Grandstream Networks DP752 DECT Cordless VoIP Base Station User Manual

Grandstream Networks, Inc. DECT Cordless VoIP Base Station

User Manual

Download: Grandstream Networks DP752 DECT Cordless VoIP Base Station User Manual
Mirror Download [FCC.gov]Grandstream Networks DP752 DECT Cordless VoIP Base Station User Manual
Document ID4098190
Application IDzn8OxYmtYcVohIQX+bnBEw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize159.46kB (1993261 bits)
Date Submitted2018-12-07 00:00:00
Date Available2018-12-07 00:00:00
Creation Date2018-11-05 10:14:24
Producing SoftwareMicrosoft® Word for Office 365
Document Lastmod2018-12-07 09:24:06
Document TitleUser Manual
Document CreatorMicrosoft® Word for Office 365

Grandstream Networks, Inc.
DP752/DP730/DP722
DECT VoIP System
User Guide
DP752
DP730
DP722
DECT VoIP Base
DECT Cordless
DECT Cordless
Station
VoIP Phone
VoIP Phone
COPYRIGHT
©2018 Grandstream Networks, Inc. http://www.grandstream.com
All rights reserved. Information in this document is subject to change without notice. Reproduction or
transmittal of the entire or any part, in any form or by any means, electronic or print, for any purpose without
the express written permission of Grandstream Networks, Inc. is not permitted.
The latest electronic version of this user manual is available for download here:
http://www.grandstream.com/support
Grandstream is a registered trademark and Grandstream logo is trademark of Grandstream Networks, Inc.
in the United States, Europe and other countries.
CAUTION
Changes or modifications to this product not expressly approved by Grandstream, or operation of this product
in any way other than as detailed by this User Manual, could void your manufacturer warranty.
WARNING
Please do not use a different power adaptor with your devices as it may cause damage to the products and
void the manufacturer warranty.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 1
GNU GPL INFORMATION
DP752 firmware contains third-party software licensed under the GNU General Public License (GPL).
Grandstream uses software under the specific terms of the GPL. Please see the GNU General Public License
(GPL) for the exact terms and conditions of the license.
Grandstream GNU GPL related source code can be downloaded from Grandstream web site from:
http://www.grandstream.com/support/faq/gnu-general-public-license/gnu-gpl-information-download
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 2
Table of Content
DOCUMENT PURPOSE .................................................................................................... 9
CHANGE LOG ................................................................................................................. 10
Firmware Version 1.0.5.9 ........................................................................................................................ 10
GUI INTERFACE EXAMPLES ......................................................................................... 11
WELCOME ...................................................................................................................... 12
PRODUCT OVERVIEW ................................................................................................... 13
Feature Highlights ................................................................................................................................... 13
DP752 Technical Specifications .............................................................................................................. 14
DP730 Technical Specifications .............................................................................................................. 16
DP722 Technical Specifications .............................................................................................................. 18
GETTING STARTED ........................................................................................................ 20
Equipment Packaging ............................................................................................................................. 20
Connecting DP752 .................................................................................................................................. 22
Connecting via AC power ................................................................................................................ 22
Connecting via PoE ......................................................................................................................... 22
Setting up DP730/DP722 Handsets ....................................................................................................... 22
Battery Information .......................................................................................................................... 23
Setting up the Charge Station ................................................................................................................. 23
DP752 LED Patterns............................................................................................................................... 24
DP730/DP722 Handsets Description...................................................................................................... 24
DP730/DP722 Icons Description ............................................................................................................ 27
DP730/DP722 Handsets Menu ............................................................................................................... 29
BASIC OPERATIONS ...................................................................................................... 35
Turning the Handsets ON / OFF ............................................................................................................. 35
Setup Wizard .......................................................................................................................................... 35
Register DP730/DP722 Handsets to DP752 Base Station..................................................................... 35
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 3
Using DP730/DP722 with Multiple DP752 Base Stations ...................................................................... 36
Registering DP730/DP722 to an additional DP752 base station .................................................... 36
Switching Between Different Base Stations .................................................................................... 37
Unregister the DP730/DP722 ................................................................................................................. 37
Setting the Key Lock ............................................................................................................................... 38
Locating a DP730/DP722 Handset from DP752 Base station ............................................................... 39
Locate via DP752 Web UI ............................................................................................................... 39
Locate via DP752 Base station ....................................................................................................... 40
Checking System Status ......................................................................................................................... 40
Basic Network Settings ........................................................................................................................... 41
Change Menu and LCD Timeout ............................................................................................................ 42
Return to Idle Screen .............................................................................................................................. 42
Register SIP Account .............................................................................................................................. 42
Register Account via Web User Interface ........................................................................................ 42
PHONE SETTINGS.......................................................................................................... 45
Editing the Handset Name ...................................................................................................................... 45
Changing the Base PIN Code ................................................................................................................. 46
Selecting Phone Language ..................................................................................................................... 47
Activate/Deactivate Hands-Free Mode ................................................................................................... 48
Muting the Microphone ........................................................................................................................... 48
Adjusting Speaker and Earpiece Volume ............................................................................................... 48
Ringtones ................................................................................................................................................ 48
Setting the Ringer Volume on the Handsets ................................................................................... 48
Setting Ringtones on the Handsets ................................................................................................. 49
Advisory Tones ................................................................................................................................ 50
Ringtones Customization ................................................................................................................. 50
Date and Time......................................................................................................................................... 53
Gestures (DP730 only) ........................................................................................................................... 53
Facedown Hangup........................................................................................................................... 54
Close-to-Ear Backlight ..................................................................................................................... 54
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 4
Factory Functions ................................................................................................................................... 55
DP722/DP730 Handsets Firmware Upgrade .......................................................................................... 56
Reboot DP752 Base Station ................................................................................................................... 57
Reset DP722/DP730 Handsets .............................................................................................................. 57
CALL OPERATIONS ....................................................................................................... 59
Outgoing Default Line ............................................................................................................................. 59
Placing calls ............................................................................................................................................ 59
Make a Call using a Line ................................................................................................................. 59
Dialing from Call history ................................................................................................................... 60
Dialing from Phonebook .................................................................................................................. 61
Answering Calls ...................................................................................................................................... 61
Auto Answer..................................................................................................................................... 61
Off-Cradle Pickup ............................................................................................................................ 62
Ending Calls ............................................................................................................................................ 62
On-Cradle Hang-up ......................................................................................................................... 63
Rejecting Calls ........................................................................................................................................ 63
Direct IP Call ........................................................................................................................................... 63
Call Hold/Resume ................................................................................................................................... 64
Call Waiting ............................................................................................................................................. 64
Do Not Disturb ........................................................................................................................................ 65
Call Forward ............................................................................................................................................ 66
Call Transfer ............................................................................................................................................ 66
Blind Transfer ................................................................................................................................... 66
Attended Transfer ............................................................................................................................ 67
Speed Dial .............................................................................................................................................. 67
3-Way Conference .................................................................................................................................. 68
Voice Mail ................................................................................................................................................ 68
Set Voice Mail Feature Code ........................................................................................................... 68
Play Voice Mail Messages ............................................................................................................... 69
PTT (Push-To-Talk) Key for DP730 ........................................................................................................ 70
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 5
Call Features ........................................................................................................................................... 71
RESTORE FACTORY DEFAULT SETTINGS .................................................................. 72
EXPERIENCING DP752/DP722/DP730 .......................................................................... 73
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 6
Table of Tables
Table 1: DP752 Features at a Glance ............................................................................................................ 13
Table 2: DP730 Features at a Glance ............................................................................................................ 13
Table 3: DP722 Features at a Glance ............................................................................................................ 13
Table 4: DP752 Technical Specifications ....................................................................................................... 14
Table 5: DP730 Technical Specifications ....................................................................................................... 16
Table 6: DP722 Technical Specifications ....................................................................................................... 18
Table 7: Equipment Packaging – DP752 ....................................................................................................... 20
Table 8: Equipment Packaging – DP730 ....................................................................................................... 20
Table 9: Equipment Packaging – DP722 ....................................................................................................... 21
Table 10: DP722/DP730 Battery Specifications ............................................................................................. 23
Table 11: DP752 LED Patterns ...................................................................................................................... 24
Table 12: Keypad Keys Description ............................................................................................................... 25
Table 13: Keypad Keys Description ............................................................................................................... 26
Table 14: DP730/DP722 Icons Description .................................................................................................... 27
Table 15: DP752 Info description ................................................................................................................... 40
Table 16: DP722/DP730 Info description ....................................................................................................... 40
Table 17: Call Features .................................................................................................................................. 71
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 7
Table of Figures
Figure 1: DP752 Package Content ................................................................................................................ 20
Figure 2: DP730 Package Content ................................................................................................................ 21
Figure 3: DP722 Package Content ................................................................................................................ 21
Figure 4: DP752 Back View ........................................................................................................................... 22
Figure 5: Setting up the DP730/DP722 .......................................................................................................... 23
Figure 6: Setting up Charging Stations .......................................................................................................... 24
Figure 7: DP752 LED Patterns ...................................................................................................................... 24
Figure 8: DP722 Keys Description ................................................................................................................. 25
Figure 9: DP730 Keys Description ................................................................................................................. 26
Figure 10: DP730/DP722 Menu Structure ..................................................................................................... 30
Figure 11: Registration Process ..................................................................................................................... 36
Figure 12: Multiple Base Stations Registration .............................................................................................. 36
Figure 13: Switching Between Base Stations ................................................................................................ 37
Figure 14: Unregister DP730/DP722 from DP752 web UI ............................................................................. 38
Figure 15: Locate Handsets via Web UI ........................................................................................................ 39
Figure 16: Network Settings Configuration .................................................................................................... 41
Figure 17: SIP Settings .................................................................................................................................. 43
Figure 18: SIP Accounts Settings................................................................................................................... 44
Figure 19: Account Status .............................................................................................................................. 44
Figure 20: Handsets Name editing ................................................................................................................ 45
Figure 21: Edit Handsets Name from DP752................................................................................................. 46
Figure 22: Changing Admin Base PIN Code from DP722/DP730 ................................................................. 46
Figure 23: Changing Admin Base PIN Code from DP752 ............................................................................. 47
Figure 24: Handsets Language ...................................................................................................................... 47
Figure 25: Ringer Volume .............................................................................................................................. 49
Figure 26: Advisory Tone ................................................................................................................................ 50
Figure 27: Generating Custom Ringtone (Windows) ..................................................................................... 51
Figure 28: Downloading Custom Ringtones .................................................................................................. 52
Figure 29: Date and Time Settings ................................................................................................................ 53
Figure 30: DP730 Gestures ........................................................................................................................... 54
Figure 31: DP730 Gestures – Facedown Hangup ......................................................................................... 54
Figure 32: DP730 Gestures – Close-to-Ear Backlight ................................................................................... 54
Figure 33: Factory Functions ......................................................................................................................... 56
Figure 34: Firmware Notification .................................................................................................................... 56
Figure 35: Firmware Upgrade ........................................................................................................................ 57
Figure 36: Rebooting the Base Station .......................................................................................................... 57
Figure 37: Resetting the Base Station ........................................................................................................... 58
Figure 38: Outgoing Default Line ................................................................................................................... 59
Figure 39: PTT Feature Enabled.................................................................................................................... 70
Figure 40: PTT Transmission ......................................................................................................................... 70
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 8
DOCUMENT PURPOSE
This document describes the basic concept and tasks necessary to use and configure your DP722/DP730
via the LCD menu and also using the DP752 base station. And it covers the handsets installation, basic
operations and call features. Please visit http://www.grandstream.com/support to download the latest
“DP752/DP722/DP730 User Guide”.
This guide covers following topics:
•
Product Overview
•
Getting Started
•
Basic Operations
•
Phone settings
•
Call Operations
•
Restore Factory Default Settings
DP752/DP722/DP730 User Guide
Version 1.0.5.9
Page | 9
CHANGE LOG
This section documents significant changes from previous versions of user guide for DP752/DP722/DP730.
Only major new features or major document updates are listed here. Minor updates for corrections or editing
are not documented here.
Firmware Version 1.0.5.9
•
This is the initial version for DP752/DP730/DP722.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 10
GUI INTERFACE EXAMPLES
http://www.grandstream.com/sites/default/files/Resources/DP752_web_gui.zip
1.
Screenshot of Login Page
2.
Screenshots of Status Pages
3.
Screenshots of Profiles Pages
4.
Screenshots of DECT Pages
5.
Screenshots of Settings Pages
6.
Screenshots of Maintenance Pages
7.
Screenshots of Phonebook Pages
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 11
WELCOME
Thank you for purchasing Grandstream DP752 DECT IP Base Station and DP722/DP730 DECT Handsets.
The DP752 is a powerful DECT VoIP base station that pairs with up to 5 of Grandstream’s DP722/DP730
DECT handsets to offer mobility to business and residential users. It supports a range of 300 meters outdoors
and 50 meters indoors to give users the freedom to move around their work or home space, delivering efficient
flexibility. This DECT VoIP base station supports up to 10 SIP accounts and 5 concurrent calls while also
offering 3-way voice conferencing, full HD audio and integrated PoE. A shared SIP account on all handsets
will add seamless unified features that gives users the ability to answer all calls regardless of location in realtime. The DP752 supports a variety of auto-provisioning methods and TLS/SRTP/ HTTPS encryption security.
When paired with Grandstream’s DP722/DP730, the DP752 offers a powerful DECT VoIP base station that
allows any business or residential user to create a cordless VoIP solution.
The DP722/DP730 is a DECT cordless VoIP phone that allows users to mobilize their VoIP network
throughout any business, warehouse, retail store and residential environment. It is supported by
Grandstream’s DP752 DECT VoIP base station and delivers a combination of mobility and top-notch
telephony performance. Up to five DP722/DP730 handsets are supported on each DP752 while each
DP722/DP730 supports a range of up to 300 meters outdoors and 50 meters indoors from the base station.
The DP722/DP730 touts a suite of top-notch telephony features including support for up to 10 SIP accounts
per handsets, full HD audio, a 3.5mm headset jack, multi-language support, a speakerphone and more. When
paired with Grandstream’s DP752 DECT Base Station, the DP722/DP730 offers a powerful DECT VoIP
handsets that allows any business or residential user to create a cordless VoIP solution.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 12
PRODUCT OVERVIEW
Feature Highlights
The following tables contain the major features of the DP752 / DP730 / DP722:
Table 1: DP752 Features at a Glance
DP752

