Graco 333182A G40 Air Assisted Spray Gun Parts Users Manual Gun, Instructions, Parts, English

2015-04-02

: Graco Graco-333182A-G40-Air-Assisted-Spray-Gun-Parts-Users-Manual-685931 graco-333182a-g40-air-assisted-spray-gun-parts-users-manual-685931 graco pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

Instructions

333182A

G40 Air Assisted Spray Gun

For the application of architectural paints and coatings. For professional use only.
Model: 262929, 262932
Maximum Working Pressure: 4000 psi (280 bar, 28 MPa)
Maximum Air Working Pressure: 100 psi (7 bar, 0.7 MPa)

Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.

ti22688a

ti22689a

Warnings

Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The
exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.
When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this
manual where applicable.

WARNING
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Do not spray without tip guard and trigger guard installed.
• Engage trigger lock when not spraying.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or
servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are
antistatic or conductive.
• Stop operation immediately if static sparking occurs or you feel a shock. Do not use equipment until
you identify and correct the problem.
• Keep a working fire extinguisher in the work area.

333182A

Warnings

WARNING
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about
your material, request MSDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.
• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier
for compatibility.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye
injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is not limited to:
• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
CALIFORNIA PROPOSITION 65
This product contains a chemical known to the State of California to cause cancer, birth defects or other
reproductive harm. Wash hands after handling.

333182A

Component Identification

Component Identification
Ref.
A
B
C
D
E
F
G
H

Description
Trigger Lock
Spray Tip
Safety RAC Guard
Trigger
Filter/Filter Housing
Air Hose Connection
Air Adjustment Valve
Fluid Hose Connection

G
C

B
D

333182A

Component Identification

Pressure Relief Procedure

Connect Gun to Sprayer

Follow the Pressure Relief Procedure whenever you
see this symbol.

Attach fluid hose to inlet fitting (25)
on gun.

25
ti22554a

This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing fluid and
moving parts, follow the Pressure Relief Procedure when
you stop spraying and before cleaning, checking, or
servicing the equipment.
1.
2.

Lock trigger. Turn OFF power and turn pressure control to
lowest pressure setting.
Unlock trigger. Hold gun against side of flushing pail.
Trigger gun into pail to relieve pressure.

NOTE: The first time you set up
the gun for spraying you will have to cut 17
the translucent red air hose to length
desired.
For Air-Assisted spraying, attach air
a
supply hose (a) to gun air inlet fitting (17).

Attach other end of air and fluid supply hoses to sprayer.
Use two wrenches to tighten all connections securely (see
sprayer setup instructions in sprayer operation manual).

Installing Tip (33) and Guard (6) on Gun

If you suspect spray tip or hose is clogged or that pressure has
not been fully relieved after following the steps above, VERY
SLOWLY loosen tip guard retaining nut or hose end coupling
to relieve pressure gradually, then loosen completely. Clear
hose or tip obstruction.

Gun Trigger Lock

2.
3.
4.

To prevent injury when the gun is not in use, always lock the
trigger if unit is being shut down or left unattended.
Trigger Unlocked
(spray)

Trigger Locked
(no spray)

If equipment has recently been operated, Relieve
Pressure.
Insert seat housing (35)
35
6
into guard (6).
Insert tip (33).
33b
33a
Insert seal (33b) over seat
(35a) and insert in seat
33
housing (25). Use black
seal for water-based
materials and orange for
solvent and oil-based
materials.
Flat Tip
Install guard (6) over end 33
of gun. Hand tighten.

If you notice fluid leaking from front of gun, replace the
seat (33a) and/or retighten the guard nut.
ti6581a

ti6582a

Setup

Make sure sprayer is turned off and unplugged from power
source and trigger lock is locked. Refer to your sprayer
instruction manual for priming and spray instructions.

Operation
NOTE: The following instructions are for guns used with
Graco’s FinishPro Sprayers. See the sprayer instruction
manual. If you are using a different sprayer, see your
equipment instruction manual.
When using a FinishPro II 295 model sprayer, air regulation is
only provided at the gun. The FinishPro II 395 and 595 model
sprayers provide additional air regulation at the sprayer.

1.
333182A

Unlock trigger (1a).
5

Component Identification

2.
3.

Be sure the arrow shaped tip (33) faces forward (spray).
Hold gun perpendicular and approximately 12-inches
(304 mm) from surface. Move gun first, then pull gun
trigger (3) to spray a test pattern.
Always hold gun at a right angle from the surface. Do not
make an arc with the gun. This causes an uneven coat of
fluid. To obtain an even finish, use smooth, even strokes
across the object being sprayed with a 50% overlap.

