Graco 332916C 695 795 1095 1595 Markiv Mark V Vii X Users Manual 695/795/1095/1595/MarkIV/Mark V/Mark VII/Mark Electric Airless Sprayers Operation (English) Noptc
b8782e18-4c0a-474d-b313-10f6f3d3cc20 Graco Paint Sprayer 1095 User Guide |
2015-04-02
: Graco Graco-332916C-695-795-1095-1595-Markiv-Mark-V-Mark-Vii-Mark-X-Users-Manual-686192 graco-332916c-695-795-1095-1595-markiv-mark-v-mark-vii-mark-x-users-manual-686192 graco pdf
Open the PDF directly: View PDF 
.
Page Count: 44
- Models
- Warnings
- Component Identification
- Grounding
- 10/16 Amp Switch
- 15/20 Amp Switch
- Pressure Relief Procedure
- Setup
- Startup
- Switch Tip Installation
- Spray
- Clearing Tip Clog
- Fast Flush (ProContractor and IronMan models only)
- WatchDog™ Protection System (ProContractor and IronMan models only)
- ProGuard
- Hose Reel
- Digital Tracking System (ProContractor and IronMan models only)
- Cleanup
- Troubleshooting
- Technical Data
- Graco Standard Warranty
332916C
EN
Operation
695 / 795 / 1095 / 1595 / Mark IV / Mark V / Mark VII / Mark X
Electric Airless Sprayers
For Portable Airless Spraying of Architectural Coatings and Paints.
For professional use only. Not approved for use in European explosive atmosphere locations.
3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
ti22882a
Standard Hi-Boy Series ProContractor Series
IronMan Series
Standard Lo-Boy Series
Related Manuals:
332918
333281
309495
308491
311861
311254
333028
332922
2332916C
Table of Contents
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
UltraMax II, Ultimate Max II Models: . . . . . . . . . . 3
TexSpray Models: . . . . . . . . . . . . . . . . . . . . . . . . 4
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Component Identification . . . . . . . . . . . . . . . . . . . . 8
695 / 795 / 1095 / 1595 / Mark IV / Mark V / Mark VII
/ Mark X
Standard Models: . . . . . . . . . . . . . . . . . . . . . 8
695 / 795 / 1095 / 1595 Mark IV / Mark V / Mark VII /
Mark X ProContractor Models: . . . . . . . . . . . 9
1095 / 1595 / Mark V IronMan Models: . . . . . . . 10
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Requirements . . . . . . . . . . . . . . . . . . . . 11
Extension Cords . . . . . . . . . . . . . . . . . . . . . . . . 11
Pails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10/16 Amp Switch . . . . . . . . . . . . . . . . . . . . . . . . . 12
15/20 Amp Switch . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 13
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Switch Tip Installation . . . . . . . . . . . . . . . . . . . . . . 16
Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clearing Tip Clog . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fast Flush
(ProContractor and IronMan models only) . . 17
WatchDog
™
Protection System
(ProContractor and IronMan models only) . . 17
ProGuard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Standard Models . . . . . . . . . . . . . . . . . . . . . . . . 18
ProContractor and IronMan Models . . . . . . . . . 18
Hose Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
(ProContractor models only) . . . . . . . . . . . . . . . 19
Digital Tracking System
(ProContractor and IronMan models only) . . 20
Operation Main Menu . . . . . . . . . . . . . . . . . . . . 20
Change Display Units . . . . . . . . . . . . . . . . . . . . 20
Job Gallons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lifetime Gallons . . . . . . . . . . . . . . . . . . . . . . . . . 20
Secondary Menu - Stored Data . . . . . . . . . . . . . 21
Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Mechanical/Fluid Flow . . . . . . . . . . . . . . . . . . . . 24
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 44
Models
332916C 3
Models
UltraMax II, Ultimate Max II Models:
695 UltraMax, Standard, ProContractor, IronMan Models
Model Voltage Standard Hi-Boy Standard Lo-Boy ProContractor IronMan
16W892 120
✓
16W893 120
✓
16W894 120
✓
826177 120
✓
826178 120
✓
826179 120
✓
16X656 230
✓
16X657 230
✓
16X658 120
✓
16X659 120
✓
16X660 230
✓
16X811 120
✓
16X812 230
✓
16Y635 230
✓
16Y637 230
✓
16Y638 120
✓
16Y639 230
✓
795 UltraMax, Standard, ProContractor, IronMan Models
16W895 120
✓
16W896 120
✓
826180 120
✓
826181 120
✓
16X813 230
✓
16X870 230
✓
16X871 230
✓
16X872 120
✓
16X873 230
✓
16Y895 230
✓
16Y896 230
✓
16Y897 230
✓
16Y898 120
✓
16Y899 120
✓
1095 UltraMax, Standard, ProContractor, IronMan Models
16W899 120
✓
16W900 120
✓
16W901 120
✓
826182 120
✓
826183 120
✓
826184 120
✓
16X874 230
✓
16X875 230
✓
16X881 230
✓
16X882 120
✓
16Y829 230
✓
16Y830 230
✓
16Y831 120
✓
16Y832 230
✓
16Y833 120
✓
16Y869 230
✓
16Y871 230
✓
Models
4332916C
TexSpray Models:
1595 UltraMax, Standard, ProContractor, IronMan Models
Model Voltage Standard Hi-Boy Standard Lo-Boy ProContractor IronMan
16W902 120
✓
16W903 120
✓
16W907 120
✓
16W936 120
✓
16W937 120
✓
16W938 120
✓
826185 120
✓
826186 120
✓
826187 120
✓
826188 120
✓
826189 120
✓
826190 120
✓
Mark IV / Mark V / Mark VII / Mark X Standard, ProContractor, IronMan Models
Model
Number Model Voltage Standard
Hi-Boy
Pro
Contractor IronMan
Flex
Plus
Gun
Blue
Texture
Gun
HD
Inline
Texture
Gun
3/8 in. x 50ft +
1/4 in. x 3 ft
whip
(9.5mm x 15m
+ 6.4mm x
0.9m whip)
3/8 in. x 100 ft
+ 1/4 in. x 3 ft
whip
(9.5mm x 30m
+ 6.4mm x
0.9m whip)
1/2 in. x 50 ft +
3/8 in. x 12 ft
whip
(12.7mm x 15m
+ 9.5mm x
3.7m whip)
1/2 in. x 100 ft
+ 3/8 in. x 12 ft
whip
(12.7mm x 30m
+ 9.5mm x
3.7m whip)
16W897 Mark IV 120 ✓✓ ✓
16W898 Mark IV 120 ✓✓ ✓
16X953 Mark IV 230 ✓✓ ✓
16X954 Mark IV 230 ✓✓ ✓
16X956 Mark IV 230 ✓✓ ✓
16Y892 Mark IV 230 ✓✓ ✓
16Y893 Mark IV 230 ✓✓ ✓
16Y894 Mark IV 230 ✓✓ ✓
16W905 Mark V 120 ✓✓✓
16W906 Mark V 120 ✓✓ ✓
16W939 Mark V 120 ✓✓✓
16W940 Mark V 120 ✓✓ ✓
16X944 Mark V 230 ✓✓✓
16X947 Mark V 120 ✓✓ ✓
16X965 Mark V 230 ✓✓✓
16X966 Mark V 120 ✓✓✓
16X967 Mark V 230 ✓✓✓
16Y533 Mark V 120 ✓✓ ✓
16Y864 Mark V 230 ✓✓ ✓
16Y865 Mark V 230 ✓✓ ✓
16Y866 Mark V 120 ✓✓ ✓
16Y867 Mark V 230 ✓✓ ✓
16Y868 Mark V 120 ✓✓ ✓
16Y872 Mark V 230 ✓✓ ✓
16Y874 Mark V 230 ✓✓ ✓
16Y763 Mark VII 230 ✓✓✓
16Y919 Mark VII 230 ✓✓✓
16Y920 Mark VII 230 ✓✓ ✓
16Y921 Mark VII 230 ✓✓ ✓
16W908 Mark X 230 ✓✓✓
16X099 Mark X 230 ✓✓ ✓
16Y534 Mark X 230 ✓✓✓
16Y535 Mark X 230 ✓✓✓
16Y536 Mark X 230 ✓✓✓
16Y910 Mark X 230 ✓✓ ✓
16Y912 Mark X 230 ✓✓ ✓
16Y913 Mark X 230 ✓✓ ✓
Warnings
332916C 5
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where
applicable.