5 Handsets.

10 accounts.

10 Lines.

5 Concurrent calls.

PoE power support.

300m range outdoor / 50m range indoor.
Table 2: DP730 Features at a Glance
DP730

DECT cordless HD.

2.4 inch (240x320) color TFT LCD

500 hours standby / 40 hours talk time.

15 languages embedded.

10 accounts.

10 lines.

5 ring modes.
Table 3: DP722 Features at a Glance
DP722

DECT cordless HD.

1.8 inch (128x160) color TFT LCD

250 hours standby / 20 hours talk time.

15 languages embedded.

10 accounts.

10 lines.

5 ring modes.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 13
DP752 Technical Specifications
The following table resumes all the technical specifications including the protocols / standards supported,
voice codecs, telephony features, languages and upgrade/provisioning settings for the Base station DP752.
Table 4: DP752 Technical Specifications
Air Interface
Telephony standards: DECT
Frequency bands:
▪
1880 – 1900 MHz (Europe), 1920 – 1930 MHz (US)
▪
1910 – 1920 MHz (Brazil), 1786 – 1792 MHz (Korea)
▪
1893 – 1906 MHz (Japan), 1880 – 1895 MHz (Taiwan)
Number of channels: 10 (Europe), 5 (US, Brazil or Japan), 3 (Korea), 8 (Taiwan)
Range: up to 300 meters outdoor and 50 meters indoor
Peripherals
3 LED indicators: Power, Network, DECT.
Pairing/Paging button.
One 10/100 Mbps auto-sensing Ethernet port with integrated PoE
Protocols/Standards
SIP RFC3261, TCP/IP/UDP, RTP/RTCP, HTTP/HTTPS, ARP/RARP, ICMP, DNS
(A record, SRV, NAPTR), DHCP, PPPoE, SSH, TFTP, NTP, STUN, SIMPLE, LLDPMED, LDAP, TR-069, 802.1x, TLS, SRTP
Voice Codecs
G.711μ/a-law, G.723.1, G.729A/B, G.726-32, iLBC, G.722, OPUS, G.722.2/AMRWB (special order), in-band and out-of-band DTMF (in audio, RFC2833, SIP
INFO), VAD, CNG, PLC, AJB
Telephony Features
Hold, transfer, forward, 3-way conference, push to talk (DP730), intercom,
downloadable phonebook (XML, LDAP, up to 3000 entries), call waiting, call log
(up to 300 records), auto answer, flexible dial plan, server redundancy and fail-over
QoS
Security
Layer 2 QoS (802.1Q, 802.1p) and Layer 3 QoS (ToS, DiffServ, MPLS)
User and administrator level access control, MD5 and MD5-sess based
authentication, 256-bit AES encrypted configuration file, TLS, SRTP, HTTPS,
802.1x media access control, DECT authentication & encryption
Multi-language
Chinese Simple, Chinese Tradition, Czech, Danish, Dutch, English, Estonian,
Finnish, French, German, Hebrew, Hungarian, Japanese, Korean, Norwegian,
Portuguese, Romanian, Spanish, Swedish, Turkish.
Upgrade/
Firmware upgrade via TFTP/HTTP/HTTPS, mass provisioning using TR-069 or
Provisioning
AES encrypted XML configuration file
Multiple SIP
Up to ten (10) distinct SIP accounts per system
Accounts
Each handset may map to any SIP account(s)
Each SIP account may map to any handsets(s)
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 14
Ring Group
Flexible options when multiple handsets share the same SIP account
▪
Circular Mode:
All phones ring sequentially, starting with the phone after the one which
rang last.
▪
Linear Mode:
All phones ring sequentially in the predetermined order, starting with the
first phone each time.
▪
Parallel Mode:
All phones ring concurrently; after one phone answers, the remaining
available phones can make new calls
Power & Green
Energy Efficiency
Universal Power Supply Input AC 100-240V 50/60Hz; Output 5VDC, 1A; MicroUSB connection;
PoE: IEEE802.3af Class 1, 0.44W–3.84W
Package Content
Base unit, Universal Power Supply, Ethernet cable, Quick Installation Guide, GPL
Statement
Temperature
Operation: -10º to 50ºC (14 to 122ºF); Storage: -20º to 60ºC (-4 to 140ºF);
and Humidity
Humidity: 10% to 90% non-condensing
Compliance
FCC: FCC Part 15B; FCC Part 15D;MPE; FCC ID
CE:EN 55032; EN 55035; EN 61000-3-2; EN 61000-3-3; EN 60950-1; EN 301
489-1/-6; EN 301 406; EN 50385; RED NB Cert
RCM:AS/NZS 32; AS/NZS 60950.1.
ANATEL, EAC, UL(adapter).
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 15
DP730 Technical Specifications
The following table resumes all the technical specifications including the protocols / standards supported,
voice codecs, telephony features, languages and upgrade/provisioning settings for the DP730 handsets.
Table 5: DP730 Technical Specifications
Air Interface
Telephony standards: DECT
Frequency bands:
▪
1880 – 1900 MHz (Europe), 1920 – 1930 MHz (US)
▪
1910 – 1920 MHz (Brazil), 1786 – 1792 MHz (Korea)
▪
1893 – 1906 MHz (Japan), 1880 – 1895 MHz (Taiwan)
Number of channels: 10 (Europe), 5 (US, Brazil or Japan), 3 (Korea), 8 (Taiwan)
Range: up to 300 meters outdoor and 50 meters indoor
Peripherals
2.4 inch (240x320) color TFT LCD
27 keys including 3 soft keys, 5 navigation/ menu keys, 4 dedicated function keys
for SEND, POWER/END, SPEAKERPHONE, MUTE, 3 side keys including 2
volume (up and down) and 1 Push-to-Talk key
3-color MWI LED
3.5mm headset jack
Proximity and accelerometer sensors
Backlit keypad
Removable belt clip
Micro-USB port for alternative charging and non-battery operation
Protocols/Standards
Voice Codecs
Hearing Aid Compatibility (HAC) compliant
G.722 codec for HD audio and G.726 codec for narrow band audio (G.711μ/a-law,
G.723.1, G.729A/B, iLBC and OPUS are supported via companion DECT base
station DP752), AEC, AGC, Ambient noise reduction on microphone capturing and
advanced noise suppression on audio playing
Telephony Features
Hold, transfer, forward, 3-way conference, push-to-talk (DP730), intercom, call
park, call pickup, downloadable phonebook, call waiting, call log, auto answer,
click-to-dial, flexible dial plan
HD Audio
Yes, in both Handsets and Speakerphone modes
Security
DECT authentication & encryption
Multi-language
Chinese Simple, Chinese Tradition, Czech, Danish, Dutch, English, Estonian,
Finnish, French, German, Hebrew, Hungarian, Japanese, Korean, Norwegian,
Polish, Portuguese, Romanian, Spanish, Turkish.
Upgrade/
Software Upgrade Over-The-Air (SUOTA), handsets provisioning Over-The-Air
Provisioning
Multiple Line
Each handset may access up to 10 lines
Access
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 16
Power & Green
Energy Efficiency
Universal Power Supply Input AC 100-240V 50/60Hz; Output 5VDC 1A; Micro-USB
connection;
Rechargeable Li-ion battery (500 hours of standby time and 40 hours of talk time)
Package Content
Handset unit, universal power supply, charger cradle, belt clip, 1 battery, Quick
Start Guide
Temperature
Operation: -10º to 50ºC (14 to 122ºF); Charging: 0 to 45ºC (32 to 113ºF); Storage:
and Humidity
-20º to 60ºC (-4 to 140ºF); Humidity: 10% to 90% non-condensing
Compliance
FCC: FCC Part 15B; FCC Part 15D; SAR (FCC 47 CFR Part2.1093; IEEE 1528;
IEC 62209-2); FCC Part68 HAC; FCC ID
CE:EN 55032; EN 55035; EN 61000-3-2; EN 61000-3-3; EN 60950-1;EN 301
489-1/-6; EN 301 406; EN 50332-2; SAR(EN50360;EN50566;EN 50663;EN622091; EN62209-2; EN 62479); RED NB Cert
RCM:AS/NZS CISPR32; AS/NZS 60950.1;AS/CA S004;AS/ACIF S040.
ANATEL, EAC, UL(adapter).
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 17
DP722 Technical Specifications
The following table resumes all the technical specifications including the protocols / standards supported,
voice codecs, telephony features, languages and upgrade/provisioning settings for the DP722 handsets.
Table 6: DP722 Technical Specifications
Air Interface
Telephony standards: DECT
Frequency bands:
▪
1880 – 1900 MHz (Europe), 1920 – 1930 MHz (US)
▪
1910 – 1920 MHz (Brazil), 1786 – 1792 MHz (Korea)
▪
1893 – 1906 MHz (Japan), 1880 – 1895 MHz (Taiwan)
Number of channels: 10 (Europe), 5 (US, Brazil or Japan), 3 (Korea), 8 (Taiwan)
Range: up to 300 meters outdoor and 50 meters indoor
Peripherals
1.8 inch (128x160) color TFT LCD
23 keys including 2 softkeys, 5 navigation / menu keys, 4 dedicated function keys
for SEND, POWER/END, SPEAKERPHONE, MUTE
3-color MWI LED
3.5mm headset jack
Removable belt clip
Micro-USB port for alternative charging and non-battery operation
Protocols/Standards
Voice Codecs
Hearing Aid Compatibility (HAC) compliant
G.722 codec for HD audio and G.726 codec for narrow band audio (G.711μ/a-law,
G.723.1, G.729A/B, iLBC and OPUS are supported via companion DECT base
station DP752), AEC, AGC, Ambient noise reduction on microphone capturing and
advanced noise suppression on audio playing
Telephony Features
Hold, transfer, forward, 3-way conference, push to talk, call park, call pickup,
downloadable phonebook, call waiting, call log, auto answer, click-to-dial, flexible
dial plan
HD Audio
Yes, in both Handsets and Speakerphone modes
Security
DECT authentication & encryption
Multi-language
Chinese Simple, Chinese Tradition, Czech, Danish, Dutch, English, Estonian,
Finnish, French, German, Hebrew, Hungarian, Japanese, Korean, Norwegian,
Polish, Portuguese, Romanian, Spanish, Turkish
Upgrade/
Software Upgrade Over-The-Air (SUOTA), handsets provisioning Over-The-Air
Provisioning
Multiple Line
Each handset may access up to 10 lines
Access
Power & Green
Universal Power Supply Input AC 100-240V 50/60Hz; Output 5VDC 1A; Micro-USB
Energy Efficiency
connection; Rechargeable 800mAh Ni-MH Low Self-Discharge (LSD) AAA
batteries (250 hours of standby time and 20 hours of talk time)
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 18
Package Content
Handsets unit, universal power supply, charger cradle, belt clip, 2 batteries, Quick
Installation Guide
Temperature
Operation: -10º to 50ºC (14 to 122ºF); Charging: 0 to 45ºC (32 to 113ºF); Storage:
and Humidity
-20º to 60ºC (-4 to 140ºF); Humidity: 10% to 90% non-condensing
Compliance
FCC: FCC Part 15B; FCC Part 15D; SAR (FCC 47 CFR Part2.1093; IEEE 1528;
IEC 62209-2); FCC Part68 HAC; FCC ID
CE:EN 55032; EN 55035; EN 61000-3-2; EN 61000-3-3; EN 60950-1;EN 301
489-1/-6; EN 301 406; EN 50332-2; SAR(EN50360;EN50566;EN 50663;EN622091; EN62209-2; EN 62479); RED NB Cert
RCM:AS/NZS CISPR32; AS/NZS 60950.1;AS/CA S004;AS/ACIF S040.
ANATEL, EAC, UL(adapter).
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 19
GETTING STARTED
This chapter provides basic installation instructions including the list of the packaging contents and also
information for obtaining best performance with the DP730/DP722 IP DECT phone and its base station DP752.
Equipment Packaging
Table 7: Equipment Packaging – DP752
DP752
•
1 Base unit
•
1 Universal power supply 5V
•
1 Bracket
•
1 Ethernet cable
•
1 Quick Installation Guide
•
1 GPL Statement
Figure 1: DP752 Package Content
Table 8: Equipment Packaging – DP730
DP730
•
1 Handset unit
•
1 Universal power supply 5V
•
1 Charging station
•
1 Handset Belt
•
1 Rechargeable Li-ion battery
•
1 Quick Installation Guide
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 20
Figure 2: DP730 Package Content
Table 9: Equipment Packaging – DP722