Note: If you are getting an irregular spray
pattern, clean air holes with solvent and
a soft brush or toothpick. Do not use
metal tools to clean the air cap holes as
this may scratch them. Scratches can
distort the spray pattern.

ti8792a

Maintenance

Clearing a Clog
Before performing any maintenance on gun, read all warnings
on front cover of this manual and relieve pressure, page 5.
1.
2.
3.
4.

Relieve pressure. Lock trigger (1a).
Flat Tip only: Remove and clean guard and tip.
Rotate tip (33) 180°. Unlock trigger (1a). Trigger gun into
pail or onto ground to remove clog.
Lock trigger (1a). Rotate tip (33) 180° back to spray
position.

Spraying
Refer to your Sprayer Instruction manual. The following
instructions are for guns used with Graco’s FinishPro
Sprayers.

Air-Assisted Spraying
1.
2.
3.
4.
5.

6.
7.
8.
9.

Set sprayer function selection switch to AIRLESS spraying.
Open gun air pressure regulator all the way.
Prime pump following priming instructions provided in
sprayer operation manual.
Turn sprayer fluid pressure control to highest setting.
Unlock trigger (1a). While triggering gun, turn down
sprayer fluid pressure until you notice tails forming in
spray pattern.
Stop triggering gun.
Set sprayer toggle switch to AA (Air Assisted) spraying.
Trigger gun. While spraying increase air pressure
regulator until tails disappear.
Use gun air regulator to fine tune spray pattern.

Airless Spraying
1.
2.
3.
4.

Set sprayer function selection switch to AIRLESS spraying.
Prime pump following priming instructions provided in
sprayer operation manual.
Start with sprayer pressure turned to lowest setting.
Spray a test pattern. Gradually increase sprayer pressure
until you achieve a consistent spray pattern, without
heavy edges. Use a smaller tip if pressure adjustment
alone does not eliminate edges.

Daily Maintenance
Flush gun after each work shift and store in a dry location.
Do not immerse the gun or any parts in water or cleaning
solvents.
•
Do not point gun up while cleaning it.
•
Do not wipe gun with cloth soaked in solvent; wring out
excess.
•
Solvent left in gun air passages could result in a poor
quality paint finish. Do not use any cleaning method that
may allow solvent into gun air passages.

Flushing and Cleaning

• Flush gun before changing colors, before storing and before
repairing gun.
• Flush at lowest possible pressure. Check connectors for
leaks and tighten as necessary.
• Flush with fluid that is compatible with fluid being dispensed
and equipment’s wetted parts.
1.
2.
3.
4.

Relieve pressure, page 5. Unplug sprayer from outlet.
Remove tip (33) and guard (6).
Disconnect air supply hose from gun.
Remove sprayer siphon tube set from paint and place in
flushing fluid. See Cleanup instructions in sprayer
operation manual 311905.
5. Plug sprayer in outlet. Set sprayer function selection
switch to AIRLESS.
6. Increase pressure slowly. Point gun down into a grounded
metal container. Pull gun trigger and flush gun with
solvent until all traces of fluid are removed from gun
passages.
7. Turn sprayer function selection switch to OFF.
8. Relieve pressure, page 5.
9. Disconnect fluid supply hose from gun.
10. If it is necessary to remove diffuser (5) to clean, trigger
gun while you remove the diffuser with the gun tool (30).
11. Dip the soft end of a soft-bristle brush into a compatible
solvent. Do not continuously soak the brush’s bristles
with solvent and do not use a wire brush.

333182A

Component Identification

12. With gun pointed down, clean front of the gun with the
soft-bristle brush and solvent.
13. Scrub the tip (33) and guard (6) with soft-bristle brush. To
clean out air cap holes, use a soft tool such as a
toothpick, to avoid damaging critical surfaces. Blow air
through the spray tip to ensure the orifice is clean.
14. If the diffuser (5) was removed, trigger the gun while you
reinstall the diffuser with the gun tool (30). Tighten the
diffuser securely to obtain a good seal. Torque to 155-165
in-lb (18-19 N.m). When properly tightened, the flange will
bottom out on the gun.
15. Install tip (33) and guard (6) on gun, page 5.
16. Using a soft cloth dampened in solvent, wipe off outside of
gun.
17. After cleaning, lubricate the
following parts weekly with
lubricant 111265.
• Trigger pivot pin (A)
• Both sides of gun where
trigger contacts gun (B)
• Fluid needle shaft, behind
trigger (C)

5.
6.