WARNING
GROUNDING
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
•Improper installation of the grounding plug is able to result in a risk of electric shock.
•When repair or replacement of the cord or plug is required, do not connect the grounding wire to
either flat blade terminal.
•The wire with insulation having an outer surface that is green with or without yellow stripes is the
grounding wire.
•Check with a qualified electrician or serviceman when the grounding instructions are not completely
understood, or when in doubt as to whether the product is properly grounded.
•Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qual-
ified electrician.
•This product is for use on a nominal 120V or 230V circuit and has a grounding plug similar to the
plugs illustrated in the figure below.
•Only connect the product to an outlet having the same configuration as the plug.
•Do not use an adapter with this product.
Extension Cords:
•Use only a 3-wire extension cord that has a grounding plug and a grounding receptacle that accepts
the plug on the product.
•Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG
(2.5 mm
2
) minimum to carry the current that the product draws.
•An undersized cord results in a drop in line voltage and loss of power and overheating.
120V US 230V
Warnings
6332916C
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
•Do not spray flammable or combustible materials near an open flame or sources of ignition such as
cigarettes, motors, and electrical equipment.
•Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity
creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray sys-
tem, including the pump, hose assembly, spray gun, and objects in and around the spray area shall
be properly grounded to protect against static discharge and sparks. Use Graco conductive or
grounded high-pressure airless paint sprayer hoses.
•Verify that all containers and collection systems are grounded to prevent static discharge. Do not
use pail liners unless they are are antistatic or conductive.
•Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.
•Do not use a paint or a solvent containing halogenated hydrocarbons.
•Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep
pump assembly in a well ventilated area. Do not spray pump assembly.
•Do not smoke in the spray area.
•Do not operate light switches, engines, or similar spark producing products in the spray area.
•Keep area clean and free of paint or solvent containers, rags, and other flammable materials.
•Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets
(MSDS) and container labels provided with the paints and solvents. Follow the paint and solvents
manufacturer’s safety instructions.
•Fire extinguisher equipment shall be present and working.
•Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or
cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors.
SKIN INJECTION HAZARD
High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event
that injection occurs, get immediate surgical treatment.
•Do not aim the gun at, or spray any person or animal.
•Keep hands and other body parts away from the discharge. For example, do not try to stop leaks
with any part of the body.
•Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.
•Use Graco nozzle tips.
•Use caution when cleaning and changing nozzle tips. In the case where the nozzle tip clogs while
spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure
before removing the nozzle tip to clean.
•Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn
off the unit and follow the Pressure Relief Procedure for turning off the unit.
•Check hoses and parts for signs of damage. Replace any damaged hoses or parts.
•This system is capable of producing 3300 psi (227 bar, 22.7 MPa). Use Graco replacement parts or
accessories that are rated a minimum of 3300 psi (227 bar, 22.7 MPa).
•Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.
•Verify that all connections are secure before operating the unit.
•Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls.
WARNING
Warnings
332916C 7
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•Always wear appropriate gloves, eye protection, and a respirator or mask when painting.
•Do not operate or spray near children. Keep children away from equipment at all times.
•Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.
•Stay alert and watch what you are doing.
•Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn
off the unit and follow the Pressure Relief Procedure for turning off the unit.
•Do not operate the unit when fatigued or under the influence of drugs or alcohol.
•Do not kink or over-bend the hose.
•Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.
•Do not use the hose as a strength member to pull or lift the equipment.
•Do not spray with a hose shorter than 25 feet.
•Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.
•Make sure all equipment is rated and approved for the environment in which you are using it.
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-
tric shock.
•Turn off and disconnect power cord before servicing equipment.
•Connect only to grounded electrical outlets.
•Use only 3-wire extension cords.
•Ensure ground prongs are intact on power and extension cords.
•Do not expose to rain. Store indoors.
•Wait five minutes after disconnecting power cord before servicing large capacitor units.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or prop-
erty damage.
•Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents.
•Many other fluids may contain chemicals that can react with aluminum. Contact your material sup-
plier for compatibility.
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate fingers and other body parts.
•Keep clear of moving parts.
•Do not operate equipment with protective guards or covers removed.
•Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure and disconnect all power sources.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including
eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is
not limited to:
•Protective eyewear, and hearing protection.
•Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
WARNING
Component Identification
8332916C
Component Identification
695 / 795 / 1095 / 1595 / Mark IV / Mark V / Mark VII / Mark X
Standard Models:
ONOFF
ti14839c
A
GH J K
L
B
C
D
E
F
M
A Pressure Gauge (not available on all units)
B Amp Switch (not available on all units)
C ON/OFF Switch
D Pressure Control
E Prime / Spray Valve
F Trigger Lock
GFilter
H Strainer
JPump
K Drain Tube
L Model/Serial Tag
M ProGuard Status Light
Component Identification
332916C 9
695 / 795 / 1095 / 1595 Mark IV / Mark V / Mark VII / Mark X
ProContractor Models:
ONOFF
ti18239b
P
N
M
L
G
A
B
R
K
J
H
C
D
E
FF
A Smart Control 3.0 Display
B Amp Switch (not available on all units)
C ON/OFF Switch
D Pressure Control
E Spray / Prime / Fast Flush
F Trigger Lock
GFilter
H Strainer
JPump
KProConnect
™
II
LTool Box
M Rod Pull Feature
N Unit / Serial Tag
P Drain Tube
RQuikReel
Component Identification
10 332916C
1095 / 1595 / Mark V IronMan Models:
ONOFF
ti22935a
N
M
L
G
A
B
K
J
H
C
D
E
F
A Smart Control 3.0 Display
B Amp Switch (not available on all units)
C ON/OFF Switch
D Pressure Control
E Spray / Prime / Fast Flush
F Trigger Lock
GFilter
H Strainer
JPump
KProConnect
™
II
L Rod Pull Feature
M Unit / Serial Tag
N Drain Tube
Grounding
332916C 11
Grounding
The sprayer cord includes a grounding wire with an
appropriate grounding contact. Do not use the sprayer if
the electrical cord has a damaged ground contact.
The plug must be plugged into an outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify plug! If it will not fit in outlet, have
grounded outlet installed by a qualified electrician. Do
not use an adapter.
Power Requirements
•100-120V units require 100-120 VAC, 50/60 Hz,
15A, 1 phase
•230V units require 220-240 VAC, 50/60 Hz,
10A-16A
Extension Cords
Use an extension cord with an undamaged ground
contact.
If an extension cord is necessary, use a 3-wire, 12 AWG
(2.5 mm
2
) minimum. Longer cords and higher gauge
cords reduce sprayer performance.
The equipment must be grounded to reduce the risk
of static sparking and electric shock. Electric or static
sparking can cause fumes to ignite or explode.
Improper grounding can cause electric shock.
Grounding provides an escape wire for the electric
current.
ti7528b
ti7529b
10/16 Amp Switch
12 332916C
Pails
Solvent and oil/based fluids: follow local code. Use
only conductive metal pails, placed on a grounded sur-
face such as concrete.
Do not place pail on a nonconductive surface such as
paper or cardboard which interrupts grounding
continuity.
Grounding a metal pail: connect a ground wire to the
pail by clamping one end to pail and other end to a true
earth ground.
To maintain grounding continuity when flushing or
relieving pressure: hold metal part of spray gun firmly
to side of a grounded metal pail. Then trigger gun.
10/16 Amp Switch
(Mark VII and Mark X units)
Select 10A or 16A setting based on your circuit rating.
15/20 Amp Switch
(120V 1595 and Mark V units)
Select 15A or 20A setting based on your circuit rating.
ti5850b
ti14840a
ti18247b
ti22874a
ti22936a
Pressure Relief Procedure
332916C 13
Pressure Relief Procedure
Follow the Pressure Relief Procedure whenever
you see this symbol.
1. Turn power OFF. Wait 7 seconds for power to
dissipate.
2. Engage trigger lock.
3. Remove guard and SwitchTip.
4. Turn pressure to lowest setting. Trigger gun to
relieve pressure.
5. Put drain tube in pail. Turn prime valve down to
DRAIN position. Leave prime valve in DRAIN posi-
tion until you are ready to spray again.
6. If you suspect the spray tip or hose is clogged or
that pressure has not been fully relieved after follow-
ing the steps above, VERY SLOWLY loosen tip
guard retaining nut or hose end coupling to relieve
pressure gradually, then loosen completely. Clear
hose or tip obstruction.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury
from pressurized fluid, such as skin injection,
splashing fluid and moving parts, follow the Pressure
Relief Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
ti18199a
ti2769a
ti22937a
ti2595a
ti14842a
Setup
14 332916C
Setup
1. All sprayers except ProContractor: Connect
Graco airless hose to sprayer. Tighten securely.
If using the optional hopper, remove the nipple fit-
ting from the filter. Install 45° elbow (from parts box)
into filter and install nipple fitting into elbow. Then
connect the hose to the nipple.
NOTE: Make sure nipple fitting is angled away from
hopper so the hose can be easily installed.
2. Connect whip hose (if applicable) and gun to other
end of hose. Tighten securely.
3. Engage trigger lock.
4. Remove tip guard.
5. Check inlet strainer for clogs and debris.
6. Fill throat packing nut with Graco TSL to prevent
premature packing wear. Do this each time you
spray.
7. Turn power OFF.
8. Plug power supply cord into a properly grounded
electrical outlet.
9. Turn prime valve down to DRAIN position.
10. Place pump in grounded metal pail partially filled
with flushing fluid. Attach ground wire to pail and
to true earth ground. Perform steps 1 - 5 of Startup
to flush out storage oil shipped in sprayer. Use
water to flush water-base paint and mineral spirits to
flush oil-base paint and storage oil.
ti22875a
ti18631a
ti18195a
ti18199a
ti2769a
ti17608b
ti18421b
ti22950a
ti14842a
ti18245b
Startup
332916C 15
Startup
1. Perform Pressure Relief Procedure, page 13.
2. Turn pressure control to lowest pressure.
3. Turn power ON.
4. Increase pressure 1/2 turn to start motor and allow
fluid to circulate through drain tube for 15 seconds;
turn pressure down.
5. Turn prime valve forward to SPRAY position. Disen-
gage trigger lock.
6. Hold gun against grounded metal flushing pail. Trig-
ger gun and increase fluid pressure 1/2 turn. Flush
1 minute.
7. Inspect for leaks. If leaks occur, perform Pressure
Relief Procedure, page 13. Tighten fittings. Per-
form Startup, steps 1 - 5. If no leaks, proceed to
step 7.
8. Place pump in paint pail.
9. Trigger gun again into flushing pail until paint
appears. Move gun to paint pail and trigger for 20
seconds.
10. Engage trigger lock. Assemble tip and guard, see
instructions on next page.
ti13670b
ti4266b
1/2
15sec.
ti14845a ti18198a
High-pressure spray is able to inject toxins into the
body and cause serious bodily injury. Do not stop
leaks with hand or rag.
ti22949a
ti18244b
ti18248a
ti18199a
Switch Tip Installation
16 332916C
Switch Tip Installation
1. Perform Pressure Relief Procedure, page 13.
2. Use spray tip (A) to insert OneSeal
™
(B) into
guard (C).