DP722
•
1 Handset unit
•
1 Universal power supply 5V
•
1 Charging station
•
1 Handset Belt
•
2 Rechargeable batteries
•
1 Quick Installation Guide
Figure 3: DP722 Package Content
Note: Check the package before installation. If you find anything missing, contact your system administrator.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 21
Connecting DP752
To setup the DP752 Base Station, please follow the steps below:
Network
Power
Socket
Input
Figure 4: DP752 Back View
You have two options for power and network connection of the base station: AC power or Power over Ethernet
(PoE).
Note: For better signal range, we recommend to install DP752 with LED side facing toward the usage area.
Ceiling mount is recommended for better coverage.
Connecting via AC power
1. Connect the micro-USB connector into the related port on the base station and connect the other end
of the power adapter into an electrical power outlet.
2.
Connect the supplied Ethernet cable between the Internet port on the base station and the Internet
port in your network or the switch/hub device port.
Connecting via PoE
To connect the base station using PoE, you need to connect the Ethernet cable provided (or 3rd party network
cable) between the Network Socket on the base station to Ethernet port of your PoE switch/hub.
Setting up DP730/DP722 Handsets
Please follow below steps to insert batteries into the Handsets:
•
Open the battery compartment cover.
•
For DP730: Inset Li-ion battery with the electrodes in the bottom left corner.
•
For DP722: Insert AAA batteries with correct polarity (+ / -).
•
Close the battery compartment cover.
Note: Please charge the batteries fully before using the Handsets for the first time
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 22
1
1. Battery compartment cover of DP730
2. Battery
3. Rear of DP730
4. Battery compartment cover of DP722
5. AAA Batteries
6. Rear of handset
Figure 5: Setting up the DP730/DP722
Battery Information
Table 10: DP722/DP730 Battery Specifications
DP730 battery specifications
DP722 Batteries Specifications
•
Technology: Nickel Metal Hydride (Ni-MH)
•
Technology: Li-ion
•
Size: AAA
•
Nominal Voltage: 3.8V
•
Voltage: 1.2V
•
Capacity: 1500mAh
•
Capacity: 800mAh
•
Charging time: 12 hours from empty to full
•
Charging time: 12 hours from empty to full
•
Standby time: up to 500 hours
•
Standby time: up to 250 hours
•
Talk time: up to 40 hours’ active talk time
•
Talk time: up to 20 hours’ active talk time
In order to get the best performance of your DP730/DP722 Handsets, we recommend using original batteries
provided in the package or batteries compliant with above specifications.
The specifications may differ depending on the age and capacity of the batteries used.
Important Note: Be careful when inserting the batteries into your handset to avoid any risk of short-circuit,
which lead to damage your batteries and/or the handset itself. Do not use damaged batteries which can
increase the risk of serious harm.
Setting up the Charge Station
Please refer to the following steps for setting up the charge station and charging the Handsets:
1. Connect the DC plug on the power adapter to the micro-USB connector on the charge station.
2. Connect the other end of the power adapter into an electrical power outlet.
3. After setting up the Handsets and the charge station, place the Handsets in the charge station.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 23
Figure 6: Setting up Charging Stations
DP752 LED Patterns
The DP752 has 5 LED lights on it. Please refer to the following table for the meaning of each light.
Figure 7: DP752 LED Patterns
Table 11: DP752 LED Patterns
LED Light
Status
Indicates Power ON/OFF.
Indicates status of SIP account registration and network
•
Solid ON: SIP account registered.
•
Blinking: SIP account not registered or network error
Indicates status of the DECT handset registration:
•
Solid ON: Handset registered to base.
•
Fast Blinking (0.25s ON/0.25s OFF): Paging handset.
•
Blinking (0.5s ON/0.5s OFF): Pairing mode.
DP730/DP722 Handsets Description
The LCD screen and the Keypad are the main hardware components of the DP730/DP722.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 24
Figure 8: DP722 Keys Description
Table 12: Keypad Keys Description
Key
Description
1.
Earphone
Delivers audio output.
2.
LED Indication
Red: Charging. Green: Charge completed.
Blinking: Missed call(s) or Voice Mail received.
3,5
Left and right softkeys
Correspond to functions displayed on the LCD. These functions
change depending on the current context.
4.
LCD display
Shows call information, handset status icons, prompt messages,
etc.
6.
4 Arrow key combination
Permits navigation of the cursor through the displayed menu options.
7.
Men/Ok key
Selects the option chosen by the cursor. (Enters the main menu
from the home screen.)
8.
Off-hook / Dial key
Enters dialing mode, or dials number entered.
9.
On-hook / Power key
Terminates calls, or turns the handset on / off.
10.
Alphanumeric Keypad
Provides the digits, letters, and special characters in contextsensitive applications. For + sign, press and hold key 0.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 25
11.
# / Lock key
Locks keypad against unintentional entries when keep pressing #.
• Press and hold # key for approximately 2 seconds to lock the keys.
Press Unlock softkey and then # to unlock the keys.
12.
Mute key
Activates or deactivates the mute feature.
13.
Hands-free / Speaker key
Switches between handset and hands-free / speaker modes.
14.
Microphone
Picks up audio earpiece and hands-free calls.
Figure 9: DP730 Keys Description
Table 13: Keypad Keys Description
Key
1.
Proximity sensor
Description
The proximity senor can detect
and measure gravitational
acceleration, tilt, vibration, altitude changes, and static position.
2.
Earphone
Delivers audio output.
3,4
Volume up / Down Keys
Configure the handset and ringtone volume.
5.
PTT Key
PTT (Push-to-Talk) button, to initiate PTT call.
6.
Hands-free / Speaker
Switches between Handset and Hands-free / Speaker modes.
key
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 26
7.
Arrow key combination
Allows navigation of the cursor through the displayed menu options.
(Up, Down, Left, Right)
8.
Off-hook / Dial key
Enters dialing mode, or dials number entered.
9.
Alphanumeric Keypad
Provides the digits, letters, and special characters in context-sensitive
applications. For + sign, press and hold key 0.
10.
* / Silent Mode key
Activates or deactivates the silent mode (no ringtone heard during
incoming call) when keep pressing on * in idle screen.
11.
LED indicator
1dual-color LED indicator indicating: power, call, battery, message
waiting…
12.
3.5 mm headset jack
Phone connector for the headphones/headsets.
13.
Color LCD Screen
2.4-inch (240x320) TFT color LCD
14.
Softkeys
Correspond to functions displayed on the LCD. These functions
change depending on the current context.
15.
Mute
Mute microphone during conversation.
16.
Menu/OK key
Selects the option chosen by the cursor or enters the main menu from
the home screen.
17.
On-hook or Power key
Terminates calls or turns the handset on / off.
18.
# / Lock key
Locks keypad against unintentional entries when keep pressing #.
• Press and hold # key for approximately 2 seconds to lock the keys.
• Press Unlock softkey and then # to unlock the keys.
19.
Microphone
Picks up audio earpiece and hands-free calls.
DP730/DP722 Icons Description
The following table contains description of each icon that might be displayed on the LCD screen of the
DP730/DP722 Handsets.
Table 14: DP730/DP722 Icons Description
Battery status
Not equipped with battery
Battery status
Battery empty
Battery status
Battery low
Battery status
Battery normal
Battery status
Battery full
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 27
Battery status
Charging
Signal status
Not subscribed
Signal status
Not in range
Signal status
Signal very low
Signal status
Signal low
Signal status
Signal normal
Signal status
Signal good
Signal status
Signal very good
Microphone MUTE Status
OFF - Not muted
ON – Muted
Speaker status
OFF - Speaker is inactivated
ON - Speaker is activated
Headset icon
Missed Call icon
Voicemail icon
Ringtone status
OFF - Ringtone off (Silent mode)
ON - Ringtone on
Keypad Lock status
OFF - Keypad unlock
ON - Keypad locked
Incoming Call notification
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 28
Outgoing Call notification
Missed Call notification
Voicemail notification
Contacts
Call History
Registration
Voice Mail
Preferences
Shortcut
Call features
Status
Settings
DP730/DP722 Handsets Menu
The Handsets has an easy-to-use menu structure. Every menu opens a list of options. To open the main
menu, press “Menu” (left softkey) when the Handsets is on and in standby mode. Press Arrow keys to
navigate to the menu option you require. Then press “Select” (left softkey) or OK/Selection key to access
further options or confirm the setting displayed. To go to the previous menu item, press “Back” (right softkey).
You can press Power key at any time to cancel and return to standby mode. If you do not press any key, the
Handsets automatically reverts to standby mode after 20 seconds.
Note: Users can navigate by through handset menu by pressing menu number when displayed.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 29
Contacts
Call History
Registration
Voice Mail
Preferences
Shortcut
Call Features
Status
Settings
Private/Global Phonebook
1. Missed Calls
2. Accepted Calls
3. Outgoing Calls
4. All calls
1. Register
2. Deregister
3. Select Base
1. Play Message
2. Set Voice Mail
3. Set Key 1
Outgoing Default Line
Auto Answer
Off-Cradle Pickup
On-Cradle Hangup
Mute as DND
Disable Busy Tone
Disable CW Tone
Onhook Backlight
Cradle Backlight
SIP Account Display
Customizing keys functions
Speed dial
Set Key 1
1. Do Not Disturb
2. Call Forward
3. Call Waiting
1. Base Status
2. Handset Status
3. Line Status
1. Handset Name
2. Phone Language
3. Date / Time
4. Audio
5. Display
6. Network Settings
7. SIP Settings
8. System Settings
9. Firmware Upgrade
10. Factory Functions
1. Advisory Tone
2. Ringtones
3. Volume
LCD Timeout (Idle)
LCD Timeout (Call)
Menu Timeout
Message Waiting Prompt
LCD Brightness
1. Change Base PIN
2. Factory Reset
3. Reboot Base
4. Repeater Mode
1. Diagnostic Mode
2. Audio Loopback
3. LCD ON /OFF
4. LCD Diagnostic
5. System Monitoring
Figure 10: DP730/DP722 Menu Structure
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 30
Contacts
•
Private: Private contacts include contacts visible in the current Handsets only.
•
Global: Global phonebook contacts are the contacts shared between the
