oper-
ation immediately. Do not use equipment until you iden-
tify and correct the problem.
• Keep a working fire extinguisher in the work area.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influ-
ence of drugs or alcohol.
• Do not exceed the maximum working pressure or tem-
perature rating of the lowest rated system component.
See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equip-
ment wetted parts. See Technical Data in all equipment
manuals. Read fluid and solvent manufacturer’s warn-
ings. For complete information about your material,
request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or dam-
aged parts immediately with genuine manufacturer’s
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your
distributor for information.
• Route hoses and cables away from traffic areas, sharp
edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull
equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chlo-
ride, other halogenated hydrocarbon solvents or flu-
ids containing such solvents in pressurized aluminum
equipment. Such use can cause serious chemical reaction
and equipment rupture, and result in death, serious injury,
and property damage.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment
when operating, servicing, or in the operating area of
the equipment to help protect you from serious
injury. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and
solvent manufacturer
• Gloves
• Hearing protection
WARNINGS
312830G
IMPORTANT SAFETY INSTRUCTIONS.
Refer to your
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Keep these instructions.
Instructions/Parts
English
2312830G
Pressure Relief Procedure
Follow this Pressure Relief Procedure
whenever instructed to relieve pressure,
stop spraying, check or service equipment,
or install or clean spray tip.
1. Turn OFF power and turn sprayer pressure control to low-
est pressure setting.
2. Hold gun against side of flushing pail. Trigger gun into pail
to relieve pressure.
If you suspect spray tip or hose is clogged or that pressure has
not been fully relieved after following the steps above, VERY
SLOWLY loosen tip guard retaining nut or hose end coupling
to relieve pressure gradually, then loosen completely. Clear
hose or tip obstruction.
Gun Trigger Lock
To prevent injury when the gun is not in use, always
set the gun’s trigger lock if unit is being shut down
or left unattended.
Setup
Make sure sprayer is turned off and unplugged from power
source. Refer to your sprayer instruction manual for priming
and spray instructions.
Connect Gun to Sprayer
1. Attach supply hose to sprayer fluid outlet.
2. Attach other end of supply hose to gun swivel (5). Use two
wrenches (one on the swivel (5) and one on the hose), to
tighten all connections securely.
3. Refer to sprayer instruction manual for priming
instructions.
Installing Tip (26) and Guard (25) on Gun
1.If equipment has recently been operated,
relieve pressure. Set trigger lock.
2.Using a pencil or similar object, insert seal
(24) into back of guard (25).
3. Install guard (25) over end of gun (1).
4. Insert tip (26) in guard (25). Tighten retaining nut.
Operation
Spraying
1. Unlock trigger lock.
2. Be sure the arrow shaped tip (26) faces forward (spray).
3. Hold gun perpendicular and approximately 12-inches
(30 cm) from surface. Move gun first, then pull gun trigger
(3) to spray a test pattern.
4. Slowly increase pump pressure until coverage is uniform
and even (see sprayer instruction manual for additional
information).
Aligning Spray
1.Relieve pressure. Set trigger lock.
2. Loosen guard
retaining nut.
3. Align guard (25)
horizontally to
spray a horizontal
pattern.
4. Align guard (25)
vertically to spray
a vertical pattern.
Clearing Clogs
1. Relieve pressure. Set trigger lock.
2. Rotate tip (26) 180°. Unlock trigger lock. Trigger gun into
pail or onto ground to remove clog.
3. Set trigger lock. Rotate tip (26) 180° back to spray
position.
Cleanup
Flush gun after each work shift and store in a dry location. Do
not leave the gun or any parts in water or cleaning solvents.
WARNING
WARNING
WARNING
Trigger Locked
(no spray)
Trigger Unlocked
(spray)
ti11309a ti11308a
WARNING
WARNING
WARNING
(4) Vertical
(3) Horizontal
ti11564a ti11563a
312830G 3
Parts
33
26
5
1a
4
6
23
ti15355a
1c
8
24
22
7
32
3
1b
10
*Kit 288817 repairs both
series A and B guns.
Series B
Series A
1a replaces these three
components of series A.
1a
Ref. Part Description Qty.
1 288817 KIT, repair, gun (includes 1a, 1b, 1c) 1
1a SEAT, valve 1
1b NEEDLE, gun 1
1c 115483 NUT, lock 1
3 243639 TRIGGER, repair kit
includes 10, 32, 33
4 195495 GUARD, trigger 1
5 238817 KIT, swivel 1
195384 ADAPTER, gun inlet (SG2) 1
6✓288749 FILTER, gun 1
7✓179733 SEAL, sleeve 1
8 195395 CAP, end 1
10 115484 PIN, actuator 2
22 113409 RETAINER, guard 1
23 195393 HANDLE, gun (SG2) 1
195788 HANDLE, gun (SG3, SG3-E) 1
195920 HANDLE, gun (SG3-A) 1
24 115485 O-RING 1
26 195389 HOUSING, fluid 1
32 177538 STUD, trigger 1
33 105334 NUT, lock, hex 1
▲ Replacement Warning labels, tags and cards are available
at no cost.