3. Insert Switch Tip.
4. Screw assembly onto gun. Tighten.
Spray
1. Spray test pattern. Increase pressure to eliminate
heavy edges. Use smaller tip size if pressure adjust-
ment can not eliminate heavy edges.
2. Hold gun perpendicular, 10-12 in. (25-30 cm) from
surface. Spray back and forth. Overlap by 50%.
Trigger gun after moving and release before stop-
ping.
Clearing Tip Clog
1. Release trigger, engage trigger lock. Rotate
SwitchTip. Disengage trigger lock. Trigger gun to
clear clog.
2. Engage trigger lock. Return SwitchTip to original
position. Disengage trigger lock and continue spray-
ing.
ti13023a
CA
B
ti13024a
ti2710a
SKIN INJECTION HAZARD
Never point gun at your hand or into a rag!
ti18243a
ti18242a
ti13033a
ti13034a
Fast Flush (ProContractor and IronMan models only)
332916C 17
Fast Flush
(ProContractor and IronMan models only)
To flush the hose and gun at an accelerated speed, per-
form the following steps:
1. Perform steps 1 - 3 of Cleanup, page 22.
2. Squeeze gun trigger and turn prime valve down to
DRAIN position and then over to FAST FLUSH.
3. Continue flushing system until fluid appears clear.
WatchDog
™
Protection System
(ProContractor and IronMan models only)
Pump stops automatically when material pail is empty.
To Activate:
1. Perform Startup.
2. Turn WatchDog switch ON and WD ON displays.
EMPTY displays/flashes and pump stops when
Watchdog protection system detects an empty
material pail.
3. Turn WatchDog switch OFF. Add material or rep-
rime sprayer. Turn pump switch OFF and ON to
reset WatchDog protection system. Turn WatchDog
switch back ON to continue to monitor material
level.
ti22940a
ti22938a
ti22033a
ti22939a
ProGuard
18 332916C
ProGuard
This sprayer protects itself against high and low voltage.
If the sprayer is plugged into a power source that is too
low or too high the sprayer will stop operating.
Standard Models
Standard models come equipped with a ProGuard sta-
tus indicator light. This light has three different states of
operation: ON, blink, and OFF.
See Troubleshooting (page 24) to determine the cause
of any errors.
ProContractor and IronMan Models
One of three error codes will be displayed:
Error
Code Definition
Light is ON
Unit is powered and operating normally.
Light is Blinking
Voltage supply is too low or too high for
sprayer and will not run until it is plugged
into a good power supply.
Light is OFF
No power to sprayer, or there is another
error other than the voltage supply.
ProGuard
Status Indicator Light
Error
Code Definition
Multiple incoming voltage surges
detected - unplug sprayer and
locate good voltage supply to
prevent damage to electronics.
Typical cause of this error is plugging
into a circuit that is higher than the
rated voltage of the sprayer. Find a
circuit that supplies the correct
voltage.
Incoming voltage too low for
sprayer operation - unplug sprayer
and locate good voltage supply to
prevent damage to electronics.
Typical cause of this error is other
equipment on the same circuit or
generator frequently turning on/off
under load. Find a circuit that is
dedicated to the sprayer.
Sprayer plugged into wrong
voltage - unplug sprayer and
locate correct voltage supply.
Typical cause of this error is a GFCI
box that is wired for the wrong
voltage (240V vs. 120V). No damage
has occurred to the sprayer. Find a
circuit with the correct voltage and
the sprayer will run correctly.
Hose Reel
332916C 19
Hose Reel
(ProContractor models only)
1. Make sure hose is routed through hose guide.
2. Lift and turn pivot lock 90° to unlock hose reel. Pull
on hose to remove it from hose reel.
3. Pull reel handle up and turn clockwise to reel in
hose.
NOTE: The hose reel can be locked into two positions:
Usage (A) and Storage (B).
Moving parts can pinch, cut or amputate fingers and
other body parts. To avoid injury from moving parts, be
sure to keep your head clear of hose reel while winding
up hose.
ti18241a
ti13501c
ti13503b ti13502b
(A) (B)
ti13563b
Digital Tracking System (ProContractor and IronMan models only)
20 332916C
Digital Tracking System
(ProContractor and IronMan models only)
Operation Main Menu
Short press to move to next display. Press and hold (5
seconds) to change units or reset data.
1. Turn pressure to lowest setting. Trigger gun to
relieve pressure. Turn prime valve down to DRAIN
position.
2. Turn power ON. Pressure display appears. Dashes
will not appear unless pressure is less than 200 psi
(14 bar, 1,4 MPa).
Change Display Units
Press and hold DTS button for 5 seconds to change
pressure units (psi, bar, MPa) to desired units. Selec-
tion of bar or MPa changes gallons to liters x 10. To
change display units DTS must be in pressure display
mode and pressure must be at zero.
Job Gallons
1. Short press DTS button to move to Job Gallons (or
liters x 10).
NOTE: JOB scrolls past, then the number of gallons
sprayed above 400 psi (28 bar, 2.8 MPa) for Mark
VII and Mark X displays; 1000 psi (70 bar, 7 MPa)
for all other models.
2. Press and hold to reset to zero.
Lifetime Gallons
1. Short press DTS button to move to Lifetime Gallons
(or liters x 10).
NOTE: LIFE scrolls briefly, then the number of gal-
lons sprayed above 400 psi (28 bar, 2.8 MPa) for
Mark VII and Mark X displays; 1000 psi (70 bar, 7
MPa) for all other models.
ti22719a
ti22941a
ti22942a
ti22876a
ti22717a
ti22718a
Digital Tracking System (ProContractor and IronMan models only)
332916C 21
Secondary Menu - Stored Data
1. Perform Pressure Relief, steps 1 - 4 if they have not
already been done.
2. Turn power switch on while holding DTS button down.
3. SERIAL NUMBER scrolls past and then serial number
(e.g. 00001) displays.
4. Short press DTS button and MOTOR HOURS scrolls past
and then total motor run hours are displayed.
5. Short press DTS button. LAST CODE scrolls by and last
code is displayed; e.g. E=07 (see Repair manual).
6. Press and hold DTS button to clear code to zero.
7. Short press DTS button. W-DOG scrolls past then OFF
displays if watchdog switch is OFF. ON displays if Watch-
dog switch is ON.
8. Press and hold (8 seconds) DTS button to move to
WatchDog Trigger % menu. Continue to hold DTS button
and Watchdog can be set to trigger at 30, 40, 50, or 60%
of current sprayer pressure setting. Release DTS button
when desired % is displayed. Default is 50%.