Handsets subscribed to the DP752 base station.
Note: Private/Global Phonebooks will be merged on the handset.
Call History
Display the call history:
1. Missed Calls.
2. Accepted Calls.
3. Outgoing Calls.
4. All Calls.
Note: You can add contacts to Shared Contacts directly from call logs.
Registration
•
Register
Register your handset to base station.
•
Deregister
Deregister your handset from base station.
•
Select Base
Select base station.
Voice Mail
1. Play Message
Play voice mail messages received.
2. Set Voice Mail
Configure voice mail parameters.
3. Set Key 1
Configure Key 1 as VM speed dial for selected account.
Preferences
•
Outgoing Default Line
Select account to be use by default for outgoing calls.
•
Auto Answer
Enable/Disable Auto Answer. (Default is Disabled).
•
Off-Cradle Pickup
Enable/Disable Off-Cradle Pickup. If enabled, users can answer the calls by
picking up the handset off-cradle. (Default is Disabled).
•
On-Cradle Hangup
Enable/Disable On-Cradle Hangup. If enabled, users can end the call by placing
the handset on-cradle. (Default is Disabled).
•
Mute as DND
Enable/Disable Mute as DND. If enabled, pressing mute key on idle state will
set the phone to DND mode. (Default is Disabled)
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 31
•
Disable Busy Tone
Enable/Disable Busy Tone. If set to enabled, busy tone will not be played.
(Default is Disabled).
•
Disable CW Tone
Enable/Disable CW Tone. If set to enabled, Call Waiting Tone will not be played.
(Default is Disabled).
•
Onhook Backlight
Enable/Disable Onhook Backlight. If enabled, pressing
key on idle screen
will switch off LCD screen. (Default is Disabled)
•
Cradle Backlight
Enable/Disable/Dim Cradle Backlight. If enabled, LCD will remain backlit when
the handset is placed on-cradle/charging. If set to “Dim”, LCD brightness will be
reduced when the handset is placed on-cradle/charging. (Default is Disabled)
•
SIP Account Display
Select which SIP Account information will be displayed on the screen.
Shortcut
•
▪
Name Only: Display SIP Account Name only. (Default)
▪
ID Only: Display SIP User ID only.
▪
None: No account information will be displayed.
Customizing keys functions
: Configure Left Softkey function in idle. Function can be set as Menu, History,
Contacts, Line or PTT. Default is Menu.
: Configure Right Softkey function. Function can be set as History, Contacts,
Line or PTT Default is Contacts.
: Configure Arrow UP Key function. Default is Outgoing Calls (Call History).
: Configure Arrow DOWN key function. Default is Accepted Calls (Call History).
: Configure Arrow LEFT key function. Default is Ringer Volume Down.
: Configure Arrow RIGHT key function. Default is Ringer Volume Up.
Select key and press OK button to configure function. Following functions are
available for arrow keys: 1. Disabled, 2. Menu, 3: Missed Calls, 4: Accepted Calls,
5: Outgoing Calls, 6: History, 7: Contacts, 8: Status, 9: Line, 10: Voice Mail, 11:
Ringer Volume Up, 12: Ringer Volume Down, 13: Audio Volume Up, 14: Audio
Volume Down.
•
Speed Dial
Assign contact numbers as speed dial.
Select a key [2], [3], [4], [5], [6], [7], [8] or [9] and press OK button. Select “Edit”
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 32
to manually specify the destination number, or select “From Contacts” to select
a contact as speed dial destination.
•
Set Key 1
Configure Key 1 as VM speed dial for selected account.
Call Features
1. Do Not Disturb
Enable/disable do not disturb mode on the phone.
2. Call Forward
Configure call forward feature.
3. Call Waiting
Configure call waiting feature.
Status
1. Base Status
Display Base status (Firmware, IP address, Subnet mask, Gateway, MAC
Address)
2. Handset Status
Display Handsets status (Model RF, Firmware, IPEI)
3. Line Status
Display Line status (Account name, Status)
Settings
1. Handset Name
Change the Handset name.
2. Phone Language
Select the language to be displayed on the phone's LCD. (Default is English.)
3. Date/Time
Configure date and time on the Handsets.
4. Audio
Specify ringtones for internal/external calls, the volume, advisory tones (Keypad,
Confirmation, Low battery notifications) and Vibration mode (DP730 only).
5. Display
Configure backlight, LCD timeout (Idle/Call), LCD brightness, Message Waiting
Prompt and menu key timeout.
6. Gestures (DP730 only)
Configure Close-to-Ear Backlight and Facedown Hangup.
7. Network Settings
Configure IP addresses and select DHCP/Static IP mode.
8. SIP Settings
Configure/View SIP accounts settings.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 33
9. System Settings
Change Base PIN code, perform factory reset, reboot base and configure
repeater mode.
10. Firmware Upgrade
Upgrade the firmware version of the Handsets.
11. Factory Functions
Diagnostic Mode (DP722) / Keypad Diagnostic (DP730)
All LEDs will light up, and the LCD will display a table listing the names of all
keys in red. Press any key to diagnose; the key's name will display in blue. After
all keys are diagnosed, a prompt message (“PASS”) will display; press “Back”
(right softkey) to exit.
Note: User can long press arrow UP key to exit at any time.
Audio Loopback
Speak to the phone using speaker/Handsets/headset. If you can hear your
voice, your audio is working fine. Press “Exit” softkey to exit audio loopback
mode.
LCD ON / OFF
Select this option to turn off LCD. Press any button to turn on LCD.
LCD Diagnostic
Select this option to enter LCD Diagnostic mode. Press “Next” (left softkey) to
display white screen. Continue pressing the left softkey to view all remaining
screens (black, blue, red, and green) and then exit. End the test early by
pressing the right softkey.
System Monitoring
Displays RSSI, battery voltage and RPN information.
Vibration (DP730 only)
Test vibration on DP730.
Acceleration Sensor (DP730)
Displays X, Y, Z coordinates.
Proximity Sensor (DP730)
Test proximity sensor on DP730.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 34
BASIC OPERATIONS
Turning the Handsets ON / OFF
To turn ON the handsets
Long press on Power key
until the LCD screen lights up.
To turn OFF the handsets
Long press on Power key
again when the handsets is idle until the display turns off.
Setup Wizard
Setup wizard shows at first access to DP722/DP730 or factory reset allowing users to configure handsets
language and date/time. Users can quit at any time by pressing "Skip" (left softkey).
Register DP730/DP722 Handsets to DP752 Base Station
1. On DP752 Base station, press and hold the Radio/Page
button for 4 seconds until the Radio
icon starts blinking to start Subscription process. Or Access web UI, and press Subscribe icon
to Open Subscription.
2. On DP730/DP722, press “Subscribe” softkey if available on the main screen or access Menu →
Registration → Register while the DP752 Radio icon is blinking.
Note: “Subscribe” softkey appears only if DP730/DP722 is not registered to any DP752 base station.
3. Select BaseX (X=1-4) corresponding to the desired base station DP752, then press Subscribe.
4. The DP730/DP722 will search for nearby base stations and will display the RFPI code and Base
station name of the discovered DP752.
5. Press Subscribe to pair with the displayed DP752.
6. The DP730/DP722 will display Easy Pairing on the LCD and play an audible buzz when successful.
Then it will return to the home screen, displaying the Handsets name and number assigned by the
registered base station.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 35
Figure 11: Registration Process
Using DP730/DP722 with Multiple DP752 Base Stations
DP730/DP722 is able to be registered to up four different DP752 base stations.
Registering DP730/DP722 to an additional DP752 base station
Considering DP730/DP722 is previously registered to an initial base station, please follow below steps to
register a Handset to an additional base station:
1. Press Menu (left softkey or the selection key) to bring up operation menu.
2. Use arrow keys to reach Registration and select Register.
3. Navigate to an unsubscribed base using arrow keys, and click on Subscribe.
4. Make sure that the subscription is opened on the new base station.
Figure 12: Multiple Base Stations Registration
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 36
Switching Between Different Base Stations
1. Press “Menu” (left softkey or the selection key) to bring up operation menu.
2. Use arrow keys to reach Registration.
3. Navigate to Select Base using arrow keys.
4. Select the desired base station and press Select.
Figure 13: Switching Between Base Stations
Unregister the DP730/DP722
•
Using DP730/DP722 Handsets:
1. On DP730/DP722, press “Menu” (left softkey or the selection key) to bring up operation menu.
2. Press arrow keys to move the cursor to Registration, then press “Select” (left softkey).
3. Navigate to Deregister.
4. Select the Handsets to be unregistered and press “Deregister” (left softkey).
5. Enter the system PIN code (default: 0000).
6. Press “Done” (left softkey) to confirm or “Back” (right softkey) to cancel.
•
Using DP752 Base Station UI:
1. Access DP752 Web Interface.
2. Go to Status → DECT Base Status.
3. Locate the Handsets to unregister and press “Unsubscribe” button.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 37
Figure 14: Unregister DP730/DP722 from DP752 web UI
Setting the Key Lock
You can lock the keypad against unintentional entries. It is, however, still possible to pick up incoming calls
even with the keypad locked.
• To enable the Keypad Lock
1. Press the Pound key “#”
and hold for approximately 2 seconds.
2. The display shows Keypad Locked briefly and the key lock icon
appears in the display.
• To disable the Keypad Lock
1. Press and hold Pound key “#”
to unlock the keys.
2. Keypad Unlocked appears briefly in the display and a windows prompt will be displayed to confirm
that the keypad is unlocked.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 38
Locating a DP730/DP722 Handset from DP752 Base station
In some situations, you may have a DP730/DP722 Handsets incorrectly positioned and you don’t know its
current location. You can locate a DP730/DP722 Handsets from his registered DP752 base station using
below steps:
Locate via DP752 Web UI
1. Access the Web GUI of your DP752 using the admin’s username and password.
2. Press Login to access your settings and navigate to Status → DECT Base Status tab.
3. Choose which Handsets to locate and press its corresponding Page button.
4. A paging call will be received on the selected DP730/DP722 Handsets.
Note: If you press Page All icon
, all registered DP730/DP722 handsets will be receiving paging
call.