Needle Repair (2)
1.

Relieve pressure, page 5. Remove the diffuser (5), see
Seat Repair, page 7.

Remove the trigger pivot pin
nut (14), pivot pin (13), and
trigger (3) using the gun tool
(30) and nut driver (29).

14
C

ti8835a

Relieve pressure, page 5. Lock trigger (1a).
Unscrew fluid inlet fitting (25).
Remove inline fluid filter (24).
Clean filter with soft brush and compatible solvent.
Inspect filter and if damaged, replace it.
Install inline fluid filter (24) into base of fluid tube (16).
Screw fluid inlet fitting (25) into base of tube. Torque to
175-185 in-lb (20-21 N•m).

Repair

ti6574a

Seat Repair
Use Carbide Seat Repair Kit - 249456. For best results use all
new parts provided in kit.
1. Relieve the pressure, page 5. Remove the fluid and air
hoses from the gun.
2. Remove the guard (6) and spray tip (33).
3. Trigger gun to pull the needle housing off the seat while
you unscrew the diffuser (5) from the gun body (1), using
gun tool (30).
4. Inspect o-rings (5e, 5f, and 6a) in place. Carefully remove
the o-rings from the diffuser housing (5a) and replace if
necessary.
5. Remove the seat nut (5d), seat (5c) and seat gasket (5b)
using a 7/32 in. hex wrench.
6. Inspect seat (5c) and seat gasket (5b) and replace if
necessary.

Remove the fluid
2a
needle assembly
2
(2) from the front of
the gun by using
29
the nut driver tool
(29). If the needle
ti6575a
is bent or
damaged, or the
packing is worn or
leaking, replace the entire needle assembly. If
replacement is necessary, be sure to remove the o-ring
(2a) as it may stick inside the gun body.

Air Valve Repair (8)
1.

2.
3.

333182A

Reinstall the seat gasket (5b) seat (5c) and seat nut (5d).
Torque to 45-50 in-lb (5.0-5.6 N•m). Be sure not to
overtighten nut.
• When reinstalling the carbide seat (5c), the tapered end
of the seat must point toward the gun tip.

Cleaning/Replacing Filter (24)

1.
2.
3.
4.

Unscrew the spring cap (11) from the back of the gun
body (1) using the gun tool (30). Remove the two springs
(15 and 19), the shaft (9), and seat (10).
Push the air valve assembly (8) out the back of the gun.
Inspect the u-cup (7) in the gun body (1). If the u-cup is
worn or leaking, carefully remove the u-cup from the front
of the gun body, using a pick.
15
8
7

11
19
9
1
ti22776a

Component Identification

Fluid Tube Replacement (16)
1.

Remove the air inlet fitting
(17) using the gun tool (30)
and remove the screw (20).
Unscrew the fluid inlet fitting
(25). Remove and clean or
replace the inline fluid filter
(24).
Unscrew fluid tube connector
(16a) from fluid inlet. Carefully
remove gasket (22).

8.
75

Install the two springs (15 and 19). Screw the spring cap
(11) into the back of the gun body. Torque to 175-185
in-lb (20-21 N•m).
Lightly lubricate the needle assembly o-rings and shaft
where the packing slides. Be sure that the o-ring (2a) is in
place in the gun body (1).
Insert the fluid needle assembly (2) into the front of the
gun. Use the nut driver (29) to screw the fluid needle
assembly into the gun body (1) and torque to 50-60 in-lb
(6-7 N•m).

2a
ti22690a

Flat Tip Conversion Kit (Optional)
The Flat Tip Conversion Kit allows AAM Flat Tips to be used
with this gun. Order part number 288514.

ti6575a

Reassembly
1.

Install the tube gasket (22) in the gun. Hand tighten the
fluid tube connector (16a) into the gun’s fluid inlet. Antigens the air inlet fitting (17) and screw (20). Torque the
fluid tube connector to 150-160 in-lb (17-18 N•m). Torque
the air inlet fitting to 175-185 in-lb (20-21 N•m). Torque
the fluid tube bracket screw to 50-60 in-lb (6-7 N•m).
Install the inline fluid filter (24) into the base of the fluid
tube (16). Screw the fluid inlet fitting (25) into the base of
the tube. Torque to 175-185 in-lb (20-21 N•m).
Place the new u-cup (7) on the seal installation tool (28),
with the u-cup lips facing the tool. Push the u-cup into the
back of the gun until you feel a definite snap.

Lubricate lightly.

Lips face out of gun body.