9. Short press to move to SOFTWARE REV.
10. Short press DTS button. MOTOR ID RESISTOR scrolls
by and model code number (see below).
ti22881a
ti22720a
ti22721a
ti22722a
ti22723a
Motor ID Number Models
0695
2 795 / Mark IV
4 1095 / 230V Mark V
6 1595 / 120V Mark V / MARK VII
10 Mark X
ti22724a
ti22725a
Cleanup
22 332916C
Cleanup
1. Perform Pressure Relief Procedure (page 13),
steps 1 - 4. Remove tip guard from gun.
NOTE: Use water for water-base material, mineral
spirits for oil-base material, or other solvents recom-
mended by manufacturer.
2. Turn power ON. Turn prime valve forward to
SPRAY position.
3. Increase pressure to 1/2. Hold gun against pail. Dis-
engage trigger lock. Trigger gun until flushing fluid
appears.
4. Move gun to waste pail, hold gun against pail, trig-
ger gun to thoroughly flush system. Release trigger
and engage trigger lock.
5. Turn prime valve down to DRAIN position and allow
flushing fluid to circulate until flushing fluid appears
clear.
6. Turn prime valve forward to SPRAY position. Trig-
ger gun into flushing pail to purge fluid from hose.
7. Raise pump above flushing fluid and run sprayer for
15 to 30 seconds to drain fluid. Turn power OFF.
8. Turn prime valve down DRAIN position. Unplug
sprayer.
ti22943a
ti18249a
ti22944a
ti18248a
ti22945a
ti22946a
ti18248a
ti22947a
ti22945a
Cleanup
332916C 23
9. Remove filters from gun and sprayer, if installed.
Clean and inspect. Install filters.
10. If flushing with water, flush again with mineral spir-
its, or Pump Armor, to leave a protective coating to
prevent freezing or corrosion.
11. Wipe sprayer, hose and gun with a rag soaked in
water or mineral spirits.
ti13454a ti15018a
ti2895a
Pump Armor
ti2776a
Troubleshooting
24 332916C
Troubleshooting
Mechanical/Fluid Flow
Perform Pressure Relief Procedure; page 13.
TYPE OF PROBLEM
WHAT TO CHECK
If check is OK, go to next check
WHAT TO DO
When check is not OK, refer to this column
For units with display:
CODE XX is displayed.
For units with no display:
ProGuard status light is
blinking or the light is off
and there is power to the
sprayer.
Fault condition exists Determine fault correction from table,
page 27.
Pump output is low Spray tip worn Follow Pressure Relief Procedure on page
13, then replace tip. See your separate gun or
tip manual.
Spray tip clogged Relieve pressure. Check and clean spray tip.
Paint supply Refill and reprime pump.
Intake strainer clogged Remove and clean, then reinstall
Intake valve ball and piston ball are
not seating properly
Remove intake valve and clean. Check balls
and seats for nicks; replace if necessary; see
pump manual. Strain paint before using to
remove particles that could clog pump.
Fluid filter, tip filter, or tip is clogged
or dirty.
Clean filter; see operation manual.
Prime valve leaking Relieve pressure. Repair prime valve.
Verify pump does not continue to
stroke when gun trigger is released.
(Prime valve not leaking.)
Service pump; see pump manual.
Leaking around throat packing nut
which may indicate worn or damaged
packings.
Replace packings; see pump manual. Also
check piston valve seat for hardened paint or
nicks and replace if necessary. Tighten pack-
ing nut/wet-cup.
Troubleshooting
332916C 25
Pump output is low Pump rod damage Repair pump. See pump manual.
Low stall pressure Turn pressure knob fully clockwise. Make sure
pressure control knob is properly installed to
allow full clockwise position. If problem per-
sists, replace pressure transducer.
Piston packings are worn or dam-
aged
Replace packings; see pump manual.
O-ring in pump is worn or damaged Replace o-ring; see pump manual.
Intake valve ball is packed with mate-
rial
Clean intake valve; see pump manual.
Pressure setting is too low Increase pressure; see pump manual.
Large pressure drop in hose with
heavy materials
Use larger diameter hose and/or reduce overall
length of hose.
Check to see if Amp switch (10/16 or
15/20) is on low setting. Make sure
circuit is able to provide high setting.
Switch to 16A or 20A setting. Change to circuit
that provides 16A or 20A. Change to less
loaded circuit.
Motor runs but pump does
not stroke
Displacement pump pin damaged or
missing; see pump manual.
Replace pump pin if missing. Be sure retainer
spring is fully in groove all around connecting
rod; see pump manual.
Connecting rod assembly damaged;
see pump manual.
Replace connecting rod assembly; see pump
manual.
Gears or drive housing damaged. Inspect drive housing assembly and gears for
damage and replace if necessary; see pump
manual.
Excessive paint leakage
into throat packing nut
Throat packing nut is loose Remove throat packing nut spacer. Tighten
throat packing nut just enough to stop leakage.
Throat packings are worn or dam-
aged
Replace packings; see pump manual.
Displacement rod is worn or dam-
aged
Replace rod; see pump manual.
Fluid is spitting from gun Air in pump or hose Check and tighten all fluid connections. Cycle
pump as slowly as possible during priming.
Tip is partially clogged Clear tip; see Operation manual.
Fluid supply is low or empty Refill fluid supply. Prime pump; see pump man-
ual. Check fluid supply often to prevent running
pump dry.
TYPE OF PROBLEM
WHAT TO CHECK
If check is OK, go to next check
WHAT TO DO
When check is not OK, refer to this column
Troubleshooting
26 332916C
Pump is difficult to prime Air in pump or hose Check and tighten all fluid connections. Cycle
pump as slowly as possible during priming.
Intake valve is leaking Clean intake valve. Be sure ball seat is not
nicked or worn and that ball seats well. Reas-
semble valve.
Pump packings are worn Replace pump packings; see pump manual.
Paint is too thick Thin the paint according to supplier recommen-
dations.
No display, sprayer
operates
Display is damaged or has bad con-
nection
Check connections. Replace display.
TYPE OF PROBLEM
WHAT TO CHECK
If check is OK, go to next check
WHAT TO DO
When check is not OK, refer to this column
Troubleshooting
332916C 27
Electrical
Symptom: Sprayer does not run, stops running, or will
not shut off.
Perform Pressure Relief Procedure; page 13.
1. Plug sprayer into correct voltage, grounded outlet.
2. Set power switch OFF for 30 seconds and then ON
again (this ensures sprayer is in normal run mode).