5. Once located, you can press End Softkey to end paging call.
Figure 15: Locate Handsets via Web UI
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 39
Locate via DP752 Base station
1. On DP752 Base station front side, press Radio/Page
button.
2. All registered Handsets will receive Paging call.
3. Once located, you can end the paging calling by pressing any key on the Handsets or by pressing
again Radio/Page button.
Checking System Status
You can view the system status on your handsets including the following information of the system:
Table 15: DP752 Info description
Item
Description
Firmware
Current firmware version installed on DP722/DP730.
IP Address
IP address of the base station DP752 if registered.
Subnet Mask
Subnet Mask of the base station DP752 if registered.
Gateway
Gateway IP of the base station DP752 if registered.
MAC address
MAC address of the base station DP752 if registered.
Table 16: DP722/DP730 Info description
Item
Description
Model (RF)
Displays the product model, hardware version and DECT region of
DP722/DP730. i.e.: DP722/DP730 1.4A (EU)
Firmware
Current firmware version installed on DP722/DP730.
IPEI
International Portable Equipment Identifier.
Unique “serial number” for DECT handsets.
•
To check the Handsets Status
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Status menu
•
, then select Handset Status.
To check the Base Status
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Status menu
, then select Base Status.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 40
Basic Network Settings
Once connected to the network, DP752 base station will attempt to contact a DHCP server to obtain valid
network settings (e.g., IP address, subnet mask, gateway address and DNS address) by default.
The users could also configure basic network settings manually from a registered DP722/DP730 Handsets.
In order to configure the network settings manually, please follow the steps below:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
and access Network Settings menu.
3. Enter the system PIN code (default: 0000) and press the softkey “Done”.
4. To change to static IP, press
or
to select Static from the IP Settings field.
5. Enter valid values in the IP Address, Subnet Mask, Gateway, DNS Server fields.
6. Press softkey “Save” to save and apply the new changes.
Note: A prompt message will be displayed to confirm that the new settings are saved successfully
7. The DP722/DP730 will display a reboot confirmation message, select “Yes” to apply the new settings
or “No” to avoid rebooting the DP752.
Figure 16: Network Settings Configuration
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 41
Change Menu and LCD Timeout
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to Display, and then press “Select” (left softkey).
4. Set desired time in seconds for Backlight timeout and for Menu timeout. Available value: 15
seconds, 30 seconds, 60 seconds or disabled. (Default is 30 seconds)
5. Press Save (left softkey) to save and apply the new settings.
Return to Idle Screen
Press the Power Key
to quickly exit the menu and return back to the main idle screen.
If you do not press any key in a period of time, the LCD screen will automatically exit the menu and return to
the idle screen as well.
When you are navigating on the handset’s menu, and you receive an incoming call, the LCD screen will
automatically exit the menu and you can either accept or reject the call. When the call is terminated, the LCD
screen will return back to the idle screen.
Register SIP Account
Register Account via Web User Interface
1. Access the Web GUI of your DP752 using the admin’s username and password.
2. Press Login to access your settings and navigate to Profiles tab and select a profile to use.
DP752 supports up to 4 profiles. A profile is a set of settings including general settings, network settings,
SIP setting, audio setting, call settings and ring tones, etc.
A profile can be used with different SIP accounts.
3. In General Settings, set the following:
a. Profile Active to Yes.
b. SIP Server field with your SIP server IP address or FQDN.
c.
Failover SIP Server with your Failover SIP Server IP address or FQDN. Leave empty if not
available.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 42
d. Prefer Primary SIP Server to No or Yes depending on your configuration. Set to No if no
Failover SIP Server is defined. If “Yes”, account will register to Primary SIP Server when
failover registration expires.
e. Outbound Proxy with your Outbound Proxy IP Address or FQDN. Leave empty if not
available.
4. Press Save and Apply to save your configuration.
Figure 17: SIP Settings
5. Go to DECT →SIP Account Settings
6. Configure your SIP details in desired account:
a. Account: Select Account row to configure (Account 1 – Account 10).
b. SIP User ID: User account information, provided by VoIP service provider (ITSP). Usually in
the form of digit similar to phone number or actually a phone number.
c.
Authenticate ID: SIP service subscriber’s Authenticate ID used for authentication. Can be
identical to or different from SIP User ID.
d. Password: SIP service subscriber’s account password to register to SIP server of ITSP. For
security reasons, the password will field will be shown as empty.
e. Name: Any name to identify this specific user.
f.
Profile: Select the corresponding Profile ID (1/2/3/4).
g. HS Mode: Assign the account to specific Handsets (HS1, HS2…) or hunting group mode.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 43
h. Active: Set to Yes. If set to No, account is disabled and will not register.
7. Press Save and Apply to save your configuration.
Figure 18: SIP Accounts Settings
After applying your configuration, your phone will register to your SIP Server.
You can verify if your DECT phone has registered with your SIP server from your DP752 web interface
under Status → Account Status (a green background with Yes under SIP Registration column for
corresponding account indicates the account(s) has been successfully registered).
Figure 19: Account Status
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 44
PHONE SETTINGS
This chapter will help you with the instruction for configuring and changing the settings of your DP722/DP730,
Editing the Handset Name
The procedure to change the handset name is as follows:
•
Using DP722/DP730 Handsets:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Handsets Name, and then press “Select”.
4. Enter the desired name and press “Rename” and then the DP722/DP730 will display a confirmation
message that the rename operation was successful.
Figure 20: Handsets Name editing
•
Using DP752 Base Station UI:
1. Access DP752 Web Interface.
2. Go to DECT → General Settings.
3. In “Handsets Settings” section, change Handsets Name to desired name.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 45
Figure 21: Edit Handsets Name from DP752
Changing the Base PIN Code
Users can change their code PIN by following the steps below:
•
Using DP722/DP730 Handsets:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select System Settings, and then press “Select”.
4. Enter the current code PIN (By Default is 0000), a new window will be displayed inviting you to enter
the new password, when done press “Save” (left softkey) and a prompt message will be displayed to
confirm that the new code PIN has been saved successfully.
Figure 22: Changing Admin Base PIN Code from DP722/DP730
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 46
•
Using DP752 Base Station UI:
1. Access DP752 Web interface.
2. Go to DECT → General Settings.
3. Set new PIN code in Admin PIN Code field.
Note: Only digits accepted. Minimum allowed length is 4 digits.
Figure 23: Changing Admin Base PIN Code from DP752
Selecting Phone Language
The DP722/DP730 supports displaying texts in different languages. The handsets supports 20 languages
(see the table of the technical specifications). The default language of the handsets is English. You can
change the language according to your requirement. To change the language of the handsets, please proceed
as follows:
1. Press Menu (left softkey or the selection key) to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Phone language, then select the desired language and press “Select” (Left
softkey). The LCD screen prompts “Change phone language to xxx (xxx it’ the language you selected)”
4. Press “Yes” (left softkey) to accept the change. Text displayed on the handsets will change to the
selected language.
Figure 24: Handsets Language
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 47
Activate/Deactivate Hands-Free Mode
This function allows you to make a call without having to hold the handsets in your hand.
1. Press the Hands-free key
while you are making a call or on the idle screen to activate hands free
mode.
2. Press the Hands-free key
again to deactivate the hands-free function.
Muting the Microphone
Press the Mute key
to switch off the microphone during an established call. You can now talk freely
without the other party hearing you and the icon of mute
key
will be displayed on the screen. Press the Mute
again to switch the microphone back on.
Adjusting Speaker and Earpiece Volume
Press left key
or right key
while you are on an established call to set the volume of the earphone /
speaker. You can choose between 5 different levels. The default level is 3:
Volume 1
Volume 4
Volume 2
Volume 5
Volume 3
Ringtones
Setting the Ringer Volume on the Handsets
You can adjust the ringer volume for an incoming call to one of 6 levels (level 1 to 5 and off). Level 5 is the
highest level. (The DP722/DP730 Handsets are set to level 3 by default).
In order to configure the desired ringer volume, proceed as follows:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Audio (For DP722) and Audio & Vibration (for DP730) → Volume.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 48
4. Press the left and right arrow keys to change repeatedly and set the desired volume.
5. Press “Save” to confirm the volume, and a message prompt will be displayed to confirm that the new
volume has been successfully saved.
If you select OFF, the icon
appears in the display and the handsets will not ring for incoming calls.
Figure 25: Ringer Volume
Setting Ringtones on the Handsets
You can change the ringtone for an incoming call. The device has 9 different ringer melodies for you to choose
from (System Ring, Ring 1-8).
The default setting for the ring tone for a call is melody 1.
In order to configure the desired melody, proceed as follows:
1. Press Menu (left softkey or the selection key) to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Audio → Ringtones.