✓ Keep these spare parts on hand to reduce down time
Ref. Part Description Qty.
Ref Part Description Qty
24 243004 OneSeal
™
, RAC IV (2-pack) 1
243281 OneSeal
™
, RAC 5 (5-pack) 1
246453 OneSeal
™
, RAC X (5-pack) 1
25 237859 GUARD, RAC IV 1
243161 GUARD, RAC 5 1
246215 GUARD, RAC X 1
26 221515 TIP, spray 515, RAC IV 1
286515 TIP, spray 515, RAC 5 1
LTX515 TIP, spray 515, RAC X 1
221517 TIP, spray 517, RAC IV 1
262515 TIP, spray 515, RAC 5 1
RAC X
RAC 5
25 26
24
24
25 26
ti11561a
ti8505b
RAC IV
24
25 26
ti11739a
For complete warranty information contact your local Graco distributor, call Graco customer service:
1-800-690-2894 or visit our website: www.graco.com.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
This manual contains English. MM 312830
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2008, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised July 2014
Maintenance
Before performing any maintenance on gun, read all warnings on front
cover of this manual and relieve pressure.
Cleaning/Replacing Filter (6)
1.
Relieve pressure. Set trigger lock
2. Disconnect fluid hose from gun at swivel (5).
3. Disconnect trigger guard (4) from guard retainer (22).
4. Unscrew handle (23) from gun (1).
5. Remove filter (6) through top of handle (23).
6. Clean filter (6). Use a soft brush to loosen and remove excess
debris.
7. Insert clean filter (6) into handle (23).
8. Reattach handle (23) to gun (1). Tighten securely.
9. Reconnect trigger guard (4) to guard retainer (22).
Translated Manuals
Repair
Replacing Needle
1. Relieve pressure. Set trigger lock.
2. Remove tip (26) and guard (25) from gun (1).
3. Disconnect fluid hose from gun at swivel (5).
4. Squeeze trigger while unscrewing diffuser.
5. Remove locknut and end cap.
6. Tap out needle.
7. Use a soft brush to clean out internal passages of gun.
8. Grease o-rings of new needle using a non-silicon grease.
9. Guide new needle (15b) through front of gun .
10. Install end cap and locknut, loosely.
11. For needle housing (15a), apply medium strength (blue) thread
sealant to threads.
12. Squeeze trigger while installing needle housing. Torque to 26-32
ft-lb (35-43 N•m).
13. Hold gun with nozzle facing up.
14. Set trigger lock.
15. Turn locknut (a) clockwise until you see and feel trigger (3) raise
slightly.
16. Turn locknut (a) 3/4 turn counter-clockwise.
NOTE: When needle is properly adjusted, trigger will move freely.
17. Connect fluid hose. Install tip (26) and guard (25).
18. Prime sprayer. See sprayer instruction manual.
19. Trigger gun into bucket until fluid flows from gun.
20. Release trigger (3). Fluid flow should stop immediately.
21. Set trigger lock.
22. Aim gun into bucket. Trigger gun. No fluid should flow.
23. If the gun fails tests, steps 19 and/or 21, relieve pressure and
disconnect hose. Readjust needle. Repeat tests.
Technical Data
WARNING
French - 312831 Estonian - 312845
Spanish - 312832 Latvian - 312846
Dutch - 312833 Lithuanian - 312847
German - 312834 Polish - 312848
Italian - 312835 Hungarian - 312849
Turkish - 312836 Czech - 312850
Greek - 312837 Slovakian - 312851
Croatian - 312838 Slovenian - 312852
Portuguese - 312839 Romanian - 312853
Danish - 312840 Bulgarian - 312854
Finnish - 312841 Chinese - 312855
Swedish - 312842 Japanese - 312856
Norwegian - 312843 Korean - 312857
Russian - 312844
WARNING
16
17
a
ti11311b
15b
1
15a
Maximum working pressure 3600 psi (248 bar, 24.8 MPa)
Fluid orifice size 0.125 in. (3.18 mm)
Weight (with tip and guard) 22 oz. (630 g)
Inlet
Maximum material temperature 120 F (49 C)
Wetted Parts Stainless steel, polyurethane, nylon, aluminum, tungsten carbide, brass
*Noise Level: Sound power 87 dBa
Sound pressure 78 dBa
*Measured at 3.1 ft (1m) while spraying water-based paint, specific gravity 1.36, through a 517 tip at 3000 psi (207 bar, 20.7 MPa) per ISO 3744
Translated manuals can be requested through a distributor
or at www.graco.com.