3. Turn pressure control knob clockwise 1/2 turn.
4. View digital displayy.
For units without a display, see
ProGuard
(page 18). If
there is a voltage supply issue (CODE 04, 08, or 17), the
ProGuard status light will blink continuously when the
ON/OFF switch is ON. To determine which code (or any
other code besides voltage supply) refer to the control
board status light. Turn the ON/OFF switch OFF, remove
the control cover then turn power back ON. Observe the
status light. Blinking LED total count equals the error
code (for example: two blinks equals CODE 02).
Keep clear of electrical and moving parts during trou-
bleshooting procedures. To avoid electrical shock haz-
ards when covers are removed for troubleshooting, wait
5 minutes after unplugging power cord for stored elec-
tricity to dissipate.
D20
D20
ProGuard Status Light Control Board Status Light
TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK
Sprayer does not run at all See flow chart, page 33.
Display is blank
ProGuard status light and
control board status light never
light
Sprayer does not run at all Check transducer or transducer
connections
1. Make sure there is no pressure in the system (see
Pressure Relief Procedure, page
13
). Check fluid
path for clogs, such as clogged filter.
2. Use airless paint spray hose with no metal braid
1/4 in. x 50 ft minimum. Smaller hose or metal braid
hose may result in high-pressure spikes.
3. Set sprayer to OFF and disconnect power to
sprayer.
4. Check transducer and connections to control board.
5. Disconnect transducer from control board socket.
Check that transducer and control board contacts
are clean and secure.
6. Reconnect transducer to control board socket.
Connect power, set sprayer ON and control knob
1/2 turn clockwise. If sprayer does not run properly,
set sprayer to OFF and go to next step.
7. Install new transducer. Connect power, set sprayer
ON and control knob 1/2 turn clockwise. Replace
control board if sprayer does not run properly.
Display shows CODE 02
Control board status light blinks
2 times repeatedly
Troubleshooting
28 332916C
Sprayer does not run at all Check transducer or transducer
connections (control board is not
detecting a pressure signal).
1. Set sprayer to OFF and disconnect power to
sprayer.
2. Check transducer and connections to control board.
3. Disconnect transducer from control board socket.
Check to see if transducer and control board
contacts are clean and secure.
4. Reconnect transducer to control board socket.
Connect power, set sprayer ON and control knob
to 1/2 turn clockwise. If sprayer does not run,
set sprayer to OFF and go to next step.
5. Connect a confirmed working transducer to control
board socket.
6. Set sprayer ON and control knob to 1/2 turn
clockwise. If sprayer runs, install new transducer.
Replace control board if sprayer does not run.
7. Check transducer resistance with ohmmeter (less
than 9k ohm between red and black wires and 3-6k
ohm between green and yellow wires).
Display shows CODE 03
Control board status light blinks
3 times repeatedly
Sprayer does not run at all
Check voltage supply to the
sprayer (control board is
detecting a multiple voltage
surges).
1. Set sprayer to OFF and disconnect power to
sprayer.
2. Locate a good voltage supply to prevent damage to
electronics.
Display shows CODE 4
Control board status light blinks
four times repeatedly
TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK
Troubleshooting
332916C 29
Sprayer does not run at all Control is commanding motor to run
but motor shaft does not rotate.
Possibly locked rotor condition, an
open connection exists between
motor and control, there is a
problem with motor or control board,
or motor amp draw is excessive.
1. Remove pump and try to run sprayer. If motor runs,
check for locked or frozen pump or drive train.
If sprayer does not run, continue to step 2.
2. Set sprayer to OFF and disconnect power to
sprayer.
3. Disconnect motor connector(s) from control board
socket(s). Check that motor connector and control
board contacts are clean and secure. If contacts
are clean and secure, continue to step 4.
4. Set sprayer to OFF and spin motor fan 1/2 turn.
Restart sprayer. If sprayer runs, replace control
board. If sprayer does not run, continue to step 5.
5. Perform Spin Test: Test at large 4-pin motor field
connector. Disconnect fluid pump from sprayer. Test
motor by placing a jumper across pins 1 & 2. Rotate
motor fan at about 2 revolutions per second. A cogging
resistance to motion should be felt at the fan.
The motor should be replaced if no resistance is felt.
Repeat for pin combinations 1 & 3 and 2 & 3. Pin 4
(the green wire) is not used in this test. If all spin test
is positive, continue to step 6.
Display shows CODE 05
Control board status light blinks
5 times repeatedly
TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK
Green Blue Red Black
Green Blue Red Black
Green Blue Red Black
STEP 1:
STEP 2:
STEP 3:
Troubleshooting
30 332916C
Sprayer does not run at all Control is commanding motor to run
but motor shaft does not rotate.
Possibly locked rotor condition,
an open connection exists between
motor and control, there is a problem
with motor or control board, or
motor amp draw is excessive.
6. Perform Field Short Test: Test at large 4-pin motor
field connector. There should not be continuity from
pin 4, the ground wire, and any of the remaining
3 pins. If motor field connector tests fail,
replace motor.
7. Check Motor Thermal Switch: Unplug thermal
wires. Set meter to ohms. Meter should read the
proper resistance for each unit (see table below).
Display shows CODE 05
Control board status light blinks
5 times repeatedly
TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK
Resistance Table:
695/240V Mark IV 0 ohms
795/120V Mark IV 2k ohms
1095/240V Mark V 3.9k ohms
1595/120V Mark V/MARK VII 6.2k ohms
MARK X 10.0k ohms
-
ti13140a
Troubleshooting
332916C 31
Sprayer does not run at all Allow sprayer to cool. If sprayer
runs when cool, correct cause of
overheating. Keep sprayer in cooler
location with good ventilation. Make
sure motor air intake is not blocked.
If sprayer still does not run, follow
Step 1.
NOTE: Motor must be cooled down for the test.
1. Check thermal device connector (yellow wires)
at control board.
2. Disconnect thermal device connector from control
board socket. Make sure contacts are clean and
secure. Measure resistance of the thermal device. If
reading is not correct, replace motor.
Check Motor Thermal Switch: Unplug thermal
wires. Set meter to ohms. Meter should read the
proper resistance for each unit (see table below).
3. Reconnect thermal device connector to control
board socket. Connect power, turn sprayer ON and
control knob 1/2 turn clockwise. If sprayer does not
run, replace control board.
Display shows CODE 06
Control board status light blinks
6 times repeatedly
Sprayer does not run at all Check voltage supply to the sprayer
(incoming voltage too low for
sprayer operation)
1. Set sprayer to OFF and disconnect power to
sprayer.