4. Press “Select” (left softkey) to confirm the ringtones selected and a message prompt will be displayed
to confirm that the new ringtones has been set successfully.
Figure 25: Calls Ringtones
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 49
Advisory Tones
Advisory tones are acoustic signals, which inform you of different actions and states on your handsets. The
following advisory tones can be configured independently of each other:
▪
Keypad tone: it’s played when a user presses any key of the keypad (even during calls).
▪
Confirmation: it’s played when a user saves settings or places the handsets in the charger cradle.
▪
Low battery: it’s played if the capacity of the batteries is low or the handsets requires charging.
To configure the advisory tones
1. Press Menu (left softkey or the selection key) to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Audio → Advisory tones, and choose which tone you want to change it.
4. Press the left and right arrow keys to either enable or disable the desired tones.
5. Press “Save” (left softkey) to confirm, and a message prompt will be displayed to confirm that the
new settings has been successfully saved.
Figure 26: Advisory Tone
Ringtones Customization
DP752/730/722 allow users to use custom ringtones. Custom ringtones will be stored on DP752 base station
and only selected custom ringtone will be downloaded to specific DP722/DP730 handsets.
DP752 base station supports up to 10 custom ringtones.
Custom ringtone should be generated using GS Ringtone Tool and named ring[1-10].bin (example: ring1.bin ,
ring6.bin).
To use custom ringtones, follow below steps:
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 50
Step 1: Generate Custom Ringtone(s)
1. Download “Ringtone Generator” tool available at http://www.grandstream.com/support/tools
2. Run the tool and select your ringtone file to convert.
Figure 27: Generating Custom Ringtone (Windows)
Notes:
Currently only 16-bit linear PCM audio is supported for .wav files. The sampling rate should be
automatically detected and the audio will automatically be down sampled to 8kHz. Stereo channels
are also detected and mixed to produce mono output.
.pcm files should be pre-formatted to 16-bit 8kHz mono format.
3. Press “Generate Ringfile” to finish the process. Ringtone with filename “ring1.bin” will be created at
same location as ringtone tool.
Step 2: Download Custom Ringtone(s) to DP752 Base Station
1. Make generated ringtone files available in your TFTP, HTTP or HTTPS server.
2. Access DP752 Web GUI and go Maintenance → Firmware Upgrade page.
3. Set “Upgrade Via” to TFTP, HTTP or HTTPS (depending on server type hosting ringtone files).
4. Set “Firmware Server Path” to IP address or the FQDN of the server.
5. Set “Firmware Upgrade and Provisioning” to “Always Check for New Firmware”.
6. Update the change by clicking the "Save and Apply" button. Then "Reboot" or power cycle the base
station to download the ringtone(s).
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 51
Figure 28: Downloading Custom Ringtones
Step 3: Assigning a Custom Ringtone for a DP722/DP730 Handsets
1. Access DP752 Web GUI and go DECT → HS Settings → HS# Settings page.
2. In Custom Ringtone, select a custom ringtone from the dropdown list.
Note: If the list is not showing downloaded custom ringtone(s), press
and check again.
3. Press “Save and Apply”. DP722/DP730 handsets will download the ringtone locally before using it.
(DP722/DP730 LCD screen will display download progress at this stage).
4. On DP722/DP730 Handsets menu, access Settings → Audio → Ringtones. Select Custom
Ringtone using up/down arrow keys and press “Select” softkey.
Note: DP722/DP730 handsets can use one custom ringtone only.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 52
Date and Time
On the DP722/DP730, the Date and time are displayed on the idle screen and it obtains the date and time
from the Simple Network Time Protocol (SNTP) server by default. If your handsets cannot obtain the date
and time from the SNTP server, you need to configure the date and time manually. You can configure the
time format and date format respectively. The handsets supports two formats for time (12 Hour or 24 Hour)
and three date formats (DD/MM/YYYY; MM/DD/YYYY; YYYY/MM/DD).
To configure date and time manually
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to Date and time. Edit the current values in the Date & Time fields (you can change the
date / time format using the left key
or right key
and press “Set”.
4. Press “Save” softkey to apply your changes.
Figure 29: Date and Time Settings
Gestures (DP730 only)
To configure Gesture options, follow instructions below:
1. On DP730 LCD Menu Settings, select Settings → Gestures.
2. Set “Close-to-Ear Backlight” to On, to enable the LCD backlight when the handset is close to
ear.
3. Set “Facedown Hangup” to On, to enable the call hangup when the handset is put down on its
face.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 53
Figure 30: DP730 Gestures
Facedown Hangup
If “Facedown Hangup” option is set to ON, if DP730 is placed face down it will:
•
Reject incoming calls.
•
Hang up ongoing call.
Figure 31: DP730 Gestures – Facedown Hangup
Close-to-Ear Backlight
If “Close-to-Ear Backlight” is OFF (default):
If “Close-to-Ear Backlight” is ON:
Figure 32: DP730 Gestures – Close-to-Ear Backlight
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 54
Factory Functions
The factory functions include the following diagnostic options:
•
Keypad Diagnostic ( on DP730) / Diagnostic Mode ( on DP722)
•
Audio loopback
•
LCD on / off
•
LCD diagnostic
•
System Monitoring
•
Vibration ( DP730 only)
•
Acceleration Sensor ( DP730 only)
•
Proximity sensor ( DP730 only)
1. Press Menu (left softkey or the selection key) to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Factory Functions and choose which diagnostic, you need to perform:
Diagnostic Mode (DP722) / Keypad Diagnostic (DP730)
All LEDs will light up. All keys’ name will display in red on LCD screen before diagnosing. Press any
key on the keypad to diagnose the key’s function. When done, the key’s name will display in blue
on LCD with a prompt message (PASS). To exit press “Back” (right softkey).
Note: Long arrow UP key at any time to exit diagnostic mode.
Audio loopback
Speak to the phone using speaker/handsets/headset. If you can hear your voice, your audio is
working fine. Press “Back” (left softkey) to exit audio loopback mode.
LCD ON / OFF
Selects this option to turn off LCD. Press any button to turn on LCD.
LCD Diagnostic
Enters this option and press Left/Right arrow key to do LCD Diagnostic (you will notice that the color
of the LCD will be changing). Press right softkey to quit.
System Monitoring
Displays RSSI, battery voltage and RPN information.
Vibration (DP730 only)
Press “Vibrate” key to test if device vibrates normally. Press right softkey to quit.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 55
-
Acceleration Sensor (DP730 only)
Displays X, Y, Z coordinates. Change handset position and check new values. Press right softkey
to quit.
Proximity Sensor (DP730 only)
Cover the proximity sensor, when the sensor is covered, the gray dot displayed on screen will
become green. Press right softkey to quit.
Figure 33: Factory Functions
DP722/DP730 Handsets Firmware Upgrade
The DP722/DP730 handsets can detect if a new firmware is available when it is registered to a base station.
Figure 34: Firmware Notification
To upgrade the firmware on your handsets, follow the steps below:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Firmware Upgrade and press the softkey “Select”.
4. The LCD screen will display a prompt message to confirm the firmware downloading / upgrading
press the right softkey “Back” to dismiss the upgrade process.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 56
Figure 35: Firmware Upgrade
Reboot DP752 Base Station
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
3. Navigate to select Settings → System Settings and choose Reboot Base.
4. Enter Base PIN code (by default the PIN code is: 0000).
5. The LCD screen will display a prompt message to confirm rebooting the base station, press “Yes”
(left softkey) to confirm or press “No” (right softkey) to cancel.
Figure 36: Rebooting the Base Station
Reset DP722/DP730 Handsets
The users can reset the new settings made on the handsets after performing factory reset. To reset your
handsets to the default settings:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Settings
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 57
3. Navigate to select Settings → System Settings and choose Factory Reset.
4. The LCD screen will display a prompt message to confirm restoring factory settings, press “Yes” (left
softkey) to confirm and then the handsets will reboot to apply the default settings or press “No” (right
softkey) to cancel.
Figure 37: Resetting the Base Station
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 58
CALL OPERATIONS
Outgoing Default Line
When a Handsets is configured with more than one line, users can change the default outgoing line on
DP730/DP722 handset using keypad Menu → Preferences → Outgoing Default Line.
Figure 38: Outgoing Default Line
Placing calls
To place calls, you can use the following mode:
•
Earpiece mode: pressing the off-hook key to dial out.
•
Speakerphone mode: pressing the speakerphone key to dial out.
•
Headset mode: pressing the off-hook key to dial out using connected headset.
During the call, you can switch the call mode by pressing the corresponding keys or connecting a headset.
Make a Call using a Line
Making calls require the use of SIP lines. So, you should first register the SIP account to the handsets
beforehand, after registering the SIP lines, you can assign one or more outgoing lines for the handsets. The
handsets can only use the assigned outgoing line(s) to place calls.
Please refer to the following methods to make calls using a line:
Method 1:
▪
Via default outgoing line:
1. Enter the desired number using the keypad.
2. Press Dial key
or Speaker key
. The handsets will use the default outgoing line to dial out.
3. To terminate the call, press Hang-Up key
Note: To change the default outgoing line, please refer to Outgoing Default line.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 59
▪
Selecting the outgoing line:
1. Enter the desired number using the keypad.
2. Press the left softkey “Call”.
3. Select the desired line to dial out.
4. To terminate the call, press Hang-Up key
Method 2:
1. Press Dial key
or Speaker key
to enter the pre- dialing screen.
2. Enter the number to dial using the keypad.