7
28

ti6578a

Lubricate the front end of the air valve assembly (8).
Gently slide the air valve assembly into the back of the
gun, passing through the u-cup (7), as far as it will go. Be
careful not to damage the u-cup.
Slide the seat (10) onto the shaft (9). Be sure that the
tapered end of the seat is toward the thicker end of the
shaft. Carefully insert the shaft (9) and seat (10) in the air
valve (8).

Install the trigger (3), pivot pin (13), and nut (14). Use low
strength thread locker and be sure that the brass piece of
the fluid needle assembly (2) is behind the trigger.
Lubricate both sides of the pivot pin where the trigger
contacts the pin and lubricate the boss on both sides of
the gun where the trigger contacts the gun body. Torque
the nut to 20-30 in-lb (2-3 N•m).
10. Trigger the gun to pull the needle back while you screw
the diffuser assembly (5) into the gun body (1) using the
gun tool (30). Torque to 155-165 in-lb (18-19 N•m). When
properly tightened, the flange will bottom out on the gun.
11. Attach the guard (6) and spray tip (33), page 5.

Translated Manuals
Spanish - 333183

Estonian - 333195

French - 333184

Latvian - 333196

Dutch - 333185

Lithuanian - 333197

German - 333186

Polish - 333198

Italian - 333187

Hungarian - 333199

Turkish - 333188

Czech - 333200

Greek - 333189

Slovakian - 333201

Croatian - 333190

Portuguese - 333202

Danish - 333191

Finnish - 333203

Chinese - 333192

Swedish - 333204

Japanese - 333193

Norwegian - 333206

Korean - 333194

Russian - 333207

Translated manuals can be obtained from a distributor
or by visiting www.graco.com.

333182A

Parts (262929)

Parts (262929)
5a

5e 5b 5c 5d

33
6

2
ti22691a

1
22
75

29
30

3
14
16
24
25

28
Ref. Part
1
1a 249423
2
2a*
3
4
5
5a
5b
5c
5d
5e*
5f*
6
6a*
7*
8*
9
11
13
14
15
16
17
19

110004
249585
15G713
249877

111457
109450
288839
109213
188493
16A529
15F195
15F739
15F740
114069
249136
24U606
115141

333182A

Description
BODY, gun, assy
SAFETY, trigger
NEEDLE, assy; 3/32 carbide ball;
includes item 2a
PACKING, o-ring; PTFE
KIT, trigger, repair, includes 13 and 14
NUT, air plug
DIFFUSER, assy, RAC
DIFFUSER, housing
GASKET, seat; nylon
SEAT; carbide
NUT, seat
PACKING, o-ring, seat; PTFE
PACKING, o-ring; PTFE
GUARD, RAC
PACKING, o-ring, PTFE
PACKING, u-cup, gun; UHMWPE
VALVE, air, assy
SHAFT, fluid spring
CAP, spring
PIN, pivot
PIN, pivot, nut
SPRING, compression
TUBE, assy
VALVE, assy, inlet air
SPRING, compression

Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Ref. Part
20 16X404
22* 115133
24 224453
24a‡ 162863
25 15F186
28*
29 117642
30 15F446
31 222385
32 172479
33 FFT210
33a**
33b**
35† 15J770
75 156454

Description
FITTING, barbed
GASKET, tube, acetal
FILTER
GASKET, non-metallic (sold separately)
FITTING, fluid inlet
TOOL, installation; seal
TOOL, nut driver
TOOL, gun
CARD, warning (not shown)
TAG, warning (not shown)
SPRAY TIP
SEAT, gasket
SEAL
HOUSING, cylinder
O-RING

Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Replacement Danger and Warning labels, tags, and cards
are available at no cost.
 Included in Needle/Seat Repair Kit 255160 (purchase
separately)
† Included in RAC Guard Kit 288839
*Included in Seal Repair Kit 249422 (purchase separately)
‡ If you want to remove the filter, order 162863 to use as a
seal in its place.
**Included in 246453 RAC X One Seal Kit (Standard)
**Included in 248936 RAC X One Seal Kit (Solvent)

Parts (262932)

