Grand Wing Servo Tech GWT4GP24G Radio Control Transmitter User Manual T4GP cover page
Grand Wing Servo-Tech Co., Ltd. Radio Control Transmitter T4GP cover page
Contents
- 1. Manual Part 1
- 2. Manual Part 2
Manual Part 2
T4GP-2.4GHz INSTRUCTION MANUAL Receiver Installatlo For the trest of reception, when installing the receiver, please reler to the lollowmg instructions. 1 Keep the two antennas as stratght as possible, and should be placed at 180 degrees to each other Othentvlse It will reduce the eftecttve range 2 Keep the antennas away from conductive materials, such as metal and carbon by at least one inch. 3 Keep the antennas away from the motor \ ESC and other noise sources as much as possible 4 LED display a) Red light steady Receivtng signals. a Red light tlash - Poor signal reception ® Red light oft . No signal reception J Rudder Servo again CH, El ESC i l - _, . In: E. an E Allelon Servo A. \‘ Battery 1 Bind CM JL zSignaI/White or Orange 4. = Positive I Red _ = Negative / Black or Brown Elevator Servo Receiver Pro eIIer 180' p Bind Plug Each transmitter and receiver has a unique ID code, the receiver must be linked with the ID code of the transmltter wltl't which it is petng paired Elndlng is the process at programming the receiver to recogrize the ID code oi a single specific transmitter, so that the receiver will only 1isten to the information from its previously oound transmitter and ignores everything else (For Tl R set, the paired is already done at tactory.When you purchased another R-ASJhis procedure is necessary, otherwtse the receiver will not work) 1 Place the transmltter and recelver close to each other Wlthln one meter 2.With the power off, plug the hind plug into the BAT port. 3.Powel on the receiver by connecting the battery to any unused port. The red LED should be blinking. 4,Turn on the transmitter ( This procedure must be completed wlthtn 10 seconds after the receiver turn on J 5.When the binding is complete, the red LED in the receiver will change to steady. 6.Wlth the transmitter and the receiver power oil, remove the oind plug. 7 Please confirm that the receiver will now operate by your transmitter. Gmnd an System chlne,lnc Hualal Kali Vuanqu xteeang town, was 5 Brent circle City or Industry 125 De rung Road Sec 2 DongguanCtty Guangdong. china caewagauso usA rEL sets 769—87680000 FAX oeo 76937639555 E—rnall china@gws corn tw T4GP-2.4GHz INSTRUCTION MANUAL 7SERVO INSTAL Servo Arm Retaining Screw 7 lag—Tm’fsavo Arm l Horn Wood screw 4- RubberGrornmet 4-1 j H W Servo Eyelet - 3 .- '7 DEE- Servo Lead W / Connector Servo Case Servo Mount 8 TRAINER FUNCTION S The trainer runction is a very errective way for training students To use it, the special trainer cord (sold separately) is necessary 1 Match the servo reversing and trims at both radios 2 Turn on the power swttch or instructor transmitter, The student transmitter must be Iett oil, then plug the trainer cord into both transmitters, the student transmltter power Indlcatorwlll automatically turn on 3. When the trainer switch (instructor side) is not pressed, the instructor has control, when the trainer switch ls pressed, control ls transferred to the student AWarning: Never turn on the student transmitter power switch, it will cause interference and a crash, PRECAUTIO 1 Since the 2 AGHZ have dltterent Characterlstlcs than that of the conventional 27MHZ Bi 7ZMHZ frequencies Please keep the model in sight at all times as large objects can block the RF Signal, Please keep in mind that objects such as wire tences and Wire mesh WIII also cause loss of signal. z.The TAGP system is designed for micro electric—powered aircratt only it is imperative that the system not be used in larger aircraft that could exceed the range, 3. Always turn the transmitter on lirst, then the receiver. When you turn the system oft, always turn the receiver 0" first then transmitter. This step is very important always follow this procedure. Ifthis procedure is not tollowed, injury to yourself and others as well as loss of control could occur. ENS www, wccorrim wm Mus.com Gmnd tMng System u s A inc GWS Samoa Center Grand ang Servo—Tech Co ,Ltd 153 na rung Road Sec 2, us. cnth Taipei 22t. Taiwan rEt. assasssaszsstaee r FAX cums—5948051 FAX +6852436926545 FAX raaorzaoazomz or USA Inculrv saiss@gwsus cont Alter service servioe@gws can Iw messesezsm Atlerservlce service@gwsos com amine sales taioei@gwsoomtw International Inquiry exporl@gws com tw rtsr criih raipei 221 Taiwan TEL ‘1—909—5944979 TEL oasszreogzszss 4 .Manulaoturedtrycrandvnrig System Cltlrla, trio. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: 0 Reorient or relocate the receiving antenna, 0 Increase the separation between the equipment and receiver. 0 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 0 Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this deVice must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Fcc Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual, This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. PYINS-1150—----
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : 3.1-701 Modify Date : 2009:12:24 11:31:40+08:00 Create Date : 2009:12:24 11:31:35+08:00 Metadata Date : 2009:12:24 11:31:40+08:00 Creator Tool : PDFCreator Version 0.9.5 Format : application/pdf Title : T4GP cover page Creator : Salena Document ID : uuid:33cbf2b1-19a3-4495-b5aa-0fe6029a992e Instance ID : uuid:729dbf0a-8a15-40fb-878c-5bfa886fa08b Producer : GPL Ghostscript 8.61 Has XFA : No Page Count : 2 Author : SalenaEXIF Metadata provided by EXIF.tools