3. Press Dial key
, # key (“Use # as dial key” must be configured in web configuration) or wait
for 4 seconds and the call will be initiated automatically.
4. To terminate the call, press Hang-Up key
During the call, you can switch the call mode by pressing the corresponding keys and cancel the dialing
operation by pressing the on-hook key. During the call conversations, you can press the left and right
navigation keys to adjust the volume. The call duration is displayed on the LCD screen while the call is in
progress and call summary will be displayed once the call is terminated.
Notes:
•
To dial “+” please keep pressing “0” key for about 2 seconds.
•
To dial from contacts list, choose a contact using navigation keys and press Dial key.
Dialing from Call history
Users may use their call history entries to initiate calls.
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Call History Icon
3. Select the desired entry, then press Dial key
and then press “Select”.
to establish the call.
Note: In step 3, users can press “Options” softkey followed by “Edit Dial” option to initiate the call.
The call history list stores the last dialed phone numbers. When the memory of the redial number list is full,
the handsets will automatically erase the oldest dialed number when a new number is dialed
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 60
Dialing from Phonebook
Users may use their private or shared contacts to initiate calls.
1. Press Menu to bring up operation menu.
2. Press Contacts to access phonebook menu.
3. Select the contact to call.
4. Press Dial Key
to initiate the call.
Note: In step 4, users can press “Options” softkey followed by “Edit Dial” option to initiate the call.
Answering Calls
When receiving an incoming call, you can answer the call using following steps:
•
Earpiece mode:
Press Dial Key
•
Speakerphone mode:
Press Speaker Key
•
to pick up the call, or “Accept” softkey (left softkey).
to pick up the call.
Headset mode:
Press Dial Key
to pick up the call, or “Accept” softkey using a connected headset.
Notes:
To answer an incoming call during an established call, press Dial Key
, or the Speaker Key
or the “Answer” softkey. The incoming call is answered, and the original call is placed on hold.
You can switch off the ringer temporarily by pressing Silent softkey.
Auto Answer
Users can enable Auto Answer feature to accept and automatically answer incoming calls.
If enabled, DP722/DP730 Handsets will automatically answer incoming calls using speaker mode.
To activate / deactivate the auto answer feature:
•
Using DP722/DP730 Handsets Menu
1. Press Menu to bring up operation menu.
2. Select Preferences → navigate to Auto Answer using the up/down arrow keys.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 61
3. Switch between Enabled/Disabled using left/right arrow keys and “Save” after Enabling / Disabling
the option.
•
Using DP752 Base Station Web Interface
1. Access DP752 Base Station Web Interface.
2. Go to DECT → Handsets Settings → HS# Settings.
3. Set “Enable Auto Answer” to “Yes”. (By default, set to “No”).
Off-Cradle Pickup
Users can enable Off-Cradle Pickup feature to automatically answer incoming calls after picking up
DP722/DP730 Handsets from its cradle. Incoming calls will be automatically answered using earpiece mode.
Notes:
▪
DP722/DP730 Handsets should be resting on its cradling and then picked up for this feature to
work.
▪
“Auto Answer” feature should be set to “No” to work properly.
To activate / deactivate the off-cradle pickup:
•
Using DP722/DP730 Handsets Menu
1. Press Menu to bring up operation menu.
2. Select Preferences → navigate to Off-Cradle Pickup using the up/down arrow keys.
3. Switch between Enabled/Disabled using left/right arrow keys and “Save” after Enabling / Disabling
the option.
•
Using DP752 Base Station Web Interface
1. Access DP752 Base Station Web Interface.
2. Go to DECT → Handsets Settings → HS# Settings.
3. Set “Enable Onhook on Cradle Reposition” to “Yes”. (By default, set to “No”).
Ending Calls
To terminate the calls, press Hang-Up key
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 62
On-Cradle Hang-up
Users can enable On-Cradle Hang-up feature to automatically end ongoing calls after placing DP722/DP730
Handsets on its cradle.
To activate / deactivate the on-cradle hang-up feature:
•
Using DP722/DP730 Handsets Menu
1. Press Menu to bring up operation menu.
2. Select Preferences → navigate to On-Cradle Hang-up using the up/down arrow keys.
3. Switch between Enabled/Disabled using left/right arrow keys and “Save” after Enabling / Disabling
the option.
•
Using DP752 Base Station Web Interface
1. Access DP752 Base Station Web Interface.
2. Go to DECT → Handsets Settings → HS# Settings.
3. Set “Enable Off hook on Cradle Pickup” to “Yes”. (By default, set to “No”).
Rejecting Calls
To reject an incoming call, press Hang-Up key
or “Reject” softkey (right softkey)
Direct IP Call
Direct IP calling allows two parties, that is, a handsets and another VoIP device, to talk to each other in an ad
hoc fashion without a SIP proxy.
Elements necessary to complete a Direct IP Call:
•
Both DP722/DP730 and other VoIP Device, have public IP addresses, or
•
Both DP722/DP730 and other VoIP Device are on the same LAN using private IP addresses, or
•
Both DP722/DP730 and other VoIP Device can be connected through a router using public or private
IP addresses (with necessary port forwarding or DMZ).
Users can perform IP calls using Star code following the below steps:
1. Pick up the handsets and press Dial key
2. Dial *47 followed by the target IP Address.
Note: You can enter directly *47 + target IP address, and then press the dial key to initiate the call.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 63
Examples of direct IP calls
a) If the target IP address is 192.168.0.160, the dialing convention is *47 then 192*168*0*160, followed
by pressing the “#” key if it is configured as a send key or wait 4 seconds. In this case, the default
destination port 5060 is used if no port is specified.
b) If the target IP address/port is 192.168.1.20:5062, then the dialing convention would be:
*47 or Voice Prompt with option 47, then 192*168*0*160*5062 followed by pressing the “#” key if
it is configured as a send key or wait for 4 seconds.
Note: To accept incoming direct IP call, Use Random Port setting should be set to NO. If set to YES, it
can only dial out. The setting is available on DP752 web interface → Profile → SIP Settings → Basic
Settings.
Call Hold/Resume
During an established call, you can put the call on hold and resume following below steps:
1. Press the left softkey to access the call Options and then navigate to Hold.
2. Press “Select”, left softkey to put the call on hold.
3. To resume the call, access the options menu again and navigate to Resume, then press Select.
If you press
initial call, press
during the call, the first call will be on hold, and you can establish a new call; to resume the
Call Waiting
This feature will notify you of a new incoming call during an established call, and display the incoming call
information visually on the LCD screen and a call waiting tone will be heard. If this feature is disabled, the
new incoming call will be automatically rejected.
There are 2 ways to activate call waiting feature either using DP722/DP730 Handsets Menu or using DP752
Base Station Web Interface.
•
Using DP722/DP730 Handsets Menu
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Call Features
→ navigate to Call waiting sub-menu.
3. Select the account for which you want to enable the Call waiting feature, and then press left softkey
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 64
“Select”.
4. Choose between Enabled and Disabled options and press the softkey “Save”, a prompt message
will be displayed to confirm that the call waiting is enabled / disabled.
5. During an established call, press
(dial key) to put first call on hold and answers second incoming
call. If no second incoming call, pressing
will give the ability to initiate another call while first one
is on hold.
Note: You can switch between active/on-hold calls by pressing Options → Swap.
•
Using DP752 Base Station Web Interface
1. Access DP752 Base Station Web Interface.
2. Go to DECT → Handsets Settings → HS# Settings.
3. Set “Disable Call Waiting Tone” to “No”. (Default is No).
4. Press “Save and Apply” button to confirm.
Do Not Disturb
You can activate or deactivate the DND mode for your accounts registered on the handsets under the call
settings. If DND mode is activated for a specific line, all incoming calls will receive busy treatment depending
on your configuration (forward to voice mail, busy tone…)
To enable or disable the DND mode, follow the next steps
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Call Features
→ navigate to Do Not Disturb sub-menu.
3. Select the account on which you want to enable / disable the DND mode and then press “Select”
4. Choose between Enabled and Disabled options and press softkey “Save” to accept the changes, a
prompt message will be displayed to confirm that the DND is enabled / disabled.
You can navigate to Status → Line status to check if the DND mode is enabled on the base station.
You can also navigate via web interface of DP752 → Status → Line Options.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 65
Call Forward
The call forward feature will allow you to forward all the incoming calls to the desired number. Three possible
call forward types are available on the DP722/DP730.
▪
Forward all Dest: All the incoming calls are immediately forwarded.
▪
Forward Busy Dest: Incoming calls are immediately forwarded if the line is busy.
▪
Forward No Answer Dest: Incoming calls are forwarded if not answered after a period of time.
To enable the call forward, please refer to the following steps:
1. Press Menu to bring up operation menu.
2. Use arrow keys to reach Call Features
→ navigate to Call Forward sub-menu.
3. Select the account on which you want to enable/disable the call forward feature and press “Select”.
4. Select the type of call forwarding and enter the number to forward the calls, and then press “Save”
(left softkey) to apply the settings, a prompt message will be displayed to confirm that the new settings
have been saved successfully.
Call Transfer
The DP722/DP730 supports the call transfer feature, you can transfer a call to another party using one
of the following ways:
▪
Blind transfer: Transfer a call directly to another party without consulting
▪
Attended transfer: Transfer a call with prior consulting.
Blind Transfer