Parts (262932)
5f

5b 5c 5d

5a
5g
6b

6a
6

15
8
13

7
11

19
9
72

29
30

71
3

17
75
16

20
37

ti22692a

Ref.
1
2
2a
3
4
5
5a
5b
5c
5d
5e*
5f*
5g*
6
6a
6b
6c
7
8*
9
11
13
14
15
16
17

Part
110004
249585
249135
288192

111457
109450
111116
256721
249180
109213
15G320
188493
16A529
15F195
15F739
15F740
114069
249136
24U606

Description
BODY, gun
NEEDLE, assy, 3/32 carbide ball
O-RING
TRIGGER (includes 13, 14)
VALVE, fan control assy
DIFFUSER, assy, high pressure
DIFFUSER, housing
NYLON, gasket
CARBIDE, seat
NUT, seat
O-RING, PTFE
O-RING, PTFE
O-RING
AIRCAP, assembly, RAC conversion
AIRCAP, assembly
PACKING, o-ring
WASHER, PTFE, 1.2 OD
PACKING, u-cup, gun
VALVE, air, assembly
SHAFT, fluid spring
CAP, spring
PIN, pivot
PIN, pivot, nut
SPRING, compression
TUBE, assy
VALVE, assy, inlet air

Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Ref.
18
19
20
22
28
29
30
31
32
37
38
50
70
71
72
73
74
75

Part
115133
115141
16X404
AAM309
192282
117642
15F446
222385
172479
224453
15F186
017480
15F185
249423
115132
117517
15U104
156454

Description
GASKET, tube
SPRING, compression
FITTING, barbed
TIP, G15, G40
TOOL, installation, seal
TOOL, nut driver
TOOL, gun
TAG, warning (not shown)
TAG, warning (not shown)
FILTER, tip
FITTING, hose
ADHESIVE, thread locker
INSERT, fluid
STOP, trigger, molded
PIN, dowel
O-RING
TAG, important-tighten tip (not shown)
PACKING, o-ring

Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1

Replacement Danger and Warning labels, tags, and cards
are available at no cost.
 Included in Needle/Seat Repair Kit 255160
(purchase separately)
* Included in Seal Repair Kit 249422 (purchase separately)

333182A

Technical Data

Technical Data
G40 Air Assisted Airless Spray Gun
US

Metric

4 000 psi

28 MPa, 280 bars

Maximum Working Air Pressure

100 psi

0,7 MPa, 7 bars

Maximum Working Fluid Temperature

110°F

43°C

Maximum Working Fluid Pressure

Fluid inlet

1/4–18 npsm

Air Inlet

1/4-18 npsm

Gun Weight

16 oz

450 grams

Sound Pressure*: 20 psi (140 kPa, 1.4 bar)

66.9 dB(A)

Sound Pressure*: 100 psi (0.7 kPa, 7 bar)

80.0 dB(A)

Sound Power*: 20 psi (140 kPa, 1.4 bar)

76.8 dB(A)

Sound Power*: 100 psi (0.7 kPa, 7 bar)

89.9 dB(A)

Wetted Parts

Stainless Steel, Carbide, Ultra High Molecular Weight
Polyethylene, Acetal, PTFE, Nylon, Flouroelastomer

*All readings were taken with fan valve fully closed, (full fan size) at 20 psi (140 kPa, 1.4 bar) and 100 psi (0.7 kPa, 7
bar) and at the assumed operator position. Sound Power tested to ISO 9614-2.

333182A

Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance
of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 333182

Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision A - 2014

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Job Ref                         : C272X
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Marked                          : True
Copyright                       : 2014
Web Statement                   : 333182 - G40 Air Assisted Spray Gun, Instructions, Parts, English
Keywords                        : 333182, 333182A, 333182EN, 333182EN-A, G40 Air Assisted Spray Gun, Instructions, Parts, English, 262929, 262932
Create Date                     : 2004:10:18 09:44:46Z
Modify Date                     : 2014:04:01 11:52:38-05:00
Creator Tool                    : FrameMaker 9.0
Metadata Date                   : 2014:04:01 11:52:38-05:00
Format                          : application/pdf
Creator                         : Kaitlin Lueken
Description                     : G40 Air Assisted Spray Gun, Instructions, Instructions, Parts
Title                           : 333182A - G40 Air Assisted Spray Gun, Instructions, Parts, English
Subject                         : 333182, 333182A, 333182EN, 333182EN-A, G40 Air Assisted Spray Gun, Instructions, Parts, English, 262929, 262932
Document ID                     : uuid:25a45e3b-4662-4555-a5fc-f298466959be
Instance ID                     : uuid:3c2ff67c-91d7-44cf-b3d9-c71f6f5f8f79
Page Count                      : 12
Author                          : Kaitlin Lueken

EXIF Metadata provided by EXIF.tools

Graco 333182A G40 Air Assisted Spray Gun Parts Users Manual Gun, Instructions, Parts, English

Navigation menu

Versions of this User Manual:

Views

Navigation