2. Remove other equipment that uses the same circuit.
3. Locate a good voltage supply to avoid damage to
electronics.
Display shows CODE 08
Control board status light blinks
eight times repeatedly
Sprayer does not run at all Check to see if control board is over
heating.
1. Make sure motor air intake is not blocked.
2. Make sure fan has not failed.
3. Make sure control board is properly connected
to back plate and that conductive thermal paste
is used on power components.
4. Replace control board.
5. Replace motor.
Display shows CODE 10
Control board status light blinks
10 times repeatedly
TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK
-
ti13140a
Resistance Table:
695/240V Mark IV 0 ohms
795/120V Mark IV 2k ohms
1095/240V Mark V 3.9k ohms
1595/120V Mark V/MARK VII 6.2k ohms
MARK X 10.0k ohms
Troubleshooting
32 332916C
Sprayer does not run at all Excessive current protection
enabled
1. Cycle power on and off.
Display shows CODE 12
Control board status light blinks
12 times repeatedly
Sprayer does not run at all Check the connections above the
motor
1. Set sprayer to OFF and disconnect power to
sprayer.
2. Remove motor shroud.
3. Disconnect motor control and inspect for damage at
connectors.
4. Reconnect motor control.
5. Turn power on. If code continues, replace motor.
Display shows CODE 15
Control board status light blinks
15 times repeatedly
Sprayer does not run at all Check the connections. Control
is not receiving a motor position
sensor signal
1. Turn power OFF.
2. Disconnect motor position sensor and inspect for
damage at connectors.
3. Reconnect sensor.
4. Turn power ON. If code continues, replace motor.
Digital display shows CODE 16
Control board status light blinks
16 times repeatedly
Sprayer does not run at all Check voltage supply to the sprayer
(sprayer plugged into wrong
voltage)
1. Set sprayer to OFF and disconnect power to
sprayer.
2. Locate a good voltage supply to avoid damage to
electronics.
Display shows CODE 17
Control board status light blinks
17 times repeatedly
TYPE OF PROBLEM WHAT TO CHECK HOW TO CHECK
ti18685a
Troubleshooting
332916C 33
Sprayer Will Not Run
(See following page for steps)
Remove control box cover. Turn
sprayer ON. Observe control
board status light on control board
(see page 27).
No light
Once Normal operation
Light on
Continuously
Control board
commanding
motor to run
Flashing See Code section
for further
troubleshooting
Connect a test
transducer to the
board. Does the
motor run?
Replace
potentiometer.
See Step 3. Is the
proper reading
present through the
thermal switch
wires?
Replace the
ON/OFF switch.
See step 4. Does
the motor run?
See Step 1. Do
you have over
100 VAC
(220 VAC for
230V units)?
See Step 2. Do
you have over
100 VAC
(220 VAC for
230V units)?
Repair or
replace
power cord.
If motor is hot, let cool and
retest. If Step 3 still shows
incorrect resistance, replace
motor. The motor has
a defective thermal device.
Replace the
transducer
Replace the
control board.
YES
YES
YES
NO
NO
NO
NO
YES
YES
NO
Troubleshooting
34 332916C
-
V
--
200-240V
200-240V
100k ohm
STEP 1:
Plug power cord in
and turn switch ON.
Connect probes to
on/off switch. Turn
meter to AC Volts.
STEP 2:
Plug power cord in
and turn switch ON.
Connect probes to
on/off switch. Turn
meter to AC Volts.
STEP 3:
Check motor thermal switch.
Unplug yellow wires. Meter
should read according to
Resistance Table on page 30.
NOTE: Motor should be cool
during reading.
STEP 4:
Plug power cord
in and turn switch
ON. Disconnect
potentiometer.
Troubleshooting
332916C 35
Sprayer Will Not Shut Off
1. Perform Pressure Relief Procedure; page 13.
Leave prime valve open and power switch OFF.
2. Remove control box cover so the control board
status light can be viewed if available.
Troubleshooting Procedure
Plumb pressure gauge into paint
hose, plug sprayer in, and turn power
switch ON. Does sprayer reach or
exceed its maximum pressure?
Unplug the transducer from control
board. Does motor stop running?
Bad transducer. Replace and test
with a new one.
Replace the control board.
Mechanical problem: See the proper
fluid pump manual for the sprayer for
further trouble shooting procedures.
NO
NO
YES
YES
Technical Data
36 332916C
Technical Data
695 Sprayers
U.S. Metric
Sprayer
Maximum Delivery
North American Models 0.95 gpm 3.6 lpm
International Models 0.75 gpm 2.8 lpm
Maximum Tip Size 0.031 0.031
Fluid Outlet npsm 1/4 in. 1/4 in.
Cycles 226 per gallon 60 per liter
Generator Minimum 5000 W 5000 W
120V, A, Hz 14.8, 50/60 14.8, 8, 50/60
230V, A, Hz 9, 50/60 9, 50/60
Dimensions
Weight:
Standard Series Lo-Boy 94 lb 43 kg
Standard Series Hi-Boy 94 lb 43 kg
ProContractor 111 lb 50 kg
Height:
Standard Series Lo-Boy 27.5 in. 69.9 cm
Standard Series Hi-Boy 28.5 in. (Handle down)
38.75 in. (Handle up)
72.4 cm (Handle down)
98.4 cm (Handle up)
ProContractor 39 in. 99 cm
Length:
Standard Series Lo-Boy 37 in. 94 cm
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 29.5 in. 75 cm
Width: 22.5 in. 57.2 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
332916C 37
795 Sprayers
U.S. Metric
Sprayer
Maximum Delivery
North American Models 1.1 gpm 4.2 lpm
International Models 0.95 gpm 3.6 lpm
Maximum Tip Size 0.033 0.033
Fluid Outlet npsm 1/4 in. 1/4 in.
Cycles 195 per gallon 52 per liter
Generator Minimum 5000 W 5000 W
120V, A, Hz 15, 50/60 15, 50/60
230V, A, Hz 10, 50/60 10, 50/60
Dimensions
Weight:
Standard Series Lo-Boy 98 lb 45 kg
Standard Series Hi-Boy 98 lb 45 kg
ProContractor 115 lb 52 kg
Height:
Standard Series Lo-Boy 27.5 in. 69.9 cm
Standard Series Hi-Boy 28.5 in. (Handle down)
38.75 in. (Handle up)
72.4 cm (Handle down)
98.4 cm (Handle up)
ProContractor 39 in. 99 cm
Length:
Standard Series Lo-Boy 37 in. 94 cm
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 29.5 in. 75 cm
Width: 22.5 in. 57.2 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
38 332916C
1095 Sprayers
U.S. Metric
Sprayer
Maximum Delivery
North American Models 1.2 gpm 4.5 lpm
International Models 1.1 gpm 4.1 lpm
Maximum Tip Size 0.035 0.035
Fluid Outlet npsm 1/4 in. 1/4 in.
Cycles 123 per gallon 33 per liter
Generator Minimum 5000 W 5000 W
120V, A, Hz 15, 50/60 15, 50/60
230V, A, Hz 10, 50/60 10, 50/60
Dimensions
Weight:
Standard Series Hi-Boy 120 lb 55 kg
ProContractor 141 lb 64 kg
IronMan 127 lb 58 kg
Height:
Standard Series Hi-Boy 29.5 in. (Handle down)
38.5 in. (Handle up)
74.9 cm (Handle down)
97.8 cm (Handle up)
ProContractor 39 in. 99 cm
IronMan 40.2 in. 102 cm
Length:
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 28 in. 71 cm
IronMan 29.9 in. 76 cm
Width:
Standard Series Hi-Boy 24 in. 61 cm
ProContractor 24 in. 61 cm
IronMan 24.4 in. 62 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
332916C 39
1595 Sprayers
U.S. Metric
Sprayer
Maximum Delivery 1.35 gpm 5.1 lpm
Maximum Tip Size 0.039 0.039
Fluid Outlet npsm 1/4 in. 1/4 in.
Cycles 110 per gallon 29 per liter
Generator Minimum 5000 W 5000 W
120V, A, Hz 20/15, 50/60 20/15, 50/60
Dimensions
Weight:
Standard Series Hi-Boy 125 lb 57 kg
ProContractor 146 lb 66 kg
IronMan 132 lb 60 kg
Height:
Standard Series Hi-Boy 29.5 in. (Handle down)
38.5 in. (Handle up)
74.9 cm (Handle down)
97.8 cm (Handle up)
ProContractor 39 in. 99 cm
IronMan 40.2 in. 102 cm
Length:
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 28 in. 71 cm
IronMan 29.9 in. 76 cm
Width:
Standard Series Hi-Boy 24 in. 61 cm
ProContractor 24 in. 61 cm
IronMan 24.4 in. 62 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
40 332916C
Mark IV Sprayers
U.S. Metric
Sprayer
Maximum Delivery
North American Models 1.1 gpm 4.2 lpm
International Models 0.95 gpm 3.6 lpm
Maximum Tip Size
North American Models 0.033 0.033
International Models 0.031 0.031
Fluid Outlet npsm 3/8 in. 3/8 in.
Cycles 195 per gallon 52 per liter
Generator Minimum 5000 W 5000 W
120V, A, Hz 15, 50/60 15, 50/60
230V, A, Hz 10, 50/60 10, 50/60
Dimensions
Weight:
Standard Series Hi-Boy 98 lb 45 kg
ProContractor 119 lb 54 kg
Height:
Standard Series Hi-Boy 28.5 in. (Handle down)
38.75 in. (Handle up)
72.4 cm (Handle down)
98.4 cm (Handle up)
ProContractor 39 in. 99 cm
Length:
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 29.5 in. 75 cm
Width: 22.5 in. 57.2 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
332916C 41
Mark V Sprayers
U.S. Metric
Sprayer
Maximum Delivery
North American and UK Models 1.35 gpm 5.1 lpm
International Models 1.2 gpm 4.5 lpm
Maximum Tip Size
North American and UK Models 0.039 0.039
International Models 0.035 0.035
Fluid Outlet npsm 3/8 in. 3/8 in.
Cycles 110 per gallon 29 per liter
Generator Minimum 5000 W 5000 W
120V, A, Hz 20/15, 50/60 20/15, 50/60
230V, A, Hz 10, 50/60 10, 50/60
Dimensions
Weight:
Standard Series Hi-Boy 130 lb 59 kg
ProContractor 151 lb 68 kg
IronMan 137 lb 62 kg
Height:
Standard Series Hi-Boy 29.5 in. (Handle down)
38.5 in. (Handle up)
74.9 cm (Handle down)
97.8 cm (Handle up)
ProContractor 39 in. 99 cm
IronMan 40.2 in. 102 cm
Length:
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 28 in. 71 cm
IronMan 29.9 in. 76 cm
Width:
Standard Series Hi-Boy 24 in. 61 cm
ProContractor 24 in. 61 cm
IronMan 24.4 in. 62 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
42 332916C
Mark VII Sprayers
U.S. Metric
Sprayer
Maximum Delivery 1.58 gpm 6.0 lpm
Maximum Tip Size 0.041 in. 0.041 in.
Fluid Outlet npsm 1/2 in. 1/2 in.
Cycles 97 per gallon 26 per liter
Generator Minimum 5000 W 5000 W
230V, A, Hz 16, 50/60 16, 50/60
Dimensions
Weight:
Standard Series Hi-Boy 139 lb 63 kg
ProContractor 160 lb 73 kg
Height:
Standard Series Hi-Boy 29.5 in. (Handle down)
38.5 in. (Handle up)
74.9 cm (Handle down)
97.8 cm (Handle up)
ProContractor 39 in. 99 cm
Length:
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 28 in. 71 cm
Width: 24 in. 61 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
Technical Data
332916C 43
Mark X Sprayers
U.S. Metric
Sprayer
Maximum Delivery 2.1 gpm 8.0 lpm
Maximum Tip Size 0.045 in. 0.045 in.
Fluid Outlet npsm 1/2 in. 1/2 in.
Cycles 70 per gallon 19 per liter
Generator Minimum 5000 W 5000 W
230V, A, Hz 16, 50/60
Dimensions
Weight:
Standard Series Hi-Boy 154 lb 70 kg
ProContractor 178 lb 81 kg
Height:
Standard Series Hi-Boy 29.9 in. (Handle down)
40.1 in. (Handle up)
76 cm (Handle down)
102 cm (Handle up)
ProContractor 39 in. 99 cm
Length:
Standard Series Hi-Boy 26 in. 66 cm
ProContractor 30 in. 75 cm
Width: 24 in. 61 cm
Wetted parts zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal,
leather, UHMWPE, aluminum, tungsten carbide, PEEK, brass
Noise Level:
Sound Power 91 dBa* 91 dBa*
Sound Pressure 82 dBa* 82 dBa*
*per ISO 3744; measured at 3.1 ft *per ISO 3744; measured at 1 m
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 332916
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision C - March 2014
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