1. Press the “Options” softkey during a call, and then select Transfer.
2. The initial call will be on hold, enter the number you want to transfer the call to.
3. Press Dial key
. The call is connected to the number or the handsets you specified, and the LCD
screen prompts Call Transferred.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 66
Attended Transfer
1. Press Left softkey “Options” during a call, and then select New call.
2. Choose the line and enter the number you want to transfer the call to, then press Dial key
3. Once the second call is established, press left softkey “Option” and select Transfer.
Speed Dial
Speed dial allows users to perform single-digit dialing to predefined numbers. This feature is particularly
useful to speed up dialing frequently used or hard to remember numbers. A maximum of 8 speed dial numbers
is allowed.
For example, the digit key 2 is configured as a speed dial key and assigned the number 2000, the phone will
dial out the number 2000 directly when you long press digit key 2.
❑ To assign the frequently used numbers as speed dial keys:
1. Press Menu to bring up operation menu.
2. Access to Shortcut
and then use Arrow keys to reach Speed Dial sub-menu.
Or;
Long press the representative number from 2 to 9 to set. (Note: The Speed dial number should not
be already set on chosen representative number, otherwise long press will initiate a call to configured
speed dial number).
3. Choose the digit key (2-9) to set and press Options or OK button. Three options will be available:
•
Edit: To configure manually a contact as speed dial. Users need to enter “First Name”, “Last
Name” and “Number”. (Note: First Name + Number or Last Name + Number are accepted).
•
From Contacts: To set a contact from the phonebook directory to be as speed dial.
❑ To Modify a Speed Dial:
Repeat above 2 steps.
At step 2, re-edit /re-assign a contact from the shared or private directory as speed dial on selected key.
❑ To Delete a Speed Dial:
Repeat above 2 steps.
At step 2, select Clear Entry option and press OK or Select to confirm.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 67
3-Way Conference
The DP722/DP730 supports creating a local conference with other parties (including handsets starting the
conference).
To start a 3 Way conference, follow below steps:
1. Press the Dial key
to place a call to the first party.
2. Press left softkey “Options”, then select Conference.
3. Enter second party number you want to add to the conference and press Dial Key
To drop the conference call, press
or “End” softkey.
Note: Conference can be bridged before third party answers.
Voice Mail
The voice mail feature ensures that you will never miss any important messages. It permits either to leave
voice mails to someone else or receive and listen to voice mails via the handsets
Set Voice Mail Feature Code
There are 2 ways to set Voice Mail Feature Code, either using DP722/DP730 Handsets Menu or using DP752
Base Station Web Interface.
Note: The Voice Mail Feature Code depends on the service provider or IP-PBX used. For example, if
UCM6xxx as SIP server, the Voice Mail Feature Code is *97.
•
Using DP722/DP730 Handsets Menu
1. Press Menu (left softkey or the selection key) to bring up operation menu.
2. Access to Voice Mail
and then select Set Voice Mail sub menu.
3. Select the account and enter the “VM Access Number”, then press “Save” softkey.
•
Using DP752 Base Station Web Interface
1. Access DP752 Base Station Web Interface.
2. Go to Profiles → Profile X → General Settings.
3. Configure Voice Mail Access Number.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 68
Play Voice Mail Messages
1. Press “Menu” to bring up operation menu.
2. Access to Voice Mail
and then select Play Message sub menu.
3. Select the account to retrieve your voice messages saved on your voice mail.
Or;
Long press digit “1” key to dial configured Voice Mail feature code using Default Line.
Notes:
•
Users can access directly voicemail menu to play messages, by clicking on “View” (left softkey) when
the notification of a new voicemail pops up on the DP722/DP730’s LCD screen.
•
If VM is protected by a password, users can enter the password using DP722/DP730 keypad after
reaching Voice Mail system. The password is defined on the service provider or IP-PBX side.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 69
PTT (Push-To-Talk) Key for DP730
The DP730/722 support the Push to talk (PTT) features which is a technology based on the instantaneous
communication commonly employed in wireless cellular phone services using a button to switch the device
from voice transmission mode to voice reception mode.
1. Users could press and hold the Push-to-talk key from any screen to quickly initiate PTT call.
Figure 39: PTT Feature Enabled
2. The channel status will change to Sending PTT to indicate that you are transmitting as displayed on
the following screenshot
Figure 40: PTT Transmission
To terminate PTT call, press
button.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 70
Call Features
The DP752/DP722/DP730 supports traditional and advanced telephony features including call forward and
etc.
Table 17: Call Features
Unconditional Call Forward. To set up unconditional call forward:
*72
•
Off hook the phone;
•
Dial *72 and then enter the number to forward the call;
•
Press OK softkey or SEND key.
Cancel Unconditional Call Forward. To cancel the unconditional call forward:
*73
•
Off hook the phone;
•
Dial *73;
•
Hang up the call.
Busy Call Forward. To set up busy call forward:
*90
•
Off hook the phone;
•
Dial *90 and then enter the number to forward the call;
•
Press OK softkey or SEND key.
Cancel Busy Call Forward. To cancel the busy call forward:
*91
•
Off hook the phone;
•
Dial *91;
•
Hang up the call.
Delayed Call Forward. To set up delayed call forward:
*92
•
Off hook the phone;
•
Dial *92 and then enter the number to forward the call;
•
Press OK softkey or SEND key.
Cancel Delayed Call Forward. To cancel the delayed call forward:
*93
•
Off hook the phone;
•
Dial *93;
•
Hang up the call.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 71
RESTORE FACTORY DEFAULT SETTINGS
Warning:
Restoring the factory default settings will delete all configuration information on the phone. Please backup or
print all the settings before you restore to the factory default settings. Grandstream is not responsible for
restoring lost parameters and cannot connect your device to your VoIP service provider.
Please follow the instructions below to reset the phone:
1. Press MENU button to bring up the keypad configuration menu;
2. Select Settings and enter;
3. Select System Settings → Factory Reset;
4. A warning window will pop out to make sure a reset is requested and confirmed;
5. Press Yes softkey to confirm and the phone will reboot.
6. To cancel the Reset, press No softkey instead.
Users also can perform factory reset using combo keys on DP722/DP730 during booting up prior it’s fully
booted, to give DP722/DP730 the ability to recover from some extreme cases like self-reboot or stuck right
after booted up.
Please refer to following procedure for DP722/DP730 factory reset using combo key:
1. Connect the USB cable and power off DP722/DP730.
2. Power on DP722/DP730 and wait for Green LED.
3. Press 3 times Central Key (OK/Selection Key) quickly after Green LED on.
4. Press Speaker Key (left bottom) first and then Mute Key (right bottom) after Red LED on.
5. DP722/DP730 LED will start blinking in 3 colors: Green, Red and Orange if factory reset successful
triggered.
6. Wait for about 1-3 minutes, the DP722/DP730 will boot up with setup wizard for initial language and
date format settings.
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 72
FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any Changes or modifications not
expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Exposure to Radio Frequency (RF) Signals
For Handset
This is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limitsfor
exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the
U.S.Government. These limits are part of comprehensive guidelines and establish permitted levels of RF
energy for the general population. The guidelines are based on the safety standards previously set by both
U.S. and international standards bodies. These standards include a substantial safety margin designed to
assure the safety of all persons,regardless of age and health. The belt clip must be used when use the device
It and its antenna must not be
- co- located or operating in conjunction with any other antenna or transmitter.
This product has been shown to be capable of compliance for localized specific absorption rate (SAR) for
uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and
had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65
Supplement C (2001) and IEEE 1528.
For Base
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
EXPERIENCING DP752/DP722/DP730
Please visit our website: http://www.grandstream.com to receive the most up- to-date updates on firmware
releases, additional features, FAQs, documentation and news on new products.
We encourage you to browse our product related documentation, FAQs and User and Developer Forum for
answers to your general questions. If you have purchased our products through a Grandstream Certified
Partner or Reseller, please contact them directly for immediate support.
Our technical support staff is trained and ready to answer all your questions. Contact a technical support
member or submit a trouble ticket online to receive in-depth support.
Thank you again for purchasing the Grandstream DP722/DP730 / DP752, it will be sure to bring convenience
and color to both your business and personal life.
Grandstream Networks,Inc.
126 Brookline Ave., 3rd Floor Boston, MA 02215, USA
DP752/DP722/DP730 User Guide
Version 1.0.5.9
P a g e | 73

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Create Date                     : 2018:11:05 10:14:24Z
Creator                         : Microsoft® Word for Office 365
Modify Date                     : 2018:12:07 09:24:06-08:00
Language                        : fr-FR
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Microsoft® Word for Office 365
Creator Tool                    : Microsoft® Word for Office 365
Metadata Date                   : 2018:12:07 09:24:06-08:00
Document ID                     : uuid:CE043139-A173-459C-B7A7-26F743005199
Instance ID                     : uuid:013598c9-61db-41ca-bb8e-aab742c7f9ca
Format                          : application/pdf
Page Count                      : 75
EXIF Metadata provided by EXIF.tools
FCC ID Filing: YZZDP752

Navigation